Pub. 988-0156-021
www.lowrance.com
GlobalMap 3300C
Mapping GPS Receiver
Installation and Operation
Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Sec. 1: Read Me First! ...............................................................1
Capabilities and Specifications: GlobalMap 3300C...................... 2
How Lowrance GPS Works .......................................................... 4
Introduction to GPS and WAAS................................................... 6
Free Training Aids Available....................................................... 8
Unit Emulator........................................................................... 8
How to Use this Manual: Typographical Conventions................ 9
Sec. 2: Installation & Accessories ........................................11
Preparations................................................................................ 11
GPS Antenna/Receiver Module.................................................. 11
GPS Module Installation ........................................................ 12
Connecting Directly to the Unit............................................. 14
Connecting to a NMEA 2000 Network................................... 15
Power Connections.................................................................16
Powering a NMEA 2000 Buss (NMEA 2000 Power Cable)....... 17
Powering your Unit (Power Supply Cable)................................ 17
NMEA 2000 Cable Connections................................................. 19
NMEA 0183 Cable Connections (Data Cable)........................... 20
Mounting the Unit: Bracket or In-Dash Installation................ 21
MMC or SD Card Memory Card Installation............................ 24
Face Cover................................................................................... 25
Other Accessories........................................................................ 25
Sec. 3: Basic GPS Operations................................................27
Keyboard ..................................................................................... 27
Power/Lights (Turn Unit On and Off) ....................................... 28
Main Menu.................................................................................. 28
Pages ........................................................................................... 30
Satellite Status Page .............................................................. 30
Navigation Page...................................................................... 32
Map Page................................................................................. 34
Background Map vs. Mapcreate Map Content............... 36
Resize Window Command .................................................. 38
Basic GPS Quick Reference..................................................40
Find your Current Position ........................................................ 41
Moving around the Map: Zoom & Cursor Arrow Keys.............. 41
Selecting any Map Item with the Cursor .................................. 42
Searching..................................................................................... 42
Set a Waypoint............................................................................ 45
Create Waypoint at Current Position ................................ 45
Create Waypoint on Map.................................................... 46
Create Waypoint by Entering a Position ........................... 46
Navigate to a Waypoint.............................................................. 47
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Man Overboard (MOB) Waypoint........................................ 48
Navigate Back to MOB Waypoint.............................................. 48
Navigate to Cursor Position on Map.......................................... 49
Navigate to a Point of Interest................................................... 50
Creating and Saving a Trail....................................................... 50
Displaying a Saved Trail ............................................................ 52
Navigating Trails........................................................................ 53
Visual Trailing ........................................................................ 53
Navigate a Trail (Forward)..................................................... 53
Navigate a Back Trail (Backtrack, or Reverse)..................... 56
Transfer Custom Maps and GPS Data Files............................. 56
Cancel Navigation....................................................................... 58
Sec. 4: Advanced GPS Operations .......................................59
Find Distance from Current Position to Another Location ...... 59
Find Distance from Point to Point ............................................. 59
Icons............................................................................................. 60
Create Icon on Map................................................................. 60
Create Icon at Current Position............................................. 60
Delete an Icon ......................................................................... 61
Navigate to an Icon................................................................. 61
Routes.......................................................................................... 62
Create and Save a Route ........................................................ 62
PC-Created Routes.............................................................. 62
Routes Created in the Unit................................................. 62
Delete a Route......................................................................... 65
Edit a Route Name.................................................................. 65
Edit Route Waypoints............................................................. 65
Navigate a Route..................................................................... 66
Navigate a Route in Reverse .................................................. 67
Trails ........................................................................................... 68
Delete a Trail .......................................................................... 68
Edit a Trail Name ................................................................... 69
Edit a Trail Color .................................................................... 69
Edit a Trail Pattern ................................................................ 69
Utilities........................................................................................ 70
Alarm Clock............................................................................. 70
Sun/Moon Rise & Set Calculator............................................ 70
Trip Calculator........................................................................ 70
Trip Down Timer..................................................................... 70
Trip Up Timer ......................................................................... 70
Waypoints.................................................................................... 70
Delete a Waypoint................................................................... 70
Edit a Waypoint (Name, Symbol or Position)........................ 71
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Waypoint .............................................................. 72
Set a Waypoint by Average Position...................................... 72
Set a Waypoint by Projecting a Position................................ 72
Sec. 5: System & GPS Setup Options...................................73
Alarms ......................................................................................... 73
Check MMC Files and Storage Space........................................ 74
Communications Port Configuration......................................... 74
Configure NMEA ........................................................................ 75
Coordinate System Selection...................................................... 76
Setup Loran TD....................................................................... 77
Map Fix ....................................................................................... 78
Customize Page Displays ........................................................... 79
Customize Satellite Status Page............................................ 79
Customize Navigation Page ................................................... 79
Customize Map Page .............................................................. 79
GPS Simulator ............................................................................ 79
Simulating Trail or Route Navigation ................................... 80
Initialize GPS.............................................................................. 81
Map Auto Zoom........................................................................... 81
Map Data..................................................................................... 82
Show Map Data....................................................................... 82
Pop-Up Map Information........................................................ 82
Map Boundaries...................................................................... 82
Fill Water with White............................................................. 83
Map Overlays (Range Rings; Lat/Long Grid) ........................ 83
Map Datum Selection ................................................................. 83
Map Detail Category Selection................................................... 84
Map Orientation ......................................................................... 85
Navionics Charts....................................................................... 86
Display a Navionics Chart:..................................................... 86
Port Information ..................................................................... 87
Tidal Current Information ..................................................... 88
Tide Information..................................................................... 90
Pop-Up Help................................................................................ 91
Position Pinning.......................................................................... 92
Reset Options.............................................................................. 92
Require WAAS ............................................................................ 93
Screen Contrast and Brightness ................................................ 93
Set Language .............................................................................. 95
Set Local Time ............................................................................ 95
Show WAAS Alarm..................................................................... 95
Software Version Information.................................................... 96
Sounds and Alarm Sound Styles................................................ 96
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Track Smoothing......................................................................... 97
Trail Options............................................................................... 98
Delete All Trails...................................................................... 98
Update Trail Option................................................................ 98
Update Trail Criteria (Auto, Time, Distance).................... 98
Trail Update Rate (Time, Distance)................................... 99
Delete Trail ............................................................................. 99
New Trail............................................................................... 100
Trail Visible/Invisible and Other Trail Options .................. 100
Transparency ............................................................................ 100
Units of Measure....................................................................... 101
Sec. 6: Searching....................................................................103
Find Addresses.......................................................................... 104
Find any Item Selected by Map Cursor................................... 107
Find Interstate Highway Exits ................................................ 107
Find Map Places or Points of Interest (POI) ........................... 110
Find Streets or Intersections.................................................... 112
Find Waypoints......................................................................... 116
Sec. 7: Supplemental Material............................................119
Index.........................................................................................125
WARNING!
A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD
TO OBTAIN POSITION INFORMATION.
CAUTION
When showing navigation data to a position (waypoint), a GPS unit will show
the shortest, most direct path to the waypoint. It provides navigation data to the
waypoint regardless of obstructions. Therefore, the prudent navigator will not
only take advantage of all available navigation tools when traveling to a way-
point, but will also visually check to make sure a clear, safe path to the waypoint
is always available.
WARNING!
When a GPS unit is used in a vehicle, the vehicle operator is solely re-
sponsible for operating the vehicle in a safe manner. Vehicle operators
must maintain full surveillance of all pertinent driving, boating or fly-
ing conditions at all times. An accident or collision resulting in damage
to property, personal injury or death could occur if the operator of a
GPS-equipped vehicle fails to pay full attention to travel conditions and
vehicle operation while the vehicle is in motion.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Read Me First!
How this manual can get you out on the road, fast!
Welcome to the exciting world of digital GPS! We know you're anxious
to begin navigating, but we have a favor to ask. Before you grab the
GlobalMap 3300C and begin installing it, please give us a moment or
two to explain how our manual can help you get the best performance
from your compact, color display, mapping GPS receiver.
First, we want to thank you for buying a Lowrance GPS unit. Whether
you're a first time user or a professional fisherman, you'll discover that
your GlobalMap 3300C is easy to use, yet capable of handling de-
manding navigation tasks. When you team your unit with our custom
mapping software MapCreate 6, you have an incredible combination.
You won't find another GPS unit with this much power and this many
features for this price!
Our goal for this book is to get you on the road fast, with a minimum of
fuss. Like you, we'd rather spend more time navigating and less time
reading the manual!
So, we designed our book so that you don't have to read the whole thing
from front to back for the information you want. At the start (or end) of
each segment, we'll tell you what content is coming up next. If it's a
concept you're already familiar with, we'll show you how and where to
skip ahead for the next important topic. We've also made it easy to look
up any tips you may need from time to time. Here's how:
The manual is organized into 7 sections. This first section is an intro-
duction to Lowrance GPS. It tells you the basics you need to know be-
fore you can make the unit look around and tell you where you are.
Section 2 will help you install your unit and the GPS antenna module.
We'll show you how to get the MultiMedia Card (MMC) correctly installed
inside the unit. We'll also tell you about some of the available accessories.
Section 3 covers Basic GPS Operation. It will show you how easy it is to
run the GlobalMap 3300C, right out of the box. This section features a
one-page GPS Quick Reference. (If you've already jumped ahead
and figured out how to install the unit yourself, and you just
can't wait any longer, turn to the Quick Reference on page 40
and head for the road with your GPS unit!)
Section 3 contains short, easy-to-scan GPS lessons that follow one an-
other in chronological order. They're all you'll need to know to find your
way on the water or in the wilderness quickly.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
After you've learned the basics (or if you already have some GPS expe-
rience), you may want to try out some of the GlobalMap 3300C's many
advanced navigation features. That brings us to Section 4, Advanced
GPS Operations. This section contains the rest of the unit's GPS com-
mand functions, organized in alphabetical order.
When you come to a GPS menu command on the GlobalMap 3300C's
screen, you can look it up in the manual by skimming over the table of con-
tents, just flipping through Section 3 or scanning through the command
portion of Section 4.
This unit is ready to use right out of the box, but you can fine tune and cus-
tomize its operation with dozens of options. We describe how to use general
system options along with GPS options in Section 5, System Setup and
GPS Setup Options. Section 5 is organized in alphabetical order.
In Section 6, we go into more detail on one of the GlobalMap 3300C's
most remarkable capabilities — Searching. We'll introduce a search
example in the Basic GPS Operation section, but there are so many
map items you can search for, we had to give this function its own sec-
tion in the manual! For example, did you know this unit can look up
business phone numbers, functioning as a virtual Yellow Pages? We’ll
show you how in Section 6.
Finally, in Section 7, we offer Supplemental Material, including a list of
the GPS datums used, warranties and customer service information.
Now, if you're into the fine details, glance over the next segment on speci-
fications to see just how much GPS power your GlobalMap 3300C con-
tains. It's important to us (and our power users), but, if you don't care how
many watts of power the unit has, or how many waypoints it can store,
skip ahead to important information on how our GPS works, on page 4.
Capabilities and Specifications: GlobalMap 3300C
General
Display:............................ 1/4 VGA color, transflective TFT display; 5.0"
(12.7 cm) diagonal viewing area.
Resolution:...................... 320 pixels (vert.) x 240 pixel (horiz.) resolu-
tion; 153,600 total pixels
Backlighting:...................Color backlit screen and keypad for night use.
Input power:................... 10 to 15 volts DC.
Current drain: ............... With lights on: 700 ma.
Case size:......................... 5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6
cm); sealed and waterproof; suitable for
saltwater use.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
MMC slots:...........................One with waterproof door (SD card compatible).
Recording:........................GPS uses MMC & SD cards for recording trip
details and displaying charts or custom maps.
Back-up memory:.......... Built-in memory stores GPS data for dec-
ades. User settings are stored when unit is
turned off.
Languages:...................... 10; menu languages selectable by user.
GPS
Receiver/antenna:............External; LGC-2000 12 parallel channel
NMEA 2000-ready GPS/WAAS re-
ceiver/antenna.
Background map:.......... Built-in custom, detailed Lowrance map.
Contains: enhanced detail of continental U.S.
and Hawaii. Includes more than 60,000 nav
aids and 10,000 wrecks/obstructions in
coastal and Great Lakes waters. Metro ar-
eas, selected major streets/highways and in-
terstate exit services details included.
Custom mapping:.......... MapCreate 6 software optional; optional
LEI FreedomMaps offer the same high-
detail without the work of MapCreate; Navi-
onics charts on MMC cards optional.
Mapping memory:............More than 256 MB on one MMC (or SD) card.
Position updates: .......... Every second.
Position points: ............. 1,000 waypoints; 1,000 event marker icons.
Audible alarms: ............. Arrival/off-course/anchor.
Graphic symbols for
waypoints or event
marker icons:................. 42.
Routes:............................. 100; up to 100 waypoints per route.
Plot Trails:...................... 10 savable; up to 9,999 points per trail.
Zoom range:.................... 40 ranges; 0.02 to 4,000 miles.
NOTE:
The above memory capacities refer only to the unit's on-board mem-
ory. The amount of GPS data you can record and save for recall later
is only limited by the number and capacity of MMC cards you have.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE!
The storage and operation temperature range for your unit is from -4
degrees to +167 degrees Fahrenheit (-20 degrees to +75 degrees Cel-
sius). Extended storage or operation in temperatures higher or lower
than specified will damage the liquid crystal display in your unit. This
type of damage is not covered by the warranty. For more information,
contact the factory's Customer Service Department; phone numbers are
listed on the last page.
How Lowrance GPS Works
You'll navigate faster and easier if you understand how the unit scans
the sky to tell you where you are on the earth — and, where you're go-
ing. (But if you already have a working understanding of GPS receivers
and the GPS navigation system, skip on ahead to Section 2, Installation
& Accessories on page 11. If you're new to GPS, read on, and you can
later impress your friends with your new-found knowledge.)
First, think of your unit as a small but powerful computer. (But don't
worry — we made the units in this series easy to use, so you don't need
to be a computer expert to find your way!) The unit includes a keypad
and a screen with menus so you can tell it what to do. The screen also
lets the unit show your location on a moving map, as well as point the
way to your destination.
This gimbal-mounted unit uses an external antenna/receiver module,
which makes the whole system work something like your car radio. But
instead of your favorite dance tunes, this receiver tunes in to a couple of
dozen GPS satellites circling the earth. (It will also listen in to the
WAAS satellites in orbit, but more about that in the upcoming segment
introducing you to GPS and WAAS.)
Your unit listens to signals from as many satellites as it can "see" above
the horizon, eliminates the weakest signals, then computes its location
in relation to those satellites. Once it figures its latitude and longitude,
it plots that position on the moving map shown on the screen. The
whole process takes place several times a second!
The performance doesn't stop there. Stored in the permanent memory
of each GPS unit is a basic background map of the entire world. We lock
it in here at the factory — you can't change or erase this map.
The background map is suitable for many navigation chores, but for
maximum accuracy and much more detail, you need our optional map-
making software, MapCreate 6. Some unit features — such as
searching for businesses and addresses — won't work without a custom
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MapCreate map. There is so much detail in our background map (and
even more in MapCreate) that we'll describe their contents and differ-
ences in Section 3, Basic GPS Operations, on page 27.
Another portion of the unit's onboard memory is devoted to recording
GPS navigation information, which includes waypoints, event marker
icons, trails and routes. This lets you look back the way you came. Think
of this data storage like the hard drive memory in a computer or a tape
in a cassette tape recorder. You can save several different GPS data files,
erase 'em and record new ones, over and over again. Like any computer
file, these GPS Data Files (file format *.usr) can be shared between
other Lowrance GPS or sonar/GPS units, or even personal computers.
This unit has one more thing in common with a personal computer.
Just as computers have a floppy disk drive for storing and exchanging
files, the unit has a slot for an MMC (MultiMedia Card) or SD (Secure
Digital card) flash memory card. These solid-state memory devices are
about the size of a postage stamp, but can hold data ranging from 8 MB
to more than 256 MB in size. (Compare that to a floppy disk's 1.44 MB
capacity!) The unit uses all that MMC space for two key GPS purposes.
First, you can backup your onboard GPS Data Files by copying them to
the MMC. Since the MMC is removable (like a floppy disk or a cassette
tape), you can store these GPS Data Files on a personal computer
equipped with an MMC card reader. (Or store them on a pocketful of
MMCs, if you don't have a computer.) Our MapCreate mapping software
can save, edit or create its own GPS Data Files, which can be copied to
the MMC and then loaded from the MMC into the unit's memory.
(NOTE: No matter where they come from, GPS Data Files must be
loaded from the MMC into memory before the unit can use them.)
The other key GPS use for MMCs is storage of special high-detail, cus-
tom maps, which you can produce on your computer with our MapCre-
ate software. These MapCreate custom maps contain much greater de-
tail than the basic background map. These Custom Map Files (file
format *.lcm) can also be shared between other Lowrance GPS or so-
nar/GPS units and personal computers. (For example, the exact same
MMC, custom map files and GPS data files can be used interchangea-
bly between your gimbal-mounted GlobalMap 3300C and the hand-held
iFINDER GPS receiver.)
You make your own Custom Map Files with our MapCreate software,
but you don't have to. We also sell ready-to-use FreedomMaps. These
custom maps are pre-loaded on MMCs. (No computer work required!).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The unit automatically reads Custom Map Files directly from the MMC
or SD card. To use a custom map, all you need to do is slide an MMC
containing a map into the unit.
Introduction to GPS and WAAS
Well, now you know the basics of how the unit does its work. You might
be ready to jump ahead to Section 2, Installation & Accessories, on page
11, so you can mount your unit and plug in the power. Or you might
want to see how our text formatting makes the manual tutorials easy to
skim. If that's the case, move on to "How to Use This Manual" on page
9. But, if you want to understand the current state of satellite naviga-
tion, look over this segment describing how GPS and its new companion
WAAS work together to get you where you're going.
The Global Positioning System (GPS) was launched July 17, 1995 by
the United States Department of Defense. It was designed as a 24-
hour-a-day, 365-days-a-year, all weather global navigation system for
the armed forces of the U.S. and its allies. Civilian use was also avail-
able at first, but it was less accurate because the military scrambled
the signal somewhat, using a process called Selective Availability (SA.)
GPS proved so useful for civilian navigation that the federal govern-
ment discontinued SA on May 2, 2000, after the military developed
other methods to deny GPS service to enemy forces. Reliable accuracy
for civilian users jumped from 100 meters (330 feet) under SA to the
present level of 10 to 20 meters (about 30 to 60 feet.)
Twenty-four satellites orbit 10,900 nautical miles above the Earth,
passing overhead twice daily. A series of ground stations (with precisely
surveyed locations) controls the satellites and monitors their exact loca-
tions in the sky. Each satellite broadcasts a low-power signal that identi-
fies the satellite and its position above the earth. Three of these satellites
are spares, unused until needed. The rest virtually guarantee that at
least four satellites are in view nearly anywhere on Earth at all times.
A minimum of three satellites are required to determine a 2D fix.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The system requires signal reception from three satellites in order to
determine a position. This is called a 2D fix. It takes four satellites to
determine both position and elevation (your height above sea level —
also called altitude.) This is called a 3D fix.
Remember, the unit must have a clear view of the satellites in order to
receive their signals. Unlike radio or television signals, GPS works at
very high frequencies. These signals can be easily blocked by trees,
buildings, an automobile roof, even your body.
Like most GPS receivers, this unit doesn’t have a compass or any other
navigation aid built inside. It relies solely on the signals from the sat-
ellites to calculate a position. Speed, direction of travel, and distance
are all calculated from position information. Therefore, in order for the
unit to determine direction of travel, you must be moving and the
faster, the better. This is not to say that it won’t work at walking or
trolling speeds — it will. There will simply be more "wandering" of the
data shown on the display.
GPS alone is plenty accurate for route navigation, but the U.S. Federal
Aviation Administration has special aircraft navigation needs that go
beyond basic GPS. So, the FAA has developed a program to boost GPS
performance with its Wide Area Augmentation System, or WAAS. The
FAA commissioned the system on July 11, 2003.
WAAS is designed to increase GPS accuracy to within 7.6 meters vertically
and horizontally, but it consistently delivers accuracies within 1-2 meters
horizontal and 2-3 meters vertical, according to the FAA. It does this by
broadcasting correction signals on GPS frequencies. Your unit automati-
cally receives both GPS and WAAS signals.
However, there are some fringe areas of the U.S., including parts of
Alaska, that do not yet receive robust WAAS coverage. Continued WAAS
development is planned to extend WAAS coverage in the years to come.
WAAS boosts the accuracy of land GPS navigation, but the system is
designed for aircraft. The satellites are in a fixed orbit around the
Equator, so they appear very low in the sky to someone on the ground
in North America. Aircraft and vessels on open water can get consis-
tently good WAAS reception, but terrain, foliage or even large man-made
structures can sometimes block the WAAS signal from ground receivers.
You'll find that using your GPS receiver is both easy and amazingly
accurate. It’s easily the most accurate method of electronic navigation
available to the general public today. Remember, however, that this
receiver is only a tool. Always have another method of navigation avail-
able, such as a map or chart and a compass.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Also remember that this unit will always show navigation information
in the shortest line from your present position to a waypoint, regardless
of terrain! It only calculates position, it can’t know what’s between you
and your destination, for example. It’s up to you to safely navigate
around obstacles, no matter how you’re using this product.
Free Training Aids Available
Now that you know something about the technology that makes this
unit possible, you're ready to start learning how to use that technology!
This manual will guide you through the process of setting up and run-
ning your unit, but that's only one of many resources available.
If you or a friend has Internet access, visit our web site! Find us at
WWW.LOWRANCE.COM. The site is packed with additional information
on using our products.
Unit Emulator
For the ultimate training aid, be sure to download the free emulator
software for your unit. Aside from being just plain fun, this program
can help you learn both basic and advanced operations without burning
boat fuel! Lowrance is the first GPS manufacturer to provide this type
of training tool for customers.
This PC application simulates the actual GPS unit on your computer.
You can run it from your computer keyboard or use your mouse to press
the virtual keys. Easy download and installation instructions are avail-
able on our web site.
Free training emulator is available for your unit on our web site.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
The emulator works exactly like your real GPS unit. Using the GPS
Simulator feature, it allows you to run GPS routes and trails, even cre-
ate real waypoints you can use in the field!
And that's just some of the material available on our web site. To find
out all we have available, go to WWW.LOWRANCE.COM and look around.
For now, though, we'll get back to how to use this particular unit. And,
first, how to use the manual.
How to use this manual: typographical conventions
Many instructions are listed as numbered steps. The keypad and arrow
"keystrokes" appear as boldface type. So, if you're in a real hurry (or
just need a reminder), you can skim the instructions and pick out what
menu command to use by finding the boldface command text. The fol-
lowing paragraphs explain how to interpret the text formatting for
those commands and other instructions:
Arrow Keys
The arrow keys control the movement of dotted cross-hair lines on your
mapping screen called the cursor. The arrow keys help you move
around the menus so you can execute different commands. They are
represented by symbols like these, which denote the down arrow key,
the up arrow, the left arrow and the right arrow: ↓ ↑ ← →.
Keyboard
The other keys perform a variety of functions. When the text refers to a
key to press, the key is shown in bold, sans serif type. For example, the
"Enter/Icons" key is shown as ENT and the "Menu" key is shown as MENU.
Menu Commands
A menu command or a menu option will appear in small capital letters, in
a bold sans serif type like this: ROUTE PLANNING. These indicate that you are
to select this command or option from a menu or take an action of some
kind with the menu item. Text that you may need to enter or file names
you need to select are show in italic type, such as trail name.
Instructions = Menu Sequences
Most functions you perform with the unit are described as a sequence of
key strokes and selecting menu commands. We've written them in a
condensed manner for quick and easy reading.
For example, instructions for navigating a trail would look like this:
1. From the Map Page, press MENU|MENU|↓ to MY TRAILS|ENT.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press ↓ to Trail 1|ENT|→ to NAVIGATE|ENT.
3. You are asked to wait while it converts the trail into a route.
4. The wait message disappears and the unit begins showing
navigation information along the trail. Now, begin moving and
follow your unit's directions.
Translated into complete English, step 1 above would mean: "Start on
the Map Page. Press the Menu key twice. Next, repeatedly press (or
press and hold) the down arrow key to scroll down the menu and select
(highlight) the My Trails menu command. Finally, press the Enter key."
Step 2 would mean: "Press the down arrow key repeatedly to scroll to
the trail named Trail 1, and press Enter. Next, press the right arrow
key to highlight the Navigate command, then press Enter."
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2:
Installation & Accessories
Preparations
You can install the GPS system in some other order if you prefer, but
we recommend this installation sequence:
Caution:
You should read over this entire installation section before drill-
ing any holes in your vehicle or vessel!
1. Determine the approximate location for the GPS unit, so you can
plan how and where to route the cables for the antenna and power.
This will help you make sure you have enough cable length for the de-
sired configuration.
2. Determine the approximate location for the GPS antenna module
and its cable route.
3. Determine the location of your battery or other power connection,
along with the power cable route.
4. Install the GPS antenna and route the antenna cable to the GPS
unit's mounting location.
5. Install the power cable and route it to the GPS unit's mounting location.
6. Mount the GPS unit.
GPS Antenna/Receiver Module
This unit's package includes the LGC-2000 GPS module. This device con-
tains the unit's external antenna and receiver for GPS and WAAS signals.
The antenna/receiver module comes with a 25-foot Y-adapter extension
cable. This module can be mounted on a flat surface or pole, or an optional
magnet is available for temporary mounting on any ferrous surface.
The LGC-2000 requires 9 to 20 volts DC power. It draws power through
the unit or from the NMEA 2000 buss (instructions on powering a
NMEA 2000 buss appear later in this section).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LGC-2000 Module, bottom view (left) and top view (right).
GPS Module Installation
The GPS module can be mounted on any flat surface, provided there is
access behind the mounting surface for the screws. The optional mag-
net allows the module to be easily used on cars or off-road vehicles. The
pole mount adapter lets you mount the antenna on a pole or swivel
mount that uses standard marine 1" - 14 threads.
Surface Mount
Tools required for installation are: wire pliers, flat screwdriver, drill, 1"
(25 mm) drill bit and 3/16" (4.75 mm) drill bit.
The GPS module can be easily installed on any flat surface that is at
least 3-1/2" (90 mm) wide. Be sure that a clear, unobstructed view of
the sky is available at the selected location. GPS signals travel "line-of-
sight" at very high frequencies, so nearly anything blocking the an-
tenna can stop the unit from finding a satellite. Caution: Do not mount
in line with a radar antenna. Radar radiates high-energy signals that
can interfere with GPS signal reception.
In an automobile, you may achieve good results by simply placing the
external antenna on the top of the dash, at the base of the windshield. A
piece of the rubber non-skid shelf liner material available in recreational
vehicle supply stores will help hold the antenna in place. This may not
work well if you have a cab-over design pickup truck camper or motor
home. If dashboard reception is poor, simply relocate the antenna mod-
ule elsewhere on the vehicle for a clearer view of the sky.
Once you’ve determined the mounting location, use the template on
page 14 to drill the screw holes. The screws supplied with this unit are
about 1-1/8" long (4mm x 30mm). Drill 3/16" (4.75 mm) holes for the
mounting screws.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
If you need to route the cable through the mounting surface, drill a 1"
(25mm) hole for the cable's connector. There is a notch in the antenna
housing that allows the cable to pass through to the outside, if desired,
instead of routing it through the mounting surface.
After drilling the holes, pass the O-ring over the cable and press it into
the groove on the bottom of the antenna housing. Now attach the an-
tenna to the mounting surface, using 4 mm screws and the supplied lock
washers. Route the cable (as described later in this section) and the GPS
module installation is finished.
Magnet Mount
A magnet (available as an option) lets you temporarily mount the
GPS module on any ferrous metal surface, such as a car. To use the
magnet, simply peel the backing off the magnet's adhesive coating
and press the magnet to the bottom of the antenna housing. The
module is ready for use.
Magnet
Under side view showing magnet.
Pole Mount
The GPS module attaches to the pole mount
adapter with the supplied 4 mm screws.
You can route the cable through the slot in
the side of the module and down the side of
the pole. Or, you can pass it down through
the pole mount adapter and run the cable
inside the pole. The 1"-14 threads on the
pole mount adapter accept
marine antenna mount.
a
standard
Pole mount adapter
with module attached.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Drill size 3/16" (4.75 mm)
Drill four places.
Drill size 1" (25 mm )
(If needed.)
GPS module mounting template.
After the module is installed, connect it to the unit. The LGC-2000 can
communicate with your GPS unit either directly (using the supplied ex-
tension cable) or through a NMEA 2000 network.
Connecting Directly to the Unit
After the module is installed, attach it to the end of the Y-adapter ex-
tension cable as shown in the following diagram. To connect it to the
unit, insert the extension cable's splitter plug into the Network socket
on the back of the unit and your system is ready to use.
60-ohm
Splitter plug
terminator
LGC-2000
To unit
25' Y-adapter
extension cable
LGC-2000 direct connection to GPS unit.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
The extension cable’s shorter branch will have a 60-ohm terminator at-
tached to it. Do not remove this terminator. When you're not con-
necting to a NMEA 2000 buss, you must leave the terminator con-
nected to this socket for your antenna/receiver to function correctly.
Connecting to a NMEA 2000 Network
The LGC-2000 can be connected to a NMEA 2000 buss, providing GPS
information to any Lowrance GPS units attached to the buss. Contact LEI
Extras (look inside back cover for accessory ordering information) for a
NMEA 2000 buss adapter cable if you would like to do this.
There are two ways to connect the antenna to a NMEA 2000 network
port. One method (shown in the following image) is to use the extension
cable's Y-adapter to connect both the antenna and the unit to the same
network port. To do this, simply remove the 60-ohm terminator shown in
the previous image and attach the NMEA 2000 buss adapter cable to the
shorter branch of the extension cable's Y-adapter. Connect the NMEA
2000 buss adapter cable's other end to an available network port.
To unit
LGC-2000
25' Y-adapter
extension cable
To NMEA 2000
network port
LGC-2000 and GPS unit connection to NMEA 2000 buss.
You can also attach the antenna to a remote port on the network, and
pass position information along the network. To do this, simply attach the
LGC-2000's connector to one end of the buss adapter cable and attach the
other to an available port on the NMEA 2000 buss, as shown in the fol-
lowing image. (You will have to use a similar adapter cable to connect the
GPS unit to the NMEA buss as described later in this section.)
To NMEA 2000
network port
LGC-2000
LGC-2000 remote connection to NMEA 2000 buss.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
An existing operational NMEA 2000 buss will already have termina-
tors in place and will already be powered. If you're connecting to such a
network, you won't need the terminators provided. Do not add termi-
nators or power to a functional NMEA 2000 buss!
When the LGC-2000 is connected to the unit (directly or indirectly), it
will begin providing GPS signal information.
Power Connections
Your unit comes with a Lowrance standard power/data cable that splits
into three ends, each with several exposed wires (shown in the follow-
ing figure). The end with 4 wires (blue, yellow, orange and shield) is a
Data cable that connects to a NMEA 0183 interface. The end with three
wires (red, black and shield) is a power cable that connects to a NMEA
2000 buss. The thicker three-wire cable (red, black and white) is the
Power Supply for your unit (and optional external speaker connection
for some units).
Power Supply wires:
red, black and white
To unit
NMEA 2000 Power wires:
red, black and shield
NMEA 0183 Data Cable
wires: blue, yellow,
orange and shield
The Power/Data cable for this unit.
Depending on your configuration, you may not use all of these wires.
(For example, many units cannot operate an optional external speaker,
so the white wire on the Power Supply cable isn't functional.) The fol-
lowing segments include instructions for installing all the wires that
you will use with this unit.
Caution:
All of the wires in the power/data cable have bare ends for eas-
ier installation. The bare ends on any unused wires could cause
an electrical short if left exposed. To prevent this, you should
cover the individual wire ends – either by capping them with
wire nuts or wrapping them with electrical tape. (You should cut
off the bare wire before taping off the ends.)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering a NMEA 2000 Buss
(NMEA 2000 Power cable)
A NMEA 2000 buss must be connected to a power source to operate. If
you have a pre-existing NMEA 2000 installation, it may already be
connected to another power source. If your NMEA 2000 buss is already
powered, you can ignore the NMEA 2000 Power cable. Never attach
two power sources to a single NMEA 2000 buss.
If you do need to power your NMEA 2000 buss, attach the NMEA 2000
Power cable to your boat's battery just as indicated in the following
segment for connecting your unit's Power Supply cable. The NMEA
2000 Power cable's red wire should be attached (with provided 3-amp
fuse) to the boat battery's positive terminal, and the NMEA 2000 Power
cable's black and shield wires should both be attached to the battery's
negative terminal.
NOTE:
If the NMEA 2000 buss draws power directly from the boat's battery,
the LGC-2000 will remain on (drawing power) all the time. The LGC-
2000's current draw is very small and shouldn't decrease the boat's
storage battery life, but if this small draw is a concern, you can in-
stall a switch between the NMEA 2000 buss and the battery.
Powering Your Unit
(Power Supply cable – red and black wires)
The unit works from a 12-volt battery system. For the best results, at-
tach the power cable directly to the battery. You can attach the power
cable to an accessory or power buss, however you may have problems
with electrical interference. Therefore, it's safer to go ahead and attach
the power cable directly to the battery.
CAUTION:
When using the unit in a saltwater environment, we strongly rec-
ommend that you shut off the power supply to the power cable when
the unit is not in use. When the unit is turned off but still connected
to a power supply, electrolysis can occur in the power cable plug.
This may result in corrosion of the plug body along with the electri-
cal contacts in the cable and the unit's power socket.
In saltwater environments we recommend you connect the power
cable to the auxiliary power switch included in most boat designs.
If that results in electrical interference, or if such a switch is not
available, we recommend connecting direct to the battery and in-
stalling an inline switch. This will let you shut off power to the
17
Download from Www.Somanuals.com. All Manuals Search And Download.
power cable when the unit is not in use. When you are not using
the unit, you should always shut off power to the power cable, es-
pecially when the power cable is disconnected from the unit.
If possible, keep the power cable away from other boat wiring, especially
the engine's wires. This will provide the best isolation from electrical
noise. If the cable is not long enough, splice #18 gauge wire onto it. The
power cable has two wires, red and black. Red is the positive lead, black
is negative or ground. There is also a white wire to power an optional
external speaker for some units. Make sure to attach the in-line fuse
holder to the red lead as close to the power source as possible.
For example, if you have to extend the power cable to the battery or
power buss, attach one end of the fuse holder directly to the battery or
power buss. This will protect both the unit and the power cable in the
event of a short. It uses a 3-amp fuse.
White external speaker wire
(not used by this unit)
To unit
Red wire with
3 amp fuse
Black wire
To power a
NMEA 2000
buss, also
connect
NMEA 2000
Power cable
to the boat's
battery.
Optional power off
switch for salt-
water installations
12 volt
battery
Data Cable
NMEA 2000 Power Cable
Power connections for the unit.
NOTE:
If you're powering a NMEA 2000 buss, you will attach both the
NMEA 2000 Power cable and the unit's Power Supply cable to the
boat's battery. To attach the NMEA 2000 Power cable, connect the
red wire to battery's + and black and shield wires to battery's –.
WARNING:
This product must be independently fused with the en-
closed 3-amp fuse (or equivalent), even if you connect to
a fused accessory or power buss.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
If a malfunction happens inside the unit, extensive dam-
age can occur if the enclosed fuse is not used. As with all
electrical devices, this unit could be damaged to a point
that it is unrepairable and could even cause harm to the
user when not properly fused.
CAUTION:
Do not use this product without a 3-amp fuse wired into the power
cable! Failure to use a 3-amp fuse will void your warranty.
This unit has reverse polarity protection. No damage will occur if the
power wires are reversed. However, the unit will not work until the
wires are attached correctly.
An optional 8-foot, CA-4 external power cable with a cigarette lighter
adapter is available from Lowrance.
NMEA 2000 Cable Connections
NMEA 2000 is a new buss network specifically designed for boats. This is
a very young industry standard and, at the time of printing, few boats
being built now have a NMEA 2000 buss installed. Over the next few
years, however, NMEA 2000 will become much more common. To help
you get the most out of this technology, your Lowrance unit is designed
to work with a NMEA 2000 network as soon as it becomes available.
Connecting to a NMEA 2000 Network
Your unit can be connected to a NMEA 2000 buss, receiving sensor infor-
mation from any Lowrance units attached to the buss. Contact LEI Extras
(look inside back cover for accessory ordering information) for a NMEA
2000 buss adapter cable if you would like to do this. You can connect both
the unit and antenna module through the antenna's extension cable (as
described earlier), or you can connect the unit directly to a network port.
To do so, simply attach the adapter cable's manual locking collar connector
to the Network port on the back of the unit and attach the other end to an
available port on the NMEA 2000 buss, as shown in the following image.
To NMEA 2000
To GlobalMap's
network port
Network socket
Lowrance unit direct connection to NMEA 2000 buss.
As soon as the unit is connected to the network, it will begin receiving
shared information. Please note that the buss must be powered to oper-
ate. (For more on powering a NMEA 2000 buss, see the instructions
earlier in this section.)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
NMEA 0183 Cable Connections
NMEA is a standard communications format for marine electronic
equipment. For example, an autopilot can connect to the NMEA inter-
face on this unit and receive positioning information. The unit can ex-
change information with any device that transmits or receives NMEA
0183 data.
See the following diagram for general wiring connections. Read your
other product’s owner’s manual for more wiring information.
NMEA 0183 Wiring
(Data cable)
To exchange NMEA 0183 data, this unit has one NMEA 0183 version
2.0 communication port. Com port one (Com-1) can be used to receive
NMEA format GPS data. The com port can also transmit NMEA format
GPS data to another device.
The four wires for the com port are combined with the Power Supply
cable and NMEA 2000 Power cable to form the power/data cable (shown
earlier). Com-1 uses the yellow wire to transmit, the orange wire to re-
ceive and the shield wire for signal ground. Your unit does not use the
blue wire.
Orange (Receive)
Shield (Ground)
NMEA Transmit
Ground
To Other
GPS Receiver
Com-1
To unit
Com-1 wiring to receive NMEA position information
from some other GPS receiver.
Yellow (Transmit)
Shield (Ground)
NMEA Receive
Ground
Com-1
To unit
To Other
Device
Com-1 wiring to transmit NMEA position information
to another NMEA-compatible device.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS unit,
rear view
Network socket
Power/Data socket
NMEA 0183
Data cable
(four wires)
LGC-2000 25'
extension cable
NMEA 2000
Power cable
60-ohm
terminator
Power Supply
cable
GPS
antenna
module
Cable connections shown.
Mounting the Unit: Bracket or In-Dash Installation
You can install the unit on the top of a dash with the supplied gimbal
bracket. It can also be installed in the dash or mounted on a portable
power supply.
If you use the supplied bracket, you may be interested in the optional
R-A-M bracket mounting system. This converts the unit's gimbal
bracket to a swivel mount, which can be used on the dash or overhead
mounting positions.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional R-A-M mounting system.
Bracket Installation
Mount the unit in any convenient location, provided there is clearance
behind the unit when it's tilted for the best viewing angle. You should also
make sure there is enough room behind the unit to attach the power,
transducer and GPS antenna/receiver module cables. (A drawing on the
next page shows the dimensions of a gimbal-mounted unit.)
Holes in the bracket's base allow wood screw or through-bolt mounting.
You may need to place a piece of plywood on the back side of thin fiber-
glass panels to reinforce the panel and secure the mounting hardware.
Front
Install the gimbal bracket. Orient the bracket so the arms slope toward
the front of your unit.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Drill a 1-inch (25.4 mm) hole in the dash for the power, transducer and
antenna cables. The best location for this hole is immediately under the
gimbal bracket location. This way, the bracket can be installed so that
it covers the hole, holds the cables in position and results in a neat in-
stallation. Some customers, however, prefer to mount the bracket to the
side of the cable hole — it's a matter of personal preference.
77.1
[3.03]
27.6
[1.09]
173.9
[6.85]
137.9
[5.43]
157.9
[6.22]
56.9
[2.24]
Millimeter
[Inch]
Front view (left) and side view (right) showing dimensions of Global-
Map 3300C GPS unit when mounted on gimbal bracket.
After drilling the hole, pass the transducer connector up through the
hole from under the dash, followed by antenna connector. Pass the
power cable's bare-wire end down though the hole from the top.
If you wish, you can fill in the hole around the cables with a good ma-
rine caulking compound. (Some marine dealers stock cable hole covers
to conceal the opening.) No matter what type of installation you prefer,
be sure to leave enough slack in the cables to allow tilting or swiveling
the unit. If you choose to fill in the hole, be sure to position the cables
against the rear edge of the hole as you apply the fill material.
Before positioning the bracket, be sure to hold the cables against the
rear edge of the hole. Then, slide the bracket over the hole and butt the
rear of the bracket base firmly against the cables, thus pinning them in
23
Download from Www.Somanuals.com. All Manuals Search And Download.
place against the side of the hole. Finally, fasten the bracket to the
dash. Attach the unit to the gimbal bracket using the supplied gimbal
knobs and washers.
In-Dash Installation
You can mount the unit in the dash with an optional FM-5 In-Dash
Adapter Kit. The kit includes mounting hardware, a template for cut-
ting the hole and an instruction sheet, part 988-0147-43.
146.5
[5.76]
Top
R 7.9
[0.31]
In-Dash
Template
113.5
[4.46]
Millimeters
[Inches]
ALWAYS VERIFY DIMENSIONS
In-dash mounting template for GlobalMap 3300C GPS unit, showing
dimensions. NOTE: The figure above is not printed to scale. A scaled
template (FM-5 In-Dash Adapter Kit instructions) is available for free
download from our web site, www.lowrance.com.
MMC or SD Card Memory Card Installation
Your unit uses a MultiMedia Card to store information, such as custom
maps, waypoints, trails and other GPS data. The unit can also use Se-
cure Digital Cards (SD card) to store data.
NOTE:
Throughout this manual, we will use the term MMC, but just re-
member that your unit can use an MMC or SD card to store data.
Both of these solid-state flash memory devices are about the size of a
postage stamp. An SD card is slightly thicker than an MMC. As this
manual went to press, MMCs were available in storage capacities of 8
MB, 16 MB, 32 MB, 64 MB and 128 MB. SD cards were available in
capacities of 8 MB, 16 MB, 32 MB, 64 MB, 128 MB, 256 MB and higher.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional MMC cards are available from LEI Extras; see ordering in-
formation inside the back cover of this manual. MMCs and SD cards
are also available at many camera and consumer electronics stores.
The MMC slot is located in a compartment on the front of the case. The
compartment door is located at the lower right corner. The following
figure shows a close-up with the door opened.
Thumb
screw
Insert card face up,
this way
Memory card compartment with a 16 MB MMC card installed.
To remove an MMC
1. Open the card compartment door by unscrewing the thumb screw.
The screw should only be finger tight. If it was over-tightened, use a
thumbnail, a coin or a screwdriver to open the door.
2. Just press a finger against the label of the MMC and drag it from the slot.
3. Close the compartment door and fasten the thumb screw finger tight.
To add an MMC or SD Card
1. Open the card compartment door.
2. Grasp the bottom of the MMC and push the top of the card into the
slot. Once the card is started, use your fingernails to slide it the rest of
the way to the left, until it is firmly seated in the slot.
3. Close the compartment door and fasten the thumb screw finger tight.
Face Cover
Your unit comes with a white protective cover that snaps on and off the
front of the unit. This cover is intended for use when your unit and the
vehicle it's mounted in are idle.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Accessories
Other accessories include MMC cards, MMC card readers and MapCre-
ate™ 6 custom mapping software for your computer. MMC card readers
are available in USB and parallel port versions.
MapCreate™ 6 CD-ROM, left; MMC card reader for USB ports, right.
WARNING:
When the unit is mounted in an unprotected area, such
as an open boat cockpit, the protective face cover must
be removed when the vehicle is moving at high speed.
This includes towing a boat on a trailer at highway
speeds. Otherwise, wind blast can pop off the cover.
If any of these accessories are not available from your dealer, see the
accessory ordering information on the inside back cover of this man-
ual. Visit our web site for a complete listing of all the available ac-
cessories for your unit.
Now that you have your unit installed, move on to Sec. 3, Basic GPS
Operations. There, we'll present a series of step-by-step tutorials to
teach you the basics of GPS operation.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3:
Basic GPS Operations
This section addresses the unit's most basic GPS operations. The tuto-
rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced
GPS Operations, will discuss other more advanced functions and utili-
ties. Material in Sec. 4 is arranged in alphabetical order.
Before you turn on the unit and find where you are, it's a good idea to
learn about the different keys, the three Page screens and how they all
work together. BUT, if you just can't wait to get outside, turn to the
one-page Quick Reference on page 40.
Keyboard
4
8
9
2
3
5
7
6
1
MMC slot access door
GlobalMap 3300C GPS unit, front view, showing full map, keyboard
and access door for the MMC slot.
1. PWR/LIGHT (Power & Light) – The PWR key turns the unit on and
off and activates the backlight.
2. PAGES – Pressing this and the ← → arrow keys (4) switches the
unit between the three different page screens. (Satellite Status Page,
Navigation Page and Map Page.) Each page represents one of the unit's
major operation modes.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
3. MENU – Press this key to show the menus and submenus, which
allow you to select a command or adjust a feature. This also accesses
search functions for streets, intersections, addresses and highway exits.
4. ARROW KEYS – These keys are used to navigate through the
menus, make menu selections and move the map cursor.
5. ENT/ICONS (Enter & Icons) – This key allows you to save data, ac-
cept values or execute menu commands. It is also used to create event
marker icons.
6. EXIT – The Exit key lets you return to the previous screen, clear
data or erase a menu.
7. WPT – (Waypoint) The Waypoint key is used to save and recall way-
points, search for waypoints and access the waypoint list. It also
launches the Point-of-Interest (POI) search menus and is involved in
some navigation functions.
8. ZOUT – (Zoom Out) – This key lets you zoom the screen out. This
lets you see a larger geographic area on the map. Less detail is seen as
you zoom out.
9. ZIN – (Zoom In) – This key lets you zoom the screen in. Zooming in
lets you see greater detail in a smaller geographic area on the map.
Power/lights on and off
To turn on the unit, press PWR. As the unit powers up, the Map Page is
displayed first. (To switch to another page, press PAGES|← or → to
Page Name|EXIT.)
To turn on the backlight, press PWR again. The unit has three backlight
levels to select from. Repeatedly pressing PWR will cycle through the
backlight settings and turn off the backlight.
Turn off the unit by pressing and holding the PWR key for 3 seconds.
Main Menu
The unit has a Main Menu, which contains some function commands and
some setup option commands. The tutorial lessons in this section will
deal only with functions, the basic commands that make the unit do
something. The GPS will work fine for these lessons right out of the box
with the factory default settings. But, if you want to learn about the
various options, see Sec. 5, System Setup and GPS Setup Options.
You can access the Main Menu from any of the three Page screens by
pressing MENU|MENU. To clear the menu screen and return to the page
display, press EXIT.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu.
The Main Menu commands and their functions are:
Screen command: changes the contrast or brightness of the display
screen.
Sounds command: enables or disables the sounds for key strokes and
alarms and sets the alarm style.
Transparency command: adjust the level of transparency for menus.
Alarms command: turns GPS alarms on or off and changes alarm
thresholds.
Route Planning command: used to plan, view or navigate a route.
My Trails command: shows, hides, creates and deletes plot trails. Also
used to navigate or backtrack a trail.
Cancel Navigation command: turns off the various navigation com-
mands. Used to stop navigating after you have reached your destina-
tion waypoint, Point of Interest or map cursor location; or after you
reach the end of a route or trail.
GPS Setup command: sets various GPS receiver options.
System Setup command: sets general configuration options.
Sun/Moon Calculations command: finds the rising and setting time
of the sun and the moon.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Trip Calculator command: shows trip status and statistics.
Timers command: controls the up timer, down timer and alarm clock
settings.
Browse MMC Files command: this allows you to view the installed
MMC card and the files it contains.
Pages
The unit has three Page displays that represent the three major oper-
ating modes. They are the Satellite Status Page, the Navigation Page
and Map Page. They are accessed by pressing the PAGES key, then us-
ing → or ← to select a Page. (Clear the Pages Menu by pressing EXIT.)
Pages Menu, showing some Map display options.
Satellite Status Page
The Satellite Status Page, shown in the following images, provides de-
tailed information on the status of the unit's satellite lock-on and posi-
tion acquisition. To get to the Satellite Status Page: Press the PAGES
key, then use → or ← to select STATUS. (Clear the Pages Menu by
pressing EXIT.)
No matter what Page you are on, a flashing current position indica-
tor/question mark symbol and flashing GPS data displays indicate that
satellite lock has been lost and there is no position confirmed. The Sat-
ellite Status Page shows you the quality and accuracy of the current
satellite lock-on and position calculation.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING:
Do not begin navigating with this unit until the numbers
have stopped flashing!
Satellite Status Page. Left view indicates unit has not locked on to any
satellites and does not have a fix on its position. Center view shows sat-
ellites being scanned. Right view shows satellite lock-on with a 3D posi-
tion acquired (latitude, longitude and altitude), and WAAS reception.
This screen shows a graphical view of the satellites that are in view. Each
satellite is shown on the circular chart relative to your position. The point in
the center of the chart is directly overhead. The small inner ring represents
45° above the horizon and the large ring represents the horizon. North is at
the top of the screen. You can use this to see which satellites are obstructed
by obstacles in your immediate area if the unit is facing north.
The GPS receiver is tracking satellites that are in bold type. The re-
ceiver hasn't locked onto a satellite if the number is grayed out, there-
fore it isn't being used to solve the position.
Beneath the circular graph are the bar graphs, one for each satellite in
view. Since the unit has twelve channels, it can dedicate one channel
per visible satellite. The taller the bar on the graph, the better the unit
is receiving the signals from the satellite.
NOTE:
One of the data display options for the Satellite Status page is "Po-
sition Error" (horizontal position error), which can appear in one of
the page's data boxes. Position Error will show you the expected er-
ror from a benchmark location. In other words, if the Position Error
box shows 50 feet, then the position shown by the unit is estimated
to be within 50 feet of the actual location.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
This also gives you an indicator of the fix quality the unit currently
has. The smaller the position error number, the better (and more ac-
curate) the fix is. If the position error flashes dashes, then the unit
hasn't locked onto the satellites, and the number shown isn't valid.
(For details, see the Customize Page Displays entry in Sec. 5.)
The Satellite Status Page has its own menu, which is used for setting
various options. (Options and setup are discussed in Sec. 5). To access
the Satellite Status Page Menu, from the Status Page, press MENU.
Navigation Page
This screen has a compass rose that not only shows your direction of
travel, but also the direction to a recalled waypoint. To get to the Navi-
gation Page: Press PAGES|→ or ← to NAVIGATION|EXIT.
The navigation screen looks like the one below when you're not navi-
gating to a waypoint or following a route or trail. Your position is
shown by an arrow in the center of the screen. Your trail history, or
path you've just taken, is depicted by the line extending from the arrow.
The arrow pointing down at the top of the compass rose indicates the cur-
rent track (direction of travel) you are taking.
Track or compass heading indicator, showing direction of travel
Compass
rose
Trail line
Navigation
information
Present
displays in
position
customizable
arrow
data boxes
Navigation Page, recording a trail, traveling southwest. Page looks
like this when the unit is not navigating to a waypoint, following a
route, or backtracking a trail.
When navigating to a waypoint, the Navigation screen looks like the
following figure. Your ground speed, track, distance and bearing to
waypoint, and course are all shown digitally on this screen.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
Remember, when the Speed, Track and Position information dis-
plays are flashing, satellite lock has not been achieved and no posi-
tion fix has been determined. A question mark will also flash on the
present position arrow in the center of the compass rose.
Speed (ground speed) is the velocity you are making over the ground. (If
you wish, you can customize the Speed data box to display Closing
Speed instead. Closing Speed is also known as velocity made good. It's
the speed that you're making toward the waypoint. For instructions,
see the Customize Page Displays entry in Sec. 5.)
Track is the heading, or the current direction you are actually travel-
ing. Bearing is the direction of a line-of-sight from your present position
to the destination. No matter what direction you are steering, the
Bearing window shows the compass direction straight to the destina-
tion from your location at the moment. Distance shows how far it is to
the waypoint you're navigating toward.
The Off Course window shows the current cross track error. This shows
the distance you are off-course to the side of the desired course line. The
course line is an imaginary line drawn from your position when you
started navigating to the destination waypoint. The course line is shown on
the Navigation Page screen (and the Map Page screen) as a dotted line.
Course line
Heading arrow
Left cross track error line
Waypoint
symbol
Bearing
arrow
Cross track
error range
Trail line
(off course
indicator)
Navigation
information
displays
in data
Destination
name
boxes
Compass bearing
to destination
Current track or heading,
shown in degrees
Navigation Page, going to a waypoint while creating a new trail.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
The cross track error range is shown on the compass rose as a wide,
white, corridor enclosing the course line. The outer edges of this white
corridor represent lines that show the current cross track error range.
The default for the cross track error range is 0.20 miles.
For example, if the present position symbol touches the right cross
track error line, then you are 0.20 miles to the right of the desired
course. You need to steer left to return to the desired course. You can
use the ZIN or ZOUT keys to change the cross track error range.
A circular symbol depicting your destination (waypoint) appears on the
screen as you approach the waypoint, as shown on the screen in the
preceding figure.
Travel Time is the time that it will take to reach your destination at
your present closing speed. (You can also customize the time data box
to show Arrival Time instead. Arrival Time is the local time it will be
when you arrive at the destination, based upon your present closing
speed and track.)
In the preceding example figure, the driver is headed northwest (a 345º
track) toward a waypoint 346º (bearing) away. The cross track error
range (white corridor) is 0.15 miles either side of the course. The driver
is headed toward trail waypoint 1, which is 0.3 miles away. The vehicle
is 234 feet right of the original course. Traveling at a speed of 17 mph,
the driver will arrive at the waypoint in 1 minute, 3 seconds.
The Navigation Page has its own menu, which is used for some ad-
vanced functions and for setting various options. (Options and setup
are discussed in Sec. 5). To access the Navigation Page Menu, from the
Navigation Page, press MENU.
Map Page
The Map Page screens show your course and track from a "bird's-eye"
view. By default, this unit shows the map with north always at the top
of the screen. (This can be changed. See the topic Map Orientation, in
Sec. 5.) If you're navigating to a waypoint, the map also shows your
starting location, present position, course line and destination. You
don't have to navigate to a waypoint, however, to use the map.
Map Page is the default screen that appears when you turn on the unit.
To get to the Map Page from another page: Press PAGES|→ or ← to
MAP|EXIT. When the Map Page is displayed, a screen similar to the fol-
lowing figures appears.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
The arrow in the center of the screen is your present position. It points
in the direction you're traveling. The solid line extending from the back
of the arrow is your plot trail, or path you've taken.
The map zoom range is the distance across the screen. This number
shows in the lower left corner of the screen. In the first of the following
example figures, the range is 4,000 miles from the left edge of the map
to the right edge of the map.
The Zoom In and Zoom Out keys zoom the map to enlarge or reduce its
coverage area and the amount of mapping detail shown. There are 40
available map zoom ranges, from 0.02 miles to 4,000 miles.
Far left, Map Page opening screen. Center, zoomed to 100 miles and
right, zoomed to 10 miles. Over Zoomed means you have reached the
detail limits in an area covered only by the basic background map.
Zooming in any closer will reveal no more map details because a high-
detail custom map has not been loaded on the MMC for this area.
If you're using only the factory-loaded background map, the maximum
zoom range for showing additional map detail is 15 miles. You can con-
tinue to zoom in closer, but the map will simply be enlarged without
revealing more map content (except for a few major city streets.) Load
your own high-detail custom map made with MapCreate (or a pre-made
FreedomMap from LEI), and you can zoom in to 0.02 miles with mas-
sive amounts of accurate map detail.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Map Pages with high-detail MapCreate map of an urban area loaded on
the MMC. At left, arterial streets are visible at the 4 mile zoom range.
Center, numerous dots representing Points of Interest are visible at the
2 mile range, along with minor streets. Right, at the 0.4 mile zoom, you
can see an interstate highway with an exit, major and minor streets as
well as Point of Interest icons.
Background map vs. MapCreate map content
The background map includes: low-detail maps of the whole world (con-
taining cities, major lakes, major rivers, political boundaries); and me-
dium-detail maps of the United States.
The medium-detail U.S. maps contain: all incorporated cities; shaded
metropolitan areas; county boundaries; shaded public lands (such as
national forests and parks); some major city streets; Interstate, U.S.
and state highways; Interstate highway exits and exit services informa-
tion; large- and medium-sized lakes and streams; and more than 60,000
navigation aids and 10,000 wrecks and obstructions in U.S. coastal and
Great Lakes waters
MapCreate custom maps include massive amounts of information not
found in the background map. MapCreate maps contain the searchable
Points of Interest database, all the minor roads and streets, all the
landmark features (such as summits, schools, radio towers, etc.); more
rivers, streams, smaller lakes and ponds and their names.
What's more important is the large scale map detail that allows your
GPS unit to show a higher level of position accuracy. For example, the
background map would show you the general outline and approximate
shape of a coastline or water body, but the higher detail in MapCreate
shows the shoreline completely and accurately (finer detail). Many
smaller islands would not be included in the background map, but are,
of course, in MapCreate.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
Available through LEI Extras (look inside back cover for accessory
ordering information), FreedomMaps are pre-made maps that con-
tain all of the same information available in a custom MapCreate
map, without any of the work of preparation.
Major Street
Interstate
Cursor line
Minor
Streets
POI
Pop-up
POI
Marker
School POI
Restaurant
POI
Position, distance
and bearing data
Zoom Range
When the map is zoomed out far enough, most POIs appear as square
dots. As you zoom in closer, the symbols become readable icons. In the
0.2 mile zoom example at right, the cursor has selected the Cupps Café
POI, which triggers a pop-up box with the POI name. This pop-up box
works on POIs at any zoom range.
Tip:
In some urban areas, businesses are so close to one another that
their POI icons crowd each other on the screen. You can reduce
screen clutter and make streets and other map features easier to
see by simply turning off the display of POIs you're not watching
for. (To see how, check the text on Map Detail Category Selection,
page 84. It shows how to use the Map Categories Drawn menu to
turn individual POI displays off and on.) Even though their display
is turned off, you can still search for POIs and their icons will pop-
up when your unit finds them for you.
The Map Page has its own menu, which is used for several functions
and for setting various options. To access the Map Page Menu, from the
Map Page, press MENU.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
The Pages Menu also offers several map display options under the Map
Page category. To access them, press PAGES|← or → to MAP|↓ to Op-
tion|EXIT.
Digital Data map page option.
In pages that have two major windows (such as two maps) you can tog-
gle back and forth between the two windows by pressing
PAGES|PAGES. This allows you to change which map your cursor
moves on, and which map the menu operates on.
Pages Menu with Two Map option selected, left.
Map Page with two map windows, at right.
Resize Window command
Resize Window is another extremely handy feature for pages that have two
major windows. You can change the relative size of the windows, as well as
horizontal or vertical layout, to suit your viewing preference. Here's how:
38
Download from Www.Somanuals.com. All Manuals Search And Download.
1. From any two-window display, press MENU|↓ to RESIZE WINDOW|ENT.
2. Four flashing arrows appear along the centerline dividing the two
windows. Press an arrow key perpendicular to the centerline to adjust
the window widths. Press an arrow key parallel to the centerline to
switch between horizontal and vertical layout.
Press EXIT to clear the four flashing arrows.
Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
From left to right: Fig. 1. Resize Window command on the GPS Page
menu. Fig. 2. Two Maps page display with four flashing arrows on the
dividing centerline. Fig. 3. The centerline has been moved down to en-
large the top map, which is now zoomed in to 40 miles. Fig. 4. Pressing
→ has switched the page layout from horizontal to vertical – note that
the relative sizes remain the same.
3. To change the window size again or revert back to the original dis-
play, just follow the steps above. (Most dual-window displays use half
the screen for each window by default.) You can also use the Reset Op-
tions command to revert to the factory default.
NOTE:
The units described by this manual are all capable of using this
command. If your unit does not have a Resize Window command on
the Map Page menu, you can update your software by visiting our
website WWW.LOWRANCE.COM or by contacting customer service.
The following page contains a 12-step quick reference for the most basic
GPS operations. If you don't want to carry the manual with you as you
practice with the unit, you might consider photocopying this quick ref-
erence page and tucking it into your pocket.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic GPS Quick Reference
Start outdoors, with a clear view of the open sky. As you practice, try
navigating to a location at least a few blocks away. While you're learning,
navigation in too small an area will constantly trigger arrival alarms.
1. Connect the unit to electric power and the antenna module. Make sure
the MMC is in. (See complete installation details beginning on page 11.)
2. To turn on the unit, press and release PWR key.
3. Opening screen displays map of North America at the 4,000 mile
zoom range. Rotate through the three main Page screens (Map Page,
Satellite Status Page and Navigation Page) by pressing PAGES|← or →
to select Page Name|EXIT. Switch Pages to display Satellite Status
Page.
4. Wait while unit locates satellites and calculates current position. Process
is visible on Satellite Page. This takes an average of 1 minute or less under
clear sky conditions (unobstructed by terrain or structures.) When the unit
acquires position, a tone sounds and a position acquired message appears.
5. With position acquired, press PAGES key to display Map Page, which
shows a bird's eye view of the earth. You can move around the map by:
Zoom in closer to see greater detail: press ZIN (zoom in key.)
Zoom out to see more area, less detail: press ZOUT (zoom out key.)
Scroll map north, south, east or west using arrow keys ↑ ↓ → ← .
To stop scrolling and return to current position on map, press EXIT key.
6. Set a waypoint (Wpt 001) at your current position so you can navigate
back here: press WPT|WPT. Waypoint symbol and "001" appears.
7. Zoom/scroll map to find a nearby object or location to go to. Use ar-
row keys to center cursor cross-hair over the map object or location.
8. Navigate to the selected destination: press MENU|ENT|EXIT. Follow red
course line on Map Page or compass bearing arrow on Navigation Page.
9. At destination, Arrival Alarm goes off; to clear it, press EXIT. Cancel
navigation: press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
10. Return to Wpt 1 by Navigate To Waypoint or Backtrack Trail. To
Waypoint: press WPT|ENT|ENT|ENT. Use ↑ or ↓ to select Wpt 001,
press ENT|ENT; follow navigation displays. Trail: press MENU|MENU|↓
to MY TRAILS|ENT. Press ↓ to Trail 1|ENT|↓ to DELETE TRAIL|→ to
NAVIGATE|ENT. Press → to REVERSE ROUTE|ENT|← to NAVIGATE ROUTE|ENT.
(If arrival alarm sounds, press EXIT.) Follow navigation displays.
11. Back home, Arrival Alarm goes off; press EXIT. Cancel navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
12. To turn off the unit, press and hold PWR key for three seconds.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Your Current Position
Finding your current position is as simple as turning the unit on. Un-
der clear sky conditions, the unit automatically searches for satellites
and calculates its position in approximately one minute or less.
NOTE:
"Clear sky" means open sky, unobstructed by terrain, dense foliage
or structures. Clouds do not restrict GPS signal reception.
If for some reason satellite acquisition takes longer, you may be inside
a structure or vehicle or in terrain that is blocking signal reception. To
correct this, be sure you are positioned so that the unit's antenna mod-
ule has as clear a view of the sky as possible, then turn the unit off and
back on again.
Moving Around the Map: Zoom & Cursor Arrow Keys
The map is presented from a bird's eye view perspective. The current
zoom range shows in the lower left corner of the screen.
1. Press the ZIN key (zoom in) to move in closer and see greater detail in
a smaller geographic area.
2. Press the ZOUT key (zoom out) to move farther away and see less map
detail, but a larger geographic area.
When you are traveling, the map will automatically move as you move.
This keeps your current location roughly centered on the screen.
You can manually pan or scroll the map northward, southward, east-
ward or westward by using the arrow keys, which launch the cross-hair
map cursor. This allows you to look at map places other than your cur-
rent position. To clear the cursor, press EXIT, which jumps the map
back to the current position or the last known position.
Tip:
Use the cursor to determine the distance from your current position
(or last known position, when working indoors) to any map object or
location. Simply use the arrow keys to position the cursor over the
object or place. The distance, measured in a straight line, appears
in the popup data box. Press EXIT to clear the cursor.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Distance
measured
by cursor
Pop-up
name box
Selected wreck
Cursor
line
Cursor line
The selected wreck (the Empress) to the southeast is 12.81 miles away.
Selecting Any Map Item With the Cursor
1. Use the zoom keys and the arrow keys to move around the map and
find the item you wish to select.
2. Use the arrow keys and center the cursor cross-hair on the desired ob-
ject. On most items, a pop-up box will give the name of the selected item.
Tip:
This unit has an extremely handy Cursor Undo feature that lets
you instantly return to the previous location you were looking at
without scrolling. It works like this: Use the cursor (arrow keys) to
scroll the map to some far away location or waypoint. Press EXIT to
clear the cursor and jump back to your current position on the map.
When you want to take another peek at that distant place, just
press EXIT again. You can use this trick to toggle between your cur-
rent position and your destination without a lot of scrolling.
Searching
Now that you've seen how the unit can find where you are, let's search
for something somewhere else. Searching is one of the most powerful
features in the Lowrance GPS product line.
In this example, we'll look for the nearest fast-food restaurant. For more
information on different types of searches, refer to Sec. 6, Searching.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
This example requires the Point of Interest (POI) database included
with a high detail MapCreate 6 custom map.
After the unit has acquired a position:
1. Press WPT|↓ to POI-RESTAURANTS.
2. You could search the entire restaurant category, but in this example
we will narrow our search. Press → to FAST FOOD CHAINS|ENT|↓ to
NEAREST|ENT.
3. The unit says it is calculating, then a list of restaurants appears,
with the closest at the top of the list, and the farthest at the bottom of
the list. The nearest is highlighted.
Find Waypoint Menu, left; Category Selection menu, center; and list of
the nearest restaurants, right.
4. If you wish, you could scroll ↑ or ↓ here to select another restaurant,
but for now we will just accept the nearest one. Press ENT.
5. The POI information screen appears. (This is how you can use this
unit as a business phone directory!) If you wanted to navigate there,
you could press Enter, since the Go To waypoint command is high-
lighted. But we just want to see it on the map, so press → to FIND ON
MAP|ENT.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
POI information screen on fast food restaurant nearest this position.
Screen shows name, street address, phone number, latitude/longitude,
distance to restaurant and its compass bearing. Figure at left shows
Go To waypoint command; right figure shows Find On Map command.
6. The unit's map appears, with the cross-hair cursor highlighting the
restaurant' s POI symbol. A pop-up data box shows the POI's name. A
data box at the bottom of the screen displays the location's latitude and
longitude, distance and bearing.
Map screen showing Finding Waypoint,
the result of a restaurant search.
7. To clear the search and return to the last page displayed, press
EXIT|EXIT|EXIT|EXIT. (Before you completely exited out of the Search
menus, you could have gone looking for another place.)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
Search works from mapping and POI data loaded in the unit. If
you do not have a high-detailed custom map (containing POI data)
for the area you are searching loaded on the MMC, you may not
find anything.
Set a Waypoint
A waypoint is simply an electronic "address," based on the latitude and
longitude of a position on the earth. A waypoint represents a location,
spot, or destination that can be stored in memory, then be recalled and
used later on for navigation purposes.
You can create a waypoint at the cursor position on the map, or at your
current position while you are navigating. You can create a waypoint at
any location by manually entering the position's latitude and longitude.
You can copy waypoints from your unit to your personal computer with
MapCreate software. When you want to repeat a trip, these archived
waypoints can be reloaded into your GPS unit.
To create and save a Waypoint:
These first two techniques use the Quick Save method, the fastest and
easiest way to create a waypoint.
Create Waypoint at Current Position
While you are traveling, press WPT|WPT. The waypoint is saved and
automatically given a name with a sequential number, such as "way-
point 003." The waypoint symbol and number appear on the map.
NOTE:
The Quick Save method uses the default waypoint symbol until you
edit an existing waypoint and change its symbol. (Edit Waypoint
Symbol is described in Sec. 4.) After you have changed a waypoint
symbol, the unit will remember the one you chose and use it the
next time you "quick save" a waypoint. To revert back to the default
symbol, edit a waypoint and choose the original symbol, or use the
Reset Options command (described in Sec. 5).
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1.
Step 2.
Step 4.
Step 3.
Sequence for setting a waypoint. Step 1: while traveling, quickly press
WPT twice to call up Find Waypoint screen (seen in Step 2) and set a
point. Step 3: a message says the waypoint has been saved. Step 4: ve-
hicle continues on its way; number waypoint symbol is visible on map.
Create Waypoint on Map
1. Use the arrow keys to move the cursor to the place where you want
to make a waypoint.
2. Press WPT|WPT. The waypoint is saved and automatically given a
name with a sequential number, such as "waypoint 001." The waypoint
symbol and number appear on the map.
Create Waypoint by Entering a Position
1. Press WPT|↑ to MY WAYPOINTS|→ to NEW|ENT.
2. Press ↓ to ENTERED POSITION|ENT|↑ to CREATE|ENT.
3. Press ↓ to LATITUDE|ENT. Enter the latitude by pressing ↑ or ↓ to
change the first character, then press → to the next character and re-
peat until the latitude is correct. Press ENT.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press ↓ to LONGITUDE|ENT. Enter the longitude by pressing ↑ or ↓ to
change the first character, then press → to the next character and repeat
until the longitude is correct. Press ENT, then EXIT|EXIT to return to the
previous page display. The waypoint is saved and automatically given a
name with a sequential number, such as "waypoint 001." The waypoint
symbol and number appear on the map and in the waypoint list.
Navigate To a Waypoint
You can select any waypoint visible on the Map Page with the cursor,
then use the Navigate to Cursor command (we'll describe how later in
this section.) However, you can avoid scrolling the map to pick your
waypoint if you use the Find Waypoint commands:
1. Press WPT|↑ to MY WAYPOINTS|ENT. To look up the nearest waypoint,
press ↓ to NEAREST|ENT; or, to look by name (and scroll through the en-
tire waypoint list), press ENT. For this example, look by name.
2. If your waypoint list is a long one, you can spell out the waypoint name
in the FIND BY NAME box to search for it. (Press ↑ or ↓ to change the first
character, then press → to move the cursor to the next character and re-
peat until the name is correct, then press ENT to jump to the list below.)
3. If the list is short, you can jump directly to the FIND IN LIST box by
pressing ENT. Use ↑ or ↓ to select the waypoint name, press ENT and the
waypoint information screen appears with the GO TO command selected.
4. To begin navigating to the waypoint, press ENT.
Waypoint
Course line
(red)
Trail line
(magenta)
Off course
range, set at
0.15 mile
Destination
name
Navigation Page, navigating toward waypoint 001 and leaving a trail.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Man Overboard (MOB) Waypoint
One of boating's most terrifying events is having a friend or family
member fall overboard. This situation can be deadly on any body of wa-
ter — fresh or salt. It's particularly dangerous at night or if you're out
of sight of land. Of course, the first thing to do is remain calm and then
use all standard safety procedures to rescue the person.
This unit has a man overboard feature that shows navigation data to
the location where the feature was activated. To activate it, press the
ZOUT and ZIN keys at the same time. Your position at the time these
keys are pressed is used as the man overboard position.
Caution:
Saving a new "Man Overboard" waypoint will overwrite and
erase the previous "Man Overboard" waypoint.
Navigate Back to MOB Waypoint
Find your way back to the accident position with the Navigation Page
or Map Page. When MOB is activated, the Navigation Page automati-
cally shows the compass rose with its bearing arrow pointing toward
the man overboard position, and the destination name says "Going To
Man Overboard." The Map Page displays a Man Overboard waypoint,
represented by a human figure, and the steering arrow points where to
steer to reach that position.
Navigating to Man Overboard: "Man Overboard activated" message
shown at left. The Navigation Page is shown in the center and Map
Page is shown at right. The victim is astern of the vessel; the GPS
shows which direction to steer to for the rescue.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
The man overboard position is also stored in the waypoint list for future
reference. It can be edited the same as any other waypoint. This pre-
vents the inadvertent loss of the current Man Overboard position.
To cancel navigation to MOB, press MENU|MENU|↓ to CANCEL NAVIGA-
TION|ENT|← to YES|ENT. The unit stops showing navigation information.
Navigate to Cursor Position on Map
The GO TO CURSOR command: navigates to the current cursor position on
the map. It's a quick and handy way to navigate to anything you can
see on the map display.
1. Use the cursor (controlled by the arrow keys) with the zoom in and
zoom out keys to maneuver around the map until you find a location
you want to go to.
2. Center the cursor over the location to select it. See the example in
the following figure. (Many map items such as waypoints, Points of In-
terest, towns, etc. can be "selected," and appear "highlighted" with a
pop-up box. Other features, such as a river or a street intersection will
not appear "highlighted," but the cursor will take you to those locations
just the same.)
Navigate to cursor. In this example, the cursor has selected the town of
Oologah, Oklahoma.
3. Press MENU|ENT and the unit will begin navigating to the cursor lo-
cation.
The Map Page will display a red line from your current position to the cur-
sor position. The Navigation Page displays a compass rose showing naviga-
tion information to your destination. See the following examples.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
The 30-mile zoom figure at left clearly shows the red course line connect-
ing your current position to your destination. The 30-mile zoom, center,
shows both current position and direction to destination on screen. The
Navigation Page, right, will also show navigation information.
To stop navigating to the cursor, use the Cancel Navigation command:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT. The unit
stops showing navigation information.
Navigate to a Point of Interest
For POIs that are in view on the map, you can easily use the Navigate
to Cursor command above; just use the cursor to select the POI.
The other method involves searching for POIs with the Find Waypoint
command, launched with the WPT key. (See the searching example ear-
lier in this section, or turn to Sec. 6, Searching, for detailed instructions
on POI searches.)
After you have looked up an item with the Find Waypoint command,
use ← or → to make sure the GO TO command is highlighted at the bot-
tom of the screen, then press ENT. The unit begins showing navigation
information to the item.
To cancel navigation, press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|←
to YES|ENT. The unit stops showing navigation information.
Creating and Saving a Trail
A trail, or plot trail, is a string of position points plotted by the unit as you
travel. It's a travel history, a record of the path you have taken. Trails are
useful for repeating a journey along the same track. They are particularly
handy when you are trying to retrace your trip and go back the way you
came. On the screen, trails are represented by a solid line extending from
the back of the current position arrow. The default color is light magenta.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
The unit is set at the factory to automatically create and record a trail
while the unit is turned on. The unit will continue recording the trail
until the length reaches the maximum trail point setting (default is
2,000, but the unit can record trails 9,999 points long). When the point
limit is reached, the unit begins recording the trail over itself.
With the default auto setting, this unit creates a trail by placing a dot
(trail point) on the screen every time you change directions. (The methods
used for creating a trail and the trail update rate can both be adjusted or
even turned off. See Sec. 5 for Trail Options.)
To preserve a trail from point A to point B, you must "turn off" the trail
by making it inactive before heading to point C or even back to point A.
When the current trail is set inactive, the unit automatically creates
and begins recording a new trail.
To Save a Trail
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
Visible
Active
symbol
symbol
Sequence for saving a trail and beginning a new one. At left, My Trails
command. Center, the Trails Menu. The arrow to the right of Trail 3
indicates the trail is "active," and the check to the left indicates the
trail is visible on the map display. The right figure shows the Edit
Trail menu, with the Name command selected.
2. Press ↓ to the Active Trail Name|ENT.
3. Press ↓ to ACTIVE|ENT. This unchecks the Active option.
4. To return to the previous page, press EXIT|EXIT|EXIT|EXIT. As you
leave the Edit Trail menu, you will notice that a new trail starts with a
new sequential number. In the example figure below, the new trail is
number 4, showing zero points. Note that Trail 3 is inactive, but it is
still visible on the map.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
New trail, named "Trail 4," is created when Trail 3 is made inactive.
Any new travel will be recorded in this trail, which is active and visi-
ble. Trails do not need to be visible in order to be active.
You can save and recall up to 10 different plot trails, which can also be
copied to your MMC for archiving or for transfer to your MapCreate
software.
Tip:
Another quick way to stop recording one trail and begin a new one
is to use the New Trail command: Press MENU|MENU|↓ to MY
TRAILS|ENT|ENT.
Caution:
You also have the option of completely turning off trail record-
ing, under the trail Options command. However, if the Update
Active Trail option is left turned off, it will cancel the automatic
trail creation feature.
Displaying a Saved Trail
The active trail is automatically displayed on the map (the "Visible"
option) with the factory default settings. You can selectively turn trail
display off and on for any saved or active trail. In the Saved Trails List,
visible trails have a check mark in front of the trail name.
To turn off trail display:
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓|↓|↓ to enter the Saved Trail list, then use ↑ or ↓ to select
the desired Trail Name|ENT.
3. Press ↓ to VISIBLE|ENT. To return to the previous page, press
EXIT|EXIT|EXIT|EXIT.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn on trail display:
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓|↓|↓ to enter the Saved Trail list, then use ↑ or ↓ to select
the desired Trail Name|ENT.
3. Press ↓ to VISIBLE|ENT. To return to the previous page, press
EXIT|EXIT|EXIT|EXIT.
Navigating Trails
There are three methods for following a trail: visual trailing, navigating
a trail (forward) and backtracking a trail (backward). Try each method
to see which you prefer.
Visual trailing is the simplest method. It uses only the Map Page and
requires no menu commands at all. The technique works the same if
you are running a trail forward (from start to end) or backward (from
end to start.) However, visual trailing provides no navigation informa-
tion during the trip, such as the time to your destination.
The other two methods provide a full range of navigation data and work
with both the Map Page and Navigation Page. The only difference be-
tween them is "navigating a trail" follows a trail forward (from start to
end) while "backtracking" follows a trail in reverse (from end to start.)
When hiking at walking speed with a hand-held GPS, we often just use
visual back trailing because it is a bit better at following each little
turn on a foot path. At faster speeds, such as the highway or on the wa-
ter, the Navigate Trail and Backtrack Trail commands are handy.
Visual Trailing
1. On the Map Page, zoom (ZIN or ZOUT) so your trail is visible.
2. Begin moving and watch the Map Page. Simply walk or steer so that
your current position arrow traces along the trail you have just made.
Tip:
Generally, when using this method, the smaller the zoom range, the
more accurately you will be able to steer along the trail.
Navigate a Trail (forward)
The following figures illustrate the menu sequence for navigating a trail.
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓|↓|↓ to enter the Saved Trail list, then use ↑ or ↓ to select
the desired Trail Name|ENT.
3. Press ↓ to DELETE TRAIL|→ to NAVIGATE|ENT|ENT.
The unit begins showing navigation information along the trail.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
If you are already located at or near the beginning of your trail, the
arrival alarm will go off as soon as you hit Enter. Just press EXIT to
clear the alarm and proceed.
5. Now, begin moving and follow your unit.
6. When you reach your destination, be sure to cancel your navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT. The unit asks if you're
sure; press ←|ENT.
Figure 1.
Figure 2.
Figure 4.
Figure 3.
Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2,
Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with
Navigate Route command highlighted for Trail 1. A trail is always con-
verted to a "route" when you navigate the trail.
On the Map Page, the trail you are navigating is represented by a ma-
genta line (if the visible trail option is on). The course you are following
(the trail converted to a route) is represented by a red line. The magenta
trail line overlays the red course line. To see the red course line, you
54
Download from Www.Somanuals.com. All Manuals Search And Download.
much turn off the visible trail option. The Navigation Page will show
only the red course line, unless you are recording a new trail. The bear-
ing arrow on the compass rose points to the next waypoint on the trail.
As you travel, the arrival alarm will go off when you near a trail way-
point, and the bearing arrow on the compass rose will swing around
and point to the next trail waypoint. Press EXIT to clear the alarm.
North ꢀ
Present
position
arrow
Magenta
trail line
Trail point
Navigate trail, map views: at left driver is heading southeast straight
toward trail point 3. At right, driver has reached point 3 and has
turned southwest to follow the trail.
Track or compass heading indicator
Trail
Bearing arrow
waypoint
symbol
Cross track
error range
Red course
(off course
line made
indicator)
from trail
Magenta new
trail
Arrival
alarm
Navigate trail, navigation page (compass rose) views: At left, driver is
heading north straight toward trail point 2; bearing arrow shows the
trail point is 357 degrees (straight ahead.) At right, driver has reached
trail point 2 and must turn northeast to follow the trail. Arrival alarm
goes off and bearing arrow swings around to say turn right (east), to-
ward the next waypoint, trail point 3. The unit now shows navigation
information to point 3, which is 0.40 miles away.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigate a Back Trail (backtrack, or reverse)
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓|↓|↓ to enter the Saved Trail list, then use ↑ or ↓ to select
the desired Trail Name|ENT.
3. Press ↓ to DELETE TRAIL|→ to NAVIGATE|ENT.
4. Press → to REVERSE ROUTE|ENT|← to NAVIGATE ROUTE|ENT. The unit
begins showing navigation information along the trail, in reverse.
NOTE:
If you are already located at or near the end of your trail, the arri-
val alarm will go off as soon as you hit Enter. Just press EXIT to
clear the alarm and proceed.
5. Now, begin moving and follow your unit.
6. When you reach your destination, be sure to cancel your navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT. The unit asks if you're
sure; press ←|ENT.
Transfer Custom Maps and GPS Data Files
Custom Maps:
Custom maps work only from the MMC card or SD card. When a card
containing a Custom Map File is loaded into the unit, the unit auto-
matically loads the map into memory when the unit is turned on.
Instructions for copying Custom Map Files to an MMC are contained in
the instruction manual for your MMC card reader and MapCreate 6
software. For instructions on inserting an MMC into the unit, see Sec.
2, Installation/Accessories.
NOTE:
To load a Navionics chart, see Sec. 5 for the entry Navionics Charts.
GPS Data files:
GPS Data Files contain waypoints, routes, trails and event marker
icons. Instructions for copying GPS Data Files between your computer
and an MMC are contained in the instruction manual for your MMC
card reader and MapCreate 6 software.
GPS data automatically recorded in the unit's internal memory must be
saved to the MMC (as a GPS Data File) in order to store it on your per-
sonal computer. GPS Data Files stored on an MMC must be copied from
the card to the unit's internal memory before the unit can read them.
Here's how:
1. Insert the MMC into your unit. Press MENU|MENU|↓ to SYSTEM
SETUP|ENT|↓ to TRANSFER MY DATA|ENT and the screen below appears.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
The Transfer My Data submenu asks if you want to save data to the
MMC or load data from the MMC into the unit's memory.
2. The Transfer My Data menu includes a message which tells you if an
MMC is present or not. If no MMC is present, you must first insert a
card into the unit in order to activate the Load or Save commands.
To transfer data from the unit to the MMC: press ENT (for SAVE.)
To transfer data from the MMC to the unit: press → to LOAD|ENT.
3. Saving to MMC: To accept the default name "Data" for the GPS
Data File, press ↓ to SAVE DATA|ENT. If you wish to rename the file (as
shown in the following figures), press ENT to activate the selection box.
Press ↑ or ↓ to change the first character, then press → to the next
character and repeat until the name is correct. Then, press ENT|↓ to
SAVE DATA|ENT.
The unit will display first a progress then a completion message when
the data transfer is finished. To return to the Page view, repeatedly
press EXIT.
From left to right, these figures show the menu sequence for naming
and saving a GPS Data File from the unit's memory to an MMC.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Loading to unit memory: There may be more than one GPS Data
File (*.USR) on the card. To select a file, press ENT to activate the selec-
tion box, use ↓ or ↑ to highlight the file, then press ENT to accept the
selection. Next, press ↓ to LOAD DATA|ENT. The unit will display a com-
pletion message when the data transfer is finished. To return to the
Page view, press EXIT|EXIT|EXIT|EXIT.
Figure 2.
Figure 1.
Figure 3.
Figure 4.
These figures show the menu sequence for loading a GPS Data File
from an MMC into the unit's memory.
Cancel Navigation
You can turn off any of the navigation commands after you reach your
destination or at any other time by using the Cancel Navigation com-
mand. Press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4:
Advanced GPS Operations
Find Distance From Current
Position To Another Location
1. While on the Map Page press: MENU|↓ to FIND DISTANCE|ENT.
2. Center your cursor over the position you want to find the distance to.
A rubber band line appears, connecting your current position to the
cursor's location. The distance along that line will appear in a pop-up
box. The box also shows the bearing to the point you're measuring to.
3. Press EXIT|EXIT to return to regular operation.
At left, the distance from the boat's current position to the cove is 5.78
miles. At right. the distance from Houston to New Orleans is 316.9 miles.
Find Distance From Point to Point
You can also measure distance between two other points on the map.
1. While on the Map Page press: MENU|↓ to FIND DISTANCE|ENT.
2. Center your cursor over the first position. (A rubber band line ap-
pears, connecting your current position to the cursor's location.) Press
ENT to set the first point, and the rubber band line disappears.
3. Move the cursor to the second position. The rubber band line reap-
pears, connecting the first point you set to the cursor. The distance
along that line will appear in the pop-up box.
4. Press EXIT to clear the command and return to the page screen.
(Press EXIT once more to clear the cursor.)
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Icons
Icons are graphic symbols used to mark some location, personal point of
interest or event. They can be placed on the map screen, saved and re-
called later for navigation purposes. These are sometimes referred to as
event marker icons. This unit has 42 different symbols you can pick
from when creating an icon.
Icons are similar to waypoints, but they do not store as much informa-
tion (like names) as waypoints do. You can't use a menu to navigate to
icons as you can with waypoints. (But, you can use the map cursor and
navigate to any icon on the map.)
You can create an icon at the cursor position on the map, or at your
current position while you are navigating.
Create Icon on Map
1. Use the arrow keys to move the cursor to the place where you want
to make an icon.
2. Press ENT and the screen shows a "Select Icon Symbol" menu.
3. Press ← or ↑ or → or ↓ to select your icon symbol, then press ENT.
The icon appears on the map. Press EXIT to clear the cursor.
Cursor selects icon location, left; Select Icon Symbol menu, center;
Boat Ramp icon on map, right. (Cursor has been moved for clarity.)
Create Icon at Current Position
1. While you are traveling, press ENT and the screen shows a "Select
Icon Symbol" menu.
2. Press ← or ↑ or → or ↓ to select your icon symbol, then press ENT.
The icon appears on the map.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Delete an Icon
You can delete all the icons at one time, you can delete all icons repre-
sented by a particular symbol, or you can use the cursor to delete a se-
lected icon from the map.
1. Press MENU|↓ to DELETE MY ICONS|ENT.
2. Press ↓ to DELETE ALL ICONS, DELETE BY SYMBOL, or DELETE FROM MAP and
press ENT.
Delete icons menu.
The Delete All Icons command will ask if you are sure. Press ← to
YES|ENT. All icons will be deleted from the map.
The Delete by Symbol command will launch the Select Symbol menu.
Press ← or ↑ or → or ↓ to select the icon symbol to delete, then press
ENT. A message appears saying all icons with the selected symbol have
been deleted.
The Delete From Map command will prompt you to move the cursor
over an icon to select it. After selecting the icon, press ENT and it disap-
pears from the map.
Navigate to an Icon
Use the Navigate to Cursor command, and use the cursor to select the
desired icon on the map.
1. Use arrow keys to center cursor cross-hair over the icon.
2. To navigate to the selected icon location: press MENU|ENT|EXIT.
Follow course line on the Map Page or the compass bearing arrow on the
Navigation Page.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Routes
A route is a series of waypoints, linked together in an ordered sequence,
that's used to mark a course of travel. You can visualize a route as a
string of beads: The beads represent waypoints and the string repre-
sents the course of travel connecting waypoint to waypoint.
The course from one waypoint to the next is a leg; routes are composed
of one or more legs. The legs of all GPS routes are based on straight
lines between waypoints.
A route provides the automatic capability to navigate through several
waypoints without having to reprogram the unit after arriving at each
waypoint. Once programmed into the GPS unit, a route provides the
option of navigating forward through the route waypoints or in reverse
order (you can even begin navigating in the middle of a route!)
Create and Save a Route
You have the option of creating and editing a route in the unit, or you
can make a route on your computer with our MapCreate 6 software.
PC-created Routes
MapCreate is the easiest method for preparing a route, simply because
your PC's larger screen, keyboard and mouse are easier to manipulate
than the unit.
To load a MapCreate route into the unit, follow instructions in MapCre-
ate's manual for creating a route and saving it as part of a GPS Data File
(file format *.usr). Copy the GPS Data File to an MMC and insert the
MMC in the unit. (See Sec. 2 for instructions on installing MMCs. To
load the GPS Data File into the unit's memory, see the entry on Transfer
Custom Maps & GPS Data Files in Sec. 3, Basic GPS Operations.)
Routes Created in the Unit
You can create a route by selecting existing waypoints from the way-
point list or you can set a series of route waypoints on the map with
cursor arrows and the Enter key. In this example, we'll create a route
from the map.
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE,
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Route Planning command on Main Menu, left,
will open the Route List screen, right.
2. If necessary, press ↑ to select NEW ROUTE, then press ENT. (To add to
an existing route, press ↓ or ↑ to route name|ENT.)
3. Press ↓ to (ROUTE END)|ENT|↓ to ADD FROM MAP|ENT. The Map Page
appears with the cursor showing.
Edit Route menu, left. Edit Route Waypoints menu, right,
with Add From Map command selected.
4. Use the Zoom keys and arrow keys to move the map and cursor until
the cursor is centered on the spot where you want your route to begin.
(If you are starting at your current position or the current cursor posi-
tion, you are already at the starting spot.)
5. Set the first route waypoint: press ENT. In this example, we moved to
the entrance of the cove where our boat was docked to start out route a
promising fishing spot next to an oil platform. (Creating this example
route is illustrated in the following figures.)
63
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
1.
1.
2.
3.
2.
Route creation sequence, from left: Fig. 1. Set route waypoint (1) at the
cove entrance. Fig. 2. Move cursor northeast to set point (2) at channel
entrance. Fig. 3. With point (2) set, move cursor southeast to mark
channel exit with waypoint (3). In figures 2 and 3, notice the rubber
band line extending from the previously set waypoint to the cursor.
This line will become the course for the route.
6.
4.
5.
Route creation sequence, continued: Fig. 4. Point (3) set at channel mouth.
Fig. 5. Waypoint (4) set further south along the beach, at a recognizable
landmark (Bob Hall Pier). Waypoint PLFM Q W ends the route at an oil
platform some distance from the shore. Fig. 6. Press EXIT to save the route
and you return to this screen.
6. Move the cursor to the next point in the route, a spot where you need
to turn or change direction, and press ENT to set the next waypoint.
7. Repeat step six until the route reaches your destination.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
8. To save your route, press EXIT. The unit reverts to the Edit Route
screen, with the route automatically named "Route 1" and stored in the
unit's internal memory.
You can edit the route and run other commands, but if you are finished
with the route for now, return to the last page displayed by
pressing EXIT|EXIT|EXIT.
NOTE:
When adding waypoints to an existing route, the inserted way-
points will appear in the route in front of the waypoint you have
selected in the Edit Route menu. To insert waypoints at the end of
the route, make sure to select (ROUTE END) before adding them.
Delete a Route
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to route name|ENT.
3. Press → to DELETE ROUTE|ENT|← to YES|ENT.
Tip:
You can also delete all routes at once:
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press → to DELETE ALL|ENT|← to YES|ENT.
Edit a Route Name
You can edit the route name if you wish.
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to route name|ENT|→ to EDIT ROUTE NAME|ENT.
3. Press ↑ or ↓ to change the first character, then press → to move the
cursor to the next character and repeat until the name is correct, then
press
ENT.
Return to the previous page by pressing
EXIT|EXIT|EXIT|EXIT.
Edit Route Waypoints
You can edit the route by adding and removing waypoints.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to route name|ENT|↓ to Route Waypoints List. Use ↓ and ↑
to select a waypoint, then press ENT.
Edit Route Waypoints menu.
3. Use ↓ and ↑ to select a command from the Edit Route Waypoints
menu and press ENT. Add From Map lets you insert a waypoint in the
route by clicking on a map location with the cursor. Add Waypoint calls
up the Waypoint List so you can insert a waypoint from the list. Re-
move Waypoint will delete the waypoint from the route. View Waypoint
will show you where the selected waypoint is on the map.
NOTE:
When adding waypoints to a route, the inserted waypoints will ap-
pear in the route in front of the waypoint you have selected. To in-
sert waypoints at the end of the route, make sure to select (ROUTE
END) before adding them.
Navigate a Route
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE,
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Route Planning command on Main Menu, left; Routes menu, center;
Edit Route menu, right. Navigate Route command is selected.
2. Press ↓ to select route name|ENT|ENT.
3. Upon arrival at your destination, cancel navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
The following figures show what the Navigation Page and Map Page
look like while navigating a route.
Navigate a Route in Reverse
Here's how you run a route backward, from the end waypoint to the
beginning waypoint:
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE,
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to select route name|ENT|→ to REVERSE ROUTE|ENT|← to
NAVIGATE ROUTE|ENT.
3. Upon arrival at your destination, cancel navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.
Figure 1.
Navigating along a route: Fig. 1 shows the Navigation Page at the start
of a route, heading straight for the first waypoint (Wpt 1). In Fig. 2, the
traveler has arrived at Wpt 1; the arrival alarm has been triggered and
the bearing arrow on the compass rose has turned to point toward Wpt
2, off to the northeast.
Figure 4.
Figure 3.
In Fig. 3 the traveler has turned northeast on his new course and is
heading straight for Wpt 2, which is 0.27 miles away. Fig. 4 shows route
navigation on the Map Page. In this figure, the traveler has reached Wpt
2 and is starting on the leg between Wpts 2 and 3.
Trails
Delete a Trail
This is the command used to erase or delete
a
trail:
Press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail name|ENT|↓ to
DELETE TRAIL|ENT|← to YES|ENT.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip:
You can also delete all trails at once:
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press → to DELETE ALL|ENT|← to YES|ENT.
Edit a Trail Name
To edit a trail name: press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail
name|ENT|ENT. Press ↑ or ↓ to change the first character, then press
→ to the next character and repeat until the name is correct. Press ENT
then EXIT|EXIT|EXIT|EXIT to return to the previous page display.
Tip:
You can quickly call up the Edit Trail menu by selecting a trail on
the map with the cursor. Simply move the cursor over a trail and a
pop-up box appears. Press WPT and the Edit Trail menu opens.
At left, trail selected with map cursor. The box at the bottom of the
screen shows distance and bearing from current position to the se-
lected point on the trail. At right, the Edit Trail menu.
Edit a Trail Color
To edit a trail color: press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail
name|ENT|↓ to COLOR|ENT. Press ↑ or ↓ to select a color style, then press
ENT. Press EXIT|EXIT|EXIT|EXIT to return to the previous page display.
Edit a Trail Pattern
To edit a trail pattern: press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail
name|ENT|↓ to PATTERN|ENT. Press ↑ or ↓ to change the first character,
then press → to the next character and repeat until the pattern is cor-
rect. Press ENT, then EXIT|EXIT|EXIT|EXIT to return to the previous
page display.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
At left, Edit Trail Menu with Pattern option selected. At right, edited
trail with dotted line pattern.
Utilities
Utilities are useful tools for traveling or for outdoor activities.
Alarm Clock
To get to the alarm clock menu: press MENU|MENU|↓ to TIMERS|ENT|↓
to ALARM CLOCK|ENT.
Sun/Moon Rise & Set Calculator
To get to the Sun/Moon menu: press MENU|MENU|↓ to SUN/MOON
CALCULATIONS|ENT.
Trip Calculator
To get to the Calculator menu: press MENU|MENU|↓ to TRIP CALCULA-
TOR|ENT.
Trip Down Timer
To get to the Down Timer menu: press MENU|MENU|↓ to TIMERS|ENT|↓
to DOWN TIMER|ENT.
Trip Up Timer
To get to the Up Timer menu: press MENU|MENU|↓ to TIMERS|ENT|ENT.
Waypoints
Delete a Waypoint
To delete a waypoint from the waypoint list: press WPT|↑ to MY
WAYPOINTS|ENT|ENT|ENT|↓ to waypoint name|ENT|→ to DELETE
WAYPOINT|ENT|← to YES|ENT. To return to the previous page, press
EXIT|EXIT.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
To delete a waypoint from the map:
1. Use the arrow keys to select the waypoint with the cursor.
2. Press WPT|→ to DELETE WAYPOINT|ENT|← to YES|ENT. To return to
the previous page and clear the cursor, press EXIT.
To delete all waypoints at one time: press MENU|MENU|↓ to SYSTEM
SETUP|ENT|↓ to DELETE ALL MY WAYPOINTS|ENT|← to YES|ENT. To return
to the previous page, press EXIT|EXIT.
Edit a Waypoint
Waypoint Name
To edit waypoint name:
1. Press WPT|↑ to MY WAYPOINTS|ENT|ENT|ENT|↓ to waypoint
name|ENT|→ to EDIT WAYPOINT|ENT|ENT.
2. Press ↑ or ↓ to change the first character, then press → to the next
character and repeat until the name is correct. Press ENT then
EXIT|EXIT|EXIT|EXIT to return to the previous page display.
Waypoint Symbol
To edit waypoint symbol:
1. Press WPT|↑ to MY WAYPOINTS|ENT|ENT|ENT|↓ to waypoint
name|ENT|→ to EDIT WAYPOINT|ENT|↓ to ALTITUDE|→ to CHOOSE SYM-
BOL|ENT.
2. Use arrow keys to select desired symbol and press ENT. To return to
the previous page, press EXIT|EXIT|EXIT|EXIT.
Waypoint Position
To edit waypoint position:
1. Press WPT|↑ to MY WAYPOINTS|ENT|ENT|ENT|↓ to waypoint
name|ENT|→ to EDIT WAYPOINT|ENT.
2. Latitude: press ↓ to LATITUDE|ENT. Press ↑ or ↓ to change the first
character, then press → to the next character and repeat until the lati-
tude is correct. Press EXIT.
3. Longitude: press ↓ to LONGITUDE|ENT. Press ↑ or ↓ to change the first
character, then press → to the next character and repeat until the lon-
gitude is correct. Press EXIT.
4. When latitude and longitude are correct, return to the previous page:
press EXIT|EXIT|EXIT|EXIT.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Waypoint
To select a waypoint on the map (for navigating to, for editing, etc.,) use
the arrow keys and center the cursor over the waypoint. A highlighted
halo will appear around the waypoint.
Set a Waypoint by Average Position
This feature sets a waypoint at the current position after taking several
position readings and averaging them. This boosts waypoint position
accuracy by helping to eliminate errors caused by atmospheric condi-
tions and other factors.
1. Press WPT|↑ to MY WAYPOINTS|→ to NEW|ENT.
2. Press ↓ or ↑ to AVERAGE POSITION|ENT|press ↑ to CREATE|ENT.
3. Wait while the unit takes points to average for the position. (The greater
the number of points, the greater the accuracy.) When the desired number
of points accumulates, press ENT to create and save the waypoint.
4. The Edit Waypoint menu appears. You can simply save the waypoint
by pressing EXIT|EXIT or you can edit the waypoint.
Set a Waypoint by Projecting a Position
This feature sets a waypoint at a point located a specific distance and
bearing from a reference position. The reference position can be se-
lected from your waypoint list, a map feature or from the Points of In-
terest list.
1. Press WPT|↑ to MY WAYPOINTS|→ to NEW|ENT.
2. Press ↓ to PROJECTED POSITION|ENT|↑ to CREATE|ENT.
3. Press ↓ to CHOOSE REFERENCE|ENT. Use ↑ and ↓ to select a waypoint,
map feature or Point of Interest. When the point has been selected,
press ENT and the point's position appears as the reference position.
4. Press ↓ to DISTANCE|ENT. Press ↑ or ↓ to change the first character,
then press → to the next character and repeat until the distance is cor-
rect. Press ENT.
5. Press ↓ to BEARING|ENT. Press ↑ or ↓ to change the first character,
then press → to the next character and repeat until the bearing is cor-
rect. Press ENT.
6. Press ↑ to PROJECT|ENT. The Edit Waypoint menu appears. You can
simply save the new projected waypoint by pressing EXIT|EXIT or you
can edit the waypoint. (Press EXIT|ENT if you want to immediately be-
gin navigating to the new waypoint.)
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5:
System & GPS Setup Options
Alarms
This unit has several GPS alarms. The factory default setting has all of
these but the anchor alarm turned on. You can turn the alarms off and
on and change their distance settings.
You can set an arrival alarm to flash a warning message and sound a
tone when you cross a preset distance from a waypoint. For example, if
you have the arrival alarm set to .1 mile, then the alarm will flash a
message when you come within .1 mile of the recalled waypoint.
The off course alarm warns you when your track drifts too far to the
right or left of the course line to the waypoint. For example, if the
alarm is set to .1 mile, then the alarm flashes a message if you drift .1
of a mile or more to the right or left of the line to the waypoint.
The anchor alarm is triggered when you drift outside of a preset radius.
Again, using the .1 mile as an example, if you're anchored and your
boat moves more than .1 of a mile, the alarm will flash a message and
sound a tone.
Alarms command, left; Alarm menu, right.
To change alarm settings:
1. Press MENU|MENU|↓ to ALARMS|ENT|ENT.
2. Scroll ↓ or ↑ to select the desired category, then press ENT to check or
clear the Enabled box. This turns the alarm on (checked) or off (un-
checked.)
73
Download from Www.Somanuals.com. All Manuals Search And Download.
3. To change distance settings, scroll ↓ or ↑ to select the desired cate-
gory, then press → |ENT to activate the distance dialog box. Press ↑ or
↓ to change the first character, then press → to the next character and
repeat until the name is correct.
4. When your adjustments are finished, return to the last page dis-
played by repeatedly pressing EXIT.
IMPORTANT ALARM NOTES:
Anchor Alarm - The anchor alarm may be triggered even when
you're sitting still. This typically happens when using small (less
than .05 mile) anchor alarm ranges.
Arrival Alarm - If you set the arrival alarm's distance to a small
number and you run a route (see the Navigate Routes segment),
this unit may not show navigation data to the next waypoint, once
you arrive at the first one, since you may not be able to come close
enough to the first waypoint to trip the arrival alarm.
Check MMC Files and Storage Space
To check MMC Files:
Press MENU|MENU|↓ to BROWSE MMC FILES|ENT. Press ↓ to MMC CARD
INFO|ENT to see the free space on the card.
Main Menu, left, MMC File Browser, right.
Communications Port Configuration
The unit has one NMEA 0183 version 2.0 compatible communication
port, or com port for short. The Com Port Menu, which is accessed from
the System Setup Menu, allows you to configure the communications
port to send or receive data to another electronic device, such as an
autopilot. The com port can be used for either NMEA or SiRF Binary
data transfer.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Menus for changing Com Port settings.
For connectors and wiring information for another device, see page 20.
For assistance in configuring the unit to communicate with another
device, consult the factory; customer service phone numbers are in the
back of this manual. Also see the entry below for Configure NMEA. To
set Com Port Configuration:
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT.
2. Press ↓ to COMMUNICATIONS PORT|ENT.
Configure NMEA
You can configure the unit to use specific NMEA sentences.
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT.
2. Press ↓ to COMMUNICATIONS PORT|ENT|↓ to CONFIGURE NMEA|ENT.
3. A menu appears showing the prefixes of the available NMEA sen-
tences. A check mark next to a prefix means the prefix is in use. Use ↑
↓ → ← to select a prefix, then press ENT to turn off the prefix. (Press
ENT again to check the box and turn a prefix on.)
NOTE:
The names of the NMEA sentences are abbreviated in this menu.
These are the functions of the various selectable prefixes:
•
GLL transmits latitude and longitude of present position, time
of position fix, and status.
•
•
RMC and RMB transmits navigation information messages.
APB transmits autopilot information.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
GGA transmits time, position, and fix related data.
GSA and GSV transmits fix mode, DOP values, and satellites in
view information.
•
•
•
•
DBT transmits the depth below the transducer.
DPT transmits the depth
MTW transmits the water temperature.
VLW transmits the distance traveled through water as meas-
ured by the paddle wheel.
•
VHW transmits the water speed as measured by the paddle
wheel.
4. When the desired prefixes are checked or unchecked, press
EXIT|EXIT|EXIT|EXIT to return to the previous page.
Coordinate System Selection
The Coordinate System Menu lets you select the coordinate system to
use when displaying and entering position coordinates.
Menus for changing coordinate system used to display positions.
To get to Coordinate System Selection:
1. Press MENU|MENU|↓ to GPS SETUP|ENT.
2. Press ↓ to COORDINATE SYSTEM|ENT.
This unit can show a position in degrees (36.14952°); degrees, minutes
and thousandths of a minute (36° 28.700'); or degrees, minutes, seconds
and tenths of a second (36° 28' 40.9"). It can also show position in: UTM
76
Download from Www.Somanuals.com. All Manuals Search And Download.
(Universal Transverse Mercator) projection; MGRS (Standard); MGRS
(Standard + 10); Map Fix; Loran TD; British, Irish, Finnish, German,
New Zealand, Swedish, Swiss, Taiwan and Greek grid systems.
UTM's are marked on USGS topographic charts. This system divides
the Earth into 60 zones, each 6 degrees wide in longitude.
British, Irish, Finnish, German, New Zealand, Swedish, Swiss, Taiwan,
and Greek grid systems are the national coordinate system used only in
their respective countries. In order to use these grid systems, you must
be in the respective country. This unit will pick the matching datum for
you when you select the grid. See the entry on Map Datum Selection for
more information.
The Military Grid Reference System (MGRS) uses two grid lettering
schemes, which are referred to as standard and standard + 10 MGRS
on this unit. Your position and datum in use determines which one to
use. If you use standard, and your position is off significantly, then try
the alternate.
NOTE: When the position format is changed, it affects the way all posi-
tions are shown on all screens. This includes waypoints.
To change the coordinate system, press ENT while COORDINATE SYSTEM is
highlighted. Press the ↑ or ↓ arrow keys to highlight the desired for-
mat. Press ENT to select it. Press EXIT to erase the menus.
To setup Loran TD:
NOTE:
If the Loran TD conversion is chosen, you must enter the local Lo-
ran chain identification for the master and slaves. Do this by se-
lecting "Setup Loran TD" at the bottom of the "Coordinate System"
menu and select the ID. Press EXIT to erase this menu.
Configure Loran TD menu.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Map Fix
Map Fix is used with charts or maps. This system asks for a reference
position in latitude/longitude, which you take from a marked location
on the map. It then shows the present position as distance on the map
from that reference point.
For example, if it shows a distance of UP 4.00" and LEFT 0.50", you
then measure up three inches and to the left a half-inch from the refer-
ence point on the map to find your location.
To configure a map fix:
To use this format, you need to follow these steps in order. First, take
your map of the area and determine a reference latitude/longitude.
(Note: in order for this system to work, the latitude/longitude lines
must be parallel with the edge of the map. USGS maps are parallel,
others may not be. Also, this works better with smaller scale maps,
such as 1:24000.) The reference position can be anywhere on the map,
but the closer it is to your location, the smaller the numbers will be
that you'll have to deal with.
Once you've decided on a reference position, you can save it as a waypoint.
See the waypoint section for information on saving a waypoint. Save the
reference position as a waypoint. Exit from the waypoint screens.
1. Press MENU|MENU|↓ to GPS SETUP|ENT.
2. Press ↓ to COORDINATE SYSTEM|ENT.
3. Press ↓ to SETUP MAP FIX|ENT.
The screen below appears, and MAP SCALE is highlighted. Press ENT and
enter the map's scale. This is generally at the bottom of the paper map.
It's shown as a ratio, for example 1:24000. Press EXIT and the unit re-
turns to the Configure Map Fix screen.
Configure a map fix so the unit can find your position on a printed
chart or topographical map.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Press → to SELECT ORIGIN|ENT|ENT|ENT to bring up the waypoint list.
Select the waypoint (or a landmark of POI) that you saved the reference
point under and press ENT. The unit displays a waypoint information
screen with the command SET AS ORIGIN selected; press ENT and the unit
returns to the Configure Map Fix menu. Finally, press EXIT to erase
this menu. Now press ↑ to COORD SYSTEM|ENT, select MAP FIX from the
list and press ENT|EXIT. All position information now shows as a dis-
tance from the reference point you chose.
Customize Page Displays
The Satellite Status, Navigation, and Map pages all have customizable
options. These options decide which information is viewable on each page.
Customize Satellite Status Page
While on the Satellite Status Page, press MENU|↓ to CUSTOMIZE|ENT.
Press ← or → to select a data box. With the data box highlighted and
flashing, press ENT to open a list of options. Scroll ↑ and ↓ to select a
different data option, then press ENT. After all options are set, press
EXIT to return to the page display.
Customize Navigation Page
While on the Navigation Page, press MENU|↓ to CUSTOMIZE|ENT. Press ↓
or ↑ to select a data box. With the data box highlighted and flashing,
press ENT to open a list of options. Scroll ↑ and ↓ to select a different
display option, then press ENT. After all options are set, press EXIT to
return to the page display.
Customize Map Page
While on the Map Page, press PAGES|↓ or ↑ to select Option
Name|EXIT.
GPS Simulator
The GPS simulator lets you use the unit as if you were outdoors navi-
gating somewhere. It's a great way to practice using your unit. You can
set the starting location by entering latitude/longitude (Starting Posi-
tion) or from a stored waypoint, map place or POI location (CHOOSE START
command). You can steer your position and change speed on the map by
using the arrow keys (STEER WITH ARROWS command) or by setting the track
and speed in the dialog boxes provided on the simulator menu screen.
To get to the GPS Simulator:
1. Press MENU|MENU|↓ to GPS SETUP|ENT.
2. Press ↓ to GPS SIMULATOR|ENT. The GPS Simulator Menu appears.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS Setup Menu, left; GPS Simulator menu, center.
Map Page showing Track and Speed steering arrow indicators, right.
In this example, you are "traveling" across Mudisland Point
on a track of 19º at a speed of 50 miles per hour.
Make the desired settings, then turn the simulator on by highlighting
the GPS SIMULATOR ON box and pressing ENT key. Press EXIT|EXIT|EXIT
to erase this menu. A message and tone appear periodically, warning
you that the simulator is on. To turn the simulator off, repeat the above
steps or turn the unit off.
While in simulator mode, you can press EXIT to clear the steering and
speed boxes from the screen while continuing the simulation. This will
allow you to use the map cursor during a simulation. To turn steering
and speed boxes back on again, return to the GPS Simulator menu, se-
lect the STEER WITH ARROWS command, press ENT, then Press
EXIT|EXIT|EXIT to return to the previous page.
Simulating Trail or Route Navigation
In Simulator mode, your unit can automatically follow a trail or route
without manual steering if you use these steps:
1. From the Map Page, go to the simulator menu. Pick a STARTING PO-
SITION at or near the beginning of your trail/route. Enter an approximate
TRACK (shown in compass degrees) that will point you toward the start
of the trail/route.
2. Set SPEED to zero. Select STEER WITH ARROWS command and press ENT,
which turns on the simulator and returns you to the Map Page.
3. Begin navigating along the trail/route. (If you are close enough to the
first waypoint, the arrival alarm will usually go off as soon as naviga-
80
Download from Www.Somanuals.com. All Manuals Search And Download.
tion begins. Press EXIT to clear the alarm.) When navigation starts,
press ↑ to increase speed to the desired setting.
4. Press EXIT to turn off the steering and speed boxes. The unit will now
automatically "steer" along the trail or route. When you arrive at your
"destination," cancel navigation as you normally do.
Tip:
You can pick any spot on the map to begin your simulation session
by using the Initialize GPS command. This makes your unit think
it's located at the position you select. See its entry following the en-
try for Hide GPS Features.
Initialize GPS
This command is handy when you are practicing in simulator mode. (See
the entry in this section for GPS Simulator.) In simulator mode, this
command makes the unit operate as if it is sitting someplace other than
its actual location. So, you and your unit could be located in Kansas City,
but easily practice navigating in the ocean off Islamorada, Florida.
1. Press MENU|MENU|↓ to GPS SETUP|ENT|ENT.
2. A message appears, telling you to move the cursor near the desired
location and press ENT. When the message automatically clears, follow
the message instructions.
3. In a moment, your present position marker arrow appears on the
map in the location you selected with the cursor. The unit will consider
that spot as its last known position until changed by either a live satel-
lite lock-on or a new simulator location.
Map Auto Zoom
This receiver has an auto zoom feature that eliminates much of the but-
ton pushing that other brands of GPS receivers force you to make. It
works in conjunction with the navigation features.
First, start navigation to a waypoint. (See the waypoint section for
more information on navigating to a waypoint.) Then, with the auto
zoom mode on, the unit zooms out until the entire course shows, from
the present position to the destination waypoint. As you travel toward
the destination, the unit automatically begins zooming in — one zoom
range at a time — always keeping the destination on the screen.
To turn this feature on, from the MAP PAGE, press MENU|↓ to AUTO
ZOOM|ENT|EXIT. Repeat these steps to turn it off.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Map Data
This menu lets you turn the map off, if desired (which turns the map
screen into a GPS plotter); turn off or on the pop-up map info boxes;
draw the map boundaries or boxes around the areas of high detail; or
fill land areas with gray. You can also turn on or off Map Overlays,
which display latitude and longitude grid lines or range rings on the
map. This menu lets you select Navionics Maps; for instructions, see
the Navionics Charts entry in this section.
To get to Map Data:
From the Map Page, press MENU|↓ to MAP DATA|ENT.
Map Menu, left, Map Data Menu, right.
Show Map Data
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ENT to enter
the EARTH MAP DETAIL selection list, and choose how much detail you
want, from Off (so the unit operates like a GPS plotter) to High. After
the option is set, press EXIT repeatedly to return to the page display.
Pop-up Map Information
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ to POPUP
MAP INFORMATION. With the option highlighted, press ENT to check it (turn
on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to
return to the page display.
Map Boundaries
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ to DRAW
MAP BOUNDARIES. With the option highlighted, press ENT to check it (turn
on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to
return to the page display.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Fill Water With White
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ to FILL
WATER WITH WHITE. With the option highlighted, press ENT to check it
(turn on) and uncheck it (turn off.) After the option is set, press
EXIT|EXIT to return to the page display.
Map Overlays (Range Rings; Lat/Long Grid)
The map screen can be customized with four range rings and/or grids
that divide the plotter into equal segments of latitude and longitude.
Range rings are handy for visually estimating distances on the map. The
ring diameters are based on the current zoom range. For example: at the
100 mile zoom, the screen will show two rings with your current position
in the center. The large ring touching the left and right sides of the
screen is 100 miles in diameter (same as the zoom range). The second
smaller ring is 50 miles in diameter (always 1/2 the zoom range).
The distance from your current position to the smaller ring (the ring's
radius) is 25 miles (always 1/4 the zoom range). With the arrow keys
and map cursor, you can scroll the map to see the third and fourth
rings. In this example, the distance to the third ring is 75 miles and
distance to the fourth ring is 100 miles from your current position.
To set range rings: From the Map Page, press MENU|↓ to MAP
DATA|ENT. Press ↓ to RANGE RINGS. With the option highlighted, press ENT
to check it (turn on) and uncheck it (turn off.) After the option is set,
press EXIT|EXIT to return to the page display.
To set Lat/Long Grid: From the Map Page, press MENU|↓ to MAP
DATA|ENT. Press ↓ to LAT/LON GRID LINES. With the option highlighted,
press ENT to check it (turn on) and uncheck it (turn off.) After the op-
tion is set, press EXIT|EXIT to return to the page display.
Map Datum Selection
Maps and charts are based on a survey of the area that's covered by the
map or chart. These surveys are called "Datums." Maps that are cre-
ated using different datums will show the same latitude/longitude in
slightly different locations.
All datums are named. The GPS system is based on the WGS-84 da-
tum, which covers the entire world. Other datums may also cover the
entire world, or just a small portion of it. By default, your position
shows using the WGS-84 datum. However, it can show your position
using one of 191 different datums. Different datums can be selected; to
change the datum:
1. Press MENU|MENU|↓ to GPS SETUP|ENT|↓ to DATUM SELECTION|ENT.
2. Scroll ↓ or ↑ to select the desired datum, then press ENT.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
3. To return to the last page displayed, press EXIT|EXIT.
A list of the datums used by this unit is in the back of this manual.
GPS Setup Menu, left, Map Datum Menu, right.
Map Detail Category Selection
This menu determines which of the mapping features are shown on the
screen. This includes, waypoints, trails, icons, cities, highways, etc. You
can selectively turn on or off any of these items, customizing the map to
your needs.
To get to Map Categories:
1. From the Map Page, press MENU|↓ to MAP CATEGORIES DRAWN|ENT.
2. Press ↑ or ↓ to select a category or press → or ← to select a subcate-
gory. Press ENT to turn it off (no check) or on (checked.)
3. To return to the last page displayed, press EXIT|EXIT.
Map Menu, left, Map Categories Drawn Menu, right.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Map Orientation
By default, this receiver shows the map with north always at the top of
the screen. This is the way most maps and charts are printed on paper.
In Track Up mode, map shows "N" and arrow to indicate north.
Map orientation at left is shown in north up and at right, track up.
This is fine if you're always traveling due north. What you see to your
left corresponds to the left side of the map, to your right is shown on
the right side of the map, and so on. However, if you travel any other
direction, the map doesn't line up with your view of the world.
To correct this problem, a track-up mode rotates the map as you turn.
Thus, what you see on the left side of the screen should always be to
your left, and so on.
Another option is course-up mode, which keeps the map at the same
orientation as the initial bearing to the waypoint. When either the
track-up or course-up mode is on, an "N" shows on the map screen to
help you see which direction is north.
To change map orientation: from the Map Page, press MENU|↓ to MAP
ORIENTATION|ENT. Use ↑ or ↓ to select the desired mode, then press ENT.
Press EXIT|EXIT to return to the page display.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Map Menu, left; Map Orientation menu with
the North Up map orientation option selected, right.
NOTE:
In North Up and Course Up, the present position arrow appears in
the center of the map page. In Track Up, the position arrow appears
centered in the lower third of the page.
Navionics Charts
Your unit can display Navionics electronic charts on MMCs. They
work just like a MapCreate custom map on an MMC.
To display a Navionics chart:
1. Install the Navionics MMC in the memory card compartment and
turn on the unit. (For full card install instructions, see Sec. 2.)
WARNING:
You should never format the MMC containing your
Navionics chart. Formatting the MMC will permanently
erase the chart from the card.
2. From the Map Page, press MENU|↓ to MAP DATA|ENT|↓ to NAVIONICS
MAP CHOICE|ENT. Use ↑ or ↓ to select the Map Name, then press
ENT|EXIT|EXIT.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
These figures show menu sequence (from left to right) for selecting a
Navionics chart for the South Chesapeake Bay area.
3. To turn off a Navionics chart, From the Map Page, press MENU|↓ to
MAP DATA|ENT|↓ to NAVIONICS MAP CHOICE|ENT. Use ↑ or ↓ to select
LOWRANCE, then press ENT|EXIT|EXIT.
Port Information
Navionics charts contain Port Services information, represented by an-
chor icons on the map display. An example is displayed in the following
figure.
To view Port Services information:
1. Use the arrow keys to move the cursor over a Port Services icon.
When selected, a pop-up name box appears.
2. Press WPT to display the Port Services Information screen.
The Port Services information screen has two windows. The top window
lists the various service categories. The lower window lists the detailed
services available in each basic category.
Port Services
icons
Pop-up
name box
Cursor lines
Navionics chart showing Port Services icon selected by cursor.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
3. To scroll through the Service Categories window: press ENT then use
↑ or ↓ to see the types of services available. As you highlight a different
category, the list in the lower window changes. To return to the Map
Page, press EXIT|EXIT.
4. Depending on the location, the Detailed Services window may have a
long list of services under the General Services category. To scroll
through the Detailed Services window: from SERVICE CATEGORIES, press ↓
to DETAILED SERVICES|ENT, then use ↑ or ↓ to read the list of available
services. To return to the Map Page, press EXIT|EXIT. To return to the
top service category window, press ENT|↑.
Port Services information screens.
Tidal Current Information
Navionics charts contain Tidal Current information,
represented at large zoom ranges by a box icon with
the letter "C." The icon stands for a Tidal Current
Station location. An example is displayed at right.
When you zoom in to a sufficiently small zoom range, the icon itself be-
comes an animated arrow showing tidal current velocity and direction for
the selected tidal station at the present time. At larger zoom ranges, you
can select the boxed "C" icon and it becomes an animated arrow with a
pop-up name box. An example is displayed in the following figure.
To view Tidal Current information:
1. Use the arrow keys to move the cursor over a Tidal Current Station
icon. When selected, a pop-up name box appears.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Tidal Current
Station icon
in animated
mode
Pop-up
name box
Cursor lines
Navionics chart showing Tidal Current Station icon selected by cur-
sor. In this example, the current is flowing to the west at 0.2 kn.
2. Press WPT to display the Tidal Current Information screen.
Current Information screen.
The Tidal Current Information screen displays daily tidal current data
for this station on this date at the present time. The graph at the top of
the screen is an approximate view of the flood and ebb pattern for the
day, from midnight (MN), to noon (NN) to midnight (MN). The velocity
scale at the top left side of the graph changes dynamically based upon
the maximum velocity of the current for that day.
Slack water, the period of little or no current, is represented by the
Slack Water Line (SWL). The flood appears above the SWL and the ebb
appears below the SWL.
You can look up tidal current data for other dates by changing the
month, day and year selection boxes. To select another date:
89
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Use → and ← to highlight month, day or year, then press ENT.
2. Use ↑ and ↓ to select the desired month, day or year, then press ENT.
To clear the information screen, press EXIT.
Tide Information
Navionics
charts
contain
Tidal
Information,
represented at large zoom ranges by a box icon with
the letter "T." The icon stands for a Tidal Station
location. An example is displayed at right.
When you zoom in to a sufficiently small zoom range, the icon itself be-
comes an animated gauge showing a rising or falling tidal height for the
selected station at the present time. At larger zoom ranges, you can se-
lect the boxed "T" icon and it becomes an animated gauge with a pop-up
name box. An example is displayed in the following figure.
To view tide information:
1. Select a Tide Station icon: use the arrow keys to move the cursor over
an icon. When it is selected, a pop-up name box appears.
2. After selecting the Tide Station icon, press WPT to display the Tide
Information screen.
Cursor line
Pop-up
name box
Tide Station
icon
Navionics chart showing Tide Station icon selected by cursor.
In the example above, the tide is at 1.5 feet and rising,
as shown by the up arrow at the top of the icon.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Tide Information screen.
The Tide Information screen displays daily tidal data for this station on
this date at the present time. The graph at the top of the screen is an
approximate view of the tidal range pattern for the day, from midnight
(MN), to noon (NN) to midnight (MN). The dotted line across the graph
is the Mean Lower Low Water line (MLLW).
The height scale on the top right side of the graph changes, based upon
the maximum range of the tide for that day. The MLLW line also ad-
justs its position as the height scale changes.
You can look up tidal data for other dates by changing the month, day
and year selection boxes. To select another date:
1. Use → and ← to highlight month, day or year, then press ENT.
2. Use ↑ and ↓ to select the desired month, day or year, then press ENT.
To clear the information screen, press EXIT.
Pop-up Help
Help is available for virtually all of the menu labels on this unit. By
highlighting a menu item and leaving it highlighted for a few seconds, a
"pop-up" message appears that describes the function of the menu item.
This feature is on by default.
To set up Popup Help: Press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓
to POPUP HELP. With the option highlighted, press ENT to check it (turn
on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to
return to the page display.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup Menu, left, with Pop-up Help command highlighted. At
right, this example shows the Pop-up Help message for the Overlay
Data command, located on the Map Page menu.
Position Pinning
When you are standing still or moving at extremely slow speed, a GPS
receiver can have trouble determining the direction you are traveling.
In the past, this resulted in a "wandering" plot trail that moved around
the map, even if you were standing still.
The Position Pinning feature was developed so that when you stopped,
the unit locked the present position on the GPS plotter until you moved
a short distance or exceeded a very slow speed.
The command remains available in the unit's software, but we recom-
mend that you leave it in the default off (unchecked) mode. The "wan-
dering" plot trail issue has now been corrected by the Track Smoothing
feature. Turning on Position Pinning could actually result in an inaccu-
rate plot trail if you are moving around in a relatively small area. If you
want to experiment with Position Pinning, the same instructions are
used to turn the feature on (checked) and off (unchecked.)
1. Press MENU|MENU|↓ to GPS SETUP|ENT|↓ to POSITION PINNING|ENT.
2. Press EXIT|EXIT to return to the previous page.
Reset Options
To reset all features to their factory defaults:
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓ to RESET OPTIONS|ENT|←
to YES|ENT.
NOTE:
Reset Options does not erase any waypoints, routes, icons or plot trails.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
System Menu with Reset Options command selected.
Require WAAS
You can force the unit to require WAAS for reporting a valid position.
(The default setting, off, uses WAAS automatically, but doesn't require
it to yield a position.) Here's how to turn it on and off:
1. Press MENU|MENU|↓ to GPS SETUP|ENT|↓ to REQUIRE WAAS|ENT.
2. To return to the last page displayed, press EXIT|EXIT.
3. You can return to this command and press ENT again to turn the fea-
ture off.
Require WAAS command on the GPS Setup Menu.
Screen Contrast and Brightness
To access the Screen menu, press MENU|MENU|ENT.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Once in the Screen menu:
To adjust the display's contrast:
The CONTRAST slider bar is already selected. Press → or ← to move the
bar. The left end of the scale is minimum contrast; the right end is
maximum contrast.
Screen Command, left, and Screen Menu with Contrast bar selected, right.
To adjust the display's brightness:
Press ↓ to BRIGHTNESS. Press → or ← to move the bar. The left end of the
scale is minimum contrast; the right end is maximum contrast.
To adjust the screen's display mode:
Press ↓ to DISPLAY MODE|ENT|press ↑ or ↓ to select mode|EXIT.
Display Mode menu.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Language
This unit's menus are available in 10 languages: English, French, Ger-
man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish.
To select a different language:
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT.
2. Press ↓ to SET LANGUAGE…|ENT.
3. Use ↓ or ↑ to select a different language and press ENT. All menus
now appear in the language you selected.
Set Local Time
Using the correct local time setting is handy when estimating local ar-
rival time while navigating. Also, the time and date are saved when a
waypoint is created.
To access the Set Local Time menu, you must first acquire your posi-
tion. Once that is done: press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓ to
SET LOCAL TIME|ENT.
Once in the Time Settings menu:
To set Local Time: Press ENT. Press ↑ or ↓ to change the first charac-
ter, then press → to move the cursor to the next character. Repeat until
the time is correct, then press ENT.
To set the Month: Press ↓ to MONTH|ENT. Press ↑ or ↓ to select the
month, then press ENT.
To set the Day: Press ↓ to MONTH|→ to DAY|ENT. Press ↑ or ↓ to select
the day, then press ENT.
To set the Year: Press ↓ to MONTH|→ to YEAR|ENT. Press ↑ or ↓ to se-
lect the year, then press ENT.
The last field in this menu is CONFIG DST. This feature allows your unit
to automatically adjust with the time change caused by Daylight Sav-
ing Time (you should only have to set it once). You may select which set
of rules matches DST in your region, or simply accept the default.
Once you have each field set the way you want, press EXIT repeatedly
until you return to the previous page.
Show WAAS Alarm
When the signal is available, your unit will automatically use WAAS to
boost the accuracy of the position fix. When the WAAS signal is lost or
acquired, an alarm message appears. Since the U.S. government is still
developing the WAAS system, it's not unusual for a GPS/WAAS re-
ceiver to frequently lose and reacquire its lock on a WAAS satellite.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
That can result in the alarm repeatedly going on and off. If you want,
you have the option of turning off the WAAS Acquired/Lost alarm with-
out affecting how the unit uses WAAS. Here's how:
1. Press MENU|MENU|↓ to GPS SETUP|ENT|↓ to SHOW WAAS ALARM.
2. With the option highlighted, press ENT to uncheck it (turn off) and
check it (turn on.) After the option is set, press EXIT|EXIT to return to
the page display.
3. You can return to this command and press ENT again to turn the fea-
ture on.
Software Version Information
From time to time, Lowrance updates the operating system software in
some of its products. These software upgrades are usually offered to
customers as free downloads from our web site, www.lowrance.com.
These upgrades make the unit perform better or introduce a new fea-
ture or function. You can find out what software version is running in
your unit by using the Software Information command.
At left, Main Menu with Software Information command selected.
At right, the Software Information screen.
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓ to SOFTWARE INFORMA-
TION|ENT.
2. Read the information displayed on the screen.
3. To return to the last page displayed, press EXIT|EXIT|EXIT.
Sounds and Alarm Sound Styles
Sounds triggered by key strokes and alarms can be adjusted:
You first press MENU|MENU|↓ to SOUNDS|ENT.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Sounds command, left. At right, the Sounds menu.
Once in the Sounds menu:
To set Key Press Sounds: With the option highlighted, press ENT to
check it (turn on) and uncheck it (turn off.) After the option is set, press
EXIT|EXIT to return to the page display.
To set Alarm Sounds: Press ↓ to ALARM SOUNDS. With the option high-
lighted, press ENT to check it (turn on) and uncheck it (turn off.) After
the option is set, press EXIT|EXIT to return to the page display.
To set Alarm Volume: Press ↓ to VOLUME. Press → or ← to move the
bar. The left end of the scale is low volume; the right end is high volume.
After the option is set, press EXIT|EXIT to return to the page display.
To set Alarm Style: Press ↓ to ALARM STYLE|ENT. Press ↑ or ↓ to
change the style, then press ENT. After the option is set, press
EXIT|EXIT to return to the page display.
Track Smoothing
This is a factory setting on the GPS Setup menu that should always be
left on. When stopped or traveling at slow speeds (such as walking or
trolling), Track Smoothing prevents wandering of trails, the steering
arrow, compass rose and a map in track-up mode.
Track Smoothing option, turned on.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Trail Options
There are several options you can use with trails. Some affect all trails,
other options can be applied to a particular trail. You can change the
way trails are updated, display or hide trails, create a new trail, delete
a trail, etc.
General Trail Options
To access the Trails Menu:
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
Main Menu, left, Trails Menu, center, Trail Options, right.
Delete All Trails
To remove all of the trails from memory: from the Trails Menu, press →
to DELETE ALL|ENT|← to YES|ENT.
Update Trail Option
This menu lets you change the way the trail updates occur.
WARNING:
If you uncheck the Update Trail option, automatic trail
creation and recording will be turned off. You must turn
it back on to record trails. The default setting is on.
From the Trails Menu, press ↓ to OPTIONS|ENT. With UPDATE ACTIVE TRAIL
highlighted, press ENT to check it (turn on) and uncheck it (turn off).
Update Trail Criteria (Auto, Time, Distance)
The options are automatic, time, or distance. When it's in the default
automatic mode, the unit doesn't update the plot trail while you're
traveling in a straight line. Once you deviate from a straight line, the
98
Download from Www.Somanuals.com. All Manuals Search And Download.
unit "drops" a plot point (trail waypoint) onto the trail. This conserves
plot trail points. If a plot trail uses all of the available points allotted to
it, the beginning points are taken away and placed at the end of the trail.
From the Trails Menu, press ↓ to OPTIONS|ENT|↓ to UPDATE CRITERIA.
Press ← or → to select criteria type|ENT.
Trail Update Rate (Time, Distance)
You can update a trail by time, with a range from 1 second to 9999 sec-
onds; the default is 3 seconds. You can update by distance, with a range
from 0.01 mile/nm/km to 9.99 mile/nm/km; the default is 0.10 mi.
With one of the Update Criteria selected, use the cursor arrows to
highlight either the UPDATE RATE or UPDATE DISTANCE data entry boxes and
press ENT. Press ↑ or ↓ to change the first character, then press → to
the next character and repeat until the entry is correct. Press EXIT to
return to the Trail Options Menu.
Trail Options menu: Update Time Rate setting, left, and Update Dis-
tance setting, right.
Specific Trail Options
Delete Trail
To delete a specific trail: From the Trails Menu, press ↓ to Trail
Name|ENT. The Edit Trail menu appears as seen in the following fig-
ure. Press ↓ to DELETE TRAIL|ENT|← to YES|ENT.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit Trail menu.
New Trail
To manually start a new trail, in the Trails Menu, make sure NEW TRAIL
is highlighted and press ENT.
Trail Visible/Invisible and Other Trail Options
The name, maximum number of points in the trail, activity, and visi-
bility are all changed on the Edit Trail menu screen. The Active setting
determines whether or not the unit is recording new points for a par-
ticular trail.
On the Edit Trail menu, press ↓ or ↑ to highlight the section you wish
to change, then press ENT. Make your changes, then press EXIT to erase
this menu. Related trail functions are discussed in further detail under
the Trails topic in Sec. 4, Advanced GPS Operations.
Transparency
Use the transparency menu to adjust the transparency of menu win-
dows. A high transparency allows you to continue monitoring the
screen's display while adjusting feature settings, though the text of the
menus may fade until it is unreadable. A low transparency will usually
make menu text easier to read, at the cost of watching your display.
Experiment with this feature until you find the right level of transpar-
ency for your eyes.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu with Transparency command selected.
To adjust Menu Transparency level:
Press MENU|MENU|↓ to TRANSPARENCY|ENT. The TRANSPARENCY slider bar
appears. Press ↑ or ↓ to move the bar. The lower end of the scale makes
the menus opaque; the upper end is maximum transparency.
Units of Measure
This menu sets the speed and distance (statute or nautical miles, me-
ters), depth (feet, fathoms, or meters), temperature (degrees Fahrenheit
or Celsius) and heading (true or magnetic) units. To change the units:
Press MENU|MENU|↓ to SYSTEM SETUP|ENT|ENT.
Main Menu, System Setup submenu, left; Units of Measure Menu, right.
To set Unit of Measure: Use ↑ ↓ ← → to select the unit of measure in
the desired category. With the desired unit of measurement high-
lighted, press ENT. After the option is set, press EXIT|EXIT|EXIT to re-
turn to the page display.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Searching
NOTE:
The background map loaded in your unit lets you to search for U.S.
Interstate Highway exits and exit services, as well as some land
features, including cities and lakes. For a full set of searchable land
features, including landmarks, streets, addresses and Points of In-
terest, you must load your own high-detail custom map produced
with our MapCreate 6 software. For a complete description of what
detail is found in the background map and custom MapCreate
maps, see page 36. (Remember, our pre-made FreedomMaps con-
tain all the same detail found in custom-made MapCreate maps.)
This unit's varied search functions all begin with either the Find Way-
point menu or the Map Page menu. Press WPT and the Find Waypoint
menu appears for waypoints and Points of Interest (POI). From the
Map Page, press MENU and the Map Page menu appears for streets,
addresses and highway exits.
Find Waypoint menu, left; Map Page menu, right.
IMPORTANT NOTES:
Our search commands let you look up items by name, or search for
the item nearest to you. When you search, the unit looks for items
in the vicinity of your current position. If you are using the unit in-
doors, in simulator mode or otherwise haven't locked on to satel-
lites, the unit looks near the last known position.
To search in some other location, use the arrow keys to center the
map cursor where you want to look. When the cursor is active, the
unit always begins searching at the cursor location.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
In search results, the distance and bearing to the selected item will
be calculated from the current position. In the case of a cursor
search, the search results show distance and bearing from the cur-
sor, but an individual waypoint's information screen shows distance
and bearing from the current (or last known) position.
Find Addresses
1. From the Map Page, press MENU|↓ to FIND ADDRESS|ENT.
2. Press ENT to search in the Address field.
3. To enter an address number, press ↑ or ↓ to change the first
number, then press → to move the cursor to the next number and re-
peat until the number is correct, then press ENT.
Find Address Menu.
4. To enter a street name, press ↓ to STREET|ENT. There are two op-
tions: A. You can spell out the name in the top selection box. Press ↑
or ↓ to change the first letter, then press → to move the cursor to the
next letter and repeat until the name is correct, then press ENT|ENT. B.
Jump down to the lower selection list by pressing ENT, then press ↓ or ↑
to select a street name from the list, then press ENT. The street name
you selected is now in the street field.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Address menu, left; Find Street menu, center,
with Find By Name field active; street name entry complete, right.
5. To enter a city name, press ↓ to CITY|ENT. You will be asked if you
want to find addresses only within a particular city. This option is de-
signed so you can limit an address search to a single city if necessary
(see the following note).
If you select yes, there are two options: A. You can spell out the city
name in the top selection box. Press ↑ or ↓ to change the first letter, then
press → to move the cursor to the next letter and repeat until the name
is correct, then press ENT|ENT. B. Jump down to the lower selection list
by pressing ENT, then press ↓ or ↑ to select a city name from the list,
then press ENT. The city name you selected is now in the city field.
NOTE:
We recommend that you do not enter a city name unless the list you
are given is too large when searching without it. This unit can ac-
tually search quicker without a city and you save time by not en-
tering a city name.
Find City field, left, Search in particular city only option, center; Find
City by name, right.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
6. When the necessary search fields are filled in, press ↓ to FIND AD-
DRESS|ENT. Your unit asks you to wait while it searches for the address.
(If an address is not in the database, a message appears saying the ad-
dress could not be found.)
7. The unit will display a list of addresses. If the address you are look-
ing for is highlighted at the top of the list, press ENT. If not, use ↓ and ↑
to select the correct address from the list, then press ENT. The Map
Page will then appear with the location selected by the cursor. (In the
following example, we are looking for 12303 East 11th Street in Tulsa,
not 11th Court, so we had to scroll down the list to select the right one.)
Address search result list, left. At center, Map Page showing location
of the address on the map, highlighted by cursor. At right, after the
address is located, you can navigate to it ("D" symbol for destination).
8. To navigate to the address, press MENU|ENT|EXIT and the unit will
begin showing navigation information to the address pointed out by the
cursor. If you are only looking up an address (not navigating), just
press EXIT to return to the previous page.
Tip:
If the address also happens to be an item in the Point of Interest
database, you can look up the item's phone number in the Waypoint
Information list. With the address location selected by the cursor on
the map, press WPT. The POI's Waypoint Information window ap-
pears, with the Go To Waypoint command highlighted. If you want
to go ahead and navigate to the POI address, just press ENT|EXIT.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Left, Map Page showing location of the address on the map, high-
lighted by cursor. Center, this address is a business in the POI data-
base, so you can display the POI information window, then navigate to
it. At right, this address is not in the POI database, so the Waypoint
key will not display any information for this address.
Find Any Item Selected by Map Cursor
On the Map Page: with a POI or map feature selected by the cursor
press WPT. To return to the previous page, press EXIT.
A POI selected by the cursor, left, POI information screen, right.
NOTE:
Since the Go To waypoint command is highlighted, you can navi-
gate to the selected POI by pressing ENT|EXIT while in the POI
Waypoint Information screen.
Find Interstate Highway Exits
1. From the Map Page, press MENU|↓ to HIGHWAY EXITS|ENT, which calls
up the Find Exit menu.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Highway Exits command, left, and Find Exit menu, right.
2. First, select a highway name by pressing ENT, which calls up the
Find By Name menu. There are two highway search options: A. You
can spell out the highway name in the top selection box. Press ↑ or ↓
to change the first letter, then press → to move the cursor to the next
letter and repeat until the name is correct, then press ENT|ENT. B.
Jump down to the lower selection list by pressing ENT, then press ↓ or ↑
to select a highway from the list, then press ENT.
Find By Name menu.
3. Once you have selected a highway name you can then select an exit.
Press ↓ to switch to the Exit List, then press ↓ or ↑ until you highlight
the exit, then press ENT.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Exit menu, with an exit selected in the Exit List.
4. In the Exit Information screen you have two choices. A. Press ENT to
navigate or "go to" the exit. B. Press →|ENT to find the exit on the map.
"Go To Exit" option, left, "Find On Map" option, right.
Tip:
You can also look up some additional information on the Exit Serv-
ices located near this exit. Press ↓ to SERVICES|press ↓ or ↑ to select
Service Name|ENT.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Exit Information screen, left; general location
and amenities information, at right.
Find Map Places or Points of Interest (POI)
1. Press WPT, press ↓ or ↑ to select a map place or POI category, then
press ENT. (To narrow your search, press → or ← to select a subcate-
gory before pressing ENT.) You will be given two options; Search By
Name or By Nearest.
Find Waypoint menu with Lodging POI category selected, left, and
with the RV Parks subcategory selected, right.
2. Search by nearest POI. Press ↓|ENT. The "find by nearest" menu
will show a "calculating" screen, then a list of the nearest POI's will
appear. Press ↓ or ↑ to the selected POI and press ENT to call up the
POI's Waypoint Information screen.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Find by Nearest option, left, Calculating screen, center, POI list, right.
3. Search by name of POI. Press ENT. There are two options: A. You
can spell out the POI in the top selection box. Press ↑ or ↓ to change
the first letter, then press → to move the cursor to the next letter and
repeat until the name is correct, then press ENT|ENT. B. Jump down to
the lower selection list by pressing ENT, then press ↓ or ↑ to select a
POI from the list, then press ENT to call up the POI's Waypoint Infor-
mation screen.
Find by Name option, left, Find by Name menu, right.
4. When the POI's Waypoint Information screen is displayed, you can
choose to "Go To" the POI waypoint by pressing ENT or find it on the
map by pressing→|ENT.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
"Go To" POI option, left, "Find on Map" POI option, right.
Find Streets or Intersections
Find a Street
1. From the Map Page, press MENU|↓ to FIND STREETS|ENT and the Find
Streets Menu appears.
Find Streets command, left, Find Streets menu, right.
2. You must first fill in a street name in the First Street dialog box.
Press ENT to display the Find By Name menu. There are two options:
A. You can spell out the street in the top selection box. Press ↑ or ↓ to
change the first letter, then press → to move the cursor to the next let-
ter and repeat until the name is correct, then press ENT|ENT. B. Or you
can jump down to the lower box and pick a street from the selection
list. Press ENT, then press ↓ or ↑ to select a street from the list and
press ENT.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Street By Name menu. Spell out name in
the top box, or select from the list in the lower box.
3. The Find Streets menu reappears with the street you're searching for
in the First Street box. (In this example, it's I-35.) To search for that
street, press ↓ to FIND FIRST STREET|ENT. A message appears asking you to
wait while the unit finds the street. When the Streets Found list appears,
press ↑ or ↓ to select the street you are searching for and press ENT.
At left, the Find Streets menu with the Find First
Street command highlighted. At right, Streets Found list.
4. The Map Page appears, with the cursor pointing to the found street.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Map Page showing results of a street search.
The cursor points to the located street.
If you want to navigate to the found street at the cursor location, just
press MENU|ENT|EXIT.
Find an Intersection
You must enter one street in the First Street dialog box and enter the
next street in the Second Street dialog box.
1. From the Map Page, press MENU|↓ to FIND STREETS|ENT and the Find
Streets Menu appears.
2. You must fill in a street name in the First Street dialog box. Press ENT
to display the Find By Name menu. There are two options: A. You can
spell out the street in the top selection box. Press ↑ or ↓ to change the
first letter, then press → to move the cursor to the next letter and repeat
until the name is correct, then press ENT|ENT. B. Or you can jump down
to the lower box and pick a street from the selection list. Press ENT,
then press ↓ or ↑ to select a street from the list and press ENT.
3. The Find Streets menu reappears with the street you're searching for
in the First Street box. (In this example, it's I-35.)
4. Now fill in the second street. Press ↓ to SECOND STREET|ENT and the
Find By Name menu appears again. Just like before, there are two op-
tions: A. You can spell out the second street in the top selection box.
Press ↑ or ↓ to change the first letter, then press → to move the cursor
to the next letter and repeat until the name is correct, then press
ENT|ENT. B. Or you can jump down to the lower box and pick the sec-
ond street from the selection list. Press ENT, then press ↓ or ↑ to se-
lect a street from the list and press ENT.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The Find Streets menu reappears with the first and second street
dialog boxes filled in. In this example, we selected I-44 as our second
street. You could now use similar techniques to select a city or Zip code,
but your search will probably be faster if you leave those boxes blank.
(You can specify a city and/or Zip code later on to narrow the search, if
the resulting list is too long.)
Find Intersection command highlighted, left.
Intersections Found list, right.
6. To search for the intersection of the two streets, press ↓ to FIND
INTERSECTION|ENT. A message appears asking you to wait while the unit
finds the intersection. When the Intersections Found list appears, press
↑ or ↓ to select the intersection you are searching for and press ENT. (In
the previous example, we selected the intersection of I-35 and I-44.)
7. The Map Page appears, with the cursor pointing to the found inter-
section. The intersection in our example is shown below.
Map Page showing results of an intersection search.
The cursor points to the located intersection.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
If you want to navigate to the found intersection, just press
MENU|ENT|EXIT.
Find Waypoints
1. Press WPT|↑ to MY WAYPOINTS|ENT.
2. If searching for the waypoint By Name, press ENT. If searching for
the Nearest waypoint, press ↓ to NEAREST|ENT. (To search by name,
jump to step 5.)
Find Waypoint menu, left; Find By Nearest command, center,
Find by Name command, right.
3. If you're looking for nearest, the unit says it is calculating, then a
list of waypoints appears. The closest is highlighted at the top of the
list and the farthest at the bottom of the list.
Calculating message, left, and list of the nearest waypoints, right.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
4. To see location information on the closest (highlighted) waypoint,
press ENT and the Waypoint Information screen appears. (If you
wanted to, you could select another waypoint from the list with the ↑ or
↓ keys.)
A. To navigate to the waypoint, press ENT. (The Go To Waypoint
command is already highlighted.) The unit will show navigation in-
formation to the waypoint.
B. To find the waypoint, press → to FIND ON MAP|ENT. The Map
Page appears with the cursor highlighting the found waypoint.
Waypoint Information screens with the Go To Waypoint command se-
lected, left, and the Find on Map command selected, right.
To clear these menus and return to the previous page, press EXIT re-
peatedly.
5. If you're looking by name, there are two options: A. You can spell
out the name in the top selection box. Press ↑ or ↓ to change the first
letter, then press → to move the cursor to the next letter and repeat
until the name is correct, then press ENT|ENT. B. Or you can jump
down to the lower selection list by pressing ENT, then press ↓ or ↑ to
select a waypoint from the list, then press ENT. The waypoint informa-
tion screen appears.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Find By Name menu, left. Waypoint Information screen, center. At right,
the found waypoint is highlighted by the cursor on the Map Page.
A. To navigate to the waypoint, press ENT. (Go To Waypoint com-
mand is already highlighted.) The unit will show navigation infor-
mation to the waypoint.
B. To find the waypoint, press → to FIND ON MAP|ENT. The Map
Page appears with the cursor highlighting the found waypoint.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Supplemental Material
Datums Used by This Unit
WGS 1984
Default
Zaire, Zambia and
Zimbabwe
Australian Geodetic
1984 - Australia &
Tasmania
Adindan
Mean for Ethiopia,
Sudan
Arc 1950 - Botswana
Arc 1950 - Burundi
Arc 1950 - Lesotho
Arc 1950 - Malawi
Arc 1950 - Swaziland
Arc 1950 - Zaire
Ayabelle Lighthouse -
Djibouti
Adindan
Burkina Faso
Bellevue (IGN) -
Efate & Erromango
Islands
Adindan
Cameroon
Bermuda 1957 -
Bermuda
Adindan
Ethiopia
Bissau - Guinea-
Bissau
Bogota Observatory -
Colombia
Arc 1950 - Zambia
Arc 1950 - Zimbabwe
Adindan
Mali
Adindan
Senegal
Arc 1960 - Mean for
Kenya, Tanzania
Bukit Rimpah - Indo-
nesia (Bangka & Be-
litung Islands)
Adindan
Sudan
Ascension Island
1958 - Ascension
Island
Camp Area Astro -
Antarctica (McMurdo
Camp Area)
Afgooye
Somalia
Astro Beacon E 1945
- Iwo Jima
Campo Inchauspe -
Argentina
Ain el Abd 1970
Bahrain
Astro DOS 71/4 - St.
Helena Island
Canton Astro 1966 -
Phoenix Islands
Ain el Abd 1970
Saudi Arabia
Astro Tern Island
(FRIG) 1961 - Tern
Island
Cape - South Africa
Anna 1 Astro 1965
Cocos Islands
Cape Canaveral -
Bahamas, Florida
Astronomical Station
1952 - Marcus Island
Antigua Island Astro
1943; Antigua (Lee-
ward Islands)
Carthage - Tunisia
Switzerland
Australian Geodetic
1966 - Australia &
Tasmania
Arc 1950; Mean for
Botswana, Lesotho,
Malawi, Swaziland,
Chatham Island Astro
1971; New Zealand
(Chatham Island)
119
Download from Www.Somanuals.com. All Manuals Search And Download.
European 1950
England, Channel
Islands, Ireland,
Scotland, Shetland
Islands
L.C. 5 Astro 1961
Cayman Brac Island
Chua Astro
Paraguay
Leigon
Ghana
Corrego Alegre
Brazil
European 1950
Finland, Norway
Liberia 1964
Liberia
Dabola
Guinea
European 1950
Greece
Luzon
Philippines (Exclud-
ing Mindanao)
Djakarta (Batavia)
Indonesia (Sumatra)
European 1950
Iran
DOS 1968
Luzon
New Georgia Islands
(Gizo Island)
Philippines (Min-
danao)
European 1950
Italy (Sardinia)
Easter Island 1967
Easter Island
Mahe 1971
Mahe Island
European 1950
(Sicily)
European 1950
European 1950
Malta
Massawa
Ethiopia (Eritrea)
Mean for Austria,
Belgium, Denmark,
Finland, France,
West Germany, Gi-
braltar, Greece, Italy,
Luxembourg, Neth-
erlands, Norway,
Portugal, Spain,
Ireland 1965
Ireland
Merchich
Morocco
ISTS 061 Astro 1968
South Georgia Is-
lands
Midway Astro 1961
Midway Islands
Sweden, Switzerland
Minna
ISTS 073 Astro 1969
Diego Garcia
Cameroon
European 1950
Mean for Austria,
Denmark, France,
West Germany,
Netherlands, Swit-
zerland
Minna
Nigeria
Johnston Island 1961
Johnston Island
Montserrat Island
Astro 1958; Montser-
rat (Leeward Islands)
Kandawala
Sri Lanka
European 1950
Mean for Iraq, Israel,
Jordan, Lebanon,
Kuwait, Saudi Arabia,
Syria
Kerguelen Island
1949
Kerguelen Island
M’Poraloko
Gabon, Nahrwan,
Oman (Masirah Is-
land)
Kertau 1948
West Malaysia &
Singapore
European 1950
Cyprus
Nahrwan
Saudi Arabia
European 1950
Egypt
Kusaie Astro 1951
Caroline Islands
Nahrwan
United Arab Emirates
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Naparima BWI
Trinidad & Tobago
North American 1927
Canada (Alberta,
British Columbia)
Old Hawaiian
Mean for Hawaii,
Kauai, Maui, Oahu
North American 1927
Mean for Antigua,
Barbados, Barbuda,
Caicos Islands,
North American 1927
Canada (Manitoba,
Ontario)
Old Hawaiian
Hawaii
Cuba, Dominican
Republic, Grand
Cayman, Jamaica,
Turks Islands
Old Hawaiian
Kauai
North American 1927
Canada (New
Brunswick, New-
foundland, Nova
Scotia, Quebec)
Old Hawaiian
Maui
North American 1927
Mean for Belize,
Costa Rica, El Sal-
vador, Guatemala,
Honduras, Nicaragua
Old Hawaiian
Oahu
North American 1927
Canada (Northwest
Territories, Sas-
katchewan)
Oman
Oman
North American 1927
Mean for Canada
North American 1927
Canada (Yukon)
Ordinance Survey
Great Britain 1936 -
Mean for England,
Isle of Man, Scotland,
Shetland Islands,
Wales
North American 1927
Mean for CONUS
(Continental United
States)
North American 1927
Canal Zone
North American 1927
Mean for CONUS
(East of Mississippi
River) including Lou-
isiana, Missouri, Min-
nesota
North American 1927
Cuba
Ordinance Survey
Great Britain 1936 -
England
North American 1927
Greenland (Hayes
Peninsula)
Ordinance Survey
Great Britain 1936 -
England, Isle of Man,
Wales
North American 1927
Mean for CONUS
(West of Mississippi
River)
North American 1927
Mexico
North American 1983
Alaska, Canada,
CONUS
Ordinance Survey
Great Britain 1936 -
Scotland, Shetland
Islands
North American 1927
Alaska
North American 1983
Central America,
Mexico
North American 1927
Bahamas (Except
San Salvador Island)
Ordinance Survey
Great Britain 1936 -
Wales
Observaorio Metereo
1939; Azores (Corvo
& Flores Islands)
North American 1927
Bahamas (San Sal-
vador Island)
Pico de las Nieves
Canary Islands
Old Egyptian 1907
Egypt
Pitcairn Astro 1967
Pitcairn Island
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Point 58
Sweden
Tokyo
Mean for Japan, Ko-
rea, Okinawa
South American 1969
Chile
Santo (DOS)
1965 Espirito Santo
Island
South American 1969
Colombia
Tokyo
Japan
South American 1969
Ecuador
Tokyo
Korea
Sao Braz
Azores (Sao Miguel,
Santa Maria Islands)
South American 1969
Ecuador (Baltra, Ga-
lapagos)
Tokyo
Sapper Hill 1943
Okinawa
East Falkland Island
South American 1969
Guyana
Tristan Astro 1968
Tristan da Cunha
Schwarzeck
Nambia
South American 1969
Paraguay
South American 1969
Peru
Viti Levu 1916
Fiji (Viti Levu Island)
Selvagem Grande
Salvage Islands
Wake
SGS 85
Soviet Geodetic
System 1985
South American 1969
Trinidad & Tobago
Eniwetok 1960
Marshall Islands
South American 1969
Mean for Argentina,
Bolivia, Brazil, Chile,
Colombia, Ecuador,
Guyana, Paraguay,
Peru, Trinidad & To-
bago, and Venezuela
South American 1969
Venezuela
Wake Island Astro
1952
Wake Atoll
South Asia
Singapore
WGS 1972
Global Definition
Tananarive Obser-
vatory 1925; Mada-
gascar
South American 1969
Argentina
Yacare
Uruguay
South American 1969
Bolivia
Timbalai 1948
Brunei, East Malay-
sia (Sabah, Sarawak)
Zanderij
Suriname
South American 1969
Brazil
122
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Compliance
This device complies with Part 15 of the U.S. Federal Communi-
cations Commission (FCC) Rules. Operation is subject to the fol-
lowing two conditions: (1) this device may not cause harmful in-
terference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired opera-
tion.
Changes or modifications not expressly approved by the manu-
facturer could void the user's authority to operate the equip-
ment.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•
Consult the factory customer service department for help.
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
G
Accessories, 1, 3, 4, 5, 6, 11, 21, 22, 26,
37, 56, 103
GPS Data File, 5, 56, 57, 58, 62, 74
Sec. 2, Installation & Accessories, 11
Alarm Clock, 70
Alarms, 29, 40, 54, 55, 56, 68, 73, 74, 80
Anchor Alarm, 73, 74
Antenna, 1, 3, 4, 11, 12, 13, 15, 19, 22,
23, 40, 41, 123
Arrival Alarm, 40, 54, 55, 56, 68, 73, 74,
80
I
Icons, 3, 5, 9, 28, 36, 37, 56, 60, 61, 84,
87, 88, 89, 90, 92
Creating, 60
Deleting, 61
Navigate, 61
Information Displays (Customize
Display), 31
Installation, 4, 6, 11, 12, 21, 22, 24, 56,
86
B
Backlights / Lighting, 2, 27
Batteries, 11, 17, 18
Sec. 2, Installation & Accessories, 11
Introduction
Brightness, 29, 93, 94
GPS and WAAS, 6
Sec. 1, Introduction, 1
Specifications, 2
Typographical Conventions, 9
C
Cancel Navigation, 29, 40, 49, 50, 54,
56, 58, 67
Communications Ports, 3, 11, 14, 15, 16,
17, 18, 19, 20, 74, 75
K
Keypad Description, 9, 27
Compass, 7, 32, 33, 34, 40, 44, 48, 49,
55, 61, 68, 80, 97
Contrast, 29, 93, 94
L
Languages, 3, 95
Lat/Lon Grid (Map Data option), 83
Coordinate System, 76
Cursor, 9, 28, 29, 37, 38, 40, 41, 42, 44,
45, 46, 47, 49, 50, 59, 60, 61, 62, 63,
64, 65, 66, 69, 71, 72, 80, 81, 83, 87,
88, 89, 90, 95, 99, 103, 104, 105, 106,
107, 108, 111, 112, 113, 114, 115,
117, 118
Undo Feature, 42
Custom Maps, 1, 3, 5, 6, 24, 26, 35, 36,
43, 45, 56, 62, 86, 103
M
Main Menu, 28, 29, 63, 67, 74, 96, 98,
101
Man Overboard, 48, 49
Map Boundaries (Map Data option), 82
Map Data, 82, 83, 86, 87
Map Datum, 77, 83, 84
Customize Display, 31
Customize Map Data Shown, 82, 83, 86,
87
Selection, 77, 83
Map Detail, 37, 82, 84
Map Fix (Coordinate System), 77, 78, 79
Map Menu, 82, 84, 86
Map Orientation, 34, 85, 86
Map Overlays (Map Data option), 82, 83
Memory Cards (MMC), 1, 3, 5, 6, 24,
25, 26, 27, 30, 35, 36, 40, 45, 52, 56,
D
Data Boxes (Customize Display), 31
Depth Range, 3, 4, 34, 35, 36, 37, 40,
41, 53, 81, 82, 83, 88, 90, 91, 99
125
Download from Www.Somanuals.com. All Manuals Search And Download.
57, 58, 62, 74, 86
Reset Options, 39, 45, 92, 93
Route, 3, 5, 7, 9, 10, 11, 13, 29, 32, 40,
54, 56, 62, 63, 64, 65, 66, 67, 68, 74,
80, 81, 92
Create and Save, 62
Delete, 65
N
Navigating, 10, 40, 47, 48, 49, 50, 53,
54, 55, 56, 61, 66, 67, 74
A Route, 66, 67
Navigate, 66, 67
A Trail, 53
Cancel, 29, 40, 49, 50, 54, 56, 58, 67
To Cursor Position, 49
To Icon, 61
Nearest, 42, 43, 44, 47, 103, 110, 111,
116
S
Searching, 2, 8, 41, 42, 43, 44, 46, 47,
48, 50, 59, 103, 104, 105, 106, 107,
108, 109, 110, 111, 112, 113, 114,
115, 116, 117, 118
NMEA, 3, 11, 14, 15, 16, 17, 18, 19, 20,
74, 75
Addresses, 104
By Cursor, 107
Highway Exits, 107
POIs, 110
Streets, 112, 113, 114, 115
Waypoints, 116
O
Off Course Alarm, 73
Overlay Data, 92
Set Local Time, 95
P
Simulator, 9, 79, 80, 81, 103
Software Version Information, 96
Sounds, 96
Page Displays, 2, 30, 38, 40, 79
Digital Data, 38
Sun/Moon Rise & Set Calculator, 70
Map, 9, 10, 27, 28, 30, 33, 34, 35, 36,
37, 38, 39, 40, 47, 48, 49, 53, 54, 59,
61, 62, 63, 65, 66, 67, 68, 79, 80, 81,
82, 83, 84, 85, 86, 87, 88, 92, 103,
104, 106, 107, 112, 113, 114, 115,
117, 118
Navigation, 27, 30, 32, 33, 34, 40, 47,
48, 49, 50, 53, 55, 61, 62, 65, 66, 67,
68, 79
Satellite Status, 27, 30, 31, 32, 40, 79
POI (Point of Interest), 28, 29, 36, 37,
43, 44, 45, 49, 50, 72, 79, 103, 106,
107, 110, 111, 112
POIs
Search, 110
Pop-up Help, 91, 92
Pop-up Map Info (Map Data option), 82
Power, 1, 2, 6, 11, 16, 17, 18, 19, 20, 21,
22, 23, 27, 28, 40
T
Text Boxes (Customize Display), 31
Track Smoothing, 92, 97
Trail, 3, 5, 9, 10, 24, 29, 32, 33, 34, 35,
40, 47, 50, 51, 52, 53, 54, 55, 56, 68,
69, 70, 80, 81, 84, 92, 97, 98, 99, 100
Delete, 68
Delete All, 98
Edit Name, 69
Navigate, 53
New Trail, 52, 100
Update Criteria, 98
Update Rate, 99
Transducer, 22, 23, 76
Transfer
Custom Maps, 56
GPS Data Files, 56
Product Specifications, 2
Trip Calculator, 30, 70
Trip Down Timer, 70
Trip Up Timer, 70
R
Range, 3, 4, 34, 35, 36, 37, 40, 41, 53,
81, 82, 83, 88, 90, 91, 99
Range Rings (Map Data option), 83
U
Units of Measure, 101
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities, 27, 30, 70
106, 107, 110, 111, 116, 117, 118
Delete, 70
Edit, 71
Search, 116
Select, 72
W
WAAS, 3, 4, 6, 7, 11, 31, 93, 95, 96
Require WAAS, 93
Waypoints, 2, 3, 5, 8, 9, 24, 28, 29, 32,
33, 34, 40, 42, 43, 44, 45, 46, 47, 48,
49, 50, 55, 56, 60, 62, 63, 64, 65, 66,
67, 68, 70, 71, 72, 73, 74, 77, 78, 79,
80, 81, 84, 85, 92, 95, 99, 103, 104,
Z
Zooming, 3, 28, 34, 35, 40, 41, 53, 63,
81
Auto Zoom, 81
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
128
Download from Www.Somanuals.com. All Manuals Search And Download.
LOWRANCE DATABASES LICENSE AGREEMENT
THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST
PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL,
FAMILY, OR HOUSEHOLD USE ("YOU") AND LOWRANCE ELECTRONICS,
INC., THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US").
USING THE PRODUCT ACCOMPANIED BY THIS LICENSE AGREEMENT
CONSTITUTES ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF
YOU DO NOT ACCEPT ALL TERMS AND CONDITIONS, PROMPTLY RE-
TURN THE PRODUCT WITHIN 30 DAYS OF PURCHASE. PLEASE RE-
TURN USING THE ENCLOSED UPS SHIPPING LABEL AND INCLUDE:
PROOF OF PURCHASE, NAME, ADDRESS, AND PHONE NUMBER. YOUR
PURCHASE PRICE AND ANY APPLICABLE TAXES WILL BE REFUNDED.
PLEASE ALLOW 4-6 WEEKS TO PROCESS YOUR REFUND.
1. This License Agreement applies to the one or more databases that
your product may contain. We refer to these singly as a "Database"
and together as the "Databases." Your product may thus include the
"WBS Database" which contains worldwide background surface
mapping data, the "SmartMap Database" which contains inland
mapping data, or other Databases.
2. The Databases that your product may contain are licensed, not sold.
We grant to you the nonexclusive, nonassignable right to use these
Databases for supplemental navigation reference purposes, but only
as long as you comply with the terms and conditions of this License
Agreement. We reserve the right to terminate this license if you
violate any aspect of this License Agreement. You are responsible for
using official government charts and prudent navigation for safe
travel.
3. The Databases housed in your product are protected by the copy-
right notices appearing on the product or its screen(s). You may
NOT modify, adapt, translate, reverse engineer, decompile, disas-
semble, rent, lease, or resell any Database, and you may NOT create
derivative works based upon any Database or its contents. Any un-
authorized reproduction, use, or transfer of a Database may be a
crime and may subject you to damages and attorney fees.
4. This License Agreement will terminate immediately without prior
notice from us if you fail to comply with or violate any of the provi-
sions of this Agreement. Upon termination, you will promptly return
all products containing one or more Databases to us.
5. Prices and programs are subject to change without notice.
6. This License Agreement shall be governed by the laws of the State of
Oklahoma and comprises the complete and exclusive understanding
between you and us concerning the above subject matter.
129
Download from Www.Somanuals.com. All Manuals Search And Download.
DATABASES LIMITED WARRANTY
"We", "our", or "us" refers to Lowrance Electronics, Inc., the manufacturer of
this product. "You" or "your" refers to the first person who purchases the prod-
uct as a consumer item for personal, family, or household use. The Databases
Limited Warranty applies to the one or more databases that your product may
contain. We refer to each of these as a "Database" or together as the "Data-
bases." Your product may thus include the "WBS Database" which contains
worldwide background surface mapping data, the "SmartMap Database" which
contains inland mapping data, or other Databases.
We warrant to you that we have accurately compiled, processed, and repro-
duced the portions of the source material on which the Databases are based.
However, we are under no obligation to provide updates to the Databases, and
the data contained in the Databases may be incomplete when compared to the
source material. WE MAKE NO EXPRESS OR IMPLIED WARRANTY OF
ANY KIND ABOUT THE ACCURACY OF THE SOURCE MATERIAL ITSELF,
INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If there is a defect in any Database, your exclusive remedy shall be, at our op-
tion, either a refund of the price you paid for the product containing the defec-
tive Database or a replacement of such product. WE WILL NOT UNDER ANY
CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSE-
QUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF ANY KIND.
Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages, so the above limitations or exclusions may not apply to you.
This warranty does NOT apply in the following circumstances: (1) when the
product has been serviced or repaired by anyone other than us; (2) when the
product has been connected, installed, combined, altered, adjusted, or handled
in a manner other than according to the instructions furnished with the prod-
uct; (3) when any serial number has been effaced, altered, or removed; or (4)
when any defect, problem, loss, or damage has resulted from any accident, mis-
use, negligence, or carelessness, or from any failure to provide reasonable and
necessary maintenance in accordance with the instructions of the owner’s man-
ual for the product.
We reserve the right to make changes or improvements in our products from
time to time without incurring the obligation to install such improvements or
changes on equipment or items previously manufactured.
This warranty gives you specific legal rights and you may also have other rights
which may vary from state to state.
Your remedies under this warranty will be available so long as you can show in
a reasonable manner that the defect occurred within one (1) year from the date
of your original purchase, and we must receive your warranty claim no later
than 30 days after such 1-year period expires. Your claim must be substanti-
ated by a dated sales receipt or sales slip.
130
Download from Www.Somanuals.com. All Manuals Search And Download.
LOWRANCE ELECTRONICS
FULL ONE-YEAR WARRANTY
"We," "our," or "us" refers to LOWRANCE ELECTRONICS, INC., the manufacturer of
this product. "You" or "your" refers to the first person who purchases this product as a
consumer item for personal, family or household use.
We warrant this product against defects or malfunctions in materials and workmanship,
and against failure to conform to this product's written specifications, all for one (1) year
from the date of original purchase by you. WE MAKE NO OTHER EXPRESS WAR-
RANTY OR REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING THIS
PRODUCT. Your remedies under this warranty will be available so long as you can show
in a reasonable manner that any defect or malfunction in materials or workmanship, or
any non-conformity with the product's written specifications, occurred within one year
from the date of your original purchase, which must be substantiated by a dated sales
receipt or sales slip. Any such defect, malfunction, or non-conformity which occurs within
one year from your original purchase date will either be repaired without charge or be
replaced with a new product identical or reasonably equivalent to this product, at our
option, within a reasonable time after our receipt of the product. If such defect, malfunc-
tion, or non-conformity remains after a reasonable number of attempts to repair by us,
you may elect to obtain without charge a replacement of the product or a refund for the
product. THIS REPAIR, OR REPLACEMENT OR REFUND (AS JUST DESCRIBED) IS
THE EXCLUSIVE REMEDY AVAILABLE TO YOU AGAINST US FOR ANY DEFECT,
MALFUNCTION, OR NON-CONFORMITY CONCERNING THE PRODUCT OR FOR
ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER CAUSE WHATSOEVER.
WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY
SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF
ANY KIND.
Some states do not allow the exclusion or limitation of incidental or consequential dam-
ages, so the above limitations or exclusions may not apply to you.
This warranty does NOT apply in the following circumstances: (1) when the product has
been serviced or repaired by anyone other than us; (2) when the product has been con-
nected, installed, combined, altered, adjusted, or handled in a manner other than ac-
cording to the instructions furnished with the product; (3) when any serial number has
been effaced, altered, or removed; or (4) when any defect, problem, loss, or damage has
resulted from any accident, misuse, negligence, or carelessness, or from any failure to
provide reasonable and necessary maintenance in accordance with the instructions of the
owner's manual for the product.
We reserve the right to make changes or improvements in our products from time to time
without incurring the obligation to install such improvements or changes on equipment
or items previously manufactured.
This warranty gives you specific legal rights and you may also have other rights which
may vary from state to state.
REMINDER: You must retain the sales slip or sales receipt proving the date of your
original purchase in case warranty service is ever required.
LOWRANCE ELECTRONICS
12000 E. SKELLY DRIVE, TULSA, OK 74128
(800) 324-1356
131
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Obtain Service…
…in the USA:
We back your investment in quality products with quick, expert service
and genuine Lowrance parts. If you're in the United States and you
have technical, return or repair questions, please contact the Factory
Customer Service Department. Before any product can be returned, you
must call customer service to determine if a return is necessary. Many
times, customer service can resolve your problem over the phone with-
out sending your product to the factory. To call us, use the following
toll-free number:
800-324-1356
8 a.m. to 5 p.m. Central Standard Time, M-F
Lowrance Electronics may find it necessary to change or end our ship-
ping policies, regulations, and special offers at any time. We reserve the
right to do so without notice.
…in Canada:
If you're in Canada and you have technical, return or repair questions,
please contact the Factory Customer Service Department. Before any
product can be returned, you must call customer service to determine if
a return is necessary. Many times, customer service can resolve your
problem over the phone without sending your product to the factory. To
call us, use the following toll-free number:
800-661-3983
905-629-1614 (not toll-free)
8 a.m. to 5 p.m. Eastern Standard Time, M-F
…outside Canada and the USA:
If you have technical, return or repair questions, contact the dealer in
the country where you purchased your unit. To locate a dealer near
you, visit our web site, www.lowrance.com and look for the Dealer Lo-
cator.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessory Ordering Information
for all countries
To order Lowrance accessories such as power or adapter cables, please
contact:
1) Your local marine dealer or consumer electronics store. Most quality
dealers that handle marine electronic equipment or other consumer
electronics should be able to assist you with these items.
To locate
a
Lowrance dealer near you, visit our web site,
www.lowrance.com and look for the Dealer Locator. Or, you can consult
your telephone directory for listings.
2) U.S. customers: LEI Extras Inc., PO Box 129, Catoosa, OK 74015-0129
Call 1-800-324-0045 or visit our web site www.lei-extras.com.
3) Canadian customers can write:
Lowrance/Eagle Canada, 919 Matheson Blvd. E. Mississauga, Ontario
L4W2R7 or fax 905-629-3118.
Shipping Information
If it becomes necessary to send a product for repair or replacement, you
must first receive a return authorization number from Customer
Service. Products shipped without a return authorization will not be
accepted. When shipping, we recommend you do the following:
1. Please do not ship the knobs or mounting bracket with your unit.
2. If you are sending a check for repair, please place your check in an
envelope and tape it to the unit.
3. For proper testing, include a brief note with the product describing
the problem. Be sure to include your name, return shipping address
and a daytime telephone number. An e-mail address is optional but
useful.
4. Pack the unit in a suitable size box with packing material to prevent
any damage during shipping.
5. Write the Return Authorization (RA) number on the outside of the
box underneath your return address.
6. For your security, you may want to insure the package through your
shipping courier. Lowrance does not assume responsibility for goods
lost or damaged in transit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Visit our web site:
Lowrance Pub. 988-0156-021
Printed in USA 020604
© Copyright 2004
All Rights Reserved
Lowrance Electronics, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|