Marshall electronic Flat Panel Television V R82DP HDA User Manual

Marshall Electronics  
1910 East Maple Ave.  
El Segundo, CA 90245  
Tel.: 800-800-6608 • 310-333-0606  
Fax: 310-333-0688  
SDI: 525i/60hz 4x3  
OSD  
Use SELECT to enable the On Screen Display  
for input and function status  
V-R82DP-HDA Users Guide  
Blue Only  
SELECT to adjust SMPTE or split eld color bars.  
1. Allow monitor to warm up for 5-10 minutes minimum.  
2. Display SMPTE color bars on monitor. Turn on off Color with control.  
3. Find the PLUGE (superblack, black, and gray bars) at the lower right  
of the pattern.  
Adjust BRIGHTNESS until there is no difference visible between the super-  
black and black bars, but is still visible.  
4. Adjust CONTRAST control to achieve a balanced gray scale across  
top bars.  
5. Turn up CHROMA (color level) control until the two outermost bars  
(white and blue appear to match in brightness.  
6. NTSC Only -Adjust COLOR PHASE (tint or hue) control until the third  
bar from the left (cyan) and the third bar from the right (magenta) appear to  
match in brightness.  
Product Overview  
Features  
1
2
3
10  
Warranty  
Marshall Electronics warranties to the first consumer, that this V-R82DP-HDA Dual 8.4-inch LCD rack mounted monitor set will, under  
normal use, be free from defects in workmanship and materials, when received in its original container, for a period of one year from the  
purchase date.  
This warranty is extended to the purchasing end user only and proof of purchase is necessary to honor the warranty. If there is no proof  
of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore,  
labor and parts may be charged to you.  
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifica-  
tions in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any war-  
ranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time  
period described above.  
An extra note about LCD displays: It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of  
the display active viewing area. Marshall Electronics has the option to reserve service for display pixel failure if deemed unobtrusive to  
effective use of the monitor by our technicians.  
Video - Screen Formats and Frame Rates  
Electrical Specifications  
Mechanical Specifications  
Operational Setup  
4
5
6
Connectors  
7
8
9
Switch Settings, Adjustments and Indicators  
Menu Functions  
Due to constant effort to improve products and product features, specifications may change without notice.  
Warranty  
10  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
6
Mechanical Specifications  
Dimensions  
19.12” w x 7” h x 1.5” d (485.7mm x 220.22mm x 38.1mm)  
8
Switch Settings, Adjustments and Indicators  
V-R82DP-HDA Weight  
V-PS12-5V-1 Power Supply Weight  
5.5 lbs (2.4 kg)  
1 lbs (0.45kg)  
Tally Lamps  
Operational Setup  
1. Unpack the V-R82DP-HDA and accompanying V-PS12-5V-1 power supply. Physically inspect for any damage that may have oc  
curred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608.  
If you are not located within the continental United States call +1 310-333-0606.  
2. After inspection, install in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is required when  
installed to prevent possible damage to the V-R82DP-HDA internal components.  
3. Connect required cables for signal input and output. Please note that power must be applied to the V-R82DP-HDA for all outputs to  
be activated. All BNC connectors should be rated for 75Ω.  
4. Plug the V-PS12-5V-1 power supply into the A.C. source  
5. Attach twist lock power connection from V-PS12-5V-1 power supply to the back of the unit.  
6. Turn on each of the V-R82DP-HDA screens by depressing the power switch located on the front of the unit for each screen.  
Connectors  
7
Tally IN  
DB-15 Female  
* Component Inputs comply to SMPTE274M, 294M,295M,296M  
* Composite Video Inputs comply to SMPTE-170M  
* Tally lamps active when connected to ground  
Pin1-M2Yel  
Pin9-  
Pin2-M2Red Pin10-  
Pin3-M2Grn  
Pin4-  
Pin5-Gnd  
Pin6-  
Pin11-M1Yel  
Pin12-M2Red  
Pin13-M3Grn  
Pin14-  
Pin7-  
Pin15-Gnd  
S-Video Out  
S-Video In  
4 Pin Din (Female) 4 Pin Din (Female)  
Pin1 - GND  
Pin2 - GND  
Pin3 - Yout  
Pin4 - Cout  
Pin1 - GND  
Pin2 - GND  
Pin3 - Yin  
Pin4 - Cin  
12 VDC from  
V-PS12-5V-1 power supply  
Left Pin - Pos  
Right Pin- Neg  
Dry Erase Label  
Active Outputs require power to be applied  
All input signals appear as output signal  
Analog output signals are buffered and amplied  
Image Adjustment Controls  
Note: Tint only functions when NTSC  
Video or S-Video are selected  
Screen aspect ratio switch 4:3 or 16:9 selector and indicators  
DVI-I Connector  
Pin#  
Pin#  
Signal  
Signal  
1
2
3
T.M.D.S DATA 2-  
T.M.D.S DATA 2+  
T.M.D.S DATA 2/4  
SHIELD  
16  
17  
18  
HOT PLUG DETECT  
T.M.D.S DATA 0-  
T.M.D.S DATA 0+  
4
T.M.D.S DATA 4-  
19  
T.M.D.S DATA 0/5  
SHIELD  
5
6
7
T.M.D.S DATA 4+  
DDC CLOCK  
DDC DATA  
20  
21  
22  
T.M.D.S DATA 5-  
T.M.D.S DATA 5+  
T.M.D.S CLOCK  
SHIELD  
T.M.D.S CLOCK+  
T.M.D.S CLOCK-  
VGA/XGA Connector  
PIN#  
SIGNAL  
RED  
PIN#  
9
SIGNAL  
NC  
NC  
NC  
NC  
HSYNC  
VSYNC  
NC  
4:3 Aspect  
16:9 Aspect  
1
2
3
4
5
6
7
8
8
9
10  
11  
ANALOG VERT. SYNC  
T.M.D.S DATA 1-  
T.M.D.S DATA 1+  
T.M.D.S DATA 1/3  
SHIELD  
T.M.D.S DATA 3-  
T.M.D.S DATA 3+  
+5V POWER  
23  
24  
GREEN  
BLUE  
NC  
GND  
RED SHIELD  
GREEN SHIELD  
BLUE SHIELD  
10  
11  
12  
13  
14  
15  
C1  
ANALOG RED  
12  
13  
14  
15  
C2  
C3  
C4  
C5  
ANALOG GREEN  
ANALOG BLUE  
ANALOG HORZ SYNC  
ANALOG GROUND  
GND  
MarshallElectronics  
V-R82DP-HDA Users Guide  
3
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 2 / Video Signals Displayed via DVI and YPrPb connections  
(x=not available) (HDMI requires adapter to DVI)  
Table 1 / Computer Signals Displayed via DVI and VGA connector  
DVI-D  
VGA  
16x9  
Y Pr Pb  
DVI  
Input Signal Type  
and aspect  
Input Signal Type  
and aspect  
4x3  
16x9  
4x3  
4x3  
16x9  
4x3  
16x9  
640 x 480 60Hz  
640 x 480 75Hz  
640 x 480 85Hz  
800 x 600 60Hz  
800 x 600 75Hz  
800 x 600 85Hz  
1024 x 768 60Hz  
1024 x 768 75Hz  
1024 x 768 85Hz  
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
720 x 486 60i  
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
x
x
x
x
720 x 576 50i  
1280 x 720 60P  
1280 x 720 50P  
1280 x 720 30P  
1280 x720 29.97P  
1280 x720 25P  
1280 x 720 24P  
1280 x 720 23.98P  
1920 x 1080 60i  
1920x1080 59.94i  
1920 x 1080 50i  
1920 x 1080 30P  
1920x1080 29.97P  
1920 x 1080 25P  
1920 x 1080 24P  
1920 x 1080 24Psf  
Y
Y
x
Y
Y
x
x
x
x
x
x
x
x
x
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Marshall Electronics  
V-R82DP-HDA Users Guide  
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.  

KTI Networks Switch KSD 103 A Series User Manual
Kuppersbusch USA Coffeemaker EKV 66000 User Manual
KWC Indoor Furnishings K12VB42700A26 User Manual
Kyocera All in One Printer FS 1714M User Manual
LG Electronics Cell Phone UX245 User Manual
LG Electronics Computer Drive GMA 4020B User Manual
Lindy Computer Drive SD CBALINEC 4E6I User Manual
Makita Nail Gun BPT351 User Manual
Marvel Industries Refrigerator 3SBARE User Manual
MicroBoards Technology Label Maker GX Disc Printer User Manual