Linksys SPA400
Trixbox Integration Guide
Access Point – Connecting You & Your Customers.
Contact : support@voipshop.com.au
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3 – Set the SPA400 to a Fixed IP address
Asterisk needs to access your SPA400, so it needs to be set to a
fixed ip address. To do this: -
Under Setup -> Basic Setup
• Select Fixed IP address and enter a valid fixed IP address for
your network.
• Be sure to enter a DNS server, if you do not know enter the
Telstra DNS server 139.130.4.5 – You can leave the secondary
blank
• Set your time zone.
• Click Save Settings
• Restart System
Sample Config – Use Address Valid For Your Network
Check with the network administrator if unsure.
Note the IP address in the Notes Section.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4 – Setup the SPA400 Voice Configuration.
Open the SPA400 in your web browser using the new IP address.
Select Setup->SPA9000 Interface.
• Enter SPA400 in the User ID:
• Leave SPA9000 on discover automatically
• No other changes should need to be made
• Click Save Settings (You Do Not Need To Restart)
Screenshot of Setup -> SPA9000 Interface
Select Setup -> Voice
Download from Www.Somanuals.com. All Manuals Search And Download.
For Australia you need to change:-
• Impedance : 220 Ohms + (820 Ohms || 120nF)
• On-Hook speed : 26ms
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5 – Configure Trixbox Trunk.
Open your FreePBX interface: http://trixbox.ip/admin/
Select Trunks -> Add SIP trunk
Complete the form with the details below:
----------------------------------------------------------------------
Outbound Caller ID: Blank
Never Override CallerID : Unticked
Maximum Channels: (the number of pstn lines plugged into the
SPA400)
Dial Rules: Leave Empty
Outbound Dial Prefix: Empty
Trunk Name: SPA400 (Can be anything you wish)
Peer Details:
allow=ulaw
canreinvite=no
context=from-trunk
dtmfmode=rfc2833
host=x.x.x.x
insecure=very
type=friend
user=SPA400
USER Context: Leave Blank
USER Details: Blank (Delete the default information)
Register String:
SPA400@x.x.x.x/SPA400
-----------------------------------------------------------------------
Note : x.x.x.x should be where you enter the IP address of the
SPA400
Click Submit Changes.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 6 – Configure Outbound Route.
You can now treat the SPA400 like any other trunk. To add an
outbound router (eg, dial 9 to dial out the SPA400)
Outbound Routes -> Add Route
Route Name: SPA400PSTN (this can be anything)
Route Password: Blank
Emergency Dialing: Unticked
Intra Company Route: Unticked
Dial Patterns: 9|.
Trunk Sequence: SPA400
Click Submit Changes
Step 7 – Configure Inbound Route.
This will setup an inbound route for people who call the PSTN lines
plugged into the SPA400.
Setup -> Inbound Routes -> Add Incoming Route
DID Number: SPA400 (case sensitive)
Caller ID Number: Blank
Zaptel Channel: Blank
Fax Handling
Leave as is
Select the Destination
Click Submit
Click the Red “Apply Configuration Changes” to reload asterisk
Download from Www.Somanuals.com. All Manuals Search And Download.
Complete:
You should now be able to make and receive calls via your SPA400.
Congratulations
Notes:
SPA400 IP Address: _____________________________
SPA400 Username: ______________________________
SPA400 Password: ______________________________
Number of Lines: _____
Installed By: _______________________________
Date: ______________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
|
KWC Outdoor Shower 26000540000 User Manual
Legacy Car Audio Car Video System LD63MU User Manual
Lennox Hearth Bluetooth Headset BT 320S User Manual
LG Electronics Air Conditioner LP6000ER User Manual
Linn Stereo Amplifier 500 Solo User Manual
Lowrance electronic GPS Receiver X96 User Manual
Magellan GPS Receiver 5390 User Manual
Magnavox CD Player MPC421 User Manual
McCulloch Trimmer MCT2027 User Manual
Metrologic Instruments Scanner MS2221 MS2222 User Manual