COMPACT DISC PLAYER
WITH AM/FM RADIO
MODEL CD-1095
OPERATING INSTRUCTIONS
PLAYS MUSIC COMPACT DISCS
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT PLAY
RECEIVES AM/FM BROADCASTS
POWER LED INDICATOR
2 WAY POWER - AC/DC
REQUIRES 6 SIZE “C” BATTERIES (not included)
•
•
•
•
•
•
PLEASE READ CAREFULLY BEFORE USE
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL SAFETY INSTRUCTIONS
1. Power Sources - The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
2. Wall or Ceiling Mounting - The appliance should not be mounted to a wall or ceiling.
3. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
4. Servicing - The user should not attempt to service the appliance beyond that described in
the operating instructions. All other servicing should be referred to qualified service personnel.
Do not apply oil or petroleum products or solvents to any part of this set.
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated
at the back of the set.
2
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE TO YOUR
SET, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries mentioned in the operating instructions
booklet (batteries are not included with this set, please buy the proper batteries).
2. Do not dispose the batteries into a fire. The cells may explode. Check with local
codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
4. Be careful when handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may over
heat and cause burns.
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak
corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may cause burns or
irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and discharged
batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity (
and
) or
direction must be observed. Reverse insertion of some or all of the batteries may
result in battery electrolyte leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long
period of time (several months or more) since during the period the batteries could
leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to
leak in the product. Batteries should be replaced (depending on the product) when
the display gets dim or if the Low Battery Indicator shows or if the sound gets
distorted.
11. Do not store this product in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be protected
from condensation during storage and defrosting. Batteries should be stabilized at
room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING in this instruction
manual. If you can’t resolve the problem, or if the product is damaged, refer to the
LENOXX WARRANTY INFORMATION. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock when
the appliance is subsequently used.
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch your skin,
and discard the leaking batteries.
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).
15. The use of rechargeable batteries is not recommended for this set because their
voltage and life is lower than standard batteries.
16. Installation of batteries should be done by an adult only.
SAVE THESE INSTRUCTIONS
3
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING THE POWER SOURCES
You can use the AC power or batteries as a power source.
To a wall outlet
NOTE: One blade of the
plug and outlet is wider.
AC SOCKET
Replace the batteries
when the POWER lamp
dims or when the player
stops operating. Replace
all the batteries with new
ones. Before you replace
the batteries, be sure to
take out the CD from the
player and remember to
check the Battery Safety
Instructions on Page 3.
•
1. Connecting the AC power
cord
Insert one end of the supplied AC power cord into
the socket located at the rear of the player, and the
o2t.heUr esnidntogthtehwealpl olautlyete. r on batteries
Insert 6 size “C” batteries (not supplied) into the
battery compartment.
To use the player on batteries, disconnect and
remove the AC power cord both from back of the
player and the wall outlet.
If the CD does not play
on batteries, this means
the batteries are almost
used up. But the radio
may continue to play on
these weak batteries
because it uses less
power than the CD player.
•
Insert new batteries as
shown.
4
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A CD
OPEN THE CD DOOR
BY LIFTING HERE
FUNCTION SWITCH
(at the left side of the set)
PLAY/PAUSE
Connect the supplied AC power cord or batteries (see page 4).
Slide the FUNCTION switch
FUNCTION
RADIO OFF
CD
(at the left side of the set) to
CD position, the POWER lamp
will turn on and the display will
show 2 dashes “--” flashing,
1
2
3
POWER lamp
then “
”.
Lift the right corner of the CD
DOOR to open it and place a
CD in the CD compartment.
The label side of the CD
should face upward.
Close the CD DOOR by
pushing it down. The display
will show the total tracks of
that CD.
Press the PLAY/PAUSE
button. The PLAY/PAUSE
lamp will be steadily on, the
player will play all the tracks
in order once.
4
Track
PLAY/PAUSE
lamp
number
5
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
VOLUME
CONTROL
OPEN THE CD DOOR
BY LIFTING HERE
PHONES
JACK
FUNCTION SWITCH
(at the left side of the set)
STOP
BACKWARD
PLAY/PAUSE
FORWARD
TIP
When CD play is
paused, the PLAY/
PAUSE lamp will
flash and no music
will play.
To
Press or Adjust
VOLUME control
STOP
Adjust the volume
Stop playback
PLAY/PAUSE
To resume play,
press the PLAY/
The PLAY/PAUSE lamp will
flash during pause. Press
again to resume play after
pause.
Pause playback
PAUSE
button
again, the PLAY/
PAUSE lamp will
stop flashing and
music will play.
Go to the next track
FORWARDS
BACKWARDS
Go back to the previous
track
TIP
If you bump the set
during CD play, the
music will stop or
BACKWARDS
FORWARDS
or
, press
Locate a point in a song
and hold down while playing
until you find the point.
skip for
a
few
seconds. This is
normal for this type
of player.
Insert your headphones (not
included) plug into the
PHONES jack (at the left side
of the set).
To enjoy the music
without disturbing others
Lift the right corner of the CD
DOOR (press STOP first).
Remove the CD
Slide the FUNCTION switch
(at the left side of the set) to
OFF position.
Turn off the power
6
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING CD TRACKS REPEATEDLY
(REPEAT PLAY)
You can play CD tracks over and over in normal or programmed play modes (see
page 8).
PLAY/PAUSE
FUNCTION SWITCH
(at the left side of the set)
REPEAT
BUTTON
PROGRAM BUTTON
FORWARD
BACKWARD
1. Slide the FUNCTION switch (at the left side of the set) to the CD position.
2. Select the track by pressing SKIP/SEARCH BACKWARD or FORWARD
, and then press ..
3. Press the CD REPEAT button.
To repeat
Press
Display shows
REPEAT
Press the REPEAT button
once, the REPEAT lamp will be
flashing.
a single track (song)
PROGRAM
PLAY/
PAUSE
REPEAT
Press the REPEAT button
twice, the REPEAT lamp will be
steadily on.
PROGRAM
all the tracks (all songs)
programmed tracks
PLAY/
PAUSE
During programmed play, press
the REPEAT button twice, the
REPEAT
PROGRAM
REPEAT
lamp
and
the
PLAY/
PROGRAM lamp will be steadily
on.
PAUSE
To cancel Repeat Play
Press the REPEAT button until the REPEAT lamp goes off.
7
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTING YOUR OWN MUSIC PLAYING ORDER
(Programmed Play)
You can make a program of up to 20 tracks in the order you want them to be
played.
PROGRAM
BUTTON
PROGRAM LAMP
1. Slide the FUNCTION switch to CD position.
REPEAT
Make sure the CD is stopped.
PROGRAM
2. Press the PROG. button. The letters
PLAY/
PAUSE
“
” and the PROGRAM lamp will flash in the
display.
3. Press
or
to select the tracks you want to
REPEAT
program in the order you want. The selected
number will be steadily on and the program lamp
will be flashing.
PROGRAM
PLAY/
PAUSE
4. Press the PROG. button to confirm. The letters
“
” and the PROGRAM lamp will flash in the
display for next selection.
REPEAT
5. Repeat steps 3 and 4. You can program up to 20
tracks until the display shows the tracks what you
PROGRAM
selected.
PLAY/
PAUSE
6. Press
to start programmed play. The PLAY/
PAUSE lamp and the PROGRAM lamp will be steadily
on.
To change the current program
Just create a new program following the programming procedure.
To cancel Programmed Play
Slide the FUNCTION switch to OFF position.
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
8
LISTENING TO THE RADIO
FUNCTION SWITCH
(at the left side of the set)
TUNING CONTROL
BAND SWITCH
Connect the supplied AC power cord or batteries (see page 4).
FUNCTION
RADIO OFF
CD
Slide the FUNCTION switch (at the
left side of the set) to RADIO
position, the POWER lamp will turn
on.
1
2
BAND
AM
FM
Slide the BAND switch (at the right
side of the set) to the proper band
position (AM or FM) that you want.
Tune into the station you prefer
using the TUNING control. Adjust
for the clearest sound.
3
9
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
VOLUME CONTROL
FUNCTION SWITCH
(at the left side of the set)
TIP
To
Slide or Adjust
Next time you want to
•
listen to the radio, just
slide the FUNCTION
Adjust the volume
VOLUME control
switch
to
RADIO
Slide the FUNCTION switch
(at the left side of the set)
to OFF position
position. The player
automatically starts
playing the previously
tuned station.
Turn off the Radio
To improve broadcast reception
Change position of the antenna for FM. Move the set
itself for AM.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
IB-CD1095(SY)-WM-E-031604
PRECAUTIONS
On Safety
On Power Sources
As the laser beam used in the CD
For battery operation, use 6 size “C”
•
•
player section may be harmful to the
eyes, do not attempt to disassemble
the cabinet. Refer servicing to
qualified personnel only.
batteries. We recommend alkaline
batteries for longer life.
When the batteries will not be used
•
for a few weeks or more, remove them
to avoid damage that can be caused
by battery leakage or corrosion.
Should any solid object or liquid fall
•
into the player, unplug the player, and
have it checked by qualified personnel
before operating it any further.
On Operation
On Placement
If the player is brought directly from a
•
Do not leave the player in a location
•
cold to a warm location, or is placed
in a very damp room, moisture may
condense on the lens inside the CD
player section. Should this occur, the
player will not operate properly. In
this case, remove the CD and wait
about an hour for the moisture to
evaporate.
near a heat source, or in a place
subject to direct sunlight, excessive
dust or mechanical shock.
Do not place the player on an inclined
or unstable place.
•
Do not place anything within 1 inch of
•
the back of the cabinet. The
ventilation holes must not be covered
for the player to operate properly and
prolong the life of its components.
This CD player is designed to be
•
played on
a
stable no vibration
position. If you bump the set during
CD play, the music will stop or skip for
a few seconds. This is normal for this
type of player.
If the player is left in a car parked in
•
the sun, be sure to choose a location
in the car where the player will not be
subjected to the direct rays of the
sun.
Since a strong magnet is used for the
•
speakers, keep personal credit cards
using magnetic coding or springwound
watches away from the player to
prevent possible damage from the
magnets.
11
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS (continued)
Notes on CDs
cleaning cloth. Wipe the CD from the
center out.
MAINTENANCE
Cleaning the Lens
If the lens becomes dirty, it may
cause a skipping of sound during CD
operation. Clean with a commercially
available lens cleaner and blower.
Before playing, clean the CD with a
•
Do not use solvents such as benzine,
•
thinner, commercially available cleaners
or anti-static spray intended for vinyl
LPs.
Do not expose the CD to direct
•
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature inside
the car.
Cleaning the Cabinet
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder, or solvent, such as alcohol or
benzine.
Do not stick paper or stickers on the
•
CD, nor scratch the CD.
After playing, store the CD in its case.
•
If there is a scratch, dirt or fingerprints
on the CD, it may cause a tracking
error or skipping.
12
IB-CD1095(SY)-WM-E-031604
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Remedy
Problem
Connect the AC power cord to a wall
outlet securely.
•
The power is not on.
Make sure the batteries are inserted
correctly and they are fresh.
•
Make sure the FUNCTION switch is at
the right position as you want.
Adjust the volume.
Unplug the headphones when listening
through speakers.
•
•
•
There is no sound.
“
” appears in the display
Insert the CD with the label side up.
•
•
•
•
•
even when a CD is in place.
Make sure that the CD compartment is
closed.
Place the CD with the label side up.
Clean the CD.
Take out the CD and leave the CD DOOR
open for about an hour to dry moisture
condensation.
Make sure the FUNCTION switch is at CD
position.
CD does not play.
•
Clean the CD, or replace it if the CD is
badly damaged.
•
•
The sound drops out.
Place the player in a location free from
vibration.
Check if your batteries are fresh.
•
CD does not play while radio
may continue to play.
It is normal since the radio uses less power
than the CD player.
•
Replace all the batteries with new ones if
they are weak, or bring the set near a
window, or rotate the set.
•
The sound is weak or has
poor quality.
IB-CD1095(SY)-WM-E-031604
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATION
General Description
Power source:
AC 120V, 60Hz, 14Watts
DC 9V (6 size “C” batteries)
(Alkaline batteries are recommended)
Speakers:
2 - 3 ” 8 ohm
Output power:
Dimensions:
1.5W/channel
Width: 12”
Depth: 10”
Height: 6”
Weight: 3.3LBs (without batteries)
CD Section
Any normal CD used in portable players
760 - 800 NM
3 - spot error detection
50Hz - 15kHz +1/-2dB
Plays disc type:
Laser wavelength:
Tracking method:
Frequency response:
3.86 mm lens
NOTE: This CD player will only play NORMAL music CDs (or CD-R CDs).
This set will not play CD-RW encoded discs.
Radio Section
Frequency range:
FM: 88 - 108 MHz
AM: 530 - 1700 kHz
LENOXX reserves the right to make design and specification changes for
product improvement.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND A CLOTH OR OTHER PROTECTIVE MATERIAL BE PLACED
UNDER THE SET WHEN PLACING IT ON SURFACE WITH A NATURAL OR
LACQUER FINISH.
IB-CD1095(SY)-WM-E-031604
14
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
We warrant this product to be free from defects in material and workmanship
under normal use for a period of 90 days after purchase and we will repair it free
of charge or replace it at no charge, should it become defective under this
warranty, providing you submit proof of purchase (sales slip) with the set.
During the initial 90 day period after original purchase, we will service or exchange,
at no charge, the set that is returned to LENOXX ELECTRONICS CORP. After the
initial 90 day period expires, and for a period of 12 months from original purchase,
we will repair the unit covering any part(s) that need to be replaced at no charge, but
will charge for the cost of labor, return postage paid by Lenoxx.
This warranty does not apply to any products which have been subject to
misuse, neglect or accident. This warranty does not cover broken cord or cabinet.
UNDER NO CIRCUMSTANCES WILL LENOXX ELECTRONICS CORP. BE LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. The following charges apply to repairs
beyond the warranty period: $10.00. Be sure to pack carefully and return postage
paid insured together with your money order (personal checks will not be accepted)
and sales receipt to:
LENOXX ELECTRONICS CORP., 2 GERMAK DRIVE, CARTERET N.J. 07008
For customer service dial 1-800-315-5885
© 2004 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
15
Download from Www.Somanuals.com. All Manuals Search And Download.
IB-CD1095(SY)-WM-E-031604
|