LevelOne
WBR-3408
11g Wireless Broadband Router, QoS
User Manual
V1.0.0-0610
Download from Www.Somanuals.com. All Manuals Search And Download.
Upgrade Firmware.......................................................................................................... 94
APPENDIX A TROUBLESHOOTING................................................................................. 95
General Problems............................................................................................................ 95
Wireless Access................................................................................................................ 96
APPENDIX B ABOUT WIRELESS LANS ......................................................................... 98
WPA-PSK ........................................................................................................................99
APPENDIX C SPECIFICATIONS...................................................................................... 102
Multi-Function Wireless Broadband router............................................................... 102
Regulatory Approvals................................................................................................... 103
.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Chapter 1
Introduction
1
This Chapter provides an overview of the Wireless Broadband router's
features and capabilities.
Congratulations on the purchase of LevelOne Wireless Broadband router. The Wire-
less Broadband router is a multi-function device providing the following services:
•
•
•
Shared Broadband Internet Access for all LAN users.
4-Port Switching Hub for 10BaseT or 100BaseT connections.
Wireless Access Point for 802.11b and 802.11g Wireless Stations.
Figure 1: Wireless Broadband router
Wireless Broadband router Features
The Wireless Broadband router incorporates many advanced features, carefully
designed to provide sophisticated functions while being easy to use.
Internet Access Features
•
•
•
Shared Internet Access. All users on the LAN or WLAN can access the
Internet through this Wireless Broadband router, using only a single external IP
Address. The local (invalid) IP Addresses are hidden from external sources. This
process is called NAT (Network Address Translation).
DSL & Cable Modem Support. The Wireless Broadband router has a
10/100BaseT Ethernet port for connecting a DSL or Cable Modem. All popular
DSL and Cable Modems are supported. SingTel RAS and Big Pond (Australia)
login support is also included.
PPPoE, PPTP, SingTel RAS and Telstra Big Pond Support. The Internet
(WAN port) connection supports PPPoE (PPP over Ethernet), PPTP (Peer-to-
Peer Tunneling Protocol), SingTel RAS and Telstra Big Pond (Australia), as well
as "Direct Connection" type services. Unnumbered IP with PPPoE is also sup-
ported.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
•
Fixed or Dynamic IP Address. On the Internet (WAN port) connection, the
Wireless Broadband router supports both Dynamic IP Address (IP Address is al-
located on connection) and Fixed IP Address.
Advanced Internet Functions
•
Communication Applications. Support for Internet communication applica-
tions, such as interactive Games, Telephony, and Conferencing applications,
which are often difficult to use when behind a Firewall, is included.
•
Special Internet Applications. Applications which use non-standard connec-
tions or port numbers are normally blocked by the Firewall. The ability to define
and allow such applications is provided, to enable such applications to be used
normally.
•
•
Virtual Servers. This feature allows Internet users to access Internet servers
on your LAN. The required setup is quick and easy.
DDNS Support. DDNS (Dynamic DNS) allows Internet users to connect to
Virtual Servers on your LAN using a domain name, even if your IP address is not
fixed.
•
Multi-DMZ. For each WAN (Internet) IP address allocated to you, one (1) PC on
your local LAN can be configured to allow unrestricted 2-way communication with
Servers or individual users on the Internet. This provides the ability to run pro-
grams which are incompatible with Firewalls.
•
URL Filter. Use the URL Filter to block access to undesirable Web sites by LAN
users.
•
•
Internet Access Log. See which Internet connections have been made.
Access Control. Using the Access Control feature, you can assign LAN users
to different groups, and determine which Internet services are available to each
group.
•
VPN Pass through Support. PCs with VPN (Virtual Private Networking)
software using PPTP, L2TP and IPSec are transparently supported - no configura-
tion is required.
Wireless Features
•
Standards Compliant. The Wireless Broadband router complies with the
IEEE802.11g (DSSS) specifications for Wireless LANs.
•
Supports both 802.11b and 802.11g Wireless Stations. The 802.11g
standard provides for backward compatibility with the 802.11b standard, so both
802.11b and 802.11g Wireless stations can be used simultaneously.
•
•
•
•
•
Speeds to 54Mbps. All speeds up to the 802.11g maximum of 54Mbps are
supported.
WEP support. Support for WEP (Wired Equivalent Privacy) is included. Key
sizes of 64 Bit and 128 Bit are supported.
WPA-PSK support. Support for WPA-PSK is included. WPA-PSK is more
secure than WEP, and should be used if possible.
WPA2-PSK support. Support for WPA2-PSK is also included. WPA2-PSK
uses the extremely secure AES encryption method.
Wireless MAC Access Control. The Wireless Access Control feature can
check the MAC address (hardware address) of Wireless stations to ensure that
only trusted Wireless Stations can access your LAN.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
•
Simple Configuration. If the default settings are unsuitable, they can be
changed quickly and easily.
LAN Features
•
4-Port Switching Hub. The Wireless Broadband router incorporates a 4-port
10/100BaseT switching hub, making it easy to create or extend your LAN.
•
DHCP Server Support. Dynamic Host Configuration Protocol provides a
dynamic IP address to PCs and other devices upon request. The Wireless Broad-
band router can act as a DHCP Server for devices on your local LAN and WLAN.
•
Multi Segment LAN Support. LANs containing one or more segments are
supported; via the Wireless Broadband router's RIP (Routing Information Protocol)
support and built-in static routing table.
Configuration & Management
•
Easy Setup. Use your WEB browser from anywhere on the LAN or WLAN for
configuration.
•
Configuration File Upload/Download. Save (download) the configuration
data from the Wireless Broadband router to your PC, and restore (upload) a pre-
viously-saved configuration file to the Wireless Broadband router.
•
Remote Management. The Wireless Broadband router can be managed from
any PC on your LAN. And, if the Internet connection exists, it can also (optionally)
be configured via the Internet.
•
•
Network Diagnostics. You can use the Wireless Broadband router to perform
a Ping or DNS lookup.
UPnP Support. UPnP (Universal Plug and Play) allows automatic discovery
and configuration of the Wireless Broadband router. UPnP is by supported by
Windows ME, XP, or later.
Security Features
•
•
•
Password - protected Configuration. Optional password protection is
provided to prevent unauthorized users from modifying the configuration data and
settings.
Wireless LAN Security. WEP (Wired Equivalent Privacy) is supported, as well
as Wireless access control to prevent unknown wireless stations from accessing
your LAN.
NAT Protection. An intrinsic side effect of NAT (Network Address Translation)
technology is that by allowing all LAN users to share a single IP address, the loca-
tion and even the existence of each PC is hidden. From the external viewpoint,
there is no network, only a single device - the Wireless Broadband router.
•
•
Stated Inspection Firewall. All incoming data packets are monitored and all
incoming server requests are filtered, thus protecting your network from malicious
attacks from external sources.
Protection against DoS attacks. DoS (Denial of Service) attacks can flood
your Internet connection with invalid packets and connection requests, using so
much bandwidth and so many resources that Internet access becomes unavail-
able. The Wireless Broadband router incorporates protection against DoS attacks.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Package Contents
The following items should be included:
•
•
•
•
•
WBR-3408
Power Adapter
Dipole Antenna
Quick Installation Guide
CD Manual
If any of the above items are damaged or missing, please contact your dealer imme-
diately.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Physical Details
Front-mounted LEDs
Figure 2: Front Panel
On - Power on.
Off - No power.
Power LED
WLAN LED
On - Wireless connection available; Wireless Access Point is ready
for use.
Off - No Wireless connection available.
Flashing - Data is being transmitted or received via the Wireless
access point. Data includes "network traffic" as well as user data.
Internet LED On - Internet connection is available.
Off - No Internet connection available.
Flashing - Data is being transmitted or received.
WAN LED
On - Connection to the Broadband Modem attached to the WAN
(Internet) port is established.
Off - No connection to the Broadband Modem.
Flashing - Data is being transmitted or received via the WAN port.
On - Corresponding LAN (hub) port is active.
LAN (1~4)
LEDs
Off - No active connection on the corresponding LAN (hub) port.
Flashing - Data is being transmitted or received via the corre-
sponding LAN (hub) port.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Rear Panel
Figure 3: Rear Panel
2dBi detachable antenna.
Antenna
WAN
Connect the DSL or Cable Modem here. If your modem came
with a cable, use the supplied cable. Otherwise, use a stan-
dard LAN cable.
Use standard LAN cables (RJ45 connectors) to connect your
PCs to these ports.
LAN
If required, any port can be connected to another hub. Any
LAN port will automatically function as an "Uplink" port when
necessary.
This button has two (2) functions:
Reset Button
•
Reboot. When pressed and released, the Wireless
Broadband router will reboot (restart).
•
Clear All Data. This button can also be used to clear ALL
data and restore ALL settings to the factory default values.
To Clear All Data and restore the factory default values:
1. Power Off.
2. Hold the Reset Button down while you Power On.
3. Keep holding the Reset Button for a few seconds, until the
RED LED has flashed TWICE.
4. Release the Reset Button. The Wireless Broadband router
is now using the factory default values.
Connect the supplied power adapter here.
Power port
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Installation
2
This Chapter covers the physical installation of the Wireless Broad-
band router.
Requirements
•
Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45
connectors.
•
•
TCP/IP protocol must be installed on all PCs.
For Internet Access, an Internet Access account with an ISP, and either of a DSL
or Cable modem (for WAN port usage)
•
To use the Wireless Access Point, all Wireless devices must be compliant with the
IEEE802.11b or IEEE802.11g specifications.
Procedure
Figure 4: Installation Diagram
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
1. Choose an Installation Site
Select a suitable place on the network to install the Wireless Broadband router.
Ensure the Wireless Broadband router and the DSL/Cable modem are powered
OFF.
For best Wireless reception and performance, the Wireless
Broadband router should be positioned in a central location
with minimum obstructions between the Wireless Broad-
band router and the PCs.
Also, if using multiple Access Points, adjacent Access
Points should use different Channels.
2. Connect LAN Cables
Use standard LAN cables to connect PCs to the Switching Hub ports on the Wire-
less Broadband router. Both 10BaseT and 100BaseT connections can be used
simultaneously.
If required, connect any port to a normal port on another Hub, using a standard
LAN cable. Any LAN port on the Wireless Broadband router will automatically
function as an "Uplink" port when required.
3. Connect WAN Cable
Connect the DSL or Cable modem to the WAN port on the Wireless Broadband
router. Use the cable supplied with your DSL/Cable modem. If no cable was sup-
plied, use a standard cable.
4. Power Up
•
•
Power on the Cable or DSL modem.
Connect the supplied power adapter to the Wireless Broadband router and power
up.
Use only the power adapter provided. Using a different one may cause hardware
damage
5. Check the LEDs
•
•
The Power LED should be ON.
For each LAN (PC) connection, the LAN Link/Act LED should be ON (provided the
PC is also ON.)
•
•
The WAN LED should be ON.
The WLAN LED should be ON
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Setup
3
This Chapter provides Setup details of the Wireless Broadband router.
Overview
This chapter describes the setup procedure for:
•
•
•
•
Internet Access
LAN configuration
Wireless setup
Assigning a Password to protect the configuration data.
PCs on your local LAN may also require configuration. For details, see Chapter 4 - PC
Configuration.
Other configuration may also be required, depending on which features and functions
of the Wireless Broadband router you wish to use. Use the table below to locate
detailed instructions for the required functions.
To Do this:
Refer to:
Configure PCs on your LAN.
Chapter 4:
PC Configuration
Check Wireless Broadband router operation and
Status.
Chapter 5:
Operation and Status
Use any of the following Advanced features:
Chapter 6:
Advanced Features
•
•
•
•
•
Access Control
Dynamic DNS
Internet (Special Applications, DMZ)
Virtual Servers (Port Forwarding)
WAN Port
Use any of the following Administration Configuration Chapter 7
settings or features: Advanced Administration
•
•
•
•
•
•
•
•
•
•
Config File download/upload
Logs
Network Diagnostics (Ping, DNS Lookup)
Options (Backup DNS, UPnP)
PC Database
QoS
Remote Management
Routing (RIP and static Routing)
Security settings
Upgrade Firmware
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Configuration Program
The Wireless Broadband router contains an HTTP server. This enables you to con-
nect to it, and configure it, using your Web Browser. Your Browser must support
JavaScript.
The configuration program has been tested on the following browsers:
•
•
Netscape V4.08 or later
Internet Explorer V4 or later
Preparation
Before attempting to configure the Wireless Broadband router, please ensure that:
•
Your PC can establish a physical connection to the Wireless Broadband router.
The PC and the Wireless Broadband router must be directly connected (using the
Hub ports on the Wireless Broadband router) or on the same LAN segment.
•
•
The Wireless Broadband router must be installed and powered ON.
If the Wireless Broadband router's default IP Address (192.168.0.1) is already
used by another device, the other device must be turned OFF until the Wireless
Broadband router is allocated a new IP Address during configuration.
Using UPnP
If your Windows system supports UPnP, an icon for the Wireless Broadband router
will appear in the system tray, notifying you that a new network device has been found,
and offering to create a new desktop shortcut to the newly-discovered device.
•
•
•
Unless you intend to change the IP Address of the Wireless Broadband router,
you can accept the desktop shortcut.
Whether you accept the desktop shortcut or not, you can always find UPnP de-
vices in My Network Places (previously called Network Neighborhood).
Double - click the icon for the Wireless Broadband router (either on the Desktop,
or in My Network Places) to start the configuration. Refer to the following section
Setup Wizard for details of the initial configuration process.
Using your Web Browser
To establish a connection from your PC to the Wireless Broadband router:
1. After installing the Wireless Broadband router in your LAN, start your PC. If your
PC is already running, restart it.
2. Start your WEB browser.
3. In the Address box, enter "HTTP://" and the IP Address of the Wireless Broad-
band router, as in this example, which uses the Wireless Broadband router's
default IP Address:
HTTP://192.168.0.1
Because the default password is blank, your will not be prompted for a password.
However, you should assign a password. See the Password section later in this
chapter for details.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
If you can't connect
If the Wireless Broadband router does not respond, check the following:
•
The Wireless Broadband router is properly installed, LAN connection is
OK, and it is powered ON. You can test the connection by using the
"Ping" command:
•
•
Open the MS-DOS window or command prompt window.
Enter the command:
ping 192.168.0.1
If no response is received, either the connection is not working, or
your PC's IP address is not compatible with the Wireless Broad-
band router's IP Address. (See next item.)
•
If your PC is using a fixed IP Address, its IP Address must be within the
range 192.168.0.2 to 192.168.0.254 to be compatible with the Wireless
Broadband router's default IP Address of 192.168.0.1. Also, the Net-
work Mask must be set to 255.255.255.0. See Chapter 4 - PC
Configuration for details on checking your PC's TCP/IP settings.
•
•
Ensure that your PC and the Wireless Broadband router are on the
same network segment. (If you don't have a broadband router, this
must be the case.)
Ensure you are using the wired LAN interface. The Wireless interface
can only be used if its configuration matches your PC's wireless set-
tings.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Setup Wizard
The first time you connect to the Wireless Broadband router, the Setup Wizard will run
automatically. (The Setup Wizard will also run if the Wireless Broadband router's
default settings are restored.)
1. Step through the Wizard until finished.
•
You need to know the type of Internet connection service used by your ISP.
Check the data supplied by your ISP.
•
The common connection types are explained in the tables below.
2. On the final screen of the Wizard, run the test and check that an Internet connec-
tion can be established.
3. If the connection test fails:
•
•
•
Check your data, the Cable/DSL modem, and all connections.
Check that you have entered all data correctly.
If using a Cable modem, your ISP may have recorded the MAC (physical) ad-
dress of your PC. Run the Wizard, and on the Cable Modem screen, use the
"Clone MAC address" button to copy the MAC address from your PC to the
Wireless Broadband router.
Common Connection Types
Cable Modems
Type
Details
ISP Data required
Dynamic
IP Address
Your IP Address is allo-
cated automatically, when
you connect to you ISP.
Usually, none.
However, some ISP's may
require you to use a particu-
lar Hostname, Domain name,
or MAC (physical) address.
Static (Fixed) Your ISP allocates a per-
IP Address allocated to you.
IP Address
manent IP Address to you.
Some ISP's may also require
you to use a particular Host-
name, Domain name, or
MAC (physical) address.
DSL Modems
Type
Details
ISP Data required
Dynamic
IP Address
Your IP Address is allo-
cated automatically, when
you connect to you ISP.
None.
Static (Fixed) Your ISP allocates a per-
IP Address allocated to you.
IP Address
manent IP Address to you.
PPPoE
You connect to the ISP only User name and password.
when required. The IP
address is usually allocated
automatically.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
PPTP
PPTP is mainly used in
Europe.
•
•
Server IP Address.
User name and pass-
word.
You connect to the ISP only
when required. The IP
address is usually allocated
automatically, but may be
Static (Fixed).
•
IP Address allocated to
you, if Static (Fixed).
Other Modems (e.g. Broadband Wireless)
Type
Details
ISP Data required
Dynamic
IP Address
Your IP Address is allocated
automatically, when you
connect to you ISP.
None.
Static (Fixed) Your ISP allocates a perma-
IP Address allocated to
you.
IP Address
nent IP Address to you.
Big Pond (Australia)
For this connection method, the following data is required:
•
•
•
User Name
Password
Big Pond Server IP address
SingTel RAS
For this connection method, the following data is required:
•
•
•
User Name
Password
RAS Plan
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Home Screen
After finishing the Setup Wizard, you will see the Home screen. When you connect in
future, you will see this screen when you connect. An example screen is shown below.
Figure 5: Home Screen
Navigation & Data Input
•
Use the menu bar on the left of the screen, and the "Back" button on your Browser,
for navigation.
•
Changing to another screen without clicking "Save" does NOT save any changes
you may have made. You must "Save" before changing screens or your data will
be ignored.
On each screen, clicking the "Help" button will
display help for that screen.
From any help screen, you can access the list of all
help files (help index).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
LAN Screen
Use the LAN link on the main menu to reach the LAN screen. An example screen is
shown below.
Figure 6: LAN Screen
Data - LAN Screen
TCP/IP
IP address for the Wireless Broadband router, as seen from the
local LAN. Use the default value unless the address is already in
use or your LAN is using a different IP address range. In the
latter case, enter an unused IP Address from within the range
used by your LAN.
IP Address
The default value 255.255.255.0 is standard for small (class "C")
networks. For other networks, use the Network Mask for the
LAN segment to which the Wireless Broadband router is at-
tached. i.e. the same value as the PCs on that LAN segment.
Subnet Mask
DHCP Server
•
If Enabled, the Wireless Broadband router will allocate IP
Addresses to PCs (DHCP clients) on your LAN when they
start up. The default (and recommended) value is Enabled.
•
If you are already using a DHCP Server, this setting must be
Disabled, and the existing DHCP server must be re-
configured to treat the Wireless Broadband router as the de-
fault Gateway. See the following section for further details.
•
•
The Start IP Address and Finish IP Address fields set the
values used by the DHCP server when allocating IP Ad-
dresses to DHCP clients. This range also determines the
number of DHCP clients supported.
Enter the desired values for DNS IP Address, Gateway IP
Address and Leased Time, if preferred.
See the following section for further details on using DHCP.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Buttons
Save any changes you have made. Note that if you change the
Save
Wireless Broadband router's IP address, your connection will be
lost. You will have to re-connect using the new IP address.
The "Cancel" button will discard any data you have entered and
reload the file from the Wireless Broadband router.
Cancel
DHCP
What DHCP Does
A DHCP (Dynamic Host Configuration Protocol) Server allocates a valid IP address to
a DHCP Client (PC or device) upon request.
•
•
The client request is made when the client device starts up (boots).
The DHCP Server provides the Gateway and DNS addresses to the client, as well
as allocating an IP Address.
•
•
The Wireless Broadband router can act as a DHCP server.
Windows 98/ME and other non-Server versions of Windows will act as a DHCP
client. This is the default Windows setting for the TCP/IP network protocol. How-
ever, Windows uses the term Obtain an IP Address automatically instead of
"DHCP Client".
•
You must NOT have two (2) or more DHCP Servers on the same LAN segment.
(If your LAN does not have other Broadband routers, this means there must only
be one (1) DHCP Server on your LAN.)
Using the Wireless Broadband router's DHCP Server
This is the default setting. The DHCP Server settings are on the LAN screen. On this
screen, you can:
•
•
Enable or Disable the Wireless Broadband router's DHCP Server function.
Set the range of IP Addresses allocated to PCs by the DHCP Server function.
You can assign Fixed IP Addresses to some devices
while using DHCP, provided that the Fixed IP Addresses
are NOT within the range used by the DHCP Server.
Using another DHCP Server
You can only use one (1) DHCP Server per LAN segment. If you wish to use another
DHCP Server, rather than the Wireless Broadband router's, the following procedure is
required.
1. Disable the DHCP Server feature in the Wireless Broadband router. This setting is
on the LAN screen.
2. Configure the DHCP Server to provide the Wireless Broadband router's IP Ad-
dress as the Default Gateway.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
To Configure your PCs to use DHCP
This is the default setting for TCP/IP under Windows 98/ME.
See Chapter 4 - Client Configuration for the procedure to check these settings.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Wireless Screen
The Wireless Broadband router's settings must match the other Wireless stations.
Note that the Wireless Broadband router will automatically accept both 802.11b and
802.11g connections, and no configuration is required for this feature.
To change the Wireless Broadband router's default settings for the Wireless Access
Point feature, use the Wireless link on the main menu to reach the Wireless screen.
An example screen is shown below.
Figure 7: Wireless Screen
Data - Wireless Screen
Identification
On your PC, some Wireless status screens may display this
name as the Access Point in use.
Station name
Select your region from the drop-down list. This field displays the
region of operation for which the wireless interface is intended. It
may not be legal to operate the broadband router in a region
other than the region shown here. If your country or region is not
listed, please check with your local government agency for more
information on which channels you are allowed to use, and
select a region which allows those channels. (The channel list
changes according to the selected region.)
Region
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
•
•
If using an ESS (Extended Service Set, with multiple access
points) this ID is called an ESSID (Extended Service Set
Identifier).
SSID
To communicate, all Wireless stations should use the same
SSID/ESSID.
Options
Mode
Select the desired mode:
•
•
•
g & b - Both 802.11.g and 802.11b Wireless stations will be
able to use the Wireless Broadband router.
g only - Only 802.11g Wireless stations can use the Wire-
less Broadband router.
b only - Only 802.11b connections are available. 802.11g
Wireless Stations will only be able to use the Wireless
Broadband router if they are fully backward-compatible with
the 802.11b standard.
This field determines which operating frequency will be used. It
should not be necessary to change the wireless channel unless
you notice interference problems with another nearby access
point.
Channel No.
If Enabled, the SSID will broadcast its name to all Wireless
Stations. Stations which have no SSID (or a "null" value) can
then adopt the correct SSID for connections to this Access
Point.
Broadcast
SSID
Wireless Security
Current Setting
The current security setting is displayed.
Click this button to access the Wireless security sub-screen, and
modify the security settings as required. See the following sec-
tion for details.
Configure
Button
Access Point
•
•
•
•
•
If Enabled, wireless stations will be able to locate and use
this Access Point.
Enable Access
Point
If Disabled, the wireless interface is disabled, and will nei-
ther transmit nor receive wireless traffic.
The Wireless (WLAN) LED on the front panel will remain
OFF if the Wireless interface is disabled.
All Wireless Stations - All wireless stations can use the
access point to access your LAN.
Allow LAN
access
Selected Wireless stations only - Only selected wireless
stations access your LAN. To select the required wireless
stations, click the "Select Stations" button.
•
•
All Wireless Stations - All wireless stations can use the
access point to access the Internet.
Allow Internet
access
Selected Wireless stations only - Only selected wireless
stations use the access point to access the Internet. To se-
lect the required wireless stations, click the "Select Stations"
button.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Buttons
Click this button to view the Wireless security sub-screen.
Configure
Select Stations
Save
Click this button to select the required PCs.
Save the data on screen.
The "Cancel" button will discard any data you have entered
since the last "Save" operation.
Cancel
Wireless Security Screen
This screen is accessed by clicking the "Configure" button on the Wireless screen.
There are 3 options for Wireless security:
•
•
•
Disabled - no data encryption is used.
WEP - data is encrypted using the WEP standard.
WPA1/2-PSK - data is encrypted using the WPA standard. This is a later standard
than WEP, and provides much better security than WEP.
Wireless Security - WEP
Figure 8: WEP Screen
Data - WEP Screen
Normally this can be left at the default value of "Automatic." If
that fails, select the appropriate value - "Open System" or
"Shared Key." Check your wireless card's documentation to see
what method to use.
Authentication
Select the WEP Encryption level:
Key Size
•
64-bit (sometimes called 40-bit) encryption. You must enter
at least the default key. For 64 Bit Encryption, the key size is
10 chars in HEX (0~9 and A~F).
•
128-bit encryption. You must enter at least the default key.
For 128 Bit Encryption, the key size is 26 chars in HEX (0~9
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
and A~F).
•
•
Use the radio buttons to select the default key.
Key
Enter the key value you wish to use. Other stations must
have the same key values.
•
Keys must be entered in Hex. Hex characters are the digits
(0 ~ 9) and the letters A ~ F.
Enter a word or group of printable characters in the Passphrase
box and click the "Generate " button to automatically configure
the WEP Key(s). If encryption strength is set to 64 bit, then each
of the four key fields will be populated with key values. If encryp-
tion strength is set to 128 bit, then only the selected WEP key
field will be given a key value.
Passphrase
Wireless Security - WPA1/2-PSK
If "WPA1/2-PSK" is selected, the screen will look like the following example.
Figure 9: WPA1/2-PSK Screen
Data - WPA1/2-PSK screen
Select the desired option:
Authentication
•
WPA-PSK: Like WEP, data is encrypted before trans-
mission. WPA is more secure than WEP, and should be
used if possible.
•
•
WPA2-PSK: This is a further development of WPA-PSK,
and offers even greater security.
WPA-PSK+WPA2-PSK: This method, sometimes called
"Mixed Mode", allows clients to use EITHER WPA-PSK
OR WPA2-PSK.
Enter the Network key value. Data is encrypted using a key
derived from the network key. Other Wireless Stations must
use the same network key. The PSK must be from 8 to 63
characters in length.
PSK
This determines how often the encryption key is changed.
Enter the desired value.
Key Lifetime
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Select the desired option. Wireless Stations must use the
same method.
Encryption
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Password Screen
The password screen allows you to assign a password to the Wireless Broadband
router.
Figure 10: Password Screen
Once you have assigned a password to the Wireless Broadband router (on the Pass-
word screen above) you will be prompted for the password when you connect, as
shown below. (If no password has been set, this dialog will not appear.)
Figure 11: Password Dialog
•
•
Leave the "User Name" blank.
Enter the password for the Wireless Broadband router, as set on the Password
screen above.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
PC Configuration
4
This Chapter details the PC Configuration required on the local ("Inter-
nal") LAN.
Overview
For each PC, the following may need to be configured:
•
•
•
TCP/IP network settings
Internet Access configuration
Wireless configuration
Windows Clients
This section describes how to configure Windows clients for Internet access via the
Wireless Broadband router.
The first step is to check the PC's TCP/IP settings.
The Wireless Broadband router uses the TCP/IP network protocol for all functions, so
it is essential that the TCP/IP protocol be installed and configured on each PC.
TCP/IP Settings - Overview
If using the default Wireless Broadband router settings, and the default
Windows TCP/IP settings, no changes need to be made.
•
•
By default, the Wireless Broadband router will act as a DHCP Server, automati-
cally providing a suitable IP Address (and related information) to each PC when
the PC boots.
For all non-Server versions of Windows, the default TCP/IP setting is to act as a
DHCP client.
If using a Fixed (specified) IP address, the following changes are re-
quired:
•
•
The Gateway must be set to the IP address of the Wireless Broadband router
The DNS should be set to the address provided by your ISP.
If your LAN has a Broadband router, the LAN Administra-
tor must re-configure the Broadband router itself. Refer
to Chapter 8 - Advanced Setup for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Checking TCP/IP Settings - Windows 9x/ME:
1. Select Control Panel - Network. You should see a screen like the following:
Figure 12: Network Configuration
2. Select the TCP/IP protocol for your network card.
3. Click on the Properties button. You should then see a screen like the following.
Figure 13: IP Address (Win 9x)
Ensure your TCP/IP settings are correct, as follows:
Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the
default Windows setting. Using this is recommended. By default, the Wireless
Broadband router will act as a DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Broadband
router.
Using "Specify an IP Address"
If your PC is already configured, check with your network administrator before making
the following changes:
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
•
On the Gateway tab, enter the Wireless Broadband router's IP address in the New
Gateway field and click Add, as shown below. Your LAN administrator can advise
you of the IP Address they assigned to the Wireless Broadband router.
Figure 14: Gateway Tab (Win 98)
•
On the DNS Configuration tab, ensure Enable DNS is selected. If the DNS Server
Search Order list is empty, enter the DNS address provided by your ISP in the
fields beside the Add button, then click Add.
Figure 15: DNS Tab (Win 98)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Checking TCP/IP Settings - Windows 2000:
1. Select Control Panel - Network and Dial-up Connection.
2. Right - click the Local Area Connection icon and select Properties. You should
see a screen like the following:
Figure 16: Network Configuration (Win 2000)
3. Select the TCP/IP protocol for your network card.
4. Click on the Properties button. You should then see a screen like the following.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Figure 17: TCP/IP Properties (Win 2000)
5. Ensure your TCP/IP settings are correct, as described below.
Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the
default Windows setting. Using this is recommended. By default, the Wireless
Broadband router will act as a DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Broadband
router.
Using a fixed IP Address ("Use the following IP Address")
If your PC is already configured, check with your network administrator before making
the following changes.
•
Enter the Wireless Broadband router's IP address in the Default gateway field and
click OK. (Your LAN administrator can advise you of the IP Address they assigned
to the Wireless Broadband router.)
•
If the DNS Server fields are empty, select Use the following DNS server ad-
dresses, and enter the DNS address or addresses provided by your ISP, then
click OK.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Checking TCP/IP Settings - Windows XP
1. Select Control Panel - Network Connection.
2. Right click the Local Area Connection and choose Properties. You should see a
screen like the following:
Figure 18: Network Configuration (Windows XP)
3. Select the TCP/IP protocol for your network card.
4. Click on the Properties button. You should then see a screen like the following.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Figure 19: TCP/IP Properties (Windows XP)
5. Ensure your TCP/IP settings are correct.
Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the
default Windows setting. Using this is recommended. By default, the Wireless
Broadband router will act as a DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Broadband
router.
Using a fixed IP Address ("Use the following IP Address")
If your PC is already configured, check with your network administrator before making
the following changes.
•
In the Default gateway field, enter the Wireless Broadband router's IP address
and click OK. Your LAN administrator can advise you of the IP Address they as-
signed to the Wireless Broadband router.
•
If the DNS Server fields are empty, select Use the following DNS server ad-
dresses, and enter the DNS address or addresses provided by your ISP, then
click OK.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Internet Access
To configure your PCs to use the Wireless Broadband router for Internet access:
•
Ensure that the DSL modem, Cable modem, or other permanent connection is
functional.
•
Use the following procedure to configure your Browser to access the Internet via
the LAN, rather than by a Dial-up connection.
For Windows 9x/ME/2000
1. Select Start Menu - Settings - Control Panel - Internet Options.
2. Select the Connection tab, and click the Setup button.
3. Select "I want to set up my Internet connection manually, or I want to connect
through a local area network (LAN)" and click Next.
4. Select "I connect through a local area network (LAN)" and click Next.
5. Ensure all of the boxes on the following Local area network Internet Configuration
screen are unchecked.
6. Check the "No" option when prompted "Do you want to set up an Internet mail
account now?".
7. Click Finish to close the Internet Connection Wizard.
Setup is now completed.
For Windows XP
1. Select Start Menu - Control Panel - Network and Internet Connections.
2. Select Set up or change your Internet Connection.
3. Select the Connection tab, and click the Setup button.
4. Cancel the pop-up "Location Information" screen.
5. Click Next on the "New Connection Wizard" screen.
6. Select "Connect to the Internet" and click Next.
7. Select "Set up my connection manually" and click Next.
8. Check "Connect using a broadband connection that is always on" and click Next.
9. Click Finish to close the New Connection Wizard.
Setup is now completed.
Accessing AOL
To access AOL (America On Line) through the Wireless Broadband router, the AOL
for Windows software must be configured to use TCP/IP network access, rather than
a dial-up connection. The configuration process is as follows:
•
Start the AOL for Windows communication software. Ensure that it is Version 2.5,
3.0 or later. This procedure will not work with earlier versions.
•
•
Click the Setup button.
Select Create Location, and change the location name from "New Locality" to
"Wireless Broadband router".
•
•
•
Click Edit Location. Select TCP/IP for the Network field. (Leave the Phone Num-
ber blank.)
Click Save, then OK.
Configuration is now complete.
Before clicking "Sign On", always ensure that you are using the "Wireless Broad-
band router" location.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Macintosh Clients
From your Macintosh, you can access the Internet via the Wireless Broadband router.
The procedure is as follows.
1. Open the TCP/IP Control Panel.
2. Select Ethernet from the Connect via pop-up menu.
3. Select Using DHCP Server from the Configure pop-up menu. The DHCP Client ID
field can be left blank.
4. Close the TCP/IP panel, saving your settings.
Note:
If using manually assigned IP addresses instead of DHCP, the required changes are:
•
Set the Broadband router Address field to the Wireless Broadband router's IP
Address.
•
Ensure your DNS settings are correct.
Linux Clients
To access the Internet via the Wireless Broadband router, it is only necessary to set
the Wireless Broadband router as the "Gateway".
Ensure you are logged in as "root" before attempting any changes.
Fixed IP Address
By default, most Unix installations use a fixed IP Address. If you wish to continue
using a fixed IP Address, make the following changes to your configuration.
•
•
Set your "Default Gateway" to the IP Address of the Wireless Broadband router.
Ensure your DNS (Name server) settings are correct.
To act as a DHCP Client (recommended)
The procedure below may vary according to your version of Linux and X -windows
shell.
1. Start your X Windows client.
2. Select Control Panel - Network
3. Select the "Interface" entry for your Network card. Normally, this will be called
"eth0".
4. Click the Edit button, set the "protocol" to "DHCP", and save this data.
5. To apply your changes
•
•
Use the "Deactivate" and "Activate" buttons, if available.
OR, restart your system.
Other Unix Systems
To access the Internet via the Wireless Broadband router:
•
Ensure the "Gateway" field for your network card is set to the IP Address of the
Wireless Broadband router.
•
Ensure your DNS (Name Server) settings are correct.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Configuration
Wireless Station Configuration
This section applies to all Wireless stations wishing to use the Wireless Broadband
router's Access Point, regardless of the operating system which is used on the client.
To use the Wireless Access Point in the Wireless Broadband router, each Wireless
Station must have compatible settings, as follows:
Mode
The mode must be set to Infrastructure.
This must match the value used on the Wireless Broadband
SSID (ESSID)
router. The default value is default
Note! The SSID is case sensitive.
By default, Wireless security on the Wireless Broadband router is
disabled.
Wireless
Security
•
If Wireless security remains disabled on the Wireless Broad-
band router, all stations must have wireless security disabled.
•
If Wireless security is enabled on the Wireless Broadband
router, each station must use the same settings as the Wire-
less Broadband router.
Note:
By default, the Wireless Broadband router will allow both 802.11b and 802.11g con-
nections.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Operation and Status
5
This Chapter details the operation of the Wireless Broadband router
and the status screens.
Operation
Once both the Wireless Broadband router and the PCs are configured, opera-
tion is automatic.
However, there are some situations where additional Internet configuration may be
required:
•
If using Internet-based Communication Applications, it may be necessary to
specify which PC receives an incoming connection. Refer to Chapter 6 - Ad-
vanced Features for further details.
•
Applications which use non-standard connections or port numbers may be
blocked by the Wireless Broadband router's built-in firewall. You can define such
applications as Special Applications to allow them to function normally. Refer to
Chapter 6 - Advanced Features for further details.
•
Some non-standard applications may require use of the DMZ feature. Refer to
Chapter 6 - Advanced Features for further details.
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Status
Status Screen
Use the Status link on the main menu to view this screen.
Figure 20: Status Screen
Data - Status Screen
Internet
This indicates the current connection method, as set in the
Setup Wizard or WAN Port screen.
Connection Method
Broadband Modem
Internet Connection
This shows the status of the connection from the Wireless
Broadband router to the Broadband Modem.
Current connection status:
•
•
•
Active
Idle
Failed
If there is an error, you can click the "Connection Details"
button to find out more information.
This IP Address is allocated by the ISP (Internet Service
Provider). If there is no current connection, this will be
blank or 0.0.0.0.
Internet IP Address
Click this button to open a sub-window and view a detailed
description of the current connection. Depending on the
type of connection, a "Connection Log" may also be avail-
able.
"Connection De-
tails"
Button
LAN
The IP Address of the Wireless Broadband router.
IP Address
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
The Network Mask (Subnet Mask) for the IP Address
above.
Network Mask
DHCP Server
This shows the status of the DHCP Server function - either
"Enabled" or "Disabled".
For additional information about the PCs on your LAN, and
the IP addresses allocated to them, use the PC Database
option on the Administration menu.
System
This displays the current name of the Wireless Broadband
router.
Device Name
The current version of the firmware installed in the Wireless
Broadband router.
Firmware Version
Buttons
View the details of the current Internet connection. The sub-
screen displayed will depend on the connection method
used. See the following sections for details of each sub-
screen.
Connection Details
Display all system information in a sub-window.
System Data
Restart
Clicking this button will restart (reboot) the Wireless Broad-
band router. All existing connections though the Wireless
Broadband router will be terminated, but will usually re-
connect automatically.
Update the data displayed on screen.
Refresh Screen
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Status
Connection Status - PPPoE
If using PPPoE (PPP over Ethernet), a screen like the following example will be dis-
played when the "Connection Details" button is clicked.
Figure 21: PPPoE Status Screen
Data - PPPoE Screen
Connection
The hardware address of this device, as seen by remote
devices on the Internet. (This is different to the hardware
address seen by devices on the local LAN.)
Physical Address
The IP Address of this device, as seen by Internet users.
This address is allocated by your ISP (Internet Service
Provider).
IP Address
The Network Mask associated with the IP Address above.
Network Mask
This indicates whether or not the connection is currently
established.
PPPoE Link Status
•
If the connection does not exist, the "Connect" button
can be used to establish a connection.
•
If the connection currently exists, the "Disconnect"
button can be used to break the connection.
Connection Log
Connection Log
•
•
The Connection Log shows status messages relating to
the existing connection.
The most common messages are listed in the table
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
below.
•
The "Clear Log" button will restart the Log, while the
Refresh button will update the messages shown on
screen.
Buttons
If not connected, establish a connection to your ISP.
If connected to your ISP, hang up the connection.
Connect
Disconnect
Clear Log
Delete all data currently in the Log. This will make it easier
to read new messages.
Update the data on screen.
Refresh
Connection Log Messages
Message
Description
Connect on Demand
Connection attempt has been triggered by the "Connect
automatically, as required" setting.
Manual connection
Connection attempt started by the "Connect" button.
Preparing line for connection attempt.
Reset physical connec-
tion
Connecting to remote
server
Attempting to connect to the ISP's server.
Remote Server located
Start PPP
ISP's Server has responded to connection attempt.
Attempting to login to ISP's Server and establish a PPP
connection.
PPP up successfully
Idle time-out reached
Able to login to ISP's Server and establish a PPP con-
nection.
The connection has been idle for the time period speci-
fied in the "Idle Time-out" field. The connection will now
be terminated.
Disconnecting
The current connection is being terminated, due to either
the "Idle Time-out" above, or "Disconnect" button being
clicked.
Error: Remote Server
not found
ISP's Server did not respond. This could be a Server
problem, or a problem with the link to the Server.
Error: PPP Connection
failed
Unable to establish a PPP connection with the ISP's
Server. This could be a login problem (name or pass-
word) or a Server problem.
Error: Connection to
Server lost
The existing connection has been lost. This could be
caused by a power failure, a link failure, or Server fail-
ure.
Error: Invalid or un-
known packet type
The data received from the ISP's Server could not be
processed. This could be caused by data corruption
(from a bad link), or the Server using a protocol which is
not supported by this device.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Status
Connection Status - PPTP
If using PPTP (Peer-to-Peer Tunneling Protocol), a screen like the following example
will be displayed when the "Connection Details" button is clicked.
Figure 22: PPTP Status Screen
Data - PPTP Screen
Connection
The hardware address of this device, as seen by remote
devices on the Internet. (This is different to the hardware
address seen by devices on the local LAN.)
Physical Ad-
dress
The IP Address of this device, as seen by Internet users. This
address is allocated by your ISP (Internet Service Provider).
IP Address
•
•
•
•
This indicates whether or not the connection is currently
established.
Connection
Status
If the connection does not exist, the Connect button can be
used to establish a connection.
If the connection currently exists, the Disconnect button
can be used to break the connection.
Normally, it is not necessary to use the Connect and
Disconnect buttons unless the setting "Connect automati-
cally, as required" is disabled.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Connection Log
•
•
The Connection Log shows status messages relating to
the existing connection.
Connection Log
The "Clear Log" button will restart the Log, while the Re-
fresh button will update the messages shown on screen.
Buttons
If not connected, establish a connection to your ISP.
If connected to your ISP, terminate the connection.
Connect
Disconnect
Clear Log
Delete all data currently in the Log. This will make it easier to
read new messages.
Update the data on screen.
Refresh
Connection Status - L2TP
If using L2TP, a screen like the following example will be displayed when the "Con-
nection Details" button is clicked.
Figure 23: L2TP Status Screen
Data - L2TP Screen
Internet
The hardware address of this device, as seen by remote
devices on the Internet. (This is different to the hardware
address seen by devices on the local LAN.)
Physical Ad-
dress
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Status
The IP Address of this device, as seen by Internet users. This
address is allocated by your ISP (Internet Service Provider).
IP Address
This indicates whether or not the connection is currently estab-
lished.
Connection
Status
•
•
•
If the connection does not exist, the Connect button can be
used to establish a connection.
If the connection currently exists, the Disconnect button
can be used to break the connection.
Normally, it is not necessary to use the Connect and
Disconnect buttons unless the setting "Connect automati-
cally, as required" is disabled.
Connection Log
Connection Log
•
•
The Connection Log shows status messages relating to
the existing connection.
The "Clear Log" button will restart the Log, while the Re-
fresh button will update the messages shown on screen.
Buttons
If not connected, establish a connection to your ISP.
If connected to your ISP, hang up the connection.
Connect
Disconnect
Clear Log
Delete all data currently in the Log. This will make it easier to
read new messages.
Update the data on screen.
Refresh
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Connection Status - Telstra Big Pond
An example screen is shown below.
Figure 24: Telstra Big Pond Status Screen
Data - Big Pond Screen
Connection
The hardware address of this device, as seen by remote
Physical Address
devices. (This is different to the hardware address seen by
devices on the local LAN.)
The IP Address of this device, as seen by Internet users.
This address is allocated by your ISP (Internet Service Pro-
vider).
IP Address
This indicates whether or not the connection is currently
established.
Connection
Status
•
•
•
If the connection does not exist, the "Connect" button can
be used to establish a connection.
If the connection currently exists, the "Disconnect" button
can be used to break the connection.
Normally, it is not necessary to use the Connect and
Disconnect buttons unless the setting "Connect auto-
matically, as required" is disabled.
Connection Log
Connection Log
•
The Connection Log shows status messages relating to
the existing connection.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Status
•
The Clear Log button will restart the Log, while the Re-
fresh button will update the messages shown on screen.
Buttons
If not connected, establish a connection to Telstra Big Pond.
If connected to Telstra Big Pond, terminate the connection.
Connect
Disconnect
Clear Log
Delete all data currently in the Log. This will make it easier to
read new messages.
Update the data on screen.
Refresh
Connection Details - SingTel RAS
If using the SingTel RAS access method, a screen like the following example will be
displayed when the "Connection Details" button is clicked.
Figure 25: Connection Details - RAS
Data - RAS Screen
Internet
The RAS plan (connection speed) currently used.
RAS Plan
The hardware address of this device, as seen by remote
devices on the Internet. (This is different to the hardware
address seen by devices on the local LAN.)
Physical Ad-
dress
The IP Address of this device, as seen by Internet users. This
address is allocated by your ISP (Internet Service Provider).
IP Address
The Network Mask associated with the IP Address above.
Network Mask
The IP Address of the remote Gateway or Broadband router
associated with the IP Address above.
Default Gateway
The IP Address of the Domain Name Server which is currently
DNS IP Address
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
used.
•
•
This will show "Enabled" or "Disabled".
DHCP Client
If "Enabled", the Internet IP Address from your ISP is
allocated automatically upon connection. (Dynamic IP Ad-
dress). In this case the "Lease obtained" and "Remaining
lease time" fields provide additional information. Note that
the lease is automatically renewed on expiry; use the "Re-
new" button if you wish to manually renew the lease
immediately.
•
If "Disabled", the Internet IP Address from your ISP is
Fixed or Static. In this case, the "Release/Renew" button is
not operational.
Buttons
This button is only useful if the IP address shown above is
allocated automatically on connection. (Dynamic IP address).
Otherwise, it has no effect.
Release/Renew
•
This button will say "Release" if the Wireless Broadband
router is currently using an IP Address allocated by the
ISP's DHCP Server. Clicking the "Release" button will re-
lease the IP Address and break the connection.
•
If the button says "Renew", this indicates that the ISP's
DHCP Server has not allocated an IP Address for the
Wireless Broadband router. Clicking the "Renew" button
will re-establish the connection and obtain an IP Address
from the ISP's DHCP Server.
Update the data shown on screen.
Refresh
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation and Status
Connection Details - Fixed/Dynamic IP Address
If your access method is "Direct" (no login), a screen like the following example will be
displayed when the "Connection Details" button is clicked.
Figure 26: Connection Details - Fixed/Dynamic IP Address
Data - Fixed/Dynamic IP address Screen
Internet
The hardware address of this device, as seen by remote
devices on the Internet. (This is different to the hardware
address seen by devices on the local LAN.)
Physical Ad-
dress
The IP Address of this device, as seen by Internet users. This
address is allocated by your ISP (Internet Service Provider).
IP Address
The Network Mask associated with the IP Address above.
Network Mask
The IP Address of the remote Gateway or Broadband router
associated with the IP Address above.
Default Gateway
The IP Address of the Domain Name Server which is currently
used.
DNS IP Address
DHCP Client
This will show "Enabled" or "Disabled".
•
If "Enabled", the Internet IP Address from your ISP is
allocated automatically upon connection. (Dynamic IP Ad-
dress). In this case the "Lease obtained" and "Remaining
lease time" fields provide additional information. Note that
the lease is automatically renewed on expiry; use the "Re-
new" button if you wish to manually renew the lease
immediately.
•
If "Disabled", the Internet IP Address from your ISP is
Fixed or Static. In this case, the "Release/Renew" button is
not operational.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Buttons
•
•
This button is only useful if the IP address shown above is
allocated automatically on connection. (Dynamic IP ad-
dress). Otherwise, it has no effect.
Release/Renew
This button will say "Release" if the Wireless Broadband
router is currently using an IP Address allocated by the
ISP's DHCP Server. Clicking the "Release" button will re-
lease the IP Address and break the connection.
•
If the button says "Renew", this indicates that the ISP's
DHCP Server has not allocated an IP Address for the
Wireless Broadband router. Clicking the "Renew" button
will re-establish the connection and obtain an IP Address
from the ISP's DHCP Server.
Update the data shown on screen.
Refresh
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Advanced Features
6
This Chapter explains when and how to use the Wireless Broadband
router's "Advanced" Features.
Overview
The following advanced features are provided.
•
•
•
Access Control
Dynamic DNS
Internet
•
•
•
Communication Applications
Special Applications
Multi-DMZ
•
•
Virtual Servers
WAN Port
Access Control
This feature is accessed by the Access Control link on the Advanced menu.
Overview
The Access Control feature allows administrators to restrict the level of Internet Ac-
cess available to PCs on your LAN. With the default settings, everyone has
unrestricted Internet access.
To use this feature:
1. Set the desired restrictions on the "Default" group. All PCs are in the "Default"
group unless explicitly moved to another group.
2. Set the desired restrictions on the other groups ("Group 1", "Group 2", "Group 3"
and "Group 4") as needed.
3. Assign PC to the groups as required.
Restrictions are imposed by blocking "Services", or types of
connections. All common Services are pre-defined.
If required, you can also define your own Services.
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Access Control Screen
To view this screen, select the Access Control link on the Advanced menu.
Figure 27: Access Control Screen
Data - Access Control Screen
User Group
Select the desired Group. The screen will update to display
the settings for the selected Group. Groups are named
"Default", "Group 1", "Group 2", "Group 3" and "Group 4",
and cannot be re-named.
Group
Click this button to add or remove members from the current
Group.
"Members" But-
ton
•
If the current group is "Default", then members can not
be added or deleted. This group contains PCs not allo-
cated to any other group.
•
•
To remove PCs from the Default Group, assign them to
another Group.
To assign PCs to the Default Group, delete them from
the Group they are currently in.
See the following section for details of the Group Members
screen.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Internet Access
Restrictions
Select the desired options for the current group:
•
•
•
None - Nothing is blocked. Use this to create the least
restrictive group.
Block all Internet access - All traffic via the WAN port is
blocked. Use this to create the most restrictive group.
Block selected Services - You can select which Ser-
vices are to block. Use this to gain fine control over the
Internet access for a group.
If Internet access is being blocked, you can choose to apply
the blocking only during scheduled times. (If access is not
blocked, no Scheduling is possible, and this setting has no
effect.)
Block by Sched-
ule
Clicking this will open a sub-window where you can define or
modify the Schedule.
Define Schedule
Button
This lists all defined Services. Select the Services you wish
to block. To select multiple services, hold the CTRL key while
selecting. (On the Macintosh, hold the SHIFT key rather than
CTRL.)
Services
If you wish to define additional Services, or manage the
Service list, click this button to open the "Services" screen.
Edit Service List
Button
Buttons
Click this button to add or remove members from the current
Group.
Members
If the current group is "Default", then members can not be
added or deleted. This group contains PCs not allocated to
any other group.
See the following section for details of the Group Members
screen.
Click this to open a sub-window where you can define or
modify the Schedule.
Define Schedule
Edit Service List
View Log
If you wish to define additional Services, or manage the
Service list, click this button to open the "Services" screen.
Click this to open a sub-window where you can view the
"Access Control" log. This log shows attempted Internet
accesses which have been blocked by the Access Control
feature.
Click this to clear and restart the "Access Control" log, mak-
ing new entries easier to read.
Clear Log
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Group Members Screen
This screen is displayed when the Members button on the Access Control screen is
clicked.
Figure 28: Group Members
Use this screen to add or remove members (PCs) from the current group.
•
The "Del >>" button will remove the selected PC (in the Members list) from the
current group.
•
The "<< Add" button will add the selected PC (in the Other PCs list) to the current
group.
PCs not assigned to any group will be in the
"Default" group.
PCs deleted from any other Group will be added
to the "Default" group.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Default Schedule Screen
This screen is displayed when the Define Schedule button on the Access Control
screen is clicked.
•
•
This schedule can be (optionally) applied to any Access Control Group.
Blocking will be performed during the scheduled time (between the "Start" and
"Finish" times.)
•
•
•
Two (2) separate sessions or periods can be defined.
Times must be entered using a 24 hr clock.
If the time for a particular day is blank, no action will be performed.
Figure 29: Default Schedule Screen
Data - Default Schedule Screen
Each day of the week can scheduled independently.
Day
Two (2) separate sessions or periods can be defined. Session
2 can be left blank if not required.
Session 1
Session 2
Enter the start using a 24 hr clock.
Start Time
Enter the finish time using a 24 hr clock.
Finish Time
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Services Screen
This screen is displayed when the Edit Service List button on the Access Control
screen is clicked.
Figure 30: Access Control - Services
Data - Services Screen
Available Services
This lists all the available services.
Available Ser-
vices
Use this to delete the selected Service from the list.
"Delete" button
Add New Service
Name
Enter a descriptive name to identify this service.
Select the correct type for this Service.
Type
If the "Type" (above) is TCP, UDP, or TCP/UDP, enter the port
number for this Service. If a port range is required, enter the
beginning of the range here, and the end of the range in the
"Finish Port" field.
Start Port
If the "Type" (above) is TCP, UDP, or TCP/UDP, this field can
be used to enter the end of range of port numbers. This can be
left blank if not required.
Finish Port
ICMP Type
If the "Type" (above) is ICMP, enter the ICMP type here.
Otherwise, this field should be left blank.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Access Control Log
To check the operation of the Access Control feature, an Access Control Log is pro-
vided. Click the View Log button on the Access Control screen to view this log.
This log shows attempted Internet accesses which have been blocked by the Access
Control function.
Data shown in this log is as follows:
Date and Time of the attempted access.
Date/Time
If known, the name of the PC whose access was blocked.
Name
The IP Address of the PC or device whose access request
was blocked
Source IP address
The hardware or physical address of the PC or device whose
access request was blocked
MAC address
Destination
The destination URL or IP address
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Dynamic DNS (Domain Name Server)
This free service is very useful when combined with the Virtual Server feature. It
allows Internet users to connect to your Virtual Servers using a URL, rather than an IP
Address.
This also solves the problem of having a dynamic IP address. With a dynamic IP
address, your IP address may change whenever you connect, which makes it difficult
to connect to you.
The Service works as follows:
1. You must register for the service at one of the listed DDNS Service Providers.
2. After registration, follow the service provider's procedure to request a Domain
Name and have it allocated to you.
3. Enter your DDNS data on the Wireless Broadband router's DDNS screen.
4. The Wireless Broadband router will then automatically ensure that your current IP
Address is recorded at the DDNS server.
If the DDNS Service provides software to perform this "IP address update"; you
should disable the "Update" function, or not use the software at all.
5. From the Internet, users will be able to connect to your Virtual Servers (or DMZ
PC) using your Domain Name.
Dynamic DNS Screen
Select Advanced on the main menu, then Dynamic DNS, to see a screen like the
following:
Figure 31: DDNS Screen
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Data - Dynamic DNS Screen
DDNS Data
Select the desired DDNS Service provider. To disable DDNS,
select "None".
DDNS Service
Click this button to open a new window and connect to the
Web site for the selected DDNS service provider.
Web Site Button
Enter your Username for the DDNS Service.
User Name
Password
Enter your current password for the DDNS Service.
•
Enter the domain name allocated to you by the DDNS
Service.
Domain Name
•
If you have more than one domain name, enter the name
you wish to use. This device supports one name only.
DDNS Status
•
•
This message is returned by the DDNS Server.
Normally, this message should be something like "Update
successful" (current IP address was updated on the DDNS
server).
•
If the message is "No host", this indicates the host name
entered was not allocated to you. If you see this, or some
other error message, you need to contact the DDNS Ser-
vice and correct the problem.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Advanced Internet Screen
This screen allows configuration of all advanced features relating to Internet access.
•
•
•
•
Communication Applications
Special Applications
Multi-DMZ
URL Filter
An example screen is shown below.
Figure 32: Internet Screen
Communication Applications
Most applications are supported transparently by the Wireless Broadband router. But
sometimes it is not clear which PC should receive an incoming connection. This
problem could arise with the Communication Applications listed on this screen.
If this problem arises, you can use this screen to set which PC should receive an
incoming connection, as described below.
Communication Applications
This lists applications which may generate incoming con-
nections, where the destination PC (on your local LAN) is
unknown.
Select an Applica-
tion
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
This lists the PCs on your LAN.
Send incoming
calls to
•
•
•
If necessary, you can add PCs manually, using the "PC
Database" option on the advanced menu.
For each application listed above, you can choose a
destination PC.
There is no need to "Save" after each change; you can
set the destination PC for each application, then click
"Save".
Special Applications
If you use Internet applications which use non-standard connections or port numbers,
you may find that they do not function correctly because they are blocked by the
Wireless Broadband router's firewall. In this case, you can define the application as a
"Special Application".
Special Applications Screen
This screen can be reached by clicking the Special Applications button on the Internet
screen.
You can then define your Special Applications. You will need detailed information
about the application; this is normally available from the supplier of the application.
Also, note that the terms "Incoming" and "Outgoing" on this screen refer to traffic from
the client (PC) viewpoint
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Figure 33: Special Applications Screen
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Data - Special Applications Screen
Enter a descriptive name to identify this Special Application.
Name
•
•
Type - Select the protocol (TCP or UDP) used when you receive
data from the special application or service. (Note: Some applica-
tions use different protocols for outgoing and incoming data).
Incoming
Ports
Start - Enter the beginning of the range of port numbers used by
the application server, for data you receive. If the application
uses a single port number, enter it in both the "Start" and "Finish"
fields.
•
•
•
Finish - Enter the end of the range of port numbers used by the
application server, for data you receive.
Type - Select the protocol (TCP or UDP) used when you send
data to the remote system or service.
Outgoing
Ports
Start - Enter the beginning of the range of port numbers used by
the application server, for data you send to it. If the application
uses a single port number, enter it in both the "Start" and "Finish"
fields.
•
Finish - Enter the end of the range of port numbers used by the
application server, for data you send to it. If the application uses
a single port number, enter it in both the "Start" and "Finish"
fields.
Using a Special Application
•
•
Configure the Special Applications screen as required.
On your PC, use the application normally. Remember that only one (1) PC can
use each Special application at any time. Also, when 1 PC is finished using a par-
ticular Special Application, there may need to be a "Time-out" before another PC
can use the same Special Application. The "Time-out" period may be up to 3 min-
utes.
If an application still cannot function correctly,
try using the "DMZ" feature.
Multi-DMZ
This feature, if enabled, allows the DMZ computer or computers on your LAN to be
exposed to all users on the Internet.
•
•
•
This allows almost any application to be used on the "DMZ PC".
The "DMZ PC" will receive all "Unknown" connections and data.
If the DMZ feature is enabled, you must select the PC to be used as the "DMZ
PC".
To use this feature:
•
•
Enter an IP address allocated to you by your ISP into the WAN IP address field.
Select the PC to be the DMZ PC for traffic sent to this IP address.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
•
Enable this DMZ.
If you have multiple Internet IP addresses, you can assign one DMZ PC for each
Internet IP address.
If you only have 1 WAN IP address, only "DMZ 1" can be used, and only one (1) PC
can be the DMZ PC. The current WAN IP address is displayed. If this address is
assigned upon connection, and no connection currently exists, then this address will
be blank or 0.0.0.0.
The "DMZ PC" is effectively outside the Firewall, mak-
ing it more vulnerable to attacks. For this reason, you
should only enable the DMZ feature when required.
URL Filter
The URL Filter allows you to block access to undesirable Web site
•
To use this feature, you must define "filter strings". If the "filter string" appears in a
requested URL, the request is blocked.
•
Enabling the URL Filter also affects the Internet Access Log. If Enabled, the
"Destination" field in the log will display the URL. Otherwise, it will display the IP
Address.
•
The URL Filter can be Enabled or Disabled on the Advanced Internet screen.
URL Filter Screen
Click the "Configure URL Filter" button on the Internet screen to access the URL Filter
screen. An example screen is shown below.
Figure 34: URL Filter Screen
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Data - URL Filter Screen
Filter Strings
This lists any existing entries. If you have not entered any val-
ues, this list will be empty.
Current Entries
To add an entry to the list, enter it here, and click the "Add"
button.
Add Filter
String
An entry may be a Domain name (e.g. www.trash.com) or simply
a string. (e.g. ads/ )
Any URL which contains ANY entry ANYWHERE in the URL will
be blocked.
Buttons
Use these buttons to delete the selected entry or all entries, as
required. Multiple entries can be selected by holding down the
CTRL key while selecting. (On the Macintosh, hold the SHIFT
key while selecting.)
Delete/Delete
All
Use this to add the current Filter String to the site list.
Add
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Virtual Servers
This feature, sometimes called Port Forwarding, allows you to make Servers on your
LAN accessible to Internet users. Normally, Internet users would not be able to ac-
cess a server on your LAN because:
•
•
Your Server does not have a valid external IP Address.
Attempts to connect to devices on your LAN are blocked by the firewall in this
device.
The "Virtual Server" feature solves these problems and allows Internet users to con-
nect to your servers, as illustrated below.
Figure 35: Virtual Servers
IP Address seen by Internet Users
Note that, in this illustration, both Internet users are connecting to the same IP Ad-
dress, but using different protocols.
To Internet users, all virtual Servers on your LAN have the same IP Address.
This IP Address is allocated by your ISP.
This address should be static, rather than dynamic, to make it easier for Internet users
to connect to your Servers.
However, you can use the DDNS (Dynamic DNS) feature to allow users to connect to
your Virtual Servers using a URL, instead of an IP Address.
Virtual Servers Screen
The Virtual Servers screen is reached by the Virtual Servers link on the Advanced
screen. An example screen is shown below.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Figure 36: Virtual Servers Screen
This screen lists a number of pre-defined Servers, and allows you to define your own
Servers. Details of the selected Server are shown in the "Properties" area.
Data - Virtual Servers Screen
Servers
This lists a number of pre-defined Servers, plus any Servers
you have defined. Details of the selected Server are shown in
the "Properties" area.
Servers
Properties
Enable
Use this to Enable or Disable support for this Server, as
required.
Select the PC for this Server. The PC must be running the
appropriate Server software.
PC (Server)
Select the protocol (TCP or UDP) used by the Server.
Protocol
Enter the range of port numbers which the Server software is
configured to use.
Internal (LAN)
Ports
Traffic from the Internet using this range of port numbers will
be sent to the Server. This is normally the same as the
Internal Port Numbers. If it is different, this device will perform
a "mapping" or "translation" function, allowing the server to
use a different port range to the clients.
External
(WAN) Ports.
Buttons
Delete
Delete the current Virtual Server entry. Note that the pre-
defined Servers can not be deleted. Only Servers you have
defined yourself can be deleted.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
This will delete any Servers you have defined, and set the
Defaults
pre-defined Servers to use their default port numbers.
This will cause the "Enable" setting of all Virtual Servers to be
set OFF.
Disable All
Clear Form
Clear all data from the "Properties" area, ready for input of a
new Virtual Server entry.
Update the current Virtual Server entry, using the data shown
in the "Properties" area on screen.
Update Selected
Server
Add a new entry to the Virtual Server list, using the data
shown in the "Properties" area on screen. The entry selected
in the list is ignored, and has no effect.
Add as new
Server
For each entry, the PC must be running the
appropriate Server software.
Defining your own Virtual Servers
If the type of Server you wish to use is not listed on the Virtual Servers screen, you
can define and manage your own Servers:
1. Click "Clear Form"
Create a new Server:
Modify (Edit) a Server:
2. Enter the required data, as described above.
3. Click "Add".
4. The new Server will now appear in the list.
1. Select the desired Server from the list
2. Make any desired changes (for example, change the
Enable/Disable setting).
3. Click "Update" to save changes to the selected
Server.
1. Select the entry from the list.
2. Click "Delete".
Delete a Server:
Note: You can only delete Servers you have defined.
Pre-defined Server cannot be deleted.
From the Internet, ALL Virtual Servers have the IP
Address allocated by your ISP.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Connecting to the Virtual Servers
Once configured, anyone on the Internet can connect to your Virtual Servers. They
must use the Internet IP Address (the IP Address allocated to you by your ISP).
e.g.
http://203.70.212.52
ftp://203.70.212.52
It is more convenient if you are using a Fixed IP Address from your ISP, rather than
Dynamic. However, you can use the Dynamic DNS feature, described in the following
section, to allow users to connect to your Virtual Servers using a URL, rather than an
IP Address.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
WAN Port Configuration
The WAN Port option is on the Advanced menu.
Figure 37: WAN Port Screen
Data - WAN Port Screen
Identification
Normally, there is no need to change the default name, but if
your ISP requests that you use a particular Hostname, enter it
here.
Hostname
If your ISP provided a domain name, enter it here. Otherwise,
this may be left blank.
Domain Name
Also called Network Adapter Address or Physical Address.
This is a low-level identifier, as seen from the WAN port.
WAN Port MAC
Address
Normally there is no need to change this, but some ISPs
require a particular value, often that of the PC initially used for
Internet access.
You can use the Copy from PC button to copy your PC's
address into this field, the Default button to insert the default
value, or enter a value directly.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
IP Address
Also called Dynamic IP Address. This is the default, and the
most common.
Leave this selected if your ISP allocates an IP Address to the
Wireless Broadband router upon connection.
IP Address
is assigned
automatically
Also called Static IP Address. Select this if your ISP has allo-
cated you a fixed IP Address. If this option is selected, the
following data must be entered.
Specified IP
Address
•
IP Address.
The IP Address allocated by the ISP.
•
Network Mask
This is also supplied by your ISP. It must be compatible
with the IP Address above.
•
Gateway IP Address
The address of the broadband router or gateway, as sup-
plied by your ISP.
Note:
•
For "PPPoE" connections, the Network Mask and Gateway
IP address are NOT required.
•
For "PPPoE Unnumbered IP" connections, the Gateway IP
address is NOT required.
DNS
The DNS (Domain Name Server) address will be obtained
automatically from your ISP's server.
Note that if using a fixed IP address, with no login (login is set
to "None"), then no Server is used, so this option cannot be
used.
Automatically
obtain from
Serve
If this option is selected, you must enter the IP address of the
DNS (Domain Name Server) you wish to use.
Use this DNS
Note: If the DNS is unavailable, the "Backup DNS", entered on the "Options"
screen, will be used.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Login
If your ISP does not use a login method (username, password)
Login Method
for Internet access, leave this at the default value None (Di-
rect connection). Otherwise, check the documentation from
your ISP, select the login method used, and enter the required
data.
•
PPPoE - this is the most common login method, widely
used with DSL modems. Normally, your ISP will have pro-
vided some software to connect and login. This software is
no longer required, and should not be used.
•
PPPoE (Unnumbered IP) - this can only be used if your
ISP supports this system, and has allocated you multiple
IP addresses. If selected, you must also select "Specified
IP Address" above and enter one of the IP addresses allo-
cated to you by your ISP.
•
PPTP - this is mainly used in Europe. You need to know
the PPTP Server address as well as your name and pass-
word.
•
•
Big Pond Cable - for Australia only.
SingTel RAS - for Singapore only.
•
L2TP - this is not widely used. You need to know the
PPTP Server address as well as your name and password.
The User Name (or account name) provided by your ISP.
Login User
Name
Enter the password for the login name above.
Login Password
RAS Plan
For SingTel customers only, select the RAS plan you are on.
If using PPTP, L2TP, or Big Pond Cable, the Server address is
required.
Server Address
•
For PPTP and L2TP, you can select and enter either the
name or IP address of your ISP's server.
•
For Big Pond Cable, you must select "IP" and enter the IP
address of the Big Pond Server.
Select the desired option:
Connection
Behavior
•
Auto
An Internet connection is automatically made when re-
quired, and disconnected when idle for the time period
specified by the "Auto-disconnect Idle Time-out".
•
•
Manual
You must manually establish and terminate the connec-
tion.
Keep alive (maintain connection)
The connection will never be disconnected by this device.
If disconnected by your ISP, the connection will be re-
established immediately. (However, this does not ensure
that your Internet IP address will remain unchanged.)
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Auto-disconnect
Idle Time-out
This field has no effect unless using the Automatic Con-
nect/Disconnect setting.
If using this setting, enter the desired idle time-out period
(in minutes). After the connection to your ISP has been idle
for this time period, the connection will be terminated.
Buttons
Default
Inserts the default MAC address into the MAC address field.
You must click "Save" to actually change the address used.
Inserts the MAC address from your PC into the MAC address
field. You must click "Save" to actually change the address
used.
Copy from PC
Save
Save your changes to the Wireless Broadband router.
Reverse any changes made since the last "Save".
Cancel
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
Advanced Administration
7
This Chapter explains the settings available via the "Administration"
section of the menu.
Overview
Normally, it is not necessary to use these screens, or change any settings. These
screens and settings are provided to deal with non-standard situations, or to provide
additional options for advanced users.
The available settings and features are:
Backup or restore the configuration file for the Wireless Broad-
band router. This file contains all the configuration data.
Config File
View or clear all logs, set E-Mailing of log files.
Ping, DNS Lookup.
Logs
Network
Diagnostics
Various options, such as backup DNS, UPnP, and enable TFTP
firmware upgrade option.
Options
This is the list of PCs shown when you select the "DMZ PC" or a
"Virtual Server". This database is maintained automatically, but
you can add and delete entries for PCs which use a Fixed (Static)
IP Address.
PC Database
Quality of Service.
QoS
Allow settings to be changed from the Internet..
Remote
Administra-
tion
Only required if your LAN has other Broadband routers or Gate-
ways.
Routing
Firewall and other security-related settings. Normally, the default
settings do not need to be changed.
Security
Upgrade the Firmware (software) installed in your Wireless Broad-
band router.
Upgrade
Firmware
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Config File
This feature allows you to download the current settings from the Wireless Broadband
router, and save them to a file on your PC.
You can restore a previously-downloaded configuration file to the Wireless Broadband
router, by uploading it to the Wireless Broadband router.
This screen also allows you to set the Wireless Broadband router back to its factory
default configuration. Any existing settings will be deleted.
An example Config File screen is shown below.
Figure 38: Config Screen
Data - Config File Screen
Use this to download a copy of the current configuration, and
Backup Config
store the file on your PC. Click Download to start the download.
This allows you to restore a previously-saved configuration file
back to the Wireless Broadband router.
Restore Config
Click Browse to select the configuration file, then click Restore to
upload the configuration file.
WARNING!
Uploading a configuration file will destroy (overwrite) ALL of the
existing settings.
Clicking the Restore Defaults button will reset the Wireless
Default Config
Broadband router to its factory default settings.
WARNING!
This will delete ALL of the existing settings.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Logs
The Logs record various types of activity on the Wireless Broadband router. This data
is useful for troubleshooting, but enabling all logs will generate a large amount of data
and adversely affect performance.
Since only a limited amount of log data can be stored in the Wireless Broadband
router, log data can also be E-mailed to your PC.
Figure 39: Logs Screen
Data - Logs Screen
Enable Logs
If selected, Outgoing Internet connections are logged.
Normally, the (Internet) "Destination" will be shown as an IP
address. But if the "URL Filter" is enabled, the "Destination"
will be shown as a URL.
Outgoing
If enabled, the log will include attempted outgoing connec-
tions which have been blocked by the "Access Control"
feature.
Access Control
DoS Attacks
If enabled, this log will show details of DoS (Denial of
Service) attacks which have been blocked by the built-in
Firewall.
Select the correct Timezone for your location. This is re-
quired for the date/time shown on the logs to be correct.
Timezone
Use this to view each log, as required.
View Log button
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Use this to restart the required log. This makes it easier to
read the latest entries.
Clear Log button
E-Mail Logs
If enabled, an E-mail will be sent immediately if a DoS
(Denial of Service) attack is detected. If enabled, the E-mail
address information must be provided.
Send E-mail alert
Enabled the logs you wish to send. If no checkboxes are
enabled, no logs will be sent.
E-mail Logs
Send
Select the desired option for sending the log by E-mail.
•
•
When log is full - The time is not fixed. The log will be
sent when the log is full, which will depend on the vol-
ume of traffic.
Every day, Every Monday ... - The log is sent on the
interval specified.
•
•
•
•
If "Every day" is selected, the log is sent at the time
specified.
If the day is specified, the log is sent once per
week, on the specified day.
Select the time of day you wish the E-mail to be
sent.
If the log is full before the time specified to send it,
it will be sent regardless.
E-Mail Address
E-mail Address
Enter the E-mail address the Log is to be sent to. The E-
mail will also show this address as the Sender's address.
Enter the text string to be shown in the "Subject" field for
the E-mail.
Subject
Enter the address (domain name) or IP address of the
SMTP (Simple Mail Transport Protocol) Server you use for
outgoing E-mail.
SMTP Server
Enter the port number used to connect to the SMTP Server.
The default value is 25.
Port No.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Network Diagnostics
This screen allows you to perform a "Ping" or a "DNS lookup". These activities can be
useful in solving network problems.
An example Network Diagnostics screen is shown below.
Figure 40: Network Diagnostics Screen
Data - Network Diagnostics Screen
Ping
Enter the IP address you wish to ping. The IP address can be
on your LAN, or on the Internet. Note that if the address is on
the Internet, and no connection currently exists, you could get
a "Timeout" error. In that case, wait a few seconds and try
again.
Ping IP Address
After entering the IP address, click this button to start the
"Ping" procedure. The results will be displayed in the Ping
Results pane.
Ping Button
DNS Lookup
Enter the Domain name or URL for which you want a DNS
(Domain Name Server) lookup. Note that if the address in on
the Internet, and no connection currently exists, you could get
a "Timeout" error. In that case, wait a few seconds and try
again.
Domain
name/URL
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
After entering the Domain name/URL, click this button to start
the "DNS Lookup" procedure. The results will be displayed in
the DNS Lookup Results pane.
Lookup Button
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Options
This screen allows advanced users to enter or change a number of settings. For
normal operation, there is no need to use this screen or change any settings.
An example Options screen is shown below.
Figure 41: Options Screen
Data - Options Screen
Backup DNS
Enter the IP Address of the DNS (Domain Name Servers) here.
These DNS will be used only if the primary DNS is unavailable.
DNS IP Ad-
dress
TFTP
•
•
If enabled, TFTP (Trivial FTP) can be used to upgrade the
firmware in this device. This is normally not required; a Win-
dows utility is available for this purpose.
Enable Firm-
ware
You must obtain the firmware upgrade file first; instructions
for using TFTP will be available with the upgrade.
UPnP
•
UPnP (Universal Plug and Play) allows automatic discovery
and configuration of equipment attached to your LAN. UPnP
is by supported by Windows ME, XP, or later.
Enable UPnP
Services
•
•
If Enabled, this device will be visible via UPnP.
If Disabled, this device will not be visible via UPnP.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
•
•
If checked, then UPnP users can change the configuration.
Allow Configu-
ration...
If Disabled, UPnP users can only view the configuration. But
currently, this restriction only applies to users running Win-
dows XP, who access the Properties via UPnP. (e.g. Right -
click the Wireless Broadband router in My Network Places,
and select Properties)
•
•
If checked, then UPnP users can disable Internet access via
this device.
Allow Internet
access to be
disabled
If Disabled, UPnP users can NOT disable Internet access
via this device. But currently, this restriction only applies to
users running Windows XP, who access the Properties via
UPnP. (e.g. Right - click the Wireless Broadband router in
My Network Places, and select Properties)
MTU
MTU
•
MTU (Maximum Transmission Unit) value should only be
changed if advised to do so by Technical Support.
•
•
Enter a value between 1 and 1500.
This device will still auto-negotiate with the remote server, to
set the MTU size. The smaller of the 2 values (auto-
negotiated, or entered here) will be used.
•
For direct connections (not PPPoE or PPTP), the MTU used
is always 1500.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
PC Database
The PC Database is used whenever you need to select a PC (e.g. for the "DMZ" PC).
It eliminates the need to enter IP addresses. Also, you do not need to use fixed IP
addresses on your LAN.
PC Database Screen
An example PC Database screen is shown below.
Figure 42: PC Database
•
•
•
PCs which are "DHCP Clients" are automatically added to the database, and
updated as required.
By default, non-Server versions of Windows act as "DHCP Clients"; this setting is
called "Obtain an IP Address automatically".
The Wireless Broadband router uses the "Hardware Address" to identify each PC,
not the name or IP address. The "Hardware Address" can only change if you
change the PC's network card or adapter.
•
This system means you do NOT need to use Fixed (static) IP addresses on your
LAN. However, you can add PCs using Fixed (static) IP Addresses to the PC da-
tabase if required.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Data - PC Database Screen
This lists all current entries (PCs or network devices).
Known PCs
Name
If adding a new PC to the list, enter its name here. It is best if
this matches the PC's "hostname".
If adding a new PC to the list, enter the IP Address of the PC
here. The PC will be sent a "ping" to determine its hardware
address. If the PC is not available (not connected, or not pow-
ered On) you will not be able to add it.
IP Address
Buttons
Add
This will add the new PC to the list. The PC will be sent a "ping"
to determine its hardware address. If the PC is not available (not
connected, or not powered On) you will not be able to add it.
Delete the selected PC from the list. This should be done in 2
situations:
Delete
•
•
The PC has been removed from your LAN.
The entry is incorrect.
Update the data on screen.
Refresh
Display a read-only list showing full details of all entries in the
PC database.
Generate
Report
Advanced
View the Advanced version of the PC database screen - Ad-
Administration vanced PC Database. See below for details.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Advanced PC Database
This screen is displayed if the "Advanced" button on the PC Database is clicked. It
provides more control than the standard PC Database screen.
Figure 43: Advanced PC Database
Data - Advanced PC Database Screen
This lists all current entries (PCs or network devices).
Known PCs
Edit
Use this to change the data for the selected PC in the list. The
data for the selected PC will then be shown in the "Properties"
area, where it may be edited. (Click "Update" to save any
changes.)
Use this to Delete the selected PC from the list. This should be
done in 2 situations:
Delete
•
•
The PC has been removed from your LAN.
The entry is incorrect.
PC Properties
Name
If adding a new PC to the list, enter its name here. It is best if
this matches the PC's "hostname".
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Select the appropriate option:
IP Address
•
Automatic - The PC is set to be a DHCP client (Windows:
"Obtain an IP address automatically"). The Wireless Broad-
band router will allocate an IP address to this PC when
requested to do so. The IP address could change, but nor-
mally won't.
•
DCHP Client - Reserved IP Address - Select this if the PC
is set to be a DCHP client, and you wish to guarantee that
the Wireless Broadband router will always allocate the same
IP Address to this PC.
Enter the required IP address. Only the last field is required;
the other fields must match the Wireless Broadband router's
IP address.
•
Fixed IP Address - Select this if the PC is using a Fixed
(Static) IP address. Enter the IP address allocated to the
PC. (The PC must be configured to use this IP address.)
Select the appropriate option
MAC Address
•
Automatic discovery - Select this to have the Wireless
Broadband router contact the PC and find its MAC address.
This is only possible if the PC is connected to the LAN and
powered On.
•
MAC address is - Enter the MAC address on the PC. The
MAC address is also called the "Hardware Address", "Physi-
cal Address", or "Network Adapter Address". The Wireless
Broadband router uses this to provide a unique identifier for
each PC. Because of this, the MAC address can NOT be left
blank.
Buttons
Add a new PC to the list, using the data in the "Properties" box.
If "Automatic discovery" (for MAC address) is selected, the PC
will be sent a "ping" to determine its hardware address. This will
fail unless the PC is connected to the LAN, and powered on.
Add as New
Entry
Update (modify) the selected PC, using the data in the "Proper-
ties" box.
Update Se-
lected PC
Clear the "Properties" box, ready for entering data for a new PC.
Update the data on screen.
Clear Form
Refresh
Display a read-only list showing full details of all entries in the
PC database.
Generate
Report
Standard
Screen
Click this to view the standard PC Database screen.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
QoS
Quality of Service (QoS) ensures better service to high-priority service.
Figure 44: QoS Screen
Data - QoS Screen
QoS Setting
It displays the queue name.
QoS Queue
Select the desired traffic type(s).
Traffic Type in
the Queue
Enter the priority value (1~20) of the policy.
Priority
Enter the desired values for the inbound and outbound traffic
limitation.
Traffic Limit
Click this button to access the Advanced Settings sub-screen.
See the following section for more details.
Advanced Set-
tings
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Advanced Settings Screen
This screen is displayed if the "Advanced Settings" button on the QoS is clicked.
Figure 45: Advanced QoS Screen
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Data - Advanced QoS Screen
QoS Setting
Select the desired option.
QoS Method
•
•
Disabled
Follow existing packet classification
•
•
•
QoS Queue: It displays the queue type.
Priority: Enter the priority value (1~20) of the policy.
Reliability: Select the desired option from the drop-
down list.
•
Traffic Limit: Enter the desired values for the inbound
and outbound traffic limitation.
•
Use QoS Policies below
•
•
•
QoS Queue: It displays the queue type.
Priority: Enter the priority value (1~20) of the policy.
Reliability: Select the desired option from the drop-
down list.
•
Traffic Limit: Enter the desired values for the inbound
and outbound traffic limitation.
•
•
QoS Policy Name: It displays the name for the policy.
Traffic Definition: It displays the information of the traf-
fic.
•
•
•
Queue: Select the desired option.
Enable: Check this to enable this policy.
Define Traffic Button: Click this button to access the
sub-screen, and define the traffic for the selected pol-
icy.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Remote Admin
If enabled, this feature allows you to manage the Wireless Broadband router via the
Internet.
Figure 46: Remote Administration Screen
Data - Remote Administration Screen
Remote Administration
Check to allow administration/management via the Internet.
(To connect, see below).
Enable Remote
Management
If Disabled, this device will ignore Administration connection
attempts from the Internet.
Enter a port number between 1024 and 65535. The default for
HTTP (Web) connections is port 80, but using port 80 will
prevent the use of a Web "Virtual Server" on your LAN. So
using a different port number is recommended. The default
value is 8080.
Port Number
The port number must be specified in your Browser when you
connect. To specify the port number :
1. From a remote location, start your Browser.
2. In the "Address" or "Location" field, enter the Internet IP
address of this device (NOT the LAN IP address), followed
by the port number, as follows:
http://ip_address:port_number
Where:
ip_address is the Internet IP address of this device.
port_number is the port number assigned on this screen.
3. You should then be prompted for the password for this
device. (You must assign a password!)
To manage this device via the Internet, you need to know the
IP Address of this device, as seen from the Internet. This IP
Address is allocated by your ISP, and is shown here. But if
using a Dynamic IP Address, this value can change each time
you connect to your ISP. There are 2 solutions to this problem:
Current
IP Address
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
•
•
Have your ISP allocate you a Fixed IP address.
Use the DDNS feature (Advanced menu) so you can
connect using a Domain Name, rather than an IP address.
To connect from a remote PC via the Internet
1. Ensure your Internet connection is established, and start your Web Browser.
2. In the "Address" bar, enter "HTTP://" followed by the Internet IP Address of the
Wireless Broadband router. If the port number is not 80, the port number is also
required. (After the IP Address, enter ":" followed by the port number.)
e.g.
HTTP://123.123.123.123:8080
This example assumes the WAN IP Address is 123.123.123.123, and the port number
is 8080.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Routing
Overview
•
If you don't have other Broadband routers or Gateways on your LAN, you can
ignore the "Routing" page completely.
•
If the Wireless Broadband router is only acting as a Gateway for the local LAN
segment, ignore the "Routing" page even if your LAN has other Broadband
routers.
•
•
If your LAN has a standard Broadband router (e.g. Cisco) on your LAN, and the
Wireless Broadband router is to act as a Gateway for all LAN segments, enable
RIP (Routing Information Protocol) and ignore the Static Routing table.
If your LAN has other Gateways and Broadband routers, and you wish to control
which LAN segments use each Gateway, do NOT enable RIP (Routing Informa-
tion Protocol). Configure the Static Routing table instead. (You also need to
configure the other Broadband routers.)
•
If using Windows 2000 Data center Server as a software Broadband router,
enable RIP on the Wireless Broadband router, and ensure the following Windows
2000 settings are correct:
•
•
Open Routing and Remote Access
In the console tree, select Routing and Remote Access , [server name], IP
Routing, RIP
•
•
In the "Details" pane, right-click the interface you want to configure for RIP
version 2, and then click "Properties".
On the "General" tab, set Outgoing packet protocol to "RIP version 2 broad-
cast", and Incoming packet protocol to "RIP version 1 and 2".
Routing Screen
The routing table is accessed by the Routing link on the Administration menu.
Using this Screen
Generally, you will use either RIP (Routing Information Protocol) OR the Static Rout-
ing Table, as explained above, although is it possible to use both methods
simultaneously.
Static Routing Table
•
If RIP is not used, an entry in the routing table is required for each LAN segment
on your Network, other than the segment to which this device is attached.
•
The other Broadband routers must also be configured. See Configuring Other
Broadband routers on your LAN later in this chapter for further details and an ex-
ample.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Figure 47: Routing Screen
Data - Routing Screen
RIP
Check this to enable the RIP (Routing Information Protocol)
Enable RIP V1
feature of the Wireless Broadband router.
The Wireless Broadband router supports RIP 1 only.
Static Routing
This list shows all entries in the Routing Table.
Static Routing
Table Entries
•
The "Properties" area shows details of the selected item in
the list.
•
Change any the properties as required, then click the
"Update" button to save the changes to the selected entry.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
•
Destination IP Address - The network address of the
Properties
remote LAN segment. For standard class "C" LANs, the
network address is the first 3 fields of the Destination IP
Address. The 4th (last) field can be left at 0.
•
•
Network Mask - The Network Mask for the remote LAN
segment. For class "C" networks, the default mask is
255.255.255.0
Gateway IP Address - The IP Address of the Gateway or
Broadband router which the Wireless Broadband router
must use to communicate with the destination above.
(NOT the broadband router attached to the remote seg-
ment.)
•
Metric - The number of "hops" (broadband routers) to pass
through to reach the remote LAN segment. The shortest
path will be used. The default value is 2.
Buttons
Save
Save the RIP setting. This has no effect on the Static Routing
Table.
Add a new entry to the Static Routing table, using the data
shown in the "Properties" area on screen. The entry selected
in the list is ignored, and has no effect.
Add
Update the current Static Routing Table entry, using the data
shown in the "Properties" area on screen.
Update
Delete the current Static Routing Table entry.
Delete
Clear all data from the "Properties" area, ready for input of a
new entry for the Static Routing table.
Clear Form
Generate a read-only list of all entries in the Static Routing
table.
Generate Report
Configuring Other Broadband routers on your LAN
It is essential that all IP packets for devices not on the local LAN be passed to the
Wireless Broadband router, so that they can be forwarded to the external LAN, WAN,
or Internet. To achieve this, the local LAN must be configured to use the Wireless
Broadband router as the Default Route or Default Gateway.
Local Broadband router
The local broadband router is the Broadband router installed on the same LAN seg-
ment as the Wireless Broadband router. This broadband router requires that the
Default Route is the Wireless Broadband router itself. Typically, broadband routers
have a special entry for the Default Route. It should be configured as follows.
Normally 0.0.0.0, but check your broadband router
documentation.
Destination IP Address
Network Mask
Normally 0.0.0.0, but check your broadband router
documentation.
The IP Address of the Wireless Broadband router.
Gateway IP Address
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
1
Metric
Other Broadband routers on the Local LAN
Other broadband routers on the local LAN must use the Wireless Broadband router's
Local Broadband router as the Default Route. The entries will be the same as the
Wireless Broadband router's local broadband router, with the exception of the Gate-
way IP Address.
•
For a broadband router with a direct connection to the Wireless Broadband
router's local Broadband router, the Gateway IP Address is the address of the
Wireless Broadband router's local broadband router.
•
For broadband routers which must forward packets to another broadband router
before reaching the Wireless Broadband router's local broadband router, the
Gateway IP Address is the address of the intermediate broadband router.
Static Routing - Example
Figure 48: Routing Example
For the Wireless Broadband router's Routing Table
For the LAN shown above, with 2 broadband routers and 3 LAN segments, the Wire-
less Broadband router requires 2 entries as follows.
Entry 1 (Segment 1)
Destination IP Address
Network Mask
192.168.1.0
255.255.255.0 (Standard Class C)
Gateway IP Address
192.168.0.100 (Wireless Broadband
router's local Broadband router)
Metric
2
Entry 2 (Segment 2)
Destination IP Address
192.168.2.0
Network Mask
255.255.255.0 (Standard Class C)
192.168.0.100
Gateway IP Address
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Metric
3
For Broadband router A's Default Route
Destination IP Address
Network Mask
0.0.0.0
0.0.0.0
Gateway IP Address
192.168.0.1 (Wireless Broadband router's
IP Address)
For Broadband router B's Default Route
Destination IP Address
Network Mask
0.0.0.0
0.0.0.0
Gateway IP Address
192.168.1.80 (Wireless Broadband
router's local broadband router)
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Security
This screen allows you to set Firewall and other security-related options.
Figure 49: Security Screen
Data - Security Screen
DoS Firewall
If enabled, DoS (Denial of Service) attacks will be detected and
blocked. The default is enabled. It is strongly recommended that
this setting be left enabled.
Enable DoS
Firewall
Note:
•
A DoS attack does not attempt to steal data or damage your
PCs, but overloads your Internet connection so you can not
use it - the service is unavailable.
•
This device uses "Stateful Inspection" technology. This
system can detect situations where individual TCP/IP pack-
ets are valid, but collectively they become a DoS attack.
This setting affects the number of "half-open" connections
allowed.
Threshold
•
A "half-open" connection arises when a remote client con-
tacts the Server with a connection request, but then does
not reply to the Server's response.
•
While the optimum number of "half-open" connections
allowed (the "Threshold") depends on many factors, the
most important factor is the available bandwidth of your
Internet connection.
•
Select the setting to match the bandwidth of your Internet
connection.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Administration
Options
The ICMP protocol is used by the "ping" and "trace route" pro-
grams, and by network monitoring and diagnostic programs.
Respond to
ICMP
•
If checked, the Broadband VPN Broadband router will
respond to ICMP packets received from the Internet.
•
If not checked, ICMP packets from the Internet will be ig-
nored. Disabling this option provides a slight increase in
security.
The IPSec protocol is used to establish a secure connection,
and is widely used by VPN (Virtual Private Networking) pro-
grams.
Allow IPsec
•
•
If checked, IPSec connections are allowed.
If not checked, IPSec connections are blocked.
PPTP (Point to Point Tunneling Protocol) is widely used by VPN
(Virtual Private Networking) programs.
Allow PPTP
Allow L2TP
•
•
If checked, PPTP connections are allowed.
If not checked, PPTP connections are blocked.
L2TP is a protocol developed by Cisco for VPNs (Virtual Private
Networks).
•
•
If checked, L2TP connections are allowed.
If not checked, L2TP connections are blocked.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
Upgrade Firmware
The firmware (software) in the Wireless Broadband router can be upgraded using your
Web Browser.
You must first download the upgrade file, then select Upgrade on the Administration
menu. You will see a screen like the following.
Figure 50: Upgrade Firmware Screen
To perform the Firmware Upgrade:
1. Click the "Browse" button and navigate to the location of the upgrade file.
2. Select the upgrade file. Its name will appear in the Upgrade File field.
3. Click the "Start Upgrade" button to commence the firmware upgrade.
The Wireless Broadband router is unavailable during
the upgrade process, and must restart when the
upgrade is completed. Any connections to or
through the Wireless Broadband router will be lost.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Troubleshooting
A
This Appendix covers the most likely problems and their solutions.
Overview
This chapter covers some common problems that may be encountered while using
the Wireless Broadband router and some possible solutions to them. If you follow the
suggested steps and the Wireless Broadband router still does not function properly,
contact your dealer for further advice.
General Problems
Problem 1: Can't connect to the Wireless Broadband router to configure it.
Check the following:
Solution 1:
•
The Wireless Broadband router is properly installed, LAN con-
nections are OK, and it is powered ON.
•
Ensure that your PC and the Wireless Broadband router are on
the same network segment. (If you don't have a broadband
router, this must be the case.)
•
•
If your PC is set to "Obtain an IP Address automatically" (DHCP
client), restart it.
If your PC uses a Fixed (Static) IP address, ensure that it is using
an IP Address within the range 192.168.0.2 to 192.168.0.254 and
thus compatible with the Wireless Broadband router's default IP
Address of 192.168.0.1.
Also, the Network Mask should be set to 255.255.255.0 to match
the Wireless Broadband router.
In Windows, you can check these settings by using Control
Panel-Network to check the Properties for the TCP/IP protocol.
Internet Access
Problem 1: When I enter a URL or IP address I get a time out error.
A number of things could be causing this. Try the following trouble-
shooting steps.
Solution 1:
•
•
•
Check if other PCs work. If they do, ensure that your PCs IP
settings are correct. If using a Fixed (Static) IP Address, check
the Network Mask, Default gateway and DNS as well as the IP
Address.
If the PCs are configured correctly, but still not working, check
the Wireless Broadband router. Ensure that it is connected and
ON. Connect to it and check its settings. (If you can't connect to
it, check the LAN and power connections.)
If the Wireless Broadband router is configured correctly, check
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
your Internet connection (DSL/Cable modem etc) to see that it is
working correctly.
Problem 2: Some applications do not run properly when using the Wireless
Broadband router.
The Wireless Broadband router processes the data passing through
it, so it is not transparent.
Solution 2:
Use the Special Applications feature to allow the use of Internet
applications which do not function correctly.
If this does solve the problem you can use the DMZ function. This
should work with almost every application, but:
•
•
It is a security risk, since the firewall is disabled.
Only one (1) PC can use this feature.
Wireless Access
Problem 1: My PC can't locate the Wireless Access Point.
Check the following.
Solution 1:
•
Your PC is set to Infrastructure Mode. (Access Points are always
in Infrastructure Mode)
•
The SSID on your PC and the Wireless Access Point are the
same.
Remember that the SSID is case-sensitive. So, for example
"Workgroup" does NOT match "workgroup".
•
Both your PC and the Wireless Broadband router must have the
same setting for WEP. The default setting for the Wireless
Broadband router is disabled, so your wireless station should
also have WEP disabled.
•
•
If WEP is enabled on the Wireless Broadband router, your PC
must have WEP enabled, and the key must match.
If the Wireless Broadband router's Wireless screen is set to Allow
LAN access to selected Wireless Stations only, then each of your
Wireless stations must have been selected, or access will be
blocked.
•
To see if radio interference is causing a problem, see if connec-
tion is possible when close to the Wireless Broadband router.
Remember that the connection range can be as little as 100 feet
in poor environments.
Problem 2: Wireless connection speed is very slow.
The wireless system will connect at the highest possible speed,
depending on the distance and the environment. To obtain the high-
est possible connection speed, you can experiment with the
following:
Solution 2:
•
Wireless Broadband router location.
Try adjusting the location and orientation of the Wireless Broad-
band router.
•
Wireless Channel
If interference is the problem, changing to another channel may
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A - Troubleshooting
show a marked improvement.
Radio Interference
Other devices may be causing interference. You can experiment
by switching other devices Off, and see if this helps. Any "noisy"
devices should be shielded or relocated.
•
•
RF Shielding
Your environment may tend to block transmission between the
wireless stations. This will mean high access speed is only pos-
sible when close to the Wireless Broadband router.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
About Wireless LANs
B
This Appendix provides some background information about using
Wireless LANs (WLANs).
Modes
Wireless LANs can work in either of two (2) modes:
•
•
Ad-hoc
Infrastructure
Ad-hoc Mode
Ad-hoc mode does not require an Access Point or a wired (Ethernet) LAN. Wire-
less Stations (e.g. notebook PCs with wireless cards) communicate directly with
each other.
Infrastructure Mode
In Infrastructure Mode, one or more Access Points are used to connect Wireless
Stations (e.g. Notebook PCs with wireless cards) to a wired (Ethernet) LAN. The
Wireless Stations can then access all LAN resources.
Access Points can only function in "Infrastructure" mode,
and can communicate only with Wireless Stations which are
set to "Infrastructure" mode.
BSS/ESS
BSS
A group of Wireless Stations and a single Access Point, all using the same ID (SSID),
form a Basic Service Set (BSS).
Using the same SSID is essential. Devices with different SSIDs are unable to com-
municate with each other.
ESS
A group of Wireless Stations, and multiple Access Points, all using the same ID
(ESSID), form an Extended Service Set (ESS).
Different Access Points within an ESS can use different Channels. In fact, to reduce
interference, it is recommended that adjacent Access Points SHOULD use different
channels.
As Wireless Stations are physically moved through the area covered by an ESS, they
will automatically change to the Access Point which has the least interference or best
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B - About Wireless LANs
performance. This capability is called Roaming. (Access Points do not have or require
Roaming capabilities.)
Channels
The Wireless Channel sets the radio frequency used for communication.
•
Access Points use a fixed Channel. You can select the Channel used. This allows
you to choose a Channel which provides the least interference and best perform-
ance. In the USA and Canada, 11 channel are available. If using multiple Access
Points, it is better if adjacent Access Points use different Channels to reduce inter-
ference.
•
•
In "Infrastructure" mode, Wireless Stations normally scan all Channels, looking for
an Access Point. If more than one Access Point can be used, the one with the
strongest signal is used. (This can only happen within an ESS.)
If using "Ad-hoc" mode (no Access Point), all Wireless stations should be set to
use the same Channel. However, most Wireless stations will still scan all Chan-
nels to see if there is an existing "Ad-hoc" group they can join.
WEP
WEP (Wired Equivalent Privacy) is a standard for encrypting data before it is transmit-
ted.
This is desirable because it is impossible to prevent snoopers from receiving any data
which is transmitted by your Wireless Stations. But if the data is encrypted, then it is
meaningless unless the receiver can decrypt it.
If WEP is used, the Wireless Stations and the Access Point must have the same
settings for each of the following:
Off, 64 Bit, 128 Bit
WEP
Key
For 64 Bit encryption, the Key value must match.
For 128 Bit encryption, the Key value must match
Open System or Shared Key.
WEP Authentication
WPA-PSK
WPA-PSK is another standard for encrypting data before it is transmitted. This is a
later standard than WEP (Wired Equivalent Privacy), and provides greater security for
your data. Data is encrypted using a 256Bit key which is automatically generated and
changed often.
If all your Wireless stations support WPA-PSK, you should use this instead of WEP.
If WPA-PSK is used, the Wireless Stations and the Access Point must have the
same settings for each of the following:
Enter the same value on every station and the AP.
The PSK must be from 8 to 63 characters in length.
The 256Bit key used for the actual encryption is de-
rived from this key.
WPA PSK
(Pre-shared Key)
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Broadband router User Guide
The same encryption method must be used. The most
Encryption
common encryption method is TKIP. Another widely-
supported method is AES.
WPA2-PSK
This is a later version of WPA (WPA-PSK). The major change is the use of AES
(Advanced Encryption System) for protecting data. AES is very secure, considered to
be unbreakable. The PSK (Pre-shared Key) must be entered on each Wireless station.
If WPA2-PSK is used, the Wireless Stations and the Access Point must have the
same settings for each of the following:
Enter the same value on every station and the AP.
The PSK must be from 8 to 63 characters in length.
The 256Bit key used for the actual encryption is de-
rived from this key.
WPA2 PSK
(Pre-shared Key)
The same encryption method must be used. The most
common encryption method is TKIP. Another widely-
supported method is AES.
Encryption
Wireless LAN Configuration
To allow Wireless Stations to use the Access Point, the Wireless Stations and the
Access Point must use the same settings, as follows:
On client Wireless Stations, the mode must be set to "Infrastruc-
ture".
Mode
(The Access Point is always in "Infrastructure" mode.)
Most Wireless stations will set the correct mode automatically.
Wireless Stations should use the same SSID (ESSID) as the
Access Point they wish to connect to. Alternatively, the SSID can
be set to "any" or null (blank) to allow connection to any Access
Point.
SSID (ESSID)
Security
The Wireless Stations and the Access Point must use the same
settings for Wireless security. (Off, WEP, WPA-PSK, WPA2-PSK,
WPA-PSK+WPA2-PSK).
WEP: If WEP is used, the Key size (64Bit, 128Bit), Key value,
and Authentication settings must be the same on the Wireless
Stations and the Access Point.
WPA-PSK: If WPA-PSK is used, all Wireless Stations must be
set to use WPA-PSK, and have the same Pre-shared Key and
encryption system.
WPA2-PSK: If WPA2-PSK is used, all Wireless Stations must be
set to use WPA2-PSK, and have the same Pre-shared Key and
encryption system.
WPA-PSK +WPA2-PSK: If WPA-PSK +WPA2-PSK is used, all
Wireless Stations must be set to use WPA-PSK +WPA2-PSK, and
have the same Pre-shared Key and encryption system.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B - About Wireless LANs
For Ad-hoc networks (no Access Point), all Wireless stations
must use the same security settings.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
C
Specifications
Multi-Function Wireless Broadband router
Model
11g Wireless Broadband router, QoS
215mm(W) * 150mm(D) * 37mm(H)
0° C to 40° C
Dimensions
Operating Tempera-
ture
Storage Temperature
Network Protocol:
Network Interface:
-10° C to 70° C
TCP/IP
5 Ethernet:
4 * 10/100BaseT (RJ45) LAN connection
1 * 10/100BaseT (RJ45) for WAN
LEDs
8
Power Adapter
4.5V/1.5A DC External
Wireless Interface
Standards
Frequency
Channels
IEEE802.11g WLAN, JEIDA 4.2, roaming support
2.4 to 2.4835GHz (Industrial Scientific Medical Band )
Maximum 14 Channels, depending on regulatory authorities
DSSS BPSK/QPSK/CCK, OFDM/CCK
Up to 54 Mbps
Modulation
Data Rate
Coverage Area
Indoors : 15m @54Mbps, 120m @6Mbps or lower
Outdoors : 40m @54Mbps, 300m @6Mbps or lower
WEP
64-Bit, 128-Bit
PSK
WPA/WPA2
Output Power
13dBm (typical)
Receiver Sensitivity -80dBm Min.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C - Specifications
Regulatory Approvals
CE Standards
This product complies with the 99/5/EEC directives, including the following safety and
EMC standards:
•
•
•
EN300328-2
EN301489-1/-17
EN60950
CE Marking Warning
Hereby, Digital Data Communications, declares that this (Model-no. WBR-3408) is in
compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC.
The CE-Declaration of Conformity can be downloaded at:
http://www.levelone.eu/support.php
103
Download from Www.Somanuals.com. All Manuals Search And Download.
|