Five special utility functions can be displayed by pressing the pound (#) key then the
digits 1-5. They display the status of the obstacle transmitter, the number of empty
programming locations, the total number of transmitters programmed, first available
programming location and firmware version number.
INTRODUCTION
®
The AP-1 is designed for a broad range of access control applications. Its wireless
design, smallsizeanddualrelayoutputsmakeiteasilyadaptableforavarietyofaccess
control requirements. Typically, the AP-1 is used to control a door strike, barrier gate,
automatic gate or automatic door operator.
The AP-1 can fully supervise the MGT safety edge transmitter. The system monitors
the MGT transmitter for hourly status reports, tamper signals and low battery signals.
A beep will sound every 5 seconds if a fault occurs and the trouble source can be
displayed by pressing pound (#)-1. For a trouble indication, a transmitter must be
activated twice to trigger the ACCESS RELAY if a supervisory condition exists on the
MGT transmitter.
AP-1
The AP-1 contains a high-gain UHF receiver which uses an external antenna to pick
up signals from up to 250 feet away. Up to 169 Linear MegaCode Format transmitters
and one Model MGT safety edge transmitter can easily be programmed into the AP-1’s
memory. The AP-1 will retain its memory, even without power.
POWER
EARTH
12-24
G
N
D
PO ER
W
V
A
C
/
V
D
C
INPU
T
TRANSMITTER
NUMBER
OPEN RE
QU
E
ST
N.C.
A
RE
CCESS
COM
L
A
Y
ACCESS GRANTED
SUSPENDED
OCCUPIED
N.O.
Wireless Access
Control Receiver
Insta lla tio n Instruc tio ns
N.C.
OB
RE
STA
C
L
E
COM
N.O.
L
A
Y
RADIO
Two dry contact relay outputs are standard. One relay is the ACCESS RELAY, which
triggers for two seconds each time a programmed transmitter is activated. This relay
output connectsto thepushbutton orradio inputof theaccessdevice. Thesecondrelay
is the OBSTACLE RELAY, which triggers for two seconds when an obstacle signal is
sent from a Model MGT safety edge transmitter. This relay output connects to the
obstacle input of the access device. An OPEN REQUEST input terminal is supplied for
hardwire activation of the access device with an external pushbutton.
MOUNTING
SCREWS
F-81 CONNECTOR
NUT AND
LOCKWASHER
POWER
E
A
RTH G
12-24
C/
PEN REQ
N
D
PO R
INPU
W
E
T
VA
VD
C
TRANSMITTER
NUMBER
O
U
EST
N.C.
COM
N.O.
A
RE
C
C
E
SS
L
A
Y
ACCESS GRANTED
SUSPENDED
OCCUPIED
WHIP
ANTENNA
N.C.
COM
N.O.
OB
RE
STA
C
L
E
L
A
Y
The AP-1 can be powered from 12-24 Volts AC or DC. The Form C relay outputs can
switch up to 1 Amp each. An EARTH GROUND terminal is provided as an optional
connection for maximum lightning and static protection.
RADIO
(619) 438-7000 • FAX (619) 438-7043
USA & Ca na d a (800) 421-1587 & (800) 392-0123
To ll Fre e FAX (800) 468-1340
3-FOOT
ANTENNA
CABLE
TRANSFORMER
ACCESSPRO MODEL AP-1 RECEIVER
AP-1 FEATURES
NUMERIC KEYPAD
SUSPEND BUTTON
LEARN BUTTON
For entering memory
location numbers and
utility function numbers.
Push after entering
DIGITAL DISPLAY
Prevents selected transmitter from
activating the access relay but
does not remove it from memory.
POWER INDICATOR
transmitter number to start
learn cycle. To complete the
cycle, activate a transmitter
while occupied light is
blinking.
Displays transmitter numbers
during operation and
TERMINAL STRIP
Lights when AC or DC
power is applied to the
unit.
For connection of earth ground,
power and open request inputs
plus access and obstacle relay
outputs.
ANTENNA CONNECTOR
programming. Also displays
MGT supervision status and
system utility information.
For direct connection to
the local whip antenna
or, with coax cable, to
the remote antenna.
ACCESS GRANTED INDICATOR
Lights when the access
or obstacle relay is
energized.
DELETE BUTTON
Push once after entering the
transmitter number to delete.
Press again while the occupied
light is blinking to delete
selected transmitter from
memory.
SUSPENDED INDICATOR
Lights when a signal is
received from a
transmitter that has
been suspended from
use.
OCCUPIED INDICATOR
Lights when the
POUND (# ) KEY
displayed memory
location is occupied.
Blinks during transmitter
learn cycle and before
transmitter is deleted.
Adds 1 to the displayed number. Also
press # then 1-5 for utility functions:
#-1 Displays MGT supervisory status.
#-2 Displays number of empty memory locations.
#-3 Displays number of occupied memory locations.
#-4 Displays first available memory location.
#-5 Displays firmware version number.
RADIO INDICATOR
OPEN BUTTON
STAR (*) KEY
Lights when a radio
Push to activate the access
relay. Also clears any
Displays the number of the last
signal is detected on the
frequency to which the
receiver is tuned.
transmitter activated or
subtracts 1 from the displayed
number.
supervisory trouble codes from
MGT transmitter.
RECEIVER INSTALLATION
ANTENNA INSTALLATION
ELECTRICAL CONNECTIONS
EARTH GROUND
LOCAL ANTENNA
Attach local whip
antenna directly to
receiver. Bend whip to
point antenna up.
REMOTE ANTENNA
EXA-1000 REMOTE ANTENNA
Ground stake, cold
water pipe or unified
earth ground.
Use the optional
Mount F-81 connector
on surface using
EXA-1000 antenna
mounted as high as
possible for best radio
range. Connect to
receiver with RG-59
coax cable.
MOUNT RECEIVER
USING THE FOUR
SCREWS PROVIDED
lockwasher and nut.
Connect to receiver
with coax cable and
screw whip antenna to
connector.
12-24
VOLTS
AC/DC
POWER INPUT
Low voltage plug-in
transformer or power
from access device.
1. Mount receiver in an area
protected from the elements.
ATTACH
WHIP
ANTENNA
F-81
CONNECTOR
EARTH GND
12-24 POWER
C/ VDC INPUT
VA
TRANSMITTER
NUMBER
2. If using the local whip
antenna, the higher the
receiver is mounted, the
better the radio range will be.
OPEN REQUEST
N.C.
COM
N.O.
OPEN REQUEST PUSHBUTTON
Optional connection
provides an external
method to activate
access device.
A
RELA
CCESS
Y
ACCESS GRANTED
SUSPENDED
OCCUPIED
N.C.
COM
N.O.
OBSTACLE
RELA
Y
RADIO
3. Optionally, mount the
receiver in a metal cabinet
and use an external antenna.
Pushbutton or Radio
Terminals
ACCESS DEVICE
ACCESS AND OBSTACLE RELAY TERMINALS
Connect to access device. Select
normally open or normally closed
terminals to match access device.
COAX TO
RECEIVER
Obstacle
Terminals
EXA-1000 ANTENNA
Download from Www.Somanuals.com. All Manuals Search And Download.
|