Magnavox Flat Panel Television 26MF330B User Manual

Owner’s manual  
Manuel du propriétaire  
Manual del propietario  
32MF330B  
26MF330B  
LCD TV  
1-866-341-3738  
1-866-341-3738  
1-866-341-3738  
Quick Use Guide Inside!  
Guide d’usage Rapide Incluse!  
Guía de Uso Rápido Incluida!  
MODEL NUMBER  
SERIAL NUMBER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
IMPORTANT SAFETY INSTRUCTIONS  
Read before operating equipment  
1. Read these instructions.  
2. Keep these instructions.  
16. Tilt/Stability - All televisions must comply with recommended  
international global safety standards for tilt  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with a dry cloth.  
and stability properties of its cabinet design.  
• Do not compromise these design standards by applying  
excessive pull force to the front, or top, of the cabinet  
which could ultimately overturn the product.  
• Also, do not endanger yourself, or children, by placing  
electronic equipment/toys on the top of the cabinet. Such  
items could unsuspectingly fall from the top of the set and  
cause product damage and/or personal injury.  
17. Wall or Ceiling Mounting -The appliance should be  
mounted to a wall or ceiling only as recommended by the  
manufacturer.  
18. Power Lines - An outdoor antenna should be located  
away from power lines.  
19. Outdoor Antenna Grounding - If an outside antenna  
is connected to the receiver, be sure the antenna system is  
grounded so as to provide some protection against voltage  
surges and built up static charges.  
7. Do not block any of the ventilation openings.  
Install in accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators, heat  
registers, stoves, or other apparatus (including ampliers)  
that produce heat.  
9. Do not defeat the safety purpose of the polarized or  
grounding-type plug.A polarized plug has two blades with  
one wider than the other.A grounding type plug has two  
blades and third grounding prong.The wide blade or third  
prong are provided for your safety.When the provided  
plug does not t into your outlet, consult an electrician for  
replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched  
particularly at plugs, convenience receptacles, and the point  
where they exit from the apparatus.  
11. Only use attachments/accessories specied by the  
manufacturer.  
Section 810 of the National Electric Code,ANSI/NFPA  
No. 70-1984, provides information with respect to proper  
grounding of the mast and supporting structure, ground-  
ing of the lead-in wire to an antenna discharge unit, size of  
grounding connectors, location of antenna-discharge unit,  
connection to grounding electrodes, and requirements for  
the grounding electrode. See Figure below.  
12.  
Use only with a cart, stand, tripod, bracket, or table  
specied by the manufacturer, or sold with the appara-  
tus.When a cart is used, use caution when moving the  
cart/apparatus combination to avoid injury from tip-over.  
20. Object and Liquid Entry - Care should be taken so  
that objects do not fall and liquids are not spilled into the  
enclosure through openings.  
13. Unplug this apparatus during lightning storms or when un-  
used for long periods of time.  
14. Refer all servicing to qualied service personnel. Servicing is  
required when the apparatus has been damaged in any way,  
such as power-supply cord or plug is damaged, liquid has  
been spilled or objects have fallen into apparatus, the appara-  
tus has been exposed to rain or moisture, does not operate  
normally, or has been dropped.  
21. Battery Usage CAUTION -To prevent battery  
leakage that may result in bodily injury, property damage,  
or damage to the unit:  
• Install all batteries correctly, with + and - aligned as  
marked on the unit.  
• Do not mix batteries (old and new or carbon and  
alkaline, etc.).  
• Remove batteries when the unit is not used for a long  
time.  
15. Damage Requiring Service -The appliance should be  
serviced by qualied service personnel when:  
A. The power supply cord or the plug has been damaged;  
B. Objects have fallen, or liquid has been spilled into the  
appliance;  
C. The appliance has been exposed to rain  
D. The appliance does not appear to operate normally or  
exhibits a marked change in performance;  
E. The appliance has been dropped, or the enclosure damaged.  
Note to the CATV system installer :This reminder is provided to call the CATV system installer’s attention to Article  
820-40 of the NEC that provides guidelines for proper grounding and, in particular, species that the cable ground shall  
be connected to the grounding system of the building, as close to the point of cable entry as practical.  
Example of Antenna Grounding as  
per NEC - National Electric Code  
GROUND CLAMP  
ANTENNA LEAD IN WIRE  
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)  
GROUNDING CONDUCTORS (NEC SECTION 810-21)  
GROUND CLAMPS  
ELECTRIC SERVICE EQUIPMENT  
POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
FCC WARNING  
This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may cause harmful interference  
unless the modifications are expressly approved in the manual. The user could lose the authority to operate this apparatus if an  
unauthorized change or modification is made.  
RADIO-TV INTERFERENCE  
This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This apparatus  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.  
If this apparatus does cause harmful interference to radio or television reception, which can be determined by turning the apparatus off  
and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the apparatus and receiver.  
3) Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.  
4) Consult the dealer or an experienced radio/TV technician for help.  
DECLARATION OF CONFORMITY  
Trade Name: MAGNAVOX  
Responsible Party: FUNAI CORPORATION, Inc.  
Address: 19900 Van Ness Avenue, Torrance, CA 90501 U.S.A.  
Telephone Number: 1-866-341-3738  
Model: 32MF330B /26MF330B  
This Class B digital apparatus complies with Canadian ICES-003. StandardTelevision Receiving Apparatus, Canada BETS-7/NTMR-7  
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.  
WARNING: Batteries (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire or the like.  
Disconnect the mains plug to shut off when find trouble or not in use.The mains plug shall remain readily operable.  
This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided.  
Make sure to leave a space of 3.2 inches (8cm) or more around this apparatus.  
WARNING: To prevent injury, this apparatus must be securely attached to the wall in accordance with the instructions.  
Like all LCD products, this set contains a lamp with Mercury, please dispose of according to all Local, State and  
Federal laws. For the disposal or recycling information, contact:  
Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or  
climbing on it. A falling unit can cause serious injury or even death.  
NOTE ABOUT RECYCLING  
This unit’s packaging materials are recyclable and  
can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or  
incinerated but disposed of in accordance with your  
local regulations concerning chemical wastes.  
Trademark Information  
HDMI, the HDMI Logo, and High-Denition Multimedia Interface  
are trademarks or registered trademarks of HDMI Licensing LLC  
in the United States and other countries.  
WHEN CARRYINGTHIS UNIT  
At least 2 people are required when  
carrying this unit.  
Make sure to hold the upper and bottom  
frames of the unit rmly as illustrated.  
TO AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
Manufactured under license from Dolby Laboratories. Dolby and  
the double-D symbol are trademarks of Dolby Laboratories.  
Do not handle the AC power cord with wet hands.  
Do not pull on the AC power cord when disconnecting it from an  
AC outlet. Grasp it by the plug.  
Do not put your ngers or objects into the unit.  
LOCATION AND HANDLING  
Do not install the unit in direct sunlight, near strong magnetic  
elds, or in a place subject to dust or strong vibration.  
Avoid a place with drastic temperature changes.  
Install the unit in a horizontal and stable position. Do not place  
anything directly on top or bottom of the unit. Depending on  
your external devices, noise or disturbance of the picture and/or  
sound may be generated if the unit is placed too close to them.  
In this case, please ensure enough space between the external  
devices and the unit.  
Depending on the environment, the temperature of this unit may  
increase slightly.This is not a malfunction.  
Be sure to unplug the AC power cord from the AC outlet before  
carrying the unit.  
ENERGY STAR® is a joint program of the U.S. Environmental  
Protection Agency and the U.S. Department of Energy helping  
us all save money and protect the environment through energy  
efcient products and practices.  
Consumer Notice:  
ThisTV has been set to maximize energy efciency while  
delivering the best possible picture using the factory installed  
home mode settings.  
Changing or enabling other features in thisTV (e.g. brightened  
backlighting) will possibly increase energy consumption beyond  
the original ENERGY STAR® qualied limits.  
The American Academy of Pediatrics discourages television  
viewing for children younger than two years of age.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
Features  
INTRODUCTION  
• DTV/TV/CATV  
You can use your remote control to select channels which  
are broadcast in digital format and conventional analog  
format. Also, cable subscribers can access their cableTV  
channels.  
Contents  
• Information Display (ATSC only)  
Important Safety Instructions  
Trademark Information  
3
4
You can display the title, contents and other information of  
the current DTV program on theTV screen.  
• Autoprogram  
INTRODUCTION  
This unit automatically scans and memorizes channels  
available in your area, eliminating difficult setup procedures.  
• Child Lock  
This feature allows you to block children’s access to  
inappropriate programs.  
• Closed Caption Decoder  
Built-in closed caption decoder displays text for closed  
caption supported programs.  
• MTS/SAPTuner  
Audio can be selected from the remote control.  
• Auto Shut Off Function  
Features  
5
6
6
6
6
7
8
9
9
Supplied Accessories  
Symbols Used in this Manual  
Attaching the Base  
Fixing the Unit onYour Furniture  
Control Panel  
Terminals  
Remote Control Function  
Installing the Batteries  
If there is no input signal and no operation for 15 minutes,  
the unit will turn off automatically.  
PREPARATION  
Antenna Connection  
10  
10  
11  
14  
14  
15  
• SleepTimer  
Connection to Cable Receiver or Satellite Box  
External Device Connection  
Cable Management  
Plug In the AC Power Cord  
Initial Setup  
This feature will automatically turn off the power of the unit at  
a specific time.  
• Choices for On-screen Language  
Select your on-screen language:  
English, Spanish or French.  
• Stereo Sound Function  
WATCHINGTV  
• PLL Frequency SynthesizedTuning  
SleepTimer  
16  
16  
16  
16  
17  
17  
18  
18  
18  
Provides free and easy channel selection and lets you tune  
directly to any channel using the number and decimal point  
Switching Each Input Mode  
Freeze Mode  
Channel Selection  
TV Screen Display Mode  
Sound Functions  
TV Screen Information  
Reducing the Brightness  
Fun-Link Options  
" " buttons on the remote control.  
• Various Adjustment for Picture and Sound  
Customizes image quality suitable for your room and sets  
your sound preference.  
• Fun-Link via HDMI Link  
(HDMI Cable not Included)  
Fun-Link allows your other HDMI link devices (such as  
Magnavox DVD) to be controlled by the HDMI cable  
connected to yourTV.  
OPTIONAL SETTING  
• HDMI Input  
Main Menu  
19  
19  
20  
20  
21  
21  
22  
22  
24  
27  
29  
30  
30  
30  
When using HDMI1 Input, you can enjoy this unit as a PC  
monitor if your PC has a DVI output terminal.  
• ComponentVideo Input  
• S-Video Input  
• AV Input  
• Digital Audio Output  
• Analog Audio Output  
Autoprogram  
Channel List  
Add Channels  
Antenna Conrmation  
Language Selection  
Picture Adjustment  
Sound Adjustment  
Closed Caption  
Child Lock  
Fun-Link  
Energy Saving Mode  
Location  
Current Software Info  
© 2010 Funai Electric Co., Ltd.  
All rights reserved. No part of this manual may be reproduced, copied,  
transmitted, disseminated, transcribed, downloaded or stored in any storage  
medium, in any form or for any purpose without the express prior written  
consent of Funai. Furthermore, any unauthorized commercial distribution of this  
manual or any revision hereto is strictly prohibited.  
Information in this document is subject to change without notice. Funai  
reserves the right to change the content herein without the obligation to  
notify any person or organization of such changes.  
TROUBLESHOOTING  
FAQ  
31  
32  
Troubleshooting Guide  
INFORMATION  
with the  
design is a registered trademark of Funai Electric Co.,  
Glossary  
34  
34  
35  
35  
35  
37  
Ltd. and may not be used in any way without the express written consent  
of Funai. All other trademarks used herein remain the exclusive property  
of their respective owners. Nothing contained in this manual should be  
construed as granting, by implication or otherwise, any license or right to  
use any of the trademarks displayed herein. Misuse of any trademarks or  
any other content in this manual is strictly prohibited. Funai shall aggressively  
enforce its intellectual property rights to the fullest extent of the law.  
Maintenance  
General Specications  
Electrical Specication  
Other Specications  
Limited Warranty  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Supplied Accessories  
Attaching the Base  
You must attach the base to the unit to have it as a table top  
unit. Be sure the front and rear of the base match the proper  
direction.  
Owner’s manual  
25839  
Quick Start  
25840  
26281  
(1EMN  
)
32MF330B: 1EMN  
(
)
26MF330B: 1EMN  
1
Spread a thick and soft  
cloth over a table as  
shown.  
Place the main unit face  
down onto it. Make sure  
not to damage the screen.  
At least 2 people are  
required for this step.  
Remote control  
(NF804UD)  
Registration card  
(1EMN24699)  
2 Insert 2 hooks under the  
bottom of the main unit  
into base holes. (shown by  
arrow ), then move the  
base in the direction as  
shown by arrow until it  
stops and the 4 mounting  
holes are aligned. Make  
sure not to put the AC  
power cord between the  
base and the unit.  
Batteries  
(AAA, 1.5V x 2)  
Screw kit  
3
Drive Phillips pan screws  
into the 4 threaded holes  
at the bottom of the base  
until they are tight.  
for attaching the base  
19881  
23705  
32MF330B: 1ESA  
(
)
26MF330B: 1ESA  
To remove the base from this unit  
Unscrew the Phillips pan screws on step 3  
After the screws are removed, move the base in the opposite direction as  
shown by arrow on step 2, then pull the base up toward the rear of the  
If you need to replace these accessories, please refer  
to the part No. with the illustrations and call our toll  
free customer support line found on the cover of this  
manual.  
unit. Be careful not to drop the base when you remove it.  
Note  
When attaching the base, ensure that all screws are tightly fastened. If the  
base is not properly attached, it could cause the unit to fall, resulting in  
injuries as well as damage to the unit.  
Note  
If you lose the screws, please purchase M4×20 Phillips head screws at your  
local store.  
Make sure to use a table which can support the weight of this unit and is  
larger than this unit.  
Make sure the table is in a stable location.  
When attaching the base, ensure that FRONT written on the base is  
upward. If it's not upward, the 2 hooks don't t in the base.  
Symbols Used in this Manual  
The following is the description for the symbols used in  
this manual. Description refers to:  
Fixing the Unit onYour Furniture  
Screw this unit on your furniture tightly using wood screws  
ATSC  
NTSC  
: DigitalTV operation  
:Analog/CableTV operation  
(not supplied) in the 2 holes at the back of the base as shown.  
Recommended screw dimension : 5.1 x 20 mm  
If neither symbol appears, the operation is applicable to  
both.  
rear of this unit  
Note  
When you remove this unit make sure to unscrew the wood screws from  
your Wood Stand, Furniture and other wood item.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
Control Panel  
32MF330B  
POWER  
p.15  
p.16  
2 CHANNEL +/  
Press to select channels or move up ( ) / down (–)  
through the main menu items.  
+
3 MENU  
p.19  
p.17  
4 VOLUME +/  
Press to adjust the volume or move right ( ) / left (–)  
through the main menu items.  
+
5 Infrared sensor window  
5
Receives infrared rays transmitted from the remote  
control.  
6
7
6 POWER ON indicator  
Lights up green when power is on.  
-
-
POWER  
CHANNEL  
VOLUME  
MENU  
+
+
7 STAND 
BY indicator  
Lights up red when power is off.  
4
3
2
1
26MF330B  
7
6
5
STAND BY  
POWER ON  
-
POWER  
VOLUME  
+
MENU  
-
CHANNEL  
+
4
3
2
1
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Terminals  
32MF330B  
8 S-Video / CompositeVideo / Audio (L/R)  
Input jacks forVIDEO  
p.12, 13  
9 HDMI 2 Input jack  
p.10, 11  
8
9
Rear Panel  
10 AC power cord  
11 Cable management  
p.14  
p.14  
*
10  
11  
12 ComponentVideo and Audio (L/R) Input jacks  
p.10, 11, 12  
12  
13 Audio (L/R) Output jacks  
p.13  
14 Audio (L/R) Input jacks for HDMI 1  
p.12, 14  
17  
18  
Audio cable connection from a DVI device.  
When you connect your PC that has a DVI terminal, use  
a stereo mini plug conversion cable as well.  
13  
14  
(For HDMI 1 Input jack only)  
15  
16  
15 Digital Audio Output jack  
16 Antenna Input jack  
17 HDMI 1 Input jack  
p.13  
p.10  
p.10, 11, 12, 14  
HDMI connection for HDMI or DVI device.When you  
connect your PC that has a DVI terminal, you can enjoy  
26MF330B  
this unit as a PC monitor.  
*
18 HDMI 3 Input jack  
p.10, 11  
9
8
11  
10  
16  
18  
17  
12  
15  
13  
14  
Note for service terminal  
service terminal (service use only)  
*
Use this terminal only when a software update is necessary.  
User should not connect any devices to the service terminal such as digital  
camera, keyboard, mouse, etc. (because these will not work).  
The software update is, in most cases, handled by an authorized service  
person or in some circumstances the user may be asked to do the software  
update themselves.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
Remote Control Function  
1
(power)  
p.15  
p.17  
p.16  
p.16  
2 SAP  
3 SOURCE  
4 FREEZE  
1
2
3
Press to freeze screen image.  
10  
11  
12  
13  
5 OK  
p.15  
p.15  
p.18  
6 ///(cursor)  
7 BACK  
Press to return to the previous menu operation.  
4
5
8 VOL +/−  
p.17  
p.16  
9 PREV CH  
Press to return to previously viewed channel.  
6
7
10 SLEEP  
11 FORMAT  
p.16  
p.17  
Press to select aspect ratio available for theTV screen.  
14  
15  
12 RED/GREEN/BLUE/YELLOW  
p.29  
Functionally useful for Fun-Link.  
13 MENU  
p.19  
14 INFO  
15 REV E/FWD D  
p.18  
p.29  
16  
Press to search backward or forward through the disc  
PLAY B  
Press to begin the disc playback.  
SKIP H/SKIP G  
Press to skip backward or forward chapters, titles or  
tracks of the disc.  
p.29  
17  
18  
8
9
p.29  
PAUSE F  
Press to pause the disc playback.  
STOP C  
p.29  
19  
20  
p.29  
Press to stop the disc playback  
16 MUTE  
p.17  
p.16  
p.18  
17 CH +/−  
18 ECO  
Press to reduce the brightness.  
19 Number buttons  
(dot)  
p.16  
Press to shift the subchannel from the main channel.  
20 FUN-LINK OPTIONS p.18, 29  
When using a universal remote control to operate this unit.  
Press to call up various menu from your Fun-link device  
connected through an HDMI cable.  
Make sure the component code on your universal remote control is set  
to our brand. Refer to the manual accompanying your remote control for  
more details.  
We do not guarantee 100% interoperability with all universal remote  
controls.  
Installing the Batteries  
Install the batteries (AAA, 1.5V x 2) matching the polarity  
Note  
Buttons in gray background (  
) are not available unless you are  
connected to devices that are compatible with Fun-Link function.  
We do not guarantee 100% interoperability with other brands of HDMI link  
compliant devices.  
indicated inside battery compartment of the remote control.  
Battery Precautions:  
Be sure to follow the correct polarity as indicated in the battery  
compartment. Reversed batteries may cause damage to the device.  
Do not mix different types of batteries together (e.g.Alkaline and  
Carbon-Zinc, or rechargeable batteries like ni-cad, ni-mh, etc) or old  
batteries with fresh ones.  
If the device is not to be used for a long period of time, remove the  
batteries to prevent damage or injury from possible battery leakage.  
Do not try to recharge batteries; they can overheat and rupture.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Connection to Cable Receiver or  
Satellite Box  
PREPARATION  
Use an HDMI or component video cables to connect the  
HDMI or the ComponentVideo Input jacks of the unit to  
the HDMI or the component video output jacks of the cable  
receiver/satellite box.  
If you connect to the unit’s ComponentVideo Input jacks,  
connect audio cables to the Audio L/R Input jacks right beside  
the ComponentVideo connector.  
No supplied cables are used with these connections:  
Please purchase the necessary cables at your local store.  
High Speed HDMI cable (also known as HDMI category 2  
cable) is recommended for the better compatibility.  
Before you connect:  
Be sure your antenna or other device is connected properly  
before plugging in the AC power cord.  
e.g.)  
32MF330B  
satellite dish  
Antenna Connection  
Connect the RF coaxial cable on your home outlet to the  
antenna input jack of this unit.  
RF coaxial cable  
cable receiver/  
satellite box  
ANT IN  
or  
e.g.)  
STEREO  
PCM  
32MF330B  
cableTV signal  
including PPV  
AUDIO OUT  
COMPONENT VIDEO OUT  
HDMI OUT  
L
R
Y
Pb/Cb  
Pr/Cr  
or  
(green) (blue)  
(red)  
component video cables  
(red/blue/green)  
VHF/UHF  
analog  
rear of this unit  
or  
and audio cables  
HDMI cable  
DTV antenna  
RF coaxial cable  
or  
or  
cableTV signal  
RF coaxial cable  
26MF330B  
or  
rear of this unit  
Once connections are completed, turn on the unit and begin initial  
setup. Channel scanning is necessary for the unit to memorize all  
available channels in your area.[Initial Setup] p.15  
side or rear of this unit  
Note  
org for further information.  
Depending on your antenna system, you may need different types of  
combiners (mixers) or separators (splitters). Contact your local electronics  
store for these items.  
For your safety and to avoid damage to this unit, please unplug the RF  
coaxial cable from the antenna input jack before moving the unit.  
If you use an antenna to receive analogTV, it should also work for DTV  
reception. Outdoor or attic antennas will be more effective than a set top  
or inside antenna.  
To switch your reception source easily between antenna and cable, install an  
antenna selector.  
If you are not receiving a signal from your cable service, contact the Cable  
provider.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
26MF330B  
External Device Connection  
satellite dish  
RF coaxial cable  
HDMI Connection  
ANT IN  
or  
HDMI connection offers the highest picture quality.  
HDMI (High-Denition Multimedia Interface) transports high denition  
video and multi-channel digital audio through a single cable.  
e.g.)  
STEREO  
PCM  
cable receiver/  
satellite box  
cableTV signal  
including PPV  
COMPONENT VIDEO OUT  
AUDIO OUT  
HDMI OUT  
Y
Pb/Cb  
Pr/Cr  
L
R
or  
32MF330B  
side or rear of this unit  
(red)  
(green) (blue)  
HDMI cable  
or  
or  
component video cables (red/  
blue/green) and audio cables  
or  
HDMI cable  
side or rear of  
this unit  
or  
HDMI OUT  
TITLE  
5
CHAPTER 15  
REPEAT A-B  
BD/DVD recorder  
with the HDMI output jack  
You can also connect this unit to the cable receiver or satellite box  
other than the HDMI or the component video output jacks because  
they might have different output jacks.  
26MF330B  
Required cables and connecting methods of the cable receiver/  
satellite box, or the availability channel for the clear QAM may differ  
depending on the cable/satellite provider. For more information,  
or  
HDMI cable  
please contact your cable/satellite provider.  
or  
side or rear of this unit  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
HDMI-DVI Connection  
ComponentVideo Connection  
Use an HDMI-DVI conversion cable to connect the unit to  
external video devices equipped with DVI output jack.  
ComponentVideo connection offers better picture quality for  
video devices connected to the unit.  
If you connect to the unit’s ComponentVideo Input jacks,  
connect audio cables to the Audio L/R Input jacks right beside  
the ComponentVideo connector.  
e.g.)  
32MF330B  
e.g.)  
To HDMI1  
Input jack only  
32MF330B  
rear of this unit  
DVI  
ANALOG  
AUDIO  
DVI  
rear of this unit  
ANALOG  
AUDIO  
HDMI-DVI  
conversion cable  
audio cables  
audio cables  
component video cables  
AUDIO OUT  
(red/blue/green)  
L
R
STEREO  
PCM  
cable receiver or satellite box  
with the DVI output jack  
COMPONENT VIDEO OUT  
AUDIO OUT  
Y
Pb/Cb  
Pr/Cr  
L
R
TITLE  
5
CHAPTER 15  
REPEAT A-B  
DVI OUT  
BD/DVD recorder with  
the component video output jack  
audio cables  
HDMI-DVI  
conversion cable  
component video  
cables  
(red/blue/green)  
audio cables  
To HDMI1  
Input jack only  
26MF330B  
4
.
2T  
2D  
;
rear of this unit  
rear of this unit  
Note  
The unit accepts 480i/480p/720p and 1080i of video signals for this  
connection.  
Note  
For HDMI connection  
The unit accepts 480i, 480p, 720p and 1080i of video signals, and 32kHz,  
44.1kHz and 48kHz of audio signals.  
S-Video Connection  
This unit accepts only 2 channel audio signal (LPCM).  
You need to select "PCM" for the digital audio of the device you connected  
or check the HDMI audio setting.There may be no audio output if you  
select "Bitstream", etc.  
S-Video connection offers good picture quality for video  
devices connected to the unit. If you connect to the unit’s  
S-Video Input jack, connect audio cables to the Audio L/R  
Input jacks right beside the CompositeVideo connector.  
This unit accepts only signals in compliance with EIA861.  
For HDMI-DVI connection  
The unit accepts 480i, 480p, 720p and 1080i video signals.  
HDMI-DVI connection requires separate audio connections as well and the  
audio signals are converted from digital to analog.  
DVI does not display 480i image which is not in compliance with EIA/  
CEA-861/861B.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
e.g.)  
Audio Output Connection  
32MF330B  
S-Video cable  
audio cables  
Digital (for digital broadcasting only)  
If you connect this unit to an external digital audio device,  
you can enjoy multi-channel audio like 5.1ch digital  
broadcasting sound.  
Use a digital audio coaxial cable to connect the unit to  
external digital audio devices.  
side of this unit  
Analog (for both analog and digital broadcasting)  
If you connect this unit to an external analog audio device,  
you can enjoy stereo (2-channel) audio.  
Use audio cables to connect the unit to external analog  
audio devices.  
S-VIDEO  
OUT  
AUDIO OUT  
L
R
TITLE  
5
CHAPTER 15  
REPEAT A-B  
BD/DVD recorder, camcorder  
andVCR with the S-Video output jack  
e.g.)  
32MF330B  
audio cables  
26MF330B  
rear of this unit  
audio cables  
S-Video cable  
side of this unit  
DVI  
ANALOG  
AUDIO  
CompositeVideo Connection  
digital audio  
coaxial cable  
CompositeVideo connection offers standard picture quality  
for video devices connected to the unit. If you connect to  
the unit’s CompositeVideo Input jack, connect audio cables  
to the Audio L/R Input jacks right beside the Composite  
Video connector.When the audio jack of the video device is  
monaural, connect an audio cable to the Audio L Input jack.  
DIGITAL AUDIO  
COAXIAL IN  
stereo system  
AUDIO IN  
L
R
e.g.)  
32MF330B  
video cable  
audio cables  
side of this unit  
Dolby Digital  
decoder  
audio cables  
rear of this unit  
digital audio  
coaxial cable  
AUDIO OUT  
VIDEO  
OUT  
L
R
R
L
P
camcorder  
video game  
26MF330B  
R -HDMI- L  
R
-
LINE OUT-  
L
COAXIAL  
STAND-BY  
STEREO  
VCR  
26MF330B  
side of this unit  
Note  
If you connect to the S-Video Input jack and the CompositeVideo Input  
jack at the same time, the S-Video connection will have priority.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
PC Connection  
Cable Management  
This unit can be connected to your PC that has a DVI terminal.  
Use an HDMI-DVI conversion cable for this connection and it  
requires stereo mini plug conversion cables as well.  
If you connect this unit to your PC, you can use this unit as a  
PC monitor.  
Keep the cables through this holder to avoid tangling them.  
rear of this unit  
e.g.)  
32MF330B  
To HDMI1  
Input jack only  
26MF330B  
rear of this unit  
DVI  
ANALOG  
AUDIO  
rear of this unit  
HDMI-DVI conversion  
cable  
stereo mini plug  
conversion cables  
DVI OUT  
Plug In the AC Power Cord  
Make sure that the AC power cord must be plugged to an  
AC outlet after all the necessary connections are completed.  
completed.  
personal computer  
HDMI-DVI conversion cable  
should be with ferrite core.  
rear of this unit  
32MF330B  
HDMI-DVI conversion cable  
26MF330B  
To HDMI1  
Input jack only  
AC outlet  
stereo mini plug  
conversion cables  
26MF330B  
rear of this unit  
rear of this unit  
The following video signals can be displayed:  
Format  
VGA  
Resolution  
640 480  
Refresh rate  
SVGA  
XGA  
800 600  
1 024 768  
1 280 768  
1 360 768  
60Hz  
AC power cord  
AC outlet  
WXGA  
Caution:  
Other formats or non-standard signals will not be displayed  
correctly.  
Do not connect the AC power cord to a power supply outside the  
indicated voltage of this unit (AC 120V).  
Note  
Connecting the AC power cord to a power supply outside of this range may  
result in re or electrical shocks.  
Please purchase the cable HDMI-DVI conversion cable that has a ferrite  
core.  
Note  
The following operations may reduce noise.  
- Attach a ferrite core to the AC power cord of your PC.  
Each time you plug in the AC power cord, no operations will be performed  
for a few seconds.This is not a malfunction.  
- Unplug the AC power cord and use the built-in battery of your PC.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
4
Use /to select the desired location setting, then  
These operations are accessible by remote control.  
Some may also be accessible by controls on the main unit.  
press OK  
Initial Setup  
Select “Retail” or “Home” for your location.  
Initial Setup  
This section will guide you through the unit’s initial setting  
which includes selecting a language for your on-screen menu  
and autoprogram, which automatically scans and memorizes  
viewable channels.  
Home  
Retail  
OK  
Select  
OK  
Before you begin:  
Make sure the unit is connected to antenna or cable.  
Select [Retail] store, the unit will be set up with  
predefined setting for retail displays. In this setting, the  
power consumption may possibly exceed the limited  
requirement of the ENERGY STAR® qualification.  
1 After making all the necessary connections,  
press to turn on the unit.  
• Select [Home], the unit is set to maximize the energy  
efficiency for home setting and it can be adjusted  
through a choice of picture and sound quality according  
to your preference.  
• When the initial setup is completed, the lowest  
memorized channel with the confirmation message of  
the location setting will be displayed on theTV screen.  
• It may take a few moments to turn on the unit for the  
first time.  
[Initial Setup] menu appears automatically after the  
unit is turned on.  
2 Use /to select the on-screen language from the  
choices (English/Español/Français) on the right side of the  
TV screen.  
Note  
If you are not receiving a signal from your cable service, contact the Cable  
provider.  
If you press or MENU during autoprogram, this setting will be canceled.  
The initial autoprogram function can be executed for either [Antenna] or  
[Cable] only once.When you change the connection (Antenna/Cable),  
3 Use /to select [Antenna] for TV channels or [Cable]  
for CATV channels, then press OK  
Initial Setup  
set [Autoprogram] again.  
p.19  
Make sure the antenna is connected to ''ANT. IN'' jack.  
Antenna  
If there is no signal input from the antenna terminal and no operation for  
several seconds after you turn on the unit, [Helpful Hints] appears. Follow  
the instructions listed on theTV screen.  
Select your signal source.  
Cable  
Skip  
Initial Setup  
Antenna  
Or  
Cable  
ANT.IN  
Retry  
No channel is registered.  
Try Autoprogram again?  
Later  
BACK  
MENU  
Verify that you have a cable connected to the "ANT. IN" jack on the back  
of the TV, the channel installation process searches this connection. If  
you are using a cable or satellite box, please confirm the input which  
you have connected the box and press "SOURCE" key on the remote  
control to select the appropriate source input.  
OK  
Select  
OK  
Back  
Skip  
[Autoprogram] will begin.  
MENU  
Initial Setup  
OK  
Select  
OK  
Skip  
Please wait while the system is scanning for channels. Auto programming  
may take more than 20 minutes to complete.  
You must set [Home] in step 4. Otherwise, the settings of picture and  
sound quality you adjusted will not be memorized after you turn off the  
unit.  
0%  
Digital channels  
Analog channels  
0 ch  
0 ch  
After an initial setup is completed...  
• If you want to scan the channels automatically again.  
MENU  
Skip  
[Autoprogram]  
p.19  
You can add the desired cable and analog channels  
unmemorized by autoprogram.  
[Add Channels]  
p.20  
• If you want to change to another language.  
[Language Selection] p.21  
• If you want to change the location setting.  
[Location]  
p.30  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
WATCHINGTV  
SleepTimer can be set to automatically turn off the unit after an incremental  
period of time.  
Press SLEEP repeatedly to change the amount of time (increases  
Sleep  
120min.  
the time by 30 minutes up to 120 minutes) until shut off.  
Press SLEEP once to call up the display for checking the remaining time.  
To cancel sleep timer, press SLEEP repeatedly until  
[Sleep Off] is displayed.  
Switching Each Input Mode can easily switch with the remote control  
betweenTV (ATSC or NTSC) and external devices when they are connected to the unit.  
Press SOURCE or
CH +
repeatedly to cycle through the input modes.  
Source  
e.g.)  
TV  
Video  
11.1  
DTV/TV channel  
Video  
Component  
Component  
HDMI1  
HDMI2  
HDMI3  
HDMI3  
HDMI2  
HDMI1  
(or PC input)  
Pressing CH reverses the direction of the input modes.  
can freeze the image shown on theTV screen for 5 minutes.  
Freeze Mode  
Press FREEZE to freeze the image.  
Freeze  
The sound output will not be paused.  
To cancel freeze mode, press any buttons except  
Channel Selection  
Select channels by using CH +/or the Number buttons  
To select the memorized channels,  
use CH +/or the Number buttons  
To select the non-memorized channels,  
use the Number buttons  
11.1  
To use the Number buttons  
ATSC  
-
When selecting digital channel 11.1  
.
Be sure to press before entering the subchannel number.  
NTSC  
-
When selecting cable or analog channel 11  
Press PREV CH to return to the previously viewed channel.  
[No Signal] will appear on theTV screen after the subchannel broadcast is over.  
[Audio only program] message will appear on the TV screen, when you receive  
only sound signal.  
Note  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
TV Screen Display Mode  
5 types of display modes can be selected when the broadcasting station is sending 16:9 or 4:3 video signal. And 3 types of display  
modes can be selected for PC input signal.  
Press FORMAT repeatedly to switch the TV aspect ratio.  
For 16:9 video signal  
Normal displays a 16:9 picture at its original size.  
4:3 displays a 16:9 picture at a 4:3 size; the picture  
is shortened horizontally. Sidebars appear on both  
edges of the screen.  
Movie Expand displays a 16:9 picture that is  
vertically stretched to ll the screen. This only crops  
out the top of the picture.  
Normal  
4:3  
Movie Expand  
Zoom displays a 16:9 picture at its maximum size  
without changing its horizontal and vertical ratio.  
Wide displays a horizontally stretched picture.This  
crops out the left and right sides of the picture.  
Wide  
Zoom  
Normal displays a 4:3 picture at its original size.  
Sidebars appear on both edges of the screen.  
For 4:3 video signal  
16:9 displays a 4:3 picture at a 16:9 size; the picture is  
stretched horizontally to ll the screen.  
Movie Expand displays a 4:3 picture at a 16:9 size;  
the picture is stretched more vertically at the top of  
the screen. This crops out the top of the picture.  
Normal  
16:9  
Movie Expand  
Zoom displays a 4:3 picture at a 16:9 size; at its  
maximum size that is more vertically stretched to ll  
the screen.This crops out the top and bottom of the  
picture.  
Wide  
Zoom  
Wide displays the picture with its center at the  
original size and the edges stretched horizontally to  
ll the screen.  
Normal displays a proportionately stretched picture.  
Sidebars appear on both edges of the screen.  
HDMI1  
For PC input signal through  
Input mode  
Full displays a picture that is stretched out of  
proportion horizontally to ll the screen.  
Dot By Dot displays a picture in its original size.  
Normal  
Full  
Dot By Dot  
Sound Functions  
describe how to change the audio or the audio language as well as the volume.  
Volume Adjustment  
Use VOL +/to adjust the volume.  
Volume  
30  
will be displayed for a few  
Silence Mode  
seconds when adjusting the volume.  
Press MUTE to turn off the sound temporarily.  
Mute  
will be displayed for a few seconds.  
Press MUTE again or VOL +/to recover the  
original volume.  
Switching Audio Mode  
ATSC  
NTSC  
Press SAP repeatedly to cycle through the available  
audio languages.  
Press SAP to display the currently selected audio mode.  
While receiving an MTS broadcast, press repeatedly to cycle through the  
available audio channel.  
Available languages differ depending on the  
broadcast.  
[Other] is displayed when the audio language  
cannot be acquired, or the acquired languages are  
other than English, Spanish or French.  
11  
SAP/STEREO  
e.g.) When all audio are available  
SAP/STEREO  
SAP/MONO  
SAP/STEREO  
11.1  
English 1/3  
STEREO : Outputs stereo-audio  
SAP  
: Outputs second audio program  
MONO : Outputs mono-audio  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
TV Screen Information  
Reducing the Brightness  
You can display the currently selected channel or other  
information such as the audio mode on the TV screen.  
In the digital mode, the detailed broadcasting information for  
the current channel such as program title, program guides are  
displayed.  
Backlight brightness can be reduced which may save on power  
consumption more than you just set [On] in [Energy Saving  
Mode]. p.30  
Press ECO once to reduce the brightness.  
Press ECO again to increase the brightness.  
Press INFO  
Note  
Even if this function is in effect, the brightness will be increased when you  
change [Energy Saving Mode] on or off due to the energy saving mode has  
priority.  
ATSC  
You must set [Home] in [Location]  
Otherwise, the settings you adjusted will not be memorized after you turn  
off the unit.  
p.30  
1
2
3
4
A Day of Memories  
KABC  
11.1  
English 1/2  
5
A quarter-century ago,which may now qualify as the  
good old days of newspapering,run-of-paper sales  
accounted for 80 percent of the industry's advertising  
revenues.Department stores and supermarket were  
1080i HD  
16:9  
6, 7, 8  
CC  
Rating  
TV: TV-14  
9
10  
Fun-Link Options  
NTSC  
If you have our brand products such as BD player or DVD  
recorder that are compatible with Fun-Link functions, connect  
them to this unit via an HDMI cable so you can simply operate  
various items from this unit's remote control.  
4
SAP/STEREO  
5
6, 7, 8  
9
10  
Before you begin:  
You must set [On] in [Device Control] and  
[Fun-Link Control]  
p.29  
Otherwise, FUN-LINK OPTIONS  
you connected our brand devices to this unit.  
does not work even if  
1 program title  
2 program guide  
(The program guide added to broadcasting  
information is displayed to a maximum of 4 lines.)  
3 broadcast station  
4 channel number  
5 audio language (ATSC)/audio mode (NTSC)  
[Switching Audio Mode]  
6 effective scanning lines and scan mode  
7 TV format  
To enjoy Fun-Link, verified and recommended devices  
are as follows;  
MAGNAVOX  
NB530MGX  
NB500MG1F  
MBP1100/F7  
SYLVANIA  
NB530SLX  
NB500SL1  
p.17  
1
Press FUN-LINK OPTIONS  
to display  
8 program aspect ratio  
9 CC (not available if closed caption is set to [Off])  
10child lock rating  
[Fun
-
Link Options] menu  
Fun-Link Options  
Device-menu  
Device-contents  
Device-favorite  
To clear the display, press INFO again.  
You can also press BACK  
.
Note  
This function allows you to control  
the menu of your connected Fun-Link  
device.  
Device-menu  
When the program guide consists of more than 4 lines, use /to scroll.  
[No description provided.] is displayed when the program guide is not  
provided.  
This function allows you to control the  
top menu of your DVD or Blu-ray discs.  
Device-contents  
Device-favorite  
While the program guide is displayed, the closed caption function is  
interrupted.  
In external input mode, the following screen is displayed;  
e.g.) When an external device is connected toVideo Input jack.  
This function allows you to control the  
pop-up menu of your Blu-ray discs.  
2
Use ////OK on this unit's remote control to  
Video  
480i SD  
operate the desired functions for your devices.  
CC  
TV-PG DLSV  
Note  
Some of Fun-Link functions may not be available depending on your Fun-  
Link devices or discs.  
The information display will automatically disappear in 1 minute.  
We do not guarantee 100% interoperability with other brands of HDMI link  
compliant devices.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
Autoprogram  
OPTIONAL SETTING  
If you switch wires (e.g. between antenna and CATV) or if you  
move the unit to a different area after the initial setting, or if  
you restore the DTV channels you deleted, it is recommended  
to use Autoprogram to perform a new channel search.  
Main Menu  
This section describes the overview of the main menu  
displayed when you press MENU. The main menu consists of  
the function setting items below.  
Before you begin:  
Make sure the unit is connected to antenna or cable.  
1
Press MENU to display the main menu.  
Picture  
2 Use /to select [Setup], then press OK  
3
Use /to select [Autoprogram], then press OK  
4
Use /to select an appropriate option, then press OK  
Sound  
Press MENU  
Setup  
Features  
Language  
Back  
Picture  
Sound  
Autoprogram will rescan all channels.  
Auto programming may take more than 20  
minutes to complete.  
Antenna  
Cable  
Picture [Picture Adjustment]  
p.22  
p.22  
p.19  
Setup  
Select your signal source.  
Sound  
Setup  
[Sound Adjustment]  
[Autoprogram]  
Features  
Language  
Antenna  
You can automatically scan the viewable channels.  
[Channel List] p.20  
Or  
Cable  
ANT.IN  
The Channels that were autoprogrammed are in  
this Channel list,use CH
+/
to access them.  
When connected toVHF/UHF antenna,  
[Add Channels]  
p.20  
select [Antenna]  
• When connected to CATV, select [Cable]  
[Autoprogram] will begin.  
You can add TV channels that were not found by  
the autoprogram scan.  
Features [Closed Caption]  
p.24  
You can change the display closed caption format  
which displays the dialogue of aTV program or  
other text information across theT
V screen.  
Please wait while the system is scanning for channels. Auto programming  
may take more than 20 minutes to complete.  
75%  
[Child Lock]  
p.27  
You can set viewing limitations.  
[Fun-Link]  
Digital channels  
10 ch  
p.29  
Analog channels  
6 ch  
You can set Fun-Link options.  
[Energy Saving Mode]  
[Location]  
MENU  
Exit  
p.30  
p.30  
• When the scanning and memorizing are completed, the  
lowest memorized channel will be displayed.  
Switch setting from [Retail] to [Home] to allow the  
desired [Picture] and [Sound] mode to be kept in  
memory.  
Note  
After setting [Autoprogram], using CH +/
on the remote control skips  
unavailable programs automatically.  
If you are not receiving a signal from your cable service, contact the Cable  
provider.  
If you press or MENU during autoprogram, the setting will be canceled.  
Even if [Autoprogram] is completed, the channel setting will be lost if the  
AC power cord is unplugged before turning off the unit by pressing  
The PIN code will be required once you set a PIN code in the [Child Lock]  
[Current Software Info]  
p.30  
p.21  
Language [Language Selection]  
Change the Main Menu language.  
p.27  
If you want to change your PIN code, follow the instruction of  
[Change PIN]  
p 28  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Channel List  
Add Channels  
The channels selected here can be skipped when selecting the  
channels using CH +/  
Those channels can still be selected with the Number buttons  
This function lets you add the channels that were not added  
by the autoprogram due to reception conditions at the initial  
setting.  
1
Press MENU to display the main menu.  
1
Press MENU to display the main menu.  
2 Use /to select [Setup], then press OK  
3 Use /to select [Channel List], then press OK  
2 Use /to select [Setup], then press OK  
3 Use /to select [Add Channels], then press OK  
4 Use /to select the channel you want to remove, then  
4 Use the Number buttons to enter the number of the  
press OK  
channel you want to add, then press OK  
11  
DTV  
DTV  
DTV  
11.1  
11.2  
11.3  
Picture  
Sound  
Setup  
Highlight channels for Ch Up/Down key selection.  
Add channels  
Picture  
Sound  
Features  
Language  
For analog channels, select a channel to be  
added using number keys.  
Setup  
For digital channels, you must perform  
Autoprogram function.  
Features  
Language  
BACK  
OK  
Ch Select  
Watch/Skip  
Back  
• The channel display for the removed channel darkens.  
You will not be able to select the channel again using  
CH +/  
BACK  
Ch Change  
Back  
To reactivate a removed channel, use /and press  
OK.The registered channels are highlighted.  
5 Press MENU to exit.  
• When you remove a main channel, its subchannels are  
removed as well.  
Note  
If setup completes successfully, [Added to the channel list] is displayed.  
If external input is used, it is not possible to register the channel and  
[Unavailable] will be displayed on theTV screen.  
5 Press MENU to exit.  
By using CH +
/–
, you can select the memorized channels only.  
Note  
The channel with the [DTV] indicated on the display is ATSC.  
Otherwise the channel is NTSC.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
Antenna Conrmation  
ATSC  
Language Selection  
You can choose English, Spanish, or French as your on-screen  
language.  
This function lets you check the digital signal strength of each  
channel.  
1 Press MENU to display the main menu.  
1
Press MENU to display the main menu.  
2 Use /to select [Setup], then press OK  
3 Use /to select [Antenna], then press OK  
2 Use /to select [Language], then press OK  
3 Use /to select [English] [Español] or [Français], then  
press OK  
4 Use the Number buttons or CH +/ to select the  
channel for which you want to check the digital signal  
strength.  
Picture  
Select your menu language.  
English  
Español  
Français  
Sound  
Setup  
11.1  
Seleccione el idioma para el menú.  
Sélectionnez la langue du menu.  
Features  
Language  
Back  
Picture  
Sound  
Setup  
Features  
Language  
4 Press MENU to exit.  
Current 50 Max  
50  
Note  
If you need the English menus instead of the Spanish or French menus, press  
MENU. Use /to select [Idioma] or [Langue], then press OK  
Use /to select [English], then press OK  
CH  
Ch Change  
Press MENU to exit the main menu.  
• If the channel is set to analog (cable) channel or  
external input, you cannot confirm the antenna  
condition.  
Video  
Back  
Picture  
Sound  
Setup  
Indicator is available for digital  
broadcasting only.  
Features  
Language  
CH  
Ch Change  
5 Press MENU to exit.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Brightness, Contrast, Color, Tint,  
Sharpness, ColorTemperature  
Picture Adjustment  
You can adjust picture mode, or customize the picture quality  
as your preference.  
You can only adjust the following options when you set  
to [Personal]
in
[Smart Picture]. Use /to select the  
desired setting, then use /to adjust.  
Before you begin:  
You must set [Home] in [Location]  
Otherwise, the settings you adjusted will not be memorized  
after you turn off the unit.  
p.30  
Brightness  
Press  
to increase  
brightness  
Brightness  
30  
to decrease  
brightness  
OK  
OK  
OK  
OK  
OK  
OK  
Adjust  
Move  
Move  
Move  
Move  
Move  
OK  
OK  
OK  
OK  
OK  
OK  
1 Press MENU to display the main menu.  
Contrast  
Press ◄  
to decrease  
contrast  
Press ►  
to increase  
contrast  
Contrast  
60  
2 Use /to select [Picture], then press OK  
Adjust  
Color  
3 Use /to select the item you want to adjust, then press  
Press ◄  
to decrease  
color intensity color intensity  
Press ►  
to increase  
Color  
36  
OK  
Adjust  
Tint  
Press ►  
to add green  
Smart Picture  
Brightness  
Contrast  
Personal  
Picture  
Sound  
Tint  
0
to add red  
30  
60  
36  
0
Adjust  
Setup  
Color  
Features  
Language  
Sharpness  
Press ◄  
to soften  
Press ►  
to sharpen  
Tint  
Sharpness  
0
Sharpness  
Color Temperature  
0
Adjust  
Normal  
ColorTemperature  
to add warm  
colors  
Press ►  
to add cool  
colors  
Color Temp. Normal  
Adjust  
Move  
4 Adjust the following items.  
Smart Picture  
5 Press MENU to exit.  
Use /to select the desired setting, then press OK  
([Personal] [Standard] [Sports] [Movie], and [Game])  
Sound Adjustment  
You can adjust the sound mode, equalizer and some other  
Personal  
Standard  
Sports  
Picture  
Sound  
Smart Picture  
Brightness  
Contrast  
sound functions.  
Setup  
Color  
Movie  
Features  
Language  
Before you begin:  
Tint  
Game  
You must set [Home] in [Location]  
p.30  
Sharpness  
Color Temperature  
Otherwise, the settings you adjusted will not be memorized  
after you turn off the unit.  
1 Press MENU to display the main menu.  
2 Use /to select [Sound], then press OK  
3 Use /to select the item you want to adjust, then press  
OK  
Smart Sound  
Standard  
Picture  
Sound  
Equalizer  
Virtual Surround Sound  
Auto Volume Leveling  
TV Speakers  
On  
Setup  
Off  
Features  
Language  
Ext. Amp  
Stereo  
Primary MTS  
4 Adjust the following items.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
Smart Sound  
Use /to select the desired setting, then press OK  
([Personal] [Standard] [Movie] [Music], and [News])  
Reduces volume differences between the  
TV commercials and the programs.  
On  
Off  
Removes the auto volume leveling.  
TV Speakers  
Smart Sound  
Personal  
Standard  
Movie  
Picture  
Sound  
Select the audio output from the unit’s speakers, or not.  
If your amplier is HDMI link function compatible and  
connected by an HDMI cable to this unit, some sound  
operations such as volume up can be changed by using  
this unit’s remote control. Make sure [Fun-Link Control]  
Equalizer  
Virtual Surround Sound  
Auto Volume Leveling  
TV Speakers  
Setup  
Music  
Features  
Language  
News  
Primary MTS  
is set to [On]  
p.29  
Use /to select the desired option, then press OK  
Equalizer  
On  
Picture  
Sound  
Adjust tonal quality for each frequencies. Use /to  
select the specic frequency and use /to adjust the  
level, then press OK  
"
On":  
Off  
Sound will be output from the TV  
speakers.  
"Off":  
Sound will not be output from the TV  
speakers.  
"Ext. Amp":  
Ext. Amp  
Setup  
Features  
Language  
Operation is possible by connecting to the  
HDMI-CEC compatible amp with a  
HDMI cable.  
Picture  
0
0
0
0
0
Sound  
For details look in the user manual.  
Setup  
Features  
Language  
The sound will be output from the unit’s  
speakers.  
On  
The sound will not be output from the  
unit’s speakers.  
Off  
120Hz 500Hz 1.5kHz 5kHz 10kHz  
You can control audio output from your  
connected HDMI link devices by using this  
unit's remote control.  
Ext. Amp  
Virtual Surround Sound  
Virtual surround sound gives you the stereo phonic virtual  
space through your existing 2-channel stereo system. Use  
/to select the desired option, then press OK
.  
Note  
We do not guarantee 100% interoperability with other brands of HDMI  
link compliant devices.  
On  
Picture  
Sound  
Primary MTS  
Off  
You can set the output mode as a default for the sound  
mode (NTSC only).  
This setting is not interlocked when you change the  
This selects the modes for more spatial or  
surround sound reproduction.  
Setup  
Features  
Language  
output mode by pressing SAP [Sound Functions] p.17  
Use /to select the desired option, then press OK  
Smart Sound  
Picture  
Sound  
On  
Off  
Emphasized effect.  
Natural effect.  
Equalizer  
Virtual Surround Sound  
Auto Volume Leveling  
TV Speakers  
Setup  
Features  
Language  
AutoVolume Leveling  
Stereo  
Mono  
SAP  
Primary MTS  
This function keeps a constant loudness differential  
between theTV commercials and the programs.  
Use /to select the desired option, then press OK  
Stereo  
Mono  
SAP  
Outputs stereo-audio.  
Outputs mono-audio.  
On  
Picture  
Sound  
Off  
Auto Volume Leveling reduces volume  
differences between channels and  
programs, providing a consistent audio  
level.  
Outputs second audio program.  
Setup  
Features  
Language  
5
Press MENU to exit.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Closed Caption  
A. Captiioon SSeerrvice  
You can view closed captioning (CC) for TV programs,  
movies and news. Closed caption refers to text of dialogue or  
descriptions displayed on-screen.  
1
Press MENU to display the main menu.  
4 Use /to select [Caption Service], then press OK
.  
2 Use /to select [Features], then press OK  
5
Use /to select the desired closed caption, then press  
OK  
3
Use /to select [Closed Caption], then press OK  
See the following description for setting each item.  
Off  
Picture  
Sound  
Caption Service  
Digital Caption Service  
Caption Style  
CC-1  
CC-2  
CC-3  
CC-4  
T-1  
Caption Service  
Digital Caption Service  
Caption Style  
Off  
Off  
Picture  
Sound  
A
B
C
Setup  
Features  
Language  
Setup  
Features  
Language  
T-2  
T-3  
T-4  
The primary caption and text services.The  
captioning or text is displayed in the same  
language as the program’s dialogue (up to  
4 lines of script on theTV screen, where  
it does not obstruct relevant parts of the  
picture).  
CC-1 andT-1  
CC-3 andT-3  
Serve as the preferred data channels.  
The captioning or text is often a secondary  
language.  
Rarely available and broadcasters use them  
only in special conditions, such as when  
[CC-1] and [CC-3] or [T- 1 ] and [T- 3 ] are  
not available.  
CC-2, CC-4,  
T-2 andT-4  
• There are 3 display modes according to programs:  
Displays input characters on theTV screen  
immediately.  
Paint-on mode  
Once characters are stored in memory,  
Pop-on mode  
they are displayed all at once.  
Displays the characters continuously by  
Roll-up mode  
scrolling (max. 4 lines).  
6
Press MENU to exit.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
B. Digital Cappttiioonn SSeerrviiccee  
C. Caption Style  
ATSC  
ATSC  
In addition to the basic closed caption, DTV has its own closed  
caption called digital caption service. Use this menu to change  
the settings for digital caption service.  
You can change the caption style such as font, color or size,  
etc.  
4
Use /to select [Caption Style], then press OK  
4
Use /to select [Digital Caption Service], then press  
OK  
5
Use /to select [User Setting], then press OK  
5 Use /to select the desired digital caption service, then  
press OK  
User Setting  
Font Style  
Off  
Picture  
Sound  
Font0  
Middle  
White  
Solid  
Black  
Solid  
Black  
None  
Font Size  
Setup  
Off  
Picture  
Sound  
Caption Service  
Digital Caption Service  
Caption Style  
Font Color  
Features  
Language  
CS-1  
CS-2  
CS-3  
CS-4  
CS-5  
CS-6  
Font Opacity  
Background Color  
Background Opacity  
Edge Color  
Setup  
Features  
Language  
Edge Type  
6 Use /to select [On], then press OK
.  
7
Use /to select an item, then press OK. Then use  
Select if you do not want digital caption  
service.  
Off  
/to select the desired setting and press OK  
Select one of these before changing  
any other item in [Closed Caption]  
menu. Choose [CS-1] under normal  
circumstances.  
Picture display  
CS-1 to CS-6  
So, you must be Philip. Hi!  
I’m pleeased tto mmeeeett you.  
6 Press MENU to exit.  
Edge  
Note  
(Edge Color and EdgeType)  
Font  
[Digital Caption Service] that you can switch differs depending on the  
broadcast description.  
(Font Style, Font Size, Font Color and Font Opacity  
orTransparency)  
Background  
(Background Color and Background Opacity or  
Transparency)  
• The setting description for each item is shown on the  
next page.  
• Review your setting choice made on the next page  
by looking in the upper right corner of the displayed  
setting box (not all selections show the differences  
selected).  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Font Style  
Closed Captioning font style  
can be changed as illustrated.  
Background Opacity  
Background opacity of the  
displayed caption can be  
switched as illustrated.  
Closed Caption  
Closed Caption  
Solid  
Flash  
Translucent  
Transparent  
Font Size  
Edge Color  
Closed Caption  
Closed Caption  
Font size of the displayed  
caption can be switched as  
illustrated.  
Edge color of the displayed  
caption can be switched as  
illustrated.  
White  
Black  
Red  
Large  
Middle  
Small  
Green  
Blue  
Yellow  
Magenta  
Cyan  
Font Color  
EdgeType  
Closed Caption  
Closed Caption  
Font color of the displayed  
caption can be switched as  
illustrated.  
Edge type of the displayed  
caption can be switched as  
illustrated.  
White  
Black  
Red  
None  
Raised  
Green  
Blue  
Depressed  
Uniform  
Yellow  
Magenta  
Cyan  
L. Shadow  
R.Shadow  
Font Opacity  
Closed Caption  
8 Press MENU to exit.  
Font opacity of the displayed  
caption can be switched as  
illustrated.  
Note  
Closed caption will not be displayed when you are using an HDMI  
connection.  
To show the closed caption on yourTV screen, broadcast signal must  
contain the closed caption data.  
Not allTV programs and commercials have the closed caption or all types  
of the closed caption.  
Solid  
Flash  
Translucent  
Transparent  
Captions and texts may not exactly match theTV voice.  
Changing channels may delay the closed caption for a few seconds.  
Adjusting or muting the volume may delay the closed caption for a few  
seconds.  
Abbreviations, symbols and other grammatical shortcuts may be used in  
order to keep pace with the on-screen action.This is not a malfunction.  
The caption or text characters will not be displayed while the main menu  
or functions display is shown.  
Background Color  
Background color of the  
displayed caption can be  
switched as illustrated.  
Closed Caption  
White  
Black  
Red  
If a black box appears on theTV screen, this means that the closed caption  
is set to the text mode.To clear the box, select [CC-1] [CC-2] [CC-3]  
[CC-4] or [Off]  
Green  
Blue  
If the unit receives poor quality television signals, the captions may contain  
errors, or there might be no captions at all. Some possible causes of poor  
quality signals are:  
Yellow  
Magenta  
Cyan  
- Automobile ignition noise  
- Electric motor noise  
- Weak signal reception  
- Multiplex signal reception (ghosts or screen utter)  
-
Data dropout and Pixelation (for DTV only)  
The unit retains the closed caption setting if the power fails.  
When the unit receives special effects playback signal (e.g. Search, Slow  
and Still) from aVCR’s video output channel (ch3 or ch4), the unit may not  
display the correct caption or text.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
Child Lock  
A. Channel Lock  
Child lock reads the ratings for programs, then denies access  
to the programs which exceed the rating level you set. With  
this function, you can block certain programs inappropriate  
for children and any channels or external input modes can be  
invisible.  
Particular channels or external input modes can be invisible in  
this function.  
5 Use /to select [Channel Lock], then press OK  
6 Use /to select the desired rating, then press OK  
1 Press MENU to display the main menu.  
repeatedly to switch between [View]
and
[Block]
.  
2 Use /to select [Features], then press OK  
3 Use /to select [Child Lock], then press OK  
Picture  
Video  
Sound  
Component  
Setup  
HDMI 1  
Features  
Closed Caption  
Child Lock  
Picture  
Sound  
HDMI 2  
Language  
HDMI 3  
Fun-Link  
Setup  
40.1 DTV  
Energy Saving Mode  
Location  
On  
Features  
Language  
Home  
BACK  
OK  
Select  
View / Block  
Back  
Current Software Info  
7 Press MENU to exit.  
4 Use the Number buttons to enter the 4-digit numbers for  
your PIN code.  
Features  
Enter PIN.  
_
Language  
B. Setting US Movie ratiinnggss  
• When you have not set up your PIN code,  
US Movie ratings lock is the rating system created by MPAA.  
enter 0 0 0 0  
• When the PIN code is correct, [Child Lock] menu is  
displayed.  
5 Use /to select [US Movie Ratings Lock], then press  
See the following description for setting each item.  
OK  
6 Use /to select the desired rating, then press OK  
Channel Lock  
Picture  
A
B
repeatedly to switch between [View] and [Block]  
US Movie Ratings Lock  
Sound  
US TV Ratings Lock  
Setup  
C
Canadian English Rating  
Canadian French Rating  
Region Ratings Lock  
Change PIN  
Features  
Language  
Picture  
X
Sound  
NC-17  
D
Setup  
R
Features  
PG-13  
Language  
PG  
G
Note  
NR  
When you select a rating and set it to [Block], the higher ratings will be  
blocked automatically.The lower ratings will be available for viewing.  
When you set the highest rating to [View], all ratings turn to [View]  
automatically.  
To block any inappropriate programs, set your limits in [US Movie Ratings  
Lock] [USTV Ratings Lock] and [Region Ratings Lock]  
BACK  
OK  
Select  
View / Block  
Back  
Rating  
Category  
X
Mature audience only  
The child lock setting will be retained after a power failure (except the PIN  
code reverts to 0000).  
NC-17  
No one under 17 admitted  
Restricted; under 17 requires accompanying  
parent or adult guardian  
If the rating is blocked, will appear.  
[Region Ratings Lock] will be available when the unit receives a digital  
broadcast using the new rating system.  
For the United States, the unit may download the Region Ratings LockTable,  
if required.  
The Canadian rating systems on this unit are based on CEA-766-A and  
CRTC policy.  
R
PG-13  
PG  
Unsuitable for children under 13  
Parental guidance suggested  
General audience  
G
NR  
No rating  
7 Press MENU to exit.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
C. SettingTV ratings  
D. Change PIINN  
Although the default PIN code (0000) is supplied with the unit,  
you can set your own PIN code.  
5 Use /to select [USTV Ratings Lock], then press OK  
6 Use ///to select the desired rating, then press  
OK repeatedly to switch between [View] and [Block]  
5 Use /to select [Change PIN], then press OK  
6 Press the Number buttons to enter the new 4-digit PIN  
Picture  
code.  
FV  
V
S
L
D
Sound  
TV-MA  
TV-14  
TV-PG  
TV-G  
• Enter PIN code again in [Confirm PIN.] entry field.  
Setup  
Features  
Language  
Picture  
Sound  
TV-Y7  
TV-Y  
Enter PIN.  
_
Setup  
BACK  
OK  
Select  
View / Block  
Back  
Features  
Language  
Confirm PIN.  
Rating  
Category  
TV-MA  
Mature audience only  
higher  
lower  
BACK  
TV-14  
TV-PG  
TV-G  
Unsuitable for children under 14  
Parental guidance suggested  
General audience  
PIN Code  
Back  
7 Press MENU to exit.  
Appropriate for all children 7 and  
older  
TV-Y7  
TV-Y  
Note  
Make sure new PIN code and conrm PIN code must be exactly the same.  
If they are different, the space is cleared for reentering.  
Appropriate for all children  
Your PIN code will be erased and return to the default (0000) when a  
power failure occurs.  
If you forget the PIN code, unplug the AC power cord while turning the unit  
on, wait for 10 seconds to plug the AC power cord again.  
The unit will restore the PIN code to 0000 as the factory default.  
7 Press MENU to exit.  
To set the sub ratings  
As forTV-MA,TV-14,TV-PG, orTV-Y7, you can further set  
the sub ratings to block specic elements of programming.  
To set the sub ratings, follow the step below.  
Use ///to select the desired rating, then press  
OK repeatedly to switch between [View] and [Block]  
Picture  
Sound  
FV  
V
S
L
D
TV-MA  
TV-14  
TV-PG  
TV-G  
Setup  
Features  
Language  
TV-Y7  
TV-Y  
BACK  
OK  
Select  
View / Block  
Back  
Sub Rating  
Category  
FantasyViolence  
Rating  
FV  
V
TV-Y7  
Violence  
TV-MA  
TV-14  
TV-PG  
S
Sexual Situation  
Coarse Language  
Suggestive Dialogue  
L
D
TV-14,TV-PG  
Note  
Blocked sub rating will appear beside the main rating category in  
[USTV Ratings Lock] menu.  
You cannot block a sub rating (D, L, S orV) if the main rating is set to  
[View]  
Changing the category to [Block] or [View] automatically changes all its sub  
ratings to the same ([Block] or [View]).  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
AutoTV On  
This unit will turn on detected when the power on signal  
is sent from your connected Fun-Link device.  
Fun-Link  
This function allows you to operate the linked functions  
between our brand devices with a Fun-Link feature and this  
unit connecting through an HDMI cable.  
Use /to select the desired setting, then press OK  
1 Press MENU to display the main menu.  
On  
Picture  
Sound  
Off  
2 Use /to select [Features], then press OK  
3 Use /to select [Fun-Link], then press OK  
When set to "On", TV and connected device  
are turned on automatically.  
Setup  
Features  
Language  
Fun-Link Control  
Auto Device Off  
Auto TV On  
On  
On  
On  
On  
Picture  
Sound  
Setup  
This unit turns on automatically when you turn on  
your connected Fun-Link device.  
Device Control  
Device List  
Features  
Language  
On  
Off  
This unit stays off even if you turn on your  
connected Fun-Link device.  
Device Control  
You can operate some functions such as disc playback or  
call up the menu of the connected devices, by using this  
unit’s remote control.  
4 Use /to select the desired setting, then press OK
.  
5 Adjust the following items.  
Use /to select the desired setting, then press OK  
Fun-Link Control  
Set the Fun-Link [On] or [Off]  
The following additional settings will be in gray when you  
set to [Off]  
On  
Picture  
Sound  
Off  
When set to "On", the connected device is  
controlled using the remote control.  
Setup  
Use /to select the desired setting, then press OK  
Features  
Language  
On  
Picture  
Sound  
Off  
When set to "On", Fun-Link functions are  
enabled.  
Setup  
Features  
Language  
PLAY B/STOP C/FWD D/REV E/SKIP G/  
SKIP H/PAUSE F/FUN-LINK OPTIONS  
////OK/BACK /the Number  
buttons/RED/GREEN/BLUE/YELLOW can be  
used to control your connected Fun-Link devices by  
this unit's remote control  
/
On  
Off  
Disables the device control.  
Selects if you have connected an external device  
that is compatible with the Fun-Link function.  
On  
Off  
Device List  
Disables all Fun-Link.  
This function lets you see the product model number or  
name of connected devices.  
Auto Device Off  
You can set your device to turn off by interlocking from  
this unit’s power.  
Use /to select the desired HDMI device listed on  
theTV screen, then press OK.  
Use /to select the desired setting, then press OK  
Picture  
On  
Picture  
Sound  
HDMI1  
HDMI2  
NB530MGX  
Sound  
Off  
MBP1100 / F7  
Setup  
When set to "On" and TV is turned off,  
connected devices are turned off  
automatically.  
Setup  
Features  
Language  
Features  
Language  
BACK  
OK  
Select  
Input Change  
Back  
Your connected Fun-Link device turns off  
automatically when you turn off the unit.  
6 Press MENU to exit.  
On  
Off  
Your connected Fun-Link device stays on even if  
you turn off the unit.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Energy Saving Mode  
Current Software Info  
You can set whether the power consumption is saved or not.  
This function shows what version of the software currently  
used.  
1 Press MENU to display the main menu.  
1 Press MENU to display the main menu.  
2 Use /to select [Features], then press OK  
3
Use /to select [Energy Saving Mode], then press OK  
4
Use /to select the desired mode, then press OK  
2 Use /to select [Features], then press OK  
3
Use /to select [Current Software Info], then press  
OK  
4
Conrm the version of the software currently used.  
On  
Picture  
Sound  
Off  
Setup  
Back  
When set to “On”, power consumption is reduced  
by decreasing backlight brightness.  
Features  
Language  
Sound  
Setup  
Release Version:  
XXXXXXX_XXX_X_XXXX  
Features  
Language  
On  
Off  
Reduces the power consumption.  
The power consumption may possibly  
exceed the limited requirement of the  
ENERGY STAR® qualification.  
5
Press MENU to exit.  
5
Press MENU to exit.  
Location  
When you select [Retail] store, the power consumption may  
possibly exceed the limited requirement of the  
ENERGY STAR® qualication.  
1 Press MENU to display the main menu.  
2 Use /to select [Features], then press OK  
3
Use /to select [Location], then press OK  
4
Use /to select the desired location, then press OK  
Retail  
Home  
Sound  
Location Home is recommended for  
normal home use.  
In the Retail Store mode, all settings are  
fixed.  
Setup  
Features  
Language  
5
Press MENU to exit.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
TROUBLESHOOTING  
FAQ  
Question  
Answer  
Check the antenna or cable connection to the main unit.  
Check the batteries of the remote control.  
Check if there is an obstacle between the infrared sensor window and the remote  
control.  
Test the signal output. If OK, then possible infrared sensor trouble.  
My remote control does not  
work.  
What should I do?  
[IR Signal Check]  
p.34  
Aim the remote control directly at the infrared sensor window on the front of the unit.  
Reduce the distance to the unit.  
Re-insert the batteries with their polarities (+/– signs) as indicated.  
When there is an infrared-equipped device such as PC near this unit, it may interrupt  
the remote control signal of this unit.  
Move the infrared-equipped device away from this unit, change the angle of the infrared  
sensor or turn off the infrared communication function.  
How come the Initial setup  
appears every time I turn on  
this unit?  
Connect the RF coaxial cable to the unit directly and run the initial setup.  
Make sure to complete the channel scan before turning off the unit.  
Make sure [Autoprogram] has been completed.  
p.19  
Autoprogram must be completed when you set up the unit for the rst time or move it  
to a location where previously unavailable channels are broadcast.  
The selected channel may not be broadcasting.  
When [Autoprogram] is interrupted and not completed, some channels will not be  
Why I cannot watch some RF  
signalTV programs.  
received. Make sure to complete.  
p.19  
The selected channel cannot be viewed by the [Child Lock] setting.  
p.27  
The unit requires some kind of antenna input.An indoor antenna  
(VHF /UHF), an external antenna (VHF /UHF) or an RF coaxial cable from your wall  
cable/satellite box needs to be plugged into the unit.  
Check if the right input mode is selected by pressing SOURCE or using CH +/  
[Switching Each Input Mode]  
p.16  
How come there is no image  
from the connected external  
devices?  
Check the antenna or cable connection to the unit.  
When using the ComponentVideo Connection check that the Green (Y), Blue (Pb/Cb)  
and Red (Pr/Cr) connectors are connected to their corresponding colored jacks on the  
unit.  
Many digital channels have alternate channel numbers.  
The unit changes the numbers automatically to the ones signifying the broadcasting  
station channel number.  
Whenever I entered channel  
number,it changes automatically.  
These basic numbers used for previous analog broadcasts.  
(e.g., input ch#30 auto change to ch#6.1)  
Captions that are delayed a few seconds behind the actual dialogue are common for live  
broadcasts. Most captioning production companies can display a dialogue to maximum  
of 220 words per minute. If a dialogue exceeds that rate, selective editing is used to  
insure that the captions remain up-to date with the currentTV screen dialogue.  
Why are captions not displayed  
entirely?  
Or, captions are delayed behind  
the dialogue.  
There is no clock function on this unit.  
How can I set the clock ?  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Troubleshooting Guide  
If the unit does not perform properly when operated as instructed in this manual,  
check the following chart and all connections once before calling for service.  
Symptom  
Remedy  
Make sure the AC power cord is plugged in.  
Make sure that the AC outlet supplies the proper voltage, plug another electrical  
appliance into the AC outlet to ensure that AC outlet operates normally.  
If a power failure occurs, unplug the AC power cord for 1 minute to allow the unit to  
reset itself.  
No power  
Press only one button at a time. Do NOT press more than one button at the same time.  
Ensure that no buttons on the remote are depressed and move freely.  
Control button does not work.  
Check whether the connection of the antenna, cable receiver or satellite box is  
connected correctly.  
Check whether all the cables to the unit are connected to the correct output jack of  
your device like BD/DVD recorder.  
Power is ON but no screen  
image.  
Make sure that the selected input mode is connected to the working input jack.  
Check if your computer is NOT in sleep mode when the input mode of this unit is in PC  
mode.Tap any key on the keyboard to wake up your computer.  
Check if the power is on.  
Check if the right input mode is selected.  
Check whether all the cables to the unit are connected to the correct output jack of  
your device like BD/DVD recorder.  
View otherTV channels.The problem might be limited to the broadcasting station or  
weak signal strength.  
Turn off the unit and wait for about 1 minute, then turn on the unit again.  
Check whether the connection of the antenna, cable receiver or satellite box is  
connected correctly.  
No picture or sound  
Make sure that the selected input mode is connected to the working input jack.  
Check if your computer is NOT in sleep mode when the input mode of this unit is in PC  
mode.Tap any key on the keyboard to wake up your computer.  
Make sure that the sound is not muted. Press MUTE so that the volume bar and current  
volume level will appear on theTV screen.  
Make sure that the volume is NOT set to [ ] or [Mute]. If so, use
VOL +/–
to adjust the  
0
desired volume.  
View otherTV channels.The problem might be limited to the broadcasting station.  
Adjust [Color] in the main menu.  
No color  
Adjusted [Picture] or [Sound]  
settings are not effective every  
time the unit is turned on.  
You must set [Home] in [Location].  
p.30  
Otherwise, the settings you adjusted will not be memorized after you turn off the unit.  
Electrical interference from nearby appliances may affect picture quality.  
Adjust [Contrast] and [Brightness] in the main menu.  
View otherTV channels.The problem might be limited to the broadcasting station or  
weak signal strength.  
Sound OK, picture poor  
For the best picture quality, watch "High Definition" wide screen programs.  
If the HD content is not available, watch "Standard Definition" programs instead.  
View otherTV channels.The problem might be limited to the broadcasting station or  
weak signal strength.  
Check if the audio cable is connected in correctly.  
Picture OK, sound poor  
You may be getting interference from electrical appliances, automobiles, motorcycles or  
uorescent lights.  
Try moving the unit to another location to see if this is the cause of the problem.  
You see a distorted picture or  
hear an unusual sound.  
Electrical interference from nearby appliances may affect picture quality.  
View otherTV channels.The problem might be limited to the broadcasting station.  
Ghosts, lines or streaks in picture  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
Symptom  
Remedy  
When the capabilities of the unit exceed the capabilities of the digital broadcasting, the  
signal will be increased to match the capabilities of the display of the unit.This may cause  
noise or trash.  
You see "noise" or "trash" on the  
screen.  
Different color marks on theTV  
screen  
View otherTV channels.The problem might be limited to the broadcasting station,  
missing data or pixelation.  
This unit will memorize the volume level from the last time you adjusted it.  
If the volume of the sound from another device is higher or lower, then the loudness will  
change.  
You switch to a different input  
and the volume changes.  
You switch to a different input  
and the screen size changes.  
This unit will memorize the viewing mode from the last time you used the particular  
input modes.  
The display image does not cover • If you are watchingTV or using the CompositeVideo, S-Video, ComponentVideo or  
the entire screen.  
HDMI with 480i Input, press FORMAT repeatedly to switch various screen modes.  
Captions are displayed as a white  
box.  
No caption is displayed in the  
Closed Caption-supported  
program.  
Interference from buildings or weather conditions may cause captioning to be incomplete.  
Broadcasting station may shorten the program to insert advertisement.  
The closed caption decoder cannot read the information of the shortened program.  
Black box is displayed on theTV  
screen.  
The text mode is selected for caption. Select [CC-1] [CC-2] [CC-3] [CC-4] or [Off]  
Note  
The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a xed point of blue, green or red.  
This is not to be considered a defect in the LCD screen.  
Some functions are not available in specic modes, but this is not a malfunction. Read the description in this manual for more details on correct operations.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Maintenance  
INFORMATION  
Cabinet Cleaning  
Wipe the front panel and other exterior surfaces of the  
unit with a soft cloth immersed in lukewarm water and  
wrung dry.  
Never use a solvent or alcohol. Do not spray insecticide  
liquid near the unit. Such chemicals may cause damage and  
discoloration to the exposed surfaces.  
Glossary  
ATSC  
Acronym that stands for AdvancedTelevision Systems Committee and  
the name of the digital broadcasting standards.  
Aspect Ratio  
The width of aTV screen relative to its height. ConventionalTVs  
are 4:3 (in other words, theTV screen is almost square); widescreen  
models are 16:9 (theTV screen is almost twice as wide as its height).  
Panel Cleaning  
Wipe the panel of the unit with a soft cloth. Before cleaning  
the panel, disconnect the AC power cord.  
ComponentVideo  
This is a video signal format that conveys each of 3 principal colors  
of light (red, blue and green) through different signal lines.This allows  
the viewers to experience picture colors as original as it is.There are  
several signal formats, includingY/Pb/Pr andY/Cb/Cr.  
Servicing  
Dolby Digital  
Should your unit become inoperative, do not try to correct  
the problem yourself.There are no user serviceable parts  
inside.Turn off the unit, unplug the AC power cord and call  
our toll free customer support line found on the cover of this  
manual to locate an authorized service center.  
The system developed by Dolby Laboratories to compress digital  
sound. It offers stereo sound (2ch) or multi-channel audio.  
HDMI
(High-Definition Multimedia Interface)  
Interface that supports all uncompressed, digital audio/video formats  
including set-top box, BD/DVD recorder or digital television, over a  
single cable.  
HDTV (High DefinitionTV)  
Ultimate digital format that produces high resolution and high picture  
quality.  
IR Signal Check  
If the remote control is not working properly, you can use a  
digital camera (including a cellular phone with built-in camera)  
to see if it is sending out an infrared signal.  
NTSC  
Acronym that stands for NationalTelevision Systems Committee and  
the name of analog broadcasting standards.  
Off the air NTSC signals are no longer being sent by major  
broadcasting stations in the USA.  
With a digital camera  
(including built-in cell phone cameras):  
Point the Digital Camera towards the remote  
control infrared diode at the front of the  
remote control. Press any button on the  
remote control and look through the camera  
display. If the infrared pulsating light appears  
through the camera, the remote control is  
sending out an IR signal.  
PIN code  
A stored 4-digit number that allows access to parental control features.  
SAP (Secondary Audio Program)  
Second-audio channel delivered separately from main-audio channel.  
This audio channel is used as an alternate in bilingual broadcasting.  
SDTV (Standard DefinitionTV)  
Standard digital format that is similar to the NTSC picture quality.  
S-Video  
Offers higher quality images by delivering each signal, color (c) and  
luminance (y) independently of each other through a single cable.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
Other Specications  
General Specications  
Terminals  
TV format  
ATSC/NTSC-M TV standard  
Antenna Input VHF / UHF / CATV  
75Ω unbalanced (F-type)  
500mV rms  
Closed caption system  
Audio Input  
CompositeVideo Input  
RCA jack x 1  
RCA jack (L/R) x 6  
§15.122/FCC (digital CC)  
§15.119/FCC (analog CC)  
1V p-p (75Ω)  
Channel coverage (ATSC/NTSC)  
Terrestrial DTV (ATSC)  
VHF 2~13  
S-Video Input Mini DIN 4pin jack x 1  
Y
1V p-p (75Ω)  
C
286mV p-p (75Ω)  
ComponentVideo Input  
UHF 14~51 each channel has e.g.)  
2.1~2.9, 3.1~3.9, etc.  
RCA jack x 3  
Y
1V p-p (75Ω)  
Terrestrial Analog (NTSC)  
Pb/Cb 700mV p-p (75Ω)  
Pr/Cr 700mV p-p (75Ω)  
VHF 2~13  
UHF 14~69  
HDMI Input  
Coaxial Digital Audio Output  
RCA jack x 1  
HDMI 19pin x 3  
CATV  
2~13, A~W,  
W+1~W+94 (analog W+1~W+84),  
A-5~A-1, 5A  
500mV p-p (75Ω)  
500mV rms  
Audio Output RCA jack (L/R) x 2  
Tuning system  
Channel access  
Channel frequency synthesized tuning  
system  
Remote control  
Direct access keyboard,  
Programmable scan, and up/down  
Digital encoded infrared light system  
Operating temperature  
41°F (5°C) to 104°F (40°C)  
Power requirements  
120V~ AC +/- 10%, 60Hz +/- 0.5%  
Electrical Specication  
Audio Output  
10W, 8Ω x 2  
For 32MF330B  
LCD  
32inches (31.5 inches measured diagonally)  
Power consumption (maximum)  
145W  
<without base>  
<with base>  
Dimensions  
Width 30.0 inches(760.0mm) 30.0 inches(760.0mm)  
Height 20.5 inches(519.3mm) 22.2 inches(563.0mm)  
Depth 4.3 inches(107.0mm) 9.4 inches(238.0mm)  
18.96 lbs. (8.60kg)  
20.07 lbs. (9.10kg)  
Weight  
LCD  
For 26MF330B  
26inches  
Power consumption (maximum)  
110W  
<without base>  
<with base>  
Dimensions  
Width 25.9 inches(656.0mm) 25.9 inches(656.0mm)  
Height 17.7 inches(448.0mm) 19.2 inches(487.0mm)  
Depth 4.5 inches(112.0mm) 9.3 inches(234.0mm)  
14.89 lbs. (6.75kg)  
15.88 lbs. (7.20kg)  
Weight  
Designs and specications are subject to change without  
notice and without our legal obligation.  
If there is a discrepancy between languages, the default  
language will be English.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
English  
LIMITED WARRANTY  
( )  
(
)
NINETY 90 DAY LABOR / ONE 1 YEAR PARTS  
WARRANTY COVERAGE:  
This warranty obligation is limited to the terms as set forth  
below.  
mission, or (d) if any serial number has been removed or defaced,  
or (e) product, accessories or consumables sold “AS IS” without  
warranty of any kind by including refurbished product sold “AS  
IS” by some retailers.  
WHO IS COVERED:  
This product warranty is issued to the original purchaser or the  
person receiving the product as a gift against defects in materials  
and workmanship as based on the date of original purchase  
(“Warranty Period”) from an Authorized Dealer. The original  
sales receipt showing the product name and the purchase date  
from an authorized retailer is considered such proof.  
This Limited Warranty does not cover:  
Shipping charges to return defective product.  
Labor charges for installation or setup of the product, adjust-  
ment of customer controls on the product, and installation or  
repair of antenna/signal source systems outside of the product.  
Product repair and/or part replacement because of improper  
installation or maintenance, connections to improper voltage  
supply, power line surge, lightning damage, retained images or  
WHAT IS COVERED:  
This warranty covers new products if a defect in material or  
workmanship occurs and a valid claim is received within the  
Warranty Period. At its option, the company will either (1)  
repair the product at no charge, using new or refurbished  
replacement parts, or (2) exchange the product with a product  
that is new or which has been manufactured from new, or ser-  
viceable used parts and is at least functionally equivalent or most  
comparable to the original product in current inventory, or (3)  
refund the original purchase price of the product.  
tent for extended periods, product cosmetic appearance items  
due to normal wear and tear, unauthorized repair or other  
cause not within the control of the company.  
Damage or claims for products not being available for use, or  
for lost data or lost software.  
Damage from mishandled shipments or transit accidents when  
returning product.  
Replacement products or parts provided under this warranty are  
covered against defects in materials and workmanship from the  
date of the replacement or repair for ninety (90) days or for the  
remaining portion of the original product’s warranty, whichever  
provides longer coverage for you. When a product or part is  
exchanged, any replacement item becomes your property and the  
replaced item becomes company property. When a refund is  
given, your product becomes company property.  
it to operate in any country other than the country for which  
it was designed, manufactured, approved and/or authorized, or  
A product used for commercial or institutional purposes  
(including but not limited to rental purposes).  
can be provided.  
Failure to operate per Owner’s Manual.  
Note: Any product sold and identified as refurbished or  
renewed carries a ninety (90) day limited warranty.  
TO OBTAIN ASSISTANCE…  
Contact the Customer Care Center at:  
1-866-341-3738  
Replacement product can only be sent if all warranty  
requirements are met. Failure to follow all requirements  
can result in delay.  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS  
WARRANTY IS THE EXCLUSIVE REMEDY FOR THE CON-  
SUMER, WITH THE ISSUING COMPANY NOT LIABLE FOR  
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR  
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON  
THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY  
APPLICABLE LAW, ANY IMPLIED WARRANTY OF MER-  
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE  
ON THIS PRODUCT IS LIMITED IN DURATION TO THE  
DURATION OF THIS WARRANTY.  
WHAT IS NOT COVERED - EXCLUSIONS AND LIMI-  
TATIONS:  
This Limited Warranty applies only to new company manufac-  
to any hardware product or any software, even if packaged or  
sold with the product, as manufacturers, suppliers, or publishers  
may provide a separate warranty for their own products pack-  
aged with the bundled product.  
The company is not liable for any damage to or loss of any pro-  
grams, data, or other information stored on any media contained  
within the product, or other additional product or part not cov-  
ered by this warranty. Recovery or reinstallation of programs,  
data or other information is not covered under this Limited  
Warranty.  
Some states do not allow the exclusions or limitation of inciden-  
tal or consequential damages, or allow limitations on how long an  
implied warranty lasts, so the above limitations or exclusions may  
not apply to you.  
This warranty does not apply (a) to damage caused by accident,  
abuse, misuse, neglect, misapplication, or non-supplied product,  
(b) to damage caused by service performed by anyone other than  
company approved Authorized Service Location, (c) to a product  
FUNAI CORPORATION, Inc. 19900 Van Ness Avenue, Torrance, CA 90501  
Printed in China  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  

Lenovo Computer Monitor L220x User Manual
Lenovo Projector L1210E User Manual
Lenox Air Conditioner Elite Series XP16 Units Heat Pumps User Manual
LG Electronics Clothes Dryer DLE0442G User Manual
LG Electronics CRT Television CT 25 User Manual
Loewe Portable Speaker Auro 2216 PS User Manual
Logitech Computer Keyboard K811 User Manual
Magnavox DVD VCR Combo 1VMN26713A User Manual
Makita Drill DP4010 User Manual
Mercedes Benz Automobile 2003 C 230 Kompressor Sport User Manual