MM-6854 / MM-6864
GSM Dual-Band Data Modem
MM-6854
MM-6864
Application Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
WARNINGS
Internal components containing beryllium oxide are used in the equipment. Dust from this material is a
health hazard if inhaled or allowed to come into contact with the skin. Great care must be taken when
handling these components. They must not be broken or subjected to excessive heat.
Never operate the modem without the correct Maxon antenna, or a suitable artificial load, connected.
Never modify a modem, or accessory, except as instructed by Maxon in a formal communication as this may
invalidate any warranty, guarantee or type approval.
Do not operate this equipment in environments containing explosive materials or vapour. This includes
Petrol service stations.
This equipment should only be operated while stationary or with a hands-free accessory, provided that doing
so does not interfere with driving safety.
This equipment should not be operated on an aircraft as it is forbidden by law. It should not be operated in
the vicinity of medical equipment.
Issue 1.0
03/00
ME 820047
Page i
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
ME 820047
Page ii
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
TABLE OF CONTENTS
1 INTRODUCTION
1
1.1
1.2
1.3
1.4
1.5
1.6
Overview
1
1
1
1
1
2
How this document is organised
What are the MM6854/64
Recommended Procedures
Contact Information
Summary
2 SPECIFICATIONS
3
2.1
2.2
Basic Specifications
Summary
3
4
3 SYSTEM APPLICATIONS
5
6
3.1.1
GSM / GPS Application
4 OPERATION
7
4.1
4.2
Introduction
Network Connection
7
7
7
8
8
8
9
9
4.2.1
Inserting the SIM card
Turning on the modem
V.24 Interface
Set up the appropriate software
Confirming Operation
Summary
4.3
4.4
4.5
4.6
4.7
5 AT COMMANDS
11
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
5.1.6
5.1.7
5.1.8
5.1.9
+++<CR> - Escape command
A – Re-execute last command
ATA – Manually answer an incoming call
ATD – Dial a telephone number
ATDL
ATE – Command Echo
ATH – Hang up
ATIn - Identification
12
12
13
13
13
14
14
14
15
15
15
15
16
16
16
16
16
17
17
17
17
17
18
18
18
18
19
19
19
20
ATO0 – Return to transparent mode (switch from command mode to data mode).
5.1.10 ATQ - Result code suppression
5.1.11 ATS0=n – Auto-answer mode
5.1.12 ATS1? – Number of rings
5.1.13 ATS2- Escape character
5.1.14 ATS3 – Command line termination character
5.1.15 ATS4 – Line Feed character
5.1.16 ATS5 – Backspace character
5.1.17 ATS6 – Pause before blind dialling
5.1.18 ATS7 – Wait time for carrier
5.1.19 ATS8 – Wait time before dialling
5.1.20 ATS10 – Wait time before disconnection
5.1.21 ATS12 – Escape code guard time
5.1.22 ATV – Results code format
5.1.23 ATX – Defines CONNECT results code format
5.1.24 ATZ – Load user profile
5.1.25 AT&C – Data carrier detect options
5.1.26 AT&D – Data Terminal Ready options
5.1.27 AT&F – Restore default configuration
5.1.28 AT&V – Display current configuration
5.1.29 AT&W – Save current configuration
5.1.30 AT+CBSTs,m,p – Select bearer service type
Issue 1.0
03/00
ME 820047
Page iii
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.31 AT+CEER – Displays why last call was disconnected
5.1.32 AT+CMGD – Delete messages
5.1.33 AT+CMGF – Message format
5.1.34 AT+CMGL – List messages
5.1.35 AT+CMGR – Read messages
20
20
21
21
22
22
23
23
24
25
25
25
26
26
26
27
27
28
28
28
29
29
29
29
30
30
30
30
31
31
32
32
32
33
33
34
35
5.1.36 AT+CMGS – Send messages
5.1.37 AT+CMGW – Write messages to memory
5.1.38 AT+CMSS – Send messages from storage
5.1.39 AT+CNMI – New Message
5.1.40 AT+CPIN – Enter PIN and query blocks
5.1.41 AT+CR – Cellar result code for outgoing calls
5.1.42 AT+CRC – Cellar result code
5.1.43 AT+CRLP – Radio Link Protocol parameters
5.1.44 AT+CSCA – Service centre address
5.1.45 AT+CSDH – Show test mode parameters
5.1.46 AT+CSMP – Set text mode parameters
5.1.47 AT+DR – Data compression report
5.1.48 AT+DS – Data compression mode
5.1.49 AT+FCLASS – Select, read or test service class
5.1.50 AT+FMI – Report manufacturer ID
5.1.51 AT+FMM – Report module ID
5.1.52 AT+FMR – Report revision
5.1.53 AT+FRH – Receive HDLC data with carrier
5.1.54 AT + FRM – Receive data with carrier
5.1.55 AT+FTH – Transmit HDLC data with carrier
5.1.56 AT+FTM – Transmit data with carrier
5.1.57 AT+GMI – Request manufacturer ID
5.1.58 AT+GMM – Request model ID
5.1.59 AT+GMR – Request revision ID
5.1.60 AT+ICF – Character framing
5.1.61 AT+IFC – Local flow control
5.1.62 AT+ILRR – Display local report rate
5.1.63 AT+IPR – Set terminal equipment data rate
5.1.64 CME ERROR<n>
5.1.65 CMS ERROR<n>
5.1.66 S Register Summary
5.2
Summary
6 DEBUGGING & INDICATOR LIGHTS
37
37
6.1
Summary
7 INSTALLATION
39
7.1
7.2
7.3
7.4
7.5
7.6
7.7
Introduction
Antennas
Power Sources
Fusing
Cabling
Fixing
39
39
39
39
40
40
41
41
41
41
Connections
7.7.1
7.7.2
7.8 Summary
9 pin D-type (RS-232 Interface)
25 pin D-type
8 APPENDICES
43
8.1
Setting up Windows Modem interface
43
43
43
44
44
45
8.1.1
Open up the Control Panel
8.1.2
8.1.3
8.1.4
8.1.5
Double click on the modem icon
Highlight the don’t detect my modem box
Select the standard 19200 modem
Select the appropriate COM port
ME 820047
Page iv
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.1.6
8.1.7
8.1.8
8.1.9
Set the location information
Finish Installation
Select Properties
45
46
46
47
47
48
48
49
49
50
50
51
51
52
52
53
53
53
55
Select Connection
8.1.10 Set Data Bits, Parity and Stop bits
8.1.11 Select Flow Control and Software (XON/XOFF)
8.1.12 RS-232
8.2
Setting up Hyper Terminal
8.2.1
Select Hyper Terminal from Programs Menu
Select Hyper Terminal
Select Properties
Set Port
Port Settings
Properties
8.2.2
8.2.3
8.2.4
8.2.5
8.2.6
8.2.7
ASCII settings
8.3
8.3.1
8.3.2
8.4
Setting up Win Fax Pro
Communication Setup
Win Fax Pro Setup
Accessories
9 GLOSSARY
57
LIST OF FIGURES
Figure 3-1 - Applications.................................................................................................................................... 5
Figure 3-2 - GSM / GPS Application.................................................................................................................. 6
Figure 4-1 - Location of SIM card ...................................................................................................................... 7
Figure 4-2 - Securing of SIM card...................................................................................................................... 8
Figure 7-1 - Fixing centres for MM-6854 modem ............................................................................................ 40
LIST OF TABLES
Table 7-1 - 9 pin D-type socket connections ................................................................................................... 41
Table 7-2 - 25 pin D-type plug connections..................................................................................................... 41
Issue 1.0
03/00
ME 820047
Page v
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
ME 820047
Page vi
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
1 INTRODUCTION
1.1 Overview
This document provides Application information for the MM-6854/64 GSM Dual-Band Data Modem
and refers to software version 1.07 onwards.
This first section provides a brief overview of the products. Further sections go into more detail on the
various functions that are available and how they can be applied.
1.2 How this document is organised
Section 1 – Brief overview of the modems.
Section 2 – Basic Specifications
Section 3 – Typical Applications
Section 4 – Operation
Section 5 – AT Commands
Section 6 – Debugging and Indicator Lights
Section 7 – Installation – Covers the main points of installation.
Section 8 – Appendices - Provides information on the configuration of PCs.
Section 9 – Glossary
1.3 What are the MM6854/64
The MM-6854/64 are GSM Dual-Band Data Modems, they differ by the following:
MM-6854
Boxed modem, featuring internal back-up battery, requiring only the connection of
power and RS-232 serial data.
MM-6864
Basic PCB OEM GSM modem. For integration into a customer’s equipment.
1.4 Recommended Procedures
1. Radio Link Protocol should be used.
2. Observe flow control.
3. Data is not acknowledged, therefore ensure that the application does this.
1.5 Contact Information
Should you have any queries regarding this manual, or the information within it, please contact:
The Technical Support Group
Maxon Europe Limited.
Maxon House, Maxted Close
Hemel Hempstead
Hertfordshire HP2 7EG
United Kingdom
Telephone: +44 (0) 1442 267777
Fax: +44 (0) 1442 215515
Technical Support Direct Telephone Line: +44 (0) 1442 298988
Technical Support Direct Fax Line:
+44 (0) 1442 242363
Issue 1.0
03/00
ME 820047
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
1.6 Summary
This section has provided a basic introduction to the products.
ME 820047
Page 2
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
2 SPECIFICATIONS
2.1 Basic Specifications
Performance
91/263/EEC
Specifications
ETS 300 342-1
ETSI GSM 0707/05 AT commands plus Extended
SMS GSM rec. 7.05 including PDU mode
GSM 04.21 transparent data
GSM 04.22 non-transparent data
890 to 960MHz
1710 to 1880MHz
Class 4 (2W) for 900MHz
Class 2 (1W) for 1800MHz
Frequency Range
RF Output Power
Receiver Sensitivity
Modulation Type
-102dBm at 900MHz, -100dBm at 1800MHz
(<2% bit error rate)
Modified GMSK
Intermediate Frequency
282MHz
Transmit Attack Time
RS-232 Interface
<25mS
V24 9 pin D-type
Baud rate 300 – 57600 baud, no autobauding. Set to 19200
as default.
Parity: None, Space, Odd, Even or Mark
Character Format: 7 or 8
Stop bits: 1 or 2
Level: To CCITT Recommendation V.28
Transparent
Data Communication
Non-error corrected link according to GSM 04.21
User rates:
2400 bps
4800 bps
9600 bps
14400 bps
V.22 bis / V.26 ter / V.110
V.32 / V.110
V.32 / V.110
V.32 / V.110 GPRS1
Non-Transparent
Error connected link according to GSM 04.22 (V.42)
User rates:
9600 bps
V.32 / V.110
14400 bps
V.32 / V.110 GPRS1
Note: When using V.110, the correspondent has to be an
ISDN adapter. Data compression according to V.42 bis.
Transparent Fax
Group 3, Class 1 support only.
User rates;
2400 bps
4800 bps
7200 bps
9600 bps
SMS
GSM rec. 7.05, including PDU mode
Small size SIM, 3 or 5V
SIM card Interface
Issue 1.0
03/00
ME 820047
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
General Specifications
Temperature Range
Operating
Charging
(Performance without degradation unless stated)
-20 to +60 C
°
0 to +40 C
°
Power Consumption
Standby
25mW
Charging / On-air
4W max.
Current Consumption
Supply Voltage
12V
24V
333mA – fit 800mA A/S fuse
166mA – fit 500mA A/S fuse
+9V minimum to +28V DC maximum
Dimensions
Weigh
172mm long x 82mm wide x 30mm high
260 grams
Note
: Maxon Europe reserves the right to alter these specifications without prior notification as part of
our continuous improvement policy.
2.2 Summary
This section has outlined the basic specifications of the MM6854/64.
ME 820047
Page 4
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
3 SYSTEM APPLICATIONS
Fleet Management
Construction
Transportation
Emergency Services
Delivery Vans
Anti-Theft
Utilities
Refrigerated Trucks
Taxis
Courier Companies
Vending Machines
Surveillance
Figure 3-1 - Applications
Issue 1.0
03/00
ME 820047
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
3.1.1 GSM / GPS Application
One example of an application is sending data and GPS information via the GSM Network.
GPS Antenna
GSM Antenna
Terminal
GSM Modem
Control
Unit
Mobile Equipment
Computer
GSM Antenna
GSM Modem
Host Application
Figure 3-2 - GSM / GPS Application
ME 820047
Page 6
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
4 OPERATION
4.1 Introduction
This section covers the simple operation of the modems. It provides the relevant information for the
user to get the modem up and running.
A +9V to +28VDC power supply will be required, together with a Windows 95 PC, installed with Hyper
Terminal, or similar package, a CA8360 power cable, a CA8401 antenna and a CA8361 PC serial
cable.
4.2 Network Connection
It is necessary to obtain a SIM from your chosen Network Provider. This SIM must be suitable for
Data service.
All information needed to connect you to the network and to initiate billing for your calls is stored in the
gold-plated area of the SIM card, along with the names, numbers and messages you have entered
into the phone book, or received.
To prevent either, the loss of information or corruption of information, avoid touching the gold area and
do not place the SIM near electrical or magnetic fields.
A damaged SIM will not allow you to access the GSM network.
4.2.1 Inserting the SIM card
The SIM card will probably be supplied in a cardholder and will need to be carefully pressed free,
before fitting.
The modem must not be powered. If the 25 way D-type connector is removed, this ensures that this is
the case. The modem should be turned upside down and the two small countersunk screws removed
to expose the SIM card area.
Figure 4-1 - Location of SIM card
Issue 1.0
03/00
ME 820047
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
Care should be taken to ensure that the card is correctly fitted and is held in place. This is
accomplished by fitting the card (with the gold area facing downwards) underneath the two lugs and
sliding the metal holder over the top of the card to secure it.
then
SIM card
inserted here
Metal
Holder
The lid can now be attached and held in place with the two screws.
Figure 4-2 - Securing of SIM card
4.3 Turning on the modem
To turn on the modem, connect power between pin 16 (+9V to +28VDC) and pin 17 (GND) of the D25
connector. Alternatively, fit accessory cable CA8360 and connect power between the red and black
leads. Connect a suitable antenna; the Maxon CA8401 is ideal.
Note
: It is important that the antenna ground is not connected to the modem ground. This will not
happen where through glass antennas are used. Antennas, which are through chassis mounting and
connect to the vehicle chassis should not be used. Failure to observe this may result in damage to the
unit and will invalidate the warranty.
Pin 15 of the D25 connector has to be pulled LOW in order to turn on the modem. Alternatively, fit
accessory cable CA8360 and connect the green lead to GND.
Provided that the SIM card is unlocked, the modem will make an automatic search for your home
network or another suitable network operator in your location. The modem will initially flash RED as it
establishes a network connection (within seconds) and then flash GREEN.
Note
: To prevent unauthorised use, the SIM can be protected by a PIN code (See Section 5.1.40).
Each time the modem is switched on the PIN code must be entered. If you enter the wrong code,
three times in succession, your SIM will be barred from the network and the modem will require a PUK
code.
4.4 V.24 Interface
The modem is set to communicate with a baud rate, which is set as default to 19200 baud. The
modem does not support autobaud and therefore it is important that any equipment, which
communicates with the modem, is set to 19200 baud.
4.5 Set up the appropriate software
Information is provided in Section 8.2 for setting up Hyper Terminal and TAPI devices for use with the
modems.
ME 820047
Page 8
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
4.6 Confirming Operation
On Hyper Terminal, type ATD <Telephone number you want to ring> and press Carriage Return.
The telephone will ring. The answer tone will be similar to the one, which you would receive, with a
fax machine.
4.7 Summary
This section has covered the basic operation of the modem.
Issue 1.0
03/00
ME 820047
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
ME 820047
Page 10
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5 AT COMMANDS
Command
+++
A/
ATA
ATD
ATDL
ATE
ATH
ATIn
ATO0
ATQ
ATS0=n
ATS1?
ATS2
ATS3
ATS4
ATS5
ATS6
ATS7
ATS8
ATS10
ATS12
ATV
ATX
ATZ
AT&C
AT&D
Function
Paragraph
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
5.1.6
5.1.7
5.1.8
Switch from data mode to command mode
Re-execute the last command
Manual answer an incoming call
Dial a telephone number
Redial the last telephone number
Command echo
Hang up
Identification
Switch from command mode to data mode
Result code suppression
Auto answer mode
Number of rings
Escape character
Command line termination character
Line Feed character
Backspace character
Set pause before blind dialling
Wait time for carrier
Wait time before dialling
Wait time before disconnection
Escape code guard time
Result code format
Page 12
Page 12
Page 13
Page 13
Page 13
Page 14
Page 14
Page 14
Page 15
Page 15
Page 15
Page 15
Page 16
Page 16
Page 16
Page 16
Page 16
Page 17
Page 17
Page 17
Page 17
Page 17
Page 18
Page 18
Page 18
Page 18
Page 19
Page 19
Page 19
Page 20
Page 20
Page 20
Page 21
Page 21
Page 22
Page 22
Page 23
Page 23
Page 24
Page 25
Page 25
Page 25
Page 26
Page 26
Page 26
Page 27
5.1.9
5.1.10
5.1.11
5.1.12
5.1.13
5.1.14
5.1.15
5.1.16
5.1.17
5.1.18
5.1.19
5.1.20
5.1.21
5.1.22
5.1.23
5.1.24
5.1.25
5.1.26
5.1.27
5.1.28
5.1.29
5.1.30
5.1.31
5.1.32
5.1.33
5.1.34
5.1.35
5.1.36
5.1.37
5.1.38
5.1.39
5.1.40
5.1.41
5.1.42
5.1.43
5.1.44
5.1.45
5.1.46
Defines CONNECT result code format
Load user profile
Data Carrier Detect Options
Data Terminal Ready Options
Restore default configuration
Display current configuration
Save current configuration
Select bearer service type
Displays why last call was disconnected
Delete messages
Message format
List messages
Read message
Send messages
Write messages to memory
Send messages from storage
New Message
Enter PIN and query blocks
Cellar result code for outgoing calls
Cellar result code
Radio Link Protocol parameters
Service centre address
Show test mode parameters
Set text mode parameters
AT&F
AT&V
AT&W
AT+CBSTs,m,p
AT+CEER
AT+CMGD
AT+CMGF
AT+CMGL
AT+CMGR
AT+CMGS
AT+CMGW
AT+CMSS
AT+CNMI
AT+CPIN
AT+CR
AT+CRC
AT+CRLP
AT+CSCA
AT+CSDH
AT+CSMP
Issue 1.0
03/00
ME 820047
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
Command
AT+DR
AT+DS
AT+FCLASS
AT+FMI
AT+FMM
AT+FMR
AT+FRH
AT+FRM
AT+FTH
AT+FTM
AT+GMI
AT+GMM
AT+GMR
AT+ICF
Function
Paragraph
5.1.47
5.1.48
5.1.49
5.1.50
5.1.51
5.1.52
5.1.53
5.1.54
5.1.55
5.1.56
5.1.57
5.1.58
5.1.59
5.1.60
5.1.61
5.1.62
5.1.63
Data compression report
Data compression mode
Select, read or test service class
Report Manufacturer ID
Report module ID
Page 27
Page 28
Page 28
Page 28
Page 29
Page 29
Page 29
Page 29
Page 30
Page 30
Page 30
Page 30
Page 31
Page 31
Page 32
Page 32
Page 32
Report revision
Receive HDLC data with carrier
Receive data with carrier
Transmit HDLC data with carrier
Transmit data with carrier
Request manufacture ID
Request model ID
Request revision ID
Character framing
Local flow control
Display local report rate
Set terminal equipment data rate
AT+IFC
AT+ILRR
AT+IPR
Error Result Codes
Command
+CME ERROR
+CMS ERROR
S register summary
Paragraph
5.1.64
5.1.65
Page 33
Page 33
Page 34
5.1.66
5.1.1 +++<CR> - Escape command
By sending the escape sequence +++<CR>, the modem will return to AT command mode. Then you
can send the ATH command for automatic termination of the connection:
Enter
Response
+++<CR>
OK
Notes: None
Result codes: None
5.1.2 A – Re-execute last command
The A/command lets you re-execute the last command entry. This command is not preceded by AT
and does not have to end with <CR>:
Enter
Response
ATD12345678<CR>
A/
BUSY
ATD12345678 (Re-executes the last AT command
Notes: None
Result codes: None
ME 820047
Page 12
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.3 ATA – Manually answer an incoming call
The modem does not automatically answer an incoming call (Default setting). The ATA command
causes the modem to go off-hook when the modem rings:
Enter
Response
ATA
The modem will answer the incoming call
Notes: None
Result codes: None
5.1.4 ATD – Dial a telephone number
This command will dial the number entered after the ATD command:
Enter
Response
ATD12345678<CR>
The modem dials the telephone number 12345678
Connect 14400 (Selected speed)
Notes:
As soon as the modem detects the carrier from the GSM base
station, it returns the CONNECT result code. Data transmission
can now begin.
The following characters are valid in a dial string: The digits
from “0” to “9”, and “+” for making International calls. The +
must be at the beginning of the number.
Result codes:
ERROR
NO CARRIER
CONNECT<selected speed>
Mobile equipment result code
5.1.5 ATDL
This command will dial the last number, which the modem dialled:
Enter
Response
ATDL<CR>
12345678 where 12345678 was the last number dialled.
Connect 14400 (Selected speed)
Notes: None
Result codes:
ERROR
NO CARRIER
CONNECT<selected speed>
Mobile equipment result code
Issue 1.0
03/00
ME 820047
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.6 ATE – Command Echo
This command is used to enable and disable echo.
Enter
Response
ATE0
ATE1
Disable echo.
Enable echo.
Notes: None
Result codes:
OK
ERROR
5.1.7 ATH – Hang up
This command is used for asynchronous transmission only. If the user returns from data mode to
command mode after sending an escape sequence (+++) or after disabling the DTR signal with
AT&D1 option, the modem can be forced to disconnect by sending the ATH command.
Enter
Response
ATH
Notes: None
Result codes:
OK
ERROR
5.1.8 ATIn - Identification
This command provides information about the product identification.
Enter
Response
ATIn
Mode
ATI0
Product Code
ATI1
ATI2
Pre-computed checksum
Returns OK
ATI3
Returns OK
ATI4
OEM String
ATI5 to I11
ATI12
ATI13
ATI14
ATI15
ATI17
Returns OK
ROM Checksum
RC Version number
Shows firmware version
Shows selected country
GSM option
Notes: None
Result codes:
OK
ERROR
ME 820047
Page 14
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.9 ATO0 – Return to transparent mode (switch from command mode to data
mode).
If you wish to interrupt the data flow only briefly, you can use the ATO0 command to return your
modem to the transparent mode, i.e. the data flows once again.
Enter
ATO0
Response
Notes: None
Result codes:
OK
ERROR
5.1.10 ATQ - Result code suppression
This command is used to enable and disable the result code.
Enter
Response
ATQ0
ATQ1
Enable result code
Disable result code
Notes: None
Result codes:
OK
ERROR
5.1.11 ATS0=n – Auto-answer mode
Enter
Response
ATS0=0
ATS0=1
….etc.
No auto-answer, incoming calls are ignored (Default value).
The modem will answer incoming calls after the first ring.
ATS0=5
The modem will answer incoming calls after the fifth ring.
The modem will answer the incoming call.
ATA
Notes:
The ATA command can still be used regardless of the
value of the ATS0=n string.
The S0 register can be read out by the ATS0? command, the
modem will then display the current value.
Result codes:
OK
ERROR
5.1.12 ATS1? – Number of rings
Displays the number of rings, which the modem has detected. This register is cleared when no rings
occur for 8 seconds, or when the value becomes equal to S0.
Issue 1.0
03/00
ME 820047
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.13 ATS2- Escape character
Typing ATS2? will display the decimal value of the ASCII character used as the escape character.
The default value (43) corresponds to an ASCII <+>. The value 127 disables the escape process.
Enter
Response
ATS2=127
ATS2=43
Disables the escape process.
Sets + as the escape character (default).
Notes: None
Result codes: None
5.1.14 ATS3 – Command line termination character
Typing ATS3? will display the decimal value of the ASCII character used as the carriage return
character. The default value (13) corresponds to an ASCII <CR>. Affects asynchronous operation
only.
Enter
Response
ATS3=13
Sets CR as the command line termination character (default).
Notes:
Setting any other value than 13 may cause problems
when entering commands.
Result codes: None
5.1.15 ATS4 – Line Feed character
Typing ATS4? will display the decimal value of the ASCII character used as the line feed character.
The default value (10) corresponds to an ASCII <LF>. Affects asynchronous operation only.
Enter
Response
ATS4=10
Sets LF as the line feed character (default).
Notes:
None.
Result codes: None
5.1.16 ATS5 – Backspace character
Typing ATS5? will display the decimal value of the ?ASCII character used as the backspace
character. The default value (8) corresponds to an ASCII <backspace>. Affects asynchronous
operation only.
Enter
Response
ATS5=8
Sets backspace as the backspace character (default).
Notes:
None.
Result codes: None
5.1.17 ATS6 – Pause before blind dialling
The value of this register is ignored.
ME 820047
Page 16
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.18 ATS7 – Wait time for carrier
After dialling, this register sets the time that the modem must wait before hanging up if it fails to detect
the remote carrier. Time is in seconds.
Enter
Response
ATS7=60
Sets the wait for carrier time to 60 seconds (default).
Notes:
None.
Result codes: None
5.1.19 ATS8 – Wait time before dialling
Sets the number of seconds to wait when the comma dial modifier is encountered in the dial string.
Enter
Response
ATS8=2
Sets the wait time before dialling to 2 seconds (default).
Notes:
None.
Result codes: None
5.1.20 ATS10 – Wait time before disconnection
Set the number of tenths of seconds to wait before disconnecting after the modem has indicated the
absence of the received line signal.
Enter
Response
ATS10=15
Sets the wait time before disconnection to 15 seconds (default).
Notes:
None.
Result codes: None
5.1.21 ATS12 – Escape code guard time
Defines the maximum silence time, in fiftieths of a second, accepted between two characters in an
escape sequence.
Enter
Response
ATS12=10
Sets the escape code guard time to 0.2 seconds (default).
Notes:
None.
Result codes: None
5.1.22 ATV – Results code format
This command is used to select short or long result codes.
Enter
Response
ATV0
ATV1
Sets short result codes.
Sets long result codes.
Notes:
None.
Result codes:
OK
ERROR
Issue 1.0
03/00
ME 820047
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.23 ATX – Defines CONNECT results code format
This command is used to define the result code for CONNECT.
Enter
Response
ATX0
ATX1
Modem returns only the CONNECT code as soon as a
satisfactory connection has been set up.
Modem returns only the CONNECT<SPEED> code as soon as a
satisfactory connection has been set up.
Notes:
ATX2, 3 & 4 perform the same function as ATX1.
Result codes: None
5.1.24 ATZ – Load user profile
This command will load a user-defined profile.
Enter
Response
ATZ0
User profile 0 is loaded.
Notes:
None.
Result codes:
OK
ERROR
5.1.25 AT&C – Data carrier detect options
This command affects the DCD line connected to the serial port.
Enter
Response
AT&C0
AT&C1
Sets the GSM module DCD control line to ON regardless of the
data carrier status of the distant station.
DCD specifies the data carrier status of the distant station.
DCD on indicates that a connection exists.
Notes:
None.
Result codes:
OK
ERROR
5.1.26 AT&D – Data Terminal Ready options
This command affects the DTR line connected to the serial port.
Enter
Response
AT&D1
AT&D2
The modem changes to the command mode when the DTR line
switches from ON to OFF.
The modem sets up a connection to the distant station, switches
to command mode and deactivates auto-answer mode when the
DTR line switches from ON to OFF. Auto-answer can be re-
activated by resetting DTR to ON.
Notes:
None.
Result codes:
OK
ERROR
ME 820047
Page 18
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.27 AT&F – Restore default configuration
This will force the modem to load the default configuration.
Enter
Response
Notes:
None.
Result codes:
OK
ERROR
5.1.28 AT&V – Display current configuration
The modem will display the current configuration.
Enter
Response
Notes:
None.
Result codes:
OK
ERROR
5.1.29 AT&W – Save current configuration
This command will allow you to save the current configuration.
Enter
Response
Notes:
None.
Result codes:
OK
ERROR
Issue 1.0
03/00
ME 820047
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.30 AT+CBSTs,m,p – Select bearer service type
Selects the bearer service to be used when data calls are originated.
Speed
S
0
1
2
3
4
5
6
7
Not supported
300bps / V.21
1200bps / V.21
1200/75bps / V.21
2400bps / V.22 bis
2400bps / V.26 ter
4800bps / V.32
9600bps / V.32
65
66
68
70
71
M
300bps / V.110
300bps / V.110
2400bps / V.110
4800bps / V.110
9600bps / V.110
Mode
0
P
Asynchronous
Protocol
0
Transparent
1
Non-transparent
Response
Enter
AT+CBST?
The modem will reply with the selected speed, mode and
protocol.
AT+CBST=?
The modem will reply with the supported speeds, modes and
protocols.
Result codes
OK
ERROR
5.1.31 AT+CEER – Displays why last call was disconnected
This command lets you query the reason why the last call was disconnected.
Enter
Response
Notes:
None.
Result codes:
OK
ERROR
5.1.32 AT+CMGD – Delete messages
This command is used to delete a received stored SMS message.
Enter
Response
AT+CMGD=<index>
Delete SMS entry corresponding to <index> where <index> is
the location in memory.
Notes:
None.
Result codes:
OK
ERROR
Message service failure result codes.
ME 820047
Page 20
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.33 AT+CMGF – Message format
This command allows you to define the input and output format of the short message.
Enter
Response
AT+CMGF=0
AT+CMGF=1
AT+CMGF=?
Set to PDU mode, a complete SMS message including all
header information is passed as a binary string.
Set to text mode, all commands and responses are in ASCII
characters.
Displays all supported values.
Notes:
None.
Result codes:
OK
ERROR
Message service failure result codes.
5.1.34 AT+CMGL – List messages
This command is used to list the SMS messages stored in the modem.
Enter
Response
AT+CMGL=<STAT>
Where <STAT>
In text mode:
“REC UNREAD”
“REC READ”
“STO UNSENT”
“STO SEND”
Receive unread messages.
Stored read messages.
Stored unsent messages.
Stored sent messages.
All messages
“ALL”
In PDU mode:
0
1
2
3
4
Received unread messages
Stored read messages
Stored unsent messages
Stored sent messages
All messages
AT+CMGL::<index>,
<stat>,<da>,<CR>,<LF>,<dat
a>
Where <data>
<da>
<index>
TP user data GSM 03.40
Destination Address type value according to GSM 03.40.
Location in memory.
AT+CMGL=?
Displays the supported values.
Notes:
None.
Result codes:
OK
ERROR
Message service failure result codes.
Issue 1.0
03/00
ME 820047
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.35 AT+CMGR – Read messages
This command is used to read SMS messages.
Enter
Response
AT+CMGR=<index>,<data>
Where
<index>
<data>
Integer indicating the location of the SMS to be read.
TP user data GSM 03.40
Notes:
None.
Result codes:
OK
ERROR
Message service failure result codes.
5.1.36 AT+CMGS – Send messages
This command is used to send SMS messages.
Enter
Response
In text mode:
AT+CMGS=”Receiver
number”<CR><text to be
sent>CtrlZ
OK
In PDU mode:
AT+CMGS=<length><CR><p
du>CtrlZ/esc
Where
<length>
Number of characters in text mode, or length of binary string in
PDU mode.
<pdu>
Binary string coded according to GSM 03.38
AT+CMGS<mr>
Where <mr>
Message reference according to GSM 03.40.
Notes:
Esc quits without sending.
Result codes:
OK
ERROR
Message service failure result codes.
ME 820047
Page 22
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.37 AT+CMGW – Write messages to memory
This command is used to store a SMS message into the memory.
Enter
Response
In text mode:
AT+CMGW=<oa/da><CR><t
ext to be stored>CtrlZ/esc
In PDU mode:
AT+CMGW=<length><CR><
pdu is given>CtrlZ/esc
Where
<da>
TP – Destination Address. Address value field in string format
GSM 03.40.
<length>
Number of characters in text mode, or length of binary string in
PDU mode.
Notes:
Esc quits without sending.
Result codes:
OK
ERROR
Message service failure result codes.
5.1.38 AT+CMSS – Send messages from storage
This command is used to send a stored SMS message.
Enter
Response
AT+CMSS=<index>[,<da>,<t Sends message stored in location corresponding to <index>.
oda>]
OK
Where
<da>
TP – Destination Address. Address value field in string format
GSM 03.40.
<index>
<mr>
<toda>
Location in memory
Message reference according to GSM 03.40.
Integer format of <da>.
Notes:
Result codes:
OK
ERROR
Message service failure result codes.
Issue 1.0
03/00
ME 820047
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.39 AT+CNMI – New Message
This command allows you to determine how the modem shall notify the user when a SMS message is
received from the network operator.
Enter
Response
AT+CNMI=<mode>,<mt>,<b
m>,<ds><bfr>
Set message indication mode.
AT+CNMI?
Display current values
+CNMI<mode>,<mt>,<bm>,<ds>,<bfr>
AT+CNMI=?
Where <mode>
Display list of supported values.
+CNMI<mode>,<mt>,<bm>,<ds>,<bfr>
Buffer unsolicited result code modem. If buffer is full, the oldest
indications may be discarded and replaced with the new
received indication.
Discard indication and reject new received messages unsolicited
result codes when serial port is in use. Otherwise forward them
directly to the user.
Buffer unsolicited result codes in the modem when the serial link
is in use and deliver them when the serial link is unused.
Forward unsolicited result codes directly to the user. Serial link
specific in-band used to embed result codes as data when the
modem is in on-line mode.
<mt>
Disable SMS-deliver indication.
If SMS-deliver is stored in modem, indication of memory location
routed to the user using +CMTI<mem>,<index> indication that
new message has been received.
SMS deliveries are routed directly to the user.
Class 3 SMS deliveries are routed directly to the user.
<bm>
No CBM, Cell Broadcast Message, is routed to the user.
If CBM, Cell Broadcast Message, is stored in modem, indication
of memory location is routed to the user using the
+CBMI<mem>,<index>.
SMS status disabled.
SMS status report enabled.
<bfr>
The results codes buffered in the modem are sent to the user
when mode 1…3 is entered.
The result code is cleared when mode 1…3 is entered.
Notes:
Result codes:
OK
ERROR
Message service failure result codes.
+CMTI<mem>,<index> indication that new messages has been
received.
+CBMI indication of new cell broadcast
ME 820047
Page 24
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.40 AT+CPIN – Enter PIN and query blocks
This command is used to validate the PIN code, or to validate the PUK code.
Enter
Response
AT+CPIN?
Displays the current status of the PIN code.
AT+CPIN=<puk>,<new_pin> If PUK code is required. New_pin will be the new pin code for
the SIM card.
AT+CPIN=<pin>
Enter the PIN code for the SIM card.
Notes:
Result codes:
OK
ERROR
+CPIN READY
+CPIN SIM PIN “Pin code required”
+CPIN SIM PUK “PUK code required”
+CPIN SIM PIN2 “Pin 2 code required”
Mobile equipment result code
5.1.41 AT+CR – Cellar result code for outgoing calls
AT+CR=?
5.1.42 AT+CRC – Cellar result code
This command controls whether or not the extended format of incoming call indication is used. When
enabled the modem will then send an extended string instead of the usual RING.
AT+CRC can have the value 0 or 1. If set to 0 the cellar result code will be disabled, and 1 will enable
the result code.
Enter
Response
AT+CRC=?
Displays the mode selected:
+CRING:ASYNC
For asynchronous transparent
+CRING:REL ASYNC For asynchronous non-transparent
+CRING:SYNC
+CRING:REL SYNC
+CRING:VOICE
+CRING:FAX
Notes:
For synchronous transparent
For synchronous non-transparent
For normal speech
For fax calls
Result codes:
OK
ERROR
Issue 1.0
03/00
ME 820047
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.43 AT+CRLP – Radio Link Protocol parameters
This command lets you change parameters for the radio link protocol, used only for NON-transparent
data transmission.
Enter
Response
AT+CRLP=<up-window
size>,<down window
size>,<acknowledgement
timer>,<retransmissions
attempts>,<reset
allowed>,<re-sequencing
time>
AT+CRLP?
Displays the current settings.
AT+CRLP=?
Displays the supported settings.
Notes:
None
Result codes:
OK
ERROR
5.1.44 AT+CSCA – Service centre address
This command shall be used to indicate to which service centre the message has to be sent.
The modem has no default value for this address. If a SMS is sent without having indicated the
service address, an error will be generated.
Enter
Response
AT+CSCA=”<sca>”
Where <sca>
GSM 04.11 RP SC address address-values field string format.
Displays the current value.
AT+CSCA?
Notes:
None
Result codes:
OK
ERROR
Message service failure result codes
5.1.45 AT+CSDH – Show test mode parameters
This command is used to determine if a detailed header information is shown in text mode result
codes.
Enter
Response
AT+CSDH=0
AT+CSDH=1
AT+CSDH?
AT+CSDH=?
Disable header information.
Enable header information
Displays the current value.
Displays the supported values
Notes:
None
Result codes:
OK
ERROR
Message service failure result codes
ME 820047
Page 26
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.46 AT+CSMP – Set text mode parameters
This command is used to select additional values, when a SMS is sent to the network, or placed in
storage, when text format.
Enter
Response
AT+CSMP=<fo>,<vp>
Where <fo>
Where <vp>
+CSMP<fo>,<vp>
The first octet of SMS-SUBMIT of GSM03.40
Validity period of the message in integer format.
Notes:
None
Result codes:
OK
ERROR
Message service failure result codes
5.1.47 AT+DR – Data compression report
This command is used to determine whether or not the intermediate result code of the current data
compression is reported after a connection set-up.
Enter
Response
AT+DR=0
AT+DR=1
AT+DR?
Disable reporting
Enable reporting
Displays the current value
Displays the supported values.
AT+DR=?
Notes:
None
Result codes:
OK
ERROR
+DR<type>
Where <type>
NONE
Data compression is not used.
V42B
Rec. V42bis for both directions
B42BRD
B42BTD
Rec. V42bis for receive direction only
Rec. V42bis for transmit direction only
Issue 1.0
03/00
ME 820047
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.48 AT+DS – Data compression mode
This command is used to determine the possible data compression mode between the modem and
the compression negotiation with the remote modem after call set-up.
Enter
Response
AT+DS=<p0>,<n>,<p1>,<p2
>
Where <p0>
0
1
2
3
None
Transmit only
Receive only
Both directions, but allow negotiation
Where <n>
0
1
Allow negotiation of <p0> down
Don’t allow negotiation of <p0 down, disconnect if difference
Where <p1>
512 – 1024
Dictionary size
Where <p2>
6 - 64
Maximum string
AT+DS?
Displays the current value.
Displays the supported values.
AT+DS=?
Notes:
None
Result codes:
OK
ERROR
5.1.49 AT+FCLASS – Select, read or test service class
This command is used to toggle between fax and data commands.
Enter
Response
AT+FCLASS=0
AT+FCLASS=1
AT+FCLASS?
AT+FCLASS=?
Set to data mode
Set to fax mode
Displays the current value
Displays the supported values
Notes:
None
Result codes:
None
5.1.50 AT+FMI – Report manufacturer ID
This command provides the name of the module manufacturer.
Enter Response
Notes:
None
Result codes:
OK
ERROR
ME 820047
Page 28
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.51 AT+FMM – Report module ID
This command provides the name of the module.
Enter
Response
Notes:
None
Result codes:
OK
ERROR
5.1.52 AT+FMR – Report revision
This command provides the version of the module and the software creation date.
Enter
Response
Notes:
None
Result codes:
OK
ERROR
5.1.53 AT+FRH – Receive HDLC data with carrier
Receive data with HDLC Framing. +FRH=n causes the modem to transmit data using HDLC protocol
and the modulation defined below. An ERROR response code results if this command is issued while
the modem is on-hook.
Enter
Response
AT+FRH=<mod>
Where <mod>
3
V.21
300bps
AT+FRH=?
Displays supported values
Notes:
None
Result codes:
OK
ERROR
5.1.54 AT + FRM – Receive data with carrier
Enter
Response
AT+FRM=<mod>
Where <mod>
24
48
72
96
V.27 ter 2400bps
V.27 ter 4800bps
V.29
V.29
7200bps
9600bps
AT+FRM=?
Displays supported values
Notes:
None
Result codes:
OK
ERROR
Issue 1.0
03/00
ME 820047
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.55 AT+FTH – Transmit HDLC data with carrier
Transmit data with HDLC Framing. +FTH=n causes the modem to receive data using HDLC protocol
and the modulation defined below. An ERROR response code results if this command is issued while
the modem is on-hook.
Enter
Response
AT+FTH=<mod>
Where <mod>
3
V.21
300bps
AT+FTH=?
Displays supported values
Notes:
None
Result codes:
OK
ERROR
5.1.56 AT+FTM – Transmit data with carrier
Transmit data. +FTM=n causes the modem to transmit data using the modulation defined below. An
ERROR response code results if this command is issued while the modem is on-hook.
Enter
Response
AT+FTM=<mod>
Where <mod>
24
48
72
96
V.27 ter 2400bps
V.27 ter 4800bps
V.29
V.29
7200bps
9600bps
AT+FTM=?
Displays supported values
Notes:
None
Result codes:
OK
ERROR
5.1.57 AT+GMI – Request manufacturer ID
This command provides the name of the manufacturer, i.e. Maxon.
Enter
Response
Notes:
None
Result codes:
OK
ERROR
5.1.58 AT+GMM – Request model ID
This command provides the model name, i.e. MM-6854.
ME 820047
Page 30
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.59 AT+GMR – Request revision ID
Enter
Response
Notes:
None
Result codes:
OK
ERROR
5.1.60 AT+ICF – Character framing
This command is used to determine the start-stop (asynchronous) character framing that the modem
shall use.
Enter
Response
AT+ICF=<format>,<parity>
Where <format>
1
2
3
4
5
6
8 data, 2 stop
8 data, 1 parity, 2 stop
8 data, 1 stop
7 data, 2 stop
7 data, 1 parity, 1 stop
7 data, 1 stop
Where <parity>
0
1
2
3
Odd
Even
Mark
Space
AT+ICF?
Displays the selected values
AT+ICF=?
Displays the supported values
Notes:
None
Result codes:
OK
ERROR
Issue 1.0
03/00
ME 820047
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.61 AT+IFC – Local flow control
This command is used to control the operation of local flow control between the modem and
equipment interfacing the modem.
Enter
Response
AT+IFC=<DCE_DTE>,<DTE
_DCE>
Where <DCE_DTE>
1
2
3
4
None
Xon/Xoff local
RTS
Xon/Xoff global
Where <DTE_DCE>
0
1
2
None
Xon/Xoff local
CTS
AT+IFC?
Displays the selected values
Displays the supported values
AT+IFC=?
Notes:
None
Result codes:
OK
ERROR
5.1.62 AT+ILRR – Display local report rate
This parameter setting determines whether or not an intermediate result code of local rate is reported
at connection set-up. The rate is applied after the final result code is transmitted to/ from the modem.
Enter
Response
AT+ILRR=0
AT+ILRR=1
AT+ILRR?
Disables reporting of local port rate
Enables reporting of local port rate
Displays the current selected value
Notes:
None
Result codes:
OK
ERROR
+ILRR<speed>
5.1.63 AT+IPR – Set terminal equipment data rate
This command is used to set the data rate between the modem and the interfacing equipment.
Enter
Response
AT+IPR=<speed>
Where speeds supported are 300, 600, 1200, 2400, 4800, 9600,
19200, 28800, 38400, 57600
AT+IPR?
Displays the current selected values
Displays the supported values
AT+IPR=?
Notes:
None
Result codes:
OK
ERROR
ME 820047
Page 32
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.64 CME ERROR<n>
<n>
0
Phone failure
3
4
Operation not allowed
Operation not supported
SIM not inserted
SIM PIN required
SIM PUK required
SIM failure
Incorrect password
Dial string too long
No network service
10
11
12
13
16
26
30
5.1.65 CMS ERROR<n>
<n>
0 – 127
128 – 255
300
GSM 04.11 values
GSM 03.04 values
ME failure
301
302
303
304
305
310
SMS service of ME reserved
Operation not allowed
Operation not supported
Invalid PDU mode parameter
Invalid text modem parameter
SIM not inserted
311
312
313
SIM PIN necessary
PH-SIM PIN necessary
SIM failure
314
SIM busy
315
SIM wrong
320
Memory failure
321
322
Invalid memory test
Memory full
330
331
332
SMSC address unknown
No network service
Network timeout
500
Unknown error
Issue 1.0
03/00
ME 820047
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.1.66 S Register Summary
Register
Function
Default
Value
S0
S1
S2
S3
S4
S5
S6
S7
S8
Rings to auto answer
Ring counter
Escape character
CR character termination character
LF character
Backspace character
Pause before blind dialling
Wait time for carrier
Sets number of seconds to wait when comma dial modifier
encountered in dial string
Wait time before disconnection
Escape code guard time
0
0
43
13
10
8
2
60
2
S10
S12
15
10
S0 Rings to auto-answer
Defines the number of rings before auto-answering an incoming call. Setting the S0 register to zero
will disable the auto answering.
S1 Ring counter
Contains the number of rings the modem has detected. The register is cleared when no rings occur
for 8 seconds, or when the value becomes equal to S0.
S2 Escape character
S2 contains the decimal value of the ASCII character used as the escape character. The default value
corresponds to an ASCII <+>. The value 127 disables the escape process.
S3 CR character
Sets the command line and result code terminator character. Affects asynchronous operation only.
S4 LF character
Sets the character recognised as a line feed. Affects asynchronous operation only.
S5 Backspace character
Sets the character recognised as backspace. Affects asynchronous operation only.
S6 Pause before blind dialling
The value of this register is ignored.
S7 Wait time for carrier
After dialling, this register sets the time the modem must wait before hanging up if it fails to detect the
remote carrier. Time is in seconds.
S8 Wait time before dialling
Sets the number of seconds to wait when comma dial modifier encountered in dial string.
S10 Wait time before disconnection
Sets the number of tenth of seconds to wait before disconnecting after the modem has indicated the
absence of received line signal.
S12 Escape code guard time
Defines the maximum silence time, in fiftieths of a second, accepted between two characters in an
escape sequence.
ME 820047
Page 34
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
5.2 Summary
This section has listed all of the AT commands, which are used by the modem.
Issue 1.0
03/00
ME 820047
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
ME 820047
Page 36
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
6 DEBUGGING & INDICATOR LIGHTS
The modem has a built-in indicator, which can show Red, Green or Yellow and flashes at different
speeds according to the status of the modem and battery.
RED:
GREEN:
YELLOW:
Not connected to the network, or low battery.
Connected to the network.
Battery discharging.
Note
: In order to extend the battery life, the modem will discharge the battery once a month and then
recharge it to full capacity. This process takes around 30 minutes, during which time the modem is
not accessible. After around 45 minutes, the battery will be fully charged.
The indicator flashes with the following information:
Normal
In Service
One Flash, Off, One Flash
Information
Missed calls, low battery,
SMS messages etc.
Two Flashes, Off, Two Flashes
Alert
Incoming call
Four Flashes, Off, Four Flashes
6.1 Summary
This section has described the indicator functions on the MM-6854 modem.
Issue 1.0
03/00
ME 820047
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
ME 820047
Page 38
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
7 INSTALLATION
7.1 Introduction
This is an area, which is often overlooked and is, in fact, very important.
Cost and corner cutting are frequently observed in installations and, consequently, reliability suffers
and problems are seen.
We can only offer a few suggestions in this document, however, expert help is available from a
number of experienced installation companies. Knowledge of the vehicle in which the equipment is
being installed is invaluable.
7.2 Antennas
The majority of GSM antennas do not require an additional ground plane. However, it is important that
any antennas are installed in the best possible location and, if necessary, provided with a suitable
ground plane.
The CA8401 antenna, which Maxon sell as an accessory, is designed for mounting inside of the
vehicle. This avoids any problems with car washes or vandalism. Mounting instructions are provided
with the aerial.
Ideally, multiple antennas should be separated by a minimum of a wavelength (at the lowest
frequency), whilst still retaining a good ground plane for each antenna. For instance, for a 400MHz
antenna, the ideal separation should be a minimum of 0.75m from any other antenna.
With the use of composite materials, especially on trucks, materials may have to be used to fabricate
a suitable ground plane, if required.
Note
: It is important that the antenna ground is not connected to the modem ground. This will not
happen where through-glass antennas are used. Antennas, which are through-chassis mounting and
connect to the vehicle chassis should not be used. Failure to observe this may result in damage to the
unit and will invalidate the warranty.
7.3 Power Sources
It is important that a “clean” source of power is used for the supply to the modem. Ideally, this is
achieved by taking the supply directly from the battery terminals. With modern vehicles, getting
access to the battery is very difficult and therefore alternative sources have to be found. The next best
source is the main fuseboard and then around the steering column.
Frequently, either a large voltage glitch, or total loss of voltage may be observed on some trucks at
start-up. The loss of voltage to the GSM data modem is avoided by the use of an internal battery.
It is recommended that star earthing is used for all connections to the –ve terminal of equipment. This
avoids the possibility of earth loops.
The power supply should be in the range of +9V to +28VDC.
Maxon can supply, as an accessory, a mains power supply which is capable of powering
MM-6854 modems. This power supply has the part number CA6823 and is a 12V, 1A power supply.
7.4 Fusing
It is strongly suggested that fuses for the data modem, and any associated equipment, are located in a
place away from the main fusebox. This is to avoid the possibility of the fuses being “borrowed” by the
driver for other uses.
A 500mA anti-surge fuse should be used for +12V powering or a 800mA anti-surge fuse used for
+24V powering.
Issue 1.0
03/00
ME 820047
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
7.5 Cabling
Maxon provides a variety of accessories (see Section 8.4) which we recommend are used to interface
to the data modem.
The CA8360 interfaces the power and DTR line to the modem.
The CA8361 interfaces the RS-232 connection to the modem.
Alternative, custom made, cables can be produced to customer’s requirements for volume orders.
Please contact Maxon for further details.
The use of the correct cables removes the need for multiple connections and the possibility of the
wireman making an error.
If possible, run RF cables separately from other cables and keep RF cables apart from one another to
avoid interference / coupling.
7.6 Fixing
We recommend that the MM-6854 data modem is securely fixed to a surface, either directly, or with a
suitable bracket.
The fixing hole dimensions are shown below:
163m m
2 off hole s 6.7m m dia .
Figure 7-1 - Fixing centres for MM-6854 modem
Note:
not
recommend that the data modem is fixed by cable ties to any wiring looms.
We do
ME 820047
Page 40
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
7.7 Connections
7.7.1 9 pin D-type (RS-232 Interface)
Pin Function
1
2
3
4
5
6
7
8
9
DCD
TXD
RXD
DTR
GND
DSR
RTS
CTS
RI
Table 7-1 - 9 pin D-type socket connections
7.7.2 25 pin D-type
Pin Function
1
GND
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Software update supply 5.2 to 7.2V
Software update programming voltage 0 – 5.2V
Software update serial data Rx 0 – 3 V
Software update serial data Tx 0 – 3 V
Reserved for future use
Reserved for future use
Reserved for future use
Reserved for future use
GND
Reserved for future use
Reserved for future use
GND
GND
Ignition (active low)
Power Supply (+9 to +28VDC)
Power Supply GND
Reserved for future use
Reserved for future use
Reserved for future use
Reserved for future use
Reserved for future use
Reserved for future use
Reserved for future use
Reserved for future use
Table 7-2 - 25 pin D-type plug connections
7.8 Summary
This section has briefly covered the installation of the MM-6854 data modem.
Issue 1.0
03/00
ME 820047
Page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
ME 820047
Page 42
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8 APPENDICES
8.1 Setting up Windows Modem interface
Follow these step-by-step instructions to set up the Windows Modem interface for use with TAPI
interface software (such as WinFax Pro).
8.1.1 Open up the Control Panel
8.1.2 Double click on the modem icon
Issue 1.0
03/00
ME 820047
Page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.1.3 Highlight the don’t detect my modem box
8.1.4 Select the standard 19200 modem
ME 820047
Page 44
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.1.5 Select the appropriate COM port
8.1.6 Set the location information
Issue 1.0
03/00
ME 820047
Page 45
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.1.7 Finish Installation
8.1.8 Select Properties
ME 820047
Page 46
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.1.9 Select Connection
8.1.10 Set Data Bits, Parity and Stop bits
Select Advanced
Issue 1.0
03/00
ME 820047
Page 47
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.1.11 Select Flow Control and Software (XON/XOFF)
Note
: Some applications do not use Software Flow Control, therefore set flow control to Hardware.
must
In whichever case, the hardware or the software
provide flow control otherwise data will be lost.
8.1.12 RS-232
In order to turn on the modem, Pin 4 (DTR) must be pulled high. This pin will normally be high on a
PC COM port when the COM port is available.
ME 820047
Page 48
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.2 Setting up Hyper Terminal
Hyper Terminal is a very simple terminal package which can be used to send simple commands to /
from the modem.
8.2.1 Select Hyper Terminal from Programs Menu
Issue 1.0
03/00
ME 820047
Page 49
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.2.2 Select Hyper Terminal
Double click to open Hyper Terminal.
8.2.3 Select Properties
ME 820047
Page 50
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.2.4 Set Port
8.2.5 Port Settings
Issue 1.0
03/00
ME 820047
Page 51
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.2.6 Properties
Set Beep, if required.
8.2.7 ASCII settings
Append line feeds, send line ends and wrap lines, if required.
ME 820047
Page 52
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.3 Setting up Win Fax Pro
The following section illustrates how to set up Win Fax Pro. Other Fax software is available and this
section should not be taken as an endorsement of Win Fax Pro.
8.3.1 Communication Setup
Ensure that the computer modem settings are set to 19200,8,n,1, see Sections 10.1.9 and 10.1.10.
8.3.2 Win Fax Pro Setup
With Win Fax Pro Installed, setup the modem as follows:
Under Program Setup, select Properties
Issue 1.0
03/00
ME 820047
Page 53
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
Check Modem is Standard 19200, if not, go to 10.1.4. Select Properties
Check that the following setting are made:
ME 820047
Page 54
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
8.4 Accessories
Description of Accessory
Maxon Part
Number
5 metre Power Lead
CA8360
CA8361
CA8401
CA6823
ME440014
9 way D-type Male to Female RS-232 Interface Lead
Dual-band GSM Antenna for in-vehicle mounting
12V 1 Amp Mains Power Supply fitted with Euro connector
Euro Connector to UK adapter
Issue 1.0
03/00
ME 820047
Page 55
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
ME 820047
Page 56
Issue 1.0
03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
MM6854/64 Dual Band GSM Data Modem
9 GLOSSARY
Abbreviation
Meaning
AT
Hayes AT modem serial command set
commonly used for land line modems
Command Interpreter.
CI
DTE
DTR
GPS
GSM
I/O
Data Terminal Equipment
Data Terminal Ready
Global Positioning System
Global System Mobile
Input / Output
LED
SIM
SMS
SMSC
Light Emitting Diode
Subscriber Identity Module
Short Message Service
Short Message Service Centre
Issue 1.0
03/00
ME 820047
Page 57
Download from Www.Somanuals.com. All Manuals Search And Download.
|