1
9 / ”
4
1
12 / ”
2
11”
FILE #E21609
3
10 / ”
4”
8
SRA-DS Series Model B
1”
Fan Forced Wall Heaters
Installation & Maintenance Instructions
Dear Owner,
Congratulations! Thank you for purchasing this new heater manufactured by a division of Marley
Engineered Products. You have made a wise investment selecting the highest quality product in the heat-
ing industry. Please carefully read the installation and maintenance directions shown in this manual.
You should enjoy years of efficient heating comfort with this product from Marley Engineered Products...
the industry’s leader in design, manufacturing, quality and service.
... The Employees of
Marley Engineered Products
WARNING
!
5. Do not insert or allow foreign objects to enter any ventilation
Read Carefully - These instructions are written to help
or exhaust opening as this may cause an electric shock,
you prevent difficulties that might arise during installation
fire,or damage to the heater.
of heaters. Studying the instructions first may save you
considerable time and money later. Observe the following
6. Do not block air intakes or exhaust in any manner. Keep com-
bustible materials, such as crates, drapes, etc., away from
procedures, and cut your installation time to a minimum.
heater. Do not install behind doors, furniture, towels, or
To reduce risk of fire or electric shock:
boxes.
1. Disconnect all power coming to heater at main service panel
7. Aheater has hot and arcing or sparking parts inside. Do not
before wiring or servicing.
use it in areas where gasoline, paint or flammable liquids are
2. All wiring must be in accordance with the National and Local
stored.
Electrical Codes and the heater must be grounded as a pre-
8. Use this heater only as described in this manual. Any other
caution against possible electric shock.
use not recommended by the manufacturer may cause fire,
3. Verify the power supply voltage coming to heater matches the
electric shock, or injury to persons.
ratings printed on the heater nameplate before energizing.
9. This heater is not approved for use in corrosive atmospheres
4. This heater is hot when in use. To avoid burns, do not let bare
such as marine, green house or chemical storage areas.
skin touch hot surfaces.
SAVE THESE INSTRUCTIONS
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4
MAINTENANCE AND CLEANING
INDICATOR
LIGHT
Your heater is designed for years of trouble-free operation and requires no
special maintenance other than occasional cleaning. The motor is perma-
nently lubricated.
Once each year, the heater should be cleaned to remove dust and other
foreign material which has collected during the heating season, as follows:
Figure 3
INSTALLATION OF FRONT COVER (GRILLE) AND
THERMOSTAT KNOB
1. Position the front cover so the four (4) holes on the side align
1. Turn power off at main switch.
2. Remove thermostat knob.
with the tabs on the plastic pieces of the heat deck.
3. Remove front cover by depressing plastic tabs with a flat
bladed screwdriver as shown in Figure 4. Release both tabs
on one side then rotate cover off of heater assembly.
4. Use vacuum cleaner with brush attachment to remove dust and dirt
that has accumulated in heater (especially around element and fan
blade). Do not use water or any cleaners to clean heater compo-
nents.
2. Hook the front cover over the tabs on one side then rotate
the front cover into place making sure that all four tabs are
snapped onto the front cover.
3. Fit the thermostat knob onto the thermostat shaft and push
into place.
5. Replace grille and thermostat knob.
6. Wipe grille clean with a damp cloth. DO NOT use waxes or any
cleaners that leave a residue since these may discolor during heater
operation.
HEATER CHECKOUT AND OPERATION
1. After heater is completely assembled, push the disconnect
switch to the “on” position and rotate thermostat knob coun-
terclockwise until control stops. This is the minimum heat
setting.
7. Turn the main line switch on at the switch panel to restore power to
heater. The heater is now ready for another season of operation.
OPERATIONAL NOTICE
2. Turn power supply to heater “ON” at main switch panel.
Your heater is equipped with an automatic reset high limit control that
will automatically turn the heater off to prevent a fire if the heater over-
heats. Should this occur, the indicator light will illuminate and will contin-
ue to shine until the limit resets.
3. Heater should not operate. If it operates, disconnect power
and re-check wiring.
4. Rotate thermostat clockwise until it stops (maximum heat
setting) and wait at least 2 minutes. Fan control will delay
fan coming on until element is warm.
CAUTION
!
THE ILLUMINATED INDICATOR LIGHT SIGNIFIES THE HEATER
HAS BEEN SUBJECTED TO SOME ABNORMAL CONDITION.
CHECK HEATER TO INSURE THAT IT HAS NOT BEEN BLOCKED IN
ANY MANNER (IF SO, REMOVE BLOCKAGE). IF THERE IS NO
INDICATION OF BLOCKAGE, IT IS RECOMMENDED THE HEATER
BE CHECKED BY A REPUTABLE ELECTRICIAN OR REPAIR SER-
VICE TO INSURE THE HEATER HAS NOT BEEN DAMAGED.
5. If heater and fan do not come on, disconnect power and
check wiring.
6. Allow heater to continue to operate until room temperature
reaches desired comfort level. Then rotate thermostat knob
counterclockwise slowly until thermostat clicks off. Fan will
continue to operate for a minute or so until element cools.
7. It may be necessary to readjust thermostat a time or so until
exact comfort level is attained. Rotation in the clockwise
direction will increase the amount of time the heater will pro-
duce heat. Rotation in the counterclockwise direction will
reduce the amount of time the heater is on.
NOTE: For best results, the heater should be left “ON” constantly during
the heating season as the thermostat, when properly set, will maintain the
desired temperature. In the full counter-clockwise position the heater will
remain off until the room temperature drops well below freezing.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
Specifications
MODEL
NO.
VOLTS AMPS
WATTS
BTU/HR
WIRE
SIZE
8.40
4.20
1000
500
3413
1706
SRA1012DSB
120
120
14AWG
12.50
6.25
1500
750
5120
2560
SRA1512DSB
SRA1812DSB
12AWG
12 AWG
120
240
15.0
1800
6143
8.40
4.20
7.30
3.61
2000
1000
1500
750
6826
3413
5120
2560
SRA2024DSB
SRA2027DSB
SRA1527DSB
14AWG
14AWG
14AWG
208
277
240
7.30
3.61
6.25
3.20
2000
1000
1500
750
6826
3413
5120
2560
NAMEPLATE
MODEL NO.
SRA2024DSB
DATE CODE
0695
277
240
5.5
2.75
4.7
1500
750
1125
562
5120
2560
3840
1920
SMALL ROOM FAN FORCED HEATERS
2000/1000W @ 240VAC 60HZ
1500/750W @ 208VAC 60HZ
2.35
SRA****IF
SRBB
774G LISTED
ROOM HEATER
Inner Frame (Fan Deck Assembly & Grille) Only
MUST BE USED WITH SR-BB BACK BOX.
DO NOT OPERATE WITHOUT SR-FC
SERIES FRONT COVER IN PLACE.
Back Box Only - For All Above Heaters
Surface Mounting Frame (Accessory) Order Separately
12-1/2”H X 10-3/8”W X 4”D
2” Recess Mounting Frame (Accessory) Order Separately
12-1/2”H X 10-3/8”W X 2”D
SRASM
SRAS2
SRAS1
MARLEY ENGINEERED PRODUCTS
BENNETTSVILLE, SC 29512
1”Recess Mounting Frame (Accessory) Order Separately
12-1/2”H X 10-3/8”W X 1”D
399726043
SRADS
20 Amp-2 Pole Disconnect Switch Kit (Accessory) Order Separately
Tamper Proof Front Cover (Accessory Order Separately)
SRAFCTP
LIMITED WARRANTY
All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of
installation, except heating elements which are warranted against defects in workmanship and materials for five years from date of installation. This
warranty does not apply to damage from accident, misuse, or alteration; nor where the connected voltage is more than 5% above the nameplate
voltage; nor to equipment improperly installed or wired or maintained in violation of the product’s installation instructions. All claims for warranty work
must be accompanied by proof of the date of installation.
The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred
to return products to Marley Engineered Products Service Center.Within the limitations of this warranty, inoperative units should be returned to the
nearest Marley authorized service center or the Marley Engineered Products Service Center, and we will repair or replace, at our option, at no charge
to you with return freight paid by Marley. It is agreed that such repair or replacement is the exclusive remedy available from Marley Engineered
Products.
THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. AND ALL IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY
DISCLAIMED AND EXCLUDED FROM THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALL NOT BE LIABLE FOR CONSEQUEN-
TIAL DAMAGES ARISING WITH RESPECT TO THE PRODUCT, WHETHER BASED UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CON-
TRACT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328.
Merchandise returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley
Engineered Products. When requesting return authorization, include all catalog numbers shown on the products.
HOW TO ORDER REPAIR PARTS
In order to obtain any needed repair or replacement
parts, warranty service or technical information, please
contact Marley Engineered Products Service Center toll-
free by calling 1-800-642-HEAT.
When ordering repair parts, always give the informa-
tion listed as follows:
SPX Corporation
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA
1. The Part Number
2. The Model Number
3. The Part Description
4. Date of Manufacture
ECR 35194
Part No. 5200-2181-005
03-02
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|