Operating instructions
Freezer
7084644 - 00
230311
SGN(es)/GN(es) ... 6
Download from Www.Somanuals.com. All Manuals Search And Download.
General safety information
Accumulated dust increases the energy
Note
Compliance with the ambient temperatures indicated is
consumption:
u
Once a year, dust the refrigerating unit
required, otherwise the cooling performance is reduced.
-
together with the metal grille of the heat
exchanger at the back of the appliance.
Climate
rating
for ambient temperatures
SN, N
ST
up to 32 °C
up to 38 °C
up to 43 °C
1.6 Insulation plate
The insulation plate for part-load operation is available as an
T
accessory from specialist dealers.
If you do not store much food in the appli-
ance, you can reduce the power consump-
tion by as much as 50 % by using the insu-
lation plate. Up to 5 drawers can be de-
energised, depending on model. At least 3
drawers are necessary for cooling. More
information accompanies the insulation
plate.
The appliance will function properly in ambient temperatures of
down to 5 °C.
1.3 Conformity
The refrigerant circuit has been tested for leaks. The appliance
complies with current safety regulations and EC directives
2006/95/EC and 2004/108/EC.
1.4 External dimensions of the appli-
ance
1.7 HomeDialog
Depending on model and options, the Home-
Dialog system can be used to network a number
of Liebherr appliances (situated, for example, in
the basement) with a main appliance (sited, for
example, in the kitchen) and control them via the
latter. You will find more information on the
benefits, requirements and principle of operation
2 General safety information
Danger for the user:
This appliance is not designed for persons (including chil-
dren) with physical, sensory or mental impairment or
persons not having sufficient experience and knowledge,
unless they are instructed in the use of the appliance and
are initially supervised by a person responsible for their
safety. Keep children under supervision to ensure they do
not play with the appliance.
-
Fig. 2
Model
Height of appliance H (mm)
1655
SGNes 27..,
SGN 27..
In case of a fault, pull out the mains plug (not by pulling the
connecting cable) or switch off the fuse.
-
-
SGNes 30..,
1852
SGN 30.., GN 30..,
GNes 30..
Have any repairs to or intervention in the appliance, and any
change of the mains power cable, carried out by the
customer service only or by other specialised personnel
trained for the purpose.
1.5 Saving energy
When disconnecting the appliance from the supply, always
take hold of the plug. Do not pull the cable.
-
Always ensure good ventilation. Do not cover ventilation
-
-
-
Install and connect the appliance only as instructed.
-
-
openings or grille.
Please keep these instructions in a safe place and pass
Do not place appliance in areas of direct sunlight or next to a
stove, heater or similar object.
them on to any subsequent owners.
Special-purpose lamps (incandescent lamps, LEDs, fluores-
cent tubes) in the appliance serve to illuminate the appliance
interior and are not suited for room illumination.
-
The energy consumption depends on the installation condi-
Keep the time the appliance is open to a minimum.
-
-
Fire hazard:
The lower the temperature setting, the higher the power
consumption.
The refrigerant R 600a is environmentally friendly but flam-
-
Store food logically. (see Appliance at a glance).
mable. Escaping refrigerant may ignite.
-
-
Ensure that all food is well packed and covered for storage.
Do not damage the refrigerant circuit pipes.
•
This will prevent frost from forming.
Do not allow naked flames or ignition sources to enter the
appliance.
•
First cool warm food to room temperature before storing it .
-
Do not use any electrical appliances in the interior (e.g.
steam cleaners, heaters, ice cream maker etc.).
•
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
If refrigerant escapes: eliminate naked flames or sources The temperature display flashes:
•
of ignition from the vicinity. Pull out the power plug. Venti-
late the area well. Notify customer service.
the temperature setting is being changed
after switch-on the temperature is not yet cold enough
the temperature has risen several degrees
-
-
-
Do not store explosives or sprays using combustible propel-
lants such as butane, propane, pentane, etc. in the appli-
ance. Respective spray cans can be identified by reference
to the contents printed on the can or by a flame symbol.
Gases possibly escaping may ignite due to electrical
components.
-
Dashes flash in the display:
the freezer temperature is above 0 °C.
-
The following displays indicate malfunction. Possible causes
Keep burning candles, lamps and other items with naked
flames away from the appliance so that they do not set the
appliance on fire.
-
-
and corrective action (see Malfunction).
F0 to F9
-
-
Only store high-percentage alcohol in tightly sealed, upright
containers. Alcohol possibly escaping may ignite due to
electrical components.
The power failure symbol
shines.
Danger of tipping and falling:
4 Putting into operation
Do not misuse the plinth, drawers, doors etc. as a step or for
-
support. This applies particularly to children.
4.1 Transporting the appliance
Danger of food poisoning:
Do not consume food which has been stored too long.
-
Danger of frostbite, numbness and pain:
CAUTION
Avoid lasting skin contact with cold surfaces or refrigerated/
frozen food or take protective steps, e.g. wear gloves. Do
not consume ice cream, water ice or ice cubes immediately
and do not consume them too cold.
-
Risk of injury and danger of damage as a result of incorrect
transport!
Transport the appliance in a packed condition.
Transport the appliance upright.
u
u
u
Please observe the specific information in the other
Do not transport the appliance without assistance.
sections:
4.2 Installing the appliance
DANGER
identifies a situation involving direct
danger which, if not obviated, may
result in death or severe bodily
injury.
In the event that the appliance is damaged, contact the supplier
immediately before connecting to the mains.
The floor at the site must be flat and level.
WARNING identifies a dangerous situation
which, if not obviated, may result in
death or severe bodily injury.
Do not install the appliance in a location where it is exposed to
direct radiation of the sun, next to a cooker, heater and similar.
The ideal installation site is a dry, well ventilated room.
CAUTION
identifies a dangerous situation
which, if not obviated, may result in
minor or medium bodily injury.
Always install the appliance with the back directly against the
wall.
Do not install the appliance without assistance.
NOTICE
identifies a dangerous situation
which, if not obviated, may result in
damage to property.
Standard EN 378 specifies that the room in which you install
your appliance must have a volume of 1 m2 per 8 g of R 600a
refrigerant used in the appliance. If the room in which the appli-
ance is installed is too small, a flammable gas-air mixture may
form in the event of a leakage in the refrigeration circuit. The
quantity of refrigerant used in your appliance is indicated on the
type plate on the inside of the appliance.
Note
identifies useful information and tips.
3 Controls and displays
The appliance may be moved only when it is empty.
3.1 Operating and control elements
WARNING
Fire hazard due to dampness!
If live parts or the mains lead become damp this may cause
short circuits.
The appliance is designed for use in enclosed areas. Do not
operate the appliance outdoors or in areas where it is
exposed to splash water or damp conditions.
u
Fig. 3
(1) Up setting button
(2) Down setting button
(3) Menu symbol
(7) On/Off button
(8) SuperFrost button
(9) Alarm button
WARNING
Fire hazard due to refrigerant!
(4) Alarm symbol
(10)Power failure symbol
(11)Child-proofing symbol
(12)HomeDialog symbol
The refrigerant R 600a is environmentally friendly but flam-
mable. Escaping refrigerant may ignite.
(5) SuperFrost symbol
(6) Temperature display
Do not damage the piping of the refrigeration circuit.
u
3.2 Temperature display
The following are displayed in normal operation:
the warmest freezing temperature
-
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Putting into operation
NOTICE
Risk of damage to side-by-side appliances due to condensa-
tion!
WARNING
Fire hazard and danger of damage!
When a side-by-side appliance (S…) is fitted together with a
second appliance (as a SBS combination), the door hinges
must remain as delivered.
Do not place appliances emitting heat e.g. microwaves,
toasters etc. on the appliance!
u
Do not change over the door hinges.
u
Ensure that the following tools are to hand:
WARNING
Torx® 25
q
q
q
q
q
q
Blocked ventilation openings pose a risk of fire and damage!
Torx® 15
Always keep the ventilation openings clear. Always ensure
that the appliance is properly ventilated!
u
u
u
Screwdriver
Cordless screwdriver, if necessary
Second person for fitting work, if needed
Accompanying Allen key size 2*
Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because other-
wise there will be vibratory noise!
Remove the protective film from the outside of the appli-
ance.*
4.3.1 Detaching the door
NOTICE
The stainless steel doors are provided with a high-quality
surface coating and must not be treated using the accompa-
nying care product.
Otherwise the surface coating will be affected.
Wipe the coated door surfaces using a soft, clean cloth
only.
u
Apply a stainless steel cleaner only to the stainless steel
side walls evenly, wiping with the grain. Subsequent
cleaning becomes easier as a result.
u
Wipe side walls with a paint finish using a soft, clean
cloth only.
u
Remove all transit supports.
u
u
Dispose of packaging material (see 4.5) .
Fig. 4
Close the door.
u
u
u
NOTICE
Pull off the cover Fig. 4 (10) forwards and upwards.
Lift off the cover Fig. 4 (11).
Risk of damage due to condensate!
If your appliance is not a Side-by-Side (SBS) appliance:
do not install the appliance directly alongside a further refrig-
erator/freezer.
u
u
CAUTION
Align the appliance so that it
stands firmly and on a level by
applying the accompanying
spanner to the adjustable-
height feet (A) and using a
spirit level.
Risk of injury if the door tips!
Take good hold of the door.
Set down the door carefully.
u
u
Unscrew the upper turn hinge Fig. 4 (12)(2x Torx® 25)
Fig. 4 (13) and lift it off.
u
u
Lift off the door and set it aside.
4.3.2 Distinguishing between bearing elements
Some appliances are height-adjustable, as can be noted from
the bearing pin in the lower turn hinge:
For appliances without
u
height
adjustment,
When a Side-by-Side appliance (S…) is fitted together with
a second appliance (as a SBS combination):
continue
with
item
Proceed according to the Side-by-Side combined fridge-
freezer installation instructions. (Accessories bag of the SBS
freezer/appliance with freezer compartment)
u
Note
For
appliances
with
u
Clean the appliance (see 6.2) .
u
height
adjustment
continue with item
.
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
Always see to good ventilation at the installation site.
u
4.3 Changing over the door hinges
You can change over the door hinges if necessary.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Putting into operation
Unscrew Fig. 6 (26)the turn hinge Fig. 6 (25).
Fully unscrew the threaded pin Fig. 6 (40) and screw it in on
the opposite side, at the turn hinge, until it is flush outside
with the turn hinge.
u
u
4.3.3 Changing the bearing parts
for appliances without height adjustment
Unscrew Fig. 6 (29)the bearing element Fig. 6 (28) transfer it
to the opposite location hole of the turn hinge and screw it
firmly into place.
u
Re-insert the stopper Fig. 6 (21) into the other hole.
Undo the screw Fig. 6 (27) and transfer it to the opposite
side.
u
u
Screw the turn hinge Fig. 6 (25) firmly into place on the new
hinge side, possibly using a cordless screwdriver (with
4 Nm).
u
Re-insert the bearing pin Fig. 6 (22) together with the
washer and adjustable-height foot*.
u
u
Tighten the threaded pin Fig. 6 (40).
4.3.5 Transferring the handle
Transfer the spring clamp
Fig. 7 (31): Depress the
latch nose and pull the
spring clamp off over it.
Slide the spring clamp
into place on the new
hinge side until it clicks
into place.
u
u
Fig. 5
Lift out the bearing pin Fig. 5 (22) together with washer
Fig. 5 (23) and adjustable-height foot* Fig. 5 (24).
Lift off the stopper Fig. 5 (21).
u
Fig. 7
u
u
u
Unscrew Fig. 5 (26) the turn hinge Fig. 5 (25).
Unscrew Fig. 5 (29) the bearing element Fig. 5 (28) , transfer
it to the opposite location hole of the turn hinge and screw it
firmly into place.
Carefully lift off the cover on the handle side Fig. 5 (27),
undo the screw Fig. 6 (40) and transfer both to the opposite
side.
u
u
Screw the turn hinge Fig. 5 (25) firmly into place on the new
hinge side, possibly using a cordless screwdriver (with
4 Nm).
Re-insert the stopper Fig. 5 (21) into the other hole.
Re-insert the bearing pin Fig. 5 (22) together with the
washer and adjustable-height foot*. In so doing, pay atten-
tion that the locating lug points backwards
u
u
4.3.4 Changing the bearing parts
For appliances with height adjustment
Fig. 8
Lift the stopper Fig. 8 (33) out of the door bearing bush and
transfer it.
u
u
Dismantle the door handle Fig. 8 (32), stoppers Fig. 8 (33)
and pressure plates* Fig. 8 (34) and transfer to the opposite
side.
When fitting the pressure plates on the opposite side, make
sure they snap properly into place.*
u
4.3.6 Fitting the door
Place the door from above onto the lower bearing pin
u
Fig. 6 (22).
Close the door.
u
u
Insert the upper turn hinge Fig. 4 (12) in the door on the new
hinge side.
Screw the upper turn hinge Fig. 4 (12)firmly into place (with
4 Nm)(2x Torx® 25) Fig. 4 (13). Possibly make preliminary
holes with a bradawl or use a cordless screwdriver.
Snap the cover Fig. 4 (10) and cover Fig. 4 (11) into place at
the opposite side.
u
u
4.3.7 Aligning the door
Fig. 6
Align the door to the appliance housing by way of the two
oblong holes in the bottom turn hinge Fig. 6 (25). To do so,
unscrew the middle screw.
u
Using the accompanying Allen key, unscrew the threaded
pin Fig. 6 (40) by about 1 turn.
u
u
u
Turn and lift out the bearing pin Fig. 6 (22) together with the
washer Fig. 6 (23) and adjustable-height foot* Fig. 6 (24).
Lift out the stopper Fig. 6 (21).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Control
4.5 Disposing of packaging
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly enough,
the door may drop out. This may lead to severe injuries. What
is more, the door may not close and therefore the appliance
may fail to cool properly.
WARNING
Danger of suffocation due to packing material and plastic film!
Do not allow children to play with packing material.
u
Screw the turn hinges firmly into place with 4 Nm.
Check all of the screws and retighten if necessary.
u
u
The packaging is made of recyclable materials:
corrugated board/cardboard
-
expanded polystyrene parts
-
polythene bags and sheets
4.4 Insertion into a row of kitchen units
-
polypropylene straps
-
nailed wooden frame with polyethylene panel*
Take the packaging material to an official collecting point.
-
u
4.6 Connecting the appliance
NOTICE
Risk of damage to the electronic control system!
Do not use stand-alone inverters (conversion of d.c. to a.c./
three-phase) or energy saving plugs.
u
WARNING
Fire and overheating hazard!
Do not use extension cables or multiple socket outlets.
u
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
Connect the appliance only with a properly installed
socket outlet with earthing contact. The socket outlet
must be fused with 10 A or higher.
It must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emer-
gency. It must be outside the area of the rear of the
appliance.
Check the electrical connection.
Plug in the power plug.
u
u
4.7 Switching on the appliance
Fig. 9
Put the appliance into operation about 2 hours before first
(1) Stack cabinet
(3) Kitchen cabinet
loading food to be frozen.
(2) Appliance
(4) Wall
Do not load food to be frozen before the temperature display
reads -18 °C.
The appliance can be inserted into a row of kitchen units. To
match the appliance Fig. 9 (2) to the height of the row of units,
a suitable stack cabinet Fig. 9 (1) can be fitted above the appli-
ance.
Press On/Off button Fig. 3 (7).
u
w
The interior light is on when the door is open.
When inserting the appliance into a row of kitchen units (max.
depth 580 mm), the appliance can be installed directly next to
the kitchen unit Fig. 9 (3). The appliance door projects relative
to the front of the kitchen unit by 34 mm at the side and by
50 mm in the middle of the appliance. It can be opened and
closed perfectly as a result.
5 Control
5.1 Brightness of the temperature
display
Important for the ventilation:
At the back of the stack cabinet there has to be a ventilation
You can adjust the brightness of the temperature display to the
-
duct of at least 50 mm depth throughout the width of the
stack cabinet.
light conditions of the room in which the appliance is installed.
The ventilation space under the ceiling has to be at least
300 cm2.
-
-
5.1.1 Adjusting the brightness
The brightness is adjustable between h0 (no illumination) and
The larger the ventilation space, the more energy-saving the
h5 (maximum luminosity).
appliance is in operation.
To activate the setting mode: press the SuperFrost button
Fig. 3 (8) for about 5 s.
u
If the appliance is installed with the hinges next to a wall
Fig. 9 (4), the distance between appliance and wall has to be at
least 40 mm. This corresponds to the projection of the handle
when the door is open.
The display indicates c.
w
w
u
The menu symbol Fig. 3 (3) shines.
Using the Up setting button Fig. 3 (1) or Down setting
button, Fig. 3 (2), select h.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Control
To confirm: briefly press the SuperFrost button Fig. 3 (8).
To make the display brighter: press Up button
Fig. 3 (1).
The audible alarm is automatically silenced, the alarm symbol
Fig. 3 (4) goes out and the temperature display stops flashing
when the temperature is sufficiently cold again.
u
u
To make the display darker: press Down button
Fig. 3 (2).
u
If the alarm status persists: (see Malfunction).
To confirm: press SuperFrost button Fig. 3 (8).
The brightness is adjusted to the new value.
To deactivate the set-up mode: press On/Off button
Fig. 3 (7).
u
w
u
5.4.1 Muting the temperature alarm
The audible alarm can be muted. When the temperature is
sufficiently cold again, the alarm function is active again.
-or-
Press alarm button Fig. 3 (9).
The audible alarm is silenced.
u
w
Wait for 5 minutes.
u
The temperature is indicated again in the temperature
display.
w
5.5 Freezing food
The rating plate indicates the maximum quantity of fresh food
you can freeze within 24 hours (see Appliance at a glance)
under "Freezing capacity ... kg/24h".
5.2 Child proofing
The child-proofing function enables you to make sure that the
The maximum load of frozen food for the drawers is 25 kg each
appliance is not inadvertently switched off by playing children.
and for the shelves 35 kg each.
5.2.1 Setting the child lock function
To activate the setting mode: press SuperFrost button
u
CAUTION
Fig. 3 (8) for about 5 s.
Risk of injury due to broken glass!
The display indicates c.
w
w
u
Bottles and cans containing drinks may burst when being
frozen. This applies particularly to sparkling drinks.
The menu symbol Fig. 3 (3) shines.
Briefly press the SuperFrost button Fig. 3 (8).to confirm.
When c1 is indicated in the display:
Do not freeze bottles and cans containing drinks!
u
Tto activate the child lock, briefly press the
SuperFrost button Fig. 3 (8).
u
In order that the food is rapidly frozen through to the core, do
not exceed the following quantities per pack:
-
Fruit, vegetables up to 1 kg
The child lock symbol Fig. 3 (11) shines. c flashes in the
w
-
Meat up to 2.5 kg
display.
Pack the food in portions in freezer bags, reusable plastic,
metal or aluminium containers.
u
When c0 is indicated in the display:
to deactivate the child lock, briefly press the SuperFrost
button Fig. 3 (8).
u
w
u
5.6 Thawing food
The child lock symbol Fig. 3 (11) goes out. c flashes in the
display.
-
at room temperature
To deactivate the set-up mode: press On/Off button
Fig. 3 (7) .
-
in a microwave oven
-
in a conventional or fan oven
-or-
Food once thawed should be re-frozen only in exceptional
cases.
u
Wait for 5 minutes.
u
The temperature is indicated again in the temperature
display.
w
5.7 Setting the temperature
The appliance is pre-set for normal operation.
5.3 Door alarm
If the door is open longer then 60 s, the audible alarm sounds.
The temperature can be set between -14 °C and -28 °C, the
recommended temperature is -18 °C.
To set the temperature higher: press Up button Fig. 3 (1).
To set the temperature lower: press Down button Fig. 3 (2).
When the button is pressed the first time, the previous value
is indicated in the temperature display.
u
u
w
The audible alarm is automatically silenced when the door is
closed.
5.3.1 Muting the door alarm
To change the temperature in 1 °C steps: briefly press the
button.
u
The audible alarm can be muted when the door is open. The
sound switch-off function is active as long as the door is left
open.
-or-
To change the temperature continuously: hold down the
u
Press alarm button Fig. 3 (9).
The door alarm is silenced.
u
w
button.
The value is displayed flashing during the setting operation.
The actual temperature is displayed about 5 s after the last
press of a button. The temperature slowly adjusts to the new
value.
w
w
5.4 Temperature alarm
The audible alarm sounds if the freezer temperature is not cold
enough.
5.8 SuperFrost
With this function you can freeze fresh food quickly through to
the core. The appliance operates with maximum refrigeration.
The noise of the refrigeration unit may be temporarily louder as
a result.
The temperature display and the alarm symbol Fig. 3 (4) flash
at the same time.
The cause of the temperature being too high may be:
warm fresh food was placed inside
-
-
too much warm ambient air flowed in when rearranging and
The maximum amount of fresh food which can be frozen in 24
removing food
h is indicated on the type plate under "freezing capacity ... kg/
power failure for some time
-
-
the appliance is faulty
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Control
24h". This amount varies according to the model and climate
rating.
You have to activate SuperFrost in good time, depending on
how much fresh food is to be frozen: about 6 hours before
placing the food inside in case of small amounts and about 24
hours in advance in case of the maximum amount of food to be
frozen.
5.11 VarioSpace
Apart from being able to remove the
drawers, you can also remove the
shelves, creating space for large
items of frozen food. Poultry, meat,
large pieces of game and high
bakery products can be frozen in
one piece and prepared.
You do not have to activate SuperFrost in the following cases:
when placing frozen food in the freezer
when freezing up to approx. 2 kg fresh food daily
-
-
The maximum load of frozen food
for the drawers is 25 kg each and
for the shelves 35 kg each.
u
5.8.1 Freezing with SuperFrost
Briefly press the SuperFrost button Fig. 3 (8) once.
The SuperFrost symbol Fig. 3 (5) shines.
The freezer temperature drops, the appliance operates with
maximum refrigerating performance.
For a small amount of food:
u
w
w
5.12 Information system
wait about 6 h.
u
u
For maximum freezing performance, put the food in the
deep, lower drawers.
For the maximum amount of food:
wait about 24 h.
u
u
Placed wrapped food straight on the lower shelves and,
once frozen, put it into the drawers.
SuperFrost is automatically deactivated. Depending on the
quantity placed inside, after 30 h at the earliest, 65 h at the
latest.
Fig. 10
w
(1) Ready-made meals, ice
cream
(4) Sausages, bread
(2) Pork, fish
(5) Game, mushrooms
Freezing is concluded.
w
w
w
(3) Fruit, vegetables
(6) Poultry, beef/veal
The SuperFrost symbol Fig. 3 (5) goes out.
The appliance continues to operate in the energy-saving,
normal mode.
The figures indicate the storage time in months for several
types of frozen food in each case. Storage times given are
guide times.
5.9 Drawers
Note
5.13 Drawer for herbs and berries
In the drawer for herbs and berries you can freeze, berries,
herbs, vegetables and other small items of food without them
sticking together. Items being frozen will largely retain their
shape, and it will be easier to remove exactly the right quantity
later on.
The energy consumption increases and the cooling perform-
ance decreases if there is insufficient ventilation.
For appliances with NoFrost:
Leave the bottom drawer in the appliance!
u
u
Always keep the air slits of the fan free at the rear wall!
5.13.1 Using the special drawer for herbs and
berries
Spread the items out loosely
in the special drawer for herbs
and berries.
u
Allow the food to freeze
through for 10 to 12 h.
u
u
Transfer the frozen food to
freezer bags or containers.
To store frozen food directly on the shelves: pull the drawer
forwards and lift it out.
u
Store freezer bags or containers in a drawer.
To thaw the items, spead them out loosely again.
u
u
5.10 Shelves
To remove the shelf: lift up at the front
u
5.14 Cold storage accumulators
and pull out.
The cold storage accumulators prevent the temperature from
To put the shelf back: simply push in as
far as it will go.
u
rising too fast in the event of power failure.
5.14.1 Using cold storage accumulators
Place the cold storage accu-
mulators in the special drawer
for herbs and berries to save
space.
u
Place the frozen cold storage
accumulators on the frozen
food in the upper front area of
the freezer compartment.
u
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Clean items of equipment by hand with lukewarm water and
a little washing-up liquid.
u
6 Maintenance
After cleaning:
Wipe dry the appliance and items of equipment.
6.1 Defrosting with NoFrost
The NoFrost system automatically defrosts the appliance.
u
u
u
Connect the appliance and switch it on again.
Switch on SuperFrost (see 5.8) .
When the temperature is sufficiently cold:
Put the food back inside.
The moisture condenses on the evaporator, is periodically
u
defrosted and evaporates.
The appliance does not have to be manually defrosted.
u
6.3 Customer service
First check whether you can correct the fault yourself by refer-
ence to the list (see Malfunction). If this is not the case, please
contact the customer service whose address is given in the
enclosed customer service list.
6.2 Cleaning the appliance
Before cleaning:
CAUTION
Risk of injury and damage as a result of hot steam!
Hot steam may damage the surfaces and cause burns.
WARNING
Risk of injury if repair work is not carried out professionally!
Do not use any steam cleaners!
u
Have any repairs and action - not expressly specified - on
the appliance and mains cable carried out by service
personnel only. (see Maintenance)
u
NOTICE
Incorrect cleaning damages the appliance!
Do not use cleaning agents in concentrated form.
Do not use any scouring or abrasive sponges or steel wool.
Do not use any cleaning agents containing sand, chloride,
chemicals or acid.
u
u
u
Read the appliance
designation
u
Fig. 11 (1), service
No. Fig. 11 (2) and
serial No. Fig. 11 (3)
off the type plate
located inside the
appliance on the left-
hand side.
Do not use chemical solvents.
u
u
Do not damage or remove the type plate on the inside of the
appliance. It is important for the customer service.
Do not pull off, bend or damage cables or other compo-
nents.
u
u
Do not allow any cleaning water to enter the drain channel,
ventilation grille or electrical parts.
Fig. 11
Notify the customer service, specifying the fault, appliance
designation Fig. 11 (1), service No. Fig. 11 (2) and serial No.
Fig. 11 (3).
Empty the appliance.
Pull out the plug.
u
u
u
-
Use soft cleaning cloths and a multi-purpose
cleaning agent with neutral pH value.
This will help us to provide you with a faster and more accu-
rate service.
w
u
-
Only use food compatible cleaning and care
agents on the inside of the appliance.
Keep the appliance closed until the customer service
arrives.
Regularly clean ventilation grilles.
u
w
Dust deposits increase energy consumption.
The food will stay cool longer.
w
u
Outside surfaces and interior:
Pull out the mains plug (not by pulling the connecting cable)
or switch off the fuse.
Cleaning inner and outer plastic surfaces:
Clean surfaces by hand with lukewarm water and a little
washing-up liquid.
u
7 Malfunction
NOTICE
Your appliance is designed and manufactured for a long life
span and reliable operation. If a malfunction nonetheless
occurs during operation, check whether it is due to a handling
error. In this case you will have to be charged for the costs
incurred, even during the warranty period. You may be able to
rectify the following faults yourself:
The stainless steel doors are provided with a high-quality
surface coating and must not be treated using the accompa-
nying care product.
Otherwise the surface coating will be affected.
Wipe the coated door surfaces using a soft, clean cloth
only. In case of stubborn dirt, use a little water or a neutral
cleaning agent. A microfibre cloth can be optionally used.
If the stainless steel side walls are dirty, clean them using
a commercially available stainless steel cleaning agent.
Then evenly apply the accompanying stainless steel care
product, making strokes in the direction of the grain.
Wipe side walls with a paint finish using a soft, clean
cloth only. In case of stubborn dirt, use a little water or a
neutral cleaning agent. A microfibre cloth can be optionally
used.
u
Appliance does not work.
The appliance is not switched on.
Switch on the appliance.
→
u
→
u
→
u
u
The power plug is not properly inserted in the wall socket.
Check power plug.
The fuse of the wall socket is not in order.
Check fuse.
u
The compressor runs for a long time.
The compressor switches to a low speed when little cold is
needed. Although the running time is increased as a result,
energy is saved.
→
Do not apply stainless steel cleaning agent to glass or plastic
surfaces to prevent them from being scratched. Darker areas at
the beginning and quite an intensive colour of the stainless
steel surface are normal.
This is normal in energy-saving models.
u
→
u
SuperFrost is activated.
The compressor runs for longer in order to rapidly cool the
food. This is normal.
Items of equipment:
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Decommissioning
The inverter regularly flashes every 15 seconds*.
The appliance is too close to a heat source.
→
The inverter is equipped with a diagnostic LED.
The flashing is normal.
→
Solution: (see Putting into operation).
u
u
The interior light is not on.
Excessive noise.
The appliance is not switched on.
Switch on the appliance.
→
u
→
u
Speed-controlled* compressors may produce varying
running noise due to different speed steps.
The sound is normal.
→
The door was open longer than 15 min.
u
The interior light automatically switches off if the door has
A bubbling and gurgling noise.
been open for about 15 min.
This noise comes from the refrigerant flowing in the refriger-
→
The LED lighting is defective or the cover is damaged:
→
ation circuit.
The sound is normal.
u
A quiet clicking noise.
WARNING
The noise is produced whenever the refrigeration unit
(motor) automatically switches on or off.
The sound is normal.
→
Risk of injury due to electric shock!
Live parts are located under the cover.
u
Have the LED interior light changed or repaired only by the
customer service or by specialized personnel trained for the
purpose.
u
A hum. It is briefly a little louder when the refrigeration
unit (the motor) switches on.
The refrigeration increases automatically when the Super-
Frost, function is activated, fresh food has just been placed
in the appliance or the door has been left open for a while.
The sound is normal.
The ambient temperature is too high.
→
WARNING
u
→
u
Danger of injury due to laser radiation, class 1M.
Do not look inside when the cover is open.
u
Vibratory noise.
The appliance is not standing firmly on the floor. As a result,
adjoining units or objects are set into vibration by the
running refrigeration unit.
→
8 Decommissioning
8.1 Switching off the appliance
Move the appliance away a little and align it using the
u
adjustable feet.
Press On/Off button Fig. 3 (7) for about 2 s.
u
w
The temperature display indicates: F0 to F9
The temperature display is dark.
There is a fault.
Contact the customer service. (see Maintenance).
→
u
8.2 Taking the appliance out of service
The temperature display indicates power failure
. The
Empty the appliance.
u
u
u
warmest temperature reached during the power failure
appears in the temperature display.
Pull out the power plug.
Clean the appliance (see 6.2) .
The freezer temperature rose too high over the last hours or
days due to a power failure or power interruption. When the
power interruption is over, the appliance will continue to
operate in the last temperature setting.
→
Leave the door open to prevent odour.
u
To cancel the display of the warmest temperature: press
alarm button Fig. 3 (9).
u
u
9 Disposing of the appliance
Check the quality of the food. Do not consume spoiled food.
Do not re-freeze thawed food.
The appliance contains some reusable materials
and should be disposed of properly - not simply
with unsorted household refuse. Appliances which
are no longer needed must be disposed of in a
professional and appropriate way, in accordance
with the current local regulations and laws.
DEMO shines in the temperature display.
The demo mode is activated.
Contact the customer service. (see Maintenance).
→
u
The outside surfaces of the appliance are warm.
The heat of the refrigeration circuit is used to prevent
condensate from forming.
→
When disposing of the appliance, ensure that the refrigeration
circuit is not damaged to prevent uncontrolled escape of the
refrigerant it contains (data on type plate) and oil.
This is normal.
u
The temperature is not cold enough.
Disable the appliance.
Pull out the plug.
u
u
u
The door of the appliance is not properly closed.
Close the door of the appliance.
Insufficient ventilation.
→
u
→
u
→
u
→
u
Cut through the connecting cable.
Clear ventilation grilles.
The ambient temperature is too high.
The appliance was opened too frequently or for too long.
Wait until the appliance reaches the required temperature
itself. If not, contact the customer service. (see Mainte-
nance).
Too much fresh food was placed inside without SuperFrost.
→
u
→
u
The temperature is incorrectly set.
Set to a colder temperature and check after 24 h.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Disposing of the appliance
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|