Loudspeaker System
XCS1K
Owner’s Manual
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank You
Table of Contents
Your decision to own this McIntosh XCS1K Loudspeaker
System ranks you at the very top among discriminating
music listeners. You now have “The Best.” The McIntosh
dedication to “Quality,” is assurance that you will receive
many years of listening enjoyment from this unit.
Please take a short time to read the information in this
manual. We want you to be as familiar as possible with all
the features and functions of your new McIntosh.
Safety Instructions............................................................2
Thank You and Please Take a Moment.............................3
Technical Assistance and Customer Service....................3
Table of Contents and General Information .....................3
Introduction.......................................................................4
Performance Features .......................................................5
Dimensions ....................................................................6-7
Installation ........................................................................8
How to Connect using a single Amplifier ........................ 9
How to Connect using two Amplifiers.......................10-11
How to Connect using three Amplifiers.................... 12-13
Specifications.................................................................. 14
Packing Instruction.........................................................15
Please Take A Moment
The serial number, purchase date and McIntosh Dealer
name are important to you for possible insurance claim or
future service. The spaces below have been provided for
you to record that information:
General Information
Serial Number: __________________________________
Purchase Date: __________________________________
Dealer Name: ___________________________________
Caution: The XCS1K weight is 133 pounds (60.3kg). It re-
quires two or more persons to safely handle the Loudspeaker
System.
1. Loudspeaker Cables of adequate size are important to en-
sure that there will be no significant power loss or heating.
Cable size is specified in Gauge numbers or AWG (Ameri-
can Wire Gauge). The smaller the Gauge number, the larger
the wire size:
If the Loudspeaker Cables are 50 feet (38.1m) or less,
use at least 12 Gauge (AWG) wire size or larger.
If the Loudspeaker Cables are 100 feet (76.2m) or less,
use at least 10 Gauge (AWG) wire size or larger.
2. For additional connection information, refer to the owner’s
manual(s) for any component(s) connected to the XCS1K
Loudspeaker.
Technical Assistance
If at any time you have questions about your McIntosh
product, contact your McIntosh Dealer who is familiar
with your McIntosh equipment and any other brands that
may be part of your system. If you or your Dealer wish
additional help concerning a suspected problem, you can
receive technical assistance for all McIntosh products at:
3. The XCS1K’s built-in speaker protection incorporates five
automatic resetting solid-state devices in the crossover
networks. One protects the tweeters, one for the midranges
and three for the woofers. The protection allows a certain
amount of overdrive but extended periods will trigger pro-
tection. If an obvious lack of high, mid or low frequencies
is noticed, the Protection Device may have activated. These
devices will automatically reset when the volume level is
reduced significantly and kept low until the output of the
affected Loudspeaker Element returns to normal.
4. When the XCS1K Loudspeaker System is driven by more
than one amplifier, the output levels of the different ampli-
fiers connected to the Loudspeaker System must be adjusted
to achieve a proper balance between the low, midrange
and high frequencies reproduced. This adjustment is best
achieved through the use of audio test equipment operated
by a qualified installer.
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, New York 13903
Phone: 607-723-1545
Fax: 607-724-0549
Customer Service
If it is determined that your McIntosh product is in need of
repair, you can return it to your Dealer. You can also return
it to the McIntosh Laboratory Service Department. For
assistance on factory repair return procedure, contact the
McIntosh Service Department at:
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, New York 13903
Phone: 607-723-3515
Fax: 607-723-1917
Copyright 2008 © by McIntosh Laboratory, Inc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The new McIntosh XCS1K Loudspeaker System is a
Center Channel Loudspeaker capable of reproducing the
full dynamic range of a symphony orchestra with very low
audible distortion. It is the perfect match to the famous
XCS1K Column Loudspeakers, when used in a Home
Theater/Music System. It uses the same acoustic technol-
ogy found in the XCS1K Column Loudspeakers developed
by the McIntosh Acoustic Engineers. The technology has
been refined over the years and is now the 6th generation
of the design and provides superior quality sound repro-
duction in a full range system.
The XCS1K Loudspeaker utilizes
a Horizontal Arc Array Design
with three-quarter inch Titanium
Dome Tweeters and multiple
rows of two inch Midrange
Inverted Titanium Dome Driv-
ers. Refer to figures 1, 2A and
2B. The Sound Waves from this
Analysis and testing
resulted in a design con-
cept which utilizes a pair
of aluminum shorting
sleeves in the magnetic
circuit. Refer to figure
4. The sleeves virtually
eliminate the negative
influence of the fluctuat-
ing voice coil field on
the permanent magnet
field. This results in
lower distortion due to
more linear magnetic
flux in the voice coil
gap. Refer to figure 5.
Additional benefits are
less volume compression
due to improved heat
transfer through the sleeves and a
cooler operating voice coil. Both
measurements, as well as critical
listening, reveal ten times less
distortion than previous designs.
A good example of this low dis-
tortion is incredible smoothness
and clarity in the reproduction of
the human voice.
Figure 3
Horizontal Arc Array produce a
Figure 1
stable and focused sym-
metrical horizontal sound
image. Since the audio
power fed to each row
is distributed among all
the drivers, each driver
does not have to work as
hard, resulting in greater
power handling capa-
bility, greatly reduced
power compression and
Figure 4
The
Crossover
Networks
a dramatic reduction in
distortion.
used in the
XCS1K
Figure 2A
Loudspeak-
er System
are phase
matched
between
the Low
Frequency,
Midrange
Figure 5
Figure 2B
and High Frequency Sections to ensure a smooth frequen-
cy response over the entire audible range. Refer to figures
6, 7 and 8. The crossover inductors are selected so they
will not add audible distortion. The network capacitors are
film type for extra reliability. All the Capacitors and In-
ductors are chosen for high current capacity. Each section
of the network utilizes its own self resetting high current
PPTC type fuses to provide an extra measure of protection.
The Low Frequency Section of the System consists of
two 10 inch Woofers. They have a large magnet assembly
and long cone excursions with very low levels of harmonic
distortion and frequency response down to 16Hz. Refer to
figure 3. The Woofer also incorporates McIntosh’s Pat-
ented LD/HP1 Magnetic Circuit Design. Finite Element
1LD/HP Pat. No 5,151,943
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction and Performance Features
Performance Features
• Patented LD/HP Technology
The McIntosh Low Frequency Loudspeaker Elements
feature the patented LD/HP Magnetic Circuit Design.
This design, when compared to conventional Loudspeaker
Elements, reduces distortion significantly. It also increases
power handling and efficiency.
• Neodymium-Iron-Boron Alloy Magnets
The 32 two inch Midranges and 20 three-quarter inch
Dome Tweeters all use this Alloy. The Neodymium-
Iron-Boron Alloy has the highest flux density per unit
of volume. The smaller overall size of the Midrange and
Tweeter Loudspeakers allows for closer spacing and results
in improved sound reproduction.
• Low Harmonic and Intermodulation Distortion
The XCS1K Loudspeaker System is capable of reproducing
the full dynamic range of a symphony orchestra with very
low audible distortion of any kind.
Figure 6
• High Power Handling
The Loudspeaker Elements and Crossover Components of
the XCS1K are all chosen for use with powerful amplifiers
up to 1,200 watts.
• Superior Imaging
Locating the Tweeters between the two rows of Midranges
generates a symmetrical response for superior imaging.
Figure 7
• Versatile Operation and Placement
In addition to the regular connections, the XCS1K Loud-
speaker System provides separate connections for Bi-Am-
plification and Tri-Amplification hookups.
• Extruded Column
The top, bottom and rear of the XCS1K Low Frequency
enclosure is extruded thick aluminum construction with
non-parallel internal sides and is given a High Gloss Black
Piano Type Finish.
• Gold Plated Input Connectors
The XCS1K input connectors are gold plated for superior
corrosion resistance and high electrical conductivity.
Figure 8
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
The following dimensions can assist in determining the
best location for your XCS1K Loudspeaker System.
Front View of the
XCS1K
Loudspeaker System
16-7/8"
42.9cm
39-1/4"
99.7cm
Side View of the
XCS1K
Loudspeaker System
(shown at maximum
elevation of 30°)
21"
53.3cm
22-1/8"
56.2cm
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
7-5/16"
18.5cm
13-1/2"
31.8cm
3-3/4"
9.5cm
Rear View of the XCS1K
Loudspeaker System
5-5/8"
14.3cm
Front View of the XCS1K
Midrange and High Frequency Horizontal Array
1-3/4"
4.45cm
3-7/8"
9.8cm
13-1/8"
33.3cm
11-5/16"
28.7cm
9-1/2"
24.1cm
2-3/16"
5.56cm
4"
10.2cm
Front View of the XCS1K
Low Frequency Horizontal Array
11-5/16"
28.7cm
21-3/4"
55.2cm
8-3/4"
22.3cm
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
Location in the Room
3. Lift off the top of the shipping carton and set it aside.
4. Remove the smaller inner carton labeled XCS1K
Cradle.
5. Open the inner carton, remove the Cradle and place it
in the final location of the XCS1K Loudspeaker. Refer
to figure 11.
The XCS1K Loudspeaker is designed for use as a Center
Channel in a Home Theater System. The optimal method
for selecting all the Loudspeaker Locations in a Home
Theater System includes the use of a real time spectrum
analyzer operated by an experienced system installer. An
uncompromising installation would take into consideration
the floor, wall and ceiling coverings, the type and place-
ment of furniture and can even include the architectural
design of the room and its construction materials. In those
instances where placement in the room is fixed, an en-
vironmental equalizer may be needed to restore proper
musical balance.
6. Remove the Top Foam from
the Loudspeaker.
7. Remove the Loudspeaker
from the Bottom Foam.
Cradle
(Top View)
8. Remove the Blue Protective
Cloth Cover from the Loud-
speaker. Set the Loudspeaker
and Cover aside on the previ-
ously prepared area.
Figure 11
The XCS1K Loudspeaker’s Smooth Frequency Re-
sponse may be altered by
a large object(s) located
in the path of the sound
Adjusting the Elevation of the Loudspeaker
waves or by locating the
Loudspeaker too close to
a side wall. There should
be an unobstructed area
The acoustic output of the XCS1K Loudspeaker may be
directed to line up with the height of the average ear in the
prime viewing/listening area. There is a 30 degree range of
Locking
adjustment built-in.
Screws
in front of the XCS1K
1. Using an approprate tool,
Loudspeaker on either
side of the center axis for
the best performance. The
optimum location in a
Home Theater System is
directly under or in front
of the TV/Monitor. Refer
to figures 9 and 10.
Figure 9
loosen the hex head screws
on the insides of the XCS1K
Cradle. Refer to figure 12.
Height
Adjustment
Screws
2. Before placing the XCS1K
Loudspeaker on the Cradle,
Figure 12
rotate the top/sides of the
Cradle to the desired angle so
the sound will be directed toward ear level when seated
in the main view-
Figure 10
ing/listening area.
Unpacking the Loudspeaker
4. Tighten the height
To protect the fine finish of the XCS1K Loudspeaker Sys-
tem during the assembly process, it is advisable to prepare
a suitable area. A freshly vacuumed carpeted area covered
with a soft, clean fabric, such as a large bed linen or blan-
ket would be suitable. Start by unpacking the Loudspeaker.
It is recommended that the Professionals at your McIn-
tosh Dealer, who are skilled in all aspects of installation
and operation, install the XCS1K Loudspeaker System and
any associated audio equipment.
adjustment and
locking screws on
the insides of the
Cradle.
Top View of
Lift Areas
Figure 13
5. Refering to the lift
areas in figure 13, lift up on
the sides and center rear of
the Loudspeaker with two or
more persons. Place the Loud-
speaker on the Cradle. Refer
to figure 14.
Note: When lifting up on the
sides of the Loudspeaker,
be carefull as to not
CAUTION: The XCS1K Loudspeaker weighs 133 pounds
(60.3 kgs). It requires two or more persons to
safely handle during assembly, adjustment and
placement in the room.
1. Orient the XCS1K shipping carton with the arrows on
the outside of the carton pointing upward.
2. Remove the banding material from the shipping carton.
remove the detachable
sides.
6. Proceed to “How to connect” starting on page 9.
Figure 14
8
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect using a single Amplifier
How to Connect using a single Amplifier
Caution: The AC Power Cord should not be connected to the
Power Amplifier until after the Loudspeaker Con-
nections have been made. Failure to observe this
could result in Electric Shock.
1. Prepare Loudspeaker cables by choosing one of the
methods below:
Figure 18
Figure 19
Figure 20
2. Connect a Loudspeaker cable from the XCS1K LOW
Frequency COM (-) Binding Post to the (-) Binding
Post of the Power Amplifier.
Bare wire cable ends:
Carefully remove sufficient insulation from the
cable ends, refer to figures 15, 16 & 17. If the cable
is stranded, carefully twist the strands together as
tightly as possible.
Notes: 1. It is important to maintain the correct polarity
at both ends of the Loudspeaker cables.
2. For proper operation the metal jumpers must
be installed between the Loudspeaker Terminal
Posts as illustrated.
3. Connect a Loudspeaker cable from the XCS1K LOW
Frequency 8Ω (+) Binding Post to the (8 ohm) Binding
Post of the Power Amplifier.
Figure 16
Figure 17
Figure 15
4. Tighten all of the Loudspeaker and Amplifier Binding
Posts.
Note: If desired, the twisted ends can be tinned with
solder to keep the strands together or attach
spade lugs.
McIntosh Power Amplifier
Spade lug or prepared wire connection:
Insert the spade lug connector or prepared section
of the cable end into the terminal side access hole,
and tighten the terminal cap until the cable is firmly
clamped into the terminal so the wires cannot slip
out. Refer to figures 18, 19 & 20.
Jumpers
-
+
Jumpers
9
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect using two Amplifiers
Caution: The AC Power Cord should not be connected to the
Power Amplifier until after the Loudspeaker Con-
nections have been made. Failure to observe this
could result in Electric Shock.
Post of the Power Amplifier number one.
6. Connect a Loudspeaker cable from the XCS1K MID
Frequency COM (-) Binding Post to the (-) Binding
Post of the Power Amplifier number two.
7. Connect a Loudspeaker cable from the XCS1K MID
Frequency 8Ω (+) Binding Post to the (8 ohm) Binding
Post of the Power Amplifier number two.
8. Tighten all of the Loudspeaker and Amplifier Binding
Posts.
1. Prepare Loudspeaker cables by choosing one of the
methods below:
Bare wire cable ends:
Carefully remove sufficient insulation from the
cable ends, refer to figures 15, 16 & 17. If the cable
is stranded, carefully twist the strands together as
tightly as possible.
McIntosh Power Amplifier number one
Figure 16
Figure 17
Figure 15
Note: If desired, the twisted ends can be tinned with
solder to keep the strands together or attach
spade lugs.
Spade lug or prepared wire connection:
Insert the spade lug connector or prepared section
of the cable end into the terminal side access hole,
and tighten the terminal cap until the cable is firmly
clamped into the terminal so the wires cannot slip
out. Refer to figures 18, 19 & 20.
Figure 18
Figure 19
Figure 20
2. Remove the metal jumper between the Loudspeaker
LOW Frequency COM (-) Binding Post and MID Fre-
quency COM (-) Binding Post.
3. Remove the metal jumper between the Loudspeaker
LOW Frequency 8Ω (+) Binding Post and MID Fre-
quency 8Ω (+) Binding Post.
4. Connect a Loudspeaker cable from the XCS1K LOW
Frequency COM (-) Binding Post to the (-) Binding
Post of the Power Amplifier number one.
Notes: 1. It is important to maintain the correct polarity
at both ends of the Loudspeaker cables.
2. For proper operation the metal jumpers must
be installed between the Loudspeaker Terminal
Posts as illustrated.
5. Connect a Loudspeaker cable from the XCS1K LOW
Frequency 8Ω (+) Binding Post to the (8 ohm) Binding
10
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect using two Amplifiers
McIntosh Power Amplifier number two
Jumper
Jumper
-
-
+
+
11
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect using three Amplifiers
Caution: The AC Power Cord should not be connected to the
Power Amplifier until after the Loudspeaker Con-
nections have been made. Failure to observe this
could result in Electric Shock.
8. Connect a Loudspeaker cable from the XCS1K HIGH
Frequency COM (-) Binding Post to the (-) Binding
Post of the Power Amplifier number three.
9. Connect a Loudspeaker cable from the XCS1K HIGH
Frequency 8Ω (+) Binding Post to the (8 ohm) Binding
Post of the Power Amplifier number three.
10. Tighten all of the Loudspeaker and Amplifier Binding
Posts.
1. Prepare Loudspeaker cables by choosing one of the
methods below:
Bare wire cable ends:
Carefully remove sufficient insulation from the
cable ends, refer to figures 15, 16 & 17. If the cable
is stranded, carefully twist the strands together as
tightly as possible.
McIntosh Power Amplifier number one
Figure 16
Figure 17
Figure 15
Note: If desired, the twisted ends can be tinned with
solder to keep the strands together or attach
spade lugs.
Spade lug or prepared wire connection:
Insert the spade lug connector or prepared section
of the cable end into the terminal side access hole,
and tighten the terminal cap until the cable is firmly
clamped into the terminal so the wires cannot slip
out. Refer to figures 18, 19 & 20.
Figure 18
Figure 19
Figure 20
2. Remove all four metal jumpers between Loudspeaker
Binding Posts.
4. Connect a Loudspeaker cable from the XCS1K LOW
Frequency COM (-) Binding Post to the (-) Binding
Post of the Power Amplifier number one.
Note: It is important to maintain the correct polarity
at both ends of the Loudspeaker cables.
5. Connect a Loudspeaker cable from the XCS1K LOW
Frequency 8Ω (+) Binding Post to the (8 ohm) Binding
Post of the Power Amplifier number one.
6. Connect a Loudspeaker cable from the XCS1K MID
Frequency COM (-) Binding Post to the (-) Binding
Post of the Power Amplifier number two.
7. Connect a Loudspeaker cable from the XCS1K MID
Frequency 8Ω (+) Binding Post to the (8 ohm) Binding
Post of the Power Amplifier number two.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect using three Amplifiers
McIntosh Power Amplifier number two
McIntosh Power Amplifier number three
-
-
-
+
+
+
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
General Specifications
System Driver Complement
Two 10 inch LD/HP Woofers
Thirty-Two 2 inch Titanium Inverted
Dome Midranges
Finish Enclosures
High Gloss Black
Finish Grille
Twenty 3/4 inch Titanium Dome Tweeters
Black Knit Cloth with High Gloss Black Trim
Impedance
Overall Dimensions
8 ohms Nominal
Width is 39-1/4 inches (99.7cm)
Height is 21 inches (53.3cm)
Depth is 22-1/8 inches (56.2cm)
Frequency Response
16Hz - 45kHz
Weight
Sensitivity
86dB (2.8V/1m equivalent)
133 pounds (60.3 kg) Loudspeaker net
15 pounds (6.8 kg) Cradle net
178 pounds (80.7 kg) in shipping carton
Crossover Frequencies
250Hz
1,500Hz
Shipping Carton Dimensions
Width is 28 inches (71.1cm)
Depth is 20 inches (50.8cm)
Height is 58 inches (147.3cm)
Power Handling
1,200 Watts Maximum
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing Instructions
Packing Instructions
In the event it is necessary to repack the equipment for
shipment, the equipment must be packed exactly as shown
below. To protect the finish of the Loudspeaker it is advis-
able to place it in the original protective cotton blue cover
before placing it into the shipping carton.
Use the original shipping carton and interior parts only
if they are all in good serviceable condition. If a shipping
carton or any of the interior part(s) are needed, please call
or write Customer Service Department of McIntosh Labo-
ratory. Please see the Part List for the correct part numbers.
Quantity Part Number
Description
1
1
2
1
1
1
034431
034432
034433
034430
034434
033085
Top shipping carton
Bottom shipping carton
Top and bottom foam
Blue Protective cloth cover
Cradle carton
Bubble pack
TOP
SHIPPING
CARTON
BUBBLE
PACK
TOP
FOAM
BLUE PROTECTIVE
CLOTH COVER
CRADLE
CARTON
BOTTOM
FOAM
BOTTOM
SHIPPING
CARTON
15
Download from Www.Somanuals.com. All Manuals Search And Download.
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, NY 13903
The continuous improvement of its products is the
policy of McIntosh Laboratory Incorporated who
reserve the right to improve design without notice.
Printed in the U.S.A.
McIntosh Part No. 04107900
Download from Www.Somanuals.com. All Manuals Search And Download.
|