WT00Z-1
Radio Frequency (RF) Controlled, 120 VAC, Wall Mounted
Transmitter, Series 300
WHITE
BLACK
NEUTRAL
120 VAC
LINE
TO MOUNT MORE THAN ONE
PUSH ON (PUSH
& HOLD TO BRIGHTEN)
WT00Z-1IN A BOX, SCORED TAB
WILL BREAK FLUSH WITH EDGE
OF PLASTIC
PUSH OFF
(PUSH AND
HOLD TO DIM)
PUSH TOP OR
GROUND
GREEN
BOTTOM OF PADDLE
SWITCH ONCE TO
INCLUDE IN NETWORK
STATUS LED
SUPPLIED WITH DECORATIVE SWITCH PLATE
NOTE: This module must be “included in the Network” only where it will be permanently installed. The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes.You cannot “test bench” configure this module.
WTOOZ-1 WALL MOUNTED TRANSMITTER
INCLUDING WT00Z-1 TO THE NETWORK
Linear’s family of Z-Wave certified wireless lighting controls (switches,
dimmers, outlets and plug-in modules) brings a new level of intelligent
wireless capability to commercial and residential environments.
STEP 1. Prepare the Controller to include a unit to the network by
adding it to a group (method of adding a node to the network). Refer
to controller instructions.
The Z-Wave wireless protocol is an international wireless standard
for remote home automation, security and other applications.
Embedded in each device, the Z-Wave smart chip enables two-way RF
communication among hundreds of Z-Wave enabled devices, allowing
products and services from multiple manufacturers to work seamlessly.
STEP 2. The WT00Z-1 must be in its permanently installed
location. Tap either the top or bottom of the WT00Z-1 once.
STEP 3. You should see an indication on your Controller that the
“device was included” in the network.
NOTE: If you have trouble adding the WT00Z-1 to a group it may be
that the Home ID and Node ID were not cleared from it after testing.
You must first “RESET UNIT” with your controller to remove it from
the network. Although adding it to a group includes it in the network,
removing it from a group does not remove it from the network. If
removed from a group, it functions as a repeater (only). “RESET UNIT”
removes it completely from the network.
Linear Z-Wave products are easy to install, and allow dealers to create
an integrated wireless network with nearly limitless expansion and
interoperability with security and health monitoring systems, energy
management, home entertainment, appliances, and more.
INSTALLATION
DANGER! SHOCK HAZARD. Read and understand these
instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the
United States, or the Canadian Electrical Code and local regulations
in Canada. It is recommended that a qualified electrician perform this
installation. Retain instructions for future use. With power off, wire this
WT00Z-1 according to the diagram shown above. If more than one
WT00Z-1 is to be installed in a wall box, scored tabs on the side can
be broken off by bending back and forth with pliers, to accommodate
proper fit. Apply power when completed. Refer to your Controller
operating instructions on how to include this module in the RF network
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Dim Rate
For example:There are 3 sets of parameters that can adjust the dimming
rate of the WT00Z-1.
Enable Shade Control Group 1
The WT00Z-1 can control shade control devices via its group 1 if this
configuration parameter is set to 1.
• Parameter 16
• Length: 1 Byte
• Valid Values = 0 or 1 (default 0)
1. One set to control how fast the dim rate is when the dimmer receives
a Z-Wave command excluding ALL ON or ALL OFF command.
2. One set to control how fast the dim rate is when the dimmer is
locally controlled.
Enable Shade Control Group 2
The WT00Z-1 can control shade control devices via its group 2 if this
configuration parameter is set to 1.
• Parameter 14
• Length: 1 Byte
• Valid Values: 0 or 1 (default 0)
3. One set to control how fast the dim rate is when the dimmer receives
an ALL ON or ALL OFF command.
These values can be changed instantly to allow various scenes and
effects. The first of these parameters is the “dim step” (dim rate)
parameter. It can be set to a value of 1 to 99. This value indicates how
many levels the dimmer will change when the timer (discussed below)
expires. The second parameter is the timing (how fast the dim rate)
parameter. It can be set to a value of 1 to 255.This value indicates in 10
millisecond resolution, how often the dim level will change. For example,
if you set this parameter to 1, then every 10mS the dim level will change.
If you set it to 255, then every 2.55 seconds the dim level will change.
With the combination of the two parameters that can control the dim
rate, the dimmer can be adjusted to dim from maximum to minimum or
minimum to maximum at various speeds between 10 millisecond and
252.45 seconds (over 4.25 minutes).
Enable Shade Control Group 3
The WT00Z-1 can control shade control devices via its group 3 if this
configuration parameter is set to 1.
• Parameter 15
• Length: 1 Byte
• Valid Values: 0 or 1 (default 0)
LEDTransmission Indication
The WT00Z-1 will flicker its LED when it is transmitting to any of its 4
groups. This flickering can be set to not flicker at all (set to 0), to flicker
the entire time it is transmitting (set to 1), or to flicker for only 1 second
when it begins transmitting (set to 2). By default, the WT00Z-1 is set to
flicker for only 1 second.
• Parameter 19
• Length: 1 Byte
• Valid Values = 0 , 1, 2 (default 2)
• Parameter 7-12
• Length: 1 Byte
• Valid Values: (See next)
NOTE: that this only affects a level that is reported or possibly sent by Poll: Minutes
the WT00Z-1 since the WT00Z-1 does not control a load.
The WT00Z-1 will poll the first node in Group 1 in order to keep itself
synchronized with the group if this configuration parameter is set to 1.
How often it will poll is configured using this parameter.
• Parameter 20
• Length: 1 Byte
• Valid Values = 1 through 255 (default: 2)
On/Off Command dim rate (excluding ALL ON/ALL OFF commands)
• Parameter 7
• Dim step Parameter (default = 3)
• Valid Values: 1-99
• Parameter 8
Poll First Node in Group 1
• Dim timer Parameter (default =10)
• Valid Values: 1-255
The WT00Z-1 will poll the first node in Group 1 in order to keep itself
synchronized with the group if this configuration parameter is set to 1.
• Parameter 21
Local Control dim rate
• Parameter 9
• Length: 1 Byte
• Valid Values = 0 , 1 (default 0)
• Dim step Parameter (default = 3)
• Valid Values: 1-99
• Parameter 10
• Dim timer Parameter (default = 10)
• Valid Values: 1-255
Each Configuration Parameter can be set to its default setting by setting
the default bit in the Configuration Set command. See your controller’s
instructions on how to do this (and if it supports it). All Configuration
commands will be reset to their default state when the WT00Z-1 is
“reset” thus removing it from the Z-Wave network.
ALL ON/ALL OFF dim rate
• Parameter 11
• Dim step Parameter (default = 3)
• Valid Values: 1-99
• Parameter 12
SPECIFICATIONS
Power:
Signal:
Range:
120 VAC, 60 Hz
• Dim timer Parameter (default = 10)
• Valid Values: 1-255
(Frequency) 908.42 MHz
Up to 100 feet line of sight between the Controller
and /or the closest EGC Receiver Module
Disable Group 4 During a Dim Command
After the WT00Z-1 is commanded to stop dimming when dimming
because of the DIM START command, it will then command the Z-Wave
devices that are in Group 4 to its new level. To prevent the WT00Z-1
from commanding the Z-Wave devices in Group 4 during this particular
occurrence, set Parameter 13 to the value of 1.
• Parameter 13
INTEROPERABILITY WITH Z-WAVE DEVICES
A Z-Wave™ network can integrate devices of various classes, and these
devices can be made by different manufacturers. The WT00Z-1 can be
incorporated into existing Z-Wave™ networks. The top or bottom of the
WT00Z-1 switch paddle can be used to carry out inclusion (adding to
the network by adding to a group), association (operate simultaneously
with other nodes), exclusion (remove from a group) or reset (remove
from the network). Controllers can be replicated in order to provide
operation from other locations.
• Length: 1 Byte
• Valid Values = 0 or 1 (default 0)
NOTE: This only affects a level that is reported or possibly sent by the
WT00Z-1 since the WT00Z-1 does not control a load.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
REGULATORY INFORMATION
WARRANTY
The WT00Z-1 is certified to comply with applicable FCC and IC rules
and regulations governing RF and EMI emissions.This device complies
with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including
interference that may cause undesired operation.
This Linear product is warranted against defects in material and
workmanship for twelve (12) months. This warranty extends only to
wholesale customers who buy direct from Linear or through Linear’s
normal distribution channels. Linear does not warrant this product to
consumers. Consumers should inquire from their selling dealer as to
the nature of the dealer’s warranty, if any. There are no obligations
or liabilities on the part of Linear Corporation for consequential
damages arising out of or in connection with use or performance
of this product or other indirect damages with respect to loss
of property, revenue, or profit, or cost of removal, installation, or
reinstallation. All implied warranties, including implied warranties for
merchantability and implied warranties for fitness, are valid only until
Warranty Expiration Date as labeled on the product. This Linear LLC
Warranty is in lieu of all other warranties express or implied.
FCC NOTICE
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Services at
1-800-421-1587 for an RPA# and other important details.
IMPORTANT !
Linear radio controls provide a reliable communications link and fill an
important need in portable wireless signaling. However, there are some
limitations which must be observed.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected
• For U.S. installations only: The radios are required to comply with
FCC Rules and Regulations as Part 15 devices. As such, they have
limited transmitter power and therefore limited range.
• Consult the dealer or an experienced radio/TV technician to help.
• Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment
• A receiver cannot respond to more than one transmitted signal at a
time and may be blocked by radio signals that occur on or near their
operating frequencies, regardless of code settings.
IC NOTICE
This Class B digital apparatus complies with Canadian ICES-003
• Changes or modifications to the device may void FCC compliance.
• Infrequently used radio links should be tested regularly to protect
against undetected interference or fault.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada. Le présent appareil est conforme aux CNR
d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil
ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
• A general knowledge of radio and its vagaries should be gained prior
to acting as a wholesale distributor or dealer, and these facts should
be communicated to the ultimate users.
Cet appareil numérique de la classe B est conforme à la norme NMB-
003 du Canada. Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device.
Copyright © 2013 Linear LLC 234730 AX2
P1774 X3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|