TM
UniVerse Skillet
ELECTRIC FRYING & BRAISING PAN
TECHNICAL MANUAL
COVERING:
• Installation
• Operation
MODELS:
30-STEL, 30-STEL-LX, 40-STEL, 40-STEL-LX,
30-STEM, 30-STEM-LX, 40-STEM, 40-STEM-LX
• Service and Parts
WARNING:
Improper Installation, adjustment, alteration, service, or
maintenance can cause property damage, injury, or death. Read the
installation, operating, and maintenance instructions thoroughly before
installing or servicing this equipment.
In a prominent location, post
instructions to be followed in
the event the user smells gas.
This information shall be
obtained by consulting the
local gas supplier.
FOR YOUR SAFETY:
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
35 Gravey Street l Everett l MA l 02149
Tel: (617) 387-4100 l Fax: (617) 387-4456 l Outside Fax: 1-800-227-2659
Form Number: S-2468 Rev. B
07/04 Printed in the U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUMMARY OF SAFETY NOTICES
MODELS: 30-STEL, 30-STEL-LX, 40-STEL, 40-STEL-LX, Open-Leg Electric UniVerse Skillet
30-STEM, 30-STEM-LX, 40-STEM, 40-STEM-LX, Modular Electric UniVerse Skillet
The following general safety notices supplement the specific warnings
CAUTION: Do not install in such a manner that the service
person cannot remove the control box cover.
and cautions contained in this technical manual. They are recomm-
ended precautions that must be understood and adhered to during the
installation, operation, and maintenance of these electrically operated
appliances.
Supply wires must be suitable for temperature of at least 90°C.
Additionally, all wiring must conform to the requirements of local and
national electric codes. Conduit and fittings should be watertight type.
WARNING:
Do not get water on wiring in controls. Be sure to wash inside of
skillet pan, inside of cover including under drip-lip, and pouring
spout area.
Unit is equipped with an interlock switch that shuts off gas to the
burners when skillet pan is more than 10° above normal horizontal
cooking position.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1 GENERAL INFORMATION
JOB NAME: __________________________
ITEM NO.: ___________________________
NO. REQUIRED: ______________________
UniVerse ELECTRIC
TILTING SKILLET
E
MODELS: 30-STEL, 30-STEL-LX, 40-STEL, 40-STEL-LX, Open-Leg Electric UniVerse Skillet
30-STEM, 30-STEM-LX, 40-STEM, 40-STEM-LX, Modular Electric UniVerse Skillet
MODEL: m 30-STEM
m 30-STEL
m 40-STEL
m 40-STEM
SIZE:
m 30-STEL - 33" Wide x 33" Front-to-Back
(838mm Wide x 838mm Front-to-Back)
Height - Cover Closed- 41” (1041mm)
Height - Cover Opened - 72” (1828mm)
m 30-STEM - 36" Wide x 33" Front-to-Back
(914mm Wide x 838mm Front-to-Back)
Height - Cover Closed- 41” (1041mm)
Height - Cover Opened - 72” (1828mm)
m 40-STEL - 45" Wide x 33" Front-to-Back
(1143mm Wide x 838mm Front-to-Back)
Height - Cover Closed- 41” (1041mm)
Height - Cover Opened - 72” (1828mm)
30-STEM Shown
m 40-STEM - 48" Wide x 33" Front-to-Back
(1219mm Wide x 838mm Front-to-Back)
Height - Cover Closed- 41” (1041mm)
Height - Cover Opened - 72” (1828mm)
operated manually with a collapsible hand crank. Power
tilting is also available. Both tilting methods allow
complete emptying of contents under positive control.
DESCRIPTION:
Operation: The UniVerse Tilting Skillet™ Models 40-
STEM and 40-STEL will be rated at 18 kw. Models 30-
STEM and 30-STEL will be rated at 12 kw. All models are
available in 208V, 240V 1- and 3-phase, or 480V 3-phase.
tilting is also available. Both tilting methods allow
complete emptying of contents under positive control.
The Market Forge Electric UniVerse Tilting Skillets™ are
available in 30-gallon (87-liter) and 40-gallon (114-liter)
pan bodies with 12 kw and 18 kw inputs, respectively.
Both models are available in open-leg and closed-base
frame assemblies with manual or power tilt capabilities.
Benefits: Our UniVerse Skillets, unlike those of other
braising pan manufacturers that use clad plates,
incorporate a uni-pan design. This design reduces the
potential for leaks and eliminates the possibility of pitting
and surface rusting. The new center-of-gravity tilting
allows for safe use of caster mounting. Our power tilt
operates smoothly, with manual override that works easily
when needed, without the use of electric drills required by
other manufacturers.
TECHNICAL SPECIFICATIONS:
Cooking Pan: The unitized cooking pan has no bottom
welds and is reinforced to resist cracking as expansion
and contraction occur. The textured cooking surface is
machine-applied for a long-wearing, good appearance.
The cooking pan incorporates an easy-pour lip and 5-
gallon increment markings. Gas flames are applied to
finned aluminum extrusions bolted to the underside of the
cooking pan for better heat transfer. An interlock switch
will turn off the heaters beyond 10" tilt.
Construction: The UniVerse Skillet has a textured
stainless steel cooking surface with reinforcement.
Heating elements turn off automatically when the cooking
pan is raised to a tilted position. The skillet is provided with
a heavy-duty gas shock assisted cover with condensate
vent. The cooking pan and cover are mounted to a
11/2” (38 mm) square stainless steel tube frame,
permitting access to floor for easy cleaning. The closed-
base model incorporates easily removable stainless steel
panels on the front and left sides. The cooking pan tilts to
a full 93°. This is accomplished by a gear mechanism
Controls: The UniVerse Tilting Skillet™ comes standard
with a solid-state temperature controller with a positive off
position and 100°– 450° Fahrenheit scale, a pilot light to
indicate when the electric heaters are on, and a 1-hour
mechanical timer. Optional power tilting mechanism also
utilizes an up/down rocker switch. Manual tilting
mechanism uses a collapsible hand crank located below
the control panel. A high-limit temperature control is also
provided. The control housing shall be water-
resistant/splash-proof.
The manufacturer reserves the right to modify materials and specifications without notice
An Employee Owned Company
Printed in U.S.A.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1 GENERAL INFORMATION
UniVerse ELECTRIC
DETAILS & DIMENSION
E
TILTING SKILLET
MODELS: 30-STEL, 30-STEL-LX, 40-STEL, 40-STEL-LX, Open-Leg Electric UniVerse Skillet
30-STEM, 30-STEM-LX, 40-STEM, 40-STEM-LX, Modular Electric UniVerse Skillet
OPTIONS: Optional at Extra Cost:
m Power tilt mechanism
m 1 1/2” Tangent draw-off valve
m Single Pantry Hose
ELECTRICAL CHARACTERISTICS:
m Pan support
m Single Faucet
m Double Faucet
m Caster kit
Power Supply: See chart to right for total amp draw.
Use wire suitable for 90°C. A stepdown
transformer provides power to the 120V
control circuit.
m Double Pantry Hose
m Strainer relief kit
m Removable liquid strainer
m 2" Tangent Draw-Off Valve
m 480 Volt
Details of other electrical systems are
available upon request
______________________________________________
40-STEM & STEL = 18kW / 30-STEM & STEL= 12kW
______________________________________________
m 12” x 20” pan holder inserts (pan not included)
INSIDE DIMENSIONS:
m 30-STEM & 30-STEL
Volts
208
240
1pH
87
75
--
3pH
58
1pH
33
29
14.5
3Ph
50
43
22
30 1/4" Wide x 9" Deep x 25. 3/4" Front-to-Back
(768mm Wide x 228mm High x 654mm Front-to-Back)
Height When Cover Closed- 41” (1041mm)
Height When Cover Opened - 72” (1828mm)
50
--
480*
______________________________________________
* 3 pH Only
m 40-STEM & 40-STEL
WATER CONNECTIONS:
42 1/2" Wide x 9" Deep x 25. 3/4" Front-to-Back
(1073mm Wide x 228mm High x 654mm Front-to-Back)
Height When Cover Closed- 41” (1041mm)
Height When Cover Opened - 72” (1828mm)
Cold Water: 3/8” NPT to cold water faucet
Hot Water: 3/8” NPT to hot water faucet
Water Pressure Requirements: 50 PSI (3.5 kg/cm2)
Max: 25 PSI (1.8 kg/cm2) min.
SKILLET PAN CAPACITY:
Water connections are optional when required.
40-STEM & STEL 30-STEM & STEL
• 40 gallons (152 liters)
• 30 gallons (114 liters)
CONNECTIONS:
EP = Electrical power connection
HW = Hot water
CW
1.5"
1"
38mm
25mm
POUR
PATH
CW = Cold water
HW
CW
HW
EP
72"
1828mm
45"
1143mm
EP
40"
25"
1016mm
635mm
28"
711mm
41"
1041mm
1.25"
12.5"
30.75mm
9"
FLANGED FEET"
317.5mm
17.5"
Rear hold down feet 3.5" DIA.
W/2 5/16" DIA. bolt holes on 2.5"
DIA. B.C. 180o apart (Secure to floor).
228mm
1.25"
40 Gallon 45"
Model: STEL 1143mm
445mm
7"
30mm
31.5"
177mm
30 Gallon 33"
18"
800mm
Model: STEL 838mm
457mm
33"
40 Gallon 48"
Model: STEM 1219mm
838mm
30 Gallon 36"
Model: STEM 914mm
*It is our policy to build equipment which is design certified by U.L., A.S.M.E., N.S.F. and C.S.A. However, a continuing program of product improvement makes it
necessary to submit new models to the agencies as they are developed and consequently not all models bear the appropriate agency labels at all times.
An Employee Owned Company
Printed in U.S.A.
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2 INSTALLATION INSTRUCTIONS
1. Remove carton from skid, being careful not to dent or
scratch finished surfaces of unit.
TABLES 2.1 AMPS PER LINE PER LINE WIRE
MODELS: 30-STEL, 30-STEL-LX, 30-STEM & 30-STEM-LX
3 pH, 4 Wire, 50Hz Amps Per Line Wire
2. Inspect unit carefully for shipping damage. File claim with
carrier immediately if damage is found.
3. Remove screws holding unit to skid.
10.1kW
12kW
220/380V
240/415V
(EXPORT ONLY)
15
16.7
4. Transfer unit to desired position. Make unit level and
steady by adjusting feet to compensate for floor
irregularities. Secure rear feet to floor by using 5/16"
screws.
12kW, 1 pH, 60Hz Amps Per Line Wire
L #1
52
50
L #2
52
50
208V
240V
NOTE: Do not install in such a manner that service person
cannot remove control box cover.
12kW, 3 pH, 60Hz Amps Per Line Wire
5. Drop down hinged front cover of connection box. Loosen
screws and clips on top of box.
L #1
33
L #2
33
29
L #3
33
29
208V
240V
480V
29
14.5
6. Connect unit to a branch circuit having a voltage and
circuit type specified on name plate and of sufficient size
to carry load. The amps per line per line wire for the
various voltage ratings are shown in Table 2.1 below.
14.5
14.5
MODELS: 40-STEL, 40-STEL-LX, 40-STEM & 40-STEM-LX
NOTE: Supply wires must be suitable for temperature of at
least 90°C. Additionally, all wiring must conform to the
requirements of local and national electric codes. Conduit
and fittings should be watertight type.
3 pH, 4 Wire, 50Hz Amps Per Line Wire
15.1kW
18kW
220/380V
240/415V
23
25
7. Connect ground wire from electrical service to ground lug.
8. Reinstall hinged front cover of connection box securely.
(EXPORT ONLY)
18kW, 1 pH, 60Hz Amps Per Line Wire
L #1
87
75
L #2
87
75
208V
240V
9. Ensure that skillet is firmly seated on frame before
checking connection and functioning of controls.
18kW, 3 pH, 60Hz Amps Per Line Wire
NOTE: Unit is equipped with an interlock switch that shuts
off current to heating elements when skillet pan is more
than 10° above normal horizontal cooking position.
L #1
50
L #2
50
43
L #3
50
43
208V
240V
480V
43
22
22
22
10. Switch on current supply to unit. Check for proper
functioning of controls and heating elements (see
Section 3—Operating Instructions).
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2 INSTALLATION INSTRUCTIONS
98-1256 D
FIG. 2.1 OPTIONAL WIRING FOR ELECTRIC LIFT SKILLET.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2 INSTALLATION INSTRUCTIONS
98-12562 D
FIG. 2.2 ALTERNATE WIRING FOR 220/380V , 240/415V SYSTEM
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2 INSTALLATION INSTRUCTIONS
98-12563 D
FIG. 2.3 ALTERNATE WIRING CONFIGURATION FOR 480V
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3 OPERATING INSTRUCTIONS
INTRODUCTION:
4. Preheat to desired temperature (with cover down) before
grilling, pan-frying, or any other method of cooking except
boiling.
This technical manual contains general information,
installation, operation, principles of operation, troubleshooting
guide, and maintenance information for the electrically NOTE: For best results, allow unit to cycle on/off once.
operated UniVerse Tilting Skillet. Also included is an illustrated
parts list and a directory of authorized parts and service 5. Ensure that cover is up for most types of cooking except for
agencies.
simmering, braising, or boiling. Cover has drip-lip at rear to
direct condensate into skillet.
DESCRIPTION:
6. Remove cooked food immediately to prevent over-cooking.
Tilt skillet by turning handcrank clockwise or pushing tilt
switch.
The Market Forge Industries UniVerse Models 30-STEL
(12 kW input) and 40-STEL (18 kW input) are electrically
operated skillets, tilting type, with 30- and 40-gallon capacities,
respectively. They are equipped with a solid-state thermostat 7. Lower skillet by turning handcrank counterclockwise on
and high-limit control with a 100°F-to-450°F temperature
scale.
pushing tilt switch.
BASIC FUNCTIONS:
SHUT-DOWN:
The UniVerse Tilting Skillet is a very versatile cooking Turn thermostat control knob counterclockwise to off when no
appliance. It can perform basic cooking functions, such as further heating is desired.
braising meat, sautéing, pan-frying chicken, steaming
vegetables, boiling, and simmering. Refer to Section 4—Test CLEANING:
Kitchen Bulletin, which gives detailed information on the
various types of food products that can be cooked in the Unit must be cleaned after each use. Proceed as follows:
skillet.
1. When all food has been removed from skillet, add water to
loosen/dissolve any remaining food.
COOKING:
1. Ensure that electric power connection has been made
correctly and that branch circuit breaker at building supply
box is on.
2. Wash skillet using mild detergent, water and nylon brush. If
food is stuck to skillet surface, soak and use a little heat to
loosen food.
2. Ensure that skillet is in full down position and clean before
using.
WARNING:
Do not get water on wiring or in controls. Be sure to wash
inside of skillet pan, inside of cover including under drip-lip,
NOTE: Electric power automatically shuts off when skillet is and pouring spout area.
tilted more than 10° above normal horizontal cooking position.
3. Rinse and dry entire unit.
3. Set thermostat at desired temperature by turning thermostat
control knob clockwise. See Section 4—Test Kitchen
Bulletin for thermostat settings.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4 TEST KITCHEN BULLETIN
UNIVERSE TILTING SKILLET
COOKING FACTS ON PARADE
1. The UniVerse Skillet is one of the most versatile pieces of equipment to be found in any restaurant or institutional kitchen.
2. This unit will stew, simmer, pan-fry, braise, grill, and sauté—and all with a very uniform heat pattern.
Note: DO NOT ATTEMPT TO DEEP FRY WITH YOUR SKILLET!
3. For best results, the Tilting Skillet should always be preheated and allowed to cycle once.
4. A great deal of heavy lifting and transferring of foods from one pan to another can be eliminated, and, therefore, pot washing will be reduced.
5. This type of equipment usually reduces the total cooking time by as much as 25% on combination dishes.
6. Sauces usually lose less moisture, as the cover reduces evaporation.
7. Large batches of gourmet items can be prepared with less work and with more uniform results.
8. Frozen vegetables can be cooked in the UniVerse Skillet in the serving pan, then removed and transferred directly to the serving line.
9. The following temperatures should be used:
Simmering:
Saut éing:
Searing:
Frying:
Maximum of 200 °F
225 –275°F
300 –350°F
325 –375°F
350 –425°F
Grilling:
10. Temperatures of approximately 200°F should always be used for milk-based products, or scorching will take place. Lower temperatures
(150–175°F) prevent thickening.
11. Some items should be started at a high temperature and then reduced. This permits sealing for about 20% of the time and cooking for the
remaining 80%.
12. The cover has a lip at the back edge that directs the condensate on the cover back into the skillet.
13. The unit tilts easily to 90°, and receiving pan is always approximately 2 inches from the pouring lip of the skillet.
14. The stainless steel UniVerse Skillet is rapidly cleaned with a mild detergent. Water, waste, and scraps are easily removed into the receiving
pan for disposal. (It is always recommended that this type of unit be presoaked if possible.)
15. Breakfast foods such as sausage, bacon, pancakes, fried eggs, scrambled eggs, and French toast are a few of the more common items that
can be cooked in the UniVerse Skillet.
16. When cooking meat or poultry, all pieces should be of fairly uniform size and weight and should be turned at least once while simmering.
17. This unit can be converted to a proof box by placing a small amount of water in the pan to form steam and then placing the food in another
pan. The thermostat should be set very low (100–150°F).
18. The unit can also be used as a holding cabinet by adding water and setting the thermostat at approximately 175°F.
19. When using water over and over for vegetable cookery, be sure to add water occasionally to keep level at about 3–4 inches. Thermostat
should be set at 250°F.
20. Perforated 2 1/2"-deep pans are suggested for vegetables for the most satisfactory results. The pan can then be removed easily and
transferred to the serving line.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4 TEST KITCHEN BULLETIN
TABLE 4.1
COOKING PORTIONS AND TIMES
UNIVERSE SILLET
ALL MODULAR & TUBULAR LEG MODELS
The UniVerse Skillet is one of the most versatile pieces of equipment to be found in any restaurant or institutional kitchen. It
enables the cook to stew, simmer, pan-fry, braise, grill, or sauté, and all with a very uniform heat pattern. The figures given
below are suggested quantities and temperature settings and estimated numbers of orders per load and per hour. When two
temperatures are given, the first is to start the product, the second to finish the product.
30 GALLON
PER LOAD
40 GALLON
PER LOAD
PORTION
SIZE
THERMOSTAT BATCHES
ITEM
SETTING
PER HOUR
QTY.
YIELD
QTY.
YIELD
BREAKFAST FOODS
Bacon
3 slices
350o
12
2#
10
3#
15
Eggs
Boiled-Hard
Boiled-Soft
Fried
1 egg
1 egg
1 egg
225o
225o
400o
225o
300o
450o
250o
400o
5
8
4
50
50
30
50
50
30
75
75
45
60
75
75
45
60
Poached
1 egg
5
36
36
Scrambled
French Toast
Regular Oatmeal
Pancakes
1 1/2 eggs
3 slices
1/2 cup
2 each
200o
1
7
2
10
18 gallon
35 slices
20#
720
12
500
15
28 gallon 1100
50 slices
40#
17
1000
25
30 each
50 each
FISH
Clams
1 pt.
2-3 oz.
4 oz.
5 oz.
1-1#
400o
400o
400o
450o
350o
450o
10
5
4
3
4
10 qts.
70-3 oz.
60-4 oz.
60-4 oz.
20-1#
20
35
60
60
20
50
15 qts.
110-3 oz.
90-4 oz.
90-4 oz.
30-1#
30
55
90
90
30
75
Fish Cakes
Haddock Filet
Halibut Steak
Lobster
Swordfish
5 oz.
3
50-5 oz.
75-5 oz.
SAUCES, GRAVIES & SOUPS
Brown Gravy
Cream Sauces
Cream Soup
French Onion Soup
Meat Sauce
1 oz.
2 oz.
6 oz.
6 oz.
4 oz.
350o
250o
200o
225o
350o
200o
175o
2
1
1
1
1
18 gallons 2300 35 gallons 4500
18 gallons 1150 35 gallons 2250
18 gallons 375 35 gallons 725
18 gallons 350 35 gallons 700
18 gallons 575 35 gallons 1100
200o
MISCELLANEOUS
Grilled Cheese
Macaroni & Cheese
Rice
1 sand
8 oz.
4 oz.
4 oz.
400o
200o
350o
350o
8
2
1
2
35 sand
35
50 sand
50
18 galllons 300 35 gallons 525
20# raw
8# raw
225o
225o
320
200
40#
12#
650
300
Spaghetti
CONTINUED
4
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4 TEST KITCHEN BULLETIN
PORTION
SIZE
THERMOSTAT
SETTING
BATCHES 30 Gal. PER LOAD 40 Gal. PER LOAD
ITEM
PER HOUR
QTY.
YEILD
QTY.
YEILD
MEAT, POULTRY
Bacon
Beef
American Chop Suey
Beef Stew
Corn Beef Hash
Cheeseburger
Hamburger
Meatballs
3 Slices
350 0
12
2#
10
3#
15
6 oz.
8 oz.
5 oz.
3 oz.
3 oz.
1 oz.
2 oz.
5 oz.
6 oz.
4 oz.
400 0
300 0
400 0
300 0
300 0
400 0
350 0
400 0
400 0
300 0
225 0
2
--
5
12
15
3
--
3
5
18 Gal.
18 Gal.
16#
7#
7#
12 1/2#
120#
16#
350
280
50
35
35
65
500
50
40
100
35 Gal.
35 Gal.
25#
10#
10#
18#
180#
24#
22 1/2#
40#
700
560
75
50
50
100
750
75
60
160
225 0
200 0
Pot Roast
Salisbury Steak
Sirloin Steak
Swiss Steak
Chicken
Pan-Fried
Whole
15#
25#
200 0
200 0
1
2 1/4's
2 oz.
350 0
350 0
3
--
50 Pieces
16-5#
25
200
80 Pieces
24-5#
40
265
Frankfurters
Grilled
Boiled
Ham Steak
Pork Chops
Sausage Links
Turkey
Off Carcass
On Carcass
2 oz.
2 oz.
3 oz.
5 oz.
3 Links
300 0
250 0
400 0
350 0
350 0
8
12
8
4
7
22#
16#
10#
15#
30#
176
128
50
50
120
33#
25#
15#
25#
45#
264
200
75
75
180
2 oz.
2 oz.
400 0
400 0
200 0
200 0
--
--
3-26-30#
4-16-20#
200
175
4-26-30#
6-16-20#
275
265
VEGETABLES
Canned
Freash
Beans
3 oz.
400 0
6
30#
125
45#
200
3 oz.
3 oz.
3 oz.
3 oz.
3 oz.
3 oz.
1 ear
3 oz.
4 oz.
4 oz.
400 0
400 0
400 0
400 0
400 0
250 0
400 0
400 0
225 0
400 0
3
1
3
5
2
5
8
2
10
2
25#
30#
25#
20#
35#
15#
50 ears
40#
6#
20#
125
125
125
80
150
75
50
200
25
50#
60#
40#
30#
70#
25#
75 ears
60#
9#
30#
250
300
200
125
300
125
75
300
35
150
Beets
Broccoli
Cabbage
Carrots
Cauliflower
Corn
Potatoes
Spinach
Turnips
100
Frozen
Beans
3 oz.
3 oz.
3 oz.
3 oz.
3 oz.
3 oz.
3 oz.
3 oz.
3 oz.
400 0
250 0
400 0
250 0
250 0
250 0
250 0
400 0
400 0
6
4
8
6
3
18
7
10
3
15#
15#
12#
15#
15#
15#
15#
15#
15#
60
60
50
60
50
50
50
75
75
22 1/2#
22 1/2#
18#
22 1/2#
22 1/2#
22 1/2#
22 1/2#
22 1/2#
22 1/2#
90
90
75
90
90
90
90
110
110
Lima Beans
Broccoli
Sliced Carrots
Baby Carrots
Corn
Baby Onions
Peas
Spinach
DESSERT ITEMS
Butterscotch Sauce
Cherry Cobbler
Chocolate Sauce
Cornstarch Pudding
Fruit Gelatin
1 oz.
3 oz.
1 oz.
4 oz.
200 0
200 0
200 0
200 0
250 0
1
1
1
1
2
18 Gal.
19 Gal.
20 Gal.
21 Gal.
22 Gal.
2300
750
2300
575
35 Gal.
36 Gal.
37 Gal.
38 Gal.
39 Gal.
4500
1500
4500
1100
1500
3
oz.
750
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5 ILLUSTRATED PARTS LIST
TABLE 5.1 TOP ASSEMBLY
30 & 40
GALLON
QTY.
PART NO.
PART NO.
ITEM
30 GALLON 40 GALLON DESCRIPTION
1
2
3
4
5
6
7
8
9
1
1
1
1
1
1
1
2
1
1
2
4
1
1
1
1
1
1
1
1
1
1
2
2
2
4
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
98-1296
98-1010
98-1031
98-1339
98-1300
98-1357
98-1305
08-7809
98-1311
98-1310
98-1012
91-9325
91-9262
91-9261
98-1454
98-1451
98-1340
98-1341
98-1455
98-1452
98-1068
98-1028
98-1258
98-1212
08-7810
REF
08-7806
98-1402
98-0985
98-1288
10-5520
09-5267
08-7913
REF
10-5052
08-6320
98-1308
91-9144
91-9145
08-7813
98-1216
98-1326
98-1270
98-1333
98-1262
98-1538
98-1295
98-1010
98-1031
98-1339
98-1300
98-1356
98-1024
08-7809
98-1093
98-1090
98-1012
91-9325
91-9262
91-9261
98-1454
98-1451
98-1340
98-1341
98-1455
98-1452
98-1068
98-1028
98-1258
98-1212
08-7810
REF
08-7806
98-1402
98-0985
98-1288
10-5520
09-5267
08-7913
REF
10-5052
08-6320
98-1308
91-9144
91-9145
08-7813
98-1216
98-1326
98-1270
98-1333
98-1262
98-1539
FRAME WELD ASSY.
GEAR BOX
BEARING SUPPORT ASSY.
BEARING MOUNT LEFT
BEARING MOUNT RIGHT
SKILLET PAN ASSY.
SHAFT
SHOULDER SCREW
STIFFENER, PAN COVER
COVER
HINGE
KNOB
ARM, VENT COVER
VENT COVER
ELECTRIC NEMA BOX ASSY., 208/240V MANUAL TILT UNITS
ELECTRIC NEMA BOX ASSY., 208/240V POWER TILT UNITS
ELECTRIC NEMA BOX ASSY., 240/380 V & 220/415V MANUAL TILT UNITS
ELECTRIC NEMA BOX ASSY., 240/380 V & 220/415V POWER TILT UNITS
ELECTRIC NEMA BOX ASSY., 480V MANUAL TILT UNITS
ELECTRIC NEMA BOX ASSY., 480V POWER TILT UNITS
WELD ASSY., CAM LIFT, POWER LIFT UNITS
SHAFT JOINT
ARM, EXTENSION
ARM, LIFT
INSERT 5/16
SHOCK MOUNT, COMES WITH SHOCKS, NO NUMBER
GAS SHOCKS
MOTOR MOUNTING BRACKET, POWER LIFT UNITS
MOTOR, POWER LIFT UNITS
CONTROL BOX
60 MIN. TIMER
10
11
12
13
14
15
15A
15B
15C
15D
15E
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
32A
33
34
35
36
37
38
39
39A
40
TIMER KNOB
THERMOSTAT
THERMOSTAT KNOB, COMES WITH THERMOSTAT, NO NUMBER
LIGHT
POWER SWITCH, POWER LIFT UNITS
POWER SWITCH HOLE PLUG, MANUAL TILT UNITS
LEFT SPRING
RIGHT SPRING
INSERT 3/8
UNIVERSAL, EXTENDED, POWER TILT UNITS
WELD ASSY., CAM, UP AND DOWN
HANDLE BRACKER, MANUAL TILT UNITS
CRANK HANDLE, MANUAL TILT UNITS
CRANK HANDLE, POWER TILT UNITS
WELD ASSY., TILT MECHANISM
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5 ILLUSTRATED PARTS LIST
FIG. 5.1 TOP ASSEMBLY
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5 ILLUSTRATED PARTS LIST
TABLE 5.2 PAN ASSEMBLY
30
40
PART NO.
PART NO.
GALLON GALLON
ITEM
QTY.
QTY.
30 GALLON 40 GALLON DESCRIPTION
1
2
2A
3
4
5
6
7
8
9
1
4
4
5
1
2
1
1
1
1
1
1
4
4
9
1
2
1
1
1
1
1
98-1245
98-1081
98-1083
98-1347
98-1254
98-1221
91-7520
08-6351
98-1255
08-5894
08-6305
98-1224
98-1080
98-1082
98-1347
98-1254
98-1253
91-7520
08-6351
98-1255
08-5894
08-6305
PAN WELD ASSY.
HEATING ELEMENTS, 208V
HEATING ELEMENTS, 240V
U-CHANNEL
COVER, MIDDLE HEATING ELEMENT
COVER, SIDE HEATING ELEMENT
HI LIMIT THERMOSTAT BRACKET
HI LIMIT THERMOSTAT
BRACKET, HEATING ELEMENT CONDUIT
MARKET FORGE NAME PLATE
TEMPERATURE SENSOR
10
FG. 5.2 PAN ASSEMBLY
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5 ILLUSTRATED PARTS LIST
TABLE 5.3 NEMA BOX ASSEMBLY
ITEM
PART NO. DESCRIPTION
QTY.
1
2
2A
3
4
5
6
7
8
9
10
11
12
14
15
15A
98-1336 NEMA BOX, LARGE
1
3
1
1
1
1
1
1*
1
1
1
1
1
2
1
2*
08-7901 MICROSWITCH, POWER TILT UNITS
08-7901 MICROSWITCH, MANUAL TILT UNITS
91-9178 CAPACITOR BRACKET
10-5503 TERMINAL BLOCK BLACK
10-5070 END PIECE, TERMINAL BLOCK, BLACK
10-5220 ELECTRICAL GROUND
10-5944 CONTACTOR
98-1265 MOUNTING PLATE, NEMA BOX
10-6262 TERMINAL BLOCK, WHITE
10-6963 END PIECE, TERMINAL BLOCK, WHITE
10-5234 TRANSFORMER, 250V
REF
CAPACTOR, COMES WITH MOTOR
08-7826 MICROSWITCH HOLE PLUG, MANUAL TILT UNITS
08-7846 BOOT, RUBBER, MICROSWITCH
08-7846 BOOT, RUBBER, MICROSWITCH
* ONLY 208V & 240V UNITS HAVE 2 CONTACTORS; ALL OTHERS HAVE 1.
FIG. 5.3 NEMA BOX ASSEMBL
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6 TROUBLESHOOTING & MAINTENANCE
PROBLEM
PROBABLE CAUSE
REMEDY
PART NO.
1. Uneven Heating. a.
Temperature control out of
calibration or defective.
a. Calibrate or replace.
a. 08-6365
2. Signal Light Out.
3. Unit fails to heat.
a. Burnt out bulb.
b. BrokenTemperature control.
c. Loose electrical connection.
a. Replace.
b. Replace.
c. Repair
a. 10-5052
b. 08-6365
a. Circuit breaker is off.
b. Malfunction of interlock switch
c. Broken Ignition module
d. Broken ignitor
a. Reset circuit breaker
b. Adjust or replace.
c. Replace.
d. Replace.
e. Replace.
b. 09-6465
c. 08-71 10
d. 10-8259
e. 08-6452
10-4758
e. Broken flame sensor
4. No 110 Volts output.
5. No gas to unit.
a. Defective temperature control.
b. Broken temperature sensor
a. Replace.
b. Replace.
a. 08-6365
b. 08-6305
a. Defective gas valve.
a. Replace.
a. 10-7686
10-7683
08-7108
09- 1150
09- 1151
CALIBRATION OF TEMPERATURE CONTROL
1. Ensure that pan is empty and clean before calibrating.
2. Place a surface thermometer on left or right rear sides, 3" from sides of griddle surface.
NOTE: Check that magnets on thermometer extend through holes in circular base plate and are in complete contact with
griddle surface.
Temperature Control Circut Board
3. Set temperature control knob at 375°F (191°C).
4. Allow skillet to preheat and stabilize 2–3 cyc
5. Record thermometer reading. If a temperature of 370°–380°F (188°–
193°C) is recorded, procedure is complete. If not, go on to step 6.
6. Remove control box cover by removing screw in rear and right side of cover.
7. Locate temperature control circuit board (see Figure 6.1) and calibrate as follows:
a. If temperature goes above 375
°F (191°C), turn setpot labeled HI
°F (191°C), turn setpot labeled HI
counterclockwise to decrease temperature.
b. If temperature goes below 375
clockwise to increase temperature.
FIG. 6-1
NOTE: Turn the HI setpot only. Be careful when turning setpot—just a slight turn (approximately 22°) will change
temperature by 25°F.
8. Allow skillet to cycle three (3) times. This cycling allows temperature control to stabilize.
9. Record thermometer reading when pilot light goes out. If a temperature of 370°–380°F (188°–193°C) is recorded,
calibration procedure is complete. If not, repeat steps 7 and 8 until appropriate temperature is recorded.
10. Replace control box cover by pushing down and replacing screw in rear and right side of cover.
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6 TROUBLESHOOTING & MAINTENANCE
REPLACEMENT OF TEMPERATURE CONTROL
1. Place circuit breaker in off position.
2. Remove skirted dial knob by pulling it off the control box cover.
3. Remove control box cover by removing screw in rear and right side of cover.
4. Disconnect all wire leads from temperature control.
NOTE: Leads should be marked appropriately to facilitate re-installation.
5. Remove temperature control by removing two (2) pan head nuts from side of control box.
6. Install new temperature control and reverse steps 1–5.
ADJUSTMENT OF INTERLOCK SWITCH
1. Tilt skillet pan all the way in the downright position.
NOTE: If adjusting the interlock switches for the tilt mechanism in a power tilt unit, the pan will have to be all the way in the
upright position to adjust one of the switches.
2. Place circuit breaker in off position.
3. Open the nema box by loosening the two screws at the top of the nema box.
4. Loosen the bottom nut of the switch until it contacts with the cam and depresses the plunger on the switch.
6. Close and fasten the nema box by tightening the 2 screws at the top of the box.
7. Place circuit breaker in on position. 5. Tighten the top nut on the switch to keep the switch in the desired location.
REPLACEMENT OF ELECTRICAL ELEMENTS
TABLE 6.2 HEATER ELEMENTS
[ELECTRIC]
1. Tilt skillet pan upright by turning handwheel clockwise.
VOLTAGE
PART NO.
2. Remove bottom cover and both heat shields. When bottom
cover is removed, terminals are exsposed. Remove wiring.
208V
98-1080 (40-GALLON)
98-1081 (30-GALLON)
3. Remove bottom clamp plates to expose elements by
removing nuts and lockwashers on studs.
240V
480V
240/415V
98-1082 (40-GALLON)
98-1083 (30-GALLON)
4. Remove spacers between elements and mark their location.
5. Replace defective elements and reverse the procedure.
CLEANING
1. The skillet should be cleaned daily.
2. Wash the skillet with a mild detergent and hot water. If food is stuck to the surface of the skillet pan, soak it and use a little
heat to loosen the food. Then, wash with clear water and dry.
3. Be sure to wash under the skillet cover and rinse with clear water.
4. Check the skillet pouring lip corners to be sure they are clean. Also, wash around the exterior of the skillet. Rinse with clear
water and air dry.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
TABLE 7.1 SINGLE PANTRY FAUCET
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
98-1199 CONTROL BOX, REAR, PANTRY FAUCET
98-1360 MOUNTING PLATE, SINGLE PANTRY FAUCET
98-1366 SINGLE PANTRY FAUCET
98-1368 ADAPTER, SINGLE PANTRY FAUCET
10-5753 SPRAY NOZZLE WITH SWIVEL NOZZLE
10-3767 NIPPLE, FILL FAUCET RISER, 6"
1
1
1
2
1
1
8
1
1
1
1
2
1
REF
#8-32 WELDNUT
98-1475 TUBING, BRAIDED TEFLON
98-1477 COUPLER, BRASS HOSE BARB, 3/8 ID TO 3/8 PIPE
98-0877 ASSY., WATER LINE INLET
10-1761 #8-32 SCREW, 3/8 LG., S.S.
08-1206 HOSE CLAMP
98-1479 COUPLER, BRESS HOSE BARB, 3/8 ID X 1/2" THD. FEMALE
7
11 4X
2
6
5
4
1
13.00 (REF)
8
13
3
A
9
10
A
FIG. 7.1 SINGLE PANTRY FAUCET
DETAIL A-A
BACK VIEW
12
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
TABLE 7.2 DOUBLE PANTRY FAUCET
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
98-1199 CONTROL BOX, REAR, PANTRY FAUCET
98-1362 MOUNTING PLATE, DOUBLE PANTRY FAUCET
98-1367 DOUBLE PANTRY FAUCET
1
1
1
8
1
2
1
1
5
1
6
1
1
6
REF
#8-32 WELDNUT
98-1475 TUBING, BRAIDED TEFLON, 3/8 ID X 5/8 OD X 10.5 LG.
98-1474 TUBING, BRAIDED TEFLON, 3/8 ID X 5/8 OD X 15 LG.
10-5753 SPRAY NOZZLE WITH SWIVEL BODY
10-3767 NIPPLE, FILL FAUCET RISER, 6"
98-1477 #8-32 WELDNUT
98-0877 COUPLER, BRASS HOSE BARB, 3/8 ID TO 3/8 PIPE
10-1761 ASSY., WATER LINE INLET
10-3108 #8-32 SCREW, 3/8 LG., S.S.
98-1479 COUPLER, BRESS HOSE BARB, 3/8 ID X 1/2" THD. FEMALE
08-1206 HOSE CLAMP
4
2
11
1
13
12
3
7
8
9
5
6
A
9
10
A
14
(6 PLCS)
FIG. 7.2 DOUBLE PANTRY FAUCET
DETAIL A-A
BACK VIEW
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
TABLE 7.3 SINGLE SPRAY HOSE
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
98-1199 CONTROL BOX, REAR, PANTRY FAUCET
98-1360 MOUNTING PLATE, SINGLE PANTRY FAUCET
98-1366 SINGLE PANTRY FAUCET
98-1368 ADAPTER, SINGLE PANTRY FAUCET
98-1477 COUPLER, BRESS HOSE BARB, 3/8 ID X 3/8 THD. MALE
98-1401 CHECK VALVE, 1/2 X 1/2 IPS
1
1
1
2
1
1
6
1
2
1
4
1
2
REF
#8-32 WELDNUT
98-1475 TUBING, BRAIDED TEFLON
08-4892 COUPLER, BRASS HOSE BARB, 3/8 ID TO 3/8 PIPE
98-0877 ASSY., WATER LINE INLET
10-1761 #8-32 SCREW, 3/8 LG., S.S.
10-0959 SPRAY HOSE ASSY.
08-1206 HOSE CLAMP
7
11 4X
13
2
4
1
8
5
6
3
A
9
10
A
DETAIL A-A
BACK VIEW
FIG. 7.3 SINGLE SPRAY HOSE
14
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
TABLE 7.4 DOUBLE SPRAY HOSE
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
98-1199 CONTROL BOX, REAR, PANTRY FAUCET
98-1362 MOUNTING PLATE, DOUBLE PANTRY FAUCET
98-1367 DOUBLE PANTRY FAUCET
1
1
1
8
1
2
1
1
5
1
1
1
1
6
REF
#8-32 WELDNUT
98-1475 TUBING, BRAIDED TEFLON, 3/8 ID X 5/8 OD X 10.5 LG.
98-1474 TUBING, BRAIDED TEFLON, 3/8 ID X 5/8 OD X 15 LG.
08-4892 OUPLER, BRESS HOSE BARB, 3/8 ID TO 1/2" THD. MALE
98-1401 CHECK VALVE
98-1477 COUPLER, BRASS HOSE BARB, 3/8 ID MALE PIPE 3/8
98-0877 WATER LINE INLET ASSY.
10-1761 #8-32 SCREW, 3/8 LG., S.S.
10-3108 REMOTE VALVE
98-0959 SPRAY HOSE ASSY.
08-1206 HOSE CLAMP
FIG. 7.4 DOUBLE SPRAY HOSE
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
TABLE 7.5 PAN SUPPORT
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
98-1186 PAN SUPPORT WELD ASSY.
08-7838 JAM NUT, 1/4-20
98-1378 PIVOT ARM
98-1188 FRAME BRACKET
10-1814 BOLT, 1/4-20 X 3/4 S.S.
98-1416 PIVOT STUD
08-7837 BELLVILLE SPRING WASHER S.S.
98-1417 LOWER ARM
98-1419 UPPER ARM
1
6
2
1
4
4
4
1
1
1
1
10
11
98-1415 GUARD
10-1788 SCREW, 10-32 X 3/8 LG.
FIG. 7.5 PAN SUPPORT
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
OPTIONAL CASTERS WITH GAS STRAIN RELIEF
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
4
5
98-1421 GAS STRAIN RELIEF KIT FOR CASTER UNITS
98-1523 CASTER WITH BRAKE
98-1191 CASTER WITHOUT BRAKE
08-7839 EYE-BOLT, 1/4-20 X 2" LG.
1
2
2
1
1
S-4839
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FOR CASTERS ON THE UNIVERSE SKILLET
FORM NUMBER: S-4839
WARNING: Before raising skillet base make sure the pan is in the down position for steps 1-8.
1. Raise the front of the skillet base and brace with front of skillet off the ground.
2. Insert casters with brakes into the front legs of the frame
NOTE: Casters must screw fully into the frame of the skillet in order for them to be able to be tightened.
3. Tighten the nut at the base of the casters until casters are securely fastened into the legs of the frame.
4. Put the universe skillet down on the floor.
5. Apply the brakes in the front by stepping on the lever on the side of the front casters until it is in the on position.
6. Raise the rear of the skillet base and brace with rear of skillet off the ground.
7. Insert casters without brakes into the rear legs of the frame
NOTE: Casters must screw fully into the frame of the skillet in order for them to be able to be tightened.
8. Tighten the nut at the base of the casters until casters are securely fastened into the legs of the frame.
9. Put the Universe Skillet down on the floor.
NOTE: For units with Gas Strain Relief Kit (MF# 98-1421) refer to # 10.
10. Refer to the Installation Instruction provided with the Gas Strain Relief Kit (MF #98-1421) for recommended
mounting instructions for the complete Gas Strain Relief Quick-Disconnect kit.
NOTE: See figure for recommended location of I-bolt (see below). (MF #08-7839).
7-6
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
MODULAR OPTIONS
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
98-1434 ASSY., MODULAR PANEL, LEFT SIDE
98-1498 WELD ASSY., COVER, LEFT SIDE
98-1431 ASSY., MODULAR PANEL, FRONT, 30 GALLON
98-1432 ASSY., MODULAR PANEL, FRONT, 40 GALLON
98-1524 PANEL, REAR MODULAR, 30 GALLON
98-1525 PANEL, REAR MODULAR, 40 GALLON
98-1469 COVER, MODULAR FRAME, FRONT HORIZONTAL, 30 GAL.
98-1468 COVER, MODULAR FRAME, FRONT HORIZONTAL, 40 GAL.
1
1
1
1
1
1
1
1
MODULAR INSTRUCTIONS:
1. After receiving Universe Skillet and uncrating unit, make sure all components needed for modularity have been shipped
with the unit. (See below for needed components for 30 -Gal or 40-Gal unit)
2. Position Modular Support Bar (Item 1, 30-Gal , Item 2, 40-Gal) by locating holes on Support Bar in line with mounting
holes on the bottom of front legs. Secure in place by screwing adjustable legs (Item 4) and Washer (Item 3) into holes on
bottom of front legs. Tighten securely. (See Fig 7.6)
FIG. 7.6 MODULAR SUPPORT BAR
TABLE FOR FIG. 7.6
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
4
98-1435 MODULAR SUPPORT BAR, 30 GALLON
98-1436 MODULAR SUPPORT BAR, 40 GALLON
08-7836 WASHER, S.S. 1.63" OD X 0.56 ID
98-1521 LEG, ADJUSTABLE, 1.63" OD, S.S.
1
1
2
2
3. Mount Flanged Adjustable Feet (Item 1) and Washer (Item 2) on bottom of rear legs. Tighten securely. (See Fig 7.7)
4. Mount Modular Panel Assembly, Left Side (Item 1) by pushing panel
into mounting holes located on left side vertical frame supports. Ball
FIG. 7.7 ADJUSTABLE LEG
plungers should line up with mounting holes, and allow easy on/off
access. (See Fig 7.8)
5. Mount Modular Panel Assembly, Front (Item 3 (30-Gal), Item 4 (40-
Gal)) by pushing panel into mounting holes located on front vertical
frame supports. Ball plungers should line up with mounting holes, and
allow easy on/off access. (See Fig 7.8)
OPTIONAL: MODULAR LINE ACCESORIES
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
6. Mount Cover Assy (Item 2) with Trim Kit Market Forge Part No . 98-1517
7. Mount Rear Modular Panel (Item 5 (30-Gal), Item 6 (40-Gal)) with 6 #10-32 Machine Screws to tapped holes on rear
vertical frame support bars.
FIG. 7.8 MODULAR STAND
TABLE FOR FIG. 7.8
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
98-1434 ASSY., MODULAR PANEL, LEFT SIDE
98-1498 WELD ASSY., COVER, LEFT SIDE
98-1431 ASSY., MODULAR PANEL, FRONT, 30 GALLON
98-1432 ASSY., MODULAR PANEL, FRONT, 40 GALLON
98-1524 PANEL, REAR MODULAR, 30 GALLON
98-1525 PANEL, REAR MODULAR, 40 GALLON
98-1469 COVER, MODULAR FRAME, FRONT HORIZONTAL, 30 GAL.
98-1468 COVER, MODULAR FRAME, FRONT HORIZONTAL, 40 GAL.
1
1
1
1
1
1
1
1
(FACTORY INSTALLED)
(FACTORY INSTALLED)
TRIM JOINTING KIT OPTIONS
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
98-0969 3/8-16 THREADED ROD X 3.875" LG.
10-2317 3/8-16, HEX NUT, S.S.
10-2405 5/16 WASHER, S.S.
98-1190 L-STRIP, MODULAR, UNI. SKILLET
98-1518 T-STRIP, MODULAR, UNI. SKILLET
8
26
26
1
1
1
S-2417
INSTALLATION INSTRUCTIONS, MODULAR KIT
98-1464 SPACER
98-1498 WELD ASSY., COVER, LEFT SIDE
1
1
7-8
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
TRIM JOINTING KIT INSTALLATION INSTRUCTIONS
FORM NUMBER: S-2417
1. Thread Item 1 (Refer to Drawing 98-1517) 3/8-16 Threaded Bolt thru Riv-nut on the lower left side of the skillet
so that there is enough room to secure Washer (Item 3)and Nut (Item 2) on the inside of the skillet. Refer to
figure 1.2. Secure Threaded Bolt (Item 1)into place using Washer (Item 3) and Nut (Item 2) hand tighten
washer and nut into place. Repeat this procedure for all upper mounting holes. (4 places)
2. Use additional Washers (Item 2) and Nuts (Item 3) provided with kit to adjust and use as spacers where
needed during assembly.
3. If feasible at this time align skillet with adjoining unit. Threaded Bolt (Item 1) should slide thru mounting
location provided on allGF Market Forge modular assembly frames. Attach using Washers (Item 3) and Nuts
(Item 2) to inside of adjoining unit. Hand tighten washer and nut into place. Repeat this procedure for all lower
mounting holes. (4 places) (See Fig 7.9)
TABLE FOR FIG. 7.9
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
98-0969 3/8-16 THREADED ROD
10-2317 3/8-16 HEX NUT
10-2401 3/8 WASHER
4
13
13
FIG. 7.9 CROSS SECTION
4. After all eight Threaded Rods (Item 1) have been hand tightened, reinstall all modular frame enchancements
provided with the Universe Skillet.
5. Tighten and secure all nuts.
6. Refer to Installation & Operating Instructions before using unit.
7. Mount Frame Cover (Item #`1) to left side of frame positioning slots over 3/8-16 Threaded Rod. Do Not tighten
threaded rod at this time. (See Fig 7.10)
8. Mount Spacer, Modular Frame (Item #2) by securing to adjoining unit with #10-32 Self Tapping Screw or Nut
and bolt as required. Mounting holes are found on adjoining frame base. Fits both left and right side opening
doors. (See Fig 7.10)
9. Tighten and secure all nuts.
10. Refer to Installation & Operating Instructions before using unit.
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
FIG. 7.10 JOINTING KIT STAND
TABLE FOR FIG. 7.11
ITEM
PART NO. DESCRIPTION
QTY.
1
2
3
08-7903 SPRING, SPRAY HOSE, GOOSENECK
08-7904 SPRING BODY, SPRAY HOSE (ADAPTER)
08-7905 RISER, 3" CHROME PLATED, 3/8 THD.
1
1
1
FIG. 7.11 SPRING SUPPORT FOR SPRAY HOSE
7-10
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 OPTIONS PARTS LIST
TABLE FOR FIG. 7.12
ITEM
30
40
PART NO. DESCRIPTION
QTY. QTY.
1
1
2
3
4
98-1231 PAN, 30 GALLON, UNI. SKILLET
98-1036 PAN, 40 GALLON, UNI. SKILLET
98-1398 DRAW OFF TUBE
1
1
1
1
1
10-4928 DRAW OFF VALVE
FIG. 7.12 TANGENT DRAW-OFF
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
|