Model MC1375
Modelo MC1375
Modéle MC1375
Canister Steam System
Sistema A Vapor Con Depósito
Nettoyeur-Chariot À Vapeur
Owner’s Guide
Guía del Usuario
Mode D’emploi
English p. 2
Español p. 22
Français p. 42
KEEP YOUR RECEIPT FOR WARRANTY PURPOSES
Please read all instructions before use.
GUARDE SU RECIBO A EFECTOS DE LA GARANTÍA
Lea todas las instrucciones antes de usarlo.
GARDEZ VOTRE REÇU AUX FINS DE LA GARANTIE
Veuillez lire toutes les instructions avant l’utilisation.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of electrical shock, this appliance has a three-
pronged plug. This plug will fit in a polarized wall outlet only one way. If the plug
does not fit fully in the outlet, contact a licensed electrician to install a proper
outlet. DO NOT attempt to modify the plug or defeat this safety feature.
!
11. The Canister Steam System is only meant to be used with recommended Canister Steam
System accessories. Other types of attachments are not to be used with the Canister Steam
System. Doing so may cause injuries or damage to unit.
12. Attachments become hot during use. To avoid injuries, DO NOT touch attachments while us-
ing this appliance. DO NOT attempt to change attachments while unit is emitting steam.
13. When filling your Canister Steam System, only water should be used in unit. Other cleaning
agents will damage unit and can cause injuries.
14. DO NOT operate unit if steam opening is blocked. Should this occur, immediately cease us-
age and unplug from electrical outlet.
15. Store your Canister Steam System in a cool, dry place.
16. To avoid burns from escaping steam when removing Boiler Cap to refill unit:
• Always allow unit to cool for 20 minutes.
• Press and hold Steam Button to release ALL remaining steam.
SAVE THESE INSTRUCTIONS
fOR HOUSEHOld USE ONly
Questions or comments?
1-800-711-6617
•
•
•
|
ENGLISH
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
These features and accessories are included with your Canister Steam System. To obtain
additional parts, refer to Product Support on Page 19 of this manual.
UNIT FEATURES
1
2
3
4
5
6
7
8
9
10' Steam Hose
Pressure Gauge
Boiler Cap
Steam Handle Cradle
Illuminated On/Off Switch
Steam Nozzle
Steam Trigger Lock
Steam Trigger
1
4
Steam Adjustment Knob
2
9
6
3
7
5
8
|
4
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
• The 10' Steam Hose (1) safely channels the flow of steam from the Boiler to the Steam
Nozzle.
• The Pressure Gauge (2) measures the pressure in the Boiler.
is designed to safely contain steam inside the Boiler. The Boiler Cap must
• The Boiler Cap (3)
be unscrewed and removed in order to fill the Boiler with water.
functions as a convenient holder for the Steam Nozzle.
• The Steam Handle Cradle (4)
illuminates when the unit is powered On.
• The Illuminated On/Off Switch (5)
emits a flow of hot, penetrating steam whenever the Steam Trigger is
• The Steam Nozzle (6)
pressed and held.
locks Steam Trigger to "on" position for continuous steam.
• The Steam Trigger Lock (7)
is pressed and held in order to start the flow of steam from the Steam
• The Steam Trigger (8)
Nozzle, then released when you wish to stop.
adjusts steam intensity.
• The Steam Adjustment Knob (9)
|
ENGLISH
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
ACCESSORIES
2
11
1
2
3
4
5
6
7
8
9
2 - 16.5" Extension Wands
Microfiber Mop Pad
Scrubbing Mop Pad
5.5" Jet Nozzle
Triangle Brush
Large Brush
2 - 1.5" Nylon Utility Brushes
1.5" Brass Utility Brush
Angled Nozzle
Microfiber Mop Pad
12
A1375-100
13" x 8.5" Large Mop Head
A1375-003-A
3
Bristle Brush Attachment
A1375-004
10 3" Scraper
11 13" x 8.5" Large Mop Head
12 Bristle Brush Attachment
13 Storage Bag
Scrubbing Mop Pad
A1375-101
14 Fill Cup
15 Accessory Net
16 2.5" Round Brush
17 2 - 2.5" Round Scrub Pads
10
4
5.5" Jet Nozzle
A1230-001
3" Scraper
A1230-009
Fill Cup
A275-015
1
14
5
6
13
15
16.5" Extension
Wands
A1375-002
Accessory Net
A1375-005
4" Triangle Brush
A1230-002
6" x 4.5" Large Brush
A1230-003
Storage Bag
A1375-010
16
9
17
7
8
2.5" Round Brush
A1350-001
Angled Nozzle 2.5" Round Scrub Pads
A1375-001 A1230-007
1.5" Nylon Utility
Brushes
1.5" Brass Utility
Brush
A1230-005
A1230-006
|
6
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Information
connect to the Steam Nozzle. Used with mop attachment or
• The 16.5" Extension Wands (1)
for high or hard-to-reach places.
attach to the Mop Head, and are designed for removing scuffs and
• The Microfiber Mop Pad (2)
stains from hard floors. The Pads are reusable and machine washable.
attach to the Mop Head, and are designed for removing scuffs
• The Scrubbing Mop Pad (3)
and stains from hard floors. The Pads are reusable and machine washable.
focuses the flow of steam from the Steam Nozzle, and serves as the
• The 5.5" Jet Nozzle (4)
base to which the Utility Brushes and Angled Nozzle connect.
connects to the Steam Nozzle or Extension Wands, and is designed for
• The Triangle Brush (5)
cleaning corners and other difficult angles.
• The Large Brush (6) attaches to the Triangle Brush to cover large surfaces.
connects to the Jet Nozzle, providing extra scrubbing power for
• The 1.5" Nylon Utility Brush (7)
removing exceptionally tough dirt and stains.
connects to the Jet Nozzle and is designed for removing tough
• The 1.5" Brass Utility Brush (8)
stuck-on grease and grime from durable surfaces such as ovens and grills.
• The Angled Nozzle (9) is designed for reaching difficult angles and areas that the Straight
Nozzle may not completely reach.
• The 3" Scraper (10) attaches to the Steam Nozzle to scrape off stuck on grime.
• The 13" x 8.5" Large Mop Head (11) attaches to Extension Wands to clean garage floors,
decks or any other extra large surface areas.
• The Bristle Brush Attachment (12) attaches to Large Mop Head to scrub away stubborn spots
on floors.
• The Storage Bag (13) stores all attachments neatly on one convenient bag.
• The Fill Cup (14) is used to fill Boiler without spills.
• The Accessory Net (15) stores brushes and other small accessories.
• The 2.5" Round Brush (16) connects to the Jet Nozzle to scrub especially tough stains. The
Round Brush functions similar to the Nylon Utility Brush, only designed to more efficiently
scrub larger surface areas.
connects to the Jet Nozzle and is designed to scrub tough dirt
• The 2.5" Round Scrub Pad (17)
and scuffs from surfaces.
|
ENGLISH
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling Your Canister Steam
System
STEAM MOPPING ACCESSORIES
WARNING: Do not try to connect accessories while unit is emitting steam.
EXTENSION WANDS
1. Select one of the Extension Wands. Insert end (A) of Wand onto Steam Nozzle (B) with yellow
lock/release button slightly off center with hole. Fully insert and rotate wand slightly to allow
button to snap into hole.
2. Using the same instruction, attach remaining Extension Wand to the first Wand. Both Exten-
sion Wands should now be connected to the Steam Nozzle.
C
A
B
MOP HEAD
1. Align Mop Head with open end of Extension Wand, so that hole in Mop Head aligns with yel-
low lock/release button on Wand.
2. Press down on yellow lock/release button. While continuing to hold button down, slide Mop
Head onto Extension Wand (See figure 1-A). Fully insert and rotate wand slightly until button
snaps through hole (See figure 1-B).
NOTE: Do not use excessive force when mopping or using Extension Wands as this
may cause the Wands to break.
FIGURE 1
A
B
BRISTLE BRUSH ATTACHMENT
1. Align Mop Head with Bristle Brush Attachment, so that the re-
lease tabs (A) on the Bristle Brush align with the sides of the Mop
Head (B).
2. Firmly press the Bristle Brush Attachment onto Mop Head until it
securely snaps into place.
Note: Do not use Bristle Brush Attachment with Microfiber or
Scrubbing Mop Pad.
|
8
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling Your Canister Steam
System
MICROFIBER PADS
1. Lay one Microfiber Pad on flat surface, with two fastener strips facing upward.
2. Align Mop Head with Microfiber Pad. Make sure Mop Head is oriented with Pad as shown,
and centered as best as possible (See figure 2-A).
3. Press Mop Head firmly down onto Microfiber Pad. Fastener strips will adhere to Pad Grips on
underside of Mop Head. Pad should now be attached and ready for use (See figure 2-B).
CAUTION: Use care when handling a recently used Microfiber Pad, as it may still be hot.
NOTE: Microfiber Pads are machine washable. To avoid picking up lint, washing sepa-
rately from other fabrics is recommended. Only use liquid detergent. Avoid using any
fabric softeners or bleach. Air drying is recommended; machine drying on a low heat
or air dry setting is acceptable as well.
FIGURE 2
A
B
The Mop Head and Microfiber Pads are perfect for use on these hard floor surfaces:
Sealed Hardwood
Stained Concrete
Sealed Laminate
Linoleum
Glazed Ceramic
Granite
Marble
Vinyl
Tile
•
•
•
•
•
•
•
•
•
IMPORTANT: Do not use on unsealed hardwood or unglazed ceramic surfaces. Sur-
faces that are not properly sealed may be warped or damaged by exposure to heat and
moisture.
Care should also be taken when steaming sealed hardwood floors, as prolonged ex-
posure to steam in a single spot may cause damage and discoloration. To avoid this,
keep the Mop Head in constant motion on these surfaces.
Steam may remove the sheen from some floors that have been treated with wax.
Extremely rough textured floors may tear or damage Microfiber Pads.
Before steaming any flooring, it is recommended to consult the manufacturer’s guide-
lines. For flooring in question, always test on a small inconspicuous area before pro-
ceeding.
|
ENGLISH
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling Your Canister Steam
System
STEAM CLEANING ACCESSORIES
WARNING: Do not connect accessories while unit is emitting steam.
JET NOZZLE / SCRAPER / TRIANGLE BRUSH
1. Select one of the three accessories (Jet Nozzle shown as example) and push onto the Steam
Nozzle (A).
2. Rotate accessory until the yellow lock/release button snaps into the accessory hole (B).
NOTE: The Jet Nozzle, Scraper and Triangle Brush can be connected to the end of an
Extension Wand for reaching high or difficult spots. Connect the Extension Wand (or
Wands) as outlined on Page 8, then connect your desired accessory to the Wand in the
same way as you would normally connect to the Steam Nozzle.
A
B
Steam Nozzle
UTILITY BRUSHES / ANGLED NOZZLE / SCRUB PAD
NOTE: Accessories connect to the Jet Nozzle, not the Main Nozzle.
1. Firmly press accessories onto tip of Jet Nozzle. Press it on as far as possible to prevent
steam leakage.
2. To remove accessories, simply grip it firmly and pull it off Jet Nozzle.
|
10 ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling Your Canister Steam
System
LARGE BRUSH
NOTE: Large Brush connects to the Triangle Brush, not the Jet
Nozzle.
1. Place Large Brush over the Triangle Brush, and firmly press it on to
the Triangle Brush until it snaps into place.
2. To remove Large Brush, simply grip it firmly and pull it off of the
Triangle Brush.
ORDERING ACCESSORIES & PARTS
Replacement accessories and parts for your Canister Steam System (model MC1375) may
be ordered through our Website:
You may also contact Consumer Service directly:
[email protected] or 1-800-711-6617
|
ENGLISH 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessory Recommendations
Jet Nozzle / Angled Nozzle
Dirt, Grease, Grime, Cracks and Crevices, Golf
Clubs, Tread of Running Shoes
Triangle Brush
Large Brush
Scraper
Corners on Countertops, Bathtubs, Floors
Floors, Grout
Baked on Food, Grime, Grease, Stove Tops, Ovens
Round Scrub Pad
Countertops, Bathtubs, Sinks, Refrigerators, Ovens,
Slate
Nylon Utility Brush and Round Brush
Ovens, Stove Tops, Faucet Fixtures, Microwaves,
Sports Equipment, Tile, Grout, Refrigerators, Toys,
Door Knobs, Showers, Bathtubs, Changing Tables
Brass Utility Brush
Mop
BBQ Grills, Oven Wire Racks
Stone, Slate, Glazed Ceramic Tile, Sealed Hardwood
Stone, Slate, Grout
Bristle Brush Attachment
NOTE: Before cleaning electrical appliances, check and follow appliance manufacturer’s clean-
ing guidelines. Never apply to electrical parts.
NOTE: Some delicate surfaces, such as painted wood or stainless steel may be scratched or
damaged by the bristle of the brushes, especially the Brass Utility Brush. Use careful judgment
when deciding what surface to clean with any of the brushes. If you are unsure if a surface will
be damaged, it is recommended that you test a small inconspicuous spot before proceeding.
|
12 ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Canister Steam System
FILLING BOILER
1. Place Canister Steam System on a flat, level surface.
2. Make sure illuminated On/Off Switch is turned to “Off” and grounded power cord is unplugged
from electrical outlet.
If unit has been in use, always use the following safety precautions before
removing the Boiler cap to add water:
!
Allow unit to cool for 20 minutes or until pressure gauge is at zero.
Press and hold Steam Trigger to release ALL remaining steam.
•
•
WARNING: Failure to follow these precautions may result in burns from escaping steam
when the Boiler Cap is removed.
3. Cautiously unscrew and remove Boiler Cap.
WARNING: Water may be hot.
4. Drain any water remaining inside Boiler.
NOTE: The Boiler should be emptied after each use – this will help minimize mineral
build-up and prevent over-filling.
5. Using the Fill Cup, fill the unit with 48 oz (1,420 ml) of water.
NOTE: In order to significantly reduce mineral build-up and prolong the life of your Can-
ister Steam System, use of distilled or de-mineralized water in the unit is highly recom-
mended. Refer to Page 16 for more information about mineral build-up.
WARNING: Caution should always be used when pouring water into the Boiler. Do not
look directly down into fill hole when filling. Keep your free hand and any children or
pets at a safe distance.
6. Replace Boiler Cap, ensuring that it is screwed on tightly to prevent hot steam from escaping
and causing injury.
|
ENGLISH 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Canister Steam System
GENERAL OPERATION
NOTE: Be sure that Boiler has been filled and that all desired accessories are connected
before following these steps.
1. For first time use, remove protective plastic cover from electrical plug. Plug power cord into a
electrical outlet.
2. Switch Lighted On/Off Switch to “On” position.
3. Once 2 Bar (29 PSI) is reached, the unit is ready to begin steaming. At approximately 4 Bar
(58 PSI), the unit will have maximum pressure.
NOTE: As steam is released, pressure will drop. This is a normal condition. When steam
flow is stopped, pressure will begin to increase. Normal pressure with continuous steam
flow is approximately 2 Bar (29 PSI).
4. Direct Nozzle (and any connected accessory) towards surface you desire to steam, and press
Steam Trigger. To sanitize surfaces, point Nozzle, press Trigger and hold approximately 1/2 inch
from surface for at least 5 seconds. This will insure that you have killed germs and bacteria.
CAUTION: Always be sure that Nozzle and any accessory are pointed in a safe direction
(away from yourself, other people, pets, and plants) before pressing Steam Trigger.
5. Keep Steam Trigger pressed for a continuous flow of steam. You may also hold the Steam Trig-
ger, then push the Steam Trigger Lock to lock it down. This will allow a continuous flow of steam
without need of holding the Steam Trigger down manually. Steam output can be adjusted by
simply turning the Steam Adjustment Knob.
6. Using a back-and-forth motion over the area you are steaming will further enhance the clean-
ing process. Wipe steamed areas with a clean cloth to remove loosened dirt and grime. Wip-
ing the area while it is still wet is recommended, but use caution when wiping surfaces such as metal
that may still be hot.
7. Once steaming tasks are complete, turn the unit “Off” and unplug. Follow steps under Proper
Storage procedure on Page 16 of this manual.
STEAM MOPPING
NOTE: Be sure that Boiler has been filled and that all steam mopping accessories are con-
nected before following these steps.
It is recommended to sweep or vacuum hard floors before mopping.
|
14 ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Canister Steam System
1. Follow Steps 1-3 of General Operation section above.
Refer to Page 9 for a listing of hard floor surfaces that are recommended for cleaning
with the Canister Steam System.
2. For best results, use a continuous back-and-forth motion over floor surface, pushing the Mop
Head away and pulling it back towards you. Work your way backwards over the floor, in order
to avoid walking over freshly mopped areas.
NOTE: To avoid warping or damage caused by heat and moisture, do not use on un-
sealed hardwood or unglazed ceramic surfaces. Steam may remove the sheen from
some floors that have been treated with wax.
3. The Microfiber Pad will absorb dirt and moisture during mopping. However, when you are
finished you may find some residual moisture has been left behind. In this case, it is recom-
mended to allow floor time to air-dry. A fan may be directed towards mopped area to facilitate
drying.
|
ENGLISH 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage & Care
PROPER STORAGE
Preparing your Canister Steam System for storage is quick and simple. When you have finished
your steaming tasks, follow the steps listed below.
1. Turn unit “Off” and unplug power cord.
2. Allow unit to completely cool (at least 30 minutes).
3. Press and hold Steam Trigger to release all remaining steam.
4. Remove all accessories from unit.
5. Carefully remove Boiler Cap.
6. Drain any remaining water from Boiler into a sink or tub – this will help to minimize mineral
build-up and prevent over-filling during your next use. Replace Boiler Cap loosely.
7. Store accessories. Utility Brushes can be conveniently stored in the Accessory Net. Remain-
ing accessories can be stored in the Storage Bag.
8. Store Canister Steam System in a cool, dry location.
MINERAL BUILD-UP
A common maintenance need for steam appliances is the removal of build-up caused by high
mineral content in many municipal water supplies. This mineral build-up may limit the effective-
ness and reduce the life of your Canister Steam System.
The best way to minimize mineral build-up is to use distilled or de-mineralized water when using
your Canister Steam System. If you are unable to use distilled water, it is recommended that the
following procedure be followed monthly to remove any mineral build-up:
1. Turn unit “Off” and unplug power cord.
2. Allow unit to completely cool (at least 30 minutes).
3. Press and hold Steam Trigger to release all remaining steam.
4. Remove all accessories from unit.
5. Carefully remove Boiler Cap.
6. Drain water from Boiler into a sink or tub.
7. Slowly pour 8 oz of vinegar into Boiler.
8. Allow to stand for 40 minutes.
9. Drain vinegar from Boiler.
10. Rinse Boiler with fresh water, drain and repeat until vinegar odor dissipates.
|
16 ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
PROBLEM
POSSIBLE CAUSE
SOLUTION
Unit fails to heat up.
Unit is not plugged in.
Plug power cord into electrical outlet.
Household circuit breaker / ground Reset circuit breaker / ground
fault interrupter has tripped or
blown a fuse.
fault interrupter, or replace fuse.
If you need assistance, contact a
licensed electrician.
Unit is damaged or otherwise in
need of repair.
Immediately cease usage and
unplug. Contact Consumer
Service for further assistance
(see Page 19 for details).
Boiler is empty.
Refer to Filling Boiler procedure
on Page 13.
Mineral build-up in unit.
Refer to Mineral Build-up section
on Page 16 for cleaning procedure.
Steam output is weak or
intermittent.
Water level in Boiler is running
low.
Refer to Filling Boiler procedure
on Page 13.
Mineral build-up in unit.
Refer to Mineral Build-up section
on Page 16 for cleaning procedure.
Excessive amount of water in
steam.
Water condensation in Steam
Hose.
Point nozzle towards sink, tub or
ground and shake while pressing
Steam Trigger. Continue until
excess water is released.
NOTE: Unit produces wet steam
– it is normal for steam to
Boiler has been
overfilled.
Filling the Boiler with more
than 48 oz. (1,420 ml.) of water
interferes with steam production,
resulting in water condensation
in steam.
contain some amount of water.
Always fill unit with correct amount
of water. (see Page 13 for details)
Accessories do not stay firmly
connected to Steam Nozzle.
Accessories not properly installed. Check to make sure that acces-
sories are properly connected, per
procedures on Pages 8-11.
Floor surfaces appear cloudy or
streaky after steaming.
Microfiber Pad is dirty.
Replace Microfiber Pad with a
clean one.
Hard water residue on floor.
Switch to distilled or
de-mineralized water.
Pressure Gauge will not reach 4
bar (58psi).
Variances in environmental tem-
perature and amount of water in
boiler could affect the amount of
pressure your unit will reach.
Unit will provide optimal steam
at 2 bar. Normal pressure with
continuous steam flow is approxi-
mately 2 Bar (29 PSI).
|
ENGLISH 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts & Accessories
Refer to the part numbers below when ordering parts and accessories
for your Canister Steam System.
Replacement Accessories
Jet Nozzle
Angled Nozzle
Triangle Brush
Large Brush
Nylon Utility Brush - 5 Pack
Brass Brush - 5 Pack
Round Brush - 5 Pack
Round Scrub Pad - 5 Pack
Fill Cup
A1230-001
A1375-001
A1230-002
A1230-003
A1230-005-5
A1230-006-5
A1350-001-5
A1230-007-5
A275-015
Scraper
Storage Bag
2 Extension Wands
Mop Head
Mop Head Brush Attachment
Microfiber Mop Pads - 2 Pack
A1230-009
A1375-010
A1375-002
A1375-003-A
A1375-004
A1375-100
Replacement Parts
Available via Consumer Service at 1-800-711-6617
Boiler Cap
T1230-001
|
18 ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Support
CONSUMER SERVICES
For problems with your Canister Steam System, please refer to the Troubleshooting guide located on Page
17 of this manual. Additional inquiries should be directed to our consumer support services through our
If you do not have internet access, you may also contact our Consumer Service Department by telephone,
at 1-800-711-6617.
NOTE: In order for our Consumer Service representatives to help you as quickly and efficiently as
possible, please have the following information ready before calling:
• Purchase information (where and when you purchased this product)
• Copy of purchase receipt / proof of purchase
• Product serial number (located on electrical specification label on back of unit)
• Date code (4-digit number located on electrical specification label)
PRODUCT SPECIFICATIONS
MC1375
120V
MODEL
VOLTAGE
1500W
POWER
48 oz. (1,420 ml)
WATER CAPACITY
HEATING TIME
CONTINUOUS STEAM TIME
UNIT WEIGHT
10-12 min. (approximate)
45 min high, 90 min low (approximate)
11 lbs. (5.0 kg.)
15.55" x 12.13" x 10.50" (39.5 cm x 30.8 cm x 26.7 cm)
UNIT DIMENSIONS
Warranty Information
1-YEAR LIMITED WARRANTY
What is covered
McCulloch® is a licensed brand of Steamfast, a division of Vornado Air, LLC (“Steamfast”). Subject to the terms and condi-
tions of this 1-Year Limited Warranty (“Warranty”) as set forth below, Steamfast warrants to the original consumer or pur-
chaser (“Buyer”) that this McCulloch®-branded steam product, excluding all accessories and attachments, (the “Product”) is
to be free from defects in material and workmanship for a period of one (1) year from the date of purchase when used and
maintained in accordance with the Owner’s Guide (the “Warranty Period”).
In the event Buyer notifies Steamfast of a defect in the Product within the Warranty Period, Steamfast will replace the
Product and/or defective component parts, as applicable and necessary. Any such replacement will be made at no charge
to Buyer for parts or labor, provided that Buyer shall be responsible for all shipping and transportation costs associated with
returning the Product to Steamfast for inspection and covered replacement.
What is not covered
This Warranty shall not be applicable to damage or loss caused in whole or in part by:
• Repairs, modifications or alterations to the Product by anyone other than Steamfast.
• Use or operation of the Product outside the permitted or intended uses described by Steamfast in the Owner’s Guide, or
other careless operation, handling, misuse, or abuse of the Product.
• Lack of proper maintenance or timely cleaning of the Product as specified in the Owner’s Guide.
• Use of the Product other than for normal household purposes.
• Normal wear and tear.
|
ENGLISH 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Information
• Used consumable parts, accessories and attachments, including, but not limited to, brushes, hangers, scrub pads and
mop pads.
• Use of parts and accessories other than those produced or recommended by Steamfast.
• Cosmetic damage, such as scratches, nicks and dents.
• Damage caused by accident, water, flood, fire or other acts of nature or external causes.
Warranty limitations and exclusions
• NO OTHER EXPRESS WARRANTY IS GIVEN BY STEAMFAST TO BUYER AND NO REPRESENTATIVE HAS THE
AUTHORITY TO MAKE REPRESENTATIONS OTHER THAN THOSE PROVIDED HEREIN.
• THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND ALL
IMPLIED WARRANTIES, SPECIFICALLY THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY LIMITED TO THE DURATION OF THE WARRANTY PERIOD,
UNLESS A SHORTER PERIOD IS PERMITTED BY LAW.
• STEAMFAST’S REPLACEMENT OF THE PRODUCT IS THE EXCLUSIVE REMEDY. UNDER NO CIRCUMSTANCES
SHALL STEAMFAST BE LIABLE TO BUYER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL, CON-
SEQUENTIAL, OR OTHER DAMAGES, EVEN IF STEAMFAST HAS BEEN ADVISED OF OR COULD REASONABLY
FORESEE THE POSSIBILITY OF SUCH DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR
DAMAGE, WHETHER RISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT OR UNDER ANY OTHER
THEORY OF LAW.
• THIS WARRANTY GIVES BUYER SPECIFIC LEGAL RIGHTS. BUYER MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE-TO-STATE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, AND SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO BUYER.
How do you register the Warranty
Buyer must complete an application to register this Warranty within sixty (60) days following date of purchase. Buyer
application to Steamfast. Failure to register this Warranty within sixty (60) days following date of purchase will render this
Warranty null and void.
Warranty service
For warranty service, call 1-800-711-6617 or email [email protected] to obtain a Return Authoriza-
tion (“RA”) form. Include the Product model number and serial number, as well as Buyer’s name, address, city, state, zip
code and phone number when contacting Steamfast for warranty service. Buyer may be required to provide the original
sales receipt for purposes of verifying date of purchase. After receiving the RA form, the Product must be shipped, postage
prepaid by Buyer, to:
Steamfast
Attn: Warranty & Repair
415 E. 13th Street
Andover, KS 67002
To assure proper handling, packages must be clearly marked with the RA number. Packages not clearly marked with the RA
number may be refused at the receiving dock.
Important: After receiving return authorization, carefully pack the Product to avoid damage in shipping. Damage in shipping
is not covered by the Warranty and shall be the sole responsibility of Buyer. Damage or loss not covered by this Warranty or
occurring outside the Warranty Period will require a fee to cover the cost of handling and shipping. All such fees and costs
shall be the sole responsibility of Buyer.
Please allow at least 1-2 weeks for return of the Product after it is received by Steamfast. For ease of recordkeeping, it is
recommended that Buyer staple or attached the original sales receipt to this Owner’s Guide and record the Product serial
number (located on the Product specifications decal) here:
________________________________________________
© 2013 Vornado Air, LLC • Andover, KS 67002
Specifications subject to change without notice. Steamfast® is a trademark owned by Vornado Air, LLC.
Manufactured in China.
|
20 ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
review this product online
evalúe este producto en línea
évaluer ce produit en ligne
Manufactured by Vornado Air LLC under license from Husqvarna AB (publ).
For more information on other McCulloch products,
For questions, or comments or warranty information,
T1375-005, R-V02
Download from Www.Somanuals.com. All Manuals Search And Download.
|