Makita Saw 5007NBA User Manual

Circular Saw  
Equipped with Electric Blade Brake  
185 mm (7-1/4”)  
MODEL 5007NBA  
DOUBLE  
INSULATION  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
w w w. m a k i t a t o o l s . c o m  
Download from Www.Somanuals.com. All Manuals Search And Download.  
change the plug in any way. Double insula-  
tion eliminates the need for the three wire  
balance enables better control of the tool in  
unexpected situations.  
grounded power cord and grounded power  
supply system.  
14. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions. Ordinary  
eye or sun glasses are NOT eye protection.  
5. Avoid body contact with grounded sur-  
faces such as pipes, radiators, ranges and  
refrigerators. There is an increased risk of  
electric shock if your body is grounded.  
Tool Use and Care  
6. Do not expose power tools to rain or wet  
conditions. Water entering a power tool will  
increase the risk of electric shock.  
15. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
7. Do not abuse the cord. Never use the cord  
to carry the tools or pull the plug from an  
outlet. Keep cord away from heat, oil,  
sharp edges or moving parts. Replace  
damaged cords immediately. Damaged  
cords increase the risk of electric shock.  
16. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
8. When operating a power tool outside, use  
an outdoor extension cord marked “W-A”  
or “W”. These cords are rated for outdoor  
use and reduce the risk of electric shock.  
17. Do not use tool if switch does not turn it  
on or off. Any tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
18. Disconnect the plug from the power  
source before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
9. Stay alert, watch what you are doing and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
19. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
10. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or long  
hair can be caught in moving parts.  
20. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edges are less likely  
to bind and are easier to control.  
21. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tools  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
11. Avoid accidental starting. Be sure switch  
is off before plugging in. Carrying tools with  
your finger on the switch or plugging in tools  
that have the switch on invites accidents.  
12. Remove adjusting keys or wrenches  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
22. Use only accessories that are recom-  
mended by the manufacturer for your  
model. Accessories that may be suitable for  
one tool, may become hazardous when used  
on another tool.  
13. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
24. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
electric shock or injury.  
SERVICE  
23. Tool service must be performed only by  
qualified repair personnel. Service or main-  
tenance performed by unqualified personnel  
could result in a risk of injury.  
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.  
When using an extension cord, be sure to use one heavy enough to carry the current your  
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of  
power and overheating. Table 1 shows the correct size to use depending on cord length and  
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-  
ber, the heavier the cord.  
Table 1: Minimum gage for cord  
Volts  
120 V  
Total length of cord in feet  
Ampere Rating  
25 ft.  
50 ft.  
100 ft.  
150 ft.  
More Than  
Not More Than  
AWG  
0
6
10  
12  
6
18  
18  
16  
14  
16  
16  
16  
12  
16  
14  
14  
14  
12  
12  
10  
12  
16  
Not Recommended  
SPECIFIC SAFETY RULES  
USB008-5  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to circular saw safety  
rules. If you use this tool unsafely or incorrectly, you can suffer  
serious personal injury.  
1. DANGER! Keep hands away from cutting  
area and blade. Keep your second hand  
on auxiliary handle, or motor housing. If  
both hands are holding the saw, they cannot  
be cut by the blade.  
CAUTION: Blades coast after turn off. Wait  
until blade stops before grasping cut material.  
2. Check lower guard for proper closing  
before each use. Do not operate saw if  
lower guard does not move freely and  
close instantly. Never clamp or tie the  
lower guard into the open position. If saw  
is accidentally dropped, lower guard may be  
bent. Raise the lower guard with the Retract-  
ing Lever and make sure it moves freely and  
does not touch the blade or any other part, in  
all angles and depths of cut.  
Keep your body positioned to either side  
of the saw blade, but not in line with the  
saw blade. KICKBACK could cause the saw  
to jump backwards. (See Causes and Oper-  
ator Prevention of Kickback)  
Do not reach underneath the work. The  
guard can not protect you from the blade  
below the work. Do not attempt to remove cut  
material when blade is moving.  
To check lower guard, open lower guard by  
hand, then release and watch guard closure.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Also check to see that Retracting Lever does  
not touch tool housing. Leaving blade  
exposed is VERY DANGEROUS and can  
lead to serious personal injury.  
10. Never use damaged or incorrect blade  
washers or bolts. The blade washers and  
bolt were specially designed for your saw, for  
optimum performance and safety of opera-  
tion.  
3. Check the operation and condition of the  
lower guard spring. If the guard and the  
spring are not operating properly, they  
must be serviced before use. Lower guard  
may operate sluggishly due to damaged  
parts, gummy deposits, or a buildup of debris.  
11. Causes and Operator Prevention of Kick-  
back:  
Kickback is a sudden reaction to a pinched,  
bound or misaligned saw blade, causing an  
uncontrolled saw to lift up and out of the  
workpiece toward the operator.  
When the blade is pinched or bound tightly by  
the kerf closing down, the blade stalls and the  
motor reaction drives the unit rapidly back  
toward the operator.  
If the blade becomes twisted or misaligned in  
the cut, the teeth at the back edge of the  
blade can dig into the top surface of the wood  
causing the blade to climb out of the kerf and  
jump back toward operator.  
Kickback is the result of tool misuse and/or  
incorrect operating procedures or conditions  
and can be avoided by taking proper precau-  
tions as given below:  
Maintain a firm grip with both hands on  
the saw and position your body and arm  
to allow you to resist KICKBACK forces.  
KICKBACK forces can be controlled by the  
operator, if proper precautions are taken.  
When blade is binding, or when interrupt-  
ing a cut for any reason, release the trig-  
ger and hold the saw motionless in the  
material until the blade comes to a com-  
plete stop. Never attempt to remove the  
saw from the work or pull the saw back-  
ward while the blade is in motion or KICK-  
BACK may occur. Investigate and take  
corrective actions to eliminate the cause of  
blade binding.  
4. Lower guard should be retracted manually  
only for special cuts such as “Pocket  
Cuts” and “Compound Cuts.Raise lower  
guard by Retracting Lever. As soon as  
blade enters the material, lower guard  
must be released. For all other sawing, the  
lower guard should operate automatically.  
5. Always observe that the lower guard is  
covering the blade before placing saw  
down on bench or floor. An unprotected,  
coasting blade will cause the saw to walk  
backwards, cutting whatever is in its path. Be  
aware of the time it takes for the blade to stop  
after switch is released.  
6. NEVER hold piece being cut in your hands  
or across your leg. It is important to support  
the work properly to minimize body exposure,  
blade binding, or loss of control.  
7. Hold tool by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring or  
its own cord. Contact with a livewire will  
also make exposed metal parts of the tool  
liveand shock the operator.  
8. When ripping always use a rip fence or  
straight edge guide. This improves the  
accuracy of cut and reduces the chance for  
blade binding.  
When restarting a saw in the workpiece,  
center the saw blade in the kerf and check  
that saw teeth are not engaged into the  
material. If saw blade is binding, it may walk  
up or KICKBACK from the workpiece as the  
saw is restarted.  
9. Always use blades with correct size and  
shape (diamond vs. round) arbor holes.  
Blades that do not match the mounting hard-  
ware of the saw will run eccentrically, causing  
loss of control.  
Support large panels to minimize the risk  
of blade pinching and KICKBACK. Large  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
panels tend to sag under their own weight.  
Supports must be placed under the panel on  
both sides, near the line of cut and near the  
edge of the panel as shown in Fig. 1.  
To minimize the risk of blade pinching and  
kickback. When cutting operation requires  
the resting of the saw on the workpiece, the  
saw should be rested on the larger portion  
and the smaller piece cut off.  
areas. The protruding blade may cut objects  
that can cause KICKBACK. For pocket cuts,  
retract lower guard using Retracting Lever.  
ALWAYS hold the tool firmly with both  
hands. NEVER place your hand or fingers  
behind the saw. If kickback occurs, the saw  
could easily jump backwards over your hand,  
leading to serious personal injury.  
Fig. 3  
Fig. 1 To avoid kickback, do support board or  
Never force the saw. Forcing the saw can  
cause uneven cuts, loss of accuracy, and  
possible kickback. Push the saw forward at  
a speed so that the blade cuts without slow-  
ing.  
panel near the cut.  
12. Use extra caution when cutting damp  
wood, pressure treated lumber, or wood  
containing knots. Adjust speed of cut to  
maintain smooth advancement of tool without  
decrease in blade speed.  
Fig. 2 Do not support board or panel away  
13. Adjustments. Before cutting be sure  
depth and bevel adjustments are tight.  
from the cut.  
Do not use dull or damaged blade.  
Unsharpened or improperly set blades pro-  
duce narrow kerf causing excessive friction,  
blade binding and KICKBACK. Keep blade  
sharp and clean. Gum and wood pitch hard-  
ened on blades slows saw and increases  
potential for kickback. Keep blade clean by  
first removing it from tool, then cleaning it  
with gum and pitch remover, hot water or ker-  
osene. Never use gasoline.  
Blade depth and bevel adjusting locking  
levers must be tight and secure before  
making cut. If blade adjustment shifts while  
cutting, it may cause binding and KICKBACK.  
Use extra caution when making a “Pocket  
Cut” into existing walls or other blind  
14. Avoid Cutting Nails. Inspect for and  
remove all nails from lumber before cut-  
ting.  
15. When operating the saw, keep the cord  
away from the cutting area and position it  
so that it will not be caught on the work-  
piece during the cutting operation. The  
tool is provided with a front grip and rear  
handle for two hand operation. Operate  
with proper hand support, proper work-  
piece support, and supply cord routing  
away from the work area.  
WARNING: It is important to support the  
workpiece properly and to hold the saw  
firmly to prevent loss of control which  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
could cause personal injury. Fig. 4 illus-  
trates typical hand support of the saw.  
Fig. 6  
17. Never attempt to saw with the circular saw  
Fig. 4 A typical illustration of proper hand  
support, workpiece support, and supply  
cord routing.  
held upside down in  
a
vise. This is  
extremely dangerous and can lead to seri-  
ous accidents.  
16. Place the wider portion of the saw base on  
that part of the workpiece which is solidly  
supported, not on the section that will fall  
off when the cut is made. As examples,  
Fig. 5 illustrates the RIGHT way to cut off  
the end of a board, and Fig. 6 the WRONG  
way. If the workpiece is short or small,  
clamp it down. DO NOT TRY TO HOLD  
SHORT PIECES BY HAND!  
Fig. 7  
18. WARNING: Blade coasts to stop after  
switch is released. Contact with coasting  
blade can cause serious injury. Before  
setting the tool down after completing a  
cut, be sure that the lower (telescoping)  
guard has closed and the blade has come  
to a complete stop.  
19. Some material contains chemicals which  
may be toxic. Take caution to prevent dust  
inhalation and skin contact. Follow mate-  
rial supplier safety data.  
Fig. 5  
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before adjusting or checking function on the  
tool.  
001339  
Adjusting depth of cut  
CAUTION:  
1
After adjusting the depth of cut, always tighten the lever  
securely.  
2
Loosen the lever on the depth guide and move the base up  
or down. At the desired depth of cut, secure the base by  
tightening the lever.  
1. Depth guide  
2. Lever  
For cleaner, safer cuts, set cut depth so that no more than  
one blade tooth projects below workpiece. Using proper cut  
depth helps to reduce potential for dangerous KICKBACKS  
which can cause personal injury.  
001357  
Bevel cutting  
Loosen the clamping screw on the bevel scale plate on the  
front of the base. Set for the desired angle (0° - 45°) by tilting  
accordingly, then tighten the clamping screw securely.  
1
2
1. Bevel scale plate  
2. Clamping screw  
001374  
Sighting  
B
A
For straight cuts, align the A position on the front of the base  
with your cutting line. For 45° bevel cuts, align the B position  
with it.  
1
1. Base  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
001396  
Switch action  
CAUTION:  
1
Before plugging in the tool, always check to see that the  
switch trigger actuates properly and returns to the OFF”  
position when released.  
To start the tool, simply pull the switch trigger. Release the  
switch trigger to stop.  
1. Switch trigger  
Electric brake  
This tool is equipped with an electric blade brake. If the tool  
consistently fails to quickly stop blade after switch trigger  
release, have tool serviced at a Makita service center.  
The blade brake system is not a substitute for lower guard.  
NEVER USE TOOL WITHOUT A FUNCTIONING LOWER  
GUARD. SERIOUS PERSONAL INJURY CAN RESULT.  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before carrying out any work on the tool.  
001417  
Removing or installing saw blade  
CAUTION:  
1
Be sure the blade is installed with teeth pointing up at  
the front of the tool.  
Use only the Makita wrench to install or remove the  
blade.  
2
1. Wrench  
To remove the blade, press the shaft lock so that the blade  
cannot revolve and use the wrench to loosen the hex bolt  
counterclockwise. Then remove the hex bolt, outer flange  
and blade.  
2. Shaft lock  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
001434  
To install the blade, follow the removal procedure in reverse.  
BE SURE TO TIGHTEN THE HEX BOLT CLOCKWISE  
SECURELY.  
1
When changing blade, make sure to also clean upper and  
lower blade guards of accumulated sawdust. Such efforts do  
not, however, replace the need to check lower guard opera-  
tion before each use.  
4
2
3
1. Saw blade  
2. Hex bolt  
3. Outer flange  
4. Inner flange  
OPERATION  
CAUTION:  
Be sure to move the tool forward in a straight line gently.  
Forcing or twisting the tool will result in overheating the  
motor and dangerous kickback, possibly causing severe  
injury.  
001460  
Hold the tool firmly. The tool is provided with both a front grip  
and rear handle. Use both to best grasp the tool. If both  
hands are holding saw, they cannot be cut by the blade. Set  
the base on the workpiece to be cut without the blade making  
any contact. Then turn the tool on and wait until the blade  
attains full speed. Now simply move the tool forward over the  
workpiece surface, keeping it flat and advancing smoothly  
until the sawing is completed.  
1
2
3
1. Rear handle  
2. Front grip  
3. Base  
To get clean cuts, keep your sawing line straight and your  
speed of advance uniform. If the cut fails to properly follow  
your intended cut line, do not attempt to turn or force the tool  
back to the cut line. Doing so may bind the blade and lead to  
dangerous kickback and possible serious injury. Release  
switch, wait for blade to stop and then withdraw tool. Realign  
tool on new cut line, and start cut again. Attempt to avoid  
positioning which exposes operator to chips and wood dust  
being ejected from saw. Use eye protection to help avoid  
injury.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
001480  
Rip fence (Guide rule)  
The handy rip fence allows you to do extra-accurate straight  
cuts. Simply slide the rip fence up snugly against the side of  
the workpiece and secure it in position with the screw on the  
front of the base. It also makes repeated cuts of uniform  
width possible.  
1
1. Rip fence (Guide rule)  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before attempting to perform inspection or  
maintenance.  
001496  
Adjusting for accuracy of 90° cut (vertical cut)  
2
1
This adjustment has been made at the factory. But if it is off,  
adjust the adjusting screw with a hex wrench while squaring  
the blade with the base using a triangular rule, try square,  
etc.  
1. Adjusting screw  
2. Base  
001505  
1
1. Triangular rule  
001145  
Replacing carbon brushes  
Remove and check the carbon brushes regularly. Replace  
when they wear down to the limit mark. Keep the carbon  
brushes clean and free to slip in the holders. Both carbon  
brushes should be replaced at the same time. Use only iden-  
tical carbon brushes.  
1
1. Limit mark  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
001515  
Use a screwdriver to remove the brush holder caps. Take out  
the worn carbon brushes, insert the new ones and secure  
the brush holder caps.  
After replacing brushes, plug in the tool and break in brushes  
by running tool with no load for about 10 minutes. Then  
check the tool while running and electric brake operation  
when releasing the switch trigger. If electric brake is not  
working well, ask your local Makita service center for repair.  
1
2
1. Brush holder cap  
2. Screwdriver  
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory  
or attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
Steel & Carbide-tipped saw blades  
Combination  
General purpose blade for fast and smooth rip,  
crosscuts and miters.  
Pressure treated/ Designed for fast cutting of pressure treated  
Wet lumber  
and wet lumber.  
Fine cross cuts  
For sand-free cuts cleanly against the grain.  
Rip fence (Guide rule)  
Wrench 13  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Class  
Postage  
Required  
Post Office will  
not deliver  
without proper  
postage.  
Makita U.S.A., Inc.  
14930 Northam Street  
La Mirada, CA 90638-5753  
Fold  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAIL THIS PORTION  
Your answers to the following questions are appreciated.  
1.This product was purchased from:  
3. How did you learn about this product:  
Home Center  
Other (  
)
Magazine  
Radio  
Hardware/Lumber Store  
Tool Distributor  
From Dealer  
Newspaper  
Store Display  
Catalog  
Exhibition  
From Friend  
Previous Usage  
Other (  
Industrial Supply  
Construction Supply  
)
2. Use of the product is intended for:  
4. Most favored points are:  
Construction Trade  
Industrial Maintenance  
Home Maintenance  
Hobby  
Design  
Repair Service  
Durability  
Power  
Features  
Size  
Price  
Other (  
)
Other (  
)
Makita Brand  
5. Any comments:  
DATE PURCHASED  
MONTH  
MODEL NO.  
DAY  
YEAR  
SERIAL NO.  
STATUS  
SEX  
Married Single  
M
F
INTL.  
LAST NAME / COMPANY NAME  
STREET ADRESS  
CITY  
AREA  
CODE  
STATE  
ZIP CODE  
PHONE  
40-49  
Under 19  
20-29  
30-39  
50-60  
Over 60  
AGE:  
BE SURE TO COMPLETE THE CUSTOMERS PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.  
Please return this portion by facsimile or mail.  
Facsimile No: (714) 522-8133  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
FACTORY SERVICE CENTERS  
1-800-4-MAKITA  
RETAIN THIS PORTION FOR YOUR RECORDS  
ARIZONA  
FLORIDA  
MISSOURI  
PENNSYLVANIA  
1704 Babcock Blvd.  
Pittsburgh, PA 15209  
(412) 822-7370  
3707 E. Broadway Rd., Ste. 6  
Phoenix, AZ 85040  
(602) 437-2850  
750 East Sample Road  
Pompano Beach, FL 33064  
(954) 781-6333  
9876 Watson Road  
St. Louis, MO 63126-2221  
(314) 909-9889  
CALIFORNIA  
GEORGIA  
NEBRASKA  
PUERTO RICO  
41850 Christy St.  
Fremont, CA 94538-5107  
(510) 657-9881  
4680 River Green Parkway NW  
Duluth, GA 30096  
(770) 476-8911  
4129 S. 84th St.  
Omaha, NE 68127  
(402) 597-2925  
200 Guayama St.  
Hato Rey, PR 00917  
(787) 250-8776  
14930 Northam St.  
La Mirada, CA 90638-5753  
(714) 522-8088  
ILLINOIS  
NEVADA  
3375 S. Decatur Blvd.  
Suites. 22 - 24  
Las Vegas, NV 89102  
(702) 368-4277  
TENNESSEE  
1120 Elm Hill P.  
Suile 170 Nashville, TN 372  
(615) 248-3321  
1450 Feehanville Dr.  
Mt. Prospect, IL 60056-6011  
(847) 297-3100  
1970 Fulton Avenue  
Sacramento, CA 95825  
(916) 482-5197  
MARYLAND  
TEXAS  
7674 Clairemont Mesa Blvd.  
San Diego, CA 92111  
(858) 278-4471  
7397 Washington Boulevard,  
Suite 104 Elkridge, MD 21075  
(410) 796-4401  
NEW JERSEY  
12801 Stemmons Fwy Ste. 809  
Farmers Branch, TX 75234  
(972) 243-1150  
251 Herrod Blvd.  
Dayton, NJ 08810-1539  
(609) 655-1212  
16735 Saticoy St., Ste. 105  
Van Nuys, CA 91406  
(818) 782-2440  
12701 Directors Dr.  
Stafford, TX 77477-3701  
(281) 565-8665  
MASSACHUSETTS  
232 Providence Hwy.  
Westwood, MA 02090  
(781) 461-9754  
NEWYORK  
4917 Genessee Street  
Cheektowaga, NY 14225  
(716) 685-9503  
3453 IH-35 North, Ste. 101  
San Antonio, TX 78219  
(210) 228-0676  
COLORADO  
11839 E. 51st Ave.  
Denver, CO 80239-2709  
(303) 371-2850  
MINNESOTA  
6427 Penn Ave. South  
Richfield, MN 55423  
(612) 869-5199  
OREGON  
828 19th Avenue, N.W.  
Portland, OR 97209  
(503) 222-1823  
WISCONSIN  
Lincoln Plaza Shopping Ctr.  
2245 S. 108th St. West Allis, WI  
53227  
(414) 541-4776  
CUSTOMER’S RECORD  
Date Purchased  
When you need service: Send  
complete tool (prepaid) to one  
of the Makita Factory Service  
Centers listed, or to an Authorized  
Makita Service Center. Be sure  
to attach a letter to the outside of  
the carton detailing the problem  
with your tool.  
Dealer’s Name & Address  
Model No.  
Serial No.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Some dust created by power sanding, sawing, grinding, drilling, and other  
construction activities contains chemicals known to the State of California  
to cause cancer, birth defects or other reproductive harm. Some examples  
of these chemicals are:  
lead from lead-based paints,  
crystalline silica from bricks and cement and other masonry products, and  
arsenic and chromium from chemically-treated lumber.  
Your risk from these exposures varies, depending on how often you do this  
type of work. To reduce your exposure to these chemicals: work in a well  
ventilated area, and work with approved safety equipment, such as those  
dust masks that are specially designed to filter out microscopic particles.  
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of  
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.  
Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of  
Makitas Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective  
workmanship or material, Makita will repair (or at our option, replace) without charge.  
This Warranty does not apply where:  
repairs have been made or attempted by others:  
repairs are required because of normal wear and tear:  
the tool has been abused, misused or improperly maintained:  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING  
AND AFTER THE TERM OF THIS WARRANTY.  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF  
MERCHANTABILITYAND FITNESS FOR A SPECIFIC PURPOSE,AFTER THE ONE YEAR TERM OF THIS  
WARRANTY.  
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
Makita Corporation  
Anjo, Aichi, Japan  
Made in China  
Huangpu Jiang Road, Kunshan Economic & Technical Development Zone, Jiangsu P.R. China  
883508B982  
Download from Www.Somanuals.com. All Manuals Search And Download.  

KWC Indoor Furnishings S10X105 User Manual
Lasko Fan 5566 User Manual
LevelOne Switch GSW 2491TXM User Manual
Linksys Network Router WRT54GP2A AT User Manual
Loewe Projector Individual Sound Projector User Manual
Logitech Computer Keyboard K270 User Manual
Lux Products Thermostat DMH100 Series User Manual
Magnasonic Portable DVD Player DVD850 2 User Manual
Mazda Automobile CX 9 User Manual
Midland Radio Camcorder XTC300 User Manual