Linksys Network Card EG1032 User Manual

M a k i n g Co n n e c t i v i t y Ea s i e r  
Instant Gigabit Series  
Quick Installation  
This sheet will guide you through the basic steps needed to install the Instant  
Gigabit Network Adapter onto your network. If you have any problems during  
installation, refer to the Troubleshooting section of the User Guide.  
for Windows 95  
Instant Gigabit Network Adapter  
Model No.: EG1032  
EG1064  
6. Once Windows has located the drivers, the following window  
Overview  
will appear. To use this driver, click the Finish button.  
After installing the Instant Gigabit hardware in your PC, follow  
these instructions to install the adapter driver. The installation  
procedure for the adapter driver will vary slightly, depending on  
the version of Windows 95 you are using. If you experience any  
difficulty, refer to your User Guide for more information.  
Note: Do not click Cancel or Skip at any time during the installation.  
Doing so will prevent the driver from being properly installed on your  
PC.  
Installing Your Instant Gigabit Network  
Adapter Drivers  
At this point, the installation may require files from your  
Windows 95 CD-ROM. If prompted, insert your Windows 95  
CD-ROM into your CD-ROM drive and enter d:\win95 in the  
box that appears (where “d” is the letter of your CD-ROM  
drive). If you were not supplied with a Windows 98 CD-  
ROM, your Windows files may have been placed on your  
hard drive by your computer manufacturer. While the loca-  
tion of these files may vary , many manufacturers use c:\win-  
dows\options\cabs as the path. Try entering this path into the  
box. If no files are found, check your computers documenta-  
tion or contact your computer manufacturer for more infor-  
mation.  
1. Start up your PC.  
2. Windows 95 will automatically detect the Network Adapter  
in your computer. If the Update Device Driver Wizard win-  
dow appears, you are using Windows 95 version B. If a win-  
dow other than this appears, you are using Windows 95 ver-  
sion A. For Windows 95 version A driver installation, refer  
to the Appendix of the User Guide.  
7. Once the driver is installed, the Advanced Settings screen  
will appear. The default settings should allow the Adapter to  
function properly. Click the OK button to continue. For more  
information about these settings, refer to the Advanced  
Settings section of the User Guide.  
8. When asked if you want to restart your PC, remove all disks  
from your computers drives and click the Yes button. If  
Windows does not ask you to restart your PC, click the Start  
button, choose Shut Down, choose Restart, then click Yes.  
3. While the Update Device Driver Wizard window is visible,  
insert the Instant Gigabit Network Adapter Driver Disk  
into your floppy drive and click the Next button.  
4. Windows 95 will find the Linksys EG1032/EG1064 Instant  
Gigabit Network Adapter driver on the disk. Click the Finish  
button to continue. If Windows fails to find the driver, click  
the Other Locations button to browse for the driver.  
The Windows 95 Version B driver installation is complete.  
Refer to the section in your User Guide on Configuring the  
Instant Gigabit Network Adapter for Windows 95, 98, and  
Millennium for more information about the setup of the  
Adapter.  
5. If you clicked the Other Locations button, enter a:\win95 in  
the Window that appears. Windows will begin copying the  
Network Adapters driver files to your PC.  
QI-EG1032/EG1064-10226NC WIN95 DG  
Download from Www.Somanuals.com. All Manuals Search And Download.  

La Crosse Technology Stud Sensor TX7U User Manual
Lennox International Inc Heat Pump 61H42 User Manual
Lenoxx Electronics Air Conditioner XC15 User Manual
Lenoxx Electronics CD Player CD 107 User Manual
LevelOne Switch FSW 1610TX User Manual
Linear Radio MDR User Manual
Lochinvar Water Heater JR SUB 07 User Manual
McCulloch Chainsaw MAC 3 14XT User Manual
MicroBoards Technology DVD Recorder BluRay Series User Manual
Micron Technology Pacemaker TX716A User Manual