Life Fitness Home Gym SM82 User Manual

8 STACK MULTI-JUNGLE (SM82)  
WITH ONE ADJUSTABLE PULLEY  
UNPACKING AND ASSEMBLY INSTRUCTIONS  
M051-K50-B118  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
UNPACKING  
Follow the steps below when unpacking the components of the SM82.  
1. Cut off the shipping wrapper.  
2. Remove the parts boxes and shipping boards.  
3. Remove the items in the parts boxes. These items are shown in Figure 1.  
A. Remove the bolts bag.  
B. Remove the parts shown below. Parts that are used to build the SM82 are  
described in the section HARDWARE at the end of these instructions.  
Figure 1. Parts box contents (box 1 on left, box 2 on right).  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
ASSEMBLY  
Figure 2 shows an assembled SM82.  
Figure 2. SM82 main components (seats and cables removed for clarity).  
1. Cubes (2)  
5. Lat tops (2)  
2. Low row bench (2)  
3. Lat bench (2)  
4. Connecting beam (1)  
6. Tricep top (1)  
7. Adj. X-over top (1)  
8. 300 lb. Weight stacks (4)  
9. 190 lb. Weight stacks (4)  
1.  
Place the two weight “cubes” in their “final resting spots.” The cubes will be  
approximately 11’4” apart as shown in Figure 3.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
Figure 3. Set the weight stack cubes.  
Figure 4. Configuration for 2-3/4” and 3” bolts.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
Figure 5. Configuration for 6” bolts.  
2.  
Bolt on the teardrop pulleys above the benches (see Figure 6) on both cubes using  
two 3/8” x 2-3/4” hex head bolts. Include the 3/8” flat washer, end cap washers, end caps  
and 3/8” Nyloc (locknut). Use the bolt configuration shown. You may wish to use a pinch  
bar to align the bolt holes.  
Figure 6. Bolt on the teardrop pulleys.  
3.  
Bolt connecting beam to cubes (part 4 from Figure 2) using a 5/8” socket with  
extension and combination wrench. Use two of the large 7/16” x 6” bolts, 7/16” washers,  
and 7/16” end cap washers and end caps. Figure 7 shows the connected cubes.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
3/8” x 3” (4)  
bolt top  
beams together  
7/16” x 6” (8)  
mount on tops  
U
T
V
T
Remove pulleys from  
housings to give clearance  
to socket extension  
Figure 7. Bolt on the connecting beam, lat tops, tricep tops.  
4.  
Mount the 56” lat tops (part T) to the cubes using a 5/8” socket and combination wrench  
by inserting two of the large 7/16” by 6” bolts using the hardware configuration shown in  
Figure 7. Mount the 29” tricep tops (part U) to the cubes using the 7/16” x 6” bolts.  
Secure to the lat tops using the 3/8” x 3” bolts. Use the hardware configuration shown in  
Figure 7. You will need to remove the pulleys from the teardrop pulley assemblies to gain  
clearance for the socket wrench extension. Leave the pulleys out of the housings until the  
cables have been installed.  
Figure 8. Mount rubber bumpers and the weight stacks.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
5.  
Install the weight stacks. To do this:  
A. Use a 9/16” socket and combination wrench and remove the tricep back rest  
bolts (see Figure 9).  
B. Use a 9/16” socket and combination wrench and unbolt the top plate and remove  
the guide rods (see Figure 9).  
Figure 9. Remove the tricep back rest, the top plate and the guide rods.  
C. Prepare the weight stack. Slide the guide rods (2) through the weight stacks (1)  
as shown below. Place rubber bumpers (3) on the bottoms of each guide rod.  
Make sure the pull pin (4) is in the bottom weight plate.  
D. Flip over the weight stacks. When shipped, the weight stacks have the pull pins  
facing upward. You will need to flip the stacks over so that the pull pins are facing  
outward when they are loaded onto the machine. Since the pull pins will be facing  
downward when they are flipped over, it is recommended that you put the stacks  
on a padded carpet to keep the pins from being damaged.  
E. Set the weight stacks onto the machine. Using a piano dolly, lift the weight  
stacks over the bottom plate and set the stacks onto the rubber bumpers with the  
plate numbers facing outward. The 300 lb weight stacks need to be facing the  
“sides” of the cells (where the benches will be attached- number 8 in Figure 9).  
The 190 lb weight stacks will need to be facing the “outsides” and “insides” of the  
cells (where the tricep pulleys and crossover pulleys will be attached- number 9 in  
Figure 8). Make sure the pull pins are facing outward.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
C. Prepare the weight stack-  
add bumpers to bottom, insert  
guide rods, put pull pin in  
bottom stack.  
D. Flip over the weight stack  
onto piano dolly.  
E. Hoist the weight  
stack onto the machine.  
Figure 10. Install the weight stacks.  
F. Bolt on the top plate to the top of the cells with the top plate on the guide rods  
as shown in Figure 11 using a 9/16” socket and combination wrench and the 3”  
bolts (with cap washers) that were previously inserted.  
Figure 11. Bolt on the top plate.  
6.  
Bolt the floating pulleys into the 190 lb weight stacks used for the crossovers using a  
7/8” combination wrench. You will need to remove the pulley from the housing to thread  
the plug into the weight stack bayonet. Make sure the 9/16” jam nut is threaded 1-5/8”  
away from the pulley as shown in Figure 12. Leave the pulleys out since you will need to  
have them out when the cable is routed.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
Figure 12. Bolt the floating pulleys into the crossover 190 lb weight stacks.  
7.  
Mount the seated row and lat benches to the frame. Use the 3/8” x 2-3/4” hex bolts on  
the upper bench frame holes as shown below. Use the 3/8” x 3” hex bolts on the lower lat  
bench holes as shown below. Use a 9/16” socket and combination wrenches.  
Use a pinch bar to align the  
seat frame holes to the cubes  
3/8” x 2-3/4” (8)  
3/8” x 3” (2)  
Figure 13. Mount the benches to the frame.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
Figure 14. Bolt the benches to the frame.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
INSTALLING THE CABLES  
The SM82 uses eight cables. There are three different types of cable used on the SM82. They  
are:  
1. Crossover cables (ball end cables) (3).  
2. Low row cable (the long cables) (2).  
3. Lat pulldown and tricep cables (3).  
The lat and tricep cables can be identified by their short length, the low row cables can be  
identified by their long length and the adjustable crossover cables can be identified by the ball  
on the end of the cable. The routings for these cables are shown in the figures below.  
NOTE: YOU MUST REMOVE ALL PULLEYS TO ROUTE THE CABLES.  
USE A 9/16” COMBINATION WRENCH AND SOCKET TO DO THIS  
(SEE FIGURE 15). YOU MAY WISH TO REMOVE THE SHOULDER  
BOLTS (FIGURE 15 RIGHT SIDE) BY USING A 3/8” COMBINATION  
WRENCH AND A 1/8” HEX KEY WRENCH. WHEN YOU HAVE  
ROUTED THE CABLES, REPLACE ALL PULLEYS AND PLACE  
END CAPS ON NUT AND BOLT ENDS. YOU MAY NEED TO PRY  
THE PULLEY HOUSINGS OPEN TO REPLACE THE PULLEYS.  
Figure 15. Removing the pulley bolts.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
ADJUSTABLE CROSSOVER CABLE ROUTING  
Once you’ve removed the pulleys as described previously, route the adjustable crossover  
cable as shown in Figure 16.  
Figure 16. Adjustable crossover cable routing.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
Figure 17. Adjustable crossover cable end detail.  
Using a 7/8” wrench, tighten the jam nut onto the adjustable pulley threads as shown in Figure  
17. Place a rubber cap on the top of the cable as shown in Figure 17 (right).  
CROSSOVER CABLE ROUTING  
Once you’ve removed the pulleys as described previously, route the two crossover cables as  
shown in Figure 18.  
Figure 18. Crossover cable routing.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
LOW ROW CABLE ROUTING  
Route the low row cables as shown in Figure 19.  
Figure 19. Low row cable routing.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
Bolt the cable to the weight stacks as shown in Figure 20. Thread the 7/8” nut up on the  
cable bolt as shown at left. Screw the bolt down into the weight stack as shown at right.  
Tighten the bolt with a 7/8” combination wrench.  
Figure 20. Screw the cable into the weight stack.  
LAT PULLDOWN CABLE ROUTING  
Route the lat pulldown cable as shown in Figure 21. Screw the cable into the weight stack as  
shown previously in Figure 20.  
Figure 21. Lat pulldown cable routing.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
TRICEP PUSHDOWN CABLE ROUTING  
Route the tricep pushdown cable as shown in Figure 22. Screw the cable into the weight stack  
as shown previously in Figure 20.  
Figure 22. Tricep pushdown cable routing.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
HARDWARE  
½
½
½
½
½
½
0
1
2
3
4
5
6
Hardware Figure 1. Assembly Parts.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
The parts shown in Hardware Figure 1 are used to assemble the SM82. They are:  
A. 7/16” x 6” hex head bolt (used to bolt the tricep top beams, lat top beams, and  
connecting beam to the tops of the cubes)  
B. 7/16” flat washer  
C. 7/16” cap washer (used on the head end of the 6” bolt so end cap will fit on the nut)  
D. 7/16” hex head nut  
E. 3/8” x 3” hex head bolt (used to bolt the tricep pushdown beams to the connecting  
beam)  
F. 3/8” x 2-3/4” hex head bolt (used for all other connections)  
G. End caps (bolt covers)  
H. 3/8” flat washer  
J. 3/8” end cap washers (end caps snap onto them)  
K. 3/8” Nyloc (locknut)  
The part shown in Hardware Figure 2 is the 9/16” cable jam nut that’s used to secure the  
cables to the weight stacks.  
Hardware Figure 2. Cable jam nut.  
M. Cable jam nut  
Hardware Figure 3 shows the types of cables that are included with the SM82.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
Hardware Figure 3. Cables.  
N. Lat pulldown cables (same as tricep cable) (2)  
P. Tricep cable (same as lat pulldown cables) (2)  
Q. Low row cables (long cables) (2)  
R. Adjustable crossover cables (one ball end) (1)  
R1. Crossover cables (two ball ends) (2)  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
Hardware Figure 5. Top assemblies.  
S. Teardrop pulleys (bolt on above lat and seated row benches) (4)  
T. 56” Lat tops (bolt to top of cells with pulleys above lat benches) (2)  
U. 29” Tricep top (bolt on to 56” lat top bar) (1)  
V. Adjustable crossover top (bolt on to 56” lat top bar) (1)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
Hardware Figure 5. Weight stack rubber bumpers.  
W. Weight stack rubber bumpers (inserted under weight stacks)  
Hardware Figure 6. Floating pulleys.  
X. Floating pulleys (bolt to 190 lb cable crossover weight stacks)  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
PARTS LIST  
Part #  
ID  
Description  
Quantity  
Main components  
Cubes  
Low row bench  
Lat bench  
Connecting beam  
Lat top  
Tricep top  
Adj. x-over top  
300 lb weight stack  
190 lb weight stack  
2
2
2
1
2
1
1
1
2
3
4
5
6
7
8
4
4
Cables, caps & nuts  
0017-00103-0234  
Cable jam nut  
Lat pulldown cable  
Tricep cable  
Low row cable  
Adjustable x-over cable  
Crossover cable  
12  
2
1
2
2
M
N
P
Q
R
S
1
6” bolt hardware  
0017-00101-1561  
0017-00104-0363  
0017-00104-0366  
0017-00103-0233  
7/16” x 6” hex head bolt  
7/16” flat washer  
7/16” cap washer  
7/16” Nyloc nut  
8
8
8
8
A
B
C
D
2-3/4” & 3”  
bolt hardware  
0017-00101-1422  
0017-00101-1408  
0017-00042-0969  
0017-00104-0313  
0017-00104-0368  
0017-00103-0217  
3/8” x 3” hex head bolt  
3/8” x 2-3/4” hex head bolt  
End cap  
3/8” flat washer  
3/8” end cap washer  
3/8” Nyloc nut  
6
E
F
G
H
J
24  
66  
66  
66  
33  
K
Pulleys and bumpers  
W
X
0017-00042-0993  
Weight stack rubber bumper  
Floating pulley  
16  
3
Handle and bar  
hardware  
Safety carabiner  
Crossover handle  
Tricep bar  
Lat bar  
Low row handle  
Leg strap  
8
3
1
2
2
1
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SM82 Unpacking & Assembly Instructions  
Pulley hardware  
(installed)  
0017-00101-1413  
0017-00104-0368  
0017-00103-0217  
1-3/4” Bolt  
Cap washer  
3/8” Nyloc nut  
Floating pulley  
hardware (installed)  
0017-00101-1413  
0017-00104-0313  
0017-00103-0217  
1-3/4” Bolt  
Flat washer  
3/8” Nyloc nut  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Kuppersbusch USA Cooktop kc_906 User Manual
Lightolier Work Light C6E17OVW User Manual
Linak Battery Charger 00CH01AUS 00 User Manual
Lincoln Electric Welding System 100SG User Manual
Lopi Stove Yankee PS User Manual
Lowrance electronic Fish Finder LMS 480DF User Manual
Mabe Canada Dishwasher JCP346 User Manual
Makita Saw 5008NB User Manual
McIntosh Stereo Amplifier C2300 User Manual
Mercury Marine Boat 899183001 User Manual