INSTALLATION INSTRUCTIONS FOR PART 99-8211
APPLICATIONS
2000-04 TOYOTA AVALON
99-8211
KIT FEATURES
• DIN Head Unit Provisions with Pocket
• ISO DIN Head Unit Provisions with Pocket
KIT COMPONENTS
A) Radio Housing
I
B) ISO Brackets
I
C) ISO Trim Plate I D) Radio Housing Brackets
D
B
A
C
TOOLS REQUIRED:
Small Flat Blade Screwdriver I Phillips Screwdriver I Socket Wrench
1-800-221-0932
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8211
2000-2004 TOYOTA AVALON
(column shift models)
A
Disconnect the negative battery terminal
to prevent an accidental short circuit.
1
2
Unsnap the trim below the climate
control to reveal (2) 10 MM bolts
and remove. (Figure A)
B
Carefully pull air vents above radio
towards rear of car to unsnap. Note:
There are (3) snaps, (2) are at the bottom
3
C
sides and (1) is at the top middle of the
vent assembly. (Figure B)
Remove (2) 10 MM bolts from above
radio/climate control assembly and
remove assembly together. (Figure C)
4
5
D
Remove (6) Phillips screws (4 from radio
and 2 from climate control) from each
side bracket to separate radio and cli-
mate control. (Figure D)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8211
2000-2004 TOYOTA AVALON
(console shift models)
A
Disconnect the negative battery terminal
to prevent an accidental short circuit.
1
2
Open the center console armrest,
unsnap cover above cup holder and
remove (2) Phillips screws toward
the outside of the panel. (Figure A)
B
3
4
Lift up and remove shifter trim/ashtray
assembly. (Figure B)
Unsnap black cover from under climate
controls and remove (2) 10 MM bolts.
(Figure C)
C
D
Carefully pull air vents above radio
towards rear of car to unsnap. Note:
There are (3) snaps, (2) are at the bottom
sides and (1) is at the top middle of the
vent assembly. (Figure D)
3
Remove (2) 10 MM bolts from above
radio/climate control assembly and
remove assembly together. (Figure E)
4
5
E
F
Remove (6) Phillips screws (4 from radio
and 2 from climate control) from each
side bracket to separate radio and cli-
mate control. (Figure F)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8211
DIN Head Unit Provision
A
Slide the mounting bracket
1
2
onto the 99-8211 until side
clips engage. (Figure A)
Slide factory climate controls
into the 99-8211 and secure
using the factory hardware.
(Figure B)
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure C)
3
B
Slide the aftermarket head unit
into the cage and secure.
4
5
Snap the Trim plate into the
Radio Housing.
C
3
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8211
ISO DIN HEAD UNIT PROVISION
A
Slide the mounting bracket onto
the 99-8211 until side clips
engage. (Figure A)
1
2
Slide factory climate controls
into the 99-8211 and secure
using the factory hardware.
(Figure B)
Mount the ISO Brackets to the
head unit with the screws sup-
plied with the unit.
3
4
B
Slide the head unit into the radio
opening until the side clips
engage. (Figure C)
Snap the Trim plate into the
Radio Housing.
5
C
4
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8211
A
B
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
C
D
Tape
Locate the factory wiring harness in the dash.
Metra recommends using the proper mating
adapter and making the connections as shown.
(Isolate and individually tape off the ends of
any unused wires to prevent electrical short
circuit)
1
2
3
Re-connect the negative battery terminal and test
the unit for proper operation.
Reassemble radio and dash assemblies in
reverse order of disassembly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8211
6
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8211
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INST998211
1-800-221-0932
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
|