INSTRUCTION MANUAL
Cordless Rotary Hammer
BHR200
003091
IMPORTANT: Read Before Using.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
ENH101-14
you to lose control.
Electrical safety
For European countries only
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet
Cordless Rotary Hammer
Model No./ Type: BHR200
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
6.
7.
conditions. Water entering
a
power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
9.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
Milton Keynes, MK15 8JD, England
30.1.2009
If operating a power tool in a damp location is
unavoidable, use
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
a
ground fault circuit
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
GEA006-2
medication.
A
moment of inattention while
operating power tools may result in serious
personal injury.
General Power Tool Safety
Warnings
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
1.
2.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
Keep children and bystanders away while
operating a power tool. Distractions can cause
3.
15. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
3
Download from Www.Somanuals.com. All Manuals Search And Download.
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
terminal to another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
16. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
Power tool use and care
Service
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
29. Follow instruction for lubricating and
changing accessories.
30. Keep handles dry, clean and free from oil and
grease.
GEB046-2
CORDLESS ROTARY HAMMER
SAFETY WARNINGS
1.
2.
3.
Wear ear protectors. Exposure to noise can
cause hearing loss.
Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool
"live" and could give the operator an electric
shock.
4.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun
glasses are NOT safety glasses. It is also
highly recommended that you wear a dust
mask and thickly padded gloves.
5.
6.
Be sure the bit is secured in place before
operation.
Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
7.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
8.
9.
Hold the tool firmly with both hands.
10. Keep hands away from moving parts.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Do not point the tool at any one in the area
when operating. The bit could fly out and
injure someone seriously.
13. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
14. Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
exceed 50 ﾟ C (122 ﾟ F).
7.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Do not use dropped or struck battery.
8.
9.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.
SAVE THESE INSTRUCTIONS.
2.
3.
Never recharge
cartridge.
a
fully charged battery
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
Overcharging shortens the battery service life.
Charge the battery cartridge with room
temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).
Let a hot battery cartridge cool down before
charging it.
Charge the Nickel Metal Hydride battery
cartridge when you do not use it for more than
six months.
injury.
4.
ENC005-2
IMPORTANT SAFETY
INSTRUCTIONS
FUNCTIONAL DESCRIPTION
FOR BATTERY CARTRIDGE
CAUTION:
1.
Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
•
Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
2.
3.
Do not disassemble battery cartridge.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
1. Battery cartridge
2. Red part
3. Button
4.
5.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
2
3
1
003103
•
Always switch off the tool before insertion or
removal of the battery cartridge.
To remove the battery cartridge, withdraw it from
the tool while sliding the button on the side of the
cartridge.
To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can see
the red part on the upper side of the button, it is not
locked completely. Insert it fully until the red part
cannot be seen. If not, it may accidentally fall out of
(2) Avoid storing battery cartridge in
a
•
•
container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and
even a breakdown.
6.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
5
Download from Www.Somanuals.com. All Manuals Search And Download.
the tool, causing injury to you or someone around
you.
Do not use force when inserting the battery
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
Selecting the action mode
Rotation with hammering
•
1. Rotation with
hammering
1
2
2. Lock button
3. Pointer
Switch action
4. Change lever
1. Switch trigger
3
4
003128
1
For drilling in concrete, masonry, etc., depress the lock
button and rotate the change lever so that the pointer
points to the symbol. Use a tungsten-carbide tipped bit.
Rotation only
003104
CAUTION:
1. Rotation only
2. Pointer
1
•
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
2
Reversing switch action
003131
For drilling in wood, metal or plastic materials, depress
the lock button and rotate the change lever so that the
1. Reversing switch
lever
1
pointer points to the
wood bit.
symbol. Use a twist drill bit or
Hammering only
A
B
1. Hammering only
2. Pointer
1
003113
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the
counterclockwise rotation.
B
side for
2
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.
003133
For chipping, scaling or demolition operations, depress
the lock button and rotate the change lever so that the
pointer points to the symbol. Use a bull point, cold
chisel, scaling chisel, etc.
CAUTION:
•
•
Always check the direction of rotation before
operation.
CAUTION:
Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of
rotation before the tool stops may damage the tool.
When not operating the tool, always set the
reversing switch lever to the neutral position.
•
•
Do not rotate the change lever when the tool is
running. The tool will be damaged.
To avoid rapid wear on the mode change
mechanism, be sure that the change lever is
always positively located in one of the three action
mode positions.
•
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION:
Torque limiter
•
Always use the side grip to ensure operating safety
when drilling in concrete, masonry, etc.
The side grip swings around to either side, allowing easy
handling of the tool in any position. Loosen the side grip
by turning it counterclockwise, swing it to the desired
position and then tighten it by turning clockwise.
The torque limiter will actuate when a certain torque level
is reached. The motor will disengage from the output
shaft. When this happens, the bit will stop turning.
CAUTION:
•
As soon as the torque limiter actuates, switch off
the tool immediately. This will help prevent
premature wear of the tool.
Installing or removing the bit
Foot
1. Bit shank
2. Bit grease
1. Foot
2. Battery cartridge
2
1
2
003150
1
Clean the bit shank and apply bit grease before installing
004215
the bit.
Remove the foot when you use the battery cartridge
BH2420.
This will help to place the tool steady.
Install the foot when you use the battery cartridge
BH2433.
Insert the bit into the tool. Turn the bit and push it in until it
engages.
1. Bit
2. Chuck cover
This will help to place the tool steady.
1
1. Foot
2
2. Screw
3. Battery cartridge
003157
If the bit cannot be pushed in, remove the bit. Pull the
chuck cover down a couple of times. Then insert the bit
again. Turn the bit and push it in until it engages.
After installing, always make sure that the bit is securely
held in place by trying to pull it out.
3
1
2
004216
ASSEMBLY
To remove the bit, pull the chuck cover down all the way
and pull the bit out.
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
Side grip
1. Side grip
003166
1
003141
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Bit angle (when chipping, scaling or
demolishing)
Dust cup
1. Dust cup
1. Change lever
2. O symbol
2
1
1
001300
Use the dust cup to prevent dust from falling over the tool
and on yourself when performing overhead drilling
operations. Attach the dust cup to the bit as shown in the
figure. The size of bits which the dust cup can be
attached to is as follows.
003170
1. Change lever
1
Bit diameter
Dust cup 5
Dust cup 9
6 mm - 14.5 mm
12 mm - 16 mm
006406
003174
OPERATION
Depress the lock button and rotate the change lever so
that the pointer points to the symbol. Then make sure
that the bit is securely held in place by turning it slightly.
To change the bit angle, depress the lock button and
rotate the change lever so that the pointer points to
theOsymbol. Turn the bit to the desired angle.
Depress the lock button and rotate the change lever so
that the pointer points to the symbol. Then make sure
that the bit is securely held in place by turning it slightly.
CAUTION:
•
Always insert the battery cartridge all the way until it
locks in place. If you can see the red part on the
upper side of the button, it is not locked completely.
Insert it fully until the red part cannot be seen. If not,
it may accidentally fall out of the tool, causing injury
to you or someone around you.
•
When operating overhead, always make sure the
battery cartridge is locked securely so that it will not
be fallen out of the tool. If not, it may accidentally
fall out of the tool, causing injury to you or someone
around you.
Depth gauge
1. Depth gauge
2. Clamp screw
3. Grip base
3
1
2
Hammer drilling operation
003179
The depth gauge is convenient for drilling holes of
uniform depth. Loosen the clamp screw and adjust the
depth gauge to the desired depth. After adjusting, tighten
the clamp screw firmly.
003197
Set the change lever to the symbol.
NOTE:
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light
pressure gives best results. Keep the tool in position and
prevent it from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at an
idle, then remove the bit partially from the hole. By
•
The depth gauge cannot be used at the position
where the depth gauge strikes against the gear
housing/motor housing.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
Use the optional drill chuck assembly. When installing it,
refer to "Installing or removing the bit" described on the
previous page.
CAUTION:
Set the change lever so that the pointer points to
the symbol.
You can drill up to 13 mm diameter in metal and up to 27
mm diameter in wood.
•
There is a tremendous and sudden twisting force
exerted on the tool/bit at the time of hole
break-through, when the hole becomes clogged
with chips and particles, or when striking reinforcing
rods embedded in the concrete. Always use the
side grip (auxiliary handle) and firmly hold the tool
by both side grip and switch handle during
operations. Failure to do so may result in the loss of
control of the tool and potentially severe injury.
Use
a
cutting lubricant when drilling metals. The
exception is brass which should be drilled dry .
CAUTION:
•
•
Never use "rotation with hammering" when the drill
chuck assembly is installed on the tool. The drill
chuck assembly may be damaged.
Pressing excessively on the tool will not speed up
the drilling. In fact, this excessive pressure will only
serve to damage the tip of your bit, decrease the
tool performance and shorten the service life of the
tool.
Blow-out bulb (optional accessory)
1. Blow-out bulb
1
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
002449
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
•
Chipping/Scaling/Demolition
Replacing carbon brushes
1. Limit mark
003203
Set the change lever to the symbol.
Hold the tool firmly with both hands. Turn the tool on and
apply slight pressure on the tool so that the tool will not
bounce around, uncontrolled. Pressing very hard on the
tool will not increase the efficiency.
1
001145
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
Drilling in wood or metal
1. Drill chuck
2. Change lever
3. Pointer
2
1
3
003222
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Brush holder cap
2. Screwdriver
1
2
003228
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
•
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
SDS-Plus Carbide-tipped bits
Bull point
Cold chisel
Scaling chisel
Grooving chisel
Drill chuck assembly
Drill chuck S13
Chuck key S13
Bit grease
Side grip
Depth gauge
Blow-out bulb
Dust cup
Dust extractor attachment
Safety goggles
Plastic carrying case
Various type of Makita genuine batteries and
chargers
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Makita Corporation
Anjo, Aichi, Japan
884305F220
Download from Www.Somanuals.com. All Manuals Search And Download.
|