Power Amplifier
MC1.2KW
Owner’s Manual
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank You
Table of Contents
Your decision to own this McIntosh MC1.2KW Power
Amplifier ranks you at the very top among discriminating
music listeners. You now have “The Best.” The McIntosh
dedication to “Quality,” is assurance that you will receive
many years of musical enjoyment from this unit.
Please take a short time to read the information in this
manual. We want you to be as familiar as possible with all
the features and functions of your new McIntosh.
Safety Instructions............................................................. 2
Thank You and Please Take a Moment.............................. 3
Technical Assistance and Customer Service..................... 3
Table of Contents ............................................................... 3
General Information .......................................................... 3
Connector Information ...................................................... 4
Introduction........................................................................ 4
Performance Features ........................................................ 4
Dimensions ........................................................................ 5
Installation ......................................................................... 6
Rear Panel Connections and Switch.................................. 7
How to Connect .............................................................. 8-9
How to Connect for Bi-Amp........................................10-11
Front Panel Displays and Controls....................................12
How to Operate.................................................................13
Technical Description ..................................................14-17
Specifications....................................................................18
Packing Instruction...........................................................19
Please Take A Moment
The serial number, purchase date and McIntosh Dealer
name are important to you for possible insurance claim or
future service. The spaces below have been provided for
you to record that information:
Serial Number: __________________________________
Purchase Date: __________________________________
Dealer Name: ___________________________________
General Information
Caution: The MC1.2KW Amplifier weight is 147 pounds (66.7
kilograms). It requires two or more persons to safely
handle when moving the amplifier.
1. The following Connecting Cable is available from the McIn-
tosh Parts Department:
Technical Assistance
If at any time you have questions about your McIntosh
product, contact your McIntosh Dealer who is familiar
with your McIntosh equipment and any other brands that
may be part of your system. If you or your Dealer wish
additional help concerning a suspected problem, you can
receive technical assistance for all McIntosh products at:
Power Control Cable Part No. 170-202
Six foot, 2 conductor shielded, with two 1/8 inch stereo
mini phone plugs.
2. For additional connection information, refer to the owner’s
manual(s) for any component(s) connected to the MC1.2KW.
3. The MC1.2KW mutes the speaker output for approximately
two seconds when first turned on.
4. It is very important that loudspeaker cables of adequate size
be used, so that there will be no power loss. The size is speci-
fied in Gauge Numbers or AWG, (American Wire Gauge). The
smaller the Gauge number, the larger the wire size:
If your loudspeaker cables are 50 feet (38.1m) or less, use
at least 14 Gauge.
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, New York 13903
Phone: 607-723-1545
Fax: 607-724-0549
Customer Service
If it is determined that your McIntosh product is in need of
repair, you can return it to your Dealer. You can also return
it to the McIntosh Laboratory Service Department. For
assistance on factory repair return procedure, contact the
McIntosh Service Department at:
If your loudspeaker cables are 100 feet (76.2m) or less,
use at least 12 Gauge.
5. In the event the MC1.2KW over heats, due to improper
ventilation and/or high ambient temperature, the protection
circuits will activate. The Front Panel Power Guard LED will
continuously indicate ON and the audio will be muted. When
the MC1.2KW has returned to a safe operating temperature,
normal operation will resume.
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, New York 13903
Phone: 607-723-3515
6. The MC1.2KW incorporates the very latest in Fully Double
Balanced Circuitry. As a result, the Loudspeaker
Negative
Connections are above chassis ground. Do not combine any
connections together, ground them or connect with another
MC1.2KW.
Fax: 607-723-1917
Copyright 2007 © by McIntosh Laboratory, Inc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector Information, Introduction and Performance Features
Connector and Cable Information
XLR Connectors
• Power Guard
Below is the Pin configuration for the XLR Balanced Input The patented McIntosh Power Guard circuit prevents the
Connectors on the MC1.2KW. Refer to the diagram for
connection:
amplifier from being over driven into clipping, with its
harsh distorted sound that can also damage your valuable
loudspeakers.
PIN 1: Shield/Ground
PIN 2: + Output
PIN 3: - Output
• Sentry Monitor and Thermal Protection
McIntosh Sentry Monitor power output stage protection
circuits ensure the MC1.2KW will have a long and trouble
free operating life. Built-in Thermal Protection Circuits
guard against overheating.
PIN 2
PIN 1
PIN 3
Power Control Connector
The MC1.2KW’s Power Control Inputs receive On/Off
signals of +5 volts. An additional con-
Power
nection is for controlling the illumina-
Control
tion of the MC1.2KW Power Output
Meter
• Patented Autoformer
Meters. The 1/8 inch stereo mini
phone plug connects to a McIntosh
McIntosh designed and manufactured Output Autoformers
provide an ideal match between the amplifier output stages
and speaker loads of 2, 4 and 8 ohms. The Autoformers
also provide perfect DC protection for your valuable loud-
speakers.
Illumination
Control
Ground
A/V Control Center Power Control
Output.
Note: The Power Control Connecting Cable is available from
the McIntosh Parts Department:
Data and Power Control Cable Part No. 170-202
Six foot, shielded 2 conductor, with 1/8 inch stereo mini
phone plugs on each end.
• Special Power Supply
A regulated Power Supply, a very large Toroidal Wound
Power Transformer and very large capacitors ensures sta-
ble noise free operation even though the power line varies.
Introduction
• Illuminated Power Meter
Now you can take advantage of traditional McIntosh
standards of excellence in the MC1.2KW Power Ampli-
fier. The 1,200 watt high current output will drive any high
quality loudspeaker system to its ultimate performance.
The MC1.2KW reproduction is sonically transparent and
absolutely accurate. The McIntosh Sound is “The Sound of
the Music Itself.”
The Illuminated Power Output Watt Meter on the
MC1.2KW is peak responding, and indicates the true
power output of the amplifier. The Peak Watt Hold Mode
allows the meter to temporarily stay at the highest power
output and then slowly decay. The Front Panel Meter Il-
lumination may be switched Off at any time.
• Fiber Optic Solid State Front Panel Illumination
The even Illumination of the Front Panel is accomplished
by the combination of custom designed Fiber Optic Light
Diffusers and extra long life Light Emitting Diodes
(LEDs).
Performance Features
• Power Output
The MC1.2KW is a Power Amplifier with a capability
of 1,200 watts into 2, 4 or 8 ohm speakers with less than
0.005% distortion.
• Glass Front Panel and Super Mirror Chassis Finish
The famous McIntosh Illuminated Glass Front Panel and
the Stainless Steel Chassis with Super Mirror Finish en-
sures the pristine beauty of the MC1.2KW will be retained
for many years.
• Full Balanced Quad-Differential Circuitry
The MC1.2KW is fully balanced from inputs to outputs.
It consists of two matched power amplifiers operating in
push-pull with their outputs combined in a McIntosh Auto-
former. The double balanced configuration cancels virtu-
ally all distortion.
• Balanced and Unbalanced Inputs
Balanced connections guard against induced noise and al-
low long cable runs without compromising sound quality.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Dimensions
The following dimensions can assist in determining the
best location for your MC1.2KW. There is additional
information on the next page pertaining to installing the
MC1.2KW into cabinets.
17-3/4"
45.09cm
11"
27.94cm
12-5/16"
31.27cm
Front View of the MC1.2KW
17-3/8"
44.15cm
Rear View of the MC1.2KW
12-1/4"
31.11cm
19-1/2"
49.50cm
18"
45.72cm
1-5/8"
4.12cm
10-1/2"
26.70cm
Side View of the MC1.2KW
3/16"
0.48cm
1-1/2"
3.81cm
14"
35.60cm
1-9/16"
3.96cm
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
The MC1.2KW can be placed upright on a table or shelf,
standing on its four feet. It also can be custom installed
in a piece of furniture or cabinet of your choice. The four
feet may be removed from the bottom of the MC1.2KW
when it is custom installed as outlined below. The four
feet together with the mounting screws should be retained
for possible future use if
out a ventilation hole in the mounting shelf according to
the dimensions in the drawing.
1 When the MC1.2KW is installed together with other McIntosh
Components, check clearances on all components before
proceeding.
the MC1.2KW is removed
from the custom installa-
17-9/16"
44.62cm
tion and used free standing.
The required panel cutout,
ventilation cutout and unit
dimensions are shown.
Always provide ad-
10 -13/16"
27.46cm
equate ventilation for your
MC1.2KW. Cool operation
ensures the longest pos-
sible operating life for any
electronic instrument. Do
not install the MC1.2KW
directly above a heat gen-
erating component such as
a high powered amplifier.
If all the components are
installed in a single cabinet,
a quiet running ventilation
fan can be a definite asset in
maintaining all the system
components at the coolest
possible operating tempera-
ture.
MC1.2KW Front Panel
Custom Cabinet Cutout
6"
15.24cm
Cabinet
Front
Panel
Cutout Opening for Custom Mounting
Opening
for Ventilation
A custom cabinet instal-
lation should provide the
following minimum spacing
dimensions for cool opera-
tion.
MC1.2KW Side View
in Custom Cabinet
Chassis
Spacers
Allow at least 6 inches
Cutout Opening for Ventilation
(15.24cm) above the top, 2
inches (5.08cm) below the
bottom and 1 inch (2.54cm)
on each side of the Power
Amplifier, so that airflow
is not obstructed. Allow 19-
1/2 inches (49.53cm) depth
behind the front panel. Al-
low 1-5/8 inch (4.12cm) in
front of the mounting panel1
for clearance. Be sure to cut
Support
Shelf
1"
2.54cm
14-1/2"
36.83cm
21/32"
MC1.2KW Bottom View
in Custom Cabinet
1.67cm
15-5/16"
38.91cm
14"
35.56cm
Cutout Opening
for Ventilation
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel Connections and Switch
Circuit Breaker,
press to reset if
the amplifier will
not power up
BALANCED INPUT1 / OUT-
PUT for an audio cable from a
Preamplifieroutput or to connect
an audio cable onto the next
Power Amplifier input
BALANCED INPUT
for an audio cable
from a Preamplifier
or A/V Control Cen-
ter audio output
Connect the MC1.2KW
power cord to a live AC
outlet. Refer to the rear
panel to determine the
correct voltage
POWER CONTROL IN
UNBALANCED INPUT
INPUT MODE switch
receives turn On/Off sig-
nal from a McIntosh com-
ponent and the POWER
CONTROL OUT sends a
turn On/Off signal to the
next McIntosh Compo-
nent
for an audio cable from a
Preamplifier or A/V Con-
trol Center audio output
selects between balanced
or unbalanced input
OUTPUT Connections
for 2 ohm Loudspeaker
OUTPUT Connections
for 4 ohm Loudspeaker
OUTPUT Connections
for 8 ohm Loudspeaker
1 This Balanced connector may be used as an Input ONLY
when connected to a McIntosh C1000 Preamplifier. For
all other connections use only as an Output.
Caution: The Loudspeaker
Negative Connections are above
chassis ground. Do not combine any connections to-
gether, ground them or connect with another MC1.2KW.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect
Caution: The supplied AC Power Cord should not be con-
nected to the Rear Panel of the MC1.2KW Amplifier
until after the Loudspeaker Connections have been
made and the supplied protective Terminal Connec-
tions Cover has been installed. Failure to observe
this could result in Electric Shock.
1. For Remote Power Control, connect a power control
cable from the Control Center or Preamplifier Power
Control Out to the MC1.2KW POWER CONTROL IN.
2. Connect a cable from the Balanced Output of a McIn-
tosh Preamplifier or Control Center to the MC1.2KW
BALANCED INPUT. Place the INPUT MODE Switch
in the BALANCED Position.
terminals so the lugs
cannot slip out. Refer to
figures 4, 5 & 6.
4. Connect the loud-
speaker hookup ca-
Figure 4
Figure 5
Figure 6
ble to the output terminals that match the impedance of
your loudspeaker, being careful to observe the correct
polarities. Output impedance connections of 2 ohms,
4 ohms and 8 ohms are provided. If the impedance of
your loudspeaker is in-between the available connec-
tions, use the nearest lower impedance connection.
WARNING: Loudspeaker terminals are hazardous live
and present a risk of electric shock. For ad-
Note: An optional hookup is to use an unbalanced cable
and place the INPUT MODE Switch in the UNBAL-
ANCED Position.
ditional instruction on making Loudspeaker
Connections contact your McIntosh Dealer
or McIntosh Technical Support.
3. Prepare the Loudspeaker Hookup Cable for attachment
to the MC1.2KW Power Amplifier:
5. Attach the supplied Terminal Connections Cover with
the four Phillips Head Mounting Screws (10-32 x 1/2
inch) to the Rear Panel of the MC1.2KW Amplifier.
Refer to figures 7a and 7b.
Note: There are six openings on the bottom edge of the
cover to allow the Loudspeaker’s Cable to exit the
MC1.2KW. The Rear Chassis Handle has tapped
screw openings on both sides for securing the cover.
6. Connect the MC1.2KW power cord to an active AC
outlet.
Bare wire cable ends:
Carefully remove sufficient insulation from the
cable ends, refer
to figures 1, 2 &
3. If the cable is
stranded, carefully
Figure 2
Figure 3
Figure 1
twist the strands
together as tightly as possible.
Notes: 1. If desired, the twisted ends can be tinned with
solder to keep the strands together.
Terminal
Connections
Cover
Cover
Mounting
Screw
Cover
Mounting
Screw
2. Banana plugs are for use in the United States
and Canada only. In the United States, when us-
ing the 8 ohm loudspeaker terminals, it is man-
datory to use banana plugs inserted into the top
hole of the loudspeaker terminals in order to
comply with safety standard requirements.
Connection Method for use inside the United States and
Canada only:
Rear
Chassis
Handle
Location
Location
Attach the previously prepared bare wire cable ends into
the banana plugs and
Cable
Openings
Figure 7a (Inside USA and Canada)
secure the connections.
Insert the banana plug
only into the hole at the
top of the terminal. Refer
to figures A and B.
Terminal
Connections
Cover
Cover
Mounting
Screw
Cover
Mounting
Screw
Rear
Chassis
Handle
Location
Location
Connection Method for use outside the United States
and Canada:
Attach the previously prepared bare wire cable ends into
the spade lug connectors and secure the connections.
Insert the spade lug connector or prepared section of the
cable end into the terminal side access hole, and tighten
the terminal cap until the cable is firmly clamped into the
Cable
Openings
Figure 7b (Outside USA and Canada)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect
McIntosh Preamplifier
Connect to
AC Outlet
McIntosh
Loudspeaker
9
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect for Bi-Amp
Caution: The supplied AC Power Cord should not be con-
nected to the Rear Panel of the MC1.2KW Amplifier
until after the Loudspeaker Connections have been
made and the supplied protective Terminal Connec-
tions Cover has been installed. Failure to observe
this could result in Electric Shock.
1. For Remote Power Control, connect a power control
cable from the Control Center or Preamplifier Power
Control Out to the MC1.2KW (Amplifier One) POWER
CONTROL IN.
2. Connect a power control cable from MC1.2KW (Ampli-
fier One) POWER CONTROL OUT to the MC1.2KW
(Amplifier Two) POWER CONTROL IN.
3. Connect a cable from the Balanced Output of a McIn-
tosh Preamplifier or Control Center to the MC1.2KW
(Amplifier One) BALANCED INPUT. Place the IN-
PUT MODE Switch in the BALANCED Position.
Note: An optional hookup is to use an unbalanced cable
and place the INPUT MODE Switch in the UNBAL-
ANCED Position.
Refer to figures A and
B.
Figure 4
Figure 5
Figure 6
Connection Method
for use outside the
United States and Canada:
Attach the previously prepared bare wire cable ends into
the spade lug connectors and secure the connections. Insert
the spade lug connector or prepared section of the cable
end into the terminal side access hole, and tighten the ter-
minal cap until the cable is firmly clamped into the termi-
nals so the lugs cannot slip out. Refer to figures 4, 5 & 6.
4. Connect the loudspeaker hookup cable to the output ter-
minals that match the impedance of your loudspeaker,
being careful to observe the correct polarities. Output
impedance connections of 2 ohms, 4 ohms and 8 ohms
are provided. If the impedance of your loudspeaker is
in-between the available connections, use the nearest
lower impedance connection.
WARNING: Loudspeaker terminals are hazardous live
4. Connect a cable from
and present a risk of electric shock. For ad-
ditional instruction on making Loudspeaker
Connections contact your McIntosh Dealer
or McIntosh Technical Support.
the BALANCED
INPUT/OUTPUT of
the MC1.2KW (Am-
Figure 2
Figure 3
Figure 1
plifier One) to the
5. Attach the supplied Terminal Connections Cover with
the four Phillips Head Mounting Screws (10-32 x 1/2
inch) to the Rear Panel of the MC1.2KW Amplifier.
Refer to figures 7a and 7b ( on the next page).
Note: There are six openings on the bottom edge of the
cover to allow the Loudspeaker’s Cable to exit the
MC1.2KW. The Rear Chassis Handle has tapped
screw openings on both sides for securing the cover.
6. Connect the MC1.2KW power cord to an active AC
outlet.
MC1.2KW (Amplifier Two) BALANCED INPUT.
5. Prepare the Loudspeaker Hookup Cable for attachment
to the MC1.2KW Power Amplifier:
Bare wire cable ends:
Carefully remove sufficient insulation from the cable
ends, refer to figures 1, 2 & 3. If the cable is strand-
ed, carefully twist the strands together as tightly as
possible.
Notes: 1. If desired, the twisted ends can be tinned with
solder to keep the strands together.
2. Banana plugs are for use in the United States
and Canada
only. In
the United
States,
when using
the 8 ohm
Terminal
Connections
Cover
Cover
Mounting
Screw
Cover
Mounting
Screw
Location
Rear
Chassis
Handle
Location
loudspeaker
terminals, it is mandatory to use banana plugs
inserted into the top hole of the loudspeaker
terminals in order to comply with safety stan-
dard requirements.
Connection Method for use inside the United States and
Canada only:
Attach the previously prepared bare wire cable ends into
the banana plugs and secure the connections. Insert the
banana plug only into the hole at the top of the terminal.
Cable
Openings
Figure 7a (Inside USA and Canada)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect for Bi-Amp
McIntosh Preamplifier
Connect to
AC Outlet
Connect to
AC Outlet
McIntosh
Amplifier
Two
McIntosh
Amplifier
One
Terminal
Connections
Cover
Cover
Mounting
Screw
Cover
Mounting
Screw
McIntosh
Loudspeaker
Rear
Chassis
Handle
Location
Location
Cable
Openings
Figure 7b (Outside USA and Canada)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Displays and Switches
Meter indicates the Power
Output of the Amplifier
LED indicates when Amplifier
POWER GUARD circuit activates
Standby Power On
Indicator
METER Switch selects
the display modes of the
Power Output Meter and
Meter Illumination
POWER Switch Turns
AC Power On/Off, or
On/Remote
12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Operate
How to Operate
Power On
electronically held to this power level until
a higher power peak passes through the
amplifier. The meter pointer will then rise
to the newer higher indication. If no further
power peaks are reached, the meter pointer
will very slowly return to its rest position or
lower power level. The decay rate is approxi-
mately 6dB per minute.
Note: The MC1.2KW Power Output Meter
indicates the actual wattage delivered
to the loudspeakers by responding to
the combination of current and voltage
output.
To have the MC1.2KW automatically turn On or Off when
a control center turns on or off, rotate the power switch to
the remote position. For manual opera-
tion, rotate the power switch to the
On or Off position as desired. Refer to
figure 8.
Note: There must be a power control
connection between the MC1.2KW
and the McIntosh Control Center,
Figure 8
in order for the remote power
turn-on to function.
Meter Selection
Rotate the meter mode switch to select the meter operation
mode you desire. Refer to figures
9 and 10.
Input Mode Switch
The Input Mode Switch, which is located on the Rear Panel
of the MC1.2KW, allows
Lights Off - Meter lights are
turned off and the
you to select either the
Balanced or Unbalanced
Input. Refer to figure 11.
Figure 11
meter will contin-
ue to indicate the
power output.
Note: When Power
Figure 9
Control
Input of the MC1.2KW is connected to a
McIntosh A/V Control Center or Pream-
plifier with Remote Meter Illumination
Control, the Meter Illumination will
automatically be remotely controlled
(On/Off) with the METER Switch to set
to the WATTS or HOLD position.
Watts- The meters respond to all the musical in-
formation being produced by the amplifier.
They indicate to an accuracy of at least 95%
of the power output with only a single cycle
of a 2000Hz tone burst.
Figure 10
Hold - The meter pointer is locked to the highest
power peak in a sequence of peaks. It is
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Description
McIntosh Laboratory, the company who introduced the
world’s first amplifier that could be called “High Fidel-
ity”, has done it again. The McIntosh engineering staff has
created a power amplifier without compromise, using the
most advanced McIntosh circuit design concepts.
watts and with an output current of 200 amperes, makes
this not only the most advanced, but also the most pow-
erful amplifier McIntosh has ever manufactured. The
distortion limits for the MC1.2KW are no more than
0.005% at rated power output for all frequencies from
20Hz to 20,000Hz. Typical performance at mid frequen-
A continuous average power output rating of 1,200
Top View of the MC1.2KW
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Description
cies is less than 0.002%. The true distortion readings
on the MC1.2KW are so low, it takes special measuring
techniques to make accurate readings. The MC1.2KW can
deliver the best possible performance from any type of
high quality loudspeaker system.
active region safe operating area. An automatic tracking
bias system completely eliminates any trace of crossover
distortion. Precision metal film resistors and low dielectric
absorption film capacitors are used in all critical circuit
locations.
Creating an amplifier with this level of performance did
not come easily. Many months of design, testing and mea-
suring were required. Extensive controlled listening tests,
The output signals of the two balanced circuits are
coupled together in the unique McIntosh MC1.2KW Out-
put Autoformer. It provides low distortion power transfer
the ultimate form of measuring, were made before the final at frequencies from below 20Hz to well beyond 20,000Hz
design was accepted.
with optimum impedance points of two ohms, four ohms
and eight ohms. The unequaled expertise of McIntosh in
Design Philosophy
the design and manufacturing of autoformers is legendary
The design philosophy incorporated in the MC1.2KW
involved several different techniques, all based on sound
scientific logic. Every stage of voltage or current ampli-
fication must be as linear as possible prior to the use of
negative feedback. McIntosh engineers know how to prop-
erly design negative feedback circuits so they contribute to
the extremely low distortion performance expected from
a McIntosh amplifier. The typical McIntosh owner would
never accept the approximately 100 times higher distortion
of many non-feedback designs.
in the high fidelity industry.
The
high ef-
ficiency
circuit de-
sign of the
MC1.2KW
contrib-
utes to low
operating
Double Balanced Push-Pull design is used from input to tempera-
output. Each half of the amplifier contains complimentary
balanced circuitry. The resulting double balanced configu-
ration cancels even order distortion. Refer to figure 12.
All transistors are selected to have nearly constant
current gain over the entire current range they must cover.
Output transistors in particular, have matched uniform
current gain, high current bandwidth product and large
tures. More
than 2800
square
inches of
heat sink
Figure 13
area keep the MC1.2KW operating safely with convection
cooling. No fans are needed. Refer to figure 13.
Block Diagram
of the
Power Amplifier
(one channel shown)
Figure 12
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Autoformers
tone burst at
2kHz. Refer
to figure
15. Voltage
and current
outputs are
electronical-
ly measured,
multiplied
and fed to
All solid state power amplifier output circuits work best
into what is called an optimum load. This optimum load
may vary considerably from what a loudspeaker requires.
In the case of more than one loudspeaker connected in
parallel, the load to the power amplifier may drop to two
ohms or even less. A power amplifier connected to a load
that is lower than optimum, causes more output current
to flow, which results in extra heat being generated in
the power output stage. This increase in temperature will
result in a reduced life expectancy for the amplifier.
The special Balanced Dual Core Autoformer creates an
ideal match between the power amplifier output stage and
the loudspeaker. A McIntosh amplifier with an Autoformer
can be used to safely drive multiple speakers without
reducing the life expectancy of the power amplifier. Refer
to figure 14.
a special
circuit that
accelerates
Figure 15
the pointer movement in the upward direction. When the
pointer reaches its peak it pauses only long enough for the
human eye to perceive its position, then drops. It is almost
10 times faster than a professional VU meter.
A front panel switch is provided to change the meter to
the Watts Hold Mode of operation. This allows fast upward
movement of the pointer but greatly increases Hold Time
at the peak of its travel. The highest power output of the
source material is thus recorded.
Protection Circuits
The MC1.2KW incorporates a version of the McIntosh
Sentry Monitor Output
Transistor Protection
Circuit. Refer to Fig-
ure 16. There is abso-
lutely no compromise
in sonic performance
Normal Operating Area�
with this circuit, and it
ensures safe operation
of the amplifier under
even the most extreme
operating conditions.
The different types of
Sentry Monitor�
Safety Area�
Output�
Transistor�
Failure�
Figure 14
Figure 16
There is absolutely no performance limitation with an
Autoformer. Its frequency response exceeds that of the
output circuit itself, and extends well beyond the audible
range. Its distortion level is so low it is virtually impossible
to measure.
In the rare event of a power amplifier output circuit fail-
ure, the McIntosh Autoformer provides absolute protection
from possible damage to your valuable loudspeakers. The
unequaled expertise of McIntosh in the design and manu-
facturing of Autoformers is legendary in the high fidelity
industry. McIntosh engineers know how to do it right.
protection circuits incorporated in the MC1.2KW insure a
long and safe operating life. This is just one of the many
characteristics of McIntosh
Power Amplifiers that make
them world famous.
Input Test Signal
The MC1.2KW also
includes the unique pat-
ented McIntosh Power Guard
circuit. Power Guard elimi-
nates the possibility of ever
overdriving the amplifier
into clipping. Refer to figures
17, 18 and 19. An overdriven
amplifier can produce both
Power Output Meter
The McIntosh MC1.2KW has a huge hand built Output
Watt Meter that responds 95% full scale to a single cycle
Figure 17
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Description, con’t
audible and inaudible distor-
tion levels exceeding 40%.
The audible distortion is
of the two
amplifier
circuits,
Without Power Guard
unpleasant to hear, but the
inaudible ultrasonic distortion
is also undesirable, since it can
damage valuable loudspeaker
system tweeters. You will
never experience the harsh
and damaging distortion due
to clipping.
allowing
each ampli-
fier cir-
cuit to be
optimized
using its
own power
supply.
The Power Guard circuit is
a waveform comparator, moni-
toring both the input and out-
put waveforms. Under normal
operating conditions, there
are no differences between
the shape of these waveforms.
If an amplifier channel is
overdriven, there will be a
difference between the two
signal waveforms. When the
difference exceeds 0.3%,
the Power Guard activates
the PG light and a dynamic
electronic attenuator at the
amplifier input reduces the
input volume just enough to prevent any further increase
in distortion. The Power Guard circuit acts so fast that
there are absolutely no audible side effects and the sonic
purity of the music reproduction is perfectly preserved.
The MC1.2KW Power Amplifier with Power Guard is not
limited to just the rated power output, but will actually
produce distortion free output well above its rated power
due to the McIntosh philosophy of conservative design.
Refer to
figure 20.
High power
Figure 21
Figure 18
amplifiers draw high current from the AC power line. The
very large Power Transfomer, has toroidal windings on a
toroidal core and can supply over 35 amps of continuous
current. Refer to figure 21 (golf ball is for size compar-
sion). It is enclosed in the legendary McIntosh Potted
Enclosures and weighs over 12.06kg. The super size main
filter capacitors can store over 600 Joules of energy for the
five amplifier channels, necessary for the wide dynamic
range that “Digital Audio” demands. The power amplifier
draws high current from the AC power line. Therefore, it is
important that they plug directly into the wall outlet.
Also, most owners desire one power switch for the whole
audio system. The MC1.2KW is equipped with a circuit
that provides remote Power Control from a McIntosh
A/V Control Center. When the A/V Control Center is
switched On, a (+5V) signal operates the power relay in
the MC1.2KW. The MC1.2KW also has a remote Power
Control Out Jack. The Power Control signal from this jack
is delayed by a fraction of a second so that the turn on
power surge of the next power amplifier occurs at a later
time. This helps prevent power circuit overload that could
trip circuit breakers or blow fuses, a very important feature
in a high power Home Theater System employing three or
more MC1.2KW Power Amplifiers.
With Power Guard
Figure 19
Power Supply Circuits
To compliment the fully balanced design of the MC1.2KW
there are two high voltage power supplies; one for each
CIRCUIT
BREAKER
Block Diagram
of the
Power Supply
Figure 20
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
Power Output
Power Requirements
Minimum sine wave continuous average power output is:
1,200 watts into 2 ohm load
1,200 watts into 4 ohm load
100 Volts, 50/60Hz at 15 Amps
110 Volts, 50/60Hz at 12.5 Amps
120 Volts, 50/60Hz at 12 Amps
220 Volts, 50/60Hz at 7.5 Amps
230 Volts, 50/60Hz at 6.5 Amps
240 Volts, 50/60Hz at 6.5 Amps
Standby: 0.5 watts
1,200 watts into 8 ohm load
Output Load Impedance
2, 4 or 8 ohms
Note: Refer to the rear panel of the MC1.2KW for the correct
voltage.
Rated Power Band
20Hz to 20,000Hz
Overall Dimensions
Width is 17-3/4 inches (45.09cm)
Height is 12-5/16 inches (31.27cm) including feet
Depth is 22 inches (55.88cm) including the Front Panel and
Cables
Total Harmonic Distortion
0.005% maximum harmonic distortion at any power level
from 250 milliwatts to rated power, 20Hz to 20,000Hz
Dynamic Headroom
2dB
Weight
147 pounds (66.7 kg) net, 172 pounds (78.0 kg) in shipping
carton
Frequency Response
+0, -0.25dB from 20Hz to 20,000Hz
+0, -3dB from 10Hz to 100,000Hz
Shipping Carton Dimensions
Width is 31 inches (78.74cm)
Depth is 28 inches (71.12cm)
Height is 17-1/4 inches (43.82cm)
Input Sensitivity (for rated output)
2.5 Volt Unbalanced
5 Volt Balanced
Signal To Noise Ratio (A-Weighted)
120dB below rated output, Unbalanced
124dB below rated output, Balanced
Intermodulation Distortion
0.005% maximum, if the instantaneous peak power output
does not exceed twice the rated power output for any com-
bination of frequencies from 20Hz to 20,000Hz.
Wide Band Damping Factor
Greater than 40
Input Impedance
10,000 ohms
Power Guard
Less than 2% THD with up to 14dB overdrive at 1,000Hz
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing Instructions
Packing Instructions
In the event it is necessary to repack the equipment for
shipment, the equipment must be packed exactly as shown
below. It is very important that the four feet are attached to
the bottom of the equipment. This will ensure the proper
equipment location on the bottom foam pad. Failure to do
this will result in shipping damage.
Quantity Part Number Description
1
1
2
3
034105
034104
034349
034350
Shipping carton top
Shipping carton bottom
Foam Pad (top and bottom)
Foam Ring
Use the original shipping carton and interior parts only
if they are all in good serviceable condition. If a shipping
carton or any of the interior part(s) are needed, please call
or write Customer Service Department of McIntosh Labo-
ratory. Please see the Part List for the correct part numbers.
4
4
400159
018445
10-32 x 3/4 inch screw
Feet
19
Download from Www.Somanuals.com. All Manuals Search And Download.
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, NY 13903
The continuous improvement of its products is the
policy of McIntosh Laboratory Incorporated who
reserve the right to improve design without notice.
Printed in the U.S.A.
McIntosh Part No. 04105500
Download from Www.Somanuals.com. All Manuals Search And Download.
|