Operating instructions
Combined fridge-freezer
7084376 - 03
230610
CN(es) ... 3
Download from Www.Somanuals.com. All Manuals Search And Download.
General safety information
2 General safety information
Climate
rating
for ambient temperatures of
Danger for the user:
SN
N
10 °C to 32 °C
16 °C to 32 °C
16 °C to 38 °C
16 °C to 43 °C
This appliance is not designed for persons (including children)
with physical, sensory or mental impairment or persons not
having sufficient experience and knowledge, unless they are
instructed in the use of the appliance and are initially super-
vised by a person responsible for their safety. Keep children
under supervision to ensure they do not play with the appli-
ance.
-
ST
T
In case of a fault, pull out the mains plug (not by pulling the
connecting cable) or switch off the fuse.
-
-
1.3 Conformity
The refrigerant circuit has been tested for leaks. The appliance
complies with current safety regulations and EC directives
2006/95/EC and 2004/108/EC.
Have any repairs to or intervention in the appliance, and any
change of the mains power cable, carried out by the customer
service only or by other specialised personnel trained for the
purpose.
When disconnecting the appliance from the supply, always
take hold of the plug. Do not pull the cable.
-
1.4 External dimensions of the appliance
Install and connect the appliance only as instructed.
-
-
Please keep these instructions in a safe place and pass them
on to any subsequent owners.
All repairs to and intervention in the IceMaker may be carried
out only by service personnel or by other skilled personnel
trained for the purpose.*
-
Special-purpose lamps (incandescent lamps, LEDs, fluores-
cent tubes) in the appliance serve to illuminate the appliance
interior and are not suited for room illumination.
-
Fire hazard:
The refrigerant R 600a is environmentally friendly but flam-
-
mable. Escaping refrigerant may ignite.
Do not damage the refrigerant circuit pipes.
•
•
Do not allow naked flames or ignition sources to enter the
appliance.
Do not use any electrical appliances in the interior (e.g.
steam cleaners, heaters, ice cream maker etc.).
If refrigerant escapes: eliminate naked flames or sources
of ignition from the vicinity. Pull out the power plug. Venti-
late the area well. Notify customer service.
•
•
Fig. 2
Model
CN(es) 35..
CN 39..
Height of appliance H (mm)
Do not store explosives or sprays using combustible propel-
lants such as butane, propane, pentane, etc. in the appliance.
Respective spray cans can be identified by reference to the
contents printed on the can or by a flame symbol. Gases
possibly escaping may ignite due to electrical components.
Do not place any burning candles, lamps or other items with
naked flames on or in the appliance.
-
1817
2011
CN(es/esf) 40.. 2011
-
-
Only store high-percentage alcohol in tightly sealed, upright
containers. Alcohol possibly escaping may ignite due to elec-
trical components.
1.5 Saving energy
Always ensure good ventilation. Do not cover ventilation
openings or grille.
-
Danger of tipping and falling:
Always keep fan louvres clear.
-
-
Do not misuse the plinth, drawers, doors etc. as a step or for
-
Do not place appliance in areas of direct sunlight or next to a
support. This applies particularly to children.
stove, heater or similar object.
Danger of food poisoning:
Do not consume food which has been stored too long.
Danger of frostbite, numbness and pain:
The energy consumption depends on the installation condi-
Keep the time the appliance is open to a minimum.
-
-
-
-
-
Store food logically.
Avoid lasting skin contact with cold surfaces or refrigerated/
frozen food or take protective steps, e.g. wear gloves. Do not
consume ice cream, water ice or ice cubes immediately and
do not consume them too cold.
-
Ensure that all food is well packed and covered for storage.
This will prevent frost from forming.
First cool warm food to room temperature before storing it .
-
-
-
Defrost frozen food in the refrigerator.
Please observe the specific information in the other
Empty and switch off refrigerating unit for longer vacation
sections:
periods.
DANGER
identifies a situation involving direct
danger which, if not obviated, may
result in death or severe bodily injury.
Accumulated dust increases the energy
consumption:
Once a year, dust the refrigerating unit
together with the metal grille of the heat
exchanger at the back of the appliance.
-
WARNING identifies a dangerous situation
which, if not obviated, may result in
death or severe bodily injury.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
CAUTION
identifies a dangerous situation
which, if not obviated, may result in
minor or medium bodily injury.
NOTICE
identifies a dangerous situation
which, if not obviated, may result in
damage to property.
Note
identifies useful information and tips.
3 Controls and displays
3.1 Operating and control elements
Fig. 4
u
u
u
Close the upper door.
Pull off the cover Fig. 4 (1) forwards and upwards.
Lift off the cover Fig. 4 (2)
CAUTION
Fig. 3
Risk of injury if the door tips!
(1) On/Off button, refriger-
ator compartment
(6) Setting button, freezer
u
Take good hold of the door.
compartment
(7) SuperFrost buttont
(8) Alarm button
u
Set down the door carefully.
(2) Fan button
(3) Setting button, refriger-
ator compartment
u
Unscrew the upper turn hinge Fig. 4 (3)(2 Torx 25) Fig. 4 (4)
and raise it for removal.
(4) Refrigerator compart-
ment temperature
(9) On/Off button, freezer
u
Lift up the upper door and set it aside.
compartment
display
4.1.2 Detaching the lower door
(5) Freezer compartment
temperature display
u
u
Close the lower door.
Draw the middle bearing pin Fig. 5 (11) out of the turn hinge
and lower door.
3.2 Temperature display
The following are displayed in normal operation:
u
Remove the plastic cap Fig. 5 (10).
the set freezing temperature
-
-
CAUTION
the set cooling temperature
Risk of injury if the door tips!
The freezer compartment temperature display flashes:
u
Take good hold of the door.
u
the temperature setting is being changed
after switch-on the temperature is not yet cold enough
the temperature has risen several degrees
Set down the door carefully.
-
-
-
u
u
u
Open the lower door.
Detach the middle turn hinge Fig. 5 (13).
Lift up the door and set it aside.
4 Putting into operation
4.1.3 Transferring the middle bearing elements
4.1 Changing over the door hinges
Ensure that the following tools are to hand:
Torx 25
q
q
q
q
q
Torx 15
Screwdriver
Cordless screwdriver, if necessary
Second person for fitting work, if needed
4.1.1 Detaching the upper door
Note
u
Remove any food from the door racks before removing the
door, so that no food falls out.
Fig. 5
u
u
Carefully detach the cover panel Fig. 5 (12).
Turn the middle turn hinge Fig. 5 (13) through 180° and screw
it firmly into place on the new hinge side (with 4 Nm).
u
Turn the cover panel Fig. 5 (12) through 180° and snap it into
place again on the new handle side.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Putting into operation
4.1.4 Transferring the lower bearing elements
Fig. 8
Detach the door handles Fig. 8 (32), stoppers Fig. 8 (33) and
pressure plates Fig. 8 (34) and transfer to the opposite side.
When fitting the pressure plates at the opposite side, pay
attention that they engage properly.
u
u
Fig. 6
u
u
u
u
Draw the safety lock Fig. 6 (21).
Remove the cover Fig. 6 (27).*
4.1.6 Fitting the lower door
Fully retract the adjustable-height foot Fig. 6 (22).
u
Place the lower door from above onto the lower bearing pin
If necessary, tip the appliance back a little with the assistance
Fig. 6 (22).
of a second person for removal of the bearing pin.
u
u
Close the door.
u
Pull out the bearing pin Fig. 6 (22) downwards and forwards.
Place the plastic cap Fig. 5 (10) back onto the middle turn
In so doing, pay attention to the hinge bush Fig. 6 (20).
hinge Fig. 5 (13).
u
u
u
Unscrew the turn hinge Fig. 6 (23) (3 Torx 25) Fig. 6 (24).
u
Place the middle bearing pin Fig. 5 (11) in the lower door, on
Unscrew the bearing part Fig. 6 (26)(1 Torx 25), Fig. 6 (28).
the new hinge side, through the middle turn hinge Fig. 5 (13).
Carefully lift off and transfer the cover Fig. 6 (25) on the handle
side.
4.1.7 Fitting the upper door
u
Screw the turn hinge Fig. 6 (23) firmly into place on the new
hinge side, possibly using a cordless screwdriver (with
u
u
Place the upper door on the middle bearing pin Fig. 5 (11).
4 Nm).
Insert the upper turn hinge Fig. 4 (3) in the door on the new
u
Tip the appliance back a
hinge side.
little again and re-insert the
bearing pin Fig. 7 (22). The
notch has to point forwards.
u
Screw the top turn hinge firmly into place (with 4 Nm).(2x Torx
25) Fig. 4 (4). Possibly make preliminary holes with a bradawl
or use a cordless screwdriver.
u
Place the cover Fig. 6 (27)
u
Apply the cover Fig. 4 (1) and cover Fig. 4 (2) to the opposite
on the opposite side.*
side from the outside and snap them into place.
4.1.8 Aligning the doors
u
If necessary, align the doors to the appliance housing by way
of the two oblong holes in the lower turn hinge Fig. 6 (23) and
middle turn hinge Fig. 5 (13). To do so, unscrew the middle
screw in the lower turn hinge Fig. 6 (23).
Fig. 7
CAUTION
WARNING
Risk of injury if the door tips!
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly enough, the
door may drop out. This may lead to severe injuries. What is
more, the door may not close and therefore the appliance may
fail to cool properly.
u
The safety lock (21) has to engage with the turn hinge at the
side so that the bearing pin and therefore the door are
secured.
u
u
Screw the turn hinges firmly into place with 4 Nm.
u
Check all of the screws and retighten if necessary.
u
u
Snap the safety lock (21) onto the turn hinge again.
Put on the hinge bush Fig. 6 (20).
4.1.5 Transferring the handles
u
Disengage the spring clip Fig. 8 (31) from the upper door and
transfer it to the new hinge side.
u
Lift the stoppers Fig. 8 (30) out of the door bearing bushes and
transfer them.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Putting into operation
4.2 Insertion into a row of kitchen units
WARNING
Fire hazard due to dampness!
If live parts or the mains lead become damp this may cause short
circuits.
u
The appliance is designed for use in enclosed areas. Do not
operate the appliance outdoors or in areas where it is exposed
to splash water or damp conditions.
WARNING
Fire hazard due to refrigerant!
The refrigerant R 600a is environmentally friendly but flammable.
Escaping refrigerant may ignite.
u
Do not damage the piping of the refrigeration circuit.
WARNING
Fig. 9
Fire hazard and danger of damage!
(1) Stack cabinet
(3) Kitchen cabinet
u
Do not place appliances emitting heat e.g. microwaves,
(2) Appliance
(4) Wall
toasters etc. on the appliance!
The appliance can be inserted into a row of kitchen units. To
match the appliance Fig. 9 (2) to the height of the row of units, a
suitable stack cabinet Fig. 9 (1) can be fitted above the appliance.
When inserting the appliance into a row of standard kitchen units
(max. depth 580 mm), the appliance can be installed directly next
to the kitchen unit Fig. 9 (3). The appliance door projects relative
to the front of the kitchen unit by 34 mm at the side and by
50 mm in the middle of the appliance. It can be opened and
closed perfectly as a result.
WARNING
Fire hazard and risk of damage due to blocked ventilation grille!
u
Always keep the ventilation grille free. Always ensure that the
appliance is properly ventilated.
u
Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because other-
wise there will be vibratory noise!
Important for the ventilation:
At the back of the stack cabinet there has to be a ventilation
u
-
Remove the protective film from the outside of the appli-
duct of at least 50 mm depth throughout the width of the stack
cabinet.
ance.*
The ventilation space under the ceiling has to be at least
-
NOTICE*
300 cm2.
The stainless steel doors are provided with a high-quality surface
coating and must not be treated using the accompanying care
product.
If the appliance is installed with the hinges next to a wall
Fig. 9 (4), the distance between appliance and wall has to be at
least 36 mm. This corresponds to the projection of the handle
when the door is open.
Otherwise the surface coating will be affected.
u
u
Wipe the coated door surfaces using a soft, clean cloth only.
Apply a stainless steel cleaner only to the stainless steel
4.3 Transporting the appliance
side wallsevenly, wiping with the grain. Subsequent cleaning
becomes easier as a result.
u
Wipe side walls with a paint finish using a soft, clean cloth
CAUTION
only.
Risk of injury and danger of damage as a result of incorrect trans-
port!
u
Remove the protective film from the decorative trims and
u
Transport the appliance in a packed condition.
drawer fronts.*
u
u
Transport the appliance upright.
u
u
Remove all transit supports.
Do not transport the appliance without assistance.
Dispose of packaging material (see 4.5) .
NOTICE
4.4 Installing the appliance
Risk of damage due to condensate!
u
Do not install the appliance directly alongside a further refrig-
In the event that the appliance is damaged, contact the supplier
erator/freezer.
immediately before connecting to the mains.
The floor at the site must be flat and level.
u
Align the appliance so that it
Do not install the appliance in a location where it is exposed to
stands firmly and on a level by
applying the accompanying
spanner to the adjustable-
height feet (A) and using a spirit
level.
direct radiation of the sun, next to a cooker, heater and similar.
Always install the appliance directly against the wall.
Do not install the appliance without assistance.
Standard EN 378 specifies that the room in which you install your
appliance must have a volume of 1 m2 per 8 g of R 600a refrig-
erant used in the appliance. If the room in which the appliance is
installed is too small, a flammable gas-air mixture may form in the
event of a leakage in the refrigeration circuit. The quantity of
refrigerant used in your appliance is indicated on the type plate
on the inside of the appliance.
u
Then support the door: Extend
the adjustable foot at the turn
hinge (B) until it rests on the
floor and then make a further
90° turn.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Control
w
w
If the appliance is installed in a very damp environment, conden-
sate may form on the outside of the appliance.
The interior light is on when the door is open.
The temperature display shines. Refrigerator compartment
and freezer compartment are switched on.
u
Always see to good ventilation at the installation site.
4.5 Disposing of packaging
5 Control
5.1 Door alarm
WARNING
Danger of suffocation due to packing material and plastic film!
For refrigerator and freezer compartment
u
Do not allow children to play with packing material.
If the door is open longer then 60 s, the audible alarm sounds.
The packaging is made of recyclable materials:
The audible alarm is automatically silenced when the door is
closed.
corrugated board/cardboard
-
-
-
expanded polystyrene parts
5.1.1 Muting the door alarm
polythene bags and sheets
The audible alarm can be muted when the door is open. The
polypropylene straps
-
sound switch-off function is active as long as the door is left open.
u
Take the packaging material to an official collecting point.
u
w
Press alarm button Fig. 3 (8).
The door alarm is silenced.
4.6 Connecting the appliance
5.2 Temperature alarm
NOTICE
Risk of damage to the electronic control system!
The audible alarm sounds if the freezer temperature is not cold
u
Do not use stand-alone inverters (conversion of d.c. to a.c./
enough.
three-phase) or energy saving plugs.
The alarm button flashes at the same time.
The cause of the temperature being too high may be:
warm fresh food was placed inside
-
-
WARNING
too much warm ambient air flowed in when rearranging and
Fire and overheating hazard!
removing food
u
Do not use extension cables or multiple socket outlets.
power failure for some time
-
-
the appliance is faulty
The type of current (alternating current) and voltage at the instal-
lation site have to conform with the data on the type plate (see
Appliance at a glance).
The audible alarm is automatically silenced, the alarm button
Fig. 3 (8) goes out and the temperature display stops flashing
when the temperature is sufficiently cold again.
Connect the appliance only with a properly installed
socket outlet with earthing contact. The socket outlet
must be fused with 10 A or higher.
If the alarm status persists: (see Malfunction).
It must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emer-
gency.
Note
Food may be spoilt if the temperature is not cold enough.
u
Check the quality of the food. Do not consume spoiled food.
u
Check the electrical connection.
u
5.2.1 Muting the temperature alarm
u
Plug in the power plug.
The audible alarm can be muted. When the temperature is suffi-
ciently cold again, the alarm function is active again.
4.7 Switching on the appliance
u
Press alarm button Fig. 3 (8).
w
The audible alarm is silenced.
Note
u
To switch on the entire appliance it is necessary only to switch
on the freezer compartment. In so doing, the refrigerator
compartment is automatically switched on as well.
5.3 Refrigerator compartment
The natural circulation of air in the refrigerator compartment
results in zones differing in temperature. It is coldest directly
above the vegetable drawers and at the rear wall. It is warmest
at the top front of the compartment and in the door.
Put the appliance into operation about 2 hours before first loading
food to be frozen.
4.7.1 Switching on the freezer compartment
5.3.1 Food refrigeration
u
w
PressOn/Off button, freezer compartment Fig. 3 (9).
The appliance is switched on. The refrigerator compartment
Note
temperature display indicates the set temperature. The
freezer compartment temperature display and the alarm
button flash until the temperature is sufficiently low.
The energy consumption increases and the cooling performance
decreases if the ventilation is inadequate.
u
Always keep the air slits of the fan free.
4.7.2 Switching on the refrigerator compart-
ment
u
Store perishable food such as ready-to-serve dishes, meat
products and sausages in the coldest zone. Place butter and
preserves in the upper area and in the door (see Appliance
at a glance).
Note
u
Use recyclable plastic, metal, aluminium and glass containers
u
When the refrigerator compartment is switched on, the freezer
and cling film for wrapping.
compartment is automatically switched on as well.
u
Press On/Off button, refrigerator compartment Fig. 3 (1).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Control
u
Use the front area of the refrigerator compartment floor only
5.3.5 Using the sectioned shelf
for briefly putting down cooled products, e.g. when rear-
ranging and sorting. However do not leave cooled products
there otherwise they may be pushed back or tipped over when
the door is closed.
u
Do not store food too close together to enable good air circu-
lation.
u
To safeguard bottles from tipping over: move the bottle holder.
5.3.2 Setting the temperature
The temperature depends on the following factors:
Fig. 10
the door opening frequency
-
-
u
The glass shelf with stop face (2) has to be at the back.
the room temperature at the site where the appliance is
installed
5.3.6 Moving the storage rack
the type, temperature and quantity of frozen food
-
Temperature setting to be recommended: 5 °C
The temperature can be changed continuously. Once the 1 °C
setting is reached, it starts again with 9 °C.
u
To access temperature adjustment: press the setting button,
refrigerator compartment Fig. 3 (3) once.
u
Press the setting button, refrigerator compartment Fig. 3 (3)
the number of times needed until the required temperature
shines in the LED display.
*
*
u
Remove storage rack according to
Note
illustration.
u
Long pressing of the setting button sets a slightly colder value
within a small temperature range (e.g.: between "5" and "7"),
but it is not visible in the display.
5.3.3 Fan
With the fan you can rapidly cool large quantities of fresh food or
achieve a relatively even distribution of temperature across all
the storage levels.
The boxes can be removed and placed on the table as a single
unit.*
The forced-air cooling is to be recommended:
Only one box or both boxes can be used. If particularly tall bottles
are to be stored, attach only the wide box above the bottle
rack.*
at high room temperature (from approx. 30 °C )
-
at high humidity
-
The forced-air cooling uses slightly more energy. To save
energy, the fan switches off automatically when the door is open.
Three small boxes are available through the customer service as
optional equipment instead of one wide and one small box.*
u
Re-positioning the boxes: Lift them for
Switching on the fan
removal and re-position them as
required.*
u
w
w
Briefly press the fan button Fig. 3 (2).
The fan button shines.
The fan is active. It switches on automatically when the
*
compressor runs.
u
To detach lid: Open 90° and raise to
To switch off the fan
disengage.*
u
w
w
Briefly press the fan button Fig. 3 (2).
The fan button goes out.
The fan is switched off.
*
5.3.4 Relocating the shelves
5.3.7 Removing the bottle holder*
The shelves have stops preventing them from being unintention-
ally pulled out.
u
Lift the shelf and draw it out forwards.
u
Always take hold of the bottle holder
on the plastic part.
u
w
Insert shelf with the raised edge pointing upwards at the back.
The food does not freeze onto the rear wall.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Control
In case of the maximum amount of food to be frozen (see type
5.4 Freezer compartment
plate):
u
u
w
w
w
wait about 24 h.
You can store frozen food, make ice cubes and freeze fresh food
in the freezer compartment.
Place food in the drawers.
SuperFrost is automatically deactivated after about 65 h.
The SuperFrost button is dark.
5.4.1 Freezing food
The maximum weight of fresh food which can be frozen within 24
h is indicated on the type plate under "freezing capacity ... kg/
24h".
The appliance continues to operate in the energy-saving,
normal mode.
5.4.5 Drawers
The maximum load of frozen food for the drawers is 25 kg each
Note
and for the shelves 35 kg each.
The energy consumption increases and the cooling performance
decreases if there is insufficient ventilation.
For appliances with NoFrost:
CAUTION
u
u
Leave the bottom drawer in the appliance!
Risk of injury due to broken glass!
Always keep the air slits of the fan free at the rear wall!
Bottles and cans containing drinks may burst when being frozen.
This applies particularly to sparkling drinks.
u
Do not freeze bottles and cans containing drinks!
In order that the food is rapidly frozen through to the core, do not
exceed the following quantities per pack:
-
Fruit, vegetables up to 1 kg
-
Meat up to 2.5 kg
u
Pack the food in portions in freezer bags, reusable plastic,
metal or aluminium containers.
u
To store frozen food directly on the shelves: pull the drawer
forwards and lift it out.
5.4.2 Thawing food
5.4.6 Shelves
-
in the refrigerator compartment
u
To remove the shelf: lift up at the front and
-
at room temperature
pull out.
-
in a microwave oven
u
To put the shelf back: simply push in as far
-
in a conventional or fan oven
Food once thawed should be re-frozen only in exceptional
cases.
as it will go.
u
5.4.3 Setting the temperature
Temperature setting to be recommended: -18 °C
5.4.7 VarioSpace*
The temperature can be changed continuously. Once the
Apart from being able to remove
the drawers, you can also remove
the shelves, creating space for
large items of frozen food.
Poultry, meat, large pieces of
game and high bakery products
can be frozen in one piece and
prepared.
-32 °C setting is reached, it starts again with -15 °C.
u
To access temperature adjustment: press setting button,
freezer compartment Fig. 3 (6) once.
u
Press the setting button, freezer compartment Fig. 3 (6) the
number of times needed until the required temperature shines
in the LED display.
Note
u
u
Long pressing of the setting button sets a slightly colder value
The maximum load of frozen
within a small temperature range (e.g.: between -15 °C and
-18 °C) but it is not visible in the display.
food for the drawers is 25 kg
each and for the shelves
35 kg each.
5.4.4 SuperFrost
With this function you can freeze fresh food quickly through to
the core. The appliance operates with maximum refrigeration.
The noise of the refrigeration unit may be temporarily louder as
a result.
5.4.8 Information system*
The maximum amount of fresh food which can be frozen in 24 h
is indicated on the type plate under "freezing capacity ... kg/
24h". This amount varies according to the model and climate
rating.
Freezing with SuperFrost
You do not have to activate SuperFrost in the following cases:
Fig. 11
(1) Ready-made meals, ice
cream
(4) Sausages, bread
-
when placing frozen food in the freezer
Briefly press the SuperFrost button Fig. 3 (7).
The SuperFrost button shines.
u
w
w
(2) Pork, fish
(5) Game, mushrooms
(3) Fruit, vegetables
(6) Poultry, beef/veal
The freezer temperature drops, the appliance operates with
the maximum refrigerating capacity.
In case of a small amount of food to be frozen:
wait about 6 h.
The figures indicate the storage time in months for several types
of frozen food in each case. Storage times given are guide times.
u
u
Place the fresh food in the top drawers.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Control
u
Place the filled water tank in
the holder and slide it all the
way back.
5.4.9 Cold storage accumulators
The cold storage accumulators prevent the temperature from
rising too fast in the event of power failure.
Using cold storage accumulators
u
Place the cold storage accumula-
tors in the top freezer compart-
ment to save space.
u
Place the frozen cold storage
accumulators on the frozen food
in the upper front area of the
freezer compartment.
Note
u
The water reservoir has to be slid all the way into the bracket
provided for the purpose in the refrigerator compartment!
5.4.10 IceMaker*
The IceMaker and the water reservoir situated in the refrigerator
compartment can be used to produce ice cubes or to provide
chilled drinking water.
Switching on the IceMaker*
The IceMaker is in the top drawer of the freezer compartment.
The drawer is marked "IceMaker".
Make certain that the following conditions are met:
The appliance is level.
-
-
-
-
The appliance is connected.
Fig. 12
The freezer compartment is switched on.
The water tank was cleaned with water and is filled.
u
u
Pull out the drawer.
Press the On/Off button Fig. 12 (1) so that the LED
Fig. 12 (2) shines.
Filling the water tank*
u
Push in the drawer.
Note
WARNING
u
The IceMaker produces ice cubes only if the drawer is fully
Risk of poisoning!
closed.
u
The water quality has to comply with the drinking water ordi-
nance of the respective country (e.g. 98/8
Switching off the IceMaker*
u
The IceMaker serves exclusively for making ice cubes in
If no ice cubes are needed, the IceMaker can be switched off
household quantities and has to be operated with water suit-
able for the purpose.
independently of the freezer compartment.
When the IceMaker is switched off, the IceMaker drawer can also
be used for freezing and storing food.
NOTICE
u
Press the On/Off button for about 1 second until the LED goes
Risk of damage to the IceMaker!
out.
Liquids containing sugar, such as soft drinks, fruit juices or
similar, gum up the pump and therefore lead to total pump failure
and, as a consequence, to damage to the IceMaker.
u
w
Clean the IceMaker.
This ensures that no water or ice remains in the IceMaker.
u
Fill the water reservoir with drinking water only! Do not use any
Producing ice cubes*
liquids containing sugar, such as soft drinks, fruit juices or
similar!
The production capacity depends on the freezer temperature.
The lower the temperature, the more ice cubes can be produced
in a specific period.
The ice cubes drop from the IceMaker into the drawer. When a
certain filling level has been reached, no further ice cubes are
produced. The IceMaker does not fill the drawer right up to the
brim.
If large quantities of ice cubes are needed, the complete
IceMaker drawer can be exchanged for the adjacent drawer.
When the drawer is closed, the IceMaker automatically re-
commences production.
The IceMaker is supplied with water from a water tank in the
refrigerator compartment (see Appliance at a glance).
Before initial operation:
u
clean the water tank thoroughly with water to remove any dust
etc.
u
Pull the water tank forwards.
u
Open the front flap and fill the
tank with water.
Once the IceMaker has been switched on for the first time, it may
take up to 24 hours until the first ice cubes are produced.
Note
When the appliance is used for the first time or if has not been
used for a long time, the IceMaker has to be rinsed to remove any
particles present.
u
Therefore do not use or consume the ice cubes made in the
first 24 hours.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
u
To clean the drain opening: remove
any deposits with a fine instrument,
e.g. a cotton bud.
6 Maintenance
6.1 Defrosting with NoFrost
The NoFrost system automatically defrosts the appliance.
Refrigerator compartment:
Items of equipment:
u
Clean items of equipment by hand with lukewarm water and
a little washing-up liquid.
The defrost water evaporates due to the compressor heat. Drops
of water on the rear wall are perfectly normal.
u
For cleaning, remove the support rails for the half-sized glass
shelves.
u
Regularly clean the drain opening to allow the water to flow
Freezer compartment:
The moisture condenses on the evaporator, is periodically
defrosted and evaporates.
u
The appliance does not have to be manually defrosted.
*
To dismantle the shelves: remove
the trims and side parts.*
6.2 Cleaning the appliance
u
u
Before cleaning:
To dismantle the storage rack:
remove the protective film from the
decorative trims.*
CAUTION
Risk of injury and damage as a result of hot steam!
Hot steam may damage the surfaces and cause burns.
u
Do not use any steam cleaners!
*
Lift out the boxes and lift the covers
for removal.*
u
u
NOTICE
Incorrect cleaning damages the appliance!
u
u
u
Do not use cleaning agents in concentrated form.
Do not use any scouring or abrasive sponges or steel wool.
*
To empty the water collecting tray:
Remove the water tank. Carefully
disengage the tray forwards and
then lower for removal.*
Do not use any cleaning agents containing sand, chloride,
chemicals or acid.
u
u
Do not use chemical solvents.
Do not damage or remove the type plate on the inside of the
appliance. It is important for the customer service.
u
u
Do not pull off, bend or damage cables or other components.
Do not allow any cleaning water to enter the drain channel,
ventilation grille or electrical parts.
u
u
Empty the appliance.
Pull out the plug.
*
-
Use soft cleaning cloths and a multi-purpose
cleaning agent with neutral pH value.
After cleaning:
-
Only use food compatible cleaning and care agents
on the inside of the appliance.
u
u
u
Wipe dry the appliance and items of equipment.
Connect the appliance and switch it on again.
Switch on SuperFrost (see 5.4.4) .
u
w
Regularly clean ventilation grilles.
Dust deposits increase energy consumption.
When the temperature is sufficiently cold:
Put the food back inside.
u
Outside surfaces and interior:
u
Clean the plastic surfaces, outside and inside, by hand using
lukewarm water and a little washing-up liquid.
6.3 Cleaning the IceMaker*
NOTICE*
The stainless steel doors are provided with a high-quality surface
coating and must not be treated using the accompanying care
product.
Otherwise the surface coating will be affected.
u
Wipe the coated door surfaces using a soft, clean cloth only.
In case of stubborn dirt, use a little water or a neutral cleaning
agent. A microfibre cloth can be optionally used.
Fig. 13
u
If the stainless steel side walls are dirty, clean them using
a commercially available stainless steel cleaning agent. Then
evenly apply the accompanying stainless steel care product,
making strokes in the direction of the grain.
The IceMaker has to be switched on.
u
u
u
Pull out the drawer and remove the ice cubes.
Clean the drawer with warm water and mild washing-up liquid.
When the drawer is pulled out, hold down the On/Off button
(about 10 seconds).
u
Wipe side walls with a paint finish using a soft, clean cloth
only. In case of stubborn dirt, use a little water or a neutral
cleaning agent. A microfibre cloth can be optionally used.
w
w
u
w
After about 1 s the LED goes out, the IceMaker is switched off.
After about 10 s the LED flashes for about 60 s.
Slide in the drawer while the LED is flashing.
The ice-cube tray of the IceMaker turns to a skew position.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Malfunction
u
u
Remove the drawer.
this case you will have to be charged for the costs incurred, even
Clean the ice cube tray with warm water. If necessary, use mild during the warranty period. You may be able to rectify the
washing-up liquid. Then rinse.
following faults yourself:
Switch the IceMaker on again.
Appliance does not work.
u
w
u
Press the ON/OFF button until the LED shines, then slide in
the drawer.
The appliance is not switched on.
Switch on the appliance.
→
u
The IceMaker starts producing ice cubes.
If washing-up liquid was used:
The power plug is not properly inserted in the wall socket.
Check power plug.
→
u
throw away the first three loads of ice cubes to get rid of any
remaining washing-up liquid.
The fuse of the wall socket is not in order.
Check fuse.
→
u
6.4 Changing the interior light with bulb
The compressor runs for a long time.
The compressor switches to a low speed when little cold is
needed. Although the running time is increased as a result,
energy is saved.
→
Bulb data
max. 25 W
Fitting: E14
This is normal in energy-saving models.
u
Type of current and voltage must conform with the details on
SuperFrost is activated.
→
the type plate
The compressor runs for longer in order to rapidly cool the
u
u
u
Switch off the appliance.
food. This is normal.
Pull out the power plug or
Excessive noise.
switch off the fuse.
Speed-controlled* compressors may produce varying
running noise due to different speed steps.
The sound is normal.
→
u
Take holder of the cover
Fig. 14 (1) at the front and
u
unhook it at the back.
u
Change
the
bulb
A bubbling and gurgling noise.
Fig. 14 (2).
This noise comes from the refrigerant flowing in the refriger-
→
u
Put the cover Fig. 14 (1)
back in place.
ation circuit.
The sound is normal.
u
A quiet clicking noise.
Fig. 14
The noise is produced whenever the refrigeration unit (motor)
automatically switches on or off.
→
6.5 Customer service
First check whether you can correct the fault yourself by refer-
ence to the list (see Malfunction). If this is not the case, please
contact the customer service whose address is given in the
enclosed customer service list.
The sound is normal.
u
A hum. It is briefly a little louder when the refrigeration unit
(the motor) switches on.
The refrigeration increases automatically when the Super-
→
Frost, function is activated, fresh food has just been placed
in the appliance or the door has been left open for a while.
The sound is normal.
u
The ambient temperature is too high.
→
WARNING
Risk of injury if repair work is not carried out professionally!
u
u
Have any repairs to and intervention in the appliance and
A low hum.
mains power cable, which are not expressly mentioned in the
(see Maintenance) carried out by the customer service only.
The sound is produced by air flow noise of the fan.
→
The sound is normal.
u
u
Read the appliance
Vibratory noise.
designation
The appliance is not standing firmly on the floor. As a result,
adjoining units or objects are set into vibration by the running
refrigeration unit.
→
Fig. 15 (1), service
No. Fig. 15 (2) and
serial No. Fig. 15 (3) off
the type plate located
inside the appliance
on the left-hand side.
u
u
Move the appliance away a little and align it using the adjust-
able feet.
Move bottles and containers apart.
Hum of the water tank pump.*
When water is pumped out of the water reservoir, a brief hum
of the pump can be heard.
→
The sound is normal.
u
Fig. 15
u
Notify the customer service, specifying the fault, appliance
The SuperFrost button flashes together with the tempera-
ture display.
designation Fig. 15 (1), service No. Fig. 15 (2) and serial No.
Fig. 15 (3).
There is a fault.
→
w
This will help us to provide you with a faster and more accurate
Contact the customer service. (see Maintenance).
u
service.
The IceMaker cannot be switched on. *
u
w
u
Keep the appliance closed until the customer service arrives.
The appliance and therefore the IceMaker are not connected.
Connect the appliance. (see Putting into operation).
→
The food will stay cool longer.
u
Pull out the mains plug (not by pulling the connecting cable)
or switch off the fuse.
The IceMaker does not make any ice cubes.*
The IceMaker is not switched on.
Switch on the IceMaker.
→
u
7 Malfunction
The drawer of the IceMaker is not properly closed.
Close the drawer properly.
The water tank is not correctly inserted.
→
Your appliance is designed and manufactured for a long life span
and reliable operation. If a malfunction nonetheless occurs
during operation, check whether it is due to a handling error. In
u
→
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Decommissioning
Insert the water tank.
There is not enough water in the water tank.
Fill the water tank.
u
8.2 Taking the appliance out of service
→
u
Empty the appliance.
u
u
Put the IceMaker in the cleaning position (see Mainte-
The LED of the IceMaker flashes.*
nance).
There is not enough water in the water tank.
Fill the water tank.
→
u
u
Pull out the power plug.
u
If the LED flashes and the water tank is full, the IceMaker is
→
defective.
u
Leave the door open to prevent odour.
Contact the customer service. (see Maintenance).
u
The temperature is not cold enough.
The door of the appliance is not properly closed.
Close the door of the appliance.
Insufficient ventilation.
→
9 Disposing of the appliance
u
The appliance contains some reusable materials
and should be disposed of properly - not simply with
unsorted household refuse. Appliances which are no
longer needed must be disposed of in a professional
and appropriate way, in accordance with the current
local regulations and laws.
→
Clear ventilation grilles.
u
The ambient temperature is too high.
The appliance was opened too frequently or for too long.
→
u
→
Wait until the appliance reaches the required temperature
itself. If not, contact the customer service. (see Mainte-
nance).
u
When disposing of the appliance, ensure that the refrigeration
circuit is not damaged to prevent uncontrolled escape of the
refrigerant it contains (data on type plate) and oil.
Too much fresh food was placed inside without SuperFrost.
→
u
u
u
Disable the appliance.
The appliance is too close to a heat source.
Solution: (see Putting into operation).
u
Pull out the plug.
→
Cut through the connecting cable.
u
The interior light is not on.
The appliance is not switched on.
Switch on the appliance.
→
u
The door was open longer than 15 min.
→
The interior light automatically switches off if the door has
u
been open for about 15 min.
If the interior light is not on but the temperature display is lit,
the bulb is faulty.
→
Change the bulb. (see Maintenance).
u
8 Decommissioning
8.1 Switching off the appliance
Note
u
To switch on the entire appliance it is necessary only to switch
off the freezer compartment. In so doing, the refrigerator
compartment is automatically switched off as well.
8.1.1 Switching off the freezer compartment
u
Press ON/OFF button, freezer compartment Fig. 3 (9) for at
least 3 seconds.
w
The temperature displays are dark. The entire appliance is
switched off.
8.1.2 Switching off the refrigerator compart-
ment
u
Press ON/OFF button, refrigerator compartment Fig. 3 (1) for
at least 3 seconds.
w
w
The interior light is off.
The temperature display of the refrigerator compartment is
dark.
Note
u
If only the refrigerator compartment is to be switched off, e.g
during holidays, then always pay attention: the freezer
compartment temperature display has to shine.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Disposing of the appliance
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|