Mace DVR DVR0404RW User Manual

Mace Security Products, Inc. Presents:

Digital Video Recorder based on Mpeg4 Technology

Operational Manual

DVR0404RW

DVR0804RW

DVR1604RW

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

General Safety Precautions

This manual applies to Mace DVR0404RW (4-Channel CD-R Writer) and DVR0804RW (8-Channel

CD-R Writer). DVR0804RW has been used as the example in all illustrations.

1. Installation Environment

2. Open Product Box and Verify Contents

3. Before Power-up

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

1. Installation Environment

An UPS (Uninterrupted Power Supply) with power surge protection is strongly

recommended for DVRs and all associated devices (routers, DSL modems, etc)

Avoid extreme heat

Avoid direct sunlight

Avoid excessive humidity

Maintain horizontal mounting

Avoid excessive vibrations

Do not stack other devices on top of the DVR

Operate in well ventilated place, do not block the cooling fan

ꢀ

2. Open Product Box and Verify Contents

Check for the following accessories:

One power cord

One hard disc Ribbon Cable

One operation manual

One CD for utility software (normally it is not needed).

One remote control unit

Two AAA batteries

3. Before Power-up

Make sure the orange tab is set to 110V at the back of the DVR power supply

Be sure the UPS power supply is properly connected

Be sure to plug power cord into a reliable 110 VAC power source

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

Table Of Contents

General Safety Precautions ················································································· 3

1. Installation Environment··········································································· 4

2. Open Product Box and Verify Contents···················································· 4

3. Before Power-up······················································································· 4

Chapter 1: Product Specifications and Features ················································· 7

1. Product Specification ·············································································· 2

2. Product Features ······················································································· 3

3. Storage Matrix ························································································ 4

Chapter 2: Basic System Operations ································································· 13

1. Start/Stop the DVR ··············································································· 14

2. Recording································································································ 15

3. Alarm Input/Output················································································· 16

4. Pan-Tilt Control ······················································································ 16

5. Network Operation ················································································· 16

Chapter 3: Operations from Front Panel ··························································· 17

1. Front Panel Overview············································································· 18

2. Detail Key Function················································································ 19

3. Enter/Leave the Operation Menu···························································· 21

4. Maneuver in the Operation Menu··························································· 22

5. Menu Overview ······················································································ 23

6. Operation Description············································································· 27

6.1 Recording Control············································································· 27

6.2 Playback···························································································· 27

6.3 Pan-Tilt and Zoom Camera Control·················································· 29

6.4 Menu Detail ······················································································ 30

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

Chapter 4: Operations over Network ································································ 37

1. Setting Up the Client End······································································· 38

2. Login and Logout ··················································································· 38

3. Operation of the Right Click Menu Items··············································· 40

4. Record Search and Playback··································································· 43

5. System Configuration ············································································· 45

6. Assistant·································································································· 50

Chapter 5: System Connections ········································································ 57

1. DVR Rear View······················································································ 58

2. RS232 Port Connection ·········································································· 59

3. 25 Pin Alarm Transfer Box·······································································60

4. RS-485 Port Connection········································································· 61

Chapter 6: Serial Connection ············································································ 64

1. System Setting ························································································ 65

2. Software Upgrade Through Serial Port··················································· 66

Appendix 1 Remote Control Unit ····································································· 67

Appendix 2 Frequently Asked Questions ·························································· 68

Appendix 3 Hard Disk Installation ··································································· 69

LIMITED WARRANTY·······················································································71

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

Chapter 1

Product Specifications And Features

1. Product Specifications

ꢀꢁ Product Featuresꢂ

ꢃꢁ Storage Matrixꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

1. Product Specifications

Parameter

4 Channel

8 Channel

Processor

Operation system

Model

AMD ELANSC520/133 embedded microprocessor

Real-time operation system - RTOS

DVR0404RW

DVR0804RW

8 Channel (NTSC/PAL) BNC 1.0V_{P- P}75ꢀ

Video input

4 Channel (NTSC/PAL) BNC 1.0V_{P- P}75ꢀ

Video output

Audio input

1 Channel PAL/NTSC BNC 1.0V_{P- P}75ꢀ video signal

4 Channel 200-1000mv10Kꢀ (BNC)

8 Channel 200-1000mv10Kꢀ (BNC)

Audio output

Video display

Video standard

System resource

Image resolution

Motion detection

1 Channel 2000mv 1Kꢀ (BNC)

1(Full Screen) & 4(Quad) window displays

1(Full Screen),4(Quad),9 (3x3) window displays

NTSC 525 line, 60f/s – PAL 625 line, 50f/s

Real-time recording, one channel playback and network operation simultaneous (Triplex)

Real-time monitor 704×576, playback 352×288, VGA output 720×576

Area setting: 396 detection areas on the screen; detection sense setting: 3 levels detection sense for

each area

Video compression

Audio compression

Image compression

rate

MPEG-4 CBR (fixed frame rate); MPEG-4 VBR (variable frame rate)

Audio - ADPCM 28.8 Mb/hourꢀ G.729 - 3.6 Mb/hourꢀ Video - 40-460 Mb/hour

352×288CIF format - 176×144QCIF format - 704×576 4CIF format.

Video recording

Real-time mode: NTSC 1f/s - 30f/s for each channel adjustable. PAL 1f/s - 25f/s for each channel

speed

adjustable;

Image quality

CDRW

6 levels selectable

Built-in CDRW writer for data backup

A 80 Gigbyte Hard disk is preinstalled

Pre-Installed Hard

Disk

Hard Disk Expansion

Inside equipped 4 IDE ports, able to install 8 HDDs inside, With CDRW option, up-to 5 internal

HDDs supported

HDD space used

Alarm input

Alarm output

Alarm relay

Audio - ADPCM 28.8Mb/hourꢀ G.729 - 3.6Mb/hourꢀ Video - 40-460Mb/hour

8 channel voltage alarm input – 5 to 15V DC necessary for the alarm input.

3 channels output, - output in open/close contact or controllable - 12V output -

30VDC 1A, 125VAC 0.5A - relay output.

Network connection

Pan-tilt control

Power

RJ45 10M/100M Ethernet connection

RS485

110VAC/220VAC

Power consumption

Working temperature

Working humidity

Barometric pressure

Size

60W

75W

10C – 55C

10ꢁ - 90ꢁ Relative

86kpa - 106kpa

2U standard industrial case 441mm (Wide) x 430mm (Deep) x 89mm (High)

11KG in Box

Weight

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

Parameter

16 Channel

AMD ELANSC520/133 embedded microprocessor

Processor

Operation system

0RGHOꢀ

Real-time operation system˄RTOS˅

'+ꢁ'95ꢂꢃꢄꢅ5:ꢀ

Video input

Video output

Audio input

Audio output

Video display

Video standard

System resource

Image resolution

Motion detection

ꢂꢃ Channelꢀꢆ176&ꢇ3$/ꢈ BNC˄1.0V_{P- P}75¡˅ꢀ

ꢂ Channelꢀ3$/ꢇ176&ˈBNC˄1.0V_{P- P}75¡˅video signalꢀ

ꢂꢃ Channel 200-3000mv10K¡(RCA)ꢀ

ꢂ Channelꢀꢀꢀ2000mv 1K¡(RCA)ꢀ

1ˈ4 ,16 window display

NTSC˄525 line, 60f/s˅ˈPAL˄625 line, 50f/s˅ꢀ

16 chs real-time recording, one channel playback and network operation simultaneousꢀ

Real-time monitor 704h576, playback 352h288, VGA output 720h576ꢀ

Area setting: ꢉꢊꢃ detection areas on the screen; detection sense setting: 3 levels detection sense for

each areaꢀ

Video compression

Audio compression

03(*ꢁꢅ CBR (fixed frame rate); 03(*ꢁꢅ VBR (variable frame rate)ꢀ

Audio˖ADPCM 28.8Mbyte/hourꢀꢀ Video˖40-460Mbyte/hour

Image compression 352h288 CIF formatˈ 704h576 4CIF formatꢀ

rate

Video

speed

recording MPEG mode: PAL 1frame/10second-25f/s for each channel adjustable; NTSC 1frame/10second-30f/s

for each channel adjustable

Image quality

Hard diskꢀ

6 levels selectable

Inside equipped 4 IDE ports, able to install 8 HDDs inside, expand with external HDD case for another

12 HDDsꢀ

$XGLR˖$'3&0ꢀꢋꢌꢍꢌ0E\WHꢇKRXUꢀꢀ 9LGHR˖ꢅꢄꢁꢅꢃꢄ0E\WHꢇKRXUꢀ

16 channel voltage alarm input˄ˇ5̚ˇ15V D. C. Needed for the alarm input˅

+''ꢀVSDFHꢀXVHGꢀ

Alarm input

Alarm output

Alarm relay

02'(0ꢀconnectionꢀ

Network connection

Pan-tilt control

Backup

6 channels output, ˄output in open/close contact˅

24VDC 1A,220VAC 0.15A˄relay ouput˅

56ꢋꢉꢋꢀ

RJ45 10M/100M Ethernet connection

Alarm input and output port,ꢀ56ꢋꢉꢋ

&'ꢁ5ǃ86%ǃ+''

Power

110VAC/220VAC

Power consumption

Working temperature

Working humidity

Barometric pressure

75W

ˉ10ćˉˇ55ć

10̦ˉ90̦

86kpaˉ106kpa

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

2. Product Featuresꢂ

Real-time Monitor (Video Displays)

1 Video output port to Video Monitor and 1 VGA port for video output to PC Type Monitor.

Single window (Full Screen) /4 windows (Quad) /9 windows (3x3) monitor diplay.

Compression Method

Multiple video compression modes: MPEG4 fixed frame variable frame.

4, 8, 16-channel audio/video real-time compression, independent hardware compression for

each channel, stable synchronization of sound and image.

Storage

Internally can hold 8 IDE-compatible large capacity Harddisk(HDD)

Alternative HDD operations that will reduce the power consumption and heat emission.

Overwrite (FIFO) and Stop (HDD Full) modes for DVR HDD recording.

Back-up

Built-in CD-RW drive to back up records onto CD-R disks, upgradeable to DVR-RW drive.

USB port for external back up of records.

Download the files on DVR to local PC through network.

Play and Record

Supports multiplexed operation: live monitor, record, search for downloading, one channel

play-back, and remote transmission simultaneously.

Multiple recording mode: Manual – Timing – Alarm - Motion Detection. Note: Alarm

Recording and Motion Recording have Pre-Alarm function.

Playback: With PIP or Multi-Channel Real-Time Monitor. Playback also available using

Network Connection.

Fast search for reviewing manual recording and alarmed recording.

Multiple play-back modes: X2, X4 & X8 fast play, pause, 15F/S, 5F/S slow play and frame by

frame playback.

Displays Time/Date during playback.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

Alarm relay

8 channel external alarm input, video lost alarm and motion detection alarm.

Multi channel relay switch alarm output activates alarm relay and on-site light control.

Circuit Protection for Alarm inputs and outputs.

Pan-tilt Control

Supports Camera Pan-Tilt-Zoom (PTZ) Functions using RS485 Communication Protocol.

Integrates multiple protocols to control various PTZ speed domes.

Communication connection port

DB-25- (25 pin) connection for alarm inputs and PTZ control.

RS232 port for the connection with keyboard for central control, or with the computer serial

port for system upgrades and diagnostics.

Standard Ethernet port for remote viewing and control.

Remote real-time monitor.

Pan-tilt-zoom control.

Record search and real-time playback. Note: playback quality dependent on network conditions.

Downloading records through network.

System programming, settings & modification and system software upgrades available online.

Remote alarm processing and system log review remotely.

Embedded TCP/IP protocol and RTOS (Real Time Operating System) supports Web server

direct connection to operate and control all the above functions.

Administration mode: Three USER levels for logging in remotely. Each user login is

password protected.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

3. Storage Matrix

The HDD Capacities and Recording lengths are determined by capacity of the installed HDDs and the selected

image level.

The following storage time is based on the average use for HDD space for single channel recording.

Average

HDD

Image level

Resolution

Frames

Maximum data flux

128Kb/S

Coding

CBR

space˄/hour˅

ꢉꢎꢋꢏꢋꢌꢌ

40MB

ꢉꢎꢋꢏꢋꢌꢌ

256Kb/S

384Kb/S

512Kb/S

768Kb/S

1Mb/S

80MB

120MB

160MB

240MB

320MB

Note: Adjustable frame rates, from 1fs to 30f/s can be selected. User can choose based on own needs.

Using other than 30f/s (Real time), HDD (Hard Disk) space can be greatly increased.

Following are storage calculation guidelines (in the number of Days):

Img

Quality

30F/S

128kb/s

256kb/s

384kb/s

512kb/s

768kb/s

1024kb/s

1-ch

4-ch

15*

8-ch

80G

1(128kb/s)

2(256kb/s)

3(384kb/s)

4(512kb/s)

5(768kb/s)

6(1024kb/s)

MP4(CBR)

* This reads that with a 80G harddisk, at CBR (constant bit rate) and Image Quality 1, DVR will be able to

record 15 days for 4 camera inputs.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

1F/S 1-ch 4-ch 8-ch

155 78

Img Quality

30F/S 1-ch

4-ch

8-ch

80G

116kb/s

160kb/s

212kb/s

330kb/s

447kb/s

825kb/s

12.5kb/s

621

312

176

156

124

25kb/s

44kb/s

50kb/s

62kb/s

88kb/s

MP4(VBR)

Img Quality

2F/S 1-ch

4-ch

8-ch

3F/S 1-ch

4-ch

8-ch

80G

25kb/s

44kb/s

50kb/s

63kb/s

78kb/s

92kb/s

311

176

156

124

100

44kb/s

45kb/s

55kb/s

84kb/s

100kb/s

122kb/s

176

172

140

MP4(VBR)

Img Quality

10F/S 1-ch

71kb/s

4-ch

8-ch

12F/S 1-ch

4-ch

8-ch

80G

108

14 80kb/s

109kb/s

133kb/s

175kb/s

258kb/s

443kb/s

130kb/s

149kb/s

210kb/s

275kb/s

525kb/s

MP4(VBR)

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

ꢂ

Chapter 2 Basic System Operations

ꢂ

1. Start/Stop the DVR

ꢀꢁ Recordingꢂ

ꢃꢁ Alarm Input/Outputꢂ

ꢄꢁ Pan-tilt Controlꢂ

ꢅꢁ Networkꢂ

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

1. Start/close the recorder

ꢂꢍꢂ Start the recorder

Plug in the power line; switch on the power button at the back of the recorder; power indicator light on; DVR

on; default single window for the video output displays; press Enter the Log-in screen appears on Monitor; If

the starting time is within the programmed recording time, the system will start recording function automatically.

Channel indicator lights will indicate the cameras in record mode. The system will work in a normal manner.

Note: if the system stops during HDD Boot detection, the HDD may not be installed right and please check the

HDD connections (Ribbon and Power Connections). *Please unplug the 120VAC power supply during HDD

installation*

1.2 Enter the setting menu

Before you enter the menu, you must input the password. There are two levels of password—User password and

Administrator password.

Administrator passwordꢂꢂꢂꢂꢂꢂꢆꢆꢆꢆꢆꢆꢀ

General user passwordꢂꢂꢂꢂꢂꢂꢂꢇꢇꢇꢇꢇꢇꢀ

If input the user password, you have to input again at the next login; you are also not allowed to enter

system setting and admin setting.

Note: For the consideration of security, please change the Administrator password in admin settings.

Refer to Chapter 4 Front Panel Menu Operation for details.

1.3 Turning off the DVR

Press the POWER key on the front panel for 4 seconds to stop the current operations. Then switch off the power

button at the DVR rear to turn off the power.

1.4 Power off recovery

When the power is cut off abnormally, the recorder will recall it’s last state and continue where it left off. The

state indicator light is the same as it was before the power off.

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

2. Recording

The default recording mode after startup of the DVR is 24 hr continuous recording for each channel. The

User can program customized recording times for each camera. Instructions for the different recording modes are

as follows:

a) Timing Recording:

· Enter the menu, and set the timing period for the recording. See details at Menu>System setting>Timing

b) Manual Record Selection

· Press “Record” button on the remote controller or “Rec” on the front panel.

· Check the status of each channel in the recording menu; The Highlighted channels are in record mode.

· To select the channel to be recorded, press the related number key. Selected camera # will highlight on

your screen. When all cameras that need to be recorded are selected, press Enter to begin the recording.

· Repeat above steps and remove the highlight to stop the camera from recording. ·Press Cancel or ESC to

return without changes.

c) Alarm recording

· Connect the alarm input according to the device connection and the instructions.

·Program the related settings in the menu to start Alarm recording. See details at Menu>System

setting>Alarm setting

d) Motion detection recording

· Record the channel only in need of motion detection. First confirm whether this channel is programmed in

Timing Recording; if it is, please turn off Timing Recording for the selected Camera..

· Program the related settings in the menu to start Motion detection recording. See details at

Menu>System setting>Motion detection.

3. Alarm connection operation

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

· Connect the alarm input according to the device connection and the instructions.

· Connect the related alarm output relay on the DVR to associated alarm device. Example: lights, beeper, etc.

· Program the associated information in the menu. See details at Menu>System setting>Alarm setting

4. Pan-tilt control operation

· Confirm the proper connection of the pan-tilt-zoom and Communication Protocol. Set the Camera address.

· Confirm the proper wiring connection between the PTZ and RS-485 A & B lines and DVR’s 25-pin port’s A

& B lines.

· Set up the programming. See details at Menu>System setting>Control

· Select full screen call-up of associated P/T/Z Camera.

· Press and hold “Assistant” on the remote controller or “Fn1” on the front panel to select

· Use direction arrow keys to move and control the selections on the screen

5. Network connection operation

· Confirm correct network connections between DVR and computer

· Set the IP address, subnet mask and gateway of the computer and DVR separately. If there is no router in the

network, only the IP address is needed. If there are routers in the network, please enter the related gateway

and subnet mask.

· Ping ***.***.***.*** the IP address of the DVR to check the link of the network. A successful reply shall

look like (TTL value less than 64 ms is normal):

Reply from 68.153.205.130: bytes=32 time=31ms TTL=57

· Open IE browser and input the IP address of the DVR you want to log in to.

· For Network operation see details at Chapter 4

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

ꢂ

Chapter 3 Operations From Front Panel

1. Front Panel Overview

ꢀꢁ Detail Key Functionꢂ

ꢃꢁ Entering the Operation Menuꢂ

ꢄꢁ Maneuver in the Operation Menuꢂ

ꢅꢁ Menu Overviewꢂ

6. Operation Description

6.1 Recording

6.2 Playback

6.3 Pan-Tilt and Zoom Camera Control

6.4 Menu Detail

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

1.ꢂFront Panel Descriptionꢂ

ꢂ

Power Switch

CD-RW

Camera Selection #

Onscreen Addr Entry

Recording Light

Left Direction

Control Cover

IR Remote Receiver

ESC (Cancel)

10. Enter

11. Down Direction

12. Up Direction

16. FN2 (Function 2)

20. Standby Light

13. Right Direction

14. Information

18. FN1 (Function 1)

22. Multi-screen Selection

26. Slow Play

15. Single & PIP Selection

19. FN Indication Light

17. Multi-screen Selection

21. Jog Shuttle

23. Rec (Recording Control) 24. ESC (Cancel)

27. Play/Pause 28. Fast Forward

25. Replay Last Selection

29. Jump to Next Section

30. Enter

Note: Outside Ring of the jog shuttle when turning clockwise is equal to right direction arrow, turning

counterclockwise is equal to left direction arrow; inner circle turning clockwise equal to down direction,

otherwise equal to up direction.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

2. Keys functions

Order

Key name

Power switch and

indication light

Camera Selection

Numbers

Logo

POWER

Function

Power switch - Power off by pressing the key 4 seconds.

Indication light

Manual Password # input, window shift or number input; 10

is used for numeric input 0.

1, 2, 3 etc.

LED (Red) on

numbers

Recording light

If the LED light is RED, it means the recording is on

Plastic Cover

CD-RW

Black plastic

CD-RW

ADD

Dust-proof Cover

Used to Back-up records

Input remote control address for the operation of DVR.

Address

L & R On screen Cursor Control; shifting level 1 and level 2

menu; Left and Right Camera Pan control.

7 & 13

Left & Right Arrows

Up and Down Onscreen Cursor Control; change setup;

change number; Camera Tilt control.

11 & 12

Up & Down Arrows

IR Remote receiver

Cancel

p q

Used to receive the remote signal.

Cancels cursor selection.

9 & 24

ESC

During playback, restore to real-time monitor.

Enter Cursor Selection.

Enter

ENTER

Enter main menu.

Press to show the system information.

Information

INFO

Single window display

Shift the window to single window

ꢀ

In the Full Screen Mode:

Press the key to display the menu of the Camera PTZ.

When setting Motion Detection fields, Fn1 Enables Cursor

field selection.

Fn1

Fn2

Function assistant 1

During playback, display the playback status bar

During playback work with number key to realize PIP for the

playback and real-time monitor.

Function assistant 2

Multi-Screen Display

Select to change from Full screen to multi-window display.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

Assistant indication

Indication light for when Function assistant keys are used.

light

Indicator light for

Light on when DVR is in stand by Mode.

standing by

Direction control: outer Ring for Left and Right direction,

inner Ring for up and down; When in playback, outer circle

can control reverse, and multi-speed play.

Select for Multi-Screen; During playback, shift between

Playback and Real time display.

Jog shuttle

Multi-Screen Display

MULT

Record

Start/stop recording, use with arrow keys

Play the previous recording file.

REC

Play last section

Slow play

ꢂ

3 levels of slow play speed adjustments: (15f/S - 5f/S &

frame by frame)

Play/stop

Fast play

Ñ/;

When in real time mode, press to enter record search menu

3 levels of fast play speed - X2 - X4 - X8.

Play next section

Enter

Play the next recording file after the current file.

Enter

ENTER

Enter the main menu.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

3.ꢂEnter/Leave the Operation Menu

Press Enter key twice, the system will prompt for password.

Default Administrator password is “888888”.

Default User password is “666666”.

If not touched for 5 minutes, the system will automatically logout the currently user.

For security reason, the Administrator may choose to manually logout under Menu/ Logout

General

Listing

searching

Precise

Alarm

File

HDD

System INFO

System

General

rsion

Timing setting

Image setting

Alarm settingꢀ

Pan-tilt setting

Motion

Serial port

Password

File

Advanced

Output

Read default

Backup

Backup listing

Data backup

Backup

File backup

Logout

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW/DVR1604RW

Digital Video Recorder

4. Maneuver in the Menu System

Operation

step

Button-pressing

order

Instruction

Screen display

1 Confirm Enter

During real-time monitor, press to open the

password prompt, type in the correct password,

then the menu will auto open.

ꢀ

ꢀ0HQXꢀꢀꢀꢀꢀꢀꢀꢀꢀ

ꢀ

Enter main

menu and

level 1

ꢀ

2 Direction arrows Use arrows to select Icon Choice.

pqut

submenu

3 Confirm Enter

Press Enter to select choice

4 Direction

Use arrows again to select #2 submenu choice

ꢀ

ꢀ6($5&+ꢀ5(&25'ꢀꢀ

pqut

Enter level

2 submenu

5 Confirm Enter

Press Enter to select level 2 submenu

1 Use Direction Select the option to be revised, flashing item is

ꢀ

&21752/ꢀ6(77,1*ꢀ

ꢀ

Arrow

the selection.

&+ꢀ

ꢂꢀ

35272&2/ '+ꢁ&&ꢅꢅꢄꢀ

E$8'5$7(ꢀꢀꢊꢃꢄꢄꢀ

$''5ꢀꢀꢀꢀꢀꢀꢄꢄꢄꢀ

6$9(ꢀ ꢀ

2 Direction pq

Use Up/Dn arrows to revise the settings.

&$1&(/ꢀ

Set menu

contents

3 Press Enter

Save is flashing, choose to confirm whether you

want to keep the revised setting and press Enter

again.

Direction Arrow Return to the last option of the current menu

ꢀ

6($5&+!5(&25'ꢀ

Exit the

current

Cancel ESC

Exit to the last level menu

You can set the multiple channels before you exit the current menu and save all the settings together.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

ꢅꢁ Menu Overview

Main menu

Menu level 1

Menu level 2

Remarks

RECORD

Use DIRECTION arrows to perform settings

in menu level 2ꢀ

DATE

TIME

24-10-2003

2:20 PM

See detailsꢀDWꢀꢃꢍꢅꢍꢂ

PLAY START

LIST

Use DIRECTION arrows to perform setting

in menu level 2.

DATE 24-10-2003

TIME 2:20 PM

LIST SEARCH

See detailsꢀDWꢀꢃꢍꢅꢍꢂ

ALARM

Records associated with Alarm Inputs. Not

able to search motion detection records.

See detailsꢀDWꢀꢃꢍꢅꢍꢂ

DATE

24-10-2003

SEARCH START

HDD NUM 0 2

FILE INFO

HDD CAP 0 1 6 0 0 8 6M

FREE SPACE 0 0 0 0 0 0 0 M

FILE START 2003-04-12ꢀ 01˖30AM

FILE END

INDEX

2003-05-13ꢀ 09:00PM

ˍˎˏːˑ˒˓˔ꢀ

:ꢁꢀꢁꢀꢁꢀꢁꢀꢁꢀꢁꢀꢁꢀ

HARD DISK

STATE

MASTER

SLAVE

:ꢁꢀꢁꢀꢁꢀꢁꢀꢁꢀꢁꢀꢁꢀ

INFORMATION

&'5ꢀ67$7(ꢀ12ꢀ

USB STATE NO

Information cannot be modified

VERSION

BIOS VERSION 2.45

ISSUE DATE 03 01 2003

WEB VERSION 1.23

CH.1 ꢀ CH.2ꢀ

CH.3ꢀ

CH.4

0538Kb 0302 Kb 0267 Kb 0112 Kb

256M/H 132M/H 117 M/H 49M/H

CH.5 ꢀ CH.6 ꢀ CH.7 ꢀ CH.8

0663 Kb 0227 Kb 0050 Kb 0283 Kb

291M/H 99M/H 21M/H 124M/H

BPS

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

ꢂ

Main menu

Menu level 1

Menu level 2

Remarks

DATE

10-28-2003

FORMAT MM-DD-YYYY

TIME 12:22:01

FORMAT AM/PM SAVETIME

INTERVAL 005 SEC

HDDFULL OVERWRITE

RECORDLEN 15 MIN

REMOTEADDR 108

GENERAL

See details at 6.4.3

SYSTEM

SETTING

COMMCTRL NONE

SAVE

CANCEL

WEEK

SLOT1

STATE

SLOT2

STATE

SAVE

S M T W T F S

00:00 – 24:00

SCHEDULE

CANCEL

MODE

CBRꢀꢀ AV

FRAMERATE

BITRATE

REAL

1024K

IMAGE

VIDEO LOSS

COVERED

OFF

VIDEO SET DEFAULT

TITLE

01 ON

CYCLE

OFF

SAVE CANCEL

TYPE

NORAML CLOSE

RECORD CH

ALMOUT

1 2 3 4

ALARM

See details at 6.4.3

DELAY

SLOT1

SLOT2

1SEC

00:00 – 24:00 ON

00:00 – 24:00 OFF

ALMSVR IP 192.168.000.118 OFF

SAVE CANCEL

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Main menu

Menu level 1

PANTILT

Menu level 2

Remarks

PROTOCOL NONE

BAUDRATE 4800

CONTROL

See details at 6.4.3

ADDRESS

SAVE

000

CANCEL

192.168.001.108

255.255.255.000

192.168.001.001

00080

37777

TCP

SUBNETMASK

GATEWAY

WEB PORT

TCP PORT

MONITOR

PLAYBACK

SAVE

NETWORK

SYSTEM

SETTING

TCP

CANCEL

DELAY

30 SEC

MOTION

ALMOUT OFF

DETECTION

LEVEL

AREA

TIME1

TIME2

MID

SET

See details at 6.4.3

00:00 – 24-00 OFF

00:00 – 24:00 OFF

SAVE

CANCEL

GUEST * * * * * *

PASSWORD

Only the Administrator password logged in is

able to change password.

CONFIRM * * * * * *

MANAGE * * * * * *

CONFIRM * * * * * *

SAVE CANCEL

See details at 6.4.4

PASSWORD ---------

FILE

DELETE

See details at 6.4.4

ADMIN

ALARM TIP

SHUTDOWN PWD

OUTPUT X/Y POINT

PLAYBACK HEIGHT 480

AUDIO MODE PCM 8KHZ

OFF

SETTING

000/000

Able to set the color of words on the menu.

Able to set the starting point of the monitor

screen and the size of the monitor screen,

playback screen.

OTHERS

TITLE COLOR

MONITOR OSD

WHITE

MAINTENACE WEEK S M T W T F S

MAINTENACE TIME 12:00 AM

SAVE CANCEL

LOAD DEFAULT CONFIGURATION?

YES NO

DEFAULT

See details at 6.4.4

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Main menu

Menu level 1

Menu level 2

Remarks

ꢀ

BACKUP RECORDS

DEVICE

HDD

CH ꢀ

BACKUP

BACKUP SPEEDꢀ NORMAL

STARTING DATEꢀ 2003-3-18

STARTING TIMEꢀ 12:18PM

ENDING DATEꢀ 2003-3-18

ENDING TIMEꢀ 5:18PM

See details at 6.4.5

ꢀ

BACKUP ꢀ ADD

START

DELETE BACKUP

DEVICE

DELETE

HDD

CONFIRM

LOGOUT

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

6.Menu Operation Description

6.1 Recording Operation

ꢂ

Model

Button-pressing order

1. Record REC

Instruction

Press to enter screen display.

Diplay

ꢀ

RECORD 1

ꢀ

2. Direction pq or Press to toggle the recording state on/off. The

the related number key highlighted Camera # means Record On or selected to

Record..

ꢀ

'95ꢄꢌꢄꢅꢀ

ꢆ([DPSOHꢈꢀ

RECORD 1

3 Direction

t u

Arrow to change camera channels. The highlighted item

means On.

4 Record

REC

Press to save the setting.

OR Enter

ꢀ

6.2 Playback operation

Button-pressing orderꢀ

ꢂꢀ3OD\ꢇ3DXVHꢀ

Instruction

Display

Press the button to enter screen display.(if logged out, log

back in with password)

ꢀ

5(&25'ꢀ6($5&+ꢀꢀꢀ

&+ꢀꢀꢂꢀ

'$7(ꢀꢀꢄꢉꢁꢄꢉꢁꢋꢄꢄꢉꢀ

7,0(ꢀꢀꢄꢊ˖ꢂꢄꢀ$0ꢀ

3/$<ꢀꢀ67$57ꢀ

ꢀ

2 Play/Pause

Press twice to begin the playback (The on screen video

displays channel, date, time). If display shows no record

found, the operation will not take effect. After the

completion of the playback, display shows “The End”.

ꢀ

5(&25'ꢀ6($5&+ꢀꢀꢀ

&+ꢀꢀꢂꢀ

'$7(ꢀꢀꢄꢉꢁꢄꢉꢁꢋꢄꢄꢉꢀ

7,0(ꢀꢀꢄꢊ˖ꢂꢄꢀ

3/$<ꢀꢀ12ꢀ5(&25'ꢀ

ꢀ

To display Record Information during playback, press Fn to display or hide the playback state bar.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

6.2.1 Playback fast play

Button-pressing order

Instruction

Display

CH1ꢀ PLAYꢀ X2

1 Fast play 8

During playback press this key to shift between 2X speed,

4X speed, or 8X speed.

2 Play/Pause

During fast play press this key to shift between play and

pause.

3 Play next section, play last Operates in playback state. Press9 :to view the next or

section

last record of the same channel.

6.2.2 Playback slow play

Button-pressing order

Instruction

Display

&+ꢂꢀ 3/$<ꢀ ꢂꢎ)ꢇ6ꢀꢀꢀꢀ

1 Slow play

ꢂ

During playback press to shift among 30f/s, 15f/s, 1f/s

speed.

2 Play/Pause

During slow play of the playback record press to shift

between play and pause.

3 Play next section, play last Works when in Playback Mode. Press9 :to view the

section next or last record of the same channel.

ꢀ

1f/s speed during slow play is a frame by frame selection.

ꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

6.3ꢂControl of Pan-Tilt and Zoom Cameras

*The PTZ Camera # must be selected on DVR before you can control the camera from

the DVR or remotely.ꢂ

ꢂ

Button-pressing order

Instruction

3UHVVꢀ)QꢀWRꢀGLVSOD\ꢀ

1 Refer to menu operation at In Control setting select the related Channel and Protocol,

&21752/ꢀ6(77,1*ꢀ

ꢀ

6.4.4

see the right picture. Set the Baudrate and Address of the

PTZ Camera. Press Enter to save.

&+ꢀ

ꢂꢀ

35272&2/ꢀ'+ꢁ&&ꢅꢅꢄꢀ

%$8'5$7(ꢀꢀꢀꢀꢊꢃꢄꢄꢀ

$''5ꢀꢀꢀꢀꢀꢀꢄꢄꢄꢀ

6$9(

&$1&(/ꢀ

2 Assistant function Fn1

When in Full Screen Mode, press Fn1 to enter the screen

display.

ꢀ

PT CONTROL

ꢀ

pꢀ

tDIRECTIONu

ꢀ

Press continuously to shift among PT CONTROL

DIRECTION LENS CONTROL ZOOM FOCUS IRIS

LIGHT CONTROL(OFF ON). Use arrows to adjust.

Control the related pan-tilt, lens and light. Use Arrows to

select.

Direction pqt u

ꢀ

LIGHT CONTROL

ꢀ

tꢀ OFF ONu

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

6.4 Menu Operation Detail

*The following Menu settings must be saved before the changes take effect.*

6.4.1 Record search

The menu for record search is pictured at the right.

5(&25'ꢀ6($5&+ꢀ

ꢀꢀꢀꢀꢀ

ꢀ

ꢂ

First set the channel#, then date and time you want to

5HFRUGꢂ

search, then select START, the playback begins.

5(&25'ꢀ6($5&+ꢀꢀꢀꢀꢀ

ꢀ

CH 1ꢀ

'$7(ꢀꢀꢋꢄꢄꢋꢁꢂꢋꢁꢄꢌꢀ

7,0(ꢀꢀꢄꢌꢐꢂꢌ$0ꢀ

3/$<ꢀꢀ67$57ꢀ

ꢀ

First set the channel #, date and time you want to search,

then select SEARCH, the screen shows the 8 recording files

following the searching time. Use pq to select the file to be

played. Press ENTER to begin the playback.

Note the letters before the record are equal to following

R—Record M—Motion Detection A—Alarm

List

/,67ꢀ6($5&+ꢀꢀꢀ

ꢀ

CH 1ꢀ

'$7(ꢀꢀꢋꢄꢄꢋꢁꢂꢋꢁꢄꢌꢀ

7,0(ꢀꢀꢂꢄꢐꢂꢄ$0ꢀ

/,67ꢀꢀꢀ6($5&+ꢀ

First set the search date, then select START, all the alarm records will

be displayed. Press pq to select the record. Press ENTER to play

the alarm record. Note: motion detection alarm can not be searched in

this category, but can be

Alarm

$/$50ꢀ6($5&+ꢀꢀꢀꢀ

ꢀ

DATE 2002-12-08

6($5&+ꢀꢀ67$57ꢀꢀ

searched in RECORD and LIST.ꢀ

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

ꢀ

6.4.2 Informtion

ꢀ

),/(ꢀ,1)2ꢀ

ꢀꢀ

ꢀ

Menu of Information is pictured at right.

ꢂ

Recording start time(the earliest recording time among all the HDDs)

File Info

),/(ꢀ,1)2ꢀꢀ

ꢀꢀ

and recording end time. The information cannot be changed.ꢀ

HDD NUM 0 2

ꢀ

HDD CAP 0 1 6 0 0 8 6M

FREE SPACE 0 0 0 0 0 0 0 M

ꢀ

FILE START 2003-04-12ꢀ 19 00 22

FILE END 2003-05-13ꢀ 17 00 44ꢀ

ꢀ

HDD State

Version

Display HDD index and the conditions of master drive and slave drive.

+''ꢀ67$7(ꢀꢀ

ꢀ

Note: The HDD being used, will show as “W”.ꢀ

,1'(;ꢀꢀꢂꢋꢉꢅꢎꢃꢑꢌꢀ

0$67(5ꢀꢀꢁ:ꢁꢁꢁꢁꢁꢀ

6/$9(ꢀꢀꢀꢁꢁꢁꢁꢁꢁꢁꢀ

&'5ꢀ67$7(ꢀꢀ12ꢀ

86%ꢀ67$7(ꢀꢀ12ꢀ

The issuing date and ID of the operating system. The information cannot

be modified.

9(56,21ꢀꢀꢀ

ꢀ

%,26ꢀ9(56,21ꢀꢋꢍꢅꢎꢀ

,668(ꢀ'$7(ꢀꢄꢉꢀꢄꢂꢀꢋꢄꢄꢉꢀ

:(%ꢀ9(56,21ꢀꢀꢀ

ꢀ

ꢀꢀꢀ%,7ꢀ5$7(ꢀꢀ

ꢀꢀꢀ67$7,67,&6ꢀ

CH.1 ꢀ CH.2ꢀ CH.3ꢀ CH.4

0538Kb 0302 Kb 0267 Kb 0112 Kb

256M/H 132M/H 117 M/H 49M/H

Real time display the frame rate of the current channels and the space

occupied

Frame rates are in Kb/s

HDD space occupied in MB/h

CH.5 ꢀ CH.6

ꢀ

CH.7

ꢀ

CH.8

0663 Kb 0227 Kb 0050 Kb 0283 Kb

291M/H 99M/H 21M/H 124M/H

ꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

6.4.3 System Setting

Picture of the System Setting Menu

See screen shot at right:

6<67(0ꢀ6(77,1*ꢀ

ꢀ

General

DATE and TIME are used to modify the current system date and time;

after the modification reserve the change by selecting SAVETIME; in

HDDFULL if selecting OVERWRITE system covers the previous

recording files; RECORDLEN can set the length of each recording

file(15 mins, 30 mins, 60 mins)Note: 15 minutes is suggested.

COMMCTRL can Activate the communication control protocols. The

existing comm control protocols are:

*(1(5$/ꢀꢀ6(77,1*ꢀꢀ

ꢀ

DATE

10-28-2003

FORMAT MM-DD-YYYY

TIME

12:22:01

FORMAT AM/PM SAVETIME

INTERVAL 005 SEC

HDDFULL OVERWRITE

RECORDLEN 15 MIN

REMOTEADDR 108

MODEM - Dial-up connection through modem.

COMMCTRL NONE

SAVE CANCEL

AB-

matrix control

Keyboard control

NONE upgrading system through serial port

Note: System time shall NOT be changed freely; otherwise it

would cause the malfunction of recording search.

Select the corresponding channel in CH. In WEEK the letter of each

Schedule

day is chosen, when the letter displays are highlighted. SLOT1 and SLOT2

express the timed recording period of the current channel. SLOT2 should

be after the ending time of SLOT1. The setting range is 00:00-24:00

STATE ON means the time setting is on. OFF means the time setting is

OFF.

6&+('8/(ꢀ5(&25',1*ꢀ

ꢀ

&+ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢂꢀ

:((.ꢀꢀꢀꢀꢀꢀꢀꢀ6ꢀ0ꢀ7ꢀ:ꢀ7ꢀ)ꢀ6ꢀ

6/27ꢀꢂꢀꢀꢀꢀꢀꢀꢄꢌꢐꢄꢄꢀ$0ꢀ̢ꢀꢄꢌꢐꢄꢄꢀ30ꢀ

67$7(ꢀꢀꢀꢀꢀꢀꢀ2))ꢀ

6/27ꢀꢋꢀꢀꢀꢀꢀꢀꢄꢌꢐꢄꢄꢀ$0ꢀ̢ꢀꢄꢌꢐꢄꢄꢀ30ꢀ

67$7(ꢀꢀꢀꢀꢀꢀꢀ2))ꢀ

ꢀꢀꢀꢀ6$9(ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ&$1&(/ꢀ

Note: 1: If you need to record all day long, set SLOT1 as 00:00-24:00

& state is on; set SLOT2 as off. 2: When setting time in WEEK,

several days can be set at the same time.

When Reviewing a certain channel’s timing, only the current day will

be highlighted.ꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

,0$*(ꢀ6(77,1*

ꢀ

In CH option select the related channel. In MODE there are CBR

Image

MODE CBRꢀꢀ AV

FRAMERATE REAL

BITRATE 1024K

VIDEO LOSS OFF

COVERED OFF

VIDEO SET DEFAULT

(audio/video) and VBR (audio/video). AV is audio and video

synchronization, Video is the mode without audio (when there is no audio input

use this way to save HDD space).When in CBR, Framerate is Real time, Bitrate

is the related maximum data flux. Use direction key to select the different

bitrates. When in VBR, Framerate 1f/s-25f/s are selectable. Video Loss on

means that alarm will be on when the video is lost, and also trigger the relay

device.

TITLE

01 ON

CYCLE

OFF

SAVE CANCEL

Select the relevant Camera in CH (this recorder has 8-Ch alarm input).

TYPE has NO (normal open) NC (normal close) output modes. If the

Camera number in RECORD is selected, recording would be started for that

Camera automatically when there is alarm input. If the alarm output port is

chosen, it will trigger the corresponding relay when there is an alarm input.

DELAY means to extend the recording time after receiving alarm signal

clears.10, 20, 30 ĂĂ90SEC delays. When the outside alarm is cleared, the

system will extend the recording time automatically before closing alarm and

relay output. When Time 1 or Time 2 are on, if an alarm occurs within the time

of these settings, the recording will be triggered by alarm signals. The beginning

time should be earlier than the ending time. The setting in Time 2 should be

later than the setting in Time 1. ALMSVR IP is used to transmit the alarm signals

to the designated IP server.

Alarm

$/$50ꢀ6(77,1*ꢀ

ꢀ

&+ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢂꢀ

7<3(ꢀꢀꢀꢀꢀꢀꢀꢀ12ꢀ

5(&25'ꢀꢀꢀꢀꢀꢀꢂꢀꢋꢀꢉꢀꢅꢀ

$/0287ꢀꢀꢀꢀꢀꢀꢂꢀꢋꢀꢉꢀ

$''5ꢀꢀꢀꢀꢀꢀꢀꢀꢄꢄꢌꢀ

'(/$<ꢀꢀꢀꢀꢀꢀꢀꢃꢄ6(&ꢀ

7,0(ꢀꢂꢀꢀꢀꢀꢀꢀꢄꢌꢐꢄꢄꢀ$0ꢀ̢ꢀꢄꢌꢐꢄꢄꢀ30ꢀ

67$7(ꢀꢀꢀꢀꢀꢀꢀ2))ꢀ

7,0(ꢀꢋꢀꢀꢀꢀꢀꢀꢄꢌꢐꢄꢄꢀ$0ꢀ̢ꢀꢄꢌꢐꢄꢄꢀ30ꢀ

67$7(ꢀꢀꢀꢀꢀꢀꢀ2))ꢀ

$/0695ꢀꢀꢀꢀ,3ꢀꢀꢂꢊꢋꢍꢂꢃꢌꢍꢄꢄꢄꢍꢂꢂꢑꢀ

ꢀꢀꢀꢀ6$9(ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ&$1&(/ꢀ

Select the corresponding channel in CH, and choose the protocol

Pan-tilt control

3$17,/7ꢀ&21752/ꢀꢀ

ꢀ

of the brand name of the corresponding pan-tilt decoder in

&+ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢂꢀ

35272&2/ꢀꢀꢀꢀꢀꢀꢀ121(ꢀ

%$8'5$7(ꢀꢀꢀꢀꢀꢀꢀꢂꢋꢄꢄꢀ

$''5(66ꢀꢀꢀꢀꢀꢀꢀꢀꢄꢄꢄꢀ

ꢀꢀꢀꢀ6$9(ꢀꢀꢀꢀꢀꢀꢀ&$1&(/ꢀ

ꢀꢀ

PROTOCOL. ADDR is the address of the corresponding PTZ Camera.

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

ꢂ

IP is set by using pq or input the exact numbers to change

the IP address. IP address setting can only be here. The related

SUBNETMASK and GATEWAY should be set according to the IP

Network

1(7:25.ꢀ6(77,1*ꢀ

ꢀ

,3ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢂꢊꢋꢁꢂꢃꢌꢁꢄꢄꢄꢁꢂꢅꢂꢀ

68%1(70$6.ꢀꢋꢎꢎꢁꢋꢎꢎꢁꢋꢎꢎꢁꢄꢄꢄꢀ

*$7(:$<ꢀꢀꢀꢀꢂꢊꢋꢁꢂꢃꢌꢁꢄꢄꢄꢁꢄꢄꢂꢀ

:(%ꢀ3257ꢀꢄꢄꢄꢌꢄꢀ

7&3ꢀ3257ꢀꢀꢀꢀꢉꢑꢑꢑꢑꢀ

021,725ꢀꢀꢀꢀ7&3ꢀ

3/$<%$&.ꢀꢀꢀ7&3ꢀ

ꢀ

ꢀꢀ6$9(ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ&$1&(/

address. MONITOR and PLAYBACK can be changed by using

pqTCP/IP or MULTICAST. Save the setting in SAVE, and restart the

recorder.

Note:

MULTICAST: The users with Admin levels can monitor each channel

freely. All other users can only view after Admin

releases camera. 5 users at maximum.

TCP Protocol: All users are able to monitor any channel. User shall

select Camera # desired. If the transmission is over

Internet, TCP should be chosen. 2 users can log in at a

maximum.

Select the Camera channel in CH. Open or close (On/Off)

Motion detection

the function in STATE. Choose how long you want to

continue the recording (10, 20, 30, ……90SEC) when motion is detected

and then cleared. ALMOUT controls the alarming state for motion

detection. SENS has three levels: LOW, MID, HIGH. AREA can be

accessed by pressing ENTER. The setting area can be divided in 192

sections. Red section means the current cursor position, and the blue

section is the motion detection area. Areas with no color are no motion

detection areas. Press Fn to locate the current section, then move the

cursor to cover the MD area needed; press Fn again to choose the MD

area. Press pq to get the setting and press ENTER to confirm.

027,21ꢀ'(7(&7,21ꢀ6(783ꢀ

ꢀ

DELAY

30 SEC

ALMOUT OFF

SENS

MID

SET

AREA

SLOT1

SLOT2

08:00AM – 08-00PM ON

08:00AM – 08-00PM OFF

SAVE

CAMCE;

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

$'0,1ꢀ6(77,1*ꢀ

ꢀ

6.4.4 Admin setting

Menu of Admin setting is pictured at Right:

ꢀ

Password

Select GUEST and MANAGE. Press pq or the number

key to change the password, then confirm the change by

inputting the password again. Press ESC to go back to the sub

menu. Only ADMIN level user can change the password.

3$66:25'

ꢀ

*8(67ꢀꢀꢏꢏꢏꢏꢏꢏꢀ

&21),50ꢀꢏꢏꢏꢏꢏꢏꢀ

0$1$*(ꢀꢀꢏꢏꢏꢏꢏꢏꢀ

&21),50ꢀꢏꢏꢏꢏꢏꢏꢀ

SAVE

CANCEL

File delete

Others

Used to clear the data in the HDD. Be careful with this item.

DATA DEL

PASSWORD: _______

Before you delete the data, you have to input the manage password.

During Alarm tip on, when there is alarm input from outside,

the alarm information window will pop up. If Shutdown pwd is on,

you need to input the right manage level password before turning

off the DVR; if it is off, 4 seconds after pressing on the power

button the DVR will turn off. Output x o point and Output y

point are set for the starting point of the window on the screen,

and Playback height is to set the window height during

playback. The user can set the starting point of the monitor

screen and the size of the monitor screen and the playback

screen.

27+(56

ꢀ

ALARM TIP

SHUTDOWN PWD

OUTPUT X/Y POINT

OFF

000/000

PLAYBACK HEIGHT 480

AUDIO MODE

TITLE COLOR

MONITOR OSD

PCM

WHITE

8KHZ

MAINTENACE WEEK S M T W T F S

MAINTENACE TIME 12:00 AM

SAVE CANCEL

Press pq to get the setting and press ENTER to confirm. After the

default setting is selected, system will restore the original Factory

Default settings.

'()$8/7

ꢀ

Default

ꢀ

LOAD DEFAULT CONFIGURES?

YES NO

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

6.4.5 Backup

Menu of Backup is Pictured at Right:

Backup records

Move the cursor to select the backup device, channel

number, backup speed, starting data and time, ending date and

time, and then select to start the backup, and system will display

the backup processing. If the user does not connect the backup

device correctly, the system will display: No backup disk; if the

device is full, it will display: Disk is full. During the backup, it

will display the time. For the backup device you can choose

among HDD/USB/CDR. If HDD is chosen as the device, the

backup speed can be selected between Fast and Normal. If the

backup speed is Fast, system will stop the current recording.

%$&.83ꢂ5(&25'6ꢂ

%$&.83ꢂ'(9,&(ꢀ &'5ꢂ

&+ꢀ ꢂꢂꢂꢂꢈꢂ

%$&.83ꢂ633('ꢀ )$67ꢂ

67$57,1*ꢂ'$7(ꢀ ꢀꢉꢉꢃꢊꢃꢊꢈꢆꢂ

67$57,1*ꢂ7,0(ꢀ ꢋ˖ꢈꢆ$0ꢂ

(1',1*ꢂ'$7(ꢀ ꢀꢉꢉꢃꢊꢃꢊꢈꢆꢂ

(1',1*ꢂ7,0(ꢀ ꢈꢉ˖ꢈꢆ$0ꢂ

%$&.83ꢀ ꢂ$''ꢂꢀ 67$57

Delete backup

Select the backup device you want to delete the records from

first, and then confirm the deletion by selecting

DELETE BACKUP

DEVICE HDD

ꢂ

DELETE CONFIRM

6.4.5 LOGOUT

Press ENTER to logout . To enter the menu again , password

is needed.

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Chapter 5 Operation Over Networkꢂ

There are two ways to access the DVR over the network: Using Microsoft Internet

Explorer(IE) or Mace Remote Client Software.

Using IE, no special software needs to be installed on the PC. A web control unit will be

downloaded to the computer automatically the very first time a connection to DVR is

initiated.

The Mace Remote Client Software needs to be installed properly to use the second

option. But the graphical user interface menu items are identical. Goto

http://www.mace.com/, under Support, download the Remote Client software.

1. Setting up the Client End

2. Login and Logout

3. Operation of the Right Click Menu Items

4. Record Search

5. System Configuration

6. Assistant

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

1. Setting up the client end

No special software is needed to install on the DVR, PC or other devices in order to access DVR using the IE

browser. If the IE responds back “Page Cannot Be Displayed” or “Server not Found”, check your network

connection carefully.

2. Login and logout

Please input the IP address of the DVR in the address column of the browser. Take the DVR’s IP address:

192.168.0.168 as an example: Input http://192.168.0.168. Note: The first time you visit this DVR the system

will pop up the dialogue box to ask whether you accept ActiveX or not, and please choose Yes, then the

system will install the software automatically.

ꢀ

On the remote monitor display, there is a monitor video window, with selection choices: loginǃlogoutǃsearch,

config(system setting)ǃAssistant(assistant setting) and so on.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

ꢀ

Input the username and password. There are three types of Users: Administrator, User, and Guest. For

detailed information please refer to User manage ⱘ in Assistant setting. The default username is admin, & password

is admin. For Security purposes, please change the administrator password.ꢀ

If after the input of the username and password, the following box pops up(6-3). The system is indicating that some other

user has used this name and is logged in. Please use another name to log in.

If after the input of the username and password, the following box pops up. The system is indicating that the name or

Password input is incorrect, and to please try again.ꢀ

ꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Log out: If the logged in user needs to log out, please click logout button. The popup dialogue box appears. Please

choose Yes. See 6.5.

ꢀꢃꢍꢎꢀ

3. Operation of the Right Click Menu Items

After you log in as Administrator, the buttons like login, logout, search, config & Assistant are activated. Click the right

mouse key and the following interface Display:ꢀ

ꢃꢁꢃꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

ꢀ

If the DVR is 8 Channel, the real-time monitor will show 8 channel options; if 4 channel, it will show 4 channel options.ꢀ

The right key menu includes: Real time monitor, Playback control bar, Pan-tilt control, Set volume, Net data flux,

Full screen, Resize video and so on.ꢀ

Real time monitor Among the displayed channels,(6-7)you may select the channel you want to see.

ꢃꢁꢑ

ꢀ

Playback control bar Please refer to Records playback.

Pan-tilt control The Arrows Control the moving direction of the pan-tilt and the zoom, iris & focus of the lens.

See 6.8. Press the related buttons to control. Note: Before the PTZ will operate you must set the correct protocol of

the pan-tilt on the DVR configuration menu.

ꢃꢁꢌꢀ

ꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

ꢀ

Set volume Audio volume is User selectable.. User can drag the bar to adjust or select Mute to cancel the sound.

ꢃꢁꢊꢀ

Net data flux Display the statistics of the network transmission data flux. When there is no network data

transmission the statistics shows zero.ꢀ

ꢀ

Full screen There are two ways to view full screen monitor: One is to double click the window directly; the other

is to select Full screen among the right click menu items. During multi-window state, choose one of the windows

and double click it for full screen display.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

4. Records Search and Playback

Click on search, then fill in the required info on the pop up dialogue box for the records search.

6-11

Input recording time, channel number and searching type: Record or Alarm search, and the results will display

in the dialogue box. It displays 15 records from search time and forward. Click Pageup and Pagedown to

select the desired records. Double click the desired record, and system will play the selected record, which

can be played at full screen. At the same time you can also perform a record download, and the record will be

automatically be saved at C:\Download.

Save record

stop save

capture picture

full screen

During the playback, you can operate the buttons in the playback bar such as: save record, stop save, capture

picture, fast play, pause, full screen. During the playback on the video screen, the video can indicate the

channel number, time and data flux of the record.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Download See 6-12, select the desired record and click Download.

6-12

The software supports the downloading of several records simultaneously. The default format of the

downloaded records’ name is: file name, Channel # , date, time, extension name is .mp4(Example:

a-0120021205071028.mp4, 01 means channel 1, 20021205 means December 5^thof 2002, 071028 means 7

o’clock 10 minutes 28 seconds).

6-13

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

To Save a File located in the Search Record Display, Select File, press the Download button. A Save Window

opens. Input the file name and choose Save. The screen shows the processing of the downloading until the

completion.

6-14

5. System Configuration

Click Config button and a pop up the dialogue box appears. There are GeneralǃTimingǃImageǃAlarmǃ

Motion Detection tabs of the five menu configuration screens.

Note: The grayed part of the menus that cannot be changed, can only be modified directly at the DVR.

General: Include the recording length setting. In Control Column select the channel number and its PTZ

decoder’s protocol, as well as the related address for the control of the PTZ Camera.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Timing 6-16 Allows the User to select the different channels and dates to perform the manual recording and 2

different periods of time. The set time in Time 1 and Time 2 are independent with the set time in Motion

detection. There is no week setting for Motion detection.

Timing of motion detection: User can set two time periods of the motion detection, time and the state of the

motion detection so as to activate the recording during the time period. Only when Motion Detection is On,

the set time period takes effect. If the state of the two time periods are both Off, the system will not record

in motion detection.

6-16

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Image With this menu, adjustments can be made for image quality and protocols of each channel.

ꢃꢁꢂꢑꢀ

Style: Among the options of the coding styles there are: VBR(variable baud rate), CBR(consistent baud rate),

f/10s, f/5s, f/2s, 1f/s, 2f/s, 3f/s, 4f/s, 5f/s, 6f/s, 8f/s, 10f/s, 12f/s, 15f/s & 20f/s. Select one of the styles and

save. For VBR and selectable frames there are 1, 2, 3, 4, 5 & 6 level of image quality. Please choose the

desired level.

ꢀꢃꢁꢂꢌꢀ

ꢀ

Level 1:data flux 128Kb/S, Level 2: 256Kb/S, Level 3: 384Kb/S, Level 4: 512Kb/S, Level 5: 768 Kb/S, Level

6: 1Mb/S.

The different data flux demands on the related bandwidth and the transmission image quality is also different.

Among them, Level 6 demands on the highest bandwidth and has the best image quality.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Net transmission Protocol- There are TCP and Multicast (two types). Multicast protocol: the 1^stuser logged

in can control power, can view the image at will and other users can only follow this user to view the image. 5

users are allowed to view at the same time. TCP protocol: each user can view the image at will. According to

the need, users can choose between different protocols. If viewing is through the Internet you must choose

TCP. Up-to 5 users are allowed to view at the same time.

Alarm When there are alarm input signals, the user can select the recording channel and the output port for

the actual need.

6-20

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Motion detection When the user sets the time period for Motion Detection, the motion detection will take

effect. The blue area is the selectable motion detection area. The User can move the dialogue box to choose

the correct area and can also set the sensitivity of the area due to the need. Click Full screen or press right

key on the area to display the motion detection area in full screen mode. After setting the area the user can

Save channel or Clear the area. The Alarm output field allows you to activate an output relay. The default

port is 2. If you want to set this channel fully as motion detection recording, you have to turn off the timing

recording of this channel.

6-21

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

6. Assistant

Assistant Click on Assistant setting, as following, there are User manage - Record control - Apply for

control right - Log information - System information - Channel name - Upgrade BIOS, etc.

6-22

User manage: displays the user(Log-In) information of the DVR. The buttons to the right can let an admistrator

user save, add, modify, delete and cancel the information.ꢀ

Three levels of users types: Administratoṛ̣fully set the system, modify & Use the system.; Useṛ̣can

not set system parameters or modify other users’ information. This User can select and Operate existing

programming; Guesṭ̣can not set system parameter and records search, can only modify personal

information.ꢀ

ꢀꢃꢁꢋꢉꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Add˖Click Add to show the following dialogue box˖

ꢃꢁꢋꢅꢀ

The Admin User can add user information in this dialogue box, select your power. Note: There is only one

administrator allowed.

Modify˖Select this button to show the following. User can modify the filled-in information.

ꢃꢁꢋꢎꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Record control˖Manually control the recording of each channel.

6-26

Apply for control power˖Web client software can supply the login of multiple users. If you want to have the

control, you can click this option and confirm to have the control. (6-27). If a new user wants to have the

control, the new user has to apply and gain the authorization of the existing user with control . If the logged-in

users are all normal users, the first logged-in user gains the control power automatically. If a higher lever user

logs in later, they can gain the control power automatically. If only one user logs in or the logged-in user is

the user with control, the box is gray.

ꢃꢁꢋꢑ

ꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

ꢀ

The picture below (6-28) is the other user sending request to the existing user with control.

ꢃꢁꢋꢌꢀꢀ

ꢀ

ꢀꢀꢀꢀ

Log information˖The operations on the system are all recorded in log information.

ꢃꢁꢋꢊꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

System information˖Check the basic information of the system. When sound is not needed, you can turn

off the audio. Due to the bandwidth considerations, the user can select the different Video transport modes,

Video type PAL or NTSC has to be selected correctly, 110vac, 60hz is normally NTSC, 220vac, 50hz is

normally PAL. If Auto recycle monitoring is on, system will sequence between all the channels

automatically with a user selectable dwell time. Net data flux˖during real-time monitor will display the

statistics of the network data flux.

ꢃꢁꢉꢄꢀ

ꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Channel name˖Cameras can be be named for each channel. No more than 12 Characters. The revised channel

names will be displayed on the screen. The default setting of the channel name is Channel No.1 thru Channel

No.8.

ꢃꢁꢉꢂꢀ

ꢀ

Upgrade BIOS˖ Administrator can upgrade the BIOS program remotely. A Browse window will pop up for

File Information. Open the related BIOS or Web file˄example: DVR0800.BIN or Multi-webfile.bin, and click

on Send. After the upgrading, system will automatically reboot to take on the new system software.

6-32

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

About˖Version information – This palette displays information about the DVR and may be vital when

contacting MACE Support.ꢀ

ꢀꢀꢃꢁꢉꢉꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Chapter 6

System Connections

ꢈꢁ DVR Rear Viewꢂ

ꢀꢁ RS232 Port Connectionꢂ

ꢃꢁ 25 PIN Alarm Transfer Boxꢂ

ꢄꢁ RS-485 Port Connectionꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

1. DVR Rear View

1- Alarm – RS485 (DB-25)

4- Power Switch

2- Audio Out (BNC)

5- Power Plug-in

8- USB port

3- Audio In (BNC)

6- RS232 (DB-9)

9- RJ45 (10 Base-T)

7- VGA out (HD-15)

10- Video Out (BNC)

11- Video In (BNC)

Network connection note: When connecting directly to the network card of a computer, please use CAT-5

Crossover Cable; when connecting to a LAN or Router use CAT-5e cable.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

ꢂ

ꢂꢂꢂꢂ'95ꢈꢇꢉꢄ5:ꢂ5HDUꢂ9LHZꢂ

1ǃpower switch 2ǃpower plug 3ǃ220V/110V shift switchꢀ 4ǃRS232 connection

5ǃVGA connectionꢀꢀ 6ǃAudio inputꢀꢀ

7ǃUSB portꢀꢀ

8ǃ1394 connection

9ǃNET network connection˄RJ45˅ꢀꢀ

10ǃAudio outputꢀꢀ

11ǃVedio output

12ǃ$ODUPꢁ56ꢅꢌꢎꢀconnection

13ǃVedio input 14ǃVedio input 15ǃAlarm output

16ǃAlarm output & control connection 17ǃAlarm inputꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

2. RS232 Port Connection

ꢀ

Note: The connection for DVR system software upgrading or debugging through the serial port

The connection for dial-up login through MODEM

ꢀꢀꢀꢀꢀ7KHꢀFRQQHFWLRQꢀIRUꢀ'95ꢀFRQWUROꢀWKURXJKꢀNH\ERDUGꢀ

ꢀ

3ꢍꢀ25 Pin Alarm Transfer Box

Connect 25 pins of the transfer box directly with the 25 pins alarm input output connection of the DVR

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Fasten the transfer box on the back panel of DVR with two screws

Pull out 6 connection terminals of the transfer box, corresponding connection marks can be clearly noticed.

Connect function line according to connection marks

ķꢀ Loosen the screws on the connection terminal;˄connection diagramķ˅

ĸꢀ Insert lines needed to corresponding terminals ˗˄connection diagramĸ˅

Ĺꢀ Fasten the screws on the terminals after insertion of the lines.(connection diagramĹ˅

connection diagramķ

connection diagramĸ

connection diagramĹ

Notes:

a) “Ground”˖ground line˗

terminal

b)“+12v”˖provide the power to alarm device

with current less than 2A

c)“OUT 1ǃ2” is two alarm outputs switch.

Nomal open type˗

d)Ā485 AǃBā is communication connection,

used to connect such recorder control device

such as control decoder

eĀ) +12˄C˅” is control power output, is used for

standby power for smoke sensor alarm device..

dismiss of the alarm needs the device to turn off

the power.

screw

f)ĀALARMIN 1…8˅ is alarm input. High level voltage input. Input

voltage is 6-24V˄12V is recommended˅Ǆ

10-Pin connection for DVR1604RW

If you want to control pan-tilt, lens and process the relay of the alarming signals by the DVR, the 10-pin port can realize. The

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

four 10-pin port can control various pan-tilt decoders, and the specific type of the decoder can be selected from the Control of

the System setting in the menu. On plug the foot’s serial number is marked.

A: Alarm input: ALARM1~ALARM8

B: Alarm input: ALARM9~ALARM16

C: Alarm OUTput: ALARM1~ALARM5

D:ALARM6 output and 12V controllable pressure AB line port

ꢀ

4. RS-485 port connection

If you want to control Camera pan-tilt-zoom (P/T/Z) or activate the DVR Output relay, the 25-pin RS485

connection must be used. See detail below.

The RS485 port connection can control various (P/T/Z) Cameras, and the specific model or protocol can be

selected from the Control Menu in System settings.

The DB25 pin outs are marked below. The definition of the pin outs are as follows: The broken line in the

graph indicates inside connection˅

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Alarm input ALARM 1

7KUXꢀ

Alarm output

ALARM 8

ALARMOUT1

ALARMOUT2

Controllable +12V output

120¡ End of Line

Combined as RS485 B line

Combined as RS485 A line

+12V output

(EOL)

resister

required.

Decoder

Gnd

a) Pins 1,14,2,15,3,16,4,17 connects to alarm input: ALARM1~ALARM8

b) Pins 5 & 18 = OUTPUT Relay 1 - 6 & 19 = OUTPUT Relay 2 Each Relay (normally open):

c) Pins 7&20 = OUTPUT 3 is a controllable +12V output.

d) Pins 8, 9 & 21 are +12V power output, Use for Low current items only such as Relays and Alarm Devices.

e) Pins 10 & 22 are the B line of RS485, Pins 11 & 23 are the A line of RS485;

f) Pins 12, 13, 24 & 25 are Ground (Gnd).

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

- Connection of the alarm input:

Pwr Supply, Alarm Device and DVR connection

Alarm Device

ꢀ

+12V

GND

Com

ꢀ

Typical

ꢀ

ƼALARMIN

connection to

DVR alarm in.

gInstruction of the alarm

input end:

ƼGNDꢀ

ꢀ

channel alarm

ꢒꢂꢋ9ꢀꢀꢀ*1'ꢀ

3ZUꢀ6XSSO\ꢀ

inputs with NO or

NC alarm(normally

open or normally

close type). The power out of the alarm sensor can be provided by the DVR(Low current only) or (External

alarm power supply)

·Instructions for alarm device power from DVR:

N/O or NC alarm outputs refer to information below..

·Instruction of the controllable +12V

Available for Low Current Power to Alarm devices.

·Instruction of RS485 A & B line:

Used to connect the A and B line of the PTZ units.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

·Module sketch of the alarm input end

·Module sketch of the alarm output end

gRelays’ parameter of the alarm output end

Model: G6H

Relay Material

Silver

Rating, resistance & Rated switch capacity

30VDC 1A, 125VAC 0.5A

62.5VA 33W

load.

Maximum switch power

Maximum switch voltage

Maximum switch Current

Pins with same polarity

125VAC, 110VDC

Insulation

750VAC 1minute 50/60Hz

1000VAC 1minute 50/60Hz

1500V (10h160us)

3ms max

pins with different polarity

between relay and loop

Surge voltage

between relays with same polarity

Length of open time

Length of close time

Longevity

3ms max

Mechanical

Electric

100h106 ⃵ (10Hz)

200h103 ⃵ (0.5Hz)

-40~+70ć

Temperature

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Chapter 6

Serial Port Operations

ꢈꢁ System Settingꢂ

ꢀꢁ Software Upgradeꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

1ˊ System Setting of the Terminal

The system’s operation can also be controlled through the RS232 port. The specific operation is as follows: First, copy

“Terminal” and new DVR system software to the computer. Connect the computer with the DVR via the RS232 port. Run

“Terminal” program and create the connection between the computer and the DVR.

The settings information for the connection is: Baud rate— 115200bps

Data bit— 8 bits

Stop bit— 1 stop

Check — no parity

Control on data flow— noꢀ

You can log in by username admin (default user with administrator ) for the serial port login.

Press any key to enter the login interface which displays the following:

Username: admin

Input the name; press the “enter” key. Then, input the password as follows:

Password: admin

If the username and password are correct, the system will allow entry via the serial port. The detailed

functions are the same as the menu setting.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

2. Serial port upgrading operation

After connecting with the above operations, please continue with the below operation:

Press any key to enter login interface as following:

Username - admin

Enter username and press Enter. Enter the password as follows:

Password - dahua

System enters into DEBUG state, and input BIOS.

Press Enter.

Click Communication in the menu Field——Send file, and open upgrading program file

(DVR0804_NTSC.BIN—8 Channel DVR BIOS program, please complete this operation within 20 seconds,

otherwise a Time out occurs). System begins to upgrade automatically and after the upgrading is completed, a

system reboot will occur.

ꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Appendix 1

Remote Control Unit

Remote controller – Operates like On-Screen Buttons

ꢂ

1. Address

2. Multi Screen

6. Enter/Menu

3. Camera Select

7. ESC (Cancel)

11. Jump Backward

15. Play/Pause

4. Record

5. Function Key

9. Jump to Next

13. Next Selection

8. Direction Arrows

12. Stop

10. Previous Selection

14. Reverse

16. Fast Forward

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Appendix 2

Frequently Asked Questions

1. After Power up, “No HDD” message is flashing on the local monitor

This is an indication that either the harddisks are not installed correctly or no harddisk is installed at all. Refer to

Appendix 2 Hard disk installation. Also inside the DVR there is a yellow sticker with instructions on harddisk

installation.

2. When I power down the DVR, why do I have to press and hold the power button for 4 seconds?

First of all, using the front orange power button to shut down the DVR will make sure the DVR properly finish and

close all it operation and file system, thus eliminate many possible causes for harddisk errors leading to data loss.

This is the correct way of powering down a DVR.

Secondly, requiring holding the button for over 4 seconds is to avoid accidental shutdown of the DVR due to

unintended touch of the button. You can make the shutdown more secure (i.e. avoid unauthorized shutting down)

activating

the

shutdown

password

protection

feature.

(MENU->ADMIN

SETTING->OTHERS->SHUTDOWN PASSWORD)

3. What does the sound of the buzzer mean when normally starting the machine

When the machine is started successfully, it will tone out a short ring.

When the HD can not be identified, it would tone out a longer ring.

When communication with the controller panel is abnormal, it sends out a tone of one long ring and two short in

series.

4. Can I control the recording time?

The recording time unit is per day. Besides timing recording, there are other recording methods such as motion

detection recording, manual recording, external event triggering recording. Confirm that each of the settings is

correct.

5. The indicator light is flashing while recording˛

Check the external video input signal first. Such phenomena would happen when the input signal is not

standard. If it is not the input signal, it must be caused by that the reading speed of the HD is too slow. In this

situation, the current HD should be changed.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

6. Why the screen is black after I switch off and on the power?

The power supply comes with the DVR has a built-in protection mechanism. After the power is shut down, you

have to wait for at least 5 seconds before turn it on again. Turn off the power, wait for 5 seconds, and turn it on

again. If this does not correct the problem, contact your Mace technical support hotline.

7. What kind of external equipment could be connected to the Recorder?

It can work together with various matrix units, multiplexers, switchers, quads and PTZ Domes.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

Appendix 3

Hard Disk Installation

Hard disk installationꢂ

There is one 80G hard disk (HD) preinstalled in the Mace DVR, unless you ordered a special configuration. So

normally you DO NOT have to go through these steps. This procedure only applies to cases where there is no

built-in hard disk in the DVR or additional hard disks need to be installed.

In total, a maximum of 8 large capacity hard disks can be installed inside the machine if a CD burner is not

needed. With a CD burner, there can be a total of 5 internal large capacity hard disks. User can decide the

number of hard disks according to required image quality, recording time and recording length.

Installation stepsꢀ

ꢀ

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

ꢀ

ꢀꢀ

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

ꢀ

Dismantle the top cover,

Dismantle the HD

Separate the up and

ꢀ

Install HD

open the cabinet

bracketꢀ

down part of the bracket

ꢀ

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

Set the master-slave jumper wire

(refer to the clue on the back of the

HD)

Combine the two parts of

the bracket

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

Connect the HD bracket

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

ꢀ

ꢀ ꢀ

ꢀ

Connect HD data line to

IDE port

Plug in HD power line

Close the cover and install the screws

ꢀ

ꢂ

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DVR0404RW/DVR0804RW

Digital Video Recorder

LIMITED WARRANTY

Mace Security Products, Inc. (MACE) warrants to the original purchaser of this product that it shall be free of defects

resulting from workmanship or components fro a period of one (1) year from the date of sale. Defects covered by this

Limited Warranty shall be corrected wither by repair or, at MACE’s discretion by replacement. In the event of

replacement, the replacement unit will be warranted for the remainder of the original one (1) year period or thirty (30)

days, whichever is longer. THERE ARE NO OTHER ORAL OR WRITTEN WARRANTIES, EXPRESSED OR

IMPLIED, INCLUDING BUT NOT LIMITED TOTHOSE OF MERCHANTABILITY OR FINESS FOR A

PURTICULAR PURPOSE.

This Limited Warranty is nontransferable and does not apply if the product has been damaged by negligence, accident,

abuse, misuse, modification, or misapplication. To be eligible for warranty service, a defective product must be sent to

and received by MACE within twelve (12) months of the date of sale and be accompanied with proof of purchase. MACE

does not warrant that this product will meet your requirements; it is your sole responsibility to determine the suitability of

this product for your purposes. MACE does not warrant the compatibility of this product with your computer or related

peripherals software.

MACE’S SOLE OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR

REPLACEMENT OF A DEFECTIVE PRODUCT. THE MNUFACTUREER SHALL NOT, IN ANY EVENT, BE

LIABLE TO THE PURCHASER OR ANY THIRD PARTY FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES OR LIABILITY IN TORT RELATING TO THIS PRODUCT OR RESULTING FORM ITS USE OR

POSSESSION.

Operational Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

KTI Networks Switch KS 2260 User Manual
KWC All in One Printer KWC QBIX User Manual
LG Electronics TV DVD Combo 23LX1RV User Manual
LifeWise Washer 63 1530 User Manual
Link electronic Stereo Amplifier PVA 851 User Manual
Lochinvar Water Heater ARM3072PAB User Manual
LOREX Technology Security Camera SG7125 User Manual
Makita Cordless Sander 9227C User Manual
Mazda Automobile 2005 3 4 DOOR User Manual
Mellerware Carpet Cleaner 23810 User Manual