Lowrance electronic GPS Receiver GLOBALMAP 4800M User Manual

Pub. 988-0151-182

Addendum I

LMS-480M, LMS-480DF &

GlobalMap^®4800M

This addendum addresses new items packed with your unit, changes to

installation procedures, and NMEA 2000^®upgrades not documented in

the LMS 480M, LMS-480cDF and GlobalMap 4800M manuals.

Your unit now packs with a 2-foot (61 cm) blue-to-red adapter cable, 15-

foot (4.6 m) extension cable, LGC-3000 GPS module, double T connector

and two 120-ohm terminators.

The segment covering changes in installation procedures provides new

backcase diagrams and information on how to add your unit to a new

NMEA 2000 standard DeviceNet network.

The upgrades covered in this document include information on the new

LGC-3000 and instructions on how to configure and calibrate NMEA

2000 devices through the NMEA 2000 menu.

NOTICE!

The storage and operation temperature range for your unit is from -20

degrees to +167 degrees Fahrenheit (-28 degrees to +75 degrees Cel-

sius). Extended storage or operation in temperatures higher or lower

than specified will damage the liquid crystal display in your unit. This

type of damage is not covered by the warranty.

Pack Assembly

Your unit is packed with a 2-foot blue-to-red adapter cable, making it

compatible with NMEA 2000 standard DeviceNet networks. Networks

consisting of LowranceNet™ red connectors and Micro-C™ connectors

are examples of a DeviceNet network. Your unit is also compatible with

LowranceNet blue connector networks.

To add your unit to a NMEA 2000 DeviceNet network, the blue end of

the blue-to-red adapter cable must be connected to the unit's network

socket; otherwise you will not be able to use the red connector cables and

devices that came with your unit. Red connector components packed with

the unit include: 15-foot extension cable, LGC-3000 GPS module, double

T connector and two 120-ohm terminators. Instructions and diagrams

covering the use of items packed with your unit are contained in the Power

Connections segment below.

Download from Www.Somanuals.com. All Manuals Search And Download.

Powering Your Display Unit

The display unit works from a 12-volt DC battery system. Attach the

display power cable (with provided 3-amp fuse) to an accessory switch

or power bus. If this results in electrical interference, connect direct to

a battery but install an in-line switch on the cable.

Caution:

We strongly recommend that you shut off the power supply to the

power cable when the unit is not in use, especially in saltwater en-

vironments. When the unit is turned off but still connected to a

power supply, electrolysis can occur in the power cable plug. This

may result in corrosion of the plug body along with the electrical

contacts in the cable and the unit's power socket. Risk of electroly-

sis corrosion is even greater when the cable is unplugged from the

unit, but still connected to a power source. We recommend you

connect the power cable to the auxiliary power switch included

in most boat designs. If that results in electrical interference, or

if such a switch is not available, we recommend connecting di-

rect to the battery and installing an in-line switch. This will let

you shut off power to the power cable when the unit is not in use.

When you are not using the unit, you should always shut off

power to the power cable, especially when the power cable is dis-

connected from the unit.

WARNING:

This product must be independently fused with the en-

closed 3-amp fuse (or equivalent), even if you connect to

a fused accessory or power bus.

If a malfunction happens inside the unit, extensive dam-

age can occur if the enclosed fuse is not used. As with all

electrical devices, this unit could be damaged to a point

that it is unrepairable and could even cause harm to the

user when not properly fused.

Failure to use a 3-amp fuse will void your warranty.

If possible, keep the power cable away from other boat wiring, especially

the engine's wires. This will provide the best isolation from electrical

noise. If the cable is not long enough, splice #18 gauge wire onto it.

The display power cable has three wires, white, red and black. Red is the

positive (+) lead, black is negative (–) or ground. The white wire is un-

used by your unit and should be capped. Make sure to attach the in-line

fuse holder to the red lead as close to the power source as possible.

Download from Www.Somanuals.com. All Manuals Search And Download.

For example, if you have to extend the power cable to the power bus or

battery, attach one end of the fuse holder directly to the power bus or

battery. This will protect both the unit and the power cable in the event

of a short.

This unit has reverse polarity protection. No damage will occur if the

power wires are reversed. However, the unit will not work until the

wires are attached correctly.

Power Diagram A

Mandatory

To unit

network

power-off

3-amp fuse

switch

NMEA 2000

Power Cable

Black

Red

Shield

3-amp fuse

Display Unit

Power Cable

Black

Recommended

display unit

power-off switch

White

(unused)

12 volt DC

power source

Data Cable

Use this method if you are powering the display unit and a GPS mod-

ule or the display unit and a NMEA 2000 network. (Fuses may be dif-

ferent from those shown.)

The network and any NMEA 2000 devices, including the GPS

module, will not operate unless the NMEA 2000 Power Cable is

connected to power. The NMEA 2000 power cable must be connected

to power even if your only NMEA 2000 device is the GPS module and it

is connected to the display unit's Network socket. (However, never

connect multiple power sources to a NMEA 2000 network.

The method in diagram B is also used when your display unit is con-

nected to a NMEA 2000 network that is already connected to power.

(Never connect multiple power sources to a NMEA 2000 network.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Powering a NMEA 2000 Network Bus

A NMEA 2000 bus must be connected to a power source to operate.

NMEA 2000 devices, including GPS modules, draw their power from

the network bus. If you have a pre-existing NMEA 2000 network instal-

lation, it may already be connected to another power source. If you are

not sure about a network's power status, consult the boat manufacturer

or dealer. If your NMEA 2000 bus is already powered, you can ignore the

NMEA 2000 Power cable and use the method shown in Power Diagram

B. Never attach two power sources to a single NMEA 2000 bus.

Power Diagram B

To unit

Red wire with

3-amp fuse

White wire

(unused)

Display Unit

Power Cable

All unused Data

or NMEA 2000

power wires

should be

capped with

wire nuts and

electrical tape

to prevent

Black wire

Recommended

power off switch

12 volt DC

power source

shorts.

Data Cable

NMEA 2000 Power Cable

Use this method if you are only powering your display unit and are not

powering a NMEA 2000 network or any NMEA 2000 accessory device,

including a GPS module. (Fuse may be different from that shown.)

If you do need to power your NMEA 2000 bus, attach the NMEA 2000

Power cable to an accessory switch as indicated in power diagram A on

page 4. The NMEA 2000 Power cable's red wire should be attached

(with provided 3-amp fuse) to the positive (+) terminal. The NMEA

2000 Power cable's black and shield wires should both be attached to

the negative (–) terminal.

WARNING:

The NMEA 2000 network bus is always on and constantly

drawing power. You must connect NMEA power to a

switched power source so you can turn off the network

Download from Www.Somanuals.com. All Manuals Search And Download.

when not in use. Failure to connect to and use a power

switch will drain your boat battery, which could stop

your boat's operation.

GPS Antenna/Receiver Module

Your unit packs with the LGC-3000 GPS module. This device contains

the unit's external antenna and receiver for GPS and WAAS signals.

The antenna/receiver module comes with a 15-foot (4.6 m) extension

cable. This module can be mounted on a flat surface or pole, or an op-

tional magnet is available for temporary mounting on any ferrous sur-

face.

You need to select an antenna installation location that has a clear, un-

obstructed view of the sky. After the module is installed, connect it to the

unit. The LGC-3000 can communicate with your GPS unit either directly

(using the supplied extension cable) or through a NMEA 2000 network.

LGC-3000 Module, bottom view (left) and top view (right).

NOTE

See the module’s instruction sheet, publication part number 988-

0154-651, for complete installation instructions.

To use the module in an automobile, you may achieve good results by

simply placing the external antenna on the top of the dash, at the base of

the windshield. A piece of the rubber non-skid shelf liner material avail-

able in recreational vehicle supply stores will help hold the antenna in

place. This may not work well if you have a cab-over design pickup truck

camper or motor home. If dashboard reception is poor, simply relocate

the antenna module elsewhere on the vehicle for a clearer view of the

sky.

Connecting to a NMEA 2000 Network

A network bus is an installed and operational network cable (backbone)

running the length of your boat, already connected to a power supply and

properly terminated. Such a bus provides network connection nodes at

various locations around your boat. The NMEA 2000 network is similar to

Download from Www.Somanuals.com. All Manuals Search And Download.

the telephone wiring in a house. If you pick up a phone in your living room,

you can hear someone talking into the phone in the bedroom.

Lowrance and LEI provide all the cables you will need to create a NMEA

2000 network. Lowrance provides T connectors and extension cables so

you can add devices along the backbone wherever you want. Once you

have a working network, every sensor added will come with its own T

connector for easy expansion.

The simplest NMEA 2000 network is a GPS or sonar/GPS display unit

with the LGC-3000, one double-T connector, two 120 ohm terminators

and any extension cables needed to connect them.

It is easy to expand this network by removing a terminator from one end

of the double T connector, then inserting a new T connector or extension

cable between the double T connector and terminator (See the NMEA

200 network general information document that came with your unit for

more information). For more information on connecting your unit to an

existing NMEA 2000 network, see the NMEA 2000 Networks General In-

formation document that was packed with your unit, publication part

number 988-0154-173.

NMEA 0183 Wiring

(Data cable)

To exchange NMEA 0183 data, this unit has one NMEA 0183 version

2.0 communication port. Com port one (Com-1) can be used to receive

NMEA format GPS data. The com port can also transmit NMEA format

GPS data to another device.

Orange (Receive)

NMEA Transmit

Ground

To Other

GPS Receiver

Com-1

To unit

Shield (Ground)

Com-1 wiring to receive NMEA position information

from some other GPS receiver.

Yellow (Transmit)

Shield (Ground)

NMEA Receive

Ground

Com-1

To unit

To Other

Device

Com-1 wiring to transmit NMEA position information

to another NMEA-compatible device.

The four wires for the com port are combined with the display unit

power cable and NMEA 2000 Power cable to form the power/data cable

(shown earlier). Com-1 uses the yellow wire to transmit, the orange

wire to receive and the shield wire for signal ground. Your unit does

not use the blue wire.

Download from Www.Somanuals.com. All Manuals Search And Download.

Network socket

Sonar socket

Power/Data socket

120 ohm terminator

Speed

sensor

Double T

connector

Display unit

power cable

Data

cable

NMEA-2000

Power cable

Blue-to-red

adapter cable

Extension

cable

Transducer

LGC-3000

Cable connections for LMS-480M and LMS-480DF.

Download from Www.Somanuals.com. All Manuals Search And Download.

Network socket

Power/Data socket

120 ohm terminator

Double T

connector

Display unit

power cable

Data

cable

Extension

cable

NMEA-2000

Power cable

Blue-to-red

adapter cable

LGC-3000

Cable connections for the GlobalMap 4800M.

Download from Www.Somanuals.com. All Manuals Search And Download.

NMEA 2000 Device Configuration

The NMEA 2000 menu on your display unit's main menu allows you to

configure, calibrate and monitor devices on a NMEA 2000 network. The

NMEA 2000 menu provides access to the Bus Setup, Fuel Management

and NMEA 2000 Alarms. You also can turn on/off Waypoint Sharing

and Backlight Synchronization from the NMEA 2000 menu.

NOTE:

The menus in your unit may differ slightly from the screen cap-

tures used in this document. Your unit, however, will perform the

same NMEA 2000 functions in a similar manner.

Bus Setup highlighted on the NMEA 2000 menu.

Bus Setup

Selecting Bus Setup from the NMEA 2000 menu gives you access to the

Bus Configuration menu and the NMEA Diagnostics and Ethernet Di-

agnostics pages. The Bus Configuration menu allows you to choose an

engine-tank configuration and manage devices on the network. When

the Bus Configuration menu is accessed, a list will appear of all NMEA

2000 devices on the network.

Bus Configuration menu (left). NMEA Diagnostics page (center).

Ethernet Diagnostics (right).

Download from Www.Somanuals.com. All Manuals Search And Download.

The NMEA Diagnostics page displays information about the perform-

ance of the network bus, keeping you updated on bus status, mode, er-

rors and bus traffic. The Ethernet Diagnostics page keeps you updated

on the performance of an Ethernet connection (if applicable) supplying

information ranging from IP Address to upload and download rates

(bytes per second). To refresh either Diagnostics page, highlight the

PING ALL DEVICES button at the bottom of the page and press ENT.

The network devices list is located in the top half of the Bus Configura-

tion menu. You can configure, calibrate and set alarms for devices ac-

cessed from the Bus Configuration menu network devices list.

The Engine-Tank Configuration and Tank Select menus as well as the

Tank Size dialog box are located on the bottom half of the Bus Configu-

ration menu. The Set Configuration button — positioned next to the

engine-tank configuration menu — allows you to finalize a selected con-

figuration.

Bus Configuration menu with list of network devices. Engine-Tank

Configuration and Tank Select menus are at the bottom of the screen.

NOTE:

If you have not used the LMF-200 or LMF-400 to choose an engine-

tank configuration for your vessel, you must use your display unit

to select a configuration.

Engine & Tank Configuration

The Engine-Tank configuration menu is located below the NMEA 2000

Devices list, but will only be accessible if a Suzuki engine Interface,

EP-10 Fuel Flow, EP-15 Fluid Level, EP-45 Pressure Sensor or EP-50

Storage Device are on the network. When choosing an engine-tank con-

figuration you will use the Tank Select menu, Tank Size dialog box and

Set configuration button, all detailed below.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tank Select

The Tank Select menu allows you to choose from up to three tanks

(Port, Center and Starboard), depending on the Engine-tank configura-

tion that has been selected. This allows you to set up each tank indi-

vidually.

Tank Size

The Tank Size menu allows you to input the size of a selected tank in

gallons. After selecting the desired tank from the Tank Select menu,

you are ready to enter the tank's size.

Set Configuration button

The Set Configuration button is used to finalize engine-tank configura-

tion settings.

Setting Engine-Tank Configuration:

1. Press MENU| MENU, use ↓ ↑ to highlight NMEA 2000 and press ENT.

2. The NMEA 2000 menu will appear with five options: Bus Setup,

Fuel Management, NMEA 2000 Alarms, Waypoint Sharing and Back-

light Synchronization. Choose BUS SETUP and press ENT.

1 Engine/1Tank highlighted on Engine and Tank Configuration

menu (left). Starboard highlighted on Tank Select menu (center).

Tank Size set to 40 gallons (right).

3. Select ENGINE & TANK CONFIG and press ENT, which will open the Engine

& Tank Configuration menu with the following configuration options: 1

Engine/1 Tank, 1 Engine/2 Tanks, 2 Engines/1 Tank, 2 Engines/2

Tanks, 3 Engines/1 Tank, 3 Engine/3 Tanks and Unconfigured Bus.

4. Choose the configuration that matches the number of engines and

tanks on your vessel and press ENT.

5. Highlight TANK SELECT and press ENT, which will open the Tank Select

menu.

6. Select the tank you want to set up and press ENT. Press → to high-

light the Tank Size dialog box and press ENT.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Use ↓ ↑, ← → to input the capacity (gallons) of the tank you chose

from the Tank Select menu and press ENT.

8. Repeat Steps 5-7 for each remaining tank.

9. When all tanks have been configured, press the SET CONFIGURATION but-

ton. The following confirmation message will appear: Are you sure you

wish to change the bus configuration? Choose YES and press ENT, Press

EXIT to get back to the main display.

Device Configuration Menu

When a device is selected from the network devices list on the Bus Con-

figuration menu, its Device Configuration menu will appear. Device

configuration menus vary among devices. Available functions on device

configuration menus allow you to change device names, tank sizes,

fluid types and provide access to the Advanced Options menu. We will

cover configuration and calibration later in this section.

If you do not have an EP-15 Fluid Level, EP-10 Fuel Flow or EP-20 En-

gine Interface on the network, the Bus Configuration menu will not

display the Engine-Tank Configuration menu, Tank Select menu, Tank

Size menu or Set Configuration button.

Device Information and Device Data

The Device information panel, located to the left of the Device Configu-

ration menu, displays information on the selected device that includes,

software version, model, address, serial number, instance and current

status.

Device Data is shown in the Device Data window at the bottom of the

device configuration menu. The information displayed in the Device

Data window will vary among devices. If, for example, you are viewing

the device configuration menu for an EP-15 Fluid Level, the device

data window will include tank size and the amount of fuel left in the

tank.

Download from Www.Somanuals.com. All Manuals Search And Download.

The Device Data for an EP-10 Fuel Flow includes Fuel Rate (amount of

fuel burned per hour), Fuel Used, Trip Fuel Used and Seasonal Fuel

Used.

NOTE:

If, as in the graphic above, you do not have a Suzuki Engine Inter-

face, EP-15 Fluid Level or EP-10 Fuel Flow on the network, the

Engine & Configuration menu, Tank Select menu, Tank Size dialog

and Set Configuration button will not be displayed on the Bus Con-

figuration menu.

Fuel Management Menu

The Fuel Management menu gives you access to the following options:

Tank Location, Fuel Added, Add Fuel, Fill Tank, Engine Select, Reset

Calibration, Reset Trip and Reset Seasonal. Those options allow you to

configure, calibrate, reset calibration, reset trip fuel and reset seasonal

fuel for select NMEA 2000 devices. We will cover configuration and cali-

bration procedures later in this section.

Fuel Management highlighted on the NMEA 2000 menu (left).

Fuel Management menu (right).

Tank Location

If you chose an engine-tank configuration with more than one tank, you

will be able to switch the tank location (configuration) in the Tank Lo-

cation menu. When fuel is added to a tank, you will select the correct

tank from the Tank Location menu, then input the amount of fuel

added in the Fuel Added dialog box.

Fuel Added

Used in tandem with the Add Fuel command, the Fuel Added dialog

box allows you to input the amount of fuel added to the tank, when an

amount of fuel is added that does not fill up the tank.

Download from Www.Somanuals.com. All Manuals Search And Download.

Add Fuel

After entering the amount of fuel added to a tank in the Fuel Added

dialog, the Add Fuel command finalizes the entry of the data. Like the

Fuel Added dialog, the Add Fuel command will only be used when an

amount of fuel is added that does not fill up the tank.

Fill Tank

You will use the Fill Tank command when calibrating a fuel flow and

when filling up the tank without calibration.

Adding Fuel to Tank

Tank Location, Fuel Added and Add Fuel commands work together to

keep NMEA 2000 fuel data consistent with the actual amount of fuel

added to the fuel tank(s).

1. Press MENU|MENU, select NMEA 2000 and press ENT.

2. The NMEA 2000 menu will appear with five options: Bus Setup,

Fuel Management, NMEA 2000 Alarms, Waypoint Sharing and Back-

light Synchronization. Select FUEL MANAGEMENT and press ENT.

3. Highlight TANK LOCATION and press ENT. The Tank Location menu will

appear with up to three options: Port, Center and Starboard.

4. Select the tank you added fuel to and press ENT.

5. Follow the steps below that apply to your tank.

If you filled up the tank:

A. Press the FILL TANK button and press ENT. The following message will

appear: Are you sure you wish to Fill Tank? Press ENT. Another mes-

sage will appear: Do you wish to re-calibrate the device? Highlight NO

and press ENT.

If you did not fill up the tank:

B. Highlight FUEL ADDED and press ENT to access the FUEL ADDED dialog

box. Use ↑ ↓ , ← → to input the amount of fuel added to the tank and

press ENT. Select the ADD FUEL button and press ENT. The following mes-

sage will appear: Are you sure you wish to Add Fuel? Highlight YES and

press ENT.

6. Press EXIT repeatedly to get back to the main display.

Engine Operations

The lower half of the Fuel Management menu contains the following

Engine Operation functions: Engine Select, Reset Calibration, Reset

Trip and Reset Seasonal.

Engine Select

Engine Select allows you to choose the desired engine when resetting

calibration, resetting trip fuel and resetting seasonal fuel.

Download from Www.Somanuals.com. All Manuals Search And Download.

To Reset Calibration:

Choosing the Reset Calibration command will switch fuel flow calibra-

tion settings back to factory defaults.

1. Press MENU|MENU, select NMEA 2000 and press ENT.

2. Highlight FUEL MANAGEMENT and press ENT. The Fuel Management

menu will appear.

3. Highlight to ENGINE SELECT and press ENT. Select the desired engine —

the engine attached to the desired fuel flow — and press ENT.

4. Highlight RESET CALIBRATION and press ENT. The following confirma-

tion message will appear: Are you sure you wish to Reset Calibration?

Select YES and press ENT. Calibration settings for the selected fuel have

been returned to factory defaults.

To Reset Trip:

The Reset Trip function allows you to reset to zero the running total of

fuel used on a particular trip.

1. Press MENU|MENU, select NMEA 2000 and press ENT.

2. Highlight FUEL MANAGEMENT and press ENT. The Fuel Management

menu will appear.

3. Select RESET TRIP and press ENT. The following confirmation message

will appear: Are you sure you wish to Reset Trip? Highlight YES and

press ENT. The Trip Fuel Used figure has been reset to zero.

To Reset Seasonal:

Your unit can track fuel usage not only for trips, but also for entire sea-

sons. The reset seasonal command allows you to reset to zero the run-

ning total of fuel used during a season.

1. 1. Press MENU|MENU, select NMEA 2000 and press ENT.

2. Highlight FUEL MANAGEMENT and press ENT. The Fuel Management

menu will appear.

3. Select RESET SEASONAL and press ENT. The following confirmation mes-

sage will appear: Are you sure you wish to Reset Seasonal?

Highlight YES and press ENT. The Seasonal Fuel Used figure has been

reset to zero.

NMEA 2000 Alarms

The NMEA 2000 Alarms menu allows you to set Full and Empty fuel

alarms for the EP-10 Fuel Flow, EP-15 Fluid Level, EP-50 Storage De-

vice and the Suzuki Engine Interface. The alarms may be set to a per-

centage (0-100%) of tank capacity.

Download from Www.Somanuals.com. All Manuals Search And Download.

The second tab at the top of the NMEA 2000 Alarms page is the Alarm

Status Tab. When an alarm has been set for a device, the alarm and its

current status will be shown on the Alarm Status window. To view the

Alarm Status window, highlight the Alarm Status tab and press ENT.

To set NMEA 2000 Alarm:

1. Press MENU|MENU, select NMEA 2000 and press ENT.

2. Highlight NMEA 2000 ALARMS and press ENT.

3. Highlight FLUID LEVEL DEVICE and press ENT. Use ↑ ↓ to select the de-

vice you want to set an alarm for and press ENT.

4. Highlight the ENABLED box next to the desired alarm (Full Alarm or

Empty Alarm) and press ENT to turn on the alarm.

5. To set the alarm percentage, press → to highlight PERCENT and press

ENT.

6. Use ↑ ↓, ← → to input the desired percentage and press ENT. Repeat

Steps 3-4 to set the other alarm.

7. Highlight SET CONFIGURATION and press ENT to finalize alarm settings.

Press EXIT repeatedly to get back to the main display.

NOTE:

To turn off (uncheck) an alarm, highlight its ENABLED BOX and press

ENTER.

Waypoint Sharing

Waypoint Sharing allows you to share a waypoint from one display unit

with display units across the network.

To turn on/off Waypoint Sharing:

1. Press MENU|MENU, select NMEA 2000 and press ENT.

2. Highlight WAYPOINT SHARING and press ENT which will turn on/off way-

point sharing.

3. Press EXIT repeatedly to get return to the main display.

Backlight Synchronization

The Backlight Synchronization command will keep all display unit

backlight levels consistent across the NMEA 2000 network. So, if you

set the backlight level to 75% on one display unit, all other units on the

network will automatically switch to the same setting.

To turn on/off Backlight Synchronization:

1. Press MENU|MENU, select NMEA 2000 and press ENT.

2. Highlight BACKLIGHT SYNCHRONIZATION and press ENT, which will turn

on/off Backlight Synchronization.

3. Press EXIT repeatedly to get back to the main display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Configuring EP Sensors

All configurable devices are configured through their Device Configura-

tion menus, which may be accessed through the network devices list on

the Bus Configuration menu.

EP-35 Temperature Configuration

To input Device Name:

1. Press MENU|MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Select the temp sensor you want to rename and press ENT. The De-

vice Configuration menu will appear with the Device Name dialog box

highlighted.

4. Press ENT and use ↑ ↓, ← → to input the desired name for the temp

sensor. Press ENT. Press EXIT repeatedly to get back to the main dis-

play.

To select Temp Type:

1. Press MENU|MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Select the desired temp sensor and press ENT. The Device Configura-

tion menu will appear.

4. Highlight TEMP TYPE and press ENT. The following list of Temp Types

will appear: Water, Outside, Inside, Engine Room, Cabin, Live Well,

Bait Well, Refigeration, Heating System and Unknown.

5. Highlight the desired Temp Type and press ENT. The following con-

firmation message will appear: Are you sure you wish to change this

device's configuration?

6. Highlight YES and press ENT. Press EXIT repeatedly to get back to the

main display.

Advanced Options menu

The Temp sensor Advanced Options menu contains two categories: In-

stance and Restore Defaults.

Download from Www.Somanuals.com. All Manuals Search And Download.

Instance

The Instance command is intended for use only by experienced NMEA

2000 network technicians. Instance allows network technicians to re-

solve certain electronic probe conflicts. This is most likely to occur if the

network includes LMF-200 or LMF-400 digital gauges, which support

the display of fewer electronic probes than your GPS or sonar/GPS unit.

If you want to use your unit in a network including one of these digital

gauges, you may need to consult customer service.

You should never need this command if you are connecting your unit to

a network with similar display units and/or a series of electronic

probes.

Restore Defaults

The Restore Defaults command allows you to reset an individual EP-35

Temp Sensor's settings to factory defaults. If, for example, you execute

the Restore Defaults command from your Water Temp's Advanced Op-

tions menu, only the settings for the Water Temp will be reset to fac-

tory defaults. Other temps on the network will not be affected.

To restore default settings:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Select the desired temp sensor and press ENT. The Device Configura-

tion menu will appear.

4. Highlight ADVANCED OPTIONS and press ENT.

5. Select RESTORE DEFAULTS and press ENT. The following message will

appear: Are you sure you wish to change this device's configuration?

6. Highlight YES and press ENT. Press EXIT repeatedly to get back to the

main display.

EP-10 Fuel Flow Configuration

To input Device Name:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Select the fuel flow you want to rename and press ENT. The Device

Configuration menu will appear with the Device Name dialog box high-

lighted.

4. Press ENTER and use ↑ ↓, ← → to input the desired name for the fuel

flow. Press ENT. Press EXIT repeatedly to get back to the main display.

To select a Location:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Select the desired fuel flow and press ENT. The Device Configuration

menu will appear.

4. Select LOCATION and press ENT, which will open the Location menu

with following options: Port, Center, Starboard and Unknown.

5. Highlight the desired location and press ENT. The following message

will appear: Are you sure you wish to change this device's configuration?

5. Select YES and press ENT. Press EXIT repeatedly to get back to the

main display.

Advanced Options menu

The Fuel Flow sensor Advanced Options menu contains two categories:

Instance and Restore Defaults.

Instance

The Instance command is intended for use only by experienced NMEA

2000 network technicians. Instance allows network technicians to re-

solve certain electronic probe conflicts. This is most likely to occur if the

network includes LMF-200 or LMF-400 digital gauges, which support

the display of fewer electronic probes than your GPS or sonar/GPS unit.

If you want to use your unit in a network including one of these digital

gauges, you may need to consult customer service. You should never

need this command if you are connecting your unit to a network with

similar display units and/or a series of electronic probes.

Restore Defaults

The Restore Defaults command allows you to reset an individual EP-10

Fuel Flow Sensor's settings to factory defaults. If, for example, you exe-

cute the Restore Defaults command from your Port Fuel Flow Ad-

vanced Options menu, only the settings for the Port Fuel Flow will be

reset to factory defaults. Other fuel flows on the network will not be

affected.

Download from Www.Somanuals.com. All Manuals Search And Download.

To restore default settings:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Use ↑ ↓ to select the desired fuel flow and press ENT. The Device

Configuration menu will appear.

4. Highlight ADVANCED OPTIONS and press ENT.

5. Select RESTORE DEFAULTS and press ENT. The following message will

appear: Are you sure you wish to change this device's configuration?

6. Highlight YES and press ENT. Press EXIT repeatedly to get back to the

main display.

EP-15 Fluid Level Configuration

To input Device Name:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Select a fluid level you want to rename and press ENT. The Device

Configuration menu will appear with the Device Name dialog box high-

lighted.

4. Press ENT and use ↑ ↓, ← → to input the desired name for the fluid

level. Press ENTER. Press EXIT repeatedly to get back to the main dis-

play.

To select Tank Instance (Location):

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Select the desired fluid level and press ENT. The Device Configura-

tion menu will appear.

4. Highlight TANK INSTANCE and press ENT, which will open the Tank In-

stance menu with the following options: Tank 1, Tank 2, Tank 3 and

Unknown.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Select the desired Tank Instance (location) and press ENT. The fol-

lowing confirmation message will appear: Are you sure you wish to

change this device's configuration?

6. Highlight YES and press ENT. Press EXIT repeatedly to get back to the

main display.

To select Fluid Type:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Select the desired fluid level and press ENT. The Fluid Level Device

Configuration menu will appear.

4. Press ↓ to FLUID TYPE and press ENT, which will open the Fluid Type

menu with the following options: Fuel, Water, Gray Water, Live Well,

Oil, Black Water and Unknown.

5. Select the desired fluid type and press ENT. The following message

will appear: Are you sure you wish to change this device's configuration?

6. Highlight YES and press ENT. Press EXIT repeatedly to get back to the

main display.

To input Tank Size:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Select the desired fluid level and press ENT. The Fluid Level Device

Configuration menu will appear.

4. Highlight TANK SIZE and press ENT. Use ↑ ↓ ,← → to input the size of

the tank and press Enter. The following message will appear: Are you

sure you wish to change this device's configuration?

5. Select YES and press ENT. Press EXIT repeatedly to get back to the

main display.

Advanced Options menu

The Fuel Flow sensor Advanced Options menu contains two categories:

Instance and Restore Defaults.

Download from Www.Somanuals.com. All Manuals Search And Download.

Instance

The Instance command is intended for use only by experienced NMEA

2000 network technicians. Instance allows network technicians to re-

solve certain electronic probe conflicts. This is most likely to occur if the

network includes LMF-200 or LMF-400 digital gauges, which support

the display of fewer electronic probes than your GPS or sonar/GPS unit.

If you want to use your unit in a network including one of these digital

gauges, you may need to consult customer service.

You should never need this command if you are connecting your unit to

a network with similar display units and/or a series of electronic

probes.

Restore Defaults

The Restore Defaults command allows you to reset an individual EP-15

Fluid Level Sensor's settings to factory defaults. If, for example, you

execute the Restore Defaults command from your Gray Water Fluid

Level Advanced Options menu, only the settings for the Gray Water

Fluid Level will be reset to factory defaults. Other fluid levels on the

network will not be affected.

To restore default settings:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Select the desired fluid level and press ENT. The Device Configura-

tion menu will appear.

4. Highlight ADVANCED OPTIONS and press ENT.

5. Select RESTORE DEFAULTS and press ENT. The following message will

appear: Are you sure you wish to change this device's configuration?

6. Highlight YES and press ENT. Press EXIT repeatedly to get back to the

main display.

NOTE:

The Fluid Level Device Configuration menu also contains the Cali-

brate button, but we will address that later in the segment covering

Calibration.

Download from Www.Somanuals.com. All Manuals Search And Download.

Suzuki Engine Interface Configuration

To input Device Name:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Use ↑ ↓ to select the engine interface you want to rename and press

ENT. The Device Configuration menu will appear with the Device Name

dialog box highlighted.

4. Press ENT and use ↑ ↓, ← → to input a name for the interface. Press

ENT. Press EXIT repeatedly to return to the main display.

To select a Location:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Select the desired engine interface and press ENT. The Device Con-

figuration menu will appear.

4. Highlight LOCATION and press ENT, which will open the Location menu

with the following options: Port, Center, Starboard and Unknown.

5. Select the desired location and press ENT. The following confirmation

message will appear: Are you sure you wish to change this device's con-

figuration?

6. Press ENT. Press EXIT repeatedly to get back to the main display.

To select Engine Type:

1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The

NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man-

agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn-

chronization.

2. Highlight BUS SETUP and press ENT, which will open the Bus Configu-

ration menu. A list of network devices will be at the top of the page.

3. Use ↑ ↓ to select the desired engine interface and press ENT. The De-

vice Configuration menu will appear.

4. Highlight ENGINE TYPE and press ENT, which will open the Engine

Type menu with the following options: DF40, DF50, DF60, DF70,

DF90/115, DF140, DF150, DF175, DF200/225, DF250 and DF300.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Select your engine type and press ENT. The following message will

appear: Are you sure you wish to change this device's configuration?

6. Highlight YES and press ENT. Press EXIT repeatedly to get back to the

main display.

Advanced Options menu

The Engine Interface Advanced Options menu contains three catego-

ries: Instance, Restore Defaults and Reset Trim Calibration.