®
AM/FM RADIO CASSETTE RECORDER
MODEL CT-99
OPERATING INSTRUCTIONS
CASSETTE PLAYER/RECORDER
AM/FM RADIO RECEIVER
ONE-TOUCH CASSETTE RECORDING
AUTOMATIC LEVEL CONTROL
ROTARY VOLUME CONTROL
BUILT-IN CONDENSER MICROPHONE
AC/BATTERY OPERATION
FULL SIZE FOLDING HANDLE
•
•
•
•
•
•
•
•
PLEASE READ CAREFULLY BEFORE USE
CT-99021600 NL v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
14. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
15. Damage Requiring Service - The appliance should be serviced by qualified service
personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in
performance; or
E. The appliance has been dropped, or the enclosure damaged.
16. Servicing - The user should not attempt to service the appliance beyond that described
in the operating instructions. All other servicing should be referred to qualified service
personnel.
17. Power lines - An outdoor antenna should be located away from power lines.
18. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be
sure the antenna system is grounded so as to provide some protection against voltage
surges and built up static charges. Section 810 of the National Electrical Code, ANSI/
NFPA 70 provides information with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See Figure.
EXAMPLE OF ANTENNA GROUNDING AS PER
NEC - NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT (NEC
SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
It is the intent of Lenoxx that this product be used in full compliance with the copyright
laws of the United States and that prior permission be obtained from copyright owners
whenever recording songs from the radio.
Do not apply oil or petroleum products or solvents to any part of this set.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE TO YOUR
SET, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries mentioned in the operating instructions
booklet (batteries are not included with this set, please buy the proper batteries).
2. Do not dispose the batteries into a fire. The cells may explode. Check with local
codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
4. Be careful when handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may over
heat and cause burns.
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak
corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may cause burns or
irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and discharged
batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity (
and
) or
direction must be observed. Reverse insertion of some or all of the batteries may
result in battery eletrolyte leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long
period of time (several months or more) since during the period the batteries could
leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to
leak in the product. Batteries should be replaced (depending on the product) when
the display gets dim or if the Low Battery Indicator shows or if the sound gets
distorted.
11. Do not store this product in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be protected
from condensation during storage and defrosting. Batteries should be stabilized at
room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING in this manual.
If you can’t resolve the problem, or if the product is damaged, refer to the LENOXX
WARRANTY INFORMATION. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock
when the appliance is subsequently used.
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch
your skin, and discard the leaking batteries.
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).
15. The use of rechargeable batteries is not recommended for this set because their
voltage and life is lower than standard batteries.
16. Installation of batteries should be done by an adult only.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING THE POWER SOURCES
You can use the AC power or batteries as a power source.
2. Battery compartment
1. To a wall outlet
NOTE: One blade of plug &
outlet is wider.
1.Connecting the AC Power
Cord
TIP
Open the BATTERY COMPARTMENT DOOR, stretch the
AC power cord out, and insert the AC PLUG into the wall
outlet.
The plug of the AC power
cord is polarized and only
fits one way into the wall
outlet.
If this plug does not
match your outlet, do not
force it.
2.Operate the Set on Batteries
Insert 4 size “D” batteries (not included) into the battery
compartment.
Reverse it and try again.
D
D
D
D
BACK OF SET
4
Download from Www.Somanuals.com. All Manuals Search And Download.
LISTENING TO THE RADIO
3
2
1&4
Connect the supplied AC power cord or batteries (see page 4).
Slide the FUNCTION SWITCH to AM
or FM position.
1
FM
TAPE
AM
RADIO OFF
TUNING
Tune into the station you prefer using
the TUNING control. Adjust for the
clearest sound.
2
3
VOLUME
Adjust the volume level by rotating the
VOLUME control.
MIN
MAX
To turn off the Radio, slide the
FUNCTION switch to TAPE (RADIO
OFF) position.
4
FM
TAPE
AM
RADIO OFF
TIP:To improve broadcast reception, change position of the
antenna for FM and rotate the player itself for AM.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A TAPE
1
3
2
Connect the supplied AC power cord or batteries (see page 9).
Slide the FUNCTION
switch to TAPE (POWER
OFF) position.
1
FM
TAPE
AM
RADIO OFF
Press the STOP/EJECT
button to open the tape
compartment and insert
a recorded tape. Close
the door.
EMPTY
REEL
FULL
REEL
2
STOP/EJ.
INSERT TAPE THIS WAY
FULL REEL ON RIGHT
Press the PLAY button.
The player turns on and
starts playing.
3
PLAY
6
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
VOLUME
CONTROL
PAUSE
FAST FORWARD
& REWIND
PLAY
STOP/EJ.
TIP
To
Press or Adjust
VOLUME control
When the tape finishes
Adjust the volume
Stop playback
playing that side of the
tape, the set will stop and
the PLAY button will pop
up. To hear the other
side, flip the tape over,
then insert and press
PLAY, or press REWIND
then PLAY to hear the
same song again.
STOP/EJECT button
Fast forward or rewind
the tape
FAST FORWARD button
or REWIND button
Pause playback
PAUSE button
Press again to resume
play after pause.
Eject the cassette
STOP/EJECT button
To enjoy the music without
disturbing others
Insert your headphone
plug into the mono
EARPHONE jack
MONO EARPHONE JACK
NOTE: If you use stereo headphones, you will only hear
sound from one side of the headphones because
this jack is mono.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING ON A TAPE
MICROPHONE
2
3
1
Connect the supplied AC power cord or batteries (see page 4).
1
2
Press the STOP/EJECT button
to open the tape compartment
and insert a blank tape. Select
the program source (AM, FM
or built-in microphone) you
want to record.
INSERT TAPE THIS WAY
FULL REEL ON RIGHT
STOP/EJ.
To record from radio, slide the
FUNCTION switch to AM or FM
position, and tune into the station
you want (see page 5).
FM
TAPE
AM
RADIO OFF
To record from the built-in
microphone, leave the FUNCTION
switch at TAPE position, and speak
in front of the set.
FM
TAPE
AM
RADIO OFF
Press the RECORD button to start
recording. (The PLAY button is
depressed automatically.)
3
RECORD
8
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
FUNCTION
SWITCH
TIP
• Adjusting the
VOLUME control
will not affect the
recording level.
PAUSE
STOP/EJECT
• For best recording
effect, use AC power
instead of batteries.
To
Press or Adjust
Stop recording
STOP/EJECT button
Pause recording
PAUSE button
Press the button again to
resume recording.
• To erase a recording,
just start a new one,
and the old recording
is automatically
Turn off the power
Press the STOP/EJECT button
and slide the FUNCTION
switch to TAPE (RADIO OFF)
position.
replaced.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
On Safety
Notes on Cassettes
Should any solid object or liquid fall
Break off the cassette tab from side A
•
•
into the set, disconnect the power, and
have it checked by qualified personnel
before operating it any further.
or B to prevent accidental recording.
If you want to reuse the tape for
recording, cover the broken tab with
adhesive tape.
On Placement
Side A
Do not leave the set in a location
•
near heat source, or in a place subject
to direct sunlight, excessive dust or
mechanical shock.
Do not place the set on an inclined
or unstable place.
•
Tab for side A
Tab for side B
Do not place anything within 1 inch of
•
the back of the cabinet. The ventilation
holes must be unobstructed for the
set to operate properly and prolong
the life of its components.
To record on a tape with its tab broken
off, cover the respective tab hole for side
A or B with adhesive tape.
•
If the set is left in a car parked in
•
The use of a cassette with more than 90
the sun, be sure to choose a location
in the car where the set will not be
subjected to the direct rays of the sun.
•
minutes of play time is not recommended
except for long continuous recording or
playback.
Since a strong magnet is used for the
•
speakers, keep personal credit cards
using magnetic coding or spring-
wound watches away from the set
to prevent possible damage from the
magnet.
To reduce the chances of tape jamming
•
or tangling, you should check that there
are no loose layers of tape visible
through the cassette center window. If
any, tighten these loose layers of tape
using a pencil before inserting the
cassette into the set.
On Power Sources
For battery operation, use 4 size “D”
batteries. We recommend alkaline
batteries for longer life.
•
When the batteries are not to be used,
•
remove them to avoid damage that can
be caused by battery leakage or
corrosion.
The nameplate indicating operating
voltage, power consumption, etc. is
located at the back of the set.
•
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Cleaning the Tape Heads
Wipe the heads, the pinch roller and the capstan with a cleaning swab slightly moistened
with cleaning fluid or alcohol after every 10 hours of operation for optimum playback
and recording quality.
After cleaning, insert a tape when the areas cleaned are completely dry.
Cotton swab
Capstan
NOTE: In order to see and
clean the head, you
may have to press
PLAY first.
Erase head
Pinch roller
Notes for Storing Cassette Tapes
1. Do not put a tape near a magnetic field, such as a TV, or speaker. Magnetic
fields may reduce the tape sensitivity or even erase the recording.
2. Do not store tape for any length of time in a hot, moist or dusty place.
Cleaning the Cabinet
Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent,
such as alcohol or benzene.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Remedy
Connect the AC power cord to a wall
outlet securely.
•
The power is not on.
Make sure the batteries are inserted
correctly and they are fresh.
•
Make sure the FUNCTION switch is in
the correct position.
•
There is no sound.
Adjust the volume.
Unplug the headphones when listening
through speakers.
•
•
Replace all the batteries with fresh ones if
•
The sound is weak or of poor
quality.
they are weak, or bring the set near a
window, or rotate the set (for AM) or adjust
the FM antenna for best FM reception.
Make sure the safety tab on the cassette
is in place.
Make sure the FUNCTION switch is at
TAPE position.
The RECORD button does not
function / The tape does not
play.
•
•
Clean the erasing head (see page 11).
Replace all the batteries with fresh ones if
they are weak.
The tape does not erase
completely.
•
•
Make sure the tape is inserted properly.
Make sure the cassette tab is in place.
The tape does not record.
•
•
Clean the heads, pinch roller and capstan
(see page 11).
The sound is weak / The sound
quality is poor.
•
The tape has reached its end. Remove it,
flip to the other side, re-insert and press
PLAY.
•
Cassette PLAY button pops up.
NOTE: Normal battery life using alkaline batteries is about 8 hours of playing time.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND A CLOTH OR OTHER PROTECTIVE MATERIAL BE PLACED UNDER
THE SET WHEN PLACING IT ON SURFACE WITH A NATURAL OR LACQUER FINISH.
For Customer Service Dial 1-800-315-5885
(MONDAY - THURSDAY 09:00 AM - 5:00 PM, FRIDAY 09:00 AM - 1:00 PM EST)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATION
General Description
AC 120V, 60Hz 4 Watts
DC 6V (4 size “D” batteries)
Power source:
(we recommend alkaline batteries for longer life)
Speakers:
3” DYNAMIC
Output power:
Dimensions:
600mW
1
Width: 12 / ”
Depth: 5 / ”
Height: 6 / ”
Weight: 3 LBs (without batteries)
4
3
4
1
2
Tape Recorder Section
Tape:
Standard normal bias cassette tape
Frequency response: 125 - 8000 Hz
Wow & flutter:
0.35% W.R.M.S.
Radio Section
Frequency range:
FM: 88 - 108 MHz
AM: 530 - 1700 KHz
LENOXX reserves the right to make design and specification changes for product
improvement.
LIMITED WARRANTY
We warrant this product to be free from defects in material and workmanship under normal use for a period
of 90 days after purchase and we will repair it free of charge or replace it at no charge, should it become defective
under this warranty, providing you submit proof of purchase (sales slip) with the set.
During the initial 90 day period after original purchase, we will service or exchange, at no charge, the set that
is returned to LENOXX ELECTRONICS CORP. (LENOXX will pay the shipping back to you). After the initial
90 days period expires, and for a period of 12 months from original purchase we will repair the unit covering any
part(s) that need to be replaced at no charge, but will charge for the cost of labor, return postage paid by Lenoxx.
This warranty does not apply to any product which has been subject to misuse,
neglect or accident. This warranty does not cover a broken cabinet. UNDER NO CIRCUMSTANCES WILL
LENOXX ELECTRONICS CORP. BE LIABLE FOR ANY INCIDENTALOR CONSEQUENTIALDAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state. The following charges apply to repairs beyond the warranty period: $7.00. Be sure to pack carefully and
return postage paid insured together with your money order (personal checks will not be accepted) and sales
receipt to:
LENOXX ELECTRONICS CORP., 2 GERMAK DRIVE, CARTERET, N.J. 07008
© 2000 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|