ADSL Modem
User Guide
WIRED
Model No.
AM200 (EU/LA)
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Table of Contents
Chapter 1: Introduction
Welcome
1
1
What’s in this Guide?
2
Chapter 2: Getting to Know the ADSL Modem
The Back Panel
3
3
4
The Front Panel
Chapter 3: Setting Up and Connecting the ADSL Modem
Overview
5
5
5
Wall-Mount Option
Connecting the Modem
5
Chapter 4: Configuring the ADSL Modem
Overview
7
7
9
9
How to Access the Web-based Utility
The Setup Tab
The Security Tab
The Applications and Gaming Tab
The Administration Tab
15
18
20
24
25
25
28
30
The Status Tab
Appendix A: Troubleshooting
Common Problems and Solutions
Frequently Asked Questions
Appendix B: Upgrading Firmware
Appendix D: Specifications
Appendix E: Warranty Information
Appendix F: Regulatory Information
Appendix G: Contact Information
31
36
37
38
44
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
List of Figures
Figure 2-1: Back Panel
3
4
Figure 2-2: Front Panel
Figure 3-1: Wall-Mount Option
Figure 3-2: DSL Connection
Figure 3-3: Ethernet Connection
Figure 3-4: Power Connection
Figure 4-1: Password Screen
Figure 4-2: Basic Setup Tab
Figure 4-3: Dynamic IP
5
5
6
6
9
9
10
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
19
Figure 4-4: Static IP
Figure 4-5: RFC Routed
Figure 4-6: RFC 2516 PPPoE
Figure 4-7: RFC 2364 PPPoA
Figure 4-8: Bridged Mode Only
Figure 4-9: Network Setup
Figure 4-10: DynDNS.org
Figure 4-11: TZO.com
Figure 4-12: Advanced Routing
Figure 4-13: Routing Table
Figure 4-14: Firewall
Figure 4-15: Access Control
Figure 4-16: Edit Schedule Rule
Figure 4-17: MAC Filtering
Figure 4-18: URL Blocking
Figure 4-19: Intrusion Detection
Figure 4-20: VPN Passthrough
Figure 4-21: Port Range Forwarding
Figure 4-22: Port Triggering
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Figure 4-23: NAT Mapping Table
Figure 4-24: DMZ
Figure 4-25: Management
Figure 4-26: SNMP
19
19
20
20
21
21
21
22
22
22
23
23
23
24
24
24
30
Figure 4-27: Log
Figure 4-28: Incoming Log
Figure 4-29: Outgoing Log
Figure 4-30: Diagnostic Tests
Figure 4-31: Ping Test
Figure 4-32: Traceroute Test
Figure 4-33: Firmware Upgrade
Figure 4-34: Factory Defaults
Figure 4-35: Reboot
Figure 4-36: Status
Figure 4-37: Local Network
Figure 4-38: DHCP Clients Table
Figure B-1: Upgrade Firmware
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Chapter 1: Introduction
Welcome
Thank you for choosing the ADSL Modem. The Linksys ADSL Modem gives you an instant, high-speed connection
to the Internet. ADSL technology lets you access the Internet using your existing phone lines, without interfering
with your voice phone service. You can talk on the phone and surf the net at the same time. Web surfing and your
e-mail are instantly available, anytime.
Installation is quick and simple. Connect it directly to any PC with an available Ethernet port, and you’re ready to
surf the Internet. Or connect it to a Linksys router and share that high-speed Internet access with everyone on
your home network.
Use the instructions in this user guide to help you connect the ADSL Modem and configure it to access the
Internet. These instructions should be all you need to get the most out of the ADSL Modem.
Chapter 1: Introduction
Welcome
1
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
What’s in this Guide?
This user guide covers the steps for setting up and using the ADSL Modem.
•
•
•
•
•
Chapter 1: Introduction
This chapter describes the ADSL Modem applications and this User Guide.
Chapter 2: Getting to Know the ADSL Modem
This chapter describes the physical features of the ADSL Modem.
Chapter 3: Connecting the ADSL Modem
This chapter instructs you on how to connect the ADSL Modem to your network.
Chapter 4: Configuring the ADSL Modem
This chapter explains how to use the Web-Based Utility to configure the settings on the ADSL Modem.
Appendix A: Troubleshooting
This appendix describes some problems and solutions, as well as frequently asked questions, regarding
installation and use of the ADSL Modem.
•
Appendix B: Upgrading Firmware
This appendix instructs you on how to upgrade the firmware on your ADSL Modem if you should need to do
so.
•
•
•
•
•
Appendix C: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
Appendix D: Specifications
This appendix provides the technical specifications for the ADSL Modem.
Appendix E: Warranty Information
This appendix supplies the warranty information for the ADSL Modem.
Appendix F: Regulatory Information
This appendix supplies the regulatory information regarding the ADSL Modem.
Appendix G: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Chapter 1: Introduction
What’s in this Guide?
2
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Chapter 2: Getting to Know the ADSL Modem
The Back Panel
The Modem’s ports, where cables are connected, are located on the back panel. The Modem’s reset button is also
located on the back panel.
Figure 2-1: Back Panel
Important: Resetting the Modem to factory
defaults will erase all of your settings (WAN
and LAN settings, etc.) and replace them with
the factory defaults. Do not reset the Modem if
you want to retain these settings.
DSL
The DSL port connects to the DSL line.
Ethernet
Reset Button
The Ethernet port connects to your computer and other network devices.
There are two ways to reset the Modem's factory default settings. Either press the Reset
Button, for approximately ten seconds, or restore the defaults on the Factory Defaults screen
of the Administration tab in the Modem’s Web-Based Utility.
Power
The Power port is where you connect the power adapter.
With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys
Modem.
Chapter 2: Getting to Know the ADSL Modem
The Back Panel
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
The Front Panel
The Modem's LEDs, where information about network activity is displayed, are located on the front panel.
Figure 2-2: Front Panel
Power
Green. The Power LED lights up when the Modem is powered on.
Ethernet
Green. The Ethernet LED serves two purposes. If the LED is continuously lit, the Modem is
successfully connected to a device through the Ethernet port. If the LED is blinking, it is an
indication of any network activity.
DSL
Green. The DSL LED lights up whenever there is a successful DSL connection. The LED blinks
while establishing the DSL connection.
Internet
Green. The Internet LED lights up green when an Internet connection to the Internet Service
Provider (ISP) session is established. The Internet LED lights up red when the connection to
the ISP fails.
Chapter 2: Getting to Know the ADSL Modem
The Front Panel
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Chapter 3: Setting Up and Connecting the ADSL Modem
Overview
In this chapter, you will connect the Modem to your DSL line and to a computer in your home or business. It is not
necessary to mount your Modem, but may be useful to conserve space. There are 2 slots on the underside of the
Modem that can be used for wall mounting.
Wall-Mount Option
You will need 2 suitable screws (4.4 mm screw diameter) to mount the Modem.
1. Determine where you want to mount the Modem. Ensure that the wall you use is smooth, flat, dry and sturdy
and make sure the location is within reach of the power outlet.
2. Drill two holes into the wall. Make sure the holes are 101.6 mm (4 inches) apart.
3. Insert a screw into each hole, and leave 3 mm (0.12 inch) of its head exposed.
4. Maneuver the Modem so the wall-mount slots line up with the two screws.
5. Place the wall-mount slots over the screws and slide the Modem down until the screws fit snugly into the
wall-mount slots.
101.6 mm (4 inches)
Figure 3-1: Wall-Mount Option
Congratulations! The Wall-Mount installation of the Modem is complete. Perform the steps under Connecting the
Modem to complete your Modem installation.
Connecting the Modem
1. Connect one end of the provided phone cable to the DSL (RJ-11 phone) port that is on the back of your
Modem. Connect the other end of the phone cable to the wall jack with DSL service.
NOTE: A small device called a microfilter (not included) may be necessary between each phone
and wall jack to prevent interference. Contact your ISP if you have any questions.
Figure 3-2: DSL Connection
Chapter 3: Setting Up and Connecting the ADSL Modem
Overview
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
IMPORTANT: For countries that have phone jacks with RJ-11 connectors, make sure to only place
the microfilters between the phone and the wall jack and not between the Modem and the wall
jack or your DSL will not connect.
For countries that do not have phone jacks with RJ-11 connectors (e.g. France, Sweden,
Switzerland, United Kingdom, etc.), except for ISDN users, the microfilter has to be used between
the modem and the wall jack, because the microfilter will have the RJ-11 connector.
2. Connect one end of the provided Ethernet cable to your PC’s Ethernet port. Connect the other end of the
cable to the Ethernet port on the back of your Modem.
Figure 3-3: Ethernet Connection
3. Connect the power adapter to your Modem and to the electrical outlet.
NOTE: You should always plug the Modem’s power adapter into a power strip
with surge protection.
4. Turn on your PC.
The connection of the Modem is complete.
Figure 3-4: Power Connection
Chapter 3: Setting Up and Connecting the ADSL Modem
Connecting the Modem
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Chapter 4: Configuring the ADSL Modem
Overview
Follow the steps in this chapter and use the Modem’s web-based utility to configure the Modem. This chapter will
describe each web page in the Utility and each page’s key functions. The utility can be accessed via your web
browser through use of a computer connected to the Modem. For a basic network setup, most users only have to
use the following screens of the Utility:
Have You: Enabled TCP/IP on your computers?
computers communicate over the network with
this protocol. Refer to Windows Help for more
information on TCP/IP.
•
•
Basic Setup. On the Basic Setup screen, enter the settings provided by your ISP.
Note: For added security, you should change
the password through the Administration tab.
Management. Click the Administration tab and then the Management tab. The Modem’s default username
and password is admin. To secure the Modem, change the Password from its default.
There are five main tabs: Setup, Security, Applications & Gaming, Administration, and Status. Additional tabs will
be available after you click one of the main tabs.
Setup
•
•
Basic Setup. Enter the Internet connection and network settings on this screen.
DDNS. To enable the Modem’s Dynamic Domain Name System (DDNS) feature, complete the fields on this
screen.
•
Advanced Routing. On this screen, you can alter Dynamic Routing, and Static Routing configurations.
Security
•
Firewall. This screen contains Filters and Block WAN Requests. Filters block specific internal users from
accessing the Internet and block anonymous Internet requests.
•
VPN. To enable or disable IPSec and/or PPTP Pass-through, use this screen.
Applications & Gaming
•
Port Range Forwarding. To set up public services or other specialized Internet applications on your network,
click this tab.
Chapter 4: Configuring the ADSL Modem
Overview
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
•
•
•
Port Triggering. To set up triggered ranges and forwarded ranges for Internet applications, click this tab.
NAT Mapping Table. This table displays the current NAPT address mappings.
DMZ. To allow one local user to be exposed to the Internet for use of special-purpose services, use this
screen.
Administration
•
•
•
•
•
•
•
Management. On this screen, alter Modem access privileges, SNMP, UPnP, and WT-82 settings.
SNMP. Use this screen to configure SNMP manager access.
Log. If you want to view or save activity logs, click this tab.
Diagnostics. Use this screen to do a Ping Test or Traceroute Test.
Firmware Upgrade. Click this tab if you want to upgrade the Modem’s firmware.
Factory Defaults. If you want to restore the Modem’s factory defaults, use this screen.
Reboot. This tab allows you to do a hard reboot of your Modem.
Status
•
•
Modem. This screen provides status information about the Modem.
Local Network. This provides status information about the local network.
Chapter 4: Configuring the ADSL Modem
Overview
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
How to Access the Web-based Utility
To access the web-based utility, launch Internet Explorer or Netscape Navigator, and enter the Modem’s default IP
address, 192.168.1.1, in the Address field. Then press Enter.
A Log In screen appears. Enter admin (the default user name) in the Username field, and enter admin (the
default password) in the Password field. Then click the Login button.
Figure 4-1: Password Screen
The Setup Tab
Basic Setup
The first screen that appears is the Basic Setup tab. This tab allows you to change the Modem's general settings.
Change these settings as described here and click the Save Settings button to save your changes, or click the
Cancel Changes button to cancel your changes.
Internet Setup
ADSL Settings
•
Encapsulation. The Modem supports five Encapsulation methods: RFC 1483 Bridged, RFC 1483 Routed, RFC
2516 PPPoE, RFC 2364 PPPoA, and Bridged Mode Only. Select the appropriate type of encapsulation from the
drop-down menu. The Basic Setup screen and available features will vary depending on what type of
encapsulation you select.
•
Virtual Circuit ID. These fields consist of two items: VPI (Virtual Path Identifier) and VCI (Virtual Channel
Identifier). Your ISP will provide the correct settings for these fields.
•
•
Multiplexing. Select LLC or VC, depending on your ISP.
DSL Modulation. Select a type from the drop-down menu: Auto, T1.413i2, G.992.1 (G.DMT),
G.992.2 (G.Lite), G.922.3(ADSL2), G.992.5(ADSL2+)
Figure 4-2: Basic Setup Tab
Chapter 4: Configuring the ADSL Modem
How to Access the Web-based Utility
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
RFC 1483 Bridged
Dynamic IP
IP Settings. Select Obtain an IP Address Automatically if your ISP says you are connecting through a
dynamic IP address.
Static IP
Figure 4-3: Dynamic IP
If you are required to use a permanent (static) IP address to connect to the Internet, then select Use the
following IP Address.
•
IP Address. This is the Modem’s IP address, when seen from the WAN, or the Internet. Your ISP will
provide you with the IP Address you need to specify here.
•
•
Subnet Mask. This is the Modem’s Subnet Mask. Your ISP will provide you with the Subnet Mask.
Default Gateway. Your ISP will provide you with the default Gateway Address, which is the ISP server’s IP
address.
•
Primary DNS (Required) and Secondary DNS (Optional). Your ISP will provide you with at least one DNS
(Domain Name System) Server IP Address.
Figure 4-4: Static IP
RFC 1483 Routed
If you are required to use RFC 1483 Routed, then select RFC 1483 Routed. Select Obtain IP Address
Automatically (DHCP) or Set Static IP Manually. If you select Set Static IP Manually, enter the information
below.
•
Internet IP Address. This is the Modem’s IP address, when seen from the WAN, or the Internet. Your ISP
will provide you with the IP Address you need to specify here.
•
•
Subnet Mask. This is the Modem’s Subnet Mask. Your ISP will provide you with the Subnet Mask.
Default Gateway. Your ISP will provide you with the default Gateway Address, which is the ISP server’s IP
address.
•
Primary DNS (Required) and Secondary DNS (Optional). Your ISP will provide you with at least one DNS
(Domain Name System) Server IP Address.
Figure 4-5: RFC Routed
Chapter 4: Configuring the ADSL Modem
The Setup Tab
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
RFC 2516 PPPoE
Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections. If
you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do,
you will have to enable PPPoE.
•
•
User Name and Password. Enter the User Name and Password provided by your ISP.
Keep Alive: Redial Period. If you select this option, the Modem will periodically check your Internet
connection. If you are disconnected, then the Modem will automatically re-establish your connection. To
use this option, click the Keep Alive radio button. In the Redial Period field, specify how often you want
the Modem to check the Internet connection. The default Redial Period is 3 minutes.
•
Connect on Demand: Max Idle Time. You can configure the Modem to disconnect the Internet connection
after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has
been terminated due to inactivity, Connect on Demand enables the Modem to automatically re-establish
your connection as soon as you attempt to access the Internet again. To use this option, click the Connect
on Demand radio button. In the Max Idle Time field, enter the number of minutes you want to have
elapsed before your Internet connection terminates.
Figure 4-6: RFC 2516 PPPoE
RFC 2364 PPPoA
Some DSL-based ISPs use PPPoA (Point-to-Point Protocol over ATM) to establish Internet connections. If you
are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoA. If they do, you
will have to enable PPPoA.
•
•
User Name and Password. Enter the User Name and Password provided by your ISP.
Keep Alive: Redial Period. If you select this option, the Modem will periodically check your Internet
connection. If you are disconnected, then the Modem will automatically re-establish your connection. To
use this option, click the Keep Alive radio button. In the Redial Period field, specify how often you want
the Modem to check the Internet connection. The default Redial Period is 3 minutes.
•
Connect on Demand: Max Idle Time. You can configure the Modem to disconnect the Internet connection
after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has
been terminated due to inactivity, Connect on Demand enables the Modem to automatically re-establish
your connection as soon as you attempt to access the Internet again. To use this option, click the Connect
on Demand radio button. In the Max Idle Time field, enter the number of minutes you want to have
elapsed before your Internet connection terminates.
Figure 4-7: RFC 2364 PPPoA
Chapter 4: Configuring the ADSL Modem
The Setup Tab
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Bridged Mode Only
If you are using your Modem as a bridge, which makes the Modem act like a stand-alone modem, select
Bridged Mode Only. All NAT and routing settings are disabled in this mode.
Optional Settings (required by some ISPs)
Figure 4-8: Bridged Mode Only
•
Host Name and Domain Name. These fields allow you to supply a host and domain name for the Modem.
Some ISPs require these names as identification. You may have to check with your ISP to see if your
broadband Internet service has been configured with a host and domain name. In most cases, you can leave
these fields blank.
Network Setup
•
Modem IP. The values for the Modem’s Local IP Address and Subnet Mask are shown here. In most cases,
keeping the default values will work.
•
•
Local IP Address. The default value is 192.168.1.1.
Subnet Mask. The default value is 255.255.255.0.
•
Network Address Server Settings (DHCP). Configure the Modem’s Dynamic Host Configuration Protocol (DHCP)
settings in this section.
Figure 4-9: Network Setup
•
Local DHCP Server. A Dynamic Host Configuration Protocol (DHCP) server automatically assigns an IP
address to each computer on your network for you. Unless you already have one, it is highly
recommended that you leave the Modem enabled as a DHCP server.
•
•
Start IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. This value
must be 192.168.1. 2 or greater, because the default IP address for the Modem is 192.168.1.1.
Number of Addresses. Enter the maximum number of users/clients that can obtain an IP address. The
number will vary depending on the starting IP address entered.
•
•
IP Address Range. The IP address range is displayed after entering the Start IP address.
Client Lease Time. The Client Lease Time is the amount of time a computer will be allowed connection to
the Modem with its current dynamic IP address. Enter the amount of time, in minutes, that the computer
will be “leased” this dynamic IP address.
Chapter 4: Configuring the ADSL Modem
The Setup Tab
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Time Setup
•
Set Time Zone. Select the appropriate time zone for the Modem’s location. If appropriate, check the
Automatically adjust clock for daylight saving changes checkbox.
•
Configure Time Server (NTP). When the Automatic Time Server Maintenance checkbox is selected, the
Current Date and Time are synchronized to the selected Primary Server or Secondary Server (if the Primary is
unavailable) over the Internet.
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
DDNS
The Modem offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and
domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or
other server behind the Modem. Before you can use this feature, you need to sign up for DDNS service at
DynDNS.org or TZO.com.
DDNS Service. If your DDNS service is provided by DynDNS.org, then select DynDNS.org or if your DDNS service
is provided by TZO.com, then select TZO.com in the drop-down menu. To disable DDNS Service, select Disabled.
Figure 4-10: DynDNS.org
DynDNS.org
•
•
•
User Name, Password, and Host Name. Enter the User Name, Password, and Host Name of the account you
set up with DynDNS.org.
Internet IP Address. The Modem’s current Internet IP Address is displayed here. Because it is dynamic, it will
change.
Status. The status of the DDNS service connection is displayed here.
TZO.com
•
•
•
E-mail Address, Password, and Domain Name. Enter the Mail Address, TZO Password Key, and Domain Name
of the service you set up with TZO.
Internet IP Address. The Modem’s current Internet IP Address is displayed here. Because it is dynamic, this
will change.
Figure 4-11: TZO.com
Status. The status of the DDNS service connection is displayed here.
Chapter 4: Configuring the ADSL Modem
The Setup Tab
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
Advanced Routing
The Advanced Routing screen allows you to configure the dynamic routing and static routing settings.
•
•
Operating Mode. If you want to use Static Routing, select Gateway from the drop-down menu. If you have
more than one router in your network and you need to use Dynamic Routing, select Router from the
drop-down menu.
Static Routing. If the Modem is connected to more than one network, it may be necessary to set up a static
route between them. A static route is a pre-determined pathway that network information must travel to
reach a specific host or network. To create a static route, change the following settings:
•
Select set number. Select the number of the static route from the drop-down menu. The Modem supports
up to 20 static route entries. If you need to delete a route, after selecting the entry, click the Delete This
Entry button.
•
•
Enter Route Name. Enter a reference name for the defined route.
Destination LAN IP. The Destination IP Address is the address of the remote network or host to which you
want to assign a static route. Enter the IP address of the host for which you wish to create a static route. If
you are building a route to an entire network, be sure that the network portion of the IP address is set to 0.
Figure
4-12:
Advanc
ed Rou
ting
•
•
•
Subnet Mask. The Subnet Mask (also known as the Network Mask) determines which portion of an IP
address is the network portion, and which portion is the host portion.
Default Gateway. This IP address should be the IP address of the gateway device that allows for contact
between the Gateway and the remote network or host.
Interface. Select your interface from the drop-down menu. Select LAN or WAN (Internet).
Figure
4-13:
Routing
Table
•
Show Routing Table. Click the Show Routing Table button to open a screen displaying how data is routed
through your LAN. For each route, the Destination LAN IP, Subnet Mask, Gateway, and Interface are displayed.
Click the Refresh button to update the information. Click the Close button to return to the previous screen.
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
Chapter 4: Configuring the ADSL Modem
The Setup Tab
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
The Security Tab
Firewall
When you click the Security tab, you will see the Firewall screen. You can add Firewall Protection and Filter
Multicast.
•
Firewall Protection. To add Firewall Protection, click Enabled. If you do not want Firewall Protection, click
Disabled. If you enable Firewall Protection and click Save Settings, you enable the Schedule Rule, Access
Control, MAC Filter, URL Blocking, and Intrusion Detection tabs.
•
Filter Multicast. Multicasting allows for multiple transmissions to specific recipients at the same time. If
multicasting is permitted, then the Modem will allow IP multicast packets to be forwarded to the appropriate
computers. Place a checkmark in the box to enable filter multicasting, if unchecked this feature is disabled.
Figure 4-14: Firewall
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
Access Control
Access Control allows users to define the traffic type permitted or not permitted to WAN port service. This page
allows you to define service limitations of client PCs, including IP addresses, service type, and scheduling rule
criteria.
To add a filtering rule, click Add Filtering Rule. The Normal Filtering Table displays these rules.
•
•
•
Client PC Name. Enter a name or description for the client PC in the Client PC Description field.
Client PC IP Address. Enter the IP address or IP range you wish to filter in the Client PC IP Address field.
Client PC Service. Many common services have been predefined and made available for blocking or filtering.
To block a service, click the checkbox next to the service you wish to block.
•
User Define. You can define a custom filter by entering a TCP Port Range or UDP Port Range. You can select
Always Blocking from the pull down menu, or the schedule rules you previously set up on the Schedule Rule
screen.
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
Figure 4-15: Access Control
Chapter 4: Configuring the ADSL Modem
The Security Tab
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Schedule Rule
To set time periods for filtering or access, click Add Schedule Rule. The Schedule Rule Table displays these
scheduling rules.
•
•
Name/Comment. Choose a name for the rule (example: NoSurfingAfter10PM) and enter it in the Name field.
Enter a definition or comment for the rule (example: Block kids from Web after 10) in the Comment field.
Activate Time Period. You can set starting and ending times for specific days of the week or for every day.
Select the desired day or Every Day, then enter the Start Time and End Time using the twenty four hour
format (example: 22 00 is 10PM) in the hours and minutes fields.
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
Figure 4-16: Edit Schedule Rule
MAC Filter
This screen allows you to filter by MAC address. To filter by MAC address, enable MAC Address Control, then enter
up to 32 MAC addresses or copy the MAC addresses from the DHCP Client List drop down menu.
Control
•
MAC Address Control. To filter by MAC address, click the Yes button, or to disable the feature, click the No
button. When MAC Address Control is enabled, only computers with a MAC address listed in the table are
granted access to the Internet.
Filter Table
•
MAC Filtering Table. When MAC Address Control is enabled, you can enter up to 32 MAC addresses to be
allowed to access the network.
•
DHCP Client List. You can copy the MAC address from the DHCP Client List drop down menu. Select the MAC
address from the DHCP Client List drop down menu, click the Copy to button, and select the number you want
to copy it to.
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
Figure 4-17: MAC Filtering
Chapter 4: Configuring the ADSL Modem
The Security Tab
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
URL Blocking
This screen allows the user to block access to certain web sites from a particular PC by entering either a full URL
address or just a keyword of the web site. If you want to remove all the URLs and Keywords from the list, click the
Clear All button.
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
Intrusion Detection
This screen allows common hacker attacks to be blocked. All of these types of intrusions are blocked by default.
If you want to allow the traffic for a service through, check the box for the desired service.
Figure 4-18: URL Blocking
Intrusion Detection Features include RIP defect and Discard Ping to WAN.
Stateful Packet Inspection features include SPI and Anti-DoS firewall protection, Packet Fragmentation, TCP
Connection, UDP Session, FTP Service, H.323 Service, and TFTP Service.
Alert
•
•
•
•
Your E-mail Address. Enter the e-mail address that will receive alert logs in the field.
SMTP Server Address. Enter the IP address of the SMTP server in the field.
SMTP User Name. Enter the user name used to login to the SMTP server.
SMTP Password. Enter the password used to login to the SMTP server.
VPN
Virtual Private Networking (VPN) is a security measure that creates a secure connection between two remote
locations. The VPN screen allows you to configure your VPN settings to make your network more secure. Use the
settings on this tab to allow VPN tunnels using IPSec, L2TP, or PPTP protocols to pass through the Modem’s
firewall.
Figure 4-19: Intrusion Detection
VPN Passthrough
Chapter 4: Configuring the ADSL Modem
The Security Tab
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
•
•
•
IPSec Passthrough. Internet Protocol Security (IPSec) is a suite of protocols used to implement secure
exchange of packets at the IP layer. To allow IPSec Passthrough, click the Enabled option. To disable IPSec
Passthrough, click the Disabled option.
L2TP Passthrough. Layering 2 Tunneling Protocol Passthrough is an extension of the Point-to-Point Tunneling
Protocol (PPTP) used to enable the operation of a VPN over the Internet.To allow L2TP Passthrough, click the
Enabled option. To disable L2TP Passthrough, click the Disabled option.
PPTP Passthrough. Point-to-Point Tunneling Protocol Passthrough is the method used to enable VPN sessions
to a Windows NT 4.0 or 2000 server. To allow PPTP Passthrough, click the Enabled option. To disable PPTP
Passthrough, click the Disabled option.
The Applications and Gaming Tab
Figure 4-20: VPN Passthrough
The Applications and Gaming Tab allows you to set up public services on your network, such as web servers, FTP
servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any
applications that use Internet access to perform functions such as videoconferencing or online gaming. Some
Internet applications may not require any forwarding.)
Port Range Forwarding
The Port Forwarding screen sets up public services on your network, such as web servers, FTP servers, e-mail
servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use
Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications
may not require any forwarding.)
When users send this type of request to your network via the Internet, the Modem will forward those requests to
the appropriate computer. Any computer whose port is being forwarded should have its DHCP client function
disabled and should have a static IP address assigned to it because its IP address may change when using the
DHCP function.
•
•
•
•
•
Application. Enter the name you wish to give each application.
Start and End. Enter the starting and ending numbers of the port you wish to forward.
Protocol. Select the type of protocol you wish to use for each application: TCP, UDP, or Both.
IP Address. Enter the IP Address of the appropriate computer.
Figure 4-21: Port Range Forwarding
Enable. This checkbox must be selected to forward the requests to the defined IP address.
Chapter 4: Configuring the ADSL Modem
The Applications and Gaming Tab
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
Port Triggering
Port Triggering is used for special applications that can request a port to be opened on demand. For this feature,
the Modem will watch outgoing data for specific port numbers. The Modem will remember the IP address of the
computer that sends a transmission requesting data, so that when the requested data returns through the
Modem, the data is pulled back to the proper computer by way of IP address and port mapping rules.
•
•
•
•
•
Trigger Port. Enter the Trigger Port number in the field.
Trigger Type. Select the Trigger Type protocol TCP or UDP
Public Port. Enter the name you wish to give each public port application.
Public Type. Select the Public Type protocol TCP or UDP.
Figure 4-22: Port Triggering
Enabled. Click the Enabled checkbox to enable port triggering for the chosen application.
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
NAT Mapping Table
Figure 4-23: NAT Mapping Table
NAT Mapping Table. Clicking this button will open a screen that allows you to view the current NAT address
mappings. Click Refresh to refresh the screen.
DMZ
The DMZ screen allows one local user to be exposed to the Internet for use of a special-purpose service such as
Internet gaming and videoconferencing through DMZ hosting. DMZ hosting forwards all the ports for one
computer at the same time, which differs from Port Range Forwarding, which can only forward a maximum of 10
ranges of ports.
•
DMZ. This feature allows one local user to be exposed to the Internet for use of a special-purpose service
such as Internet gaming and videoconferencing. To use this feature, select Enabled. To disable DMZ, select
Disabled.
•
Client PC IP Address. To expose one computer, enter the computer’s IP address.
Figure 4-24: DMZ
Chapter 4: Configuring the ADSL Modem
The Applications and Gaming Tab
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
The Administration Tab
Management
This section of the Administration tab allows the network’s administrator to manage specific Modem functions for
access and security.
Local Modem Access. You can change the Modem’s password from here. Enter a new Modem password and then
type it again in the Re-enter to confirm field to confirm.
Remote Administration. To access the Modem remotely, from outside the network, select Enabled. Then, enter
the port number that will be open to outside access in the Administration Port field. You will need to enter the
Modem’s password when accessing the Modem through Remote Administration.
IMPORTANT: Enabling Remote Administration allows anyone with access to your
password to configure the Modem from somewhere else on the Internet.
Figure 4-25: Management
UPnP. UPnP allows Windows to automatically configure the Modem for various Internet applications, such as
gaming and videoconferencing. When using UPnP features, select Enabled. Because allowing this may present a
risk to security, this feature is disabled by default.
When finished making your changes on this tab, click the Save Settings button to save these changes, or click
the Cancel Changes button to undo your changes.
SNMP
SNMP is a popular network monitoring and management protocol. To enable SNMP, click Enabled. To disable
SNMP, click Disabled.
SNMP Community
•
Community. The community name functions as a password for sending trap notifications to the target SNMP
program. It is useful to manage multiple devices at the same time. Enter the name of the community you’re
using.
Figure 4-26: SNMP
Chapter 4: Configuring the ADSL Modem
The Administration Tab
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
•
•
Access. Select the type of access allowed to the Modem’s SNMP information by the selected community: read
or write.
Valid. To enable the community’s access, click the Valid checkbox.
SNMP Trap
Trap to. Enter the IP address of the remote host computer that will receive the trap messages.
Community. The community name functions as a password for sending trap notifications to the target SNMP
program. It is useful to manage multiple devices at the same. Enter the name of the community you’re using.
Version. Select the version number
Log
The Modem can keep logs of all traffic for your Internet connection. To disable the Log function, keep the default
setting, Disabled. To monitor traffic between the network and the Internet, select Enabled. When you wish to
view the logs, click Incoming Log or Outgoing Log, depending on which you wish to view.
Change these settings as described here and click the Save Settings button to apply your changes or Cancel
Changes to cancel your changes.
Figure 4-27: Log
Figure 4-28: Incoming Log
Figure 4-29: Outgoing Log
Chapter 4: Configuring the ADSL Modem
The Administration Tab
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Diagnostics
The diagnostic tests (Ping and Traceroute) allow you to check the connections of your network components.
Ping Test. The Ping test will check the status of a connection. Click the Ping button to open the Ping Test screen.
Enter the address of the PC whose connection you wish to test and how many times you wish to test it. Then,
click the Ping button. The Ping Test screen will show if the test was successful. To stop the test, click the Stop
button. Click the Clear Log button to clear the screen. Click the Close button to return to the Diagnostics screen.
Traceroute Test. To test the performance of a connect, click the Traceroute button. Enter the address of the PC
whose connection you wish to test and click the Traceroute button. The Traceroute Test screen will show if the
test was successful. To stop the test, click the Stop button. Click the Clear Log button to clear the screen. Click
the Close button to return to the Diagnostics screen.
Figure 4-30: Diagnostic Tests
Change these settings as described here and click the Save Settings button to apply your changes or Cancel
Changes to cancel your changes.
Figure 4-31: Ping Test
Figure 4-32: Traceroute Test
Chapter 4: Configuring the ADSL Modem
The Administration Tab
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Firmware Upgrade
Firmware can be upgraded by clicking the Upgrade button after browsing for the firmware, which you can
download from the Linksys website. Do not upgrade your firmware unless you are experiencing problems with
the Modem. For more information about upgrading firmware, refer to “Appendix B: Upgrading Firmware”.
Figure 4-33: Firmware Upgrade
Factory Defaults
Restore Factory Defaults. If you wish to restore the Modem to its factory default settings and lose all your
settings, click Yes.
To begin the restoration process, click the Save Settings button to save these changes, or click the Cancel
Changes button to undo your changes.
Figure 4-34: Factory Defaults
Reboot
This tab allows you reboot of your Modem. To reboot your Modem, click the Device Reboot button.
Click the Cancel Changes button if you want to undo your changes.
Figure 4-35: Reboot
Chapter 4: Configuring the ADSL Modem
The Administration Tab
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
The Status Tab
Modem
This screen displays information about your Modem and its Internet connection.
Modem Information
Modem Information displays the Software Version, ADSL Version, Boot Code Version, and MAC Address.
DSL Status
The DSL Status will be displayed after connecting to the DSL. They are the DSL Status, DSL Modulation Mode,
DSL Path Mode, Downstream Rate, Upstream Rate, Downstream Margin, Upstream Margin, Downstream Line
Attenuation, Upstream Line Attenuation, Downstream Transit Power, Upstream Transit Power, and LOS Errors.
Figure 4-36: Status
Internet Connection
The Internet Connections will be displayed after selecting the Internet connection number from the drop-down
menu. They are PPP Login, Internet IP Address, Internet Netmask, and Internet Gateway.
Local Network
The Local Network information that is displayed is the local IP Address, Subnet Mask, and DHCP Server. To view
the DHCP Clients Table, click the DHCP Clients Table button.
DHCP Clients Table. Click the DHCP Clients Table button to show the current DHCP Client data. You will see the
MAC address, computer name, IP address, and expiration date of the network clients using the DHCP server. (This
data is stored in temporary memory and changes periodically.) To delete a client from the DHCP server, select the
client, then click the Delete button.
Figure 4-37: Local Network
Click the Refresh button if you want to Refresh your screen. Click the Close button to close the screen.
Figure 4-38: DHCP Clients Table
Chapter 4: Configuring the ADSL Modem
The Status Tab
24
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix A: Troubleshooting
This appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.”
Provided are possible solutions to problems that may occur during the installation and operation of the Modem.
Read the descriptions below to help you solve your problems. If you can’t find an answer here, check the Linksys
Common Problems and Solutions
1. I need to set a static IP address on a computer.
You can assign a static IP address to a computer by performing the following steps:
•
For Windows 98 and Me:
1. Click Start, Settings, and Control Panel. Double-click Network.
2. In The following network components are installed box, select the TCP/IP-> associated with your
Ethernet adapter. If you only have one Ethernet adapter installed, you will only see one TCP/IP line
with no association to an Ethernet adapter. Highlight it and click the Properties button.
3. In the TCP/IP properties window, select the IP address tab, and select Specify an IP address. Enter a
unique IP address that is not used by any other computer on the network connected to the Modem.
Make sure that each IP address is unique for each computer or network device.
4. Click the Modem tab, and in the New Modem prompt, enter 192.168.1.1, which is the default IP
address of the Modem. Click the Add button to accept the entry.
5. Click the DNS tab, and make sure the DNS Enabled option is selected. Enter the Host and Domain
names (e.g., John for Host and home for Domain). Enter the DNS entry provided by your ISP. If your ISP
has not provided the DNS IP address, contact your ISP to get that information or go to its website for
the information.
6. Click the OK button in the TCP/IP properties window, and click Close or the OK button for the Network
window.
7. Restart the computer when asked.
•
For Windows 2000:
1. Click Start, Settings, and Control Panel. Double-click Network and Dial-Up Connections.
2. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and
select the Properties option.
3. In the Components checked are used by this connection box, highlight Internet Protocol (TCP/IP), and
click the Properties button. Select Use the following IP address option.
4. Enter a unique IP address that is not used by any other computer on the network connected to the
Modem.
5. Enter the Subnet Mask, 255.255.255.0.
6. Enter the Default Gateway, 192.168.1.1 (Modem’s default IP address).
Appendix A: Troubleshooting
Common Problems and Solutions
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
7. Toward the bottom of the window, select Use the following DNS server addresses, and enter the
Preferred DNS server and Alternative DNS server (provided by your ISP). Contact your ISP or go on its
website to find the information.
8. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the
Local Area Connection Properties window.
9. Restart the computer if asked.
•
For Windows XP:
The following instructions assume you are running Windows XP with the default interface. If you are using
the Classic interface (where the icons and menus look like previous Windows versions), please follow the
instructions for Windows 2000.
1. Click Start and Control Panel.
2. Click the Network and Internet Connections icon and then the Network Connections icon.
3. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using,
and select the Properties option.
4. In the This connection uses the following items box, highlight Internet Protocol (TCP/IP). Click
the Properties button.
5. Enter a unique IP address that is not used by any other computer on the network connected to the
Modem.
6. Enter the Subnet Mask, 255.255.255.0.
7. Enter the Default Gateway, 192.168.1.1 (Modem’s default IP address).
8. Toward the bottom of the window, select Use the following DNS server addresses, and enter the
Preferred DNS server and Alternative DNS server (provided by your ISP). Contact your ISP or go on its
website to find the information.
9. Click the OK button in the Internet Protocol (TCP/IP) Properties window. Click the OK button in the
Local Area Connection Properties window.
2. I am not getting an IP address on the Internet with my Internet connection.
Verify the connection:
1. Make sure you are using the right Internet connection settings. Contact your ISP to see if your Internet
connection type is RFC 1483 Bridged, RFC 2516 PPPoE, or RFC 2364 PPPoA, or Bridged Mode Only.
Please refer to the Setup section of “Chapter 4: Configuring the ADSL Modem” for details on Internet
connection settings. Verify that the VPI and VCI settings are correct.
2. Make sure you have the right cable. Check to see if the Modem column has a solidly lit DSL LED.
3. Make sure the cable connecting from your Modem’s DSL port is connected to the wall jack of the DSL
service line.
4. Turn off the computer and Modem. Wait 30 seconds, and then turn on the Modem, and computer.
Check the Status tab of the Modem’s web-based utility to see if you get an IP address.
Appendix A: Troubleshooting
Common Problems and Solutions
26
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
3. I forgot my password, or the password prompt always appears when I am saving settings to the
Modem.
•
Reset the Modem to factory default by pressing the Reset button for 10 seconds and then releasing it. If
you are still getting prompted for a password when saving settings, then perform the following steps:
1. Access the Modem’s web-based utility by going to http://192.168.1.1 or the IP address of the Modem.
Enter the default username and password admin, and click the Administrations => Management
tab.
2. Enter a different password in the Modem Password field, and enter the same password in the second
field to confirm the password.
3. Click the Save Settings button.
4. To start over, I need to set the Modem to factory default.
Hold the Reset button for 10 seconds and then release it. This will return the Internet settings, password,
forwarding, and other settings on the Modem to the factory default settings. In other words, the Modem will
revert to its original factory configuration.
5. I need to upgrade the firmware.
In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download
•
Follow these steps:
download the latest firmware.
2. To upgrade the firmware, follow the steps in the Administration section found in “Chapter 4:
Configuring the ADSL Modem.”
6. My DSL service’s PPPoE is always disconnecting.
PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a
period of inactivity, just like a normal phone dial-up connection to the Internet.
•
There is a setup option to “keep alive” the connection. This may not always work, so you may need to re-
establish connection periodically.
1. To connect to the Modem, go to the web browser, and enter http://192.168.1.1 or the IP address of the
Modem.
2. Enter the username and password, if asked. (The default username and password is admin.)
3. On the Setup screen, select the option Keep Alive, and set the Redial Period option at 1 minute.
4. Click the Save Settings button. Click the Status tab, and click the Connect button.
5. You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you
see the login status display as Connected.
6. Click the Save Settings button to continue.
If the connection is lost again, follow steps 1- 6 to re-establish connection.
•
Appendix A: Troubleshooting
Common Problems and Solutions
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
7. The Power LED flashes continuously.
The Power LED lights up when the device is first powered up. In the meantime, the system will boot up itself
and check for proper operation. After finishing the checking procedure, the LED remains steady to show that
the system is working fine. If the LED continues to flash after this time, the device is not working properly. Try
to flash the firmware by assigning a static IP address to the computer, and then upgrade the firmware. Try
using the following settings, IP Address: 192.168.1.50 and Subnet Mask: 255.255.255.0.
8. When I enter a URL or IP address, I get a time-out error or am prompted to retry.
•
Check if other computers work. If they do, ensure that your computer’s IP settings are correct (IP Address,
Subnet Mask, Default Gateway, and DNS). Restart the computer that is having a problem.
If the computers are configured correctly, but still not working, check the Modem. Ensure that it is
connected and powered on. Connect to it and check its settings. (If you cannot connect to it, check the
LAN and power connections.)
•
•
•
Manually configure the TCP/IP settings with a DNS address provided by your ISP.
Make sure that your browser is set to connect directly and that any dial-up is disabled. For Internet
Explorer, click Tools, Internet Options, and then the Connection tab. Make sure that Internet Explorer is
set to Never dial a connection. For Netscape Navigator, click Edit, Preferences, Advanced, and Proxy.
Make sure that Netscape Navigator is set to Direct connection to the Internet.
Frequently Asked Questions
What is the maximum number of IP addresses that the Modem will support?
The Modem will support up to 253 IP addresses.
Is IPSec Passthrough supported by the Modem?
Yes, it is a built-in feature that is enabled by default.
Where is the Modem installed on the network?
The Modem is installed between the DSL wall jack and the LAN.
Does the Modem support IPX or AppleTalk?
No. TCP/IP is the only protocol standard for the Internet and has become the global standard for communications.
IPX, a NetWare communications protocol used only to route messages from one node to another, and AppleTalk, a
communications protocol used on Apple and Macintosh networks, can be used for LAN to LAN connections, but
those protocols cannot connect from the Internet to a LAN.
Does the LAN connection of the Modem support 100Mbps Ethernet?
The Modem supports 100Mbps over the auto-sensing Fast Ethernet 10/100 switch on the LAN side of the Modem.
Appendix A: Troubleshooting
Frequently Asked Questions
28
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Does the Modem support any operating system other than Windows 98SE, Windows Millennium,
Windows 2000, or Windows XP?
Yes, but Linksys does not, at this time, provide technical support for setup, configuration or troubleshooting of
any non-Windows operating systems.
The web page hangs; downloads are corrupt, or nothing but junk characters are being displayed on the
screen. What do I need to do?
Force your Ethernet adapter to 10Mbps or half duplex mode, and turn off the “Auto-negotiate” feature of your
Ethernet adapter as a temporary measure. (Please look at the Network Control Panel in your Ethernet adapter’s
Advanced Properties tab.) Make sure that your proxy setting is disabled in the browser. Check our website at
If all else fails in the installation, what can I do?
Reset the Modem by holding down the reset button until the Power LED fully turns on and off. Reset your DSL
modem by powering the unit off and then on. Obtain and flash the latest firmware release that is readily available
How will I be notified of new Modem firmware upgrades?
downloaded for free. To upgrade the Modem’s firmware, use the Administration tab of the Modem’s web-based
utility. If the Modem’s Internet connection is working well, there is no need to download a newer firmware
version, unless that version contains new features that you would like to use.
Will the Modem function in a Macintosh environment?
Yes, but the Modem’s setup pages are accessible only through Internet Explorer 4.0 or Netscape Navigator 4.0 or
higher for Macintosh.
I am not able to get the web configuration screen for the Modem. What can I do?
You can set your PC to a static IP Address.
Is the Modem cross-platform compatible?
Any platform that supports Ethernet and TCP/IP is compatible with the Modem.
How can I check whether I have static or DHCP IP Addresses?
Consult your ISP to obtain this information.
Can the Modem act as my DHCP server?
Yes. The Modem has DHCP server software built-in.
Appendix A: Troubleshooting
Frequently Asked Questions
29
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix B: Upgrading Firmware
The ADSL Modem allows you to upgrade firmware for the Modem through the Web-Utility's Firmware Upgrade tab
from the Administration tab. Follow these instructions:.
Firmware Upgrade
1. Click the Browse button to find the firmware upgrade file that you downloaded from the Linksys website and
then extracted.
2. Double-click the firmware file you downloaded and extracted. Click the Upgrade button, and follow the
instructions there.
Figure B-1: Upgrade Firmware
Appendix B: Upgrading Firmware
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix C: Glossary
This glossary contains some basic networking terms you may come across when using this product. For more
Access Point - A device that allows wireless-equipped computers and other devices to communicate with a
wired network. Also used to expand the range of a wireless network.
Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of
an access point.
AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption.
Bandwidth - The transmission capacity of a given device or network.
Bit - A binary digit.
Boot - To start a device and cause it to start executing instructions.
Broadband - An always-on, fast Internet connection.
Browser - An application program that provides a way to look at and interact with all the information on the
World Wide Web.
Byte - A unit of data that is usually eight bits long
ADSL Modem - A device that connects a computer to the cable television network, which in turn connects to the
Internet.
Daisy Chain - A method used to connect devices in a series, one after the other.
DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a
Default Gateway - A device that forwards Internet traffic from your local area network.
DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign
temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time,
instead of assigning permanent IP addresses.
Appendix C: Glossary
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be “seen” from
the Internet.
DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP
addresses.
Domain - A specific name for a network of computers.
Download - To receive a file transmitted over a network.
DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.
Dynamic IP Address - A temporary IP address assigned by a DHCP server.
EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access.
Many specific authentication methods work within this framework.
Encryption - Encoding data transmitted in a network.
Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common
transmission medium.
Firewall - A set of related programs located at a network gateway server that protects the resources of a
network from users from other networks.
Firmware - The programming code that runs a networking device.
FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network.
Full Duplex - The ability of a networking device to receive and transmit data simultaneously.
Gateway - A device that interconnects networks with different, incompatible communications protocols.
Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a
time.
HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World
Wide Web.
Infrastructure - A wireless network that is bridged to a wired network via an access point.
IP (Internet Protocol) - A protocol used to send data over a network.
Appendix C: Glossary
32
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
IP Address - The address used to identify a computer or device on a network.
IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device.
IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer.
ISP (Internet Service Provider) - A company that provides access to the Internet.
LAN - The computers and networking products that make up your local network.
MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking
device.
Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.
NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different
IP address for the Internet.
Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or
transmission between users.
Packet - A unit of data sent over a network.
Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically
generating the WEP encryption keys for Linksys products.
Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.
POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet.
Port - The connection point on a computer or networking device used for plugging in cables or adapters.
Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.
PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication
(username and password) in addition to data transport.
PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be
tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe.
RADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control
network access.
Appendix C: Glossary
33
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires.
Roaming - The ability to take a wireless device from one access point's range to another without losing the
connection.
Router - A networking device that connects multiple networks together.
Server - Any computer whose function in a network is to provide user access to files, printing, communications,
and other services.
SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet.
SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol.
SPI (Stateful Packet Inspection) Firewall - A technology that inspects incoming packets of information before
allowing them to enter the network.
SSID (Service Set IDentifier) - Your wireless network's name.
Static IP Address - A fixed address assigned to a computer or device that is connected to a network.
Static Routing - Forwarding data in a network via a fixed path.
Subnet Mask - An address code that determines the size of the network.
Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of
devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an
electrical circuit.
TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement
from the recipient of data sent.
TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a
network.
Telnet - A user command and TCP/IP protocol used for accessing remote PCs.
TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password
capability.
Throughput - The amount of data moved successfully from one node to another in a given time period.
Appendix C: Glossary
34
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for
each packet transmitted.
Topology - The physical layout of a network.
TX Rate - Transmission Rate.
Upgrade - To replace existing software or firmware with a newer version.
Upload - To transmit a file over a network.
URL (Uniform Resource Locator) - The address of a file located on the Internet.
VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another
over the Internet.
WAN (Wide Area Network)- The Internet.
WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for
greater security.
WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with
each other wirelessly.
WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol)
encryption, which can be used in conjunction with a RADIUS server.
Appendix C: Glossary
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix D: Specifications
Standards
IEEE 802.3, IEEE 802.3u, G.992.1 (G.dmt), G.992.2 (G.lite), G.922.3,
G.992.5, T1.413i2
Ports
Power, DSL, Ethernet
Reset
Buttons
Cabling Type
LEDs
UTP CAT 5 or better, Phone Cable (RJ-11)
Power, Ethernet, DSL, Internet
110 mm x 110 mm x 32 mm
0,135 kg
Dimensions
Unit Weight
Power
External, 9V DC, 1A
CE, UL, FCC
Certifications
Operating Temp.
Storage Temp.
Operating Humidity
Storage Humidity
0ºC to 40ºC
-20ºC to 70ºC
10% to 85% Non-Condensing
5% to 90% Non-Condensing
Appendix D: Specifications
36
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix E: Warranty Information
Linksys warrants to You that, for a period of two years (the “Warranty Period”), your Linksys Product will be substantially free
of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this
warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This
limited warranty extends only to the original purchaser.
If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return
Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are
requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a
copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You are
responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You only.
Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges.
ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED
TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You
specific legal rights, and You may also have other rights which vary by jurisdiction.
This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated,
repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical
or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for
intruding upon and attacking networks, Linksys does not warrant that the Product will be free of vulnerability to intrusion or
attack.
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT,
OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF
LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT
(INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT
WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if
any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.
This Warranty is valid and may be processed only in the country of purchase.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.
37
Appendix E: Warranty Information
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix F: Regulatory Information
FCC Statement
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which is found by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment or devices
Connect the equipment to an outlet other than the receiver's
Consult a dealer or an experienced radio/TV technician for assistance
Safety Notices
Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.
Do not use this product near water, for example, in a wet basement or near a swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
Industry Canada (Canada)
This device complies with Canadian ICES-003 rule.
Cet appareil est conforme à la norme NMB-003 d'Industry Canada.
EC Declaration of Conformity (Europe)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and Amendment Directive
93/68/EEC, this product meets the requirements of the following standards:
•
•
EN55022 Emission
EN55024 Immunity
Appendix F: Regulatory Information
38
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic
Equipment (WEEE)
This document contains important information for users with regards to the proper disposal and recycling of
Linksys products. Consumers are required to comply with this notice for all electronic products bearing the
following symbol:
Appendix F: Regulatory Information
39
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix F: Regulatory Information
40
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix F: Regulatory Information
41
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix F: Regulatory Information
42
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix F: Regulatory Information
43
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
Appendix G: Contact Information
Need to contact Linksys?
Visit us online for information on the latest products and updates to your existing products at:
If you experience problems with any Linksys product, you can e-mail us at:
In Europe
Austria
E-mail Address
[email protected] (English only)
Belgium
Czech Republic
Denmark
Finland
France
Germany
Greece
Hungary
Ireland
Italy
Netherlands
Norway
Poland
Portugal
Russia
Spain
Sweden
Appendix G: Contact Information
44
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL Modem
In Europe
Switzerland
E-mail Address
United Kingdom
Outside of Europe
Asia Pacific
E-mail Address
[email protected] (English only)
[email protected] (English only)
[email protected] (English only)
[email protected] (English only)
Latin America
Middle East & Africa
South Africa
UAE
U.S. and Canada
Note: For some countries, support may be available only in English.
Appendix G: Contact Information
45
Download from Www.Somanuals.com. All Manuals Search And Download.
|