Pub. 988-0151-331
www.lowrance.com
®
GlobalMap 6500C,
®
GlobalMap 6600C HD,
®
GlobalMap 7500C,
®
GlobalMap 7600C HD,
Mapping GPS Receivers
Operation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Section 1: Read Me First!.........................................................1
How Lowrance GPS Works .......................................................... 2
Introduction to GPS and WAAS................................................... 4
How to use this manual: typographical conventions .................. 7
Arrow Keys................................................................................ 7
Keyboard ................................................................................... 7
Menu Commands ...................................................................... 7
Instructions = Menu Sequences ............................................... 7
Section 2: Installation & Accessories....................................9
Preparations.................................................................................. 9
GPS Antenna/Receiver Module.................................................... 9
Connecting Directly to the Unit............................................. 10
Connecting to a NMEA 2000 Network................................... 10
Power Connections...................................................................... 11
Powering a NMEA-2000 Buss ................................................ 12
Powering Your Unit................................................................ 13
External Speaker .................................................................... 14
NMEA 2000 Cable Connections................................................. 15
Connecting to a NMEA 2000 Network................................... 15
NMEA 0183 Cable Connections................................................. 16
NMEA 0183 Wiring Diagrams ............................................... 16
Mounting the Unit: Bracket, In-Dash or Portable.................... 19
Bracket Installation................................................................ 19
In-Dash Installation ............................................................... 21
Portable Installation............................................................... 22
MMC or SD Memory Card Installation ..................................... 22
To remove an MMC or SD Card............................................. 24
To add an MMC or SD Card................................................... 24
Other Accessories........................................................................ 24
Face Cover................................................................................... 25
Section 3: Basic GPS Operations .........................................27
Keyboard ..................................................................................... 27
Power/lights on and off............................................................... 28
Main Menu.................................................................................. 28
Pages ........................................................................................... 30
Satellite Status Page .............................................................. 30
Navigation Page...................................................................... 31
Map Page................................................................................. 34
GPS Quick Reference.................................................................. 39
Find Your Current Position........................................................ 40
Moving Around the Map: Zoom & Cursor Arrow Keys............. 40
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting Any Map Item with the Cursor.................................. 41
Searching..................................................................................... 41
Set a Waypoint............................................................................ 43
To create and save a Waypoint .............................................. 43
Navigate To a Waypoint............................................................. 45
Set Man Overboard (MOB) Waypoint........................................ 46
Navigate Back to MOB Waypoint.............................................. 46
Navigate to Cursor Position on Map.......................................... 47
Navigate to a Point of Interest................................................... 49
Creating and Saving a Trail....................................................... 49
To Save a Trail........................................................................ 49
Displaying a Saved Trail ............................................................ 51
To turn off trail display: ......................................................... 51
To turn on trail display:.......................................................... 51
Navigating Trails........................................................................ 51
Visual Trailing ........................................................................ 52
Navigate a Trail (forward)...................................................... 52
Navigate a Back Trail (backtrack, or reverse)....................... 54
Transfer Custom Maps and GPS Data Files............................. 55
Custom Maps........................................................................... 55
GPS Data files......................................................................... 55
Cancel Navigation....................................................................... 57
Section 4: Advanced GPS Operations.................................59
Find Distance to Another Location............................................ 59
Find Distance From Point to Point............................................ 59
Icons............................................................................................. 59
Create Icon on Map................................................................. 60
Create Icon at Current Position............................................. 60
Delete an Icon ......................................................................... 60
Navigate to an Icon................................................................. 61
Routes.......................................................................................... 61
Create and Save a Route ........................................................ 62
Delete a Route......................................................................... 64
Edit a Route ............................................................................ 64
Navigate a Route..................................................................... 65
Navigate a Route in Reverse .................................................. 66
Trails ........................................................................................... 67
Delete a Trail .......................................................................... 67
Edit a Trail Name ................................................................... 67
Edit a Trail Color .................................................................... 68
Edit a Trail Pattern ................................................................ 68
Utilities........................................................................................ 68
Alarm Clock............................................................................. 69
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Sun/Moon Rise & Set Calculator............................................ 69
Trip Calculator........................................................................ 69
Trip Down Timer..................................................................... 69
Trip Up Timer ......................................................................... 69
Waypoints.................................................................................... 69
Delete a Waypoint................................................................... 69
Edit a Waypoint ...................................................................... 69
Selecting a Waypoint .............................................................. 70
Set a Waypoint by Average Position...................................... 70
Set a Waypoint by Projecting a Position................................ 70
Section 5: System & GPS Setup Options............................73
Alarms ......................................................................................... 73
Auto Satellite Search.................................................................. 74
Check MMC Files and Storage Space........................................ 75
Communications Port Configuration......................................... 75
Configure NMEA ........................................................................ 76
Coordinate System Selection...................................................... 76
To setup Loran TD:................................................................. 78
Map Fix.................................................................................... 78
Configure a map fix:................................................................ 78
Customize Page Displays ........................................................... 79
GPS Simulator ............................................................................ 80
To get to the GPS Simulator: ................................................. 81
Simulating Trail or Route Navigation ................................... 81
Initialize GPS.............................................................................. 82
Map Auto Zoom........................................................................... 82
Map Data..................................................................................... 82
Earth Map Detail.................................................................... 83
Pop-up Map Info...................................................................... 83
Draw Map Boundaries............................................................ 83
Fill Water with White............................................................. 83
Trackline Extension................................................................ 83
Presentation Mode.................................................................. 84
Safety Contour ........................................................................ 84
Map Overlays (Range Rings; Lat/Long Grid) ........................ 84
Map Datum Selection ................................................................. 85
Map Detail Category Selection................................................... 85
Map Orientation ......................................................................... 86
Navionics Charts....................................................................... 87
To display a Navionics chart: ................................................. 87
Port Information ..................................................................... 88
To view Port Services information:........................................ 88
Tidal Current Information ..................................................... 89
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
To view Tidal Current information:....................................... 90
Tide Information..................................................................... 91
To view tide information:........................................................ 91
Overlay Data............................................................................... 93
To overlay information on your screen: ................................. 94
To remove overlaid data: ........................................................ 94
To move overlaid data:............................................................ 95
Overylay Data Style................................................................ 96
Pop-up Help................................................................................. 99
Reset Options............................................................................ 100
Screen Contrast and Brightness .............................................. 100
Set Language ............................................................................ 101
Set Local Time .......................................................................... 102
Show WAAS Alarm................................................................... 103
Software Version Information.................................................. 103
Sounds and Alarm Sound Styles.............................................. 104
Track Smoothing....................................................................... 105
Trail Options............................................................................. 105
Delete All Trails.................................................................... 105
Update Trail Option.............................................................. 106
Delete Trail ........................................................................... 107
New Trail............................................................................... 107
Trail Visible/Invisible and Other Trail Options .................. 107
Transparency (available in some models)................................ 107
To adjust Menu Transparency level:.................................... 108
Units of Measure....................................................................... 108
Section 6: Searching ............................................................109
Find Addresses.......................................................................... 109
Find Any Item Selected by Map Cursor .................................. 112
Find Interstate Highway Exits ................................................ 112
Find Map Places or Points of Interest (POI) ........................... 115
Find Streets or Intersections.................................................... 116
Find a Street ......................................................................... 116
Find an Intersection ............................................................. 118
Find Waypoints......................................................................... 120
Section 7: Supplemental Material .....................................123
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
v
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD
TO OBTAIN POSITION INFORMATION.
CAUTION
When showing navigation data to a position (waypoint), a GPS unit will show
the shortest, most direct path to the waypoint. It provides navigation data to the
waypoint regardless of obstructions. Therefore, the prudent navigator will not
only take advantage of all available navigation tools when traveling to a way-
point, but will also visually check to make sure a clear, safe path to the waypoint
is always available.
WARNING!
When a GPS unit is used in a vehicle, the vehicle operator is solely re-
sponsible for operating the vehicle in a safe manner. Vehicle operators
must maintain full surveillance of all pertinent driving, boating or fly-
ing conditions at all times. An accident or collision resulting in damage
to property, personal injury or death could occur if the operator of a
GPS-equipped vehicle fails to pay full attention to travel conditions and
vehicle operation while the vehicle is in motion.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Read Me First!
How this manual can get you out on the road, fast!
Welcome to the exciting world of GPS satellite navigation! We know
you're anxious to begin finding your way with this space-age technol-
ogy, but we have a favor to ask. Before you grab the GlobalMap and
begin installing it, please give us a moment or two to explain how our
manual can help you get the best performance from your high-
resolution, high-performance GPS+WAAS chart recorder.
First, we want to thank you for buying a Lowrance GPS unit. Whether
you're a first time user or a professional navigator, you'll discover that
your GlobalMap is easy to use, yet capable of handling demanding
navigation tasks. When you team your unit with our custom mapping
software MapCreate 6, you have an incredible combination. No other
consumer GPS mapping system on the market offers so much informa-
tion and so many features in one package.
Our goal for this book is to get you on the road fast, with a minimum of
fuss. Like you, we'd rather spend more time navigating and less time
reading the manual!
So, we designed our book so that you don't have to read the whole thing
from front to back for the information you want. At the start (or end) of
each segment, we'll tell you what content is coming up next. If it's a
concept you're already familiar with, we'll show you how and where to
skip ahead for the next important topic. We've also made it easy to look
up any tips you may need from time to time. Here's how:
The manual is organized into 7 sections. This first section is an intro-
duction to Lowrance GPS. It tells you the basics you need to know be-
fore you can make the unit look around and tell you where you are.
Section 2 will help you install your unit and the GPS antenna module.
We'll show you how to get the MultiMedia Card (MMC) correctly in-
stalled inside the unit. We'll also tell you about some of the available
accessories.
Section 3 covers Basic GPS Operation. It will show you how easy it is to
run the GlobalMap, right out of the box. This section features a one-
page GPS Quick Reference. (If you've already jumped ahead and
figured out how to install the unit yourself, and you just can't
wait any longer, turn to the Quick Reference on page 39 and
head for the road with your GPS unit!)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 contains short, easy-to-scan GPS lessons that follow one an-
other in chronological order. They're all you'll need to know to find your
way on the water or in the wilderness quickly.
After you've learned the basics (or if you already have some GPS expe-
rience), you may want to try out some of the GlobalMap's many ad-
vanced navigation features. That brings us to Section 4, Advanced GPS
Operations. This section contains the rest of the unit's GPS command
functions, organized in alphabetical order.
When you come to a GPS menu command on the GlobalMap's screen, you
can look it up in the manual by skimming over the table of contents, just
flipping through Section 3 or scanning through the command portion of
Section 4.
This unit is ready to use right out of the box, but you can fine tune and cus-
tomize its operation with dozens of options. We describe how to use general
system options along with GPS options in Section 5, System Setup and
GPS Setup Options. Section 5 is organized in alphabetical order.
In Section 6, we go into more detail on one of the GlobalMap's most re-
markable capabilities — Searching. We'll introduce a search example in
the Basic GPS Operation section, but there are so many map items you
can search for, we had to give this function its own section in the man-
ual! For example, did you know this unit can look up business phone
numbers, functioning as a virtual Yellow Pages? We’ll show you how in
Section 6.
Finally, in Section 7, we offer Supplemental Material, including a list of
the GPS datums used, warranties and customer service information.
NOTICE!
The storage and operation temperature range for your GlobalMap
is from -4 degrees to +167 degrees Fahrenheit (-20 degrees to +75
degrees Celsius). Extended storage or operation in temperatures
higher or lower than specified will damage the liquid crystal display
in your unit. This type of damage is not covered by the warranty.
For more information, contact the factory's Customer Service De-
partment; phone numbers are listed on the last page.
How Lowrance GPS Works
You'll navigate faster and easier if you understand how the GlobalMap
scans the sky to tell you where you are on the earth — and, where
you're going. (But if you already have a working understanding of GPS
receivers and the GPS navigation system, skip on ahead to Section 2,
Installation & Accessories on page 9. If you're new to GPS, read on, and
2
Download from Www.Somanuals.com. All Manuals Search And Download.
you can later impress your friends with your new-found knowledge.)
First, think of your unit as a small but powerful computer. (But don't
worry — we made it easy to use, so you don't need to be a computer ex-
pert to find your way!) The GlobalMap includes a keypad and a screen
with menus so you can tell it what to do. The screen also lets the unit
show your location on a moving map, as well as point the way to your
destination.
This gimbal-mounted GlobalMap uses an external antenna/receiver
module, which makes the whole system work something like your car
radio. But instead of your favorite dance tunes, this receiver tunes in to
a couple of dozen GPS satellites circling the earth. (It will also listen in
to the WAAS satellites in orbit, but more about that in the upcoming
segment introducing you to GPS and WAAS.)
Your unit listens to signals from as many satellites as it can "see" above
the horizon, eliminates the weakest signals, then computes its location
in relation to those satellites. Once the GlobalMap figures its latitude
and longitude, it plots that position on the moving map shown on the
screen. The whole process takes place several times a second!
The performance doesn't stop there. Stored in the permanent memory
of each unit is a basic background map of the entire world. We lock it in
here at the factory — you can't change or erase this map.
The background map is suitable for many navigation chores, but for
maximum accuracy and much more detail, you need our optional map-
making software, MapCreate 6. (This complete set of mapping data is
already installed on the GlobalMap 6600 and GlobalMap 7600.) Some
unit features — such as searching for businesses and addresses —
won't work without a custom MapCreate map. There is so much detail
in our background map (and even more in MapCreate) that we'll de-
scribe their contents and differences in Section 3, Basic GPS Opera-
tions, on page 27.
Another portion of the GlobalMap's onboard memory is devoted to record-
ing GPS navigation information, which includes waypoints, event marker
icons, trails and routes. This lets you look back the way you came. Think
of this data storage like the hard drive memory in a computer or a tape in
a cassette tape recorder. You can save several different GPS data files,
erase 'em and record new ones, over and over again. Like any computer
file, these GPS Data Files (file format *.usr) can be shared between
Lowrance GPS or sonar/GPS units or even personal computers.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
This GlobalMap has one more thing in common with a personal com-
puter. Just as computers have a floppy disk drive for storing and ex-
changing files, the unit has a slot for an MMC (MultiMedia Card) or SD
(Secure Digital) card flash memory card. These solid-state memory de-
vices are about the size of a postage stamp, but can hold data ranging
from 8 MB to 1 GB in size. (Compare that to a floppy disk's 1.44 MB ca-
pacity!) This unit uses all that MMC space for two key GPS purposes.
First, you can backup your onboard GPS Data Files by copying them to
the MMC. Since the MMC is removable (like a floppy disk or a cassette
tape), you can store these GPS Data Files on a personal computer
equipped with an MMC card reader. (Or store them on a pocketful of
MMCs, if you don't have a computer.) Our MapCreate mapping software
can save, edit or create its own GPS Data Files, which can be copied to the
MMC and then loaded from the MMC into the unit's memory. (NOTE: No
matter where they come from, GPS Data Files must be loaded from the
MMC into memory before the GlobalMap can use them.)
The other key GPS use for MMCs is storage of special high-detail, cus-
tom maps, which you can produce on your computer with our MapCre-
ate software. These MapCreate custom maps contain much greater de-
tail than the basic background map. These Custom Map Files (file
format *.lcm) can also be shared between Lowrance GPS or sonar/GPS
units and personal computers.
This unit automatically reads Custom Map Files directly from the
MMC or SD card. To use a custom map, all you need to do is slide an
MMC containing a map into the GlobalMap 6500 or GlobalMap 7500.
The GlobalMap 6600 and GlobalMap 7600 don't read their mapping
data from memory cards. In those units, the full-detail, ready-to-use
maps are already loaded on the unit's hard drives. All you need to do is
use the menus to select what type of mapping data to display. The
GlobalMap 6600 and 7600 hard drives contain all the data from: Map-
Create Topo, our NauticPaths coastal charts and Fishing Hot Spots
Elite lake fishing maps.
Introduction to GPS and WAAS
Well, now you know the basics of how the unit does its work. You might
be ready to jump ahead to Section 2, Installation & Accessories, on page
9, so you can mount your GlobalMap and plug in the power. Or you
might want to see how our text formatting makes the manual tutorials
easy to skim. If that's the case, move on to "How to Use This Manual"
on page 7. But, if you want to understand the current state of satellite
navigation, look over this segment describing how GPS and its new
4
Download from Www.Somanuals.com. All Manuals Search And Download.
companion WAAS work together to get you where you're going.
The Global Positioning System (GPS) was launched July 17, 1995 by
the United States Department of Defense. It was designed as a 24-
hour-a-day, 365-days-a-year, all weather global navigation system for
the armed forces of the U.S. and its allies. Civilian use was also avail-
able at first, but it was less accurate because the military scrambled
the signal somewhat, using a process called Selective Availability (SA).
GPS proved so useful for civilian navigation the federal government
discontinued SA on May 2, 2000, after the military developed other
methods to deny GPS service to enemy forces. Reliable accuracy for ci-
vilian users jumped from 100 meters (330 feet) under SA to the present
level of 10 to 20 meters (about 30 to 60 feet.)
A minimum of three satellites are required to determine a 2D fix.
Twenty-four satellites orbit 10,900 nautical miles above the Earth,
passing overhead twice daily. A series of ground stations (with precisely
surveyed locations) controls the satellites and monitors their exact loca-
tions in the sky. Each satellite broadcasts a low-power signal that iden-
tifies the satellite and its position above the earth. Three of these sat-
ellites are spares, unused until needed. The rest virtually guarantee
that at least four satellites are in view nearly anywhere on Earth at all
times.
The system requires signal reception from three satellites in order to
determine a position. This is called a 2D fix. It takes four satellites to
determine both position and elevation (your height above sea level —
also called altitude). This is called a 3D fix.
Remember, the unit must have a clear view of the satellites in order to
receive their signals. Unlike radio or television signals, GPS works at
very high frequencies. These signals can be easily blocked by trees,
buildings, an automobile roof, even your body.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Like most GPS receivers, this unit doesn’t have a compass or any other
navigation aid built inside. It relies solely on the signals from the sat-
ellites to calculate a position. Speed, direction of travel, and distance
are all calculated from position information. Therefore, in order for the
GlobalMap to determine direction of travel, you must be moving and
the faster, the better. This is not to say that it won’t work at walking or
trolling speeds — it will. There will simply be more "wandering" of the
data shown on the display.
GPS is plenty accurate for route navigation, but the U.S. Federal Avia-
tion Administration has special needs for aircraft traffic control that go
beyond basic GPS. The FAA has a plan under way to boost GPS per-
formance even further with its Wide Area Augmentation System, or
WAAS. This GPS add-on will include a time control element that will
help airliners fly closer together while avoiding collisions. In addition to
carefully spacing airplanes along travel corridors, WAAS will eventu-
ally make instrument landings and takeoffs more accurate as it re-
places existing aviation navigation systems.
Non-aviators can use WAAS signals to make their GPS navigation even
more accurate. Your unit receives both GPS and WAAS signals. How-
ever, WAAS has some limits you should know about.
First, the U.S. government has not completed construction of the WAAS
system, so it is not yet fully operational. The ground stations are in
place, but only a few of the needed WAAS satellites have been launched.
WAAS can boost the accuracy of land GPS navigation, but the system is
designed for aircraft. The satellites are in a fixed orbit around the
Equator, so they appear very low in the sky to someone on the ground
in North America. Aircraft and vessels on open water can get consis-
tently good WAAS reception, but terrain, foliage or even large man-made
structures frequently block the WAAS signal from ground receivers.
You'll find that using your GPS receiver is both easy and amazingly
accurate. It’s easily the most accurate method of electronic navigation
available to the general public today. Remember, however, that this
receiver is only a tool. Always have another method of navigation avail-
able, such as a map or chart and a compass.
Also remember that this unit will always show navigation information
in the shortest line from your present position to a waypoint, regardless
of terrain! It only calculates position, it can’t know what’s between you
and your destination, for example. It’s up to you to safely navigate
around obstacles, no matter how you’re using this product.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use this manual: typographical conventions
Many instructions are listed as numbered steps. The keypad and arrow
"keystrokes" appear as boldface type. So, if you're in a real hurry (or
just need a reminder), you can skim the instructions and pick out what
menu command to use by finding the boldface command text. The fol-
lowing paragraphs explain how to interpret the text formatting for
those commands and other instructions:
Arrow Keys
The arrow keys control the movement of dotted cross-hair lines on your
mapping screen called the cursor. The arrow keys help you move
around the menus so you can execute different commands. They are
represented by symbols like these, which denote the down arrow key,
the up arrow, the left arrow and the right arrow: ↓ ↑ ← →.
Keyboard
The other keys perform a variety of functions. When the text refers to a
key to press, the key is shown in bold, sans serif type. For example, the
"Enter/Icons" key is shown as ENT and the "Menu" key is shown as
MENU.
Menu Commands
A menu command or a menu option will appear in small capital letters,
in a bold sans serif type like this: ROUTE PLANNING. These indicate that
you are to select this command or option from a menu or take an action
of some kind with the menu item. Text that you may need to enter or
file names you need to select are show in italic type, such as trail name.
Instructions = Menu Sequences
Most functions you perform with this unit are described as a sequence
of key strokes and selecting menu commands. We've written them in a
condensed manner for quick and easy reading.
For example, instructions for navigating a trail would look like this:
1. From the Map Page, press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to Trail 1|ENT|→|↓ to NAVIGATE|ENT.
3. You are asked to wait while it converts the trail into a route.
4. The wait message disappears and the GlobalMap begins
showing navigation information along the trail. Now, begin
moving and follow your GlobalMap.
Translated into complete English, step 1 above would mean: "Start on
the Map Page. Press the Menu key twice. Next, repeatedly press (or
7
Download from Www.Somanuals.com. All Manuals Search And Download.
press and hold) the down arrow key to scroll down the menu and select
(highlight) the My Trails menu command. Finally, press the Enter key."
Step 2 would mean: "Press the down arrow key repeatedly to scroll to
the trail named Trail 1, and press Enter. Next, press the right arrow
key and then the down arrow key to highlight the Navigate command,
then press Enter."
NOTE
There are slight differences in menu structure among the Global-
Map models covered in this manual. The differences are minimal,
but some of the screenshots in this manual may not perfectly match
some of your unit's menus.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2:
Installation & Accessories
Preparations
You can install the GPS system in some other order if you prefer, but
we recommend this installation sequence:
Caution:
You should read over this entire installation section before drill-
ing any holes in your vehicle or vessel!
1. Determine the approximate location for the GPS unit, so you can
plan how and where to route the cables for the antenna and power.
This will help you make sure you have enough cable length for the de-
sired configuration.
2. Determine the approximate location for the GPS antenna module
and its cable route.
3. Determine the location of your battery or other power connection,
along with the power cable route.
4. Install the GPS antenna and route the antenna cable to the GPS
unit.
5. Install the power cable and route it to the GPS unit.
6. Mount the GPS unit.
GPS Antenna/Receiver Module
The unit packages covered in this manual include the LGC-2000 GPS
module. This device contains the unit's external antenna and receiver
for GPS and WAAS signals. The antenna/receiver module comes with a
25-foot Y-adapter extension cable. This module can be mounted on a
flat surface or pole, or an optional magnet is available for temporary
mounting on any ferrous surface.
LGC-2000 Module, bottom view (left) and top view (right).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
You need to select an antenna installation location that has a clear, un-
obstructed view of the sky. After the module is installed, connect it to the
unit. The LGC-2000 can communicate with your GPS unit either directly
(using the supplied extension cable) or through a NMEA 2000 network.
NOTE
See the module’s instruction sheet, publication part number 988-
0147-981, for complete installation instructions.
In an automobile, you may achieve good results by simply placing the
external antenna on the top of the dash, at the base of the windshield. A
piece of the rubber non-skid shelf liner material available in recreational
vehicle supply stores will help hold the antenna in place. This may not
work well if you have a cab-over design pickup truck camper or motor
home. If dashboard reception is poor, simply relocate the antenna mod-
ule elsewhere on the vehicle for a clearer view of the sky.
Connecting Directly to the Unit
After the module is installed, attach it to the end of the Y-adapter ex-
tension cable as shown in the following diagram. To connect it to the
unit, insert the extension cable's splitter plug into the Network socket
on the back of the unit and your system is ready to use.
60-ohm
Splitter plug
terminator
LGC-2000
To unit
25' Y-adapter
extension cable
LGC-2000 direct connection to GPS unit.
NOTE:
The extension cable’s shorter branch will have a 60-ohm terminator at-
tached to it. Do not remove this terminator. When you're not con-
necting to a NMEA 2000 buss, you must leave the terminator con-
nected to this socket for your antenna/receiver to function correctly.
Connecting to a NMEA 2000 Network
The LGC-2000 can be connected to a NMEA 2000 buss, providing GPS
information to any Lowrance GPS units attached to the buss. Contact LEI
Extras (look inside back cover for accessory ordering information) for a
NMEA 2000 buss adapter cable if you would like to do this.
There are two ways to connect the antenna to a NMEA 2000 network
port. One method (shown in the following image) is to use the extension
cable's Y-adapter to connect both the antenna and the unit to the same
network port. To do this, simply remove the 60-ohm terminator shown in
10
Download from Www.Somanuals.com. All Manuals Search And Download.
the previous image and attach the NMEA 2000 buss adapter cable to the
shorter branch of the extension cable's Y-adapter. Connect the NMEA
2000 buss adapter cable's other end to an available network port.
To unit
LGC-2000
25' Y-adapter
extension cable
To NMEA 2000
network port
LGC-2000 and GPS unit connection to NMEA 2000 buss.
You can also attach the antenna to a remote port on the network, and
pass position information along the network. To do this, simply attach the
LGC-2000's connector to one end of the buss adapter cable and attach the
other to an available port on the NMEA 2000 buss, as shown in the fol-
lowing image. (You will have to use a similar adapter cable to connect the
GPS unit to the NMEA buss as described later in this section.)
To NMEA 2000
network port
LGC-2000
LGC-2000 remote connection to NMEA 2000 buss.
NOTE:
An existing operational NMEA 2000 buss will already have termina-
tors in place and will already be powered. If you're connecting to such a
network, you won't need the terminators or extension cable provided.
Do not add terminators or power to a functional NMEA 2000 buss!
When the LGC-2000 is connected to the unit (directly or indirectly), it
will begin providing GPS signal information.
Power Connections
Your unit comes with a power/data cable that splits into three ends,
each with several exposed wires (shown in the following figure). The
end with 4 wires (blue, yellow, orange and shield) is a Data cable that
connects to a NMEA 0183 interface. The end with three wires (red,
black and shield) is a power cable that connects to a NMEA-2000 buss.
The thicker three-wire cable (red, black and white) is the Power Supply
for your unit (and optional external speaker connection for some units).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Supply wires:
red, black and white
To unit
NMEA-2000 Power wires:
red, black and shield
Data Cable wires: blue,
yellow, orange and shield
The Power/Data cable for this unit.
Depending on your configuration, you may not use all of these wires.
The following segments include instructions for installing all the wires
that you will use with this unit.
CAUTION:
All of the wires in the power/data cable have bare ends for easier
installation. The bare ends on any unused wires could cause an
electrical short if left exposed. To prevent this, you should cover the
individual wire ends — either by capping them with wire nuts or
wrapping them with electrical tape. (You should cut off the bare
wire before taping off the ends.)
Powering a NMEA-2000 Buss
(NMEA-2000 Power cable)
A NMEA-2000 buss must be connected to a power source to operate. If
you have a pre-existing NMEA-2000 installation, it may already be
connected to another power source. If your NMEA-2000 buss is already
powered, you can ignore the NMEA-2000 Power cable. Never attach
two power sources to a single NMEA-2000 buss.
If you do need to power your NMEA-2000 buss, attach the NMEA-2000
Power cable to your boat's battery just as indicated in the following
segment for connecting your unit's Power Supply cable. The NMEA-
2000 Power cable's red wire should be attached (with provided 3-amp
fuse) to the boat battery's positive terminal, and the NMEA-2000 Power
cable's black and shield wires should both be attached to the battery's
negative terminal.
NOTE:
If the NMEA-2000 buss draws power directly from the boat's battery,
the LGC-2000 will remain on (drawing power) all the time. The LGC-
2000's current draw is very small and shouldn't decrease the boat's
storage battery life, but if this small draw is a concern, you can in-
stall a switch between the NMEA-2000 buss and the battery.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering Your Unit
(Power Supply cable – red and black wires)
The unit works from a 12-volt battery system. For the best results, at-
tach the power cable directly to the battery. You can attach the power
cable to an accessory or power buss, however you may have problems
with electrical interference. Therefore, it's safer to go ahead and attach
the power cable directly to the battery.
CAUTION:
When using the unit in a saltwater environment, we strongly rec-
ommend that you shut off the power supply to the power cable when
the unit is not in use. When the unit is turned off but still connected
to a power supply, electrolysis can occur in the power cable plug.
This may result in corrosion of the plug body along with the electri-
cal contacts in the cable and the unit's power socket.
In saltwater environments we recommend you connect the power
cable to the auxiliary power switch included in most boat designs.
If that results in electrical interference, or if such a switch is not
available, we recommend connecting direct to the battery and in-
stalling an inline switch. This will let you shut off power to the
power cable when the unit is not in use. When you are not using
the unit, you should always shut off power to the power cable, es-
pecially when the power cable is disconnected from the unit.
If possible, keep the power cable away from other boat wiring, especially
the engine's wires. This will provide the best isolation from electrical
noise. If the cable is not long enough, splice #18 gauge wire onto it. The
power cable has two wires, red and black. Red is the positive lead, black
is negative or ground. (There is also a white wire to power an optional
external speaker for some units.) Make sure to attach the in-line fuse
holder to the red lead as close to the power source as possible.
For example, if you have to extend the power cable to the battery or
power buss, attach one end of the fuse holder directly to the battery or
power buss. This will protect both the unit and the power cable in the
event of a short. It uses a 3-amp fuse.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To unit
Optional power off
switch for saltwater
installations
NMEA 0183
Data cable
(four wires)
Unit power
Red wire with
3 amp fuse
supply cable
Black wire
To power a
NMEA-2000
buss, also
connect
NMEA-2000
Power cable
to the boat's
battery.
White speaker wire
12 volt
battery
NMEA 2000
Power cable
Speaker
Black speaker wire
Power and optional speaker connections for the GlobalMap units cov-
ered in this manual.
NOTE:
If you're powering a NMEA 2000 buss, you will attach both the
NMEA 2000 Power cable and the unit's Power Supply cable to the
boat's battery. You must also attach both the power cables to the
battery when you are only connecting the GPS module to the unit
with the Y-adapter cable. To attach the NMEA 2000 Power cable,
connect the red wire to battery's + and black and shield wires to
battery's –.
WARNING:
This product must be independently fused with the en-
closed 3-amp fuse (or equivalent), even if you connect to
a fused accessory or power buss.
If a malfunction happens inside the unit, extensive dam-
age can occur if the enclosed fuse is not used. As with all
electrical devices, this unit could be damaged to a point
that it is unrepairable and could even cause harm to the
user when not properly fused.
CAUTION:
Do not use this product without a 3-amp fuse wired into the power
cable! Failure to use a 3-amp fuse will void your warranty.
This unit has reverse polarity protection. No damage will occur if the
power wires are reversed. However, the unit will not work until the
wires are attached correctly.
External Speaker
Your unit can play sounds to an external speaker. This feature can be
convenient any time you are away from the unit — especially in a
14
Download from Www.Somanuals.com. All Manuals Search And Download.
larger boat — but still want to hear its alarms. You might install a
small speaker at the stern of your boat so you won't miss a dangerous
Shallow Alarm while fishing, or put one in your galley so you can hear
the GPS Arrival Alarm.
You can purchase an external speaker and the wire to connect it at
your nearest audio or marine electronics store. You will need to buy
marine-grade 18 gauge stranded wire. Buy enough of one color (we sug-
gest white) to run from the unit's Power/Data cable to the speaker. Buy
enough of another color (we suggest black) to run from the speaker to
the battery or fuse box.
The unit is designed to work with most speakers, but make sure you
buy one that meets these minimum requirements:
•
•
Minimum 8-ohm resistance
Minimum 5-watt power
In your vessel or vehicle, mount the speaker wherever you want to hear
your unit's sounds. (Follow the speaker's installation instructions).
Next, connect the speaker to your unit as shown in the preceding fig-
ure.
The speaker should have either two terminals or two exposed wires: a
positive (+) and a negative (–) ground. Your unit's external audio out-
put is the white wire in the unit power supply cable. Connect this wire
to the speaker's positive (+) wire or terminal with white 18 gauge wire.
Connect the speaker's negative (–) ground wire or terminal to the nega-
tive (–) terminal on your battery or fuse box with black 18 gauge wire.
The unit should automatically begin to play any active sounds through
the attached speaker.
NMEA 2000 Cable Connections
NMEA 2000 is a new buss network specifically designed for boats. This is
a very young industry standard and, at the time of printing, a few boats
being built now have a NMEA 2000 buss installed. Over the next few
years, however, NMEA 2000 will become much more common. To help
you get the most out of this technology, your Lowrance unit is designed
to work with a NMEA 2000 network as soon as it becomes available.
Connecting to a NMEA 2000 Network
Your unit can be connected to a NMEA 2000 buss, receiving sensor infor-
mation from any Lowrance units attached to the buss. Contact LEI Extras
(look inside back cover for accessory ordering information) for a NMEA
2000 buss adapter cable if you would like to do this. You can connect both
the unit and antenna module through the antenna's extension cable (as
described earlier), or you can connect the unit directly to a network port.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
To do so, attach the adapter cable's manual locking collar connector to the
Network port on the back of the GPS unit and attach the other end to an
available port on the NMEA 2000 buss, as shown in the following figure.
To NMEA 2000
network port
To unit's
Network
socket
Lowrance unit direct connection to NMEA 2000 buss.
As soon as the unit is connected to the network, it will begin receiving
shared information. Please note the buss must be powered to operate. (See
instructions in this section for more on powering NMEA 2000 buss.)
NMEA 0183 Cable Connections
NMEA 0183 is a standard communications format for marine electronic
equipment. For example, an autopilot can connect to the NMEA inter-
face on the GlobalMap 5500C/4900M and receive positioning informa-
tion. The GlobalMap can exchange information with any device that
transmits or receives NMEA 0183 data.
See the following diagram for general wiring connections. Read your
other product’s owner’s manual for more wiring information.
NMEA 0183 Wiring Diagrams
(Data cable)
To exchange NMEA 0183 data, this unit has one NMEA 0183 version
2.0 communication port. Com port one (Com-1) can be used to receive
NMEA format GPS data. The com port can also transmit NMEA format
GPS data to another device.
The four wires for the com port are combined with the Power Supply cable
and NMEA 2000 Power cable to form the power/data cable (shown earlier).
Com-1 uses the yellow wire to transmit, the orange wire to receive and the
shield wire for signal ground. Your unit does not use the blue wire.
Orange (Receive)
NMEA Transmit
To Other
GPS Receiver
Com-1
To unit
Shield (Ground)
Ground
Com-1 wiring to receive NMEA position information
from some other GPS receiver.
NMEA Receive
Ground
Yellow (Transmit)
Shield (Ground)
Com-1
To unit
To Other
Device
Com-1 wiring to transmit NMEA position information
to another NMEA-compatible device.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Network
Power/Data
25' Y-adapter
extension cable
NMEA 0183
Data cable
(four wires)
60-ohm
terminator
Power
Supply
wires
NMEA 2000
Power cable
LGC 2000
GPS Module
Cable connections, GlobalMap 6500 and GlobalMap 6600.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Power/Data
Network
25' Y-adapter
extension cable
NMEA 0183
Data cable
(four wires)
60-ohm
terminator
Power
Supply
wires
NMEA 2000
Power cable
LGC 2000
GPS Module
Cable connections, GlobalMap 7500 and GlobalMap 7600.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Unit: Bracket, In-Dash or Portable
You can install the GlobalMap on the top of a dash with the supplied
gimbal bracket. The GlobalMap 6500 and GlobalMap 6600 can also be
installed in the dash or mounted on a portable power supply.
If you use the supplied bracket, you may be interested in the optional
R-A-M bracket mounting system. This converts the unit's gimbal
bracket to a swivel mount, which can be used on the dash or overhead
mounting positions. Installation instructions are supplied with the
R-A-M mounting kits. R-A-M offers permanent mounts and temporary
mounts suitable for many vehicle types. See your Eagle dealer or visit
the LEI web site (www.lei-extras.com) for the latest options; accessory
ordering information is on the inside back cover of this manual. For
a complete look at the many mounting options, visit the RAM web site
at www.ram-mount.com.
Optional R-A-M mounting system.
Bracket Installation
Mount the GlobalMap in any convenient location, provided there is clear-
ance behind the unit when it's tilted for the best viewing angle. You should
also make sure there is enough room behind the GlobalMap to attach the
power and GPS antenna/receiver module cables. (Drawings beginning on
the next page shows the dimensions of the gimbal-mounted GlobalMaps.)
Holes in the bracket's base allow wood screw or through-bolt mounting.
You may need to place a piece of plywood on the back side of thin fiber-
glass panels to reinforce the panel and secure the mounting hardware.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable hole
Screw
mounting
hole
Front
Install the gimbal bracket. Place the bracket so the arms slope toward
the front of your unit.
Once a location is determined, use the bracket as a template and mark
the mounting holes and the hole for the cables. Drill a 1-inch (25.4 mm)
hole in the dash for the power, transducer and antenna cables. Screw
the bracket to the mounting surface.
Millimeter
[Inch]
Front view (left) and side view (right) showing dimensions of the
GlobalMap 6500 and GlobalMap 6600 mounted on gimbal brackets.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Millimeter
[Inch]
Front view (left) and side view (right) showing dimensions of the
GlobalMap 7500 and GlobalMap 7600 mounted on gimbal brackets.
To pass all connectors through the 1" hole, first pass the antenna con-
nector up through the hole from under the dash. Next, pass the power
cable's bare-wire end down though the hole from the top.
If you wish, you can fill in the hole around the cables with a good ma-
rine caulking compound. No matter what type of installation you pre-
fer, be sure to leave enough slack in the cables to allow tilting or swiv-
eling the unit.
Attach the unit to the gimbal bracket using the supplied gimbal knobs
and washers. Attach the cables and the unit is ready to use.
In-Dash Installation
You can mount the GlobalMap 6500 and GlobalMap 6600 in the dash
with an optional FM-3 In-Dash Adapter Kit. The kit includes mounting
hardware and a template for cutting the hole.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
In-dash mounting template for the GlobalMap 6500 and GlobalMap
6600, showing dimensions. The figure above is not printed to scale.
Portable Installation
Like many Lowrance products, the GlobalMap 6500 and GlobalMap
6600 are capable of portable operation by using an optional portable
power pack. The power pack and the magnet-equipped antenna module
expand the uses for your GPS unit. The portable power pack makes it
easy to transfer your unit from a boat to a car, recreational vehicle, air-
plane or other vehicle without drilling and mounting a second bracket.
You can use your unit in your own car or boat, then take it along when
riding in a friend's vehicle that's not equipped with GPS.
The portable power pack includes a sealed, rechargeable battery.
MMC or SD Memory Card Installation
Your unit uses MultiMedia Cards to store information, such as custom
maps, waypoints, trails and other GPS data. The unit can also use Se-
cure Digital Cards (SD card) to store data. These units can use up to
two cards; an MMC and an SD card can be used at the same time.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
Throughout this manual, we will use the term MMC, but just re-
member your unit can use an MMC or SDC to store data.
Both of these solid-state flash memory devices are about the size of a
postage stamp. A SD card is slightly thicker than a MMC. MMCs are
available in storage capacities of 8 MB, 16 MB, 32 MB, 64 MB and
higher. SD cards are available in capacities of 8 MB, 16 MB, 32 MB, 64
MB, 128 MB, 256 MB and 1 GB.
Additional MMC cards are available from LEI Extras; see ordering in-
formation inside the back cover of this manual. MMCs and SD cards
are also available at many camera and consumer electronics stores.
In the GlobalMap 6500 and GlobalMap 6600, the MMC drawer is lo-
cated on the front of the case. To install an MMC, twist the drawer re-
tainer counter-clockwise and pull. The drawer will come out of the unit.
Place the MMC in the drawer face down (see following figures.)
Insert cards face down
Drawer
retainer
Memory card drawer on the GlobalMap 6500 and GlobalMap 6600.
Slide the drawer back into the unit and twist the retainer clockwise.
The MMC is now ready for use.
In the GlobalMap 7500 and GlobalMap 7600, the two MMC slots are
located in compartments on the front of the case. The water-proof com-
partment doors are located at the lower right corner. The following fig-
ure shows a close-up of one compartment with the door opened.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MMC groove for card removal
Thumb
screw
Insert card face up,
this way
Memory card compartment with a 16 MB MMC card installed.
To remove an MMC or SD Card
1. Open the card compartment door by unscrewing the thumb screw.
The screw should only be finger tight. If it was over-tightened, use a
thumbnail, a coin or a screwdriver to open the door.
2. Use the ball of your finger or thumb and press down in the center of
the card, then drag the MMC from the slot. Or, use a thumbnail or fin-
gernail to grab the groove in the bottom of the MMC and drag it out.
See the figure above for the groove location.
To add an MMC or SD Card
1. Open the card compartment door.
2. Grasp the bottom of the MMC and push the top of the card into the
slot. Once the card is started, press down in the center of the card with
the ball of your finger or thumb and push the card all the way to the
left, until it is firmly seated in the slot.
3. Close the compartment door and fasten the thumb screw finger tight.
Other Accessories
Other accessories include MMC cards, MMC card readers and MapCre-
ate™ 6 custom mapping software for your computer. MMC card readers
are available in USB versions.
If these accessories are not available from your dealer, see the acces-
sory ordering information on the inside back cover of this manual.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
MapCreate™ 6 CD-ROM, left; MMC card reader for USB ports, right.
Now that you have your GlobalMap installed, move on to Section 3, Ba-
sic GPS Operations. There, we'll present a series of step-by-step tutori-
als to teach you the basics of GPS navigation.
Face Cover
Your unit comes with a white protective cover that snaps on and off the
front of the unit. This cover is intended for use when your unit and the
vehicle it's mounted in are idle.
WARNING:
When the unit is mounted in an unprotected area, such
as an open boat cockpit, the protective face cover must
be removed when the vehicle is moving at high speed.
This includes towing a boat on a trailer at highway
speeds. Otherwise, wind blast can pop off the cover.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3:
Basic GPS Operations
This section addresses the unit's most basic GPS operations. The tuto-
rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced
GPS Operations, will discuss other more advanced functions and utili-
ties. Material in Sec. 4 is arranged in alphabetical order.
Before you turn on the unit and find where you are, it's a good idea to
learn about the different keys, the three Page screens and how they all
work together. BUT, if you just can't wait to get outside, turn to the
one-page Quick Reference on page 39.
NOTE
There are slight differences in menu structure among the Global-
Map models covered in this manual. The differences are minimal,
but some of the screenshots in this manual may not perfectly match
some of your unit's menus.
Keyboard
4
8
2
3
5
9
7
6
1
MMC drawers
GlobalMap 7600CHD GPS unit, front view, showing screen,
keyboard and MMC drawers.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
1. PWR/LIGHT (Power & Light) – The PWR key turns the unit on and
off and activates the backlight.
2. PAGES – Pressing this and the ← → arrow keys (4) switches the
unit between the three different page screens. (Satellite Status Page,
Navigation Page and Map Page.) Each page represents one of the unit's
major operation modes.
3. MENU – Press this key to show the menus and submenus, which
allow you to select a command or adjust a feature. This also accesses
search functions for streets, intersections, addresses and highway exits.
4. ARROW KEYS – These keys are used to navigate through the
menus, make menu selections, move the map cursor and enter data.
5. ENT/ICONS (Enter & Icons) – This key allows you to save data, ac-
cept values or execute menu commands. It is also used to create event
marker icons.
6. EXIT – The Exit key lets you return to the previous screen, clear
data or close a menu.
7. WPT – (Waypoint) The Waypoint key is used to save and recall way-
points, search for waypoints and access the waypoint list. It also
launches the Point-of-Interest (POI) search menus and is involved in
some navigation functions.
8. ZOUT – (Zoom Out) – This key lets you zoom the screen out. On the
Map Page, this lets you see a larger geographic area on the map. Less
detail is seen as you zoom out.
9. ZIN – (Zoom In) – This key lets you zoom the screen in. On the Map
Page, zooming in lets you see greater detail in a smaller geographic
area on the map.
Power/lights on and off
To turn on the unit, press PWR. As the unit powers up, the Map Page is
displayed first. (To switch to another page, press PAGES|← or → to
Page Name|EXIT.)
To turn on the backlight, press PWR again. The unit has three backlight
levels to select from. Repeatedly pressing PWR will cycle through the
backlight settings and turn off the backlight.
Turn off the unit by pressing and holding the PWR key for 3 seconds.
Main Menu
The GlobalMap has a Main Menu, which contains some function com-
mands and some setup option commands. The tutorial lessons in this
section will deal only with functions, the basic commands that make
28
Download from Www.Somanuals.com. All Manuals Search And Download.
the unit do something. The unit will work fine for these lessons right
out of the box with the factory default settings. But, if you want to
learn about the various options, see Sec. 5, System Setup and GPS
Setup Options.
You can access the Main Menu from any of the three Page screens by
pressing MENU|MENU. To clear the menu screen and return to the page
display, press EXIT.
Main Menu.
The Main Menu commands and their functions are:
Screen command: changes the contrast or brightness of the screen.
Sounds command: enables or disables the sounds for key strokes and
alarms and sets the alarm style.
Transparency command: adjusts the level of transparency for menus
(Not available in some models).
Alarms command: turns GPS alarms on or off and changes alarm
thresholds.
Route Planning command: used to plan, view or navigate a route.
My Trails command: shows, hides, creates and deletes plot trails. Also
used to navigate or backtrack a trail.
Cancel Navigation command: turns off the various navigation com-
mands. Used to stop navigating after you have reached your destina-
tion waypoint, Point of Interest or map cursor location; or after you
reach the end of a route or trail.
GPS Setup command: sets various GPS receiver options.
System Setup command: sets general configuration options.
Sun/Moon Calculations command: finds the rising and setting time
of the sun and the moon.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Trip Calculator command: shows trip status and statistics.
Timers command: controls the up timer, down timer and alarm clock
settings.
Browse MMC Files command: this allows you to view the installed
MMC card and the files it contains.
Pages
The unit has three Page displays that represent the three major operat-
ing modes. They are the Satellite Status Page, the Navigation Page and
the Map Page. They are accessed by pressing the PAGES key, then using
→ or ← to select a Page. (Clear the Pages Menu by pressing EXIT.)
Pages Menu showing some Map display options.
Satellite Status Page
The Satellite Status Page, shown, provides detailed information on the
status of the GlobalMap's satellite lock-on and position acquisition. To
get to the Satellite Status Page: Press the PAGES key, then use → or ←
to select STATUS. (Clear the Pages Menu by pressing EXIT.)
No matter what Page you are on, a flashing current position indica-
tor/question mark symbol and flashing GPS data displays indicate that
satellite lock has been lost and there is no position confirmed. The Sat-
ellite Status Page shows you the quality and accuracy of the current
satellite lock-on and position calculation.
WARNING:
Do not begin navigating with this unit until the numbers
have stopped flashing!
30
Download from Www.Somanuals.com. All Manuals Search And Download.
The Satellite Status Page.
This screen shows a graphical view of the satellites that are in view. Each
satellite is shown on the circular chart relative to your position. The point in
the center of the chart is directly overhead. The small inner ring represents
45° above the horizon and the large ring represents the horizon. North is at
the top of the screen. You can use this to see which satellites are obstructed
by obstacles in your immediate area if the unit is facing north.
The GPS receiver is tracking satellites that are in bold type. The re-
ceiver hasn't locked onto a satellite if the number is grayed out, there-
fore it isn't being used to solve the position.
Beneath the circular graph are the bar graphs, one for each satellite in
view. Since the unit has twelve channels, it can dedicate one channel
per visible satellite. The taller the bar on the graph, the better the unit
is receiving the signals from the satellite.
The "Estimated Position Error" (horizontal position error) shown in the
upper left corner of the screen is the expected error from a benchmark
location. In other words, if the EPE shows 50 feet, then the position
shown by the unit is estimated to be within 50 feet of the actual loca-
tion. This also gives you an indicator of the fix quality the unit cur-
rently has. The smaller the position error number, the better (and more
accurate) the fix is. If the position error flashes dashes, then the unit
hasn't locked onto the satellites, and the number shown isn't valid.
The Satellite Status Page has its own menu, which is used for setting
various options. (Options and setup are discussed in Sec. 5.) To access
the Satellite Status Page Menu, from the Status Page, press MENU.
Navigation Page
This screen has a compass rose that not only shows your direction of
travel, but also the direction to a recalled waypoint. To get to the Navi-
gation Page: Press PAGES| → or ← to NAVIGATION|EXIT.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
The navigation screen looks like the one below when you're not navi-
gating to a waypoint or following a route or trail. Your position is
shown by an arrow in the center of the screen. Your trail history, or
path you've just taken, is depicted by the line extending from the arrow.
The arrow pointing down at the top of the compass rose indicates the cur-
rent track (direction of travel) you are taking.
Track or compass heading indicator, showing direction of travel
Navigation
information
displays
Compass
rose
Present
position
arrow
Trail line
The GlobalMap navigation Page, recording a trail, traveling east. Page
looks like this when the unit is not navigating to a waypoint, following
a route, or backtracking a trail.
When navigating to a waypoint, the Navigation screen looks like the
following figure. Your ground speed, track, distance and bearing to
waypoint, and course are all shown digitally on this screen.
NOTE:
Remember, when the Speed, Track and Position information dis-
plays are flashing, satellite lock has not been achieved and no posi-
tion fix has been determined. A question mark will also flash on the
position arrow in the center of the compass rose.
Speed (ground speed) is the velocity you are making over the ground. (If
you wish, you can customize the Speed window to display Closing
Speed instead. Closing Speed is also known as velocity made good. It's
the speed that you're making toward the waypoint. For instructions,
see the Customize Page Displays entry in Sec. 5.)
Track is the heading, or the current direction you are actually travel-
ing. Bearing is the direction of a line-of-sight from your present position
to the destination. No matter what direction you are steering, the
Bearing window shows the compass direction straight to the destina-
32
Download from Www.Somanuals.com. All Manuals Search And Download.
tion from your location at the moment. Distance shows how far it is to
the waypoint you're navigating toward.
The Off Course window shows the current cross track error. This shows
the distance you are off-course to the side of the desired course line. The
course line is an imaginary line drawn from your position when you
started navigating to the destination waypoint. The course line is shown on
the Navigation Page screen (and the Map Page screen) as a dotted line.
The cross track error range is shown on the compass rose as a wide,
white, corridor enclosing the course line. The outer edges of this white
corridor represent lines that show the current cross track error range.
The default for the cross track error range is 0.20 miles.
For example, if the present position symbol touches the right cross
track error line, then you are 0.20 miles to the right of the desired
course. You need to steer left to return to the desired course. You can
use the ZIN or ZOUT keys to change the cross track error range.
A circular symbol depicting your destination (waypoint) appears on the
screen as you approach the waypoint, as shown on the screen in the
following figure.
Travel Time is the time that it will take to reach your destination at
your present closing speed. (You can also customize the time window to
show Arrival Time instead. Arrival Time is the local time it will be
when you arrive at the destination, based upon your present closing
speed and track.)
Trail line Course line
Current track
or heading,
shown
in degrees
Bearing
arrow
Compass
bearing to
destination
Waypoint
symbol
Cross track
error range
(off course
indicator)
Left cross
track error line
Navigation
information
displays
Destination
name
The GlobalMap navigation page, backtracking a trail while
creating a new trail.
In the example above, the driver is headed north (a 355º track) toward
a waypoint 355º (bearing) away. The cross track error range (white cor-
33
Download from Www.Somanuals.com. All Manuals Search And Download.
ridor) is 0.20 miles either side of the course. The driver is headed to-
ward trail waypoint 4, which is 0.14 miles away. The vehicle is virtually
on course (off course 1 foot to the right). Traveling at a speed of 27 mph,
the driver will arrive at the waypoint in 19 seconds.
The Navigation Page has its own menu, which is used for some ad-
vanced functions and for setting various options. (Options and setup
are discussed in Sec. 5.) To access the Navigation Page Menu, from the
Navigation Page, press MENU.
Map Page
The Map Page screens show your course and track from a "bird's-eye"
view. By default, this unit shows the map with north always at the top
of the screen. (This can be changed. See the topic Map Orientation, in
Sec. 5.) If you're navigating to a waypoint, the map also shows your
starting location, present position, course line and destination. You
don't have to navigate to a waypoint, however, to use the map.
Map Page is the default screen that appears when you turn on the unit.
To get to the Map Page from another page: Press PAGES| → or ← to
MAP|EXIT. When the Map Page is displayed, a screen similar to the fol-
lowing figures appears.
The arrow in the center of the screen is your present position. It points
in the direction you're traveling. The solid line extending from the back
of the arrow is your plot trail, or path you've taken.
The map zoom range is the distance across the screen. This number
shows in the lower right corner of the screen.
In the first example below, the range is 4,000 miles from the left edge of
the map to the right edge of the map.
The Zoom In and Zoom Out keys zoom the map to enlarge or reduce its
coverage area and the amount of mapping detail shown. There are 37
available map zoom ranges, from 0.05 miles to 4,000 miles.
Map Page opening screen (left). Zoomed to 100 miles (center) and
zoomed to 15 miles (right). Over Zoomed means you have reached the
detail limits in an area covered only by the basic background map.
Zooming in any closer will reveal no more map details because a high-
detail custom map has not been loaded on the MMC.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
If you're using only the factory-loaded background map, the maximum
zoom range for showing additional map detail is 20 miles. You can con-
tinue to zoom in closer, but the map will simply be enlarged without
revealing more map content (except for a few major city streets.) Load
your own high-detail custom map made with MapCreate, and you can
zoom in to 0.05 miles with massive amounts of accurate map detail.
Map Pages with high-detail MapCreate map of an urban area loaded on
the MMC. Arterial streets appear at the 6-mile zoom range with a few
Point of Interest icons visible (left). Numerous dots representing Points
of Interest become visible at the 3-mile range, along with minor streets
(center). At the 0.6-mile zoom, you can see an interstate highway with an
exit, major and minor streets as well as Point of Interest icons (right).
Background map vs. MapCreate map content
GlobalMap HD models contain a hard drive with full map detail built
into the background map (including all of the information available in
MapCreate custom maps). For all other units, the basic background
map includes: low-detail maps of the whole world (containing cities,
major lakes, major rivers, political boundaries); and medium-detail
maps of the United States.
The medium-detail U.S. maps contain: all incorporated cities; shaded
metropolitan areas; county boundaries; shaded public lands (such as
national forests and parks); some major city streets; Interstate, U.S.
and state highways; Interstate highway exits and exit services informa-
tion; large- and medium-sized lakes and streams; and more than 60,000
navigation aids and 10,000 wrecks and obstructions in U.S. coastal and
Great Lakes waters
MapCreate custom maps include massive amounts of information not
found in the background map. MapCreate contains: the searchable
Points of Interest database, all the minor roads and streets, all the
landmark features (such as summits, schools, radio towers, etc.); more
rivers, streams, smaller lakes and ponds and their names.
What's more important is the large scale map detail that allows your
GPS unit to show a higher level of position accuracy. For example, the
background map would show you the general outline and approximate
35
Download from Www.Somanuals.com. All Manuals Search And Download.
shape of a coastline or water body, but the higher detail in MapCreate
shows the shoreline completely and accurately (finer detail). Many
smaller islands would not be included in the background map, but are,
of course, in MapCreate.
POI Pop-up,
with position,
distance and
bearing data
Interstate
Cursor line
Major Street
Minor
Streets
POI
Marker
School POI
Restaurant
POI
Zoom Range
When the map is zoomed out far enough, most POIs appear as square
dots (left). As you zoom in closer, the symbols become readable icons.
In the 0.6-mile zoom example (right), the cursor has selected the Cupps
Café POI, which triggers a pop-up box with the POI name. This pop-up
box works on POIs at any zoom range.
Tip:
In some urban areas, businesses are so close to one another that
their POI icons crowd each other on the screen. You can reduce
screen clutter and make streets and other map features easier to
see by simply turning off the display of POIs you're not watching
for. (To see how, check the text on Map Detail Category Selection,
page 85. It shows how to use the Map Categories Drawn menu to
turn individual POI displays off and on.)
The Map Page has its own menu, which is used for several functions
and for setting various options. To access the Map Page Menu, from the
Map Page, press MENU.
The Pages Menu also offers several map display options under the Map
Page category. To access them, press PAGES|← or→ to MAP|↓ to Op-
tion|EXIT.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
GlobalMap Digital Data page (left) and Two Position Formats page
(right).
Pages Menu with Two Maps option selected (left).
Map Page with two map windows (right). The right map is active.
In pages that have two major windows (such as two maps) you can tog-
gle back and forth between the two windows by pressing
PAGES|PAGES.
This allows you to change which map the cursor, keyboard and menus
operate on. "Active window" will be displayed at the top of the active
window.
Resize Window is another extremely handy feature for pages that have
two major windows. You can change the horizontal size of the windows
to suit your viewing preference. Here's how:
1. From any two-window display, press MENU|↓ to RESIZE WINDOW|ENT.
2. Two flashing arrows appear along the centerline dividing the two
windows. Press ← or → to adjust the window widths. Press EXIT to clear
the menu.
3. To change the window size again or revert back to the original dis-
play, just follow the steps above. (Most dual-window displays use half
37
Download from Www.Somanuals.com. All Manuals Search And Download.
the screen for each window by default.) You can also use the Reset Op-
tions command to revert to the factory default.
Map Menu with Resize Window command selected (left). Resize Win-
dow command is active (center). Pressing the ← → or ↑ ↓ keys allows
you to resize the windows from side to side or stack them one on top of
the other (right).
The following page contains a 12-step quick reference for the most basic
GPS operations. If you don't want to carry the manual with you as you
practice with the unit, you might consider photocopying this quick ref-
erence page and tucking it into your pocket.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS Quick Reference
Start outdoors, with a clear view of the open sky. As you practice, try
navigating to a location at least a few blocks away. While you're learning,
navigation in too small an area will constantly trigger arrival alarms.
1. Connect the unit to electric power and the antenna module. Make sure
the MMC is in. (See complete installation details beginning on page 9.)
2. To turn on the GlobalMap, press and release PWR key.
3. Opening screen displays map of North America at the 4,000-mile
zoom range. Rotate through the three main Page screens (Map Page,
Satellite Status Page and Navigation Page) by pressing PAGES|← or →
to select Page Name|EXIT. Switch Pages to display Satellite Status
Page.
4. Wait while unit locates satellites and calculates current position. Process
is visible on Satellite Page. This takes an average of 1 minute or less under
clear sky conditions (unobstructed by terrain or structures.) When the unit
acquires position, a tone sounds and a position acquired message appears.
5. With position acquired, press PAGES key to display Map Page, which
shows a bird's eye view of the earth. You can move around the map by:
Zoom in closer to see greater detail: press ZIN (zoom in key.)
Zoom out to see more area, less detail: press ZOUT (zoom out key.)
Scroll map north, south, east or west using arrow keys ↑ ↓ → ← .
To stop scrolling and return to current position on map, press EXIT key.
6. Set a waypoint (Wpt 001) at your current position so you can navi-
gate back here: press WPT|WPT. Waypoint symbol and "001" appears.
7. Zoom/scroll map to find a nearby object or location to go to. Use ar-
row keys to center cursor cross-hair over the map object or location.
8. Navigate to the selected destination: press MENU|ENT|EXIT. Follow dot-
ted course line on Map Page or compass bearing arrow on Navigation Page.
9. At destination, Arrival Alarm goes off. To clear it, press EXIT. Cancel
navigation: press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
10. Return to Wpt 1 by Navigate To Waypoint or Backtrack Trail. To
Waypoint: press WPT|→ to SAVED|ENT|ENT|ENT. Use ↑ or ↓ to select
Wpt 001, press ENT|ENT; follow navigation displays. Trail: press
MENU|MENU|↓ to MY TRAILS|ENT. Press ↓ to Trail 1|ENT|→|↓ to
NAVIGATE|ENT|↓ to NAVIGATE|→ to REVERSE|ENT|← to NAVIGATE|ENT. (If
arrival alarm sounds, press EXIT.) Follow navigation displays.
11. Back home, Arrival Alarm goes off; press EXIT. Cancel navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
12. To turn off the unit, press and hold PWR key for three seconds.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Your Current Position
Finding your current position is as simple as turning the GlobalMap on.
With an unobstructed view of the sky, the unit automatically searches
for satellites and calculates its position in approximately one minute or
less.
If for some reason satellite acquisition takes longer, you may be inside
a structure or vehicle or in terrain that is blocking signal reception. To
correct this, be sure you are positioned so that the unit's antenna mod-
ule has as clear a view of the sky as possible, then turn the unit off and
back on again.
Moving Around the Map: Zoom & Cursor Arrow Keys
The map is presented from a bird's eye view perspective. The current
zoom range shows in the lower right corner of the screen.
1. Press the ZIN key (zoom in) to move in closer and see greater detail in
a smaller geographic area.
2. Press the ZOUT key (zoom out) to move farther away and see less map
detail, but a larger geographic area.
When you are traveling, the map will automatically move as you move.
This keeps your current location roughly centered on the screen.
You can manually pan or scroll the map northward, southward, east-
ward or westward by using the arrow keys, which launch the cross-hair
map cursor. This allows you to look at map places other than your cur-
rent position. To clear the cursor, press EXIT, which jumps the map
back to the current position or the last known position.
Tip:
Use the cursor to determine the distance from your current position
(or last known position, when working indoors) to any map object.
Simply use the arrow keys to position the cursor over the object or
landmark. The distance, measured in a straight line, appears in the
pop-up box. Press EXIT to clear the cursor.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
POI pop-up
name box
Cursor line
Distance
measured
by cursor
Selected
airport
Cursor line
The selected airport is 4.25 miles away, to the northwest.
Selecting Any Map Item with the Cursor
1. Use the zoom keys and the arrow keys to move around the map and
find the item you wish to select.
2. Use the arrow keys and center the cursor cross-hair on the desired
object. On most items, a pop-up box will give the name of the selected
item.
Searching
Now that you've seen how the GlobalMap can find where you are, let's
search for something else. Searching is one of the most powerful fea-
tures in the Lowrance GPS product line.
In this example, we'll look for the nearest fast-food restaurant. For more
information on different types of searches, refer to Sec. 6, Searching.
NOTE:
This example requires the Point of Interest (POI) database included
with a high detail MapCreate 6 custom map.
After the unit has acquired a position:
1. Press WPT|↓ to POI-RESTAURANTS.
2. You could search the entire restaurant category, but in this example
we will narrow our search. Press → to SUBCATEGORY column|↓ to FAST
FOOD CHAINS|ENT|↓ to NEAREST|ENT.
3. The unit says it is calculating, then a list of restaurants appears,
with the closest at the top of the list, and the farthest at the bottom of
the list. The nearest is highlighted.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Category Selection menu (left); list of the nearest restaurants (right).
4. If you wish, you could scroll ↑ or ↓ here to select another restaurant,
but for now we will just accept the nearest one. Press ENT.
5. The POI information screen appears. (This is how you can use the
GlobalMap as a business phone directory!) If you wanted to navigate
there, you could press ENT, since the GO TO command is highlighted. But
we just want to see it on the map, so press ↓ to FIND ON MAP|ENT.
The POI information screen shows name, street address, phone num-
ber, latitude/longitude, distance to restaurant and its compass bearing.
The Go To command (left); Find On Map command (right).
6. The unit's map appears, with the cross-hair cursor highlighting the
restaurant's POI symbol. A pop-up name box identifies the POI, as well
as its distance and bearing. A data box at the bottom of the screen con-
tinues to display the location's latitude and longitude.
7. To clear the search and return to the last page displayed, press
EXIT|EXIT|EXIT|EXIT. (Before you completely exited out of the Search
menus, you could have gone looking for another place.)
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Map screen showing Find Waypoint, the result of a restaurant search.
NOTE:
Search works from mapping and POI data loaded in the GlobalMap.
If you do not have a high-detailed custom map (containing POI
data) for the area you are searching loaded on the MMC, you may
not find anything.
Set a Waypoint
A waypoint is simply an electronic "address," based on the latitude and
longitude of a position on the earth. A waypoint represents a location,
spot, or destination that can be stored in memory, then be recalled and
used later on for navigation purposes.
You can create a waypoint at the cursor position on the map, or at your
current position while you are navigating. You can create a waypoint at
any location by manually entering the position's latitude and longitude.
You can copy waypoints from your unit to your personal computer with
MapCreate software. When you want to repeat a trip, these archived
waypoints can be reloaded into your GPS unit.
To create and save a Waypoint
These first two techniques use the Quick Save method, the fastest and
easiest way to create a waypoint.
Create Waypoint at Current Position
While you are traveling, press WPT|WPT. The waypoint is saved and
automatically given a name with a sequential number, such as "way-
point 003." The waypoint symbol and number appear on the map.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1.
Step 2.
Step 4.
Step 3.
Sequence for setting a waypoint. Step 1: while traveling, quickly press
WPT twice to call up Find Waypoint screen (seen in Step 2) and set a
point. Step 3: a message says the waypoint has been saved. Step 4: ve-
hicle continues on its way; number waypoint symbol is visible on map.
NOTE:
The Quick Save method uses the default waypoint symbol until you
edit an existing waypoint and change its symbol. (Edit Waypoint
Symbol is described in Sec. 4.) After you have changed a waypoint
symbol, the unit will remember the one you chose and use it the
next time you "quick save" a waypoint. To revert back to the default
symbol, edit a waypoint and choose it, or use the Reset Options
command (described in Sec. 5).
Create Waypoint on Map
1. Use the arrow keys to move the cursor to the place where you want
to make a waypoint.
2. Press WPT|WPT. The waypoint is saved and automatically given a
name with a sequential number, such as "waypoint 001." The waypoint
symbol and number appear on the map.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Create Waypoint by Entering a Position
1. Press WPT|→ to SUBCATEGORY column|↓ to NEW|ENT.
2. Press ↓ to ENTERED POSITION|ENT|→ to CREATE|ENT.
3. Press → to LATITUDE|ENT. Enter the latitude by pressing ↑ or ↓ to
change the first character, then press → to the next character and re-
peat until the latitude is correct. Press ENT.
4. Press ↓ to LONGITUDE|ENT. Enter the longitude by pressing ↑ or ↓ to
change the first character, then press → to the next character and repeat
until the longitude is correct. Press ENT, then EXIT|EXIT to return to the
previous page display. The waypoint is saved and automatically given a
name with a sequential number, such as "waypoint 001." The waypoint
symbol and number appear on the map and in the waypoint list.
Navigate To a Waypoint
You can select any waypoint visible on the Map Page with the cursor,
then use the Navigate to Cursor command (we'll describe how later in
this section.) You, however, can avoid scrolling the map to pick your
waypoint if you use the Find Waypoint commands:
1. Press WPT|→ to SAVED|ENT. To look up the nearest waypoint, press
↓ to NEAREST|ENT; or, to look by name (and scroll through the entire
waypoint list), press ENT. For this example, look by name.
2. If your waypoint list is a long one, you can spell out the waypoint
name in the FIND BY NAME box to search for it. (Press ↑ or ↓ to change the
first character, then press → to move the cursor to the next character
and repeat until the name is correct, then press ENT to jump to the list
below.)
3. If the list is short, you can jump directly to the FIND IN LIST box by
pressing ENT. Use ↑ or ↓ to select the waypoint name, press ENT and
the waypoint information screen appears with the GO TO command se-
lected.
4. To begin navigating to the waypoint, press ENT.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Waypoint
Course line
(dotted)
Trail line
(solid)
Off course
range, set at
0.20 mile
Destination
name
GlobalMap navigation Page, navigating toward waypoint 004 and leav-
ing a trail.
Set Man Overboard (MOB) Waypoint
One of boating's most terrifying events is having a friend or family
member fall overboard. This situation can be deadly on any body of wa-
ter. It's particularly dangerous at night or if you're out of sight of land.
Of course, the first thing to do is remain calm and then use all standard
safety procedures to rescue the person.
This unit has a man overboard feature that shows navigation data to
the location where the feature was activated. To activate it, press the
ZOUT and ZIN keys at the same time. Your position at the time these
keys are pressed is used as the man overboard position.
Caution:
Saving a new "Man Overboard" waypoint will overwrite and
erase the previous "Man Overboard" waypoint.
Navigate Back to MOB Waypoint
Find your way back to the accident position with the Navigation Page
or Map Page. When MOB is activated, the Navigation Page automati-
cally shows the compass rose with its bearing arrow pointing toward
the man overboard position, and the destination name says "Going To
Man Overboard." The Map Page displays a Man Overboard waypoint,
represented by a human figure, and the steering arrow points where to
steer to reach that position.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigating to Man Overboard: navigation page (left) and Map Page
(right). The victim is astern of the vessel; the GPS shows which direc-
tion to steer to for the rescue.
The man overboard position is also stored in the waypoint list for future
reference. It can be edited the same as any other waypoint.
To cancel navigation to MOB, press MENU|MENU|↓ to CANCEL NAVIGA-
TION|ENT|← to YES|ENT. The GlobalMap stops showing navigation infor-
mation.
Navigate to Cursor Position on Map
The GO TO CURSOR command navigates to the current cursor position on
the map. It's a quick and handy way to navigate to anything you can
see on the map display.
1. Use the cursor (controlled by the arrow keys) with the zoom in and
zoom out keys to maneuver around the map until you find a location
you want to go to.
2. Center the cursor over the location to select it. See the example in
the following figure. (Many map items such as waypoints, Points of In-
terest, towns, etc. can be "selected," and appear "highlighted" with a
pop-up box. Other features, such as a river or a street intersection will
not appear "highlighted," but the cursor will take you to those locations
just the same.)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigate to cursor. In this example, the cursor is positioned on the
town of Oologah, Oklahoma.
3. Press MENU|ENT and the GlobalMap will begin navigating to the
cursor location.
The Map Page will display a dotted line from your current position to the
cursor position. The Navigation Page displays a compass rose showing
navigation information to your destination. See the following examples.
The 30-mile zoom example (left) shows the dotted course line connecting
your current position to your destination. The other 30-mile zoom exam-
ple (center), shows both current position and direction to destination on
screen. The Navigation Page (right) will also show navigation informa-
tion.
To stop navigating to the cursor, use the Cancel Navigation command:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT. The unit
stops showing navigation information.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigate to a Point of Interest
For POIs that are in view on the map, you can easily use the Navigate
to Cursor command above. Just use the cursor to select the POI.
The other method involves searching for POIs with the Find Waypoint
command, launched with the WPT key. (See the searching example ear-
lier in this section, or turn to Sec. 6, Searching, for detailed instructions
on POI searches.)
After you have looked up an item with the Find Waypoint command,
use the → to make sure the GO TO command is highlighted at the top of
the screen, then press ENT. The GlobalMap begins showing navigation
information to the item.
To cancel navigation, press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|←
to YES|ENT. The unit stops showing navigation information.
Creating and Saving a Trail
A trail, or plot trail, is a string of position points plotted by the Global-
Map as you travel. It's a travel history, a record of the path you have
taken. Trails are useful for repeating a journey along the same track.
They are particularly handy when you are trying to retrace your trip
and go back the way you came. On the screen, trails are represented by
a solid line extending from the back of the current position arrow.
The GlobalMap is set at the factory to automatically create and record
a trail while the unit is turned on. The unit will continue recording the
trail until the length reaches the maximum trail point setting (default
is 2,000, but the unit can record trails 9,999 points long). When the
point limit is reached, the unit begins recording the trail over itself.
By default, the trail flashes once a second, making it easier to see
against the background map. With the default auto setting, the
GlobalMap creates a trail by placing a dot (trail point) on the screen
every time you change directions. (The trail update rate and the meth-
ods used for creating a trail can be adjusted or even turned off. See Sec.
5 for Trail Options.)
To preserve a trail from point A to point B, you must "turn off" the trail
by making it inactive before heading to point C or even back to point A.
When the current trail is inactive, the GlobalMap automatically begins
recording a new trail.
To Save a Trail
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to the Saved Trail List|ENT.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Visible
symbol
Active
symbol
Sequence for saving a trail and beginning a new one. My Trails com-
mand (left). The arrow to the right of Trail 17 (center) indicates the
trail is "active" and the check to the left shows the trail is visible on the
map. The Edit Trail menu (right) with Active command selected.
3. Press ↓ → to ACTIVE|ENT. This unchecks the Active option.
4. To return to the previous page, press EXIT|EXIT|EXIT|EXIT. As you
left the Edit Trail menu, you will notice that a new trail was started
with a new sequential number. In the example below, the new trail is
number 15, showing zero points. Note that Trail 14 is inactive, but it is
still visible on the map.
A new trail, Trail 15, is created when Trail 14 is set to inactive. Any
new travel will be recorded on this trail, which is active and visible.
Trails do not need to be visible in order to be active.
You can save and recall up to 10 different plot trails, which can also be
copied to your MMC for archiving or for transfer to your MapCreate
software.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip:
Another quick way to stop recording one trail and begin a new one
is to use the New Trail command: Press MENU|MENU|↓ to MY
TRAILS|ENT|ENT.
Caution:
You also have the option of completely turning off trail record-
ing, under the trail Options command. If, however, the Update
Active Trail option is left turned off, it will cancel the automatic
trail creation feature.
Displaying a Saved Trail
The active trail is automatically displayed on the map (the "Visible"
option) with the factory default settings. You can selectively turn trail
display off and on for any saved or active trail. In the Saved Trails List,
visible trails have a check mark in front of the trail name.
To turn off trail display:
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the de-
sired Trail Name|ENT.
3. Press ↓ → to ACTIVE|↓ to VISIBLE|ENT. To return to the previous page,
press EXIT|EXIT|EXIT|EXIT.
To turn on trail display:
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the de-
sired Trail Name|ENT.
3. Press ↓ → to ACTIVE|↓ to VISIBLE|ENT. To return to the previous page,
press EXIT|EXIT|EXIT|EXIT.
Navigating Trails
There are three methods for following a trail: visual trailing, navigating
a trail (forward) and backtracking a trail (backward). Try each method
to see which you prefer.
Visual trailing is the simplest method. It uses only the Map Page and
requires no menu commands at all. The technique works the same if
you are running a trail forward (from start to end) or backward (from
end to start.) Visual trailing, however, provides no navigation informa-
tion during the trip, such as the time to your destination.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
The other two methods provide a full range of navigation data and work
with both the Map Page and Navigation Page. The only difference be-
tween them is "navigating a trail" follows a trail forward, while "back-
tracking" follows a trail in reverse.
When hiking at walking speed with a hand-held GPS, we often just use
visual back trailing because it is better following each little turn on a
foot path. At faster speeds — like traveling on the highway or on the
water — the Navigate Trail and Backtrack Trail commands are handy.
Visual Trailing
1. On the Map Page, zoom (ZIN or ZOUT) so your trail is visible.
2. Begin moving and watch the Map Page. Simply walk or steer so your
current position arrow moves along the trail you have just made.
Tip:
Generally, when using this method, the smaller the zoom range, the
more accurately you will be able to steer along the trail.
Navigate a Trail (forward)
The following figures illustrate the menu sequence for navigating a
trail.
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the de-
sired Trail Name|ENT.
3. Press → to DELETE TRAIL|↓ to NAVIGATE|ENT.
4. Press ↓ to NAVIGATE|ENT. The unit begins showing navigation infor-
mation along the trail.
NOTE:
If you are already located at or near the beginning of your trail, the
arrival alarm will go off as soon as you hit Enter. Just press EXIT to
clear the alarm.
5. Begin moving and let your GlobalMap guide you.
6. When you reach your destination, be sure to cancel your navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT. The unit asks if you're
sure. Press ←|ENT.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2,
Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with
Navigate command highlighted for Trail 6. A trail is always converted
to a "route" when you navigate the trail.
On the Map Page, the trail you are navigating is represented by a dot-
ted line that alternates with a flashing solid line. The Navigation Page
will also show the navigated trail as a dotted line. The bearing arrow on
the compass rose points to the next waypoint on the trail.
As you travel, the arrival alarm will go off when you near a waypoint.
The bearing arrow on the compass rose will swing around and point to
the next trail waypoint. Press EXIT to clear the alarm.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
North ꢀ
Present
position
arrow
Dotted
trail line
Trail point
Navigate trail, map views: driver is northbound heading straight to-
ward trail point 6 (left). northbound driver has reached point 6 (right)
and has turned west to follow trail.
Track or compass heading indicator
Course
line made
from trail
Cross track
error range
(off course
indicator)
Trail
waypoint
symbol
Arrival
alarm
Navigate trail, navigation page (compass rose) views: driver is north-
bound heading straight toward trail point 6 (left); bearing arrow
shows the trail point is due north (straight ahead.) driver has reached
trail point 6 and must turn west to follow the trail (right). Arrival
alarm goes off and bearing arrow swings around to say turn left (west),
toward the next waypoint, trail point 7. The GlobalMap now shows
navigation information to point 7, which is 1.99 miles away.
Navigate a Back Trail (backtrack, or reverse)
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the de-
sired Trail Name|ENT.
3. Press → to DELETE TRAIL|↓ to NAVIGATE|ENT.
4. Press ↓ to NAVIGATE|→ to REVERSE|ENT|← to NAVIGATE|ENT. The unit
begins showing navigation information along the trail, in reverse.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
If you are already located at or near the end of your trail, the arri-
val alarm will go off as soon as you hit ENT. Just press EXIT to clear
the alarm and proceed.
5. Begin moving and let your GlobalMap guide you.
6. When you reach your destination, be sure to cancel your navigation.
Press MENU|MENU|↓ to CANCEL NAVIGATION|ENT. The unit asks if you're
sure. Press ←|ENT.
Transfer Custom Maps and GPS Data Files
Custom Maps
Custom maps work only from the MMC card or SDC card. When a card
containing a Custom Map File is loaded into the unit, it automatically
loads the map into memory when the unit is turned on.
Instructions for copying Custom Map Files to an MMC are contained in
the instruction manual for your MMC card reader and MapCreate 6
software. For instructions on inserting an MMC into the GlobalMap,
see Sec. 2, Installation/Accessories.
NOTE:
To load a Navionics chart, see Sec. 5 for the entry Navionics Charts.
GPS Data files
GPS Data Files contain waypoints, routes, trails and event marker
icons. Instructions for copying GPS Data Files between your computer
and an MMC are contained in the instruction manual for your MMC
card reader and MapCreate 6 software.
GPS data automatically recorded in the unit's internal memory must be
saved to the MMC (as a GPS Data File) in order to store it on your per-
sonal computer. GPS Data Files stored on an MMC must be copied from
the card to the GlobalMap's internal memory before the unit can read
them. Here's how:
1. Insert the MMC into your unit. Press MENU|MENU|↓ to SYSTEM
SETUP|ENT|↓ to TRANSFER MY DATA|ENT and the screen below appears.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
The Transfer My Data submenu asks if you want to save data to the
MMC or load data from the MMC into the unit's memory.
2. The Transfer My Data menu includes a message that tells you if a
MMC is present or not. If no MMC is present, you must insert a card to
activate the Load or Save commands.
To transfer data from the GlobalMap to the MMC press ENT (for
SAVE.)
To transfer data from the MMC to the GlobalMap press → to
LOAD|ENT.
3. Saving to MMC: To accept the default name "Data" for the GPS
Data File, press ↓ to SAVE DATA|ENT. If you wish to rename the file (as
shown in the following figures), press ENT to activate the file name se-
lection box. Press ↑ or ↓ to change the first character, then press → to
the next character and repeat until the name is correct. Then, press
ENT|↓ to SAVE DATA|ENT.
The unit will display a completion message when the data transfer is
finished. To return to the Page view, repeatedly press EXIT.
These figures (left to right) show the menu sequence for naming and sav-
ing a GPS Data File from the GlobalMap's memory to an MMC.
4. Loading to unit memory: There may be more than one GPS Data
File (*.USR) on the card. To select a file, press ENT to activate the selec-
tion box, use ↓ or ↑ to highlight the file, then press ENT to accept the
56
Download from Www.Somanuals.com. All Manuals Search And Download.
selection. Next, press ↓ to LOAD DATA|ENT. The unit will display a com-
pletion message when the data transfer is finished. To return to the
Page view, press EXIT repeatedly.
Figure 2.
Figure 1.
Figure 3.
Figure 4.
These figures show the menu sequence for loading a GPS Data File
from a MMC into the GlobalMap's memory.
Cancel Navigation
You can turn off any of the navigation commands after you reach your
destination or at any other time by using the Cancel Navigation com-
mand. Press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4:
Advanced GPS Operations
Find Distance to Another Location
1. While on the Map Page press MENU|↓ to FIND DISTANCE|ENT.
2. To check the distance to a location, center the cursor over the desired
position. A rubber band line appears, connecting your current position
to the cursor's location. The distance along that line will appear in a
pop-up box. The box also shows the bearing to the location.
3. Press EXIT to return to regular operation.
The distance from Dallas to Little Rock is 292.2 miles (left). The distance
from the boat's current position to the boat ramp is 0.58 miles (right).
Find Distance From Point to Point
You can also measure distance between two other points on the map.
1. While on the Map Page press MENU|↓ to FIND DISTANCE|ENT.
2. Center your cursor over the first position. (A rubber band line ap-
pears, connecting your current position to the cursor's location.) Press
ENT to set the first point, and the rubber band line disappears.
3. Move the cursor to the second position. The rubber band line reap-
pears, connecting the first point you set to the cursor. The distance
along that line will appear in a pop-up box.
4. Press EXIT to clear the command and return to the page screen.
Icons
Icons are graphic symbols used to mark some location, personal point of
interest or event. They can be placed on the map screen, saved and re-
called later for navigation purposes. These are sometimes referred to as
event marker icons. The unit has 42 different symbols you can pick
from when creating an icon.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Icons are similar to waypoints, but they do not store as much informa-
tion as waypoints do. You can't use a menu to navigate to icons as you
can with waypoints. (But you can use the map cursor and navigate to
any icon on the map.)
You can create an icon at the cursor position on the map, or at your
current position while you are navigating.
Create Icon on Map
1. Use the arrow keys to move the cursor to the location you want to
mark with an icon.
2. Press ENT and the screen shows a Select Icon Symbol menu.
3. Press ← or ↑ or → or ↓ to select your icon symbol, then press ENT.
The icon appears on the map.
Cursor selects icon location (left); Select Icon Symbol menu (center);
Boat Ramp icon on map (right). (Cursor has been moved for clarity.)
Create Icon at Current Position
1. While you are traveling, press ENT and the screen shows a "Select
Icon Symbol" menu.
2. Press ← or ↑ or → or ↓ to select your icon symbol, then press ENT.
The icon appears on the map.
Delete an Icon
You can delete all the icons at one time, you can delete all icons repre-
sented by a particular symbol, or you can use the cursor to delete a se-
lected icon from the map.
1. Press MENU|↓ to DELETE MY ICONS|ENT.
2. Press ↓ to DELETE ALL ICONS, DELETE BY SYMBOL, or DELETE FROM MAP and
press ENT.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
The Delete icons menus
The Delete All Icons command will ask if you are sure. Press ← to
YES|ENT. All icons will be deleted from the map.
The Delete by Symbol command will launch the Select Symbol menu.
Press ← or ↑ or → or ↓ to select the symbol to delete, then press ENT. A
message appears saying all icons with the selected symbol have been
deleted.
The Delete from Map command will prompt you to move the cursor over
an icon to select it. After selecting the icon, press ENT and it disappears
from the map.
Navigate to an Icon
Use the Navigate to Cursor command, and use the cursor to select the
desired icon on the map.
1. Use arrow keys to center cursor cross-hair over the icon.
2. To navigate to the selected icon location press MENU|ENT|EXIT. Fol-
low the course line on the Map Page or the compass bearing arrow on the
Navigation Page.
Routes
A route is a series of waypoints linked together in an ordered sequence
to mark a course of travel. You can visualize a route as a string of
beads. The beads represent waypoints and the string represents the
course of travel connecting waypoint to waypoint.
The course from one waypoint to the next is a leg. Routes are composed
of one or more legs. The legs of all GPS routes are based on straight
lines between waypoints.
A route gives users the capability to navigate through several way-
points without having to reprogram the unit after arriving at each
61
Download from Www.Somanuals.com. All Manuals Search And Download.
waypoint. The GPS unit allows you to navigate forward or backward
through a route. You can even begin navigating in the middle of a
route!
Create and Save a Route
You have the option of creating and editing a route in the unit, or you
can make a route on your computer with our MapCreate 6 software.
PC-created Routes
MapCreate is the easiest method for preparing a route, simply because
your PC's larger screen, keyboard and mouse are easier to manipulate.
To load a MapCreate route into the GlobalMap, follow instructions in
MapCreate's manual for creating a route and saving it as part of a GPS
Data File (file format *.usr). Copy the GPS Data File to an MMC and
insert the MMC in the unit. (See Sec. 2 for instructions on installing
MMCs. To load the GPS Data File into the GlobalMap's memory, see
the entry on Transfer Custom Maps & GPS Data Files in Sec. 3, Basic
GPS Operations.)
Routes Created in the GlobalMap
You can create a route by selecting existing waypoints from the way-
point list or you can set a series of route waypoints on the map with
cursor arrows and the Enter key. In this example, we'll create a route
from the map.
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE,
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
Route Planning command on Main Menu (left),
will open the Route List screen (right).
2. Press ↓ to route name|ENT|↓ to (END OF ROUTE)|ENT|↓ to ADD FROM
MAP|ENT. The Map Page appears with the cursor showing.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit Route menu (left). Edit Route Waypoints menu (right),
with Add From Map command selected.
3. Use the Zoom keys and arrow keys to move the map and cursor until
the cursor is centered on the spot where you want your route to begin.
(If you are starting at your current position or the current cursor posi-
tion, you are already at the starting spot.)
4. Set the first route waypoint and press ENT. In this example, we
started our route at the intersection of 11th Street and 145th E. Ave.
(The route is illustrated in the following figures.)
3.
1.
2.
Route creation sequence (left to right): Fig. 1. Set route waypoint (1) at
11th St. & 145th Ave. Fig. 2. Move cursor north to set point (2) at 145th
& Admiral. Fig. 3. With point (2) set, move cursor east to mark inter-
state on-ramp with waypoint (3). In figures 2 and 3, notice the rubber
band line extending from the previously set waypoint to the cursor.
This line will become the course for the route.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
4.
5.
Route creation sequence, continued: Fig. 4. Point (3) set at on-ramp
turn. Fig. 5. Waypoint (4) set at highway exit to frontage road leading
to river. Waypoint (5) ends the route at a tree stand in the hunting
area. Fig. 6. Press EXIT to save the route and you return to this screen.
5. Move the cursor to the next point in the route, a spot where you need
to turn or change direction, and press ENT to set the next waypoint.
6. Repeat step five until the route reaches your destination.
7. To save your route, press EXIT. The unit reverts to the Edit Route
screen, with the route automatically named "Route 1" and stored in the
GlobalMap's internal memory. (In our example, Route 1 already ex-
isted, so the unit automatically made "Route 2.")
You can edit the route and run other commands, but if you are finished
with the route for now, return to the last page displayed by
pressing EXIT repeatedly.
Delete a Route
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to route name|ENT.
3. Press ↓ to NAVIGATE|ENT|→ to DELETE|ENT|← to YES|ENT.
Tip:
You can also delete all routes at once:
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↑ → to DELETE ALL|ENT|← to YES|ENT.
Edit a Route
You can edit the route name if you wish.
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to route name|ENT|ENT.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press ↑ or ↓ to change the first character, then press → to move the
cursor to the next character and repeat until the name is correct, then
press
ENT.
Return to the previous page by pressing
EXIT|EXIT|EXIT|EXIT.
You can edit the route by adding and removing waypoints.
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to route name|ENT|↓ to WAYPOINTS. Use ↓ and ↑ to select a
waypoint, then press ENT.
Edit Route Waypoints menu.
3. Use ↓ and ↑ to select a command from the Edit Route Waypoints menu
and press ENT. Add From Map lets you insert a waypoint in the route by
selecting a location with the cursor then pressing ENT. Add Waypoint
calls up the Waypoint List so you can insert a waypoint from the list.
Remove Waypoint will delete the waypoint from the route. View Way-
point will show you where the selected waypoint is on the map.
Navigate a Route
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE,
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
Route Planning command on Main Menu (left); Routes menu (center);
Edit Route menu (right) with navigate command is selected.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press ↓ to select route name|ENT|↓ to NAVIGATE|ENT.
3. Upon arrival at your destination, cancel navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
The following figures show what the Navigation Page and Map Page
look like while navigating a route.
Navigate a Route in Reverse
Here's how you run a route backwards, from the end waypoint to the
beginning waypoint.
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE,
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to select route name|ENT|↓ to NAVIGATE|→ to REVERSE|ENT|←
to NAVIGATE|ENT.
3. Upon arrival at your destination, cancel navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
Figure 1.
Figure 2.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4.
Figure 3.
Navigating along a route: Fig. 1 shows the GlobalMap Navigation Page
at the start of a route, heading straight for the first waypoint (Wpt 1). In
Fig. 2, the traveler has arrived at Wpt 1; the arrival alarm has been trig-
gered and the bearing arrow on the compass rose has turned to point
east, toward Wpt 2. In Fig. 3 the traveler has turned east on his new
course and is heading straight for Wpt 2, which is 2.15 miles away. Fig. 4
shows route navigation on the Map Page. In this figure, the traveler has
reached Wpt 2 and is half-way along the leg between Wpts 2 and 3.
Trails
Delete a Trail
This is the command used to erase or delete a trail:
Press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail name|ENT|→ to
DELETE TRAIL|ENT|← to YES|ENT.
Tip:
You can also delete all trails at once:
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press → to DELETE ALL|ENT|← to YES|ENT.
Edit a Trail Name
To edit a trail name: press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail
name|ENT|ENT. Press ↑ or ↓ to change the first character, then press
→ to the next character and repeat until the name is correct. Press ENT
then EXIT|EXIT|EXIT|EXIT to return to the previous page display.
Tip:
You can quickly call up the Edit Trail menu by selecting a trail on
the map with the cursor. Simply move the cursor over a trail and a
pop-up box appears. Press WPT and the Edit Trail menu opens.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Trail selected with map cursor (left). The pop-up box shows distance
and bearing from current position to the selected point on the trail.
The Edit Trail menu (right).
Edit a Trail Color
To edit a trail color: press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail
name|ENT|↓ to COLOR|ENT. Press ↑ or ↓ to select a color style, then
press ENT. Press EXIT|EXIT|EXIT|EXIT to return to the previous page
display.
Edit a Trail Pattern
To edit a trail pattern: press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail
name|ENT|↓ to PATTERN|ENT. Press ↑ or ↓ to change the first character,
then press → to the next character and repeat until the pattern is cor-
rect. Press ENT, then EXIT|EXIT|EXIT|EXIT to return to the previous
page display.
Edit Trail Menu with Pattern option selected (left). Edited trail with
dotted line pattern (right).
Utilities
Utilities are useful tools for traveling or for outdoor activities.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm Clock
To get to the alarm clock menu: press MENU|MENU|↓ to TIMERS|ENT|↓
to ALARM CLOCK|ENT.
Sun/Moon Rise & Set Calculator
To get to the Sun/Moon menu: press MENU|MENU|↓ to SUN/MOON
CALCULATIONS|ENT.
Trip Calculator
To get to the Calculator menu: press MENU|MENU|↓ to TRIP CALCU-
LATOR|ENT.
Trip Down Timer
To get to the Down Timer menu: press MENU|MENU|↓ to TIMERS|ENT|↓
to DOWN TIMER|ENT.
Trip Up Timer
To get to the Up Timer menu: press MENU|MENU|↓ to TIMERS|ENT|ENT.
Waypoints
Delete a Waypoint
To
delete
a
waypoint
from
the
waypoint
list:
press
WPT|ENT|ENT|ENT|↓ to waypoint name|ENT|↓ to DELETE WAY-
POINT|ENT|← to YES|ENT. To return to the previous page, press
EXIT|EXIT.
To delete a waypoint from the map:
1. Use the arrow keys to select the waypoint with the cursor.
2. Press WPT|↓ to DELETE WAYPOINT|ENT|← to YES|ENT. To return to the
previous page and clear the cursor, press EXIT.
To delete all waypoints at one time: press MENU|MENU|↓ to SYSTEM
SETUP|ENT|↓ to DELETE ALL MY WAYPOINTS|ENT|← to YES|ENT. To return
to the previous page, press EXIT|EXIT.
Edit a Waypoint
Waypoint Name
To edit waypoint name: 1. Press WPT|ENT|ENT|ENT|↓ to waypoint
name|ENT|↓ to EDIT WAYPOINT|ENT|ENT.
2. Press ↑ or ↓ to change the first character, then press → to the next
character and repeat until the name is correct. Press ENT then
EXIT|EXIT|EXIT|EXIT to return to the previous page display.
Waypoint Symbol
To edit waypoint symbol: 1. Press WPT|ENT|ENT|ENT|↓ to waypoint
name|ENT|↓ to EDIT WAYPOINT|ENT|↓ to CHOOSE SYMBOL|ENT.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Use arrow keys to select desired symbol and press ENT. To return to
the previous page, press EXIT|EXIT|EXIT|EXIT.
Waypoint Position
To edit waypoint position: 1. Press WPT|ENT|ENT|ENT|↓ to waypoint
name|ENT|↓ to EDIT WAYPOINT|ENT.
2. Latitude: press → to LATITUDE|ENT. Press ↑ or ↓ to change the first
character, then press → to the next character and repeat until the lati-
tude is correct. Press EXIT.
3. Longitude: press ↓ to LONGITUDE|ENT. Press ↑ or ↓ to change the first
character, then press → to the next character and repeat until the lon-
gitude is correct. Press EXIT.
4. When latitude and longitude are correct, return to the previous page:
press EXIT|EXIT|EXIT|EXIT.
Selecting a Waypoint
To select a waypoint on the map (for navigating, editing, etc.,) use the
arrow keys and center the cursor over the waypoint. A highlighted halo
will appear around the waypoint.
Set a Waypoint by Average Position
This feature sets a waypoint at the current position after taking several
position readings and averaging them. This boosts waypoint position
accuracy by helping to eliminate errors caused by atmospheric condi-
tions and other factors.
1. Press WPT|→ to SUBCATEGORY column|↓ to NEW|ENT.
2. Press ↓ or ↑ to AVERAGE POSITION|ENT|press → to CREATE|ENT.
3. Wait while the unit takes points to average for the position. (The greater
the number of points, the greater the accuracy.) When the desired number
of points accumulates, press ENT to create and save the waypoint.
4. The Edit Waypoint menu appears. You can simply save the waypoint
by pressing EXIT|EXIT or you can edit the waypoint.
Set a Waypoint by Projecting a Position
This feature sets a waypoint at a point located a specific distance and
bearing from a reference position. The reference position may be a map
feature or can be selected from your waypoint or Points of Interest lists.
1. Press WPT|→ to SUBCATEGORY column|↓ to NEW|ENT.
2. Press ↓ to PROJECTED POSITION|ENT|→ to CREATE|ENT.
3. Press → to CHOOSE REFERENCE|ENT. Use ↑ and ↓ to select a waypoint,
70
Download from Www.Somanuals.com. All Manuals Search And Download.
map feature or Point of Interest. When the feature has been selected,
press ENT. Now choose the reference point by its name or by simply se-
lect the one nearest your location and press ENT. Choose your reference
point from the list then press ENT|ENT, which will take you back to the
project waypoint screen.
4. Press ↓ to DISTANCE|ENT. Press ↑ or ↓ to change the first character,
then press → to the next character and repeat until the distance is cor-
rect. Press ENT.
5. Press ↓ to BEARING|ENT. Press ↑ or ↓ to change the first character,
then press → to the next character and repeat until the bearing is cor-
rect. Press ENT.
6. Press ↑ to PROJECT|ENT. The Edit Waypoint menu appears. You can
simply save the new projected waypoint by pressing EXIT|EXIT or you
can edit the waypoint. (Press EXIT|ENT if you want to immediately be-
gin navigating to the new waypoint.)
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5:
System & GPS Setup Options
Alarms
This unit has three GPS alarms. The factory default setting has all the
alarms turned on. You can turn the alarms off and on and change their
distance settings.
You can set an arrival alarm to flash a warning message and sound a
tone when you cross a preset distance from a waypoint. For example, if
you have the arrival alarm set to 0.1 mile, then the alarm will flash a
message when you come within 0.1 mile of the recalled waypoint.
The off course alarm warns you when your track drifts too far to the
right or left of the course line to the waypoint. For example, if the
alarm is set to 0.1 mile, then the alarm flashes a message if you drift
0.1 of a mile or more to the right or left of the line to the waypoint.
The anchor alarm is triggered when you drift outside a preset radius.
Again, using the 0.1 mile as an example, if you're anchored and your
boat moves more than 0.1 mile, the alarm will flash a message and
sound a tone.
Alarms command (left); Alarm menu (right).
To change alarm settings:
1. Press MENU|MENU|↓ to ALARMS|ENT.
2. Scroll ↓ or ↑ to select the desired category, then press ENT to check or
clear the Enabled box. This turns the alarm on (checked) or off (un-
checked.)
3. To change distance settings, scroll ↓ or ↑ to select the desired cate-
gory, then press →|ENT to activate the distance dialog box. Press ↑ or ↓
to change the first character, then press → to the next character and
repeat until the name is correct.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
4. When your adjustments are finished, return to the last page dis-
played by repeatedly pressing EXIT.
IMPORTANT ALARM NOTES:
Anchor Alarm — The anchor alarm may be triggered even when
you're sitting still. This typically happens when using small (less
than 0.05 mile) anchor alarm ranges.
Arrival Alarm — If you set the arrival alarm's distance to a small
number and run a route (see the Navigate Routes segment), this
unit may not show navigation data to the next waypoint once you
arrive at the first waypoint. You may not be able to come close
enough to the first waypoint to trip the arrival alarm.
Auto Satellite Search
To lock onto the satellites, the GPS receiver needs to know its current
position, UTC time and date. It needs this data so it can calculate
which satellites should be in view. It then searches for only those satel-
lites. Elevation (altitude) is also used in the equation, but it's rarely
required to determine a position.
When your GPS receiver is turned on for the first time, it doesn't know
your position or elevation (altitude). It does know the current UTC time
and date since these were programmed into it at the factory and an in-
ternal clock keeps the time while the unit is turned off. (If the time
and/or date are incorrect, you can set it using the "Set Local Time" fea-
ture in the System Setup menu.)
The unit begins searching for satellites using the data it acquired the
last time it was turned on, which was probably at the factory. Since it's
almost certain that you're not at our factory, it's likely could be looking
for the wrong satellites.
If it doesn't find the satellites it's looking for after approximately one
minute, it switches to Auto Search. That's when the receiver looks for
any satellite in the sky. Due to advanced technology, the auto search
time has shrunk significantly from the early days of GPS.
Once the unit locks onto the satellites, it should take less than a minute to
find your position the next time it's turned on, provided you haven't moved
more than 100 miles from the last location it was used.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS Auto Search on the GlobalMap Satellite Status Menu.
Here's how to put the unit into auto search mode:
1. Press PAGES until you are on the Satellite Status screen.
2. Press MENU|↓ to GPS AUTO SEARCH|ENT|← to YES|ENT.
Check MMC Files and Storage Space
To check MMC Files:
Press MENU|MENU|↓ to BROWSE MMC FILES|ENT.
Main Menu (left), MMC File Browser (right).
Communications Port Configuration
The unit has two NMEA 0183 version 2.0 compatible communication
ports, or com ports for short. The Com Port Menu, which is accessed
from the System Setup Menu, allows you to configure the communica-
tions ports to send or receive data to another electronic device, such as
an autopilot. Com port 1 and Com port 2 can be used for NMEA.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup Menu with Communications Port highlighted (left) and
Communications Port menu (right).
For assistance in configuring the unit to communicate with another
device, consult the factory. Customer service phone numbers are in the
back of this manual. Also see the entry below for to Configure NMEA.
To set Com Port Configuration:
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT.
2. Press ↓ to COMMUNICATIONS PORT|ENT.
Configure NMEA
You can configure the unit to use specific NMEA sentences.
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT.
2. Press ↓ to COMMUNICATIONS PORT|ENT|↓ to CONFIGURE NMEA|ENT.
3. A menu appears showing the prefixes of the available NMEA sen-
tences. A check mark next to a prefix means the prefix is in use. Use ↑ ↓
→ ← to select a prefix, then press ENT to turn off the prefix.
4. When the desired prefixes are checked or unchecked, press
EXIT|EXIT|EXIT|EXIT to return to the previous page.
Coordinate System Selection
The Coordinate System Menu lets you select the coordinate system to
use when displaying and entering position coordinates.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Menus for changing coordinate system.
To get to Coordinate System Selection:
1. Press MENU|MENU|↓ to GPS SETUP|ENT.
2. Press ↓ to COORDINATE SYSTEM|ENT.
This unit can show a position in degrees (36.14952°); degrees, minutes
and thousandths of a minute (36° 28.700'); or degrees, minutes, seconds
and tenths of a second (36° 28' 40.9"). It can also show position in: UTM
(Universal Transverse Mercator) projection; MGRS (Standard); MGRS
(Standard + 10); Map Fix; Loran TD; British, Irish, Finnish, German,
New Zealand, Swedish, Swiss, Taiwan, Greek and Military grids.
UTM's are marked on USGS topographic charts. This system divides
the Earth into 60 zones, each 6 degrees wide in longitude.
British, Irish, Finnish, German, New Zealand, Swedish, Swiss, Taiwan,
and Greek grid systems are each the national coordinate system used
only in their respective countries. In order to use these grid systems,
you must be in the respective country. This unit will pick the matching
datum for you when you select the grid. See the entry on Map Datum
Selection for more information.
The military grid reference system (MGRS) uses two grid lettering
schemes, which are referred to as standard and standard + 10 MGRS
on this unit. Your position and datum in use determines which one to
use. If you use standard, and your position is off significantly, then try
the alternate.
NOTE: When the position format is changed, it affects the way all posi-
tions are shown on all screens. This includes waypoints.
To change the coordinate system, press ENT while COORDINATE SYSTEM is
highlighted. Press ↑ or ↓ arrow keys to highlight the desired format.
Press ENT to select it. Press EXIT to clear the menus.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
To setup Loran TD:
NOTE:
If the Loran TD conversion is chosen, you must enter the local Lo-
ran chain identification for the master and slaves. Do this by se-
lecting "Setup Loran TD" at the bottom of the "Coordinate System"
menu and select the ID. Press EXIT to clear this menu.
Configure Loran TD menu.
Map Fix
Map Fix is used with charts or maps. This system asks for a reference
position in latitude/longitude, which you take from a marked location
on the map. It then shows the present position as distance on the map
from that reference point.
For example, if it shows a distance of UP 4.00" and LEFT 0.50", you
then measure up four inches and to the left a half-inch from the refer-
ence point to find your location on the map.
Configure a map fix:
First, take your map of the area and determine a reference lati-
tude/longitude. (Please note that in order for this system to work, the
latitude/longitude lines must be parallel with the edge of the map.
USGS maps are parallel, others may not be. Also, this works better
with smaller scale maps.) The reference position can be anywhere on
the map, but the closer it is to your location, the smaller the numbers
will be that you'll have to deal with.
Once you've decided on a reference position, you can save it as a way-
point. See the waypoint section for information on saving a waypoint.
Save the reference position as a waypoint. Exit from the waypoint
screens.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Press MENU|MENU|↓ to GPS SETUP|ENT.
2. Press ↓ to COORDINATE SYSTEM|ENT.
3. Press ↓ to SETUP MAP FIX|ENT.
The following screen appears, and MAP SCALE is highlighted. Press ENT
and enter the map's scale. This is generally at the bottom of the paper
map. It's shown as a ratio, for example 1:24000. Press EXIT and the unit
returns to the Configure Map Fix screen.
Configure a map fix so the GlobalMap can find your position on a
printed chart or topographical map.
Press ↓ to SELECT ORIGIN WAYPOINT|ENT|ENT|ENT to bring up the way-
point list. Select the waypoint that you saved the reference point under
and press ENT. The unit displays a waypoint information screen with
the command SET AS ORIGIN selected. Press ENT and the unit returns to
the Configure Map Fix menu. Finally, press EXIT to clear this menu.
Now press ↑ to COORD SYSTEM|ENT, select MAP FIX from the list and press
ENT|EXIT|EXIT|EXIT. All position information now shows as a distance
from the reference point you chose.
Customize Page Displays
Every Page display option except Full Map (on the Map Page) has cus-
tomizable data boxes to provide constant on-screen information.
The various data available from your unit are divided into categories in
the Data Viewer menu. These categories include GPS Data, Navigation,
Trip Calculator, Time, and Miscellaneous Data. You can select items
from any of these categories for display in any data box — the category
divisions are only there to help you sort through the information.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the information displayed in a data box:
On the Page display you wish to change, press MENU|↓ to CUSTOM-
IZE|ENT. A data box name flashes, indicating it is selected. Press ENT to
change the box or hit ↑, ↓, → or ← to select another box, then press ENT.
You'll see a list of categories with "+" or "–" symbols next to each cate-
gory. A category with a "+" is expandable, meaning its contents are hid-
den.
Customize Menu, with the GPS Data category expanded.
Selecting the category name and pressing ENT will show the category's
contents, so you can choose items within it. An expanded category (one
with a "–" next to its name) can be collapsed to hide its contents. Just
select the category name and press ENT.
Expand any categories that might contain data you want to display.
Then press ↓ or ↑ to select a different data option. With the new option
highlighted, press ENT to switch the contents of the box to the new data
type, then press EXIT. You can now select another box to change. When
you are finished with the settings, press EXIT again to end the Custom-
ize command, and the box name stops flashing.
A Page display can show a limited number of data boxes. You can not
turn them off or add more data boxes.
GPS Simulator
The GPS simulator lets you use the unit as if you were outdoors navi-
gating somewhere. It's a great way to become familiar with all the unit's
features. You can set the starting location by entering latitude/longitude
(Starting Position) or from a stored waypoint, map place or POI location
(CHOOSE START command). You can steer your position and change speed
on the map by using the arrow keys (STEER WITH ARROWS command) or by
setting the track and speed in the dialog boxes provided on the simulator
menu screen.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
To get to the GPS Simulator:
1. Press MENU|MENU|↓ to GPS SETUP|ENT.
2. Press ↓ to GPS SIMULATOR|ENT. The GPS Simulator Menu appears.
GPS Setup Menu (left); GPS Simulator menu (right).
Make the desired settings, then turn the simulator on by highlighting
the GPS SIMULATOR ON box and pressing ENT key. Press EXIT|EXIT|EXIT
to clear this menu. A message and tone appear periodically, warning
you that the simulator is on. To turn the simulator off, repeat the above
steps or turn off the unit.
While in simulator mode, you can press EXIT to clear the steering and
speed boxes from the screen while continuing the simulation. This will
allow you to use the map cursor during a simulation. To turn steering
and speed boxes back on again, return to the GPS Simulator menu, se-
lect the STEER WITH ARROWS command, press ENT, then press
EXIT|EXIT|EXIT to return to the previous page.
Simulating Trail or Route Navigation
In Simulator mode, your unit can automatically follow a trail or route
without manual steering if you use these steps:
1. From the Map Page, go to the simulator menu. Pick a STARTING PO-
SITION at or near the beginning of your trail/route. Enter an approximate
TRACK (shown in compass degrees) that will point you toward the start
of the trail/route.
2. Set SPEED to zero. Select STEER WITH ARROWS command and press ENT,
which turns on the simulator and returns you to the Map Page.
3. Begin navigating along the trail/route. (If you are close enough to the
first waypoint, the arrival alarm will usually go off as soon as naviga-
tion begins. Press EXIT to clear the alarm.) When navigation starts,
press ↑ to increase speed to the desired setting.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press EXIT to turn off the steering and speed boxes. The unit will now
automatically "steer" along the trail or route. When you arrive at your
"destination," cancel navigation as you normally do.
Tip:
You can pick any spot on the map to begin your simulation session
by using the Initialize GPS command. This makes your unit think
it's located at the position you select. See the following entry.
Initialize GPS
This command is handy when you are practicing in simulator mode.
(See the entry in this section for GPS Simulator.) In simulator mode,
this command makes the unit operate as if it is sitting someplace other
than its actual location. So, you and your unit could be located in Kan-
sas City, but practice navigating in the ocean off Islamorada, Florida.
1. Press MENU|MENU|↓ to GPS SETUP|ENT|ENT.
2. A message appears, telling you to move the cursor near the desired
location and press ENT. When the message automatically clears, follow
the message instructions.
3. In a moment, your present position marker arrow appears on the
map in the location you selected with the cursor. The unit will consider
that spot as it's last known position until changed by either a live sat-
ellite lock-on or a new simulator location.
Map Auto Zoom
This receiver has an auto zoom feature that eliminates much of the but-
ton pushing that other brands of GPS receivers force you to make. It
works in conjunction with the navigation features.
First, start navigation to a waypoint. (See the waypoint section for
more information on navigating to a waypoint.) Then, with the auto
zoom mode on, the unit zooms out until the entire course shows, from
the present position to the destination waypoint. As you travel toward
the destination, the unit automatically begins zooming in — one zoom
range at a time — always keeping the destination on the screen.
To turn this feature on, from the MAP PAGE, press MENU|↓ to AUTO
ZOOM|ENT|EXIT. Repeat these steps to turn it off.
Map Data
This menu lets you turn the map off, if desired (which turns the map
screen into a GPS plotter); turn off or on the pop-up map info boxes;
draw the map boundaries or boxes around the areas of high detail; or
fill land areas with gray. You can also turn on or off Map Overlays,
82
Download from Www.Somanuals.com. All Manuals Search And Download.
which display latitude and longitude grid lines or range rings on the
map. This menu lets you select Navionics Maps. For instructions, see
the Navionics Charts entry in this section.
To get to Map Data:
From the Map Page, press MENU|↓ to MAP DATA|ENT.
Map Menu (left) and Map Data Menu (right).
Earth Map Detail
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ENT to
check to select the level of map detail you prefer. Use ↑ ↓ to choose off,
low, medium or high, then press EXIT to the page display.
Pop-up Map Info
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ to POPUP
MAP INFO. With the option highlighted, press ENT to check it (turn on)
and uncheck it (turn off.) After the option is set, press EXIT|EXIT to re-
turn to the page display.
Draw Map Boundaries
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ to DRAW
MAP BOUNDARIES. With the option highlighted, press ENT to check it (turn
on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to
return to the page display.
Fill Water with White
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ to FILL
WATER WITH WHITE. With the option highlighted, press ENT to check it
(turn on) and uncheck it (turn off.) After the option is set, press
EXIT|EXIT to return to the page display.
Trackline Extension
Trackline Extension is a new tracking option that provides a visual in-
terpretation of your velocity. It charts how long it will take to travel a
predetermined distance based on your current navigational informa-
tion. Distance is shown on one side of the track with estimated time of
83
Download from Www.Somanuals.com. All Manuals Search And Download.
arrival on the other. Below the Trackline Extension window are two
check boxes — Show Time and Show Distance — which allow you to
turn on or off the time and/or distance settings.
To set trackline extension: From the Map Page, press MENU|↓ to
MAP DATA|ENT. Press ↓ to TRACKLINE EXTENSION|ENT. Use ↑ ↓ to select the
desired distance setting and press ENT.
Presentation Mode
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ and → to
PRESENTATION MODE|ENT. Use ↑ ↓ to choose the desired depth and press
ENT. Presentation Mode gives you some control over the map layout by
allowing you to choose between US and International Modes.
Safety Contour
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ and → to
SAFETY CONTOUR|ENT. Use ↑ ↓ to choose the desired depth and press ENT.
The SAFETY CONTOUR command allows you to modify depth contours on a
navionics map for water less than 10 meters deep. Based on your pref-
erences, the depth contours will be colored or shaded to make it easier
to identify shallow areas. Keep in mind the size of your ship's keel
when determining which option is right for your vessel.
Map Overlays (Range Rings; Lat/Long Grid)
The map screen can be customized with four range rings and/or grids
that divide the plotter into equal segments of latitude and longitude.
Range rings are handy for visually estimating distances on the map.
The ring diameters are based on the current zoom range. For example:
at the 100-mile zoom, the screen will show two rings with your current
position in the center. The large ring touching the left and right sides of
the screen is 100 miles in diameter (same as the zoom range). The sec-
ond smaller ring is 50 miles in diameter (always 1/2 the zoom range).
The distance from your current position to the smaller ring (the ring's
radius) is 25 miles (always 1/4 the zoom range). With the arrow keys
and map cursor, you can scroll the map to see the third and fourth
rings. In this example, the distance to the third ring is 75 miles and
distance to the fourth ring is 100 miles from your current position.
To set range rings: From the Map Page, press MENU|↓ to MAP
DATA|ENT. Press ↓ and → to RANGE RINGS. With the option highlighted,
press ENT to check it (turn on) and uncheck it (turn off.) After the op-
tion is set, press EXIT|EXIT to return to the page display.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
To set Lat/Long Grid: From the Map Page, press MENU|↓ to MAP
DATA|ENT. Press ↓ and → to LAT/LON GRID LINES. With the option high-
lighted, press ENT to check it (turn on) and uncheck it (turn off.) After
the option is set, press EXIT|EXIT to return to the page display.
Map Datum Selection
Maps and charts are based on a survey of the area that's covered by the
map or chart. These surveys are called "Datums." Maps that are cre-
ated using different datums will show the same latitude/longitude in
slightly different locations.
All datums are named. The GPS system is based on the WGS-84 da-
tum, which covers the entire world. Other datums may also cover the
entire world, or just a small portion of it. By default, your position
shows using the WGS-84 datum. It, however, can show your position
using one of 191 different datums. To change the datum:
1. Press MENU|MENU|↓ to GPS SETUP|ENT|↓ to DATUM SELECTION|ENT.
2. Scroll ↓ or ↑ to select the desired datum, then press ENT.
3. To return to the last page displayed, press EXIT|EXIT.
A list of the datums used by this unit is in the back of this manual.
GPS Setup Menu (left) and Map Datum menu (right).
Map Detail Category Selection
This menu determines which of the mapping features are shown on the
screen. This includes waypoints, trails, icons, cities, highways, etc. You
can selectively turn on or off any of these items, customizing the map to
your needs.
To get to Map Categories:
1. From the Map Page, press MENU|↓ to MAP CATEGORIES DRAWN|ENT.
2. Press ↑ or ↓ to select a category or press → then press ↑ or ↓ to select
a subcategory. Press ENT to turn it off (no check) or on (checked.)
85
Download from Www.Somanuals.com. All Manuals Search And Download.
3. To return to the last page displayed, press EXIT|EXIT.
Map menu (left) and Map Categories Drawn menu (right).
Map Orientation
By default, this receiver shows the map with north always at the top of
the screen. This is the way most maps and charts are printed on paper.
In Track Up mode, map shows "N" and arrow to indicate north.
Map orientation shown in north up (left) and track up (right).
This is fine if you're always traveling due north. What you see to your
left corresponds to the left side of the map, to your right is shown on
the right side of the map, and so on. If, however, you travel any other
direction, the map doesn't line up with your view of the world.
To correct this problem, a track-up mode rotates the map as you turn.
Thus, what you see on the left side of the screen should always be to
your left, and so on.
Another option is course-up mode, which keeps the map at the same
orientation as the initial bearing to the waypoint. When either the
track-up or course-up mode is on, a "N" is displayed on the map screen
to show you which direction is north.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
To change map orientation: from the Map Page, press MENU|↓ to MAP
ORIENTATION|ENT. Use ↑ or ↓ to select the desired mode, then press ENT.
Press EXIT|EXIT to return to the page display.
Map Menu (left) and Map Orientation menu with
the North Up map orientation option selected (right).
Navionics Charts
Your unit can display Navionics electronic charts on MMCs. They
work just like a MapCreate custom map on a MMC.
Entrance to Chesapeake Bay in a MapCreate 6 custom map with a 10-
mile zoom (left). The same position on Navionics chart at
6-mile zoom (center) and with a 5-mile zoom (right).
To display a Navionics chart:
1. Install the Navionics MMC in the memory card compartment and
turn on the unit. (For full card install instructions, see Sec. 2.)
WARNING:
You should never format the MMC containing your
Navionics chart. Formatting the MMC will permanently
erase the chart from the card.
2. From the Map Page, press MENU|↓ to MAP DATA|ENT|→ to MAP DATASET
CHOICE|ENT. Use ↓ key to select the NAVIONICS, then press ENT.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
These figures show menu sequence (from left to right) for selecting a
Navionics chart for the South Chesapeake Bay area.
3. Use ↓ key to select NAVIONICS MAP CHOICE and press ENT. Use ↑ ↓ keys
to select a map and press ENT|EXIT|EXIT.
4. To turn off a Navionics chart, from the Map Page, press MENU|↓ to
MAP DATA|ENT|→ to MAP DATASET CHOICE|ENT. Use ↑ or ↓ to select one of
the three other options — Standard, Nautic Path or HotSpots Elite — then
press ENT|EXIT|EXIT.
Port Information
Navionics charts contain Port Services information, represented by anchor
icons on the map display. An example is displayed in the following figure.
To view Port Services information:
1. Use the arrow keys to move the cursor over a Port Services icon.
When selected, a pop-up name box appears.
2. Press WPT to display the Port Services Information screen.
The Port Services information screen has two windows. The top window
lists the various service categories. The lower window lists the detailed
services available in each basic category.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Port Services
icons
Pop-up
name box
Cursor lines
Navionics chart showing Port Services icon selected by cursor.
3. To scroll through the Service Categories window: press ENT then use
↑ or ↓ to see the types of services available. As you highlight a different
category, the list in the lower window changes. To return to the Map
Page, press EXIT|EXIT.
4. The General Services category includes a long list of items in the De-
tailed Services window. To scroll through the Detailed Services window
from SERVICE CATEGORIES, press ↓ to DETAILED SERVICES|ENT, then use ↑ or
↓ to read the list of available services. To return to the Map Page, press
EXIT|EXIT. To return to the top service category window, press ENT|↑.
Port Services information screens.
Tidal Current Information
Navionics charts contain Tidal Current information,
represented at large zoom ranges by a box icon with
the letter "C." The icon stands for a Tidal Current
Station location.
When you zoom in to a sufficiently small zoom range, the icon itself be-
comes an animated arrow showing tidal current velocity and direction
for the selected tidal station. At larger zoom ranges, you can select the
boxed "C" icon and it becomes an animated arrow with a pop-up name
box. An example is displayed in the following figure.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
To view Tidal Current information:
1. Use the arrow keys to move the cursor over a Tidal Current Station
icon. When selected, a pop-up name box appears.
2. Press WPT to display the Tidal Current Information screen.
Tidal Cur-
rent
Station icon
in animated
mode
Pop-up
name box
Cursor lines
Navionics chart showing Tidal Current Station icon selected by cur-
sor. In this example, the tidal current is in flood but it's about to enter
the slack water stage. The current is flowing to the west at 0.1 mph.
Current Information screen.
The Tidal Current Information screen displays daily tidal current data
for the station at the present time. The graph at the top of the example
above is an approximate view of the flood and ebb pattern from mid-
night (MN), to noon (NN) to midnight (MN). The velocity scale at the
top left side of the graph changes dynamically based upon the maxi-
mum velocity of the current for that day.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Slack water, the period of little or no current, is represented by the
Slack Water Line (SWL). The flood appears above the SWL and the ebb
appears below the SWL.
You can look up tidal current data for other dates by changing the
month, day and year selection boxes. To select another date:
1. Use → and ← to highlight month, day or year, then press ENT.
2. Use ↑ and ↓ to select the desired month, day or year, then press ENT.
To clear the information screen, press EXIT.
Tide Information
Navionics
charts
contain
Tidal
Information,
represented at large zoom ranges by a box icon with
the letter "T." The icon stands for a Tidal Station
location. An example is displayed in the figure on the
right.
When you zoom in to a sufficiently small zoom range, the icon itself be-
comes an animated gauge showing a rising or falling tidal height for the
selected station. At larger zoom ranges, you can select the boxed "T" icon
and it becomes an animated gauge with a pop-up name box. An exam-
ple is displayed in the following figure.
To view tide information:
1. Select a Tide Station icon: use the arrow keys to move the cursor over
an icon. When it is selected, a pop-up name box appears.
2. After selecting the Tide Station icon, press WPT to display the Tide
Information screen.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Cursor line
Pop-up
name box
Tide Station
icon
Navionics chart showing Tide Station icon selected by cursor.
In the example above, the tide is at 2.8 feet and falling,
as shown by the down arrow at the top of the icon.
Tide Information screen.
The Tide Information screen displays daily tidal data for the station at
the present time. The graph at the top of the screen is an approximate
view of the tidal range pattern for the day, from midnight (MN), to
noon (NN) to midnight (MN). The dotted line across the graph is the
Mean Lower Low Water line (MLLW).
The height scale on the top right side of the graph changes, based upon
the maximum range of the tide for that day. The MLLW line also ad-
justs its position as the height scale changes.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
You can look up tidal data for other dates by changing the month, day
and year selection boxes. To select another date:
1. Use → and ← to highlight month, day or year, then press ENT.
2. Use ↑ and ↓ to select the desired month, day or year, then press ENT.
To clear the information screen, press EXIT.
Overlay Data
On any Page display except Satellite Status, you can "float" or overlay
additional GPS or navigation data on the screen with the Overlay Data
command. For example, if you left your watch at home, you could dis-
play the local time on top of the map. Or, if you wanted to see details
about your route and trip, you could show your bearing, course, average
speed and trip distance.
The various data available from your unit are divided into categories in
the Overlay Data menu. These categories include GPS Data, Naviga-
tion, Trip Calculator and Time.
You can select items from any of these categories for display, in any
combination — the category divisions are there only to help you sort
through the information.
NOTE
The Customize command and the Overlay Data command both use the
same information categories. The difference between the two com-
mands is that Customize changes only the digital data boxes on a
screen, and Overlay Data changes only the information floating on the
screen without a box. See Customize Page Displays, on page 79 for in-
formation on customizing data boxes.
Overlay Data highlighted on GPS menu (left). The Data Viewer menu with
the Navigation category expanded.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
To overlay information on your screen:
1. While on the Navigation Page or a Map Page, press MENU|↓ to
OVERLAY DATA|ENT.
2. You'll see a list of the overlay data currently shown on the screen, if
any overlay data has been chosen for display. Select (ENTER TO ADD) and
press ENT. The data viewer shows information categories with "+" or "–"
symbols next to each category name. A category with a "+" next to it is
expandable, meaning its contents are hidden.
Selecting the category name and pressing ENT will show the category's
contents, so you can choose items within it. An expanded category (one
with a "–" next to its name) can be collapsed to hide its contents. Just
select the category name and press ENT.
3. Expand any categories that might contain data you want to display.
Then press ↓ or ↑ to select a data option.
4. With the data option highlighted, press ENT to check it (turn on) and
uncheck it (turn off). As you turn it on, the data will appear on top of
the screen. Every Page display has a maximum number of items you
can show using the Overlay Data command.
5. After the desired changes are made, press EXIT|EXIT to return to the
page display.
From Overlay Data Shown menu (left) press ENT to see Data Viewer
(center). Select a category and press ENT. Bearing, Closing Speed and
Off Course have been selected from the Navigation category.
To remove overlaid data:
1. While on the Page that shows the item or items you want to remove,
press MENU|↓ to OVERLAY DATA|ENT.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
2. You'll see a list of the overlay data currently displayed. Select the
item you want to remove from your display and press ENT|ENT to re-
move the data. To remove another item, select the item and press
ENT|ENT.
3. When you have finished removing all the items you want from the
screen, press EXIT to return to the page display.
Overlay Data Shown menu with Off Course option selected (left). Press
ENT to access Remove option (right). Press ENT again to remove item.
To move overlaid data:
You may find it useful to rearrange data that is floating in your display
window.
1. From one of the Map Pages, press MENU|↓ to OVERLAY DATA|ENT.
2. You'll see a list of the overlay data currently displayed. Select the
item you want to move and press ENT|→ to MOVE|ENT.
3. The data begins to flash on your screen. Use any combination of →,
←, ↑ and ↓ to move the data to a new location on the screen.
4. When satisfied, press EXIT|EXIT.
To resize overlaid data: press MENU|↓ to OVERLAY DATA|ENT. This will
bring up the Overlay Data Shown menu with a list of the current over-
lay data. Use → ← to toggle the size of the data between small, me-
dium, large and enormous. When you are satisfied with the data size,
press EXIT. You can also change the data size by highlighting the data
you want to change on the Overlay Data Shown menu and pressing
ENT. This will bring up the data information menu. Use ↓ to select
overlay size, then press ENT. Select the desired data size, then press
EXIT|EXIT|EXIT to return to the main screen.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Overylay Data Style
Do you like a digital readout or do you prefer an analog gauge look?
With the Overlay Style feature you can mix and match your data to suit
your viewing preferences.
To access overlaid data style menu: press MENU|↓ to OVERLAY
DATA|ENT. This will bring up the Overlay Data Shown menu with a list
of current overlay data. Highlight the data you want to change on the
Overlay Data Shown menu and press ENT, which will launch the data
information menu. Use ↓ to select overlay style, choose analog, and
press ENT. Next, press → to enter Analog Setup, which will place a
gauge on the display instead of digital numbers.
The GlobalMap Data Information menu (left) with the Overlay style
window activated. After choosing analog, the Analog Setup button ap-
pears (right).
Gauge Setup Menu.
There are four primary setup options in the analog menu: Themes, Tick
Marks, Thresholds and Text. When working in the gauge setup menu,
use ↓ ↑ and → ← to highlight the desired option, then press ENT.
Pressing EXIT will take you back to the previous screen.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
You can make gauges transparent from all the setup menus except
Text Setup.
Themes setup allows you to change gauge style, color scheme, and
needle style.
Gauge Style
There are five gauge settings:
Single analog: supports one analog gauge.
Split analog: features two gauge elements and two gauge needles in
one analog gauge. Each element uses one-half of the gauge.
Analog/Digital: a regular analog gauge with digital data in the center.
Dual Analog: a pair of analog gauges.
Analog + Digital: features a large analog gauge coupled with a small
digital gauge.
Gauge Select
There are two choices under gauge select: Primary and Secondary. The
secondary button is not an active button unless you have more than one
gauge set for display, which applies to all gauge styles except Single
Analog.
With a single gauge displayed (left), the Sec. Data button is not active.
After choosing a dual-gauge setting, the Sec. Data button is active.
Choosing the Sec. Data button will take you to the same Data Viewer
screen (right) as Customize Page and Overlay Data commands.
The Secondary Data or Sec. Data button is only active when you have a
dual-gauge setting selected for display. It allows you to choose what
information you want displayed in secondary gauge. The secondary
data button takes you to the same Data Viewer screen as the Custom-
ize Page and Overlay Data commands.
Color Scheme
GlobalMap color models have three color options, white, blue and black.
GlobalMap monochrome models have two options, white and black.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Needle Style
The GlobalMap has four needle styles, Triangular, Beveled, Big Needle
and Compass.
Tick Marks setup menu (left) with Thresholds Setup menu (right).
Gauge Setup
Tick Marks setup gives you the option of modifying the gauges mini-
mum and maximum angles, values and ticks.
Minimum and Maximum Angles gives you control over the numerical
layout of the gauge. You can spread the numbers out around the gauge
or bunch them together in a smaller area.
Minimum and Maximum Values allows you to decide where the gauge's
numbers will begin and where they will top out. For example: you may
decide to start the gauge at 0, 5 or 10 and top it out at 85, 90 or 100.
Minimum or Maximum Tick controls how many tick marks will be dis-
played on the gauge. If you set the minimum tick to 1 and the max tick
to 10, there will be 10 tick marks between 0 and 10, 10 and 20 and so
on. In the case of a speedometer, that's one tick for one mile per hour. If
you change the minimum tick to 2 and leave the maximum tick at 10,
you'll have one tick for every two miles per hour. That's five ticks be-
tween 0 and 10, 10 and 20 and so on.
Thresholds setup can be used as a visual aid to mark portions of the
gauge. It is divided into Upper and Lower Thresholds, each containing
major (warning) and minor (caution) threshold settings. Two sets of
numbers must be entered for each threshold. Minor thresholds ranges
are colored yellow. Major threshold ranges are red.
GlobalMap monochrome models use different shades of gray to separate
thresholds from the rest of the gauge.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
GlobalMap Text Setup menu( left) with transparent gauge labeled as
"track"; Text Setup menu with destination house number entered in
units text position (right).
Text setup allows you to individually label gauges. There are two win-
dows in Text Setup: Gauge Text and Units Text. Units Text is posi-
tioned at the bottom of the gauge. Gauge Text is located above the
Units Text.
Default
The Default command restores the factory default settings. If you run
into trouble modifying any of the gauge settings, Default is there to bail
you out. The button is labeled RESTORE DEFAULTS in some models.
NOTE:
The Analog setup menus allow you to make gauges transparent. De-
spite their transparency, the gauges take up much of the display
screen.
A display with a transparent track gauge (left). The screen on the right
is displaying Track and speed gauges.
Pop-up Help
Help is available for virtually all of the menus on this unit. By high-
lighting a menu item and leaving it highlighted for a few seconds, a
99
Download from Www.Somanuals.com. All Manuals Search And Download.
"pop-up" message appears that describes the function of the menu item.
This feature is on by default.
To set up Popup Help: Press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓
to POPUP HELP. With the option highlighted, press ENT to check it (turn
on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to
return to the page display.
System Setup menu (left) with Pop-up Help command highlighted. The
Pop-up Help message for the Screen command (right).
Reset Options
To reset all features to their factory defaults:
Press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓ to RESET OPTIONS|ENT|← to
YES|ENT.
NOTE:
Reset Options does not erase waypoints, routes, icons or plot trails.
Reset Options command (left) and the Reset Options menu (right).
Screen Contrast and Brightness
To access the Screen menu, press MENU|MENU|ENT.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Once in the Screen menu:
To adjust the display's contrast:
The CONTRAST slider bar is already selected. Press → or ← to move the
bar. The left end of the scale is minimum contrast. The right end is
maximum contrast.
Screen Command (left); Screen Menu with Contrast bar selected (right).
To adjust the display's brightness:
Press ↓ to BRIGHTNESS. Press → or ← to move the bar. The left end of the
scale is minimum contrast. The right end is maximum contrast.
To adjust the screen's display mode:
Press ↓ to DISPLAY MODE|ENT|press ↑ or ↓ to select mode|EXIT.
Display Mode menu.
Set Language
This unit's menus are available in 10 languages: English, French, Ger-
man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish.
To select a different language:
101
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT.
2. Press ↓ to SET LANGUAGE|ENT.
3. Use ↓ or ↑ to select a different language and press ENT. All menus
now appear in the language you selected.
Set Local Time
Using the correct local time setting is handy when estimating local ar-
rival time while navigating. Also, the time and date are saved when a
waypoint is created.
To access the Set Local Time menu, you must first acquire your posi-
tion. Once that is done press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓ to
SET LOCAL TIME|ENT.
Once in the Time Settings menu:
To set Local Time: Press ENT. Press ↑ or ↓ to change the first character,
then press → to move the cursor to the next character. Repeat until the
time is correct, then press ENT.
To set the Month: Press ↓ to MONTH|ENT. Press ↑ or ↓ to select the month,
then press ENT.
To set the Day: Press → to DAY|ENT. Press ↑ or ↓ to select the day, then
press ENT.
To set the Year: Press → to YEAR|ENT. Press ↑ or ↓ to select the year,
then press ENT.
Time Settings Menu.
To Set Time Format: Press ↓ to the Time Format window. Just highlight
the option you prefer — 12 or 24 hour — and press ENT.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
To Set Date Format: Press ↓ and → to modify the Date Format. There are
three options: Month/Day/Year, Day/Month/Year and Year/Month/Day.
Use ↑ or ↓ to select the format you prefer, then press ENT.
The last field we have to discuss is CONFIG DST. This feature allows your
unit to automatically adjust Daylight Saving Time (you should only have
to set it once). You may select which set of rules matches DST in your
region, or simply accept the default. Use the ↓ key to configure DST.
Once you have each field set the way you want, press EXIT repeatedly
until you return to the previous page.
Show WAAS Alarm
When the signal is available, your unit will automatically use WAAS to
boost the accuracy of the position fix. When the WAAS signal is lost or
acquired, an alarm message appears. Since the U.S. government is still
developing the WAAS system, it's not unusual for a GPS/WAAS re-
ceiver to frequently lose and reacquire its lock on a WAAS satellite.
That can result in the alarm repeatedly going on and off. If you want,
you have the option of turning off the WAAS Acquired/Lost alarm with-
out affecting how the unit uses WAAS. Here's how:
1. Press MENU|MENU|↓ to GPS SETUP|ENT|↓ to SHOW WAAS ALARM.
2. With the option highlighted, press ENT to uncheck it (turn off) and
check it (turn on). After the option is set, press EXIT|EXIT to return to
the page display.
3. You can return to this command and press ENT again to turn on the
feature.
Software Version Information
From time to time, Lowrance updates the operating system software in
some of its products. These software upgrades are usually offered to
customers as free downloads from our web site, www.lowrance.com.
These upgrades make the unit perform better or introduce a new fea-
ture or function. You can find out what software version is running in
your GlobalMap by using the Software Information command.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Software Information command on the System Setup menu.
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓ to SOFTWARE INFO|ENT.
2. Read the information displayed on the screen.
3. To return to the last page displayed, press EXIT|EXIT|EXIT.
Sounds and Alarm Sound Styles
Sounds triggered by key strokes and alarms can be adjusted:
Press MENU|MENU|↓ to SOUNDS|ENT.
Sounds command (left); The Sounds menu (right).
Once in the Sounds menu:
To set Key Press Sounds: With the option highlighted, press ENT to
check it (turn on) and uncheck it (turn off). After the option is set, press
EXIT|EXIT to return to the page display.
To set Alarm Sounds: Press ↓ to ALARM SOUNDS. With the option high-
lighted, press ENT to check it (turn on) and uncheck it (turn off). After
the option is set, press EXIT|EXIT to return to the page display.
To set External Audio (unavailable in some models): Use → to highlight the
option. Press ENT to check it (turn on) and uncheck it (turn off). After
the option is set, press EXIT|EXIT to return to the page display.
To set Alarm Volume: Press ↓ to VOLUME. Press → or ← to move the bar.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
The left end of the scale is low volume; the right end is high volume. Af-
ter the option is set, press EXIT|EXIT to return to the page display.
To set Alarm Style: Press ↓ to ALARM STYLE|ENT. Press ↑ or ↓ to change
the style, then press ENT. After the option is set, press EXIT|EXIT to re-
turn to the page display.
Track Smoothing
This is a factory setting on the GPS Setup menu that should always be
left on. When stopped or traveling at slow speeds (such as walking or
trolling), Track Smoothing prevents wandering of trails.
Track Smoothing option turned on.
Trail Options
There are several options you can use with trails. Some affect all trails,
other options can be applied to a particular trail. You can change the
way trails are updated, you can display or hide trails, make them flash,
create a new trail, delete a trail, etc.
General Trail Options
To access the Trails Menu:
Press MENU|MENU|↓ to MY TRAILS|ENT.
Main Menu (left), Trails Menu (center) and Trail Options menu (right).
Delete All Trails
To remove all of the trails from memory: from the Trails Menu, press →
to DELETE ALL|ENT|← to YES|ENT.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Update Trail Option
This menu lets you change the way trail updates occur.
WARNING:
If you uncheck the Update Trail option, automatic trail
creation and recording will be turned off. You must turn
it back on to record trails. The default setting is on.
From the Trails Menu, press → to OPTIONS|ENT. With UPDATE ACTIVE TRAIL
highlighted, press ENT to check it (turn on) and uncheck it (turn off).
Update Trail Criteria (Auto, Time, Distance)
The options are automatic, time, or distance. When it's in the default
automatic mode, the unit doesn't update the plot trail while you're
traveling in a straight line. Once you deviate from a straight line, the
unit "drops" a plot point (trail waypoint) onto the trail. This conserves
trail points. If a plot trail uses all of the available points allotted to it,
the points at the start of the trail are removed and replaced by points at
the end of the trail.
From the Trails Menu, press → to OPTIONS|ENT|↓ to UPDATE CRITERIA.
Press ↑ or ↓ to select criteria type|ENT.
Trail Update Rate (Time, Distance)
You can update a trail by time, with a range from 1 second to 9999 sec-
onds. The default is 3 seconds. You can update by distance, with a
range from 0.01 mile/nm/km to 9.99 mile/nm/km. The default is 0.10
miles. With one of the Update Criteria selected, use the cursor arrows
to highlight either the UPDATE RATE or UPDATE DISTANCE data entry boxes
and press ENT. Press ↑ or ↓ to change the first character, then press →
to the next character and repeat until the entry is correct. Press EXIT to
return to the Trail Options Menu.
Trail Options menu: Update Time Rate setting (left) and Update Dis-
tance setting (right).
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Specific Trail Options
Delete Trail
To delete a specific trail: From the Trails Menu, press ↓ to Trail
Name|ENT. The Edit Trail menu appears as seen in the following fig-
ure. Press → to DELETE TRAIL|ENT|← to YES|ENT.
Edit Trail menu.
New Trail
To manually start a new trail, in the Trails Menu, make sure NEW TRAIL
is highlighted and press ENT|EXIT.
Trail Visible/Invisible and Other Trail Options
The name, maximum number of points in the trail, activity, and visi-
bility are all changed on the Edit Trail menu screen. The Active setting
determines whether or not the unit is recording new points for a par-
ticular trail.
On the Edit Trail menu, press ↓ then → to highlight the Active and/or
Visible checkboxes. Press ENT to check (turn on) or uncheck (turn off)
the desired feature. Use ↑ ↓ or → ← to make other changes within the
Edit Trails menu. Press EXIT repeatedly to return to the main screen.
Transparency (available in some models)
Use the transparency menu to adjust the transparency of menu win-
dows. A high transparency allows you to continue monitoring the
screen's display while adjusting feature settings, though the text of the
menus may fade until it is unreadable. A low transparency will usually
make menu text easier to read at the cost of watching your display.
Experiment with this feature until you find the level of transparency
that matches your preferences.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu with Transparency command selected.
To adjust Menu Transparency level:
Press MENU|MENU|↓ to TRANSPARENCY |ENT. The TRANSPARENCY slider bar
appears. Press ↑ or ↓ to move the bar. The lower end of the scale makes
the menus opaque. The upper end is maximum transparency.
Units of Measure
This menu sets the speed and distance (statute or nautical miles, me-
ters), depth (feet, fathoms, or meters), temperature (degrees Fahrenheit
or Celsius) and heading (true or magnetic) units. To change units:
Press MENU|MENU|↓ to SYSTEM SETUP|ENT|ENT.
The Units of Measure menu.
To set Speed/Distance Unit of Measure: Press ↑ or ↓ to change the
Speed/Distance unit, then press ENT. After the option is set, press
EXIT|EXIT|EXIT to return to the page display.
To set Heading: Press ↑ or ↓ to select the heading type, then press
ENT. After the option is set, press EXIT|EXIT|EXIT to return to the page
display.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6:
Searching
NOTE:
GlobalMap HD models contain a hard drive with full map detail
built into the background map (including all of the information
available in MapCreate custom maps).
For all other units, the background map loaded in your unit lets you
search for U.S. Interstate Highway exits and exit services, as well
as some land features, including cities and lakes. For a full set of
searchable land features, including landmarks, streets, addresses
and Points of Interest, you must load your own high-detail custom
map produced with our MapCreate 6 software. For a complete de-
scription of what detail is found in the background map and custom
MapCreate maps, see page 35.
The GlobalMap's variety of search functions all begin with either the
Find Waypoint menu or the Map Page menu. Press WPT and the Find
Waypoint menu appears for waypoints and Points of Interest (POI).
From the Map Page, press MENU and the Map Page menu appears for
streets, addresses and highway exits.
Find Waypoint menu (left) and Map Page menu (right).
NOTE:
You can search for items after the unit has acquired a position, or
while using it in the "indoor" simulator mode. Distance and bearing
to the selected item will be calculated from the GlobalMap's current
position or the last known position if operating indoors or without a
position determined. You can look up items by name, or search for
the item nearest to you.
Find Addresses
1. From the Map Page, press MENU|↓ to FIND ADDRESS|ENT.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press ENT to search in the Address field.
Find Address Menu.
3. To enter an address number, press ↑ or ↓ to change the first number,
then press → to move the cursor to the next number and repeat until
the number is correct, then press ENT.
4. To enter a street name, press ↓ to STREET|ENT. There are two options:
A. You can spell out the name in the top selection box. Press ↑ or ↓ to
change the first letter, then press → to move the cursor to the next let-
ter and repeat until the name is correct, then press ENT|ENT. B. Or
jump down to the lower selection list by pressing ENT, then press ↓ or ↑
to select a street name from the list, then press ENT. The street name
you selected is now in the street field.
Find Address menu (left); Find Street menu (center) with Find By
Name field active; street name entry complete (right).
5. To enter a city name, press ↓ to CITY|ENT. You will be asked if you
want to find addresses only within a particular city. This option is de-
signed so you can limit an address search to a single city if necessary
(see the note below.)
If you select yes, there are two options: A. You can spell out the city name
in the top selection box. Press ↑ or ↓ to change the first letter, then press
→ to move the cursor to the next letter and repeat until the name is cor-
rect, then press ENT|ENT. B. Or jump down to the lower selection list by
pressing ENT, then press ↓ or ↑ to select a city name from the list, then
press ENT. The city name you selected is now in the city field.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
We recommend you do not enter a city name unless the list is too
large when searching without one. The GlobalMap can actually
search quicker without a city.
Find city field (left); Search in particular city only option (center) and
Find City by name (right).
6. When the necessary search fields are filled in, press ↓ to FIND AD-
DRESS|ENT. Your unit asks you to wait while it searches for the address.
If an address is not in the database, a message appears saying the ad-
dress could not be found.
7. The unit will display a list of addresses. If the address you are look-
ing for is highlighted at the top of the list, press ENT. If not, use ↓ and ↑
to select the correct address from the list, then press ENT. The Map
Page will appear with the location selected by the cursor. In the exam-
ple below, we are looking for 12303 East 11th Street in Tulsa, not 11th
Court, so we had to scroll down the list to select the right one.
Address search result list (left). Map Page showing
location of the address on the map, highlighted by cursor (center).
After the address is located (right) you can navigate to it.
8. To navigate to the address, press MENU|ENT|EXIT and your unit will
begin showing navigation information to the address pointed out by the
cursor. If you are only looking up an address (not navigating), just
press EXIT to return to the previous page.
Tip:
If the address happens to be an item in the Point of Interest data-
base, you can look up the item's phone number in the POI informa-
111
Download from Www.Somanuals.com. All Manuals Search And Download.
tion window. With the address location selected by the cursor on
the map, press WPT. The POI's Waypoint Information window ap-
pears, with the Go To Waypoint command highlighted. If you want
to navigate to the POI address, just press ENT|EXIT.
Map Page showing location of the address on the map, highlighted by
the cursor (left). The Address is a business in the POI database (cen-
ter), so you can display the POI information window, then navigate to
it. Address is not in the POI database (right), so the Waypoint key will
not display any information for this address.
Find Any Item Selected by Map Cursor
On the Map Page: with a POI or map feature selected by the cursor
press WPT. To return to the previous page, press EXIT.
A POI selected by the cursor (left) with POI information screen (right).
NOTE:
Since the Go To Waypoint command is highlighted, you can navi-
gate to the selected POI by pressing ENT while in the POI Waypoint
Information screen.
Find Interstate Highway Exits
1. From the Map Page, press MENU|↓ to HIGHWAY EXITS|ENT, which calls
up the Find Exit menu.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Highway Exits command (left) and Find Exit menu (right).
2. First, select a highway name by pressing ENT, which calls up the
Find By Name menu. There are two highway search options: A. You can
spell out the highway name in the top selection box. Press ↑ or ↓ to
change the first letter, then press → to move the cursor to the next let-
ter and repeat until the name is correct, then press ENT|ENT. B. Or
jump down to the lower selection list by pressing ENT, then use ↓ or ↑ to
select a highway from the list, then press ENT.
Find By Name menu.
3. Once you have selected a highway name you then can select an exit.
Press ↓ to switch to the Exit List. Press ↓ or ↑ until you highlight the
exit, then press ENT.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Exit menu, with an exit selected in the Exit List.
4. In the Exit Information screen you have two choices. A. Press ENT to
navigate or "Go To" the exit. B. Press →|ENT to find exit on the map.
Go To Exit option (left) and Find On Map option (right).
Tip:
You can also look up some additional information on the Exit Services
located near this exit. Press ↓ to SERVICES, then press ↓ or ↑ to select
Service Name|ENT.
Exit Information screen (left); general location
and amenities information (right).
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Map Places or Points of Interest (POI)
1. Press WPT, then use ↓ or ↑ to select a map place or POI category,
then press ENT. (To narrow your search, press → then press ↓ or ↑ to
select a subcategory before pressing ENT.) You will be given two op-
tions; Search By Name or By Nearest.
Find Waypoint menu with Lodging POI category selected (left) and
with the RV Parks subcategory selected (right).
2. Search by nearest POI. Press ↓|ENT. The "Find by Nearest" menu will
show a "calculating" screen, then a list of the nearest POI's will appear.
Press ↓ or ↑ to the selected POI and press ENT to call up the POI's
Waypoint Information screen.
Find by Nearest option (left) with Calculating screen (center) and POI
list (right).
3. Search by name of POI. Press ENT. There are two options: A. You can
spell out the POI in the top selection box. Press ↑ or ↓ to change the first
letter, then press → to move the cursor to the next letter and repeat
until the name is correct, then press ENT|ENT. B. Or jump down to the
lower selection list by pressing ENT, then press ↓ or ↑ to select a POI
from the list and press ENT to call up the POI's Waypoint Information
screen.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Find by Name option (left) and Find by Name menu (right).
4. When the POI's Waypoint Information screen is displayed, you can
choose to "Go To" the POI waypoint by pressing ENT or find it on the
map by pressing →|ENT.
Go To Waypoint POI option (left) and Find on Map POI option (right).
Find Streets or Intersections
Find a Street
1. From the Map Page, press MENU|↓ to FIND STREETS|ENT and the Find
Streets Menu appears.
Find Streets command (left); Find Streets menu (right).
116
Download from Www.Somanuals.com. All Manuals Search And Download.
2. You must first fill in a street name in the First Street dialog box.
Press ENT to display the Find By Name menu. There are two options: A.
You can spell out the street in the top selection box. Press ↑ or ↓ to
change the first letter, then press → to move the cursor to the next let-
ter. Repeat until the name is correct, then press ENT|ENT. B. Or you
can jump down to the lower box and pick a street from the selection list.
Press ENT, then press ↓ or ↑ to select a street from the list and press
ENT.
Find Street By Name menu. Spell out name in
the top box, or select from the list in the lower box.
3. The Find Streets menu reappears with the street you're searching for
in the First Street box. (In this example, it's 80th Street.) To search for
that street, press ↓ to FIND FIRST STREET|ENT. A message appears asking
you to wait while the unit finds the street. When the Streets Found list
appears, press ↑ or ↓ to select the street you are searching for and press
ENT.
4. The Map Page appears, with the cursor pointing to the found street.
Find Streets menu (left) with the Find First
Street command highlighted. Streets Found list (right).
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Map Page showing results of a street search.
The cursor points to the located street.
If you want to navigate to the found street at the cursor location, just
press MENU|ENT|EXIT.
Find an Intersection
You must enter one street in the First Street dialog box and enter the
next street in the Second Street dialog box.
1. From the Map Page, press MENU|↓ to FIND STREETS|ENT and the Find
Streets Menu appears.
2. You must fill in a street name in the First Street dialog box. Press ENT
to display the Find By Name menu. There are two options: A. You can
spell out the street in the top selection box. Press ↑ or ↓ to change the
first letter, then press → to move the cursor to the next letter and re-
peat until the name is correct, then press ENT|ENT. B. Or you can jump
down to the lower box and pick a street from the selection list. Press
ENT, then press ↓ or ↑ to select a street from the list and press ENT.
3. The Find Streets menu reappears with the street you're searching for
in the First Street box.
4. Now fill in the second street. Press ↓ to SECOND STREET|ENT and the
Find By Name menu appears again. Just like before, there are two op-
tions: A. You can spell out the second street in the top selection box.
Press ↑ or ↓ to change the first letter, then press → to move the cursor
to the next letter and repeat until the name is correct, then press
ENT|ENT. B. Or you can jump down to the lower box and pick the sec-
ond street from the selection list. Press ENT, then press ↓ or ↑ to select a
street from the list and press ENT.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The Find Streets menu reappears with the first and second street
dialog boxes filled in. In this example, we selected 71st Street as our
second street. You could now use similar techniques to select a city or
Zip code, but your search will probably be faster if you leave those
boxes blank. You can specify a city and/or Zip code later to narrow the
search, if the resulting list is too long.
Find Intersection command highlighted (left) and
Working message (center). The Intersections Found list (right).
6. To search for the intersection of the two streets, press ↓ to FIND IN-
TERSECTION|ENT.
Use the arrow keys to select FIND INTERSECTION then press ENT. A message
appears asking you to wait while the unit finds the intersection. When
the Intersections Found list appears, press ↑ or ↓ to select the intersec-
tion you are searching for and press ENT. A window will appear
prompting you to FIND or GO TO. In this example, we chose FIND. (In the
example on the previous page, we selected the intersection of SW 80th
Street and SW 71st Avenue in Miami, Fla.)
7. The Map Page appears, with the cursor pointing to the found inter-
section. The intersection in our example is shown below.
Map Page showing results of an intersection search.
The cursor points to the located intersection.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
If you want to navigate to the found intersection, just press
MENU|ENT|EXIT.
Find Waypoints
1. Press WPT|ENT.
2. If searching for the waypoint By Name, press ENT. If searching for
the Nearest waypoint, press ↓ to NEAREST|ENT. (To search by name,
jump to step 5 below.)
Find Waypoint menu (left), Find By Nearest command (center) and
Find by Name command (right).
3. If you're looking for nearest waypoint, the GlobalMap says it is calcu-
lating, then a list of waypoints appears. The closest waypoint is high-
lighted at the top of the list and the one farthest from you is at the bot-
tom of the list.
Calculating message (left) and list of nearest waypoints (right).
4. To see location information on the closest (highlighted) waypoint,
press ENT and the Waypoint Information screen appears. (If you
wanted to, you could select another waypoint from the list with the ↑ or
↓ keys.)
A. To navigate to the waypoint, press ENT. (The Go To Waypoint
command is already highlighted.) The unit will show navigation in-
formation to the waypoint.
B. To find the waypoint, press ↓ to FIND ON MAP|ENT. The Map Page
appears with the cursor centered on the found waypoint.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Waypoint Information screens with the Go To Waypoint command se-
lected (left) and the Find on Map command selected (right).
To clear these menus and return to the previous page, press EXIT re-
peatedly.
5. If you're looking by name, there are two options: A. You can spell out
the name in the top selection box. Press ↑ or ↓ to change the first letter,
then press → to move the cursor to the next letter and repeat until the
name is correct, then press ENT|ENT. B. Or you can jump down to the
lower selection list by pressing ENT, then press ↓ or ↑ to select a way-
point from the list and press ENT. The waypoint information screen ap-
pears.
Find By Name menu (left). Waypoint Information screen (center). The
found waypoint (right) is highlighted by the cursor on the Map Page.
A. To navigate to the waypoint, press ENT. (Go To Waypoint com-
mand is already highlighted.) The unit will show navigation infor-
mation to the waypoint.
B. To find the waypoint, press ↓ to FIND ON MAP|ENT. The Map Page
appears with the cursor centered on the found waypoint.
To clear these menus and return to the previous page, press EXIT re-
peatedly.
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Supplemental Material
Datums Used by This Unit
WGS 1984
Default
Zaire, Zambia and
Zimbabwe
Australian Geodetic
1984 - Australia &
Tasmania
Adindan
Mean for Ethiopia,
Sudan
Arc 1950 - Botswana
Arc 1950 - Burundi
Arc 1950 - Lesotho
Arc 1950 - Malawi
Arc 1950 - Swaziland
Arc 1950 - Zaire
Ayabelle Lighthouse -
Djibouti
Adindan
Burkina Faso
Bellevue (IGN) -
Efate & Erromango
Islands
Adindan
Cameroon
Bermuda 1957 -
Bermuda
Adindan
Ethiopia
Bissau - Guinea-
Bissau
Bogota Observatory -
Colombia
Arc 1950 - Zambia
Arc 1950 - Zimbabwe
Adindan
Mali
Adindan
Senegal
Arc 1960 - Mean for
Kenya, Tanzania
Bukit Rimpah - Indo-
nesia (Bangka & Be-
litung Islands)
Adindan
Sudan
Ascension Island
1958 - Ascension
Island
Camp Area Astro -
Antarctica (McMurdo
Camp Area)
Afgooye
Somalia
Astro Beacon E 1945
- Iwo Jima
Campo Inchauspe -
Argentina
Ain el Abd 1970
Bahrain
Astro DOS 71/4 - St.
Helena Island
Canton Astro 1966 -
Phoenix Islands
Ain el Abd 1970
Saudi Arabia
Astro Tern Island
(FRIG) 1961 - Tern
Island
Cape - South Africa
Anna 1 Astro 1965
Cocos Islands
Cape Canaveral -
Bahamas, Florida
Astronomical Station
1952 - Marcus Island
Antigua Island Astro
1943; Antigua (Lee-
ward Islands)
Carthage - Tunisia
Switzerland
Australian Geodetic
1966 - Australia &
Tasmania
Arc 1950; Mean for
Botswana, Lesotho,
Malawi, Swaziland,
Chatham Island Astro
1971; New Zealand
(Chatham Island)
123
Download from Www.Somanuals.com. All Manuals Search And Download.
European 1950
England, Channel
Islands, Ireland,
Scotland, Shetland
Islands
L.C. 5 Astro 1961
Cayman Brac Island
Chua Astro
Paraguay
Leigon
Ghana
Corrego Alegre
Brazil
European 1950
Finland, Norway
Liberia 1964
Liberia
Dabola
Guinea
European 1950
Greece
Luzon
Philippines (Exclud-
ing Mindanao)
Djakarta (Batavia)
Indonesia (Sumatra)
European 1950
Iran
DOS 1968
New Georgia Islands
(Gizo Island)
Luzon
Philippines (Min-
danao)
European 1950
Italy (Sardinia)
Easter Island 1967
Easter Island
Mahe 1971
Mahe Island
European 1950
(Sicily)
European 1950
European 1950
Malta
Massawa
Ethiopia (Eritrea)
Mean for Austria,
Belgium, Denmark,
Finland, France,
West Germany, Gi-
braltar, Greece, Italy,
Luxembourg, Neth-
erlands, Norway,
Portugal, Spain,
Ireland 1965
Ireland
Merchich
Morocco
ISTS 061 Astro 1968
South Georgia Is-
lands
Midway Astro 1961
Midway Islands
Sweden, Switzerland
Minna
Cameroon
ISTS 073 Astro 1969
Diego Garcia
European 1950
Mean for Austria,
Denmark, France,
West Germany,
Netherlands, Swit-
zerland
Minna
Nigeria
Johnston Island 1961
Johnston Island
Montserrat Island
Astro 1958; Montser-
rat (Leeward Islands)
Kandawala
Sri Lanka
European 1950
Mean for Iraq, Israel,
Jordan, Lebanon,
Kuwait, Saudi Arabia,
Syria
Kerguelen Island
1949
Kerguelen Island
M’Poraloko
Gabon, Nahrwan,
Oman (Masirah Is-
land)
Kertau 1948
West Malaysia &
Singapore
European 1950
Cyprus
Nahrwan
Saudi Arabia
European 1950
Egypt
Kusaie Astro 1951
Caroline Islands
Nahrwan
United Arab Emirates
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Naparima BWI
Trinidad & Tobago
North American 1927
Canada (Alberta,
British Columbia)
Old Hawaiian
Mean for Hawaii,
Kauai, Maui, Oahu
North American 1927
Mean for Antigua,
Barbados, Barbuda,
Caicos Islands,
Cuba, Dominican
Republic, Grand
Cayman, Jamaica,
Turks Islands
North American 1927
Canada (Manitoba,
Ontario)
Old Hawaiian
Hawaii
Old Hawaiian
Kauai
North American 1927
Canada (New
Brunswick, New-
foundland, Nova
Scotia, Quebec)
Old Hawaiian
Maui
North American 1927
Mean for Belize,
Costa Rica, El Sal-
vador, Guatemala,
Honduras, Nicaragua
Old Hawaiian
Oahu
North American 1927
Canada (Northwest
Territories, Sas-
katchewan)
Oman
Oman
North American 1927
Mean for Canada
North American 1927
Canada (Yukon)
Ordinance Survey
Great Britain 1936 -
Mean for England,
Isle of Man, Scotland,
Shetland Islands,
Wales
North American 1927
Mean for CONUS
(Continental United
States)
North American 1927
Canal Zone
North American 1927
Mean for CONUS
(East of Mississippi
River) including Lou-
isiana, Missouri, Min-
nesota
North American 1927
Cuba
Ordinance Survey
Great Britain 1936 -
England
North American 1927
Greenland (Hayes
Peninsula)
Ordinance Survey
Great Britain 1936 -
England, Isle of Man,
Wales
North American 1927
Mean for CONUS
(West of Mississippi
River)
North American 1927
Mexico
North American 1983
Alaska, Canada,
CONUS
Ordinance Survey
Great Britain 1936 -
Scotland, Shetland
Islands
North American 1927
Alaska
North American 1983
Central America,
Mexico
North American 1927
Bahamas (Except
San Salvador Island)
Ordinance Survey
Great Britain 1936 -
Wales
Observaorio Metereo
1939; Azores (Corvo
& Flores Islands)
North American 1927
Bahamas (San Sal-
vador Island)
Pico de las Nieves
Canary Islands
Old Egyptian 1907
Egypt
Pitcairn Astro 1967
Pitcairn Island
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Point 58
Sweden
Tokyo
Mean for Japan, Ko-
rea, Okinawa
South American 1969
Chile
Santo (DOS)
1965 Espirito Santo
Island
South American 1969
Colombia
Tokyo
Japan
South American 1969
Ecuador
Tokyo
Korea
Sao Braz
Azores (Sao Miguel,
Santa Maria Islands)
South American 1969
Ecuador (Baltra, Ga-
lapagos)
Tokyo
Sapper Hill 1943
Okinawa
East Falkland Island
South American 1969
Guyana
Tristan Astro 1968
Tristan da Cunha
Schwarzeck
Nambia
South American 1969
Paraguay
South American 1969
Peru
Viti Levu 1916
Fiji (Viti Levu Island)
Selvagem Grande
Salvage Islands
Wake
SGS 85
Soviet Geodetic
System 1985
South American 1969
Trinidad & Tobago
Eniwetok 1960
Marshall Islands
South American 1969
Mean for Argentina,
Bolivia, Brazil, Chile,
Colombia, Ecuador,
Guyana, Paraguay,
Peru, Trinidad & To-
bago, and Venezuela
South American 1969
Venezuela
Wake Island Astro
1952
Wake Atoll
South Asia
Singapore
WGS 1972
Global Definition
Tananarive Obser-
vatory 1925; Mada-
gascar
South American 1969
Argentina
Yacare
Uruguay
South American 1969
Bolivia
Timbalai 1948
Brunei, East Malay-
sia (Sabah, Sarawak)
Zanderij
Suriname
South American 1969
Brazil
126
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Compliance
This device complies with Part 15 of the U.S. Federal Communi-
cations Commission (FCC) Rules. Operation is subject to the fol-
lowing two conditions: (1) this device may not cause harmful in-
terference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired opera-
tion.
Changes or modifications not expressly approved by the manu-
facturer could void the user's authority to operate the equip-
ment.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the factory customer service department for help.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
128
Download from Www.Somanuals.com. All Manuals Search And Download.
LOWRANCE DATABASES LICENSE AGREEMENT
THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST
PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL,
FAMILY, OR HOUSEHOLD USE ("YOU") AND LOWRANCE ELECTRONICS,
INC., THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US").
USING THE PRODUCT ACCOMPANIED BY THIS LICENSE AGREEMENT
CONSTITUTES ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF
YOU DO NOT ACCEPT ALL TERMS AND CONDITIONS, PROMPTLY RE-
TURN THE PRODUCT WITHIN 30 DAYS OF PURCHASE. PLEASE RE-
TURN USING THE ENCLOSED UPS SHIPPING LABEL AND INCLUDE:
PROOF OF PURCHASE, NAME, ADDRESS, AND PHONE NUMBER. YOUR
PURCHASE PRICE AND ANY APPLICABLE TAXES WILL BE REFUNDED.
PLEASE ALLOW 4-6 WEEKS TO PROCESS YOUR REFUND.
1. This License Agreement applies to the one or more databases that
your product may contain. We refer to these singly as a "Database"
and together as the "Databases." Your product may thus include the
"WBS Database" which contains worldwide background surface
mapping data, the "SmartMap Database" which contains inland
mapping data, or other Databases.
2. The Databases that your product may contain are licensed, not sold.
We grant to you the nonexclusive, nonassignable right to use these
Databases for supplemental navigation reference purposes, but only
as long as you comply with the terms and conditions of this License
Agreement. We reserve the right to terminate this license if you
violate any aspect of this License Agreement. You are responsible for
using official government charts and prudent navigation for safe
travel.
3. The Databases housed in your product are protected by the copy-
right notices appearing on the product or its screen(s). You may
NOT modify, adapt, translate, reverse engineer, decompile, disas-
semble, rent, lease, or resell any Database, and you may NOT create
derivative works based upon any Database or its contents. Any un-
authorized reproduction, use, or transfer of a Database may be a
crime and may subject you to damages and attorney fees.
4. This License Agreement will terminate immediately without prior
notice from us if you fail to comply with or violate any of the provi-
sions of this Agreement. Upon termination, you will promptly return
all products containing one or more Databases to us.
5. Prices and programs are subject to change without notice.
6. This License Agreement shall be governed by the laws of the State of
Oklahoma and comprises the complete and exclusive understanding
between you and us concerning the above subject matter.
129
Download from Www.Somanuals.com. All Manuals Search And Download.
DATABASES LIMITED WARRANTY
"We", "our", or "us" refers to Lowrance Electronics, Inc., the manufacturer of
this product. "You" or "your" refers to the first person who purchases the prod-
uct as a consumer item for personal, family, or household use. The Databases
Limited Warranty applies to the one or more databases that your product may
contain. We refer to each of these as a "Database" or together as the "Data-
bases." Your product may thus include the "WBS Database" which contains
worldwide background surface mapping data, the "SmartMap Database" which
contains inland mapping data, or other Databases.
We warrant to you that we have accurately compiled, processed, and repro-
duced the portions of the source material on which the Databases are based.
However, we are under no obligation to provide updates to the Databases, and
the data contained in the Databases may be incomplete when compared to the
source material. WE MAKE NO EXPRESS OR IMPLIED WARRANTY OF
ANY KIND ABOUT THE ACCURACY OF THE SOURCE MATERIAL ITSELF,
INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If there is a defect in any Database, your exclusive remedy shall be, at our op-
tion, either a refund of the price you paid for the product containing the defec-
tive Database or a replacement of such product. WE WILL NOT UNDER ANY
CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSE-
QUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF ANY KIND.
Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages, so the above limitations or exclusions may not apply to you.
This warranty does NOT apply in the following circumstances: (1) when the
product has been serviced or repaired by anyone other than us; (2) when the
product has been connected, installed, combined, altered, adjusted, or handled
in a manner other than according to the instructions furnished with the prod-
uct; (3) when any serial number has been effaced, altered, or removed; or (4)
when any defect, problem, loss, or damage has resulted from any accident, mis-
use, negligence, or carelessness, or from any failure to provide reasonable and
necessary maintenance in accordance with the instructions of the owner’s man-
ual for the product.
We reserve the right to make changes or improvements in our products from
time to time without incurring the obligation to install such improvements or
changes on equipment or items previously manufactured.
This warranty gives you specific legal rights and you may also have other rights
which may vary from state to state.
Your remedies under this warranty will be available so long as you can show in
a reasonable manner that the defect occurred within one (1) year from the date
of your original purchase, and we must receive your warranty claim no later
than 30 days after such 1-year period expires. Your claim must be substanti-
ated by a dated sales receipt or sales slip.
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
132
Download from Www.Somanuals.com. All Manuals Search And Download.
LOWRANCE ELECTRONICS
FULL ONE-YEAR WARRANTY
"We," "our," or "us" refers to LOWRANCE ELECTRONICS, INC., the manufacturer of
this product. "You" or "your" refers to the first person who purchases this product as a
consumer item for personal, family or household use.
We warrant this product against defects or malfunctions in materials and workmanship,
and against failure to conform to this product's written specifications, all for one (1) year
from the date of original purchase by you. WE MAKE NO OTHER EXPRESS WAR-
RANTY OR REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING THIS
PRODUCT. Your remedies under this warranty will be available so long as you can show
in a reasonable manner that any defect or malfunction in materials or workmanship, or
any non-conformity with the product's written specifications, occurred within one year
from the date of your original purchase, which must be substantiated by a dated sales
receipt or sales slip. Any such defect, malfunction, or non-conformity which occurs within
one year from your original purchase date will either be repaired without charge or be
replaced with a new product identical or reasonably equivalent to this product, at our
option, within a reasonable time after our receipt of the product. If such defect, malfunc-
tion, or non-conformity remains after a reasonable number of attempts to repair by us,
you may elect to obtain without charge a replacement of the product or a refund for the
product. THIS REPAIR, OR REPLACEMENT OR REFUND (AS JUST DESCRIBED) IS
THE EXCLUSIVE REMEDY AVAILABLE TO YOU AGAINST US FOR ANY DEFECT,
MALFUNCTION, OR NON-CONFORMITY CONCERNING THE PRODUCT OR FOR
ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER CAUSE WHATSOEVER.
WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY
SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF
ANY KIND.
Some states do not allow the exclusion or limitation of incidental or consequential dam-
ages, so the above limitations or exclusions may not apply to you.
This warranty does NOT apply in the following circumstances: (1) when the product has
been serviced or repaired by anyone other than us; (2) when the product has been con-
nected, installed, combined, altered, adjusted, or handled in a manner other than ac-
cording to the instructions furnished with the product; (3) when any serial number has
been effaced, altered, or removed; or (4) when any defect, problem, loss, or damage has
resulted from any accident, misuse, negligence, or carelessness, or from any failure to
provide reasonable and necessary maintenance in accordance with the instructions of the
owner's manual for the product.
We reserve the right to make changes or improvements in our products from time to time
without incurring the obligation to install such improvements or changes on equipment
or items previously manufactured.
This warranty gives you specific legal rights and you may also have other rights which
may vary from state to state.
REMINDER: You must retain the sales slip or sales receipt proving the date of your
original purchase in case warranty service is ever required.
LOWRANCE ELECTRONICS
12000 E. SKELLY DRIVE, TULSA, OK 74128
(800) 324-1356
133
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Obtain Service…
…in the USA:
We back your investment in quality products with quick, expert service
and genuine Lowrance parts. If you're in the United States and you
have technical, return or repair questions, please contact the Factory
Customer Service Department. Before any product can be returned, you
must call customer service to determine if a return is necessary. Many
times, customer service can resolve your problem over the phone with-
out sending your product to the factory. To call us, use the following
toll-free number:
800-324-1356
8 a.m. to 5 p.m. Central Standard Time, M-F
Lowrance Electronics may find it necessary to change or end our ship-
ping policies, regulations, and special offers at any time. We reserve the
right to do so without notice.
…in Canada:
If you're in Canada and you have technical, return or repair questions,
please contact the Factory Customer Service Department. Before any
product can be returned, you must call customer service to determine if
a return is necessary. Many times, customer service can resolve your
problem over the phone without sending your product to the factory. To
call us, use the following toll-free number:
800-661-3983
905-629-1614 (not toll-free)
8 a.m. to 5 p.m. Eastern Standard Time, M-F
…outside Canada and the USA:
If you have technical, return or repair questions, contact the dealer in
the country where you purchased your unit. To locate a dealer near
you, visit our web site, www.lowrance.com and look for the Dealer Lo-
cator.
134
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessory Ordering Information
for all countries
To order Lowrance accessories such as power cables or antennas, please
contact:
1) Your local marine dealer or consumer electronics store. Most quality
dealers that handle marine electronic equipment or other consumer
electronics should be able to assist you with these items.
To locate
a
Lowrance dealer near you, visit our web site,
www.lowrance.com and look for the Dealer Locator. Or, you can consult
your telephone directory for listings.
2) U.S. customers: LEI Extras Inc., PO Box 129, Catoosa, OK 74015-0129
Call 1-800-324-0045 or visit our web site www.lei-extras.com.
3) Canadian customers can write:
Lowrance/Eagle Canada, 919 Matheson Blvd. E. Mississauga, Ontario
L4W2R7 or fax 905-629-3118.
Shipping Information
If it becomes necessary to send a product for repair or replacement, you
must first receive a return authorization number from Customer
Service. Products shipped without a return authorization will not be
accepted. When shipping, we recommend you do the following:
1. Please do not ship the knobs or mounting bracket with your unit.
2. If you are sending a check for repair, please place your check in an
envelope and tape it to the unit.
3. For proper testing, include a brief note with the product describing
the problem. Be sure to include your name, return shipping address
and a daytime telephone number. An e-mail address is optional but
useful.
4. Pack the unit in a suitable size box with packing material to prevent
any damage during shipping.
5. Write the Return Authorization (RA) number on the outside of the
box underneath your return address.
6. For your security, you may want to insure the package through your
shipping courier. Lowrance does not assume responsibility for goods
lost or damaged in transit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Visit our web site:
Lowrance Pub. 988-0151-331
Printed in USA 030705
© Copyright 2005
All Rights Reserved
Lowrance Electronics, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|