Makita Grinder N9501B User Manual

Disc Grinder  
100 mm (4”)  
MODEL N9501B  
DOUBLE  
INSULATION  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
w w w. m a k i t a t o o l s . c o m  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Avoid body contact with grounded sur-  
faces such as pipes, radiators, ranges and  
refrigerators. There is an increased risk of  
electric shock if your body is grounded.  
14. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions. Ordinary  
eye or sun glasses are NOT eye protection.  
6. Do not expose power tools to rain or wet  
conditions. Water entering a power tool will  
increase the risk of electric shock.  
Tool Use and Care  
15. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
7. Do not abuse the cord. Never use the cord  
to carry the tools or pull the plug from an  
outlet. Keep cord away from heat, oil,  
sharp edges or moving parts. Replace  
damaged cords immediately. Damaged  
cords increase the risk of electric shock.  
16. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
8. When operating a power tool outside, use  
an outdoor extension cord marked “W-A”  
or “W”. These cords are rated for outdoor  
use and reduce the risk of electric shock.  
17. Do not use tool if switch does not turn it  
on or off. Any tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
9. Stay alert, watch what you are doing and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
18. Disconnect the plug from the power  
source before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
19. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
10. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or long  
hair can be caught in moving parts.  
20. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edges are less likely  
to bind and are easier to control.  
11. Avoid accidental starting. Be sure switch  
is off before plugging in. Carrying tools with  
your finger on the switch or plugging in tools  
that have the switch on invites accidents.  
21. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tools  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
12. Remove adjusting keys or wrenches  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
22. Use only accessories that are recom-  
mended by the manufacturer for your  
model. Accessories that may be suitable for  
one tool, may become hazardous when used  
on another tool.  
13. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
balance enables better control of the tool in  
unexpected situations.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
24. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
electric shock or injury.  
SERVICE  
23. Tool service must be performed only by  
qualified repair personnel. Service or main-  
tenance performed by unqualified personnel  
could result in a risk of injury.  
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.  
When using an extension cord, be sure to use one heavy enough to carry the current your  
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of  
power and overheating. Table 1 shows the correct size to use depending on cord length and  
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-  
ber, the heavier the cord.  
Table 1: Minimum gage for cord  
Volts  
120 V  
Total length of cord in feet  
Ampere Rating  
25 ft.  
50 ft.  
100 ft.  
150 ft.  
More Than  
Not More Than  
AWG  
0
6
10  
12  
6
18  
18  
16  
14  
16  
16  
16  
12  
16  
14  
14  
14  
12  
12  
10  
12  
16  
Not Recommended  
SPECIFIC SAFETY RULES  
USB005-3  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to grinder safety rules. If  
you use this tool unsafely or incorrectly, you can suffer serious  
personal injury.  
1. Always use proper guard with grinding  
wheel. A guard protects operator from bro-  
ken wheel fragments.  
3. Hold tool by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring or  
its own cord. Contact with a livewire will  
make exposed metal parts of the tool live”  
and shock the operator.  
2. Accessories must be rated for at least the  
speed recommended on the tool warning  
label. Wheels and other accessories running  
over rated speed can fly apart and cause  
injury.  
4. When using depressed center grinding  
wheels, be sure to use only fiberglass-  
reinforced wheels.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Always use safety glasses or goggles.  
Ordinary eye or sun glasses are NOT  
safety glasses.  
12. Make sure cord is clear of wheel. Do not  
wrap cord around your arm or wrist. If  
control of tool is lost, cord may become  
wrapped around you and cause personal  
injury.  
6. Check the wheel carefully for cracks or  
damage  
before  
operation.  
Replace  
cracked or damaged wheel immediately.  
Run the tool (with guard) at no load for  
about a minute, holding tool away from  
others. If wheel is flawed, it will likely sep-  
arate during this test.  
13. Make sure the wheel is not contacting the  
workpiece before the switch is turned on.  
14. Before using the tool on an actual work-  
piece, let it run for a while. Watch for  
vibration or wobbling that could indicate  
poor installation or a poorly balanced  
wheel.  
7. Use only flanges specified for this tool.  
8. Be careful not to damage the spindle, the  
flange (especially the installing surface)  
or the lock nut. Damage to these parts  
could result in wheel breakage.  
15. Use the specified surface of the wheel to  
perform the grinding.  
16. Watch out for flying sparks. Hold the tool  
so that sparks fly away from you and other  
persons or flammable materials.  
9. NEVER use tool with wood cutting blades  
or other sawblades. Such blades when  
used on a grinder frequently kick and  
cause loss of control leading to personal  
injury.  
17. Do not leave the tool running. Operate the  
tool only when hand-held.  
18. Do not touch the workpiece immediately  
after operation; it may be extremely hot  
and could burn your skin.  
10. Hold the tool firmly.  
11. Keep hands away from rotating parts.  
19. ALWAYS wear proper apparel including  
long sleeve shirts, leather gloves and  
shop aprons to protect skin from contact  
with hot grindings.  
20. Use of this tool to grind or sand some  
products, paints and wood could expose  
user to dust containing hazardous sub-  
stances. Use appropriate respiratory pro-  
tection.  
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before adjusting or checking function on the  
tool.  
001036  
Switch action  
CAUTION:  
1
Before plugging in the tool, always check to see that the  
slide switch actuates properly and returns to the OFF”  
position when the rear of the slide switch is depressed.  
Switch can be locked in ONposition for ease of  
operator comfort during extended use. Apply caution  
when locking tool in ONposition and maintain firm  
grasp on tool.  
1. Slide switch  
To start the tool, slide the slide switch toward the I (ON)”  
position. For continuous operation, press the front of the  
slide switch to lock it.  
To stop the tool, press the rear of the slide switch, then slide  
it toward the O (OFF)position.  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before carrying out any work on the tool.  
001053  
Installing side grip (handle)  
CAUTION:  
Always be sure that the side grip is installed securely  
before operation.  
Screw the side grip securely on the position of the tool as  
shown in the figure.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
001072  
Installing or removing depressed center grinding  
wheel/Multi-disc  
1
2
3
WARNING:  
Always use supplied guard when depressed center  
grinding wheel/Multi-disc is on tool. Wheel can shatter  
during use and guard helps to reduce chances of  
personal injury.  
1. Lock nut  
Screw the inner flange onto the spindle. Make sure that the  
recessed side of the inner flange is placed next to the wheel.  
Hold the spindle with the wrench so that it cannot revolve,  
then use the lock nut wrench to secure the inner flange. Fit  
the wheel/disc on the inner flange and screw the lock nut  
onto the spindle.  
2. Depressed center grinding wheel/  
Multi-disc  
3. Inner flange  
001085  
To tighten the lock nut, hold the spindle with the wrench so  
that it cannot revolve, then use the lock nut wrench and  
securely tighten clockwise.  
1
To remove the wheel, follow the installation procedure in  
reverse.  
2
1. Lock nut wrench  
2. Wrench  
001097  
Installing or removing flex wheel  
(optional accessory)  
1
2
3
4
WARNING:  
Always use supplied guard when flex wheel is on tool.  
Wheel can shatter during use and guard helps to reduce  
chances of personal injury.  
Follow instructions for depressed center grinding wheel/  
Multi-disc but also use plastic pad over wheel. See order of  
assembly on accessories page in this manual.  
1. Lock nut  
2. Flex wheel  
3. Plastic pad  
4. Inner flange  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
001108  
Installing or removing abrasive disc  
(optional accessory)  
1
2
NOTE:  
3
Use sander accessories specified in this manual. These  
must be purchased separately.  
Mount the rubber pad onto the spindle. Fit the disc on the  
rubber pad and screw the lock nut onto the spindle. To  
tighten the lock nut, hold the spindle with the wrench so that  
it cannot revolve, then use the lock nut wrench and securely  
tighten clockwise.  
1. Lock nut  
2. Abrasive disc  
3. Rubber pad  
To remove the disc, follow the installation procedure in  
reverse.  
OPERATION  
WARNING:  
It should never be necessary to force the tool. The  
weight of the tool applies adequate pressure. Forcing  
and excessive pressure could cause dangerous wheel  
breakage.  
ALWAYS replace wheel if tool is dropped while grinding.  
NEVER bang or hit grinding disc or wheel onto work.  
Avoid bouncing and snagging the wheel, especially  
when working corners, sharp edges etc. This can cause  
loss of control and kickback.  
NEVER use tool with wood cutting blades and other  
sawblades. Such blades when used on a grinder  
frequently kick and cause loss of control leading to  
personal injury.  
CAUTION:  
After operation, always switch off the tool and wait until  
the wheel has come to a complete stop before putting  
the tool down.  
001122  
Grinding and sanding operation  
ALWAYS hold the tool firmly with one hand on housing and  
the other on the side handle. Turn the tool on and then apply  
the wheel or disc to the workpiece.  
In general, keep the edge of the wheel or disc at an angle of  
about 15 degrees to the workpiece surface.  
During the break-in period with a new wheel, do not work the  
15˚  
A
B
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
grinder in the B direction or it will cut into the workpiece.  
Once the edge of the wheel has been rounded off by use, the  
wheel may be worked in both A and B direction.  
001137  
Operation with wire cup brush  
(optional accessory)  
1
CAUTION:  
Check operation of brush by running tool with no load,  
insuring that no one is in front of or in line with brush.  
Do not use brush that is damaged, or which is out of  
balance. Use of damaged brush could increase potential  
for injury from contact with broken brush wires.  
1. Wire cup brush  
Unplug tool and place it upside down allowing easy access  
to spindle. Remove any accessories on spindle. Thread wire  
cup brush onto spindle and tighten with supplied wrench.  
When using brush, avoid applying too much pressure which  
causes over bending of wires, leading to premature break-  
age.  
001230  
Operation with wire wheel brush  
(optional accessory)  
1
CAUTION:  
Check operation of wire wheel brush by running tool with  
no load, insuring that no one is in front of or in line with  
the wire wheel brush.  
Do not use wire wheel brush that is damaged, or which  
is out of balance. Use of damaged wire wheel brush  
could increase potential for injury from contact with  
broken wires.  
1. Wire wheel brush  
ALWAYS use guard with wire wheel brushes, assuring  
diameter of wheel fits inside guard. Wheel can shatter  
during use and guard helps to reduce chances of  
personal injury.  
Unplug tool and place it upside down allowing easy access  
to spindle. Remove any accessories on spindle. Thread wire  
wheel brush onto spindle and tighten with the wrenches.  
When using wire wheel brush, avoid applying too much pres-  
sure which causes over bending of wires, leading to prema-  
ture breakage.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
001117  
Operation with abrasive cut-off wheel  
(optional accessory)  
1
2
WARNING:  
3
4
When using an abrasive cut-off wheel, be sure to use  
only the special wheel guard designed for use with cut-  
off wheels.  
NEVER use cut-off wheel for side grinding.  
1. Lock nut  
2. Abrasive cut-off wheel  
3. Inner flange  
4. Wheel guard for cut-off wheel  
During cutting operations, never change the angle of the  
wheel. Placing side pressure on the cut-off wheel (as in  
grinding) will cause the wheel to crack and break, causing  
serious personal injury.  
MAINTENANCE  
CAUTION:  
001162  
Always be sure that the tool is switched off and  
unplugged before attempting to perform inspection or  
maintenance.  
1
The tool and its air vents have to be kept clean. Regularly  
clean the tools air vents or whenever the vents start to  
become obstructed.  
2
1. Exhaust vent  
2. Inhalation vent  
001145  
Replacing carbon brushes  
Remove and check the carbon brushes regularly. Replace  
when they wear down to the limit mark. Keep the carbon  
brushes clean and free to slip in the holders. Both carbon  
brushes should be replaced at the same time. Use only iden-  
tical carbon brushes.  
1
1. Limit mark  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
001149  
Use a screwdriver to remove the brush holder caps. Take out  
the worn carbon brushes, insert the new ones and secure  
the brush holder caps.  
2
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
1
1. Brush holder cap  
2. Screwdriver  
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory  
or attachment for its stated purpose.  
Your tool is supplied with a guard for use with a  
depressed center grinding wheel, multi-disc, flex wheel  
and wire wheel brush. A cut-off wheel can also be used  
with an optional guard. If you decide to use your Makita  
grinder with approved accessories which you purchase  
from your Makita distributor or factory service center, be  
sure to obtain and use all necessary fasteners and  
guards as recommended in this manual. Your failure to  
do so could result in personal injury to you and others.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
001181  
2
9
1
3
3
3
13  
14  
4
5
4
7
10  
11  
12  
4
15  
6
8
6
6
N9501B  
Grip 36  
1
2
3
Grip holder  
Wheel guard  
Inner flange 35  
4
5
Depressed center grinding wheel/Multi-disc  
Lock nut 10-35  
6
7
Plastic pad  
8
Flex wheel  
9
Rubber pad 76  
10  
11  
12  
13  
14  
15  
-
Abrasive disc  
Sanding lock nut 10-30  
Wire wheel brush  
Wire cup brush  
Wheel guard (For cut-off wheel)  
Cut-off wheel  
Wrench 14  
-
Lock nut wrench 20  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Class  
Postage  
Required  
Post Office will  
not deliver  
without proper  
postage.  
Makita U.S.A., Inc.  
14930 Northam Street  
La Mirada, CA 90638-5753  
Fold  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAIL THIS PORTION  
Your answers to the following questions are appreciated.  
1.This product was purchased from:  
3. How did you learn about this product:  
Home Center  
Other (  
)
Magazine  
Radio  
Hardware/Lumber Store  
Tool Distributor  
From Dealer  
Newspaper  
Store Display  
Catalog  
Exhibition  
From Friend  
Previous Usage  
Other (  
Industrial Supply  
Construction Supply  
)
2. Use of the product is intended for:  
4. Most favored points are:  
Construction Trade  
Industrial Maintenance  
Home Maintenance  
Hobby  
Design  
Repair Service  
Durability  
Power  
Features  
Size  
Price  
Other (  
)
Other (  
)
Makita Brand  
5. Any comments:  
DATE PURCHASED  
MONTH  
MODEL NO.  
DAY  
YEAR  
SERIAL NO.  
STATUS  
SEX  
Married Single  
M
F
INTL.  
LAST NAME / COMPANY NAME  
STREET ADRESS  
CITY  
AREA  
CODE  
STATE  
ZIP CODE  
PHONE  
40-49  
Under 19  
20-29  
30-39  
50-60  
Over 60  
AGE:  
BE SURE TO COMPLETE THE CUSTOMERS PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.  
Please return this portion by facsimile or mail.  
Facsimile No: (714) 522-8133  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
FACTORY SERVICE CENTERS  
1-800-4-MAKITA  
RETAIN THIS PORTION FOR YOUR RECORDS  
ALABAMA  
COLORADO  
KENTUCKY  
NEW MEXICO  
PUERTO RICO  
2365 Pelham Parkway  
Pelham, AL 35124  
(205) 620-1791  
11839 E. 51st Ave.  
Denver, CO 80239-2709  
(303) 371-2850  
1215 S. Hurstbourne Parkway  
Louisville, KY 40222  
(502) 326-3740  
5805 Menaul Blvd. NE  
Albuquerque, NM 87110  
(505) 881-4619  
200 Guayama St.  
Hato Rey, PR 00917  
(787) 250-8776  
ARIZONA  
CONNECTICUT  
508 Spring St.  
Windsor Locks, CT 06096  
(860) 292-6405  
LOUSIANA  
NEWYORK  
TENNESSEE  
3707 E. Broadway Rd., Ste. 6  
Phoenix, AZ 85040  
(602) 437-2850  
5626 Jefferson Hwy.  
Harahan, LA 70123  
(504) 733-4138  
4917 Genessee Street  
Cheektowaga, NY 14225  
(716) 685-9503  
4655 Nolensville Rd.  
Nashville, TN 37211  
(615) 331-9922  
131-35 31st Ave.  
Flushing, NY 11354  
(718) 886-0971  
ARKANSAS  
FLORIDA  
MARYLAND  
TEXAS  
Shackleford Shopping Center  
240 South Shackleford Rd.,  
Ste. C  
620 Douglas Ave. Suite 1302  
Altamonte Springs, FL 32714  
(407) 774-6000  
7541 - 45 Ritchie Highway  
Glen Burnie, MD 21061  
(410) 590-0160  
12801 Stemmons Fwy Ste. 809  
Farmers Branch, TX 75234  
(972) 243-1150  
Little Rock, AR 72211  
(501) 224-5733  
NORTH CAROLINA  
3501-G S. Tryon St.  
Charlotte, NC 28217  
(704) 527-0611  
750 East Sample Road  
Pompano Beach, FL 33064  
(954) 781-6333  
12701 Directors Dr.  
Stafford, TX 77477-3701  
(281) 565-8665  
MASSACHUSETTS  
232 Providence Hwy.  
Westwood, MA 02090  
(617) 461-9754  
CALIFORNIA  
41850 Christy St.  
Fremont, CA 94538-5107  
(510) 657-9881  
Thompson Center Waters  
5501 W. Waters Ave., Ste. 406  
Tampa, FL 33634  
3453 IH-35 North, Ste. 101  
San Antonio, TX 78219  
(210) 228-0676  
OHIO  
6253 E. Main St.  
Columbus, OH 43213  
(614) 860-0222  
(813) 886-8292  
MICHIGAN  
1421 N. Clovis Ave., Ste. 112  
Fresno, CA 93727  
(559) 252-5166  
37454 Ann Arbor Trail  
Livonia, MI 48150  
(313) 432-1012  
UTAH  
GEORGIA  
6379 Pearl Road  
Parma Heights, OH 44130  
(440) 843-7555  
145 E. 1300 S., Ste. 101  
Salt Lake City, UT 84115  
(801) 359-3410  
4680 River Green Parkway  
Duluth, GA 30096-2566  
(770) 476-8911  
14930 Northam St.  
La Mirada, CA 90638-5753  
(714) 522-8088  
MINNESOTA  
6427 Penn Ave. South  
Richfield, MN 55423  
(612) 869-5199  
1617 E. Kemper Rd.  
Sharonville, OH 45246  
(513) 771-0788  
VIRGINIA  
5760 Northampton Blvd,. Ste.  
102  
Virginia Beach, VA 23455  
(757) 460-0280  
1970 Fulton Avenue  
Sacramento, CA 95825  
(916) 482-5197  
HAWAII  
4510 Salt Lake Blvd., Suite A7  
Honolulu, HI 96818  
(808) 847-0038  
MISSOURI  
OKLAHOMA  
1440 South EStreet  
San Bernardino, CA 92408  
(909) 885-1289  
9876 Watson Road  
St. Louis, MO 63126-2221  
(314) 909-9889  
552 E. Memorial Road  
Oklahoma City, OK 73114  
(405) 752-2655  
ILLINOIS  
WASHINGTON  
1450 Feehanville Dr.  
Mt. Prospect, IL 60056-6011  
(847) 297-3100  
22220 84th Ave. So., Bldg. A  
Kent, WA 98032  
(253) 395-8055  
7674 Clairemont Mesa Blvd.  
San Diego, CA 92111  
(858) 278-4471  
NEBRASKA  
OREGON  
4129 S. 84th St.  
Omaha, NE 68127  
(402) 597-2925  
828 19th Avenue., N.W.  
Portland, OR 97209  
(503) 222-1823  
1714 E.McFadden Ave., Unit M  
Santa Ana, CA 92705  
(714) 667-5066  
INDIANA  
WISCONSIN  
8403 Michigan Road, Unit 1  
Indianapolis, IN 46268  
(317) 334-9980  
Lincoln Plaza Shopping Ctr.  
2245 S. 108th St. West Allis, WI  
53227  
NEVADA  
3375 S. Decatur Blvd.  
Suites. 22 - 24  
Las Vegas, NV 89102  
(702) 368-4277  
PENNSYLVANIA  
Springwater Plaza  
364 Wilmington W. Chester  
Pike  
Glen Mills, PA 19342  
(610) 459-4122  
1565 Winchester B.  
Campbell, CA 95008-0501  
(408) 379-0377  
(414) 541-4776  
KANSAS  
8819 W. 95th St.  
Overland Park, KS 66212  
(913) 642-1111  
16735 Saticoy St., Ste. 105  
Van Nuys, CA 91406  
(818) 782-2440  
NEW JERSEY  
6200 Babcock Blvd  
Pittsburgh, PA 15237  
(412) 366-6363  
251 Herrod Blvd.  
Dayton, NJ 08810-1539  
(609) 655-1212  
CUSTOMERS RECORD  
Date Purchased  
When you need service: Send  
complete tool (prepaid) to one  
of the Makita Factory Service  
Centers listed, or to an Authorized  
Makita Service Center. Be sure  
to attach a letter to the outside of  
the carton detailing the problem  
with your tool.  
Dealers Name & Address  
Model No.  
Serial No.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Some dust created by power sanding, sawing, grinding, drilling, and other  
construction activities contains chemicals known to the State of California  
to cause cancer, birth defects or other reproductive harm. Some examples  
of these chemicals are:  
lead from lead-based paints,  
crystalline silica from bricks and cement and other masonry products, and  
arsenic and chromium from chemically-treated lumber.  
Your risk from these exposures varies, depending on how often you do this  
type of work. To reduce your exposure to these chemicals: work in a well  
ventilated area, and work with approved safety equipment, such as those  
dust masks that are specially designed to filter out microscopic particles.  
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of  
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.  
Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of  
Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective  
workmanship or material, Makita will repair (or at our option, replace) without charge.  
This Warranty does not apply where:  
repairs have been made or attempted by others:  
repairs are required because of normal wear and tear:  
the tool has been abused, misused or improperly maintained:  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING  
AND AFTER THE TERM OF THIS WARRANTY.  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF  
"MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE-YEAR TERM OF  
THIS WARRANTY.  
This Warranty gives you specific legal rights, and you may also have other rights which vary form state to state.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
Makita Corporation  
3-11-8, Sumiyoshi-cho,  
Anjo, Aichi 446-8502 Japan  
883225F061  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Leica Mouse NCL L CD33 User Manual
Lightolier Indoor Furnishings 1002P1 User Manual
Magnavox CRT Television PRI907X User Manual
Makita Cordless Drill DDF481 User Manual
Maytag Clothes Dryer W10306460A SP User Manual
Maytag Range W10667173A User Manual
Meco Charcoal Grill Bonza Series User Manual
Melissa Espresso Maker 245 017 User Manual
Metrologic Instruments Barcode Reader MLPN 2178 User Manual
Microsoft Computer Hardware 64 MHz 32 Bit Floating Point Central Processing Unity 1 Mbyte Memory State Logic User Manual