ThinkServer RS110 Types 6435, 6436, 6437, and 6438
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
ThinkServer RS110 Types 6435, 6436, 6437, and 6438
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 61
and the Warranty and Support Information document on the Lenovo ThinkServer Documentation DVD.
First Edition (October 2008)
© Copyright Lenovo 2008.
Portions © Copyright International Business Machines Corporation 2008.
All rights reserved.
LENOVO products, data, computer software, and services have been developed exclusively at private expense and
are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights
to use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered
pursuant a General Services Administration ″GSA″ contract, use, reproduction, or disclosure is subject to restrictions
set forth in Contract No. GS-35F-05925.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
© Lenovo 2008. Portions © IBM Corp. 2008.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
© Lenovo 2008. Portions © IBM Corp. 2008.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Important:
Each caution and danger statement in this document is labeled with a number. This
number is used to cross reference an English-language caution or danger
statement with translated versions of the caution or danger statement in the Safety
Information document.
For example, if a caution statement is labeled “Statement 1,” translations for that
caution statement are in the Safety Information document under “Statement 1.”
Be sure to read all caution and danger statements in this document before you
perform the procedures. Read any additional safety information that comes with the
server or optional device before you install the device.
vi ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 1:
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
v Connect all power cords to a properly wired and grounded electrical
outlet.
v Connect to properly wired outlets any equipment that will be attached to
this product.
v When possible, use one hand only to connect or disconnect signal
cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached
devices.
To Connect:
To Disconnect:
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Safety vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 2:
CAUTION:
When replacing the lithium battery, use only the battery recommended by the
manufacturer. If your system has a module containing a lithium battery,
replace it only with the same module type made by the same manufacturer.
The battery contains lithium and can explode if not properly used, handled, or
disposed of.
Do not:
v Throw or immerse into water
v Heat to more than 100°C (212°F)
v Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
viii ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 3:
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
v Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
v Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
`
Appareil A Laser de Classe 1
Safety ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 4:
≥ 18 kg (39.7 lb)
≥ 32 kg (70.5 lb)
≥ 55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
2
1
x
ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 8:
CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect a problem with one of these parts, contact
a service technician.
Statement 26:
CAUTION:
Do not place any object on top of rack-mounted devices.
This server is suitable for use on an IT power-distribution system whose maximum
phase-to-phase voltage is 240 V under any distribution fault condition.
Safety xi
Download from Www.Somanuals.com. All Manuals Search And Download.
xii ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Introduction
This Installation Guide contains instructions for setting up your Lenovo®
ThinkServer™ RS110 Types 6435, 6436, 6437, and 6438 server and basic
instructions for installing some optional devices. More detailed instructions for
installing optional devices are in the User Guide on the Lenovo ThinkServer
Documentation DVD, which comes with the server. This document contains
information about:
v Setting up and cabling the server
v Starting and configuring the server
v Installing some optional devices
v Solving problems
If firmware and documentation updates are available, you can download them from
the Lenovo Web site. The server might have features that are not described in the
documentation that comes with the server, and the documentation might be updated
occasionally to include information about those features, or technical updates might
be available to provide additional information that is not included in the server
documentation. To check for updates, complete the following steps:
Note: Changes are made periodically to the Lenovo Support Web site. The actual
procedure might vary slightly from what is described in this document.
2. Enter your product number (machine type and model number) or select Servers
from the Select your product list.
3. Select Servers from the Brand list.
4. From Family list, select ThinkServer RS110, and click Continue.
The server comes with an EasyStartup DVD to help you configure the hardware,
install device drivers, and install the operating system.
The server comes with a limited warranty. You can obtain up-to-date information
about the server and other Lenovor products at http://www.lenovo.com/thinkserver.
Record information about the server in the following table. You will need this
information when you register the server with Lenovo.
Product name
ThinkServer RS110
Machine type
Model number
Serial number
Key serial number
Key manufacturer
Key phone number
ThinkServer RS110, Types 6435, 6436, 6437 and 6438
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
The model number and serial number are on the ID label on the bezel, as shown in
the following illustration.
© Lenovo 2008. Portions © IBM Corp. 2008.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
ID label
Note: This illustration shows a serial-attached SCSI (SAS) hot-swap hard disk drive
model (3.5-inch drives). A Serial ATA (SATA) hot-swap hard disk drive model
(3.5-inch drives), SATA simple-swap hard disk drive model (3.5-inch drives), and a
SAS hot-swap model with 2.5-inch hard disk drives are also available. This
illustration might differ slightly from your hardware.
For a list of supported optional devices for the server, see http://www.lenovo.com/
See the Rack Installation Instructions document for complete rack installation and
removal instructions.
The Lenovo ThinkServer Documentation DVD
The Lenovo ThinkServer Documentation DVD contains documentation for the
server in Portable Document Format (PDF).
Hardware and software requirements
The Lenovo ThinkServer Documentation DVD requires the following minimum
hardware and software:
v Microsoft® Windows® XP, Windows 2000, or Red Hat Linux
v 100 MHz microprocessor
v 32 MB of RAM
v Adobe® Acrobat® Reader 3.0 (or later) or xpdf, which comes with Linux operating
systems
Notices and statements in this document
The caution and danger statements in this document are also in the multilingual
Safety Information document, which is on the Lenovo ThinkServer Documentation
DVD. Each statement is numbered for reference to the corresponding statement in
the Safety Information document.
The following notices and statements are used in this document:
v Note: These notices provide important tips, guidance, or advice.
v Important: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
2
ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
v Attention: These notices indicate potential damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in which
damage might occur.
v Caution: These statements indicate situations that can be potentially hazardous
to you. A caution statement is placed just before the description of a potentially
hazardous procedure step or situation.
v Danger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
Features and specifications
The following information is a summary of the features and specifications of the
server. Depending on the server model, some features might not be available, or
some specifications might not apply.
Racks are marked in vertical increments of 4.45 cm (1.75 inches). Each increment
is referred to as a unit, or “U.” A 1-U-high device is 1.75 inches tall.
Chapter 1. Introduction
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 1. Features and specifications
Microprocessor:
Expansion slots:
Acoustical noise emissions:
v Sound power, idling: 6.5 bel
maximum
One Intel® LGA 775 single core, dual Two PCI Express x8 slots, one
core, or quad core, depending on the low-profile and one 3/4-length full
server model:
height. Low-profile slot supports x4
electrical.
v Sound power, operating: 6.5 bel
v Single core: Celeron 440 or later
v Dual core: Core 2 Duo E4600 or
Xeon E3110, or later
v Quad core: Xeon 3300 series
maximum
Video controller:
Heat output:
v ATI ES1000 video on system
Approximate heat output in British
thermal units (Btu) per hour:
v Minimum configuration: 341 Btu per
hour (100 watts)
board
Notes:
v 16 MB DDR II video memory
1. Use the Configuration/Setup Utility
program to determine the size of
the L2 cache, type and speed of
the microprocessor, and speed of
the front-side bus.
Power supply:
351 watt (110 or 220 V ac
auto-sensing)
v Maximum configuration: 1024 Btu
per hour (300 watts)
Electrical input:
Size:
v Sine-wave input (50 - 60 Hz)
2. Intel Virtualization Technology (VT)
is not available on the Celeron
440 or the Core 2 Duo E4600;
however, these microprocessors
can run paravirtualization.
v Height: 43 mm (1.75 inches, 1 U)
v Depth: 559 mm (22 inches)
v Width: 440 mm (17.32 inches)
v Maximum weight: 12.7 kg (28 lb)
depending on your configuration
required
v Input voltage low range:
– Minimum: 100 V ac
– Maximum: 127 V ac
v Input voltage high range:
– Minimum: 200 V ac
– Maximum: 240 V ac
v Approximate input kilovolt-amperes
(kVA):
Memory:
Integrated functions:
v Minimum: Two 512 MB DIMMs
v Two Broadcom NetXtreme™ GB
Ethernet controllers on the system
board with Wake on LAN® support
v Serial port
v Maximum: 8 GB
v Type: PC2-5300, 667 MHz, ECC,
DDR II unbuffered SDRAM DIMMs
v Slots: Four dual inline
v Supports 512 MB, 1 GB, and 2 GB
DIMMs
– Minimum: 0.102 kVA
– Maximum: 0.55 kVA
v Four USB ports (two on front and
two on rear of server)
Notes:
1. Power consumption and heat
output vary depending on the
number and type of optional
v Systems-management port if an
optional Remote Supervisor
Adapter II SlimLine is installed
Drives:
Ultrabay Enhanced: CD or CD/DVD
features that are installed and the
power-management optional
features that are in use.
Hard disk controllers:
Expansion bays:
One of the following configurations:
v Serial ATA (SATA) controller
(simple-swap SATA models)
v Serial-attached SCSI (SAS)
controller with integrated RAID
(hot-swap SAS/SATA models) that
supports RAID levels 0, 1, 1E
2. These levels were measured in
controlled acoustical environments
according to the procedures that
are specified by the American
National Standards Institute (ANSI)
S12.10 and ISO 7779 and are
reported in accordance with ISO
9296. Actual sound-pressure levels
in a given location might exceed
the average stated values because
of room reflections and other
nearby noise sources. The declared
sound-power levels indicate an
upper limit, below which a large
number of computers will operate.
3. There is no keyboard connector or
mouse connector on the server.
You can connect a USB keyboard
and USB mouse to the server by
using the USB connectors.
v Two 3.5-inch slim-high bays for
hard disk drives.
– Hot-swap models: Supports
maximum of two serial-attached
SCSI (SAS) drives or two serial
ATA (SATA) drives.
– Simple-swap models: Supports
maximum of two SATA drives
Environment:
v Air temperature:
– Server on: 10° to 35°C (50.0°
to 95.0°F); altitude: 0 to 914.4
m (3000 ft)
v Four 2.5-inch small form-factor
(SFF) hot-swap bays for hard disk
drives. Supports a maximum of four
2.5-inch SAS drives.
– Server on: 10° to 32°C (50.0°
to 89.6°F); altitude: 914.4 m
(3000 ft) to 2133.6 m (7000 ft)
– Server off: 10° to 43°C (50.0°
to 109.4°F); maximum altitude:
2133.6 m (7000 ft)
– Shipping: -40° to 60°C
(-40° to 140°F); maximum
altitude: 2133.6 m (7000 ft)
v Humidity:
– Server on: 8% to 80%
– Server off: 8% to 80%
4
ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Major components of the server
Blue on a component indicates touch points, where you can grip the component to
remove it from or install it in the server, open or close a latch, and so on.
Orange on a component or an orange label on or near a component indicates that
the component can be hot-swapped, which means that if the server and operating
system support hot-swap capability, you can remove or install the component while
the server is running. (Orange can also indicate touch points on hot-swap
components.) See the instructions for removing or installing a specific hot-swap
component for any additional procedures that you might have to perform before you
remove or install the component.
The following illustration shows the major components in the server.
Note: The illustrations in this document might differ slightly from your hardware.
Chapter 1. Introduction
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3.5-inch models
ꢀ1ꢁ
ꢀ2ꢁ
Riser card assembly
SAS/SATA controller (some models)
ꢀ12ꢁ Bezel
ꢀ13ꢁ 3.5-inch hot-swap hard disk drive
(some models)
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
System board
ꢀ14ꢁ CD/DVD drive
SAS/SATA backplane (some models) ꢀ15ꢁ Operator information panel assembly
SATA simple-swap back panel (some ꢀ16ꢁ CD/DVD interface card
models)
ꢀ6ꢁ
ꢀ7ꢁ
ꢀ8ꢁ
Power supply
Fans
3.5-inch drive cage
ꢀ17ꢁ Fans
ꢀ18ꢁ Air baffle
ꢀ19ꢁ Microprocessor
6
ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ9ꢁ
3.5-inch simple-swap SATA hard disk ꢀ20ꢁ Heat-exchanger retention module
drive (some models)
ꢀ10ꢁ Simple-swap SATA filler panel
ꢀ21ꢁ Heat exchanger assembly
ꢀ11ꢁ Hot-swap hard disk drive filler
ꢀ22ꢁ DIMM
Chapter 1. Introduction
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5-inch models
ꢀ1ꢁ
ꢀ2ꢁ
Riser card assembly
SAS/SATA controller (some models)
ꢀ11ꢁ CD/DVD drive
ꢀ12ꢁ 3.5-inch hot-swap hard disk drive
(some models)
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
ꢀ6ꢁ
ꢀ7ꢁ
ꢀ8ꢁ
ꢀ9ꢁ
System board
2.5-inch hard disk drive backplane
Power supply
ꢀ13ꢁ Operator information panel assembly
ꢀ14ꢁ Fans
ꢀ15ꢁ Air baffle
Fans
ꢀ16ꢁ Microprocessor
2.5-inch drive cage
2.5-inch drive hard disk drive
2.5-inch filler panel
ꢀ17ꢁ Heat-exchanger retention module
ꢀ18ꢁ Heat-exchanger assembly
ꢀ19ꢁ DIMM
ꢀ10ꢁ Bezel
8
ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
System-board optional-device connectors
The following illustration shows the connectors for user-installable optional devices.
ꢀ1ꢁ
ꢀ2ꢁ
Other systems-management
connector
Remote Supervisor Adapter II
SlimLine connector
ꢀ6ꢁ
ꢀ7ꢁ
DIMM 3 connector
DIMM 2 connector
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
Battery connector
SAS/SATA controller connector
DIMM 4 connector
ꢀ8ꢁ
ꢀ9ꢁ
DIMM 1 connector
Riser card connector
The following illustration shows the locations of the PCI Express slots on the
riser-card assembly.
ꢀ1ꢁ PCI Express x8 slot 1
ꢀ2ꢁ PCI Express x8 slot 2
Chapter 1. Introduction
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installing optional devices
This chapter provides basic instructions for installing optional hardware devices in
the server. These instructions are intended for users who are experienced with
setting up Lenovo server hardware.
Installation guidelines
Before you install optional devices, read the following information:
“Handling static-sensitive devices” on page 13. This information will help you
work safely.
v When you install your new server, take the opportunity to download and apply
the most recent firmware updates. This step will help to ensure that any known
issues are addressed and that your server is ready to function at maximum levels
of performance. To download firmware updates for your server, complete the
following steps:
Note: Changes are made periodically to the Lenovo Web site. The actual
procedure might vary slightly from what is described in this document.
2. Enter your product number (machine type and model number) or select
Servers from the Select your product list.
3. Select Servers from the Brand list.
4. From Family list, select ThinkServer RS110, and click Continue.
5. Click Downloads and drivers to download firmware updates.
v Before you install optional hardware, make sure that the server is working
correctly. Start the server, and make sure that the operating system starts, if an
operating system is installed, or that a I9990305 error code is displayed,
indicating that an operating system was not found but the server is otherwise
working correctly. If the server is not working correctly, see Chapter 5, “Solving
problems,” on page 37 for diagnostic information.
v Observe good housekeeping in the area where you are working. Place removed
covers and other parts in a safe place.
v If you must start the server while the cover is removed, make sure that no one is
near the server and that no tools or other objects have been left inside the
server.
v Do not attempt to lift an object that you think is too heavy for you. If you have to
lift a heavy object, observe the following precautions:
– Make sure that you can stand safely without slipping.
– Distribute the weight of the object equally between your feet.
– Use a slow lifting force. Never move suddenly or twist when you lift a heavy
object.
– To avoid straining the muscles in your back, lift by standing or by pushing up
with your leg muscles.
v Make sure that you have an adequate number of properly grounded electrical
outlets for the server, monitor, and other devices.
v Back up all important data before you make changes to disk drives.
v Have a small flat-blade screwdriver available.
© Lenovo 2008. Portions © IBM Corp. 2008.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
v You do not have to turn off the server to install or replace hot-swap fans,
redundant hot-swap ac power supplies, or hot-plug Universal Serial Bus (USB)
devices. However, you must turn off the server before performing any steps that
involve removing or installing adapter cables or non-hot-swap optional devices or
components.
v Blue on a component indicates touch points, where you can grip the component
to remove it from or install it in the server, open or close a latch, and so on.
v Orange on a component or an orange label on or near a component indicates
that the component can be hot-swapped, which means that if the server and
operating system support hot-swap capability, you can remove or install the
component while the server is running. (Orange can also indicate touch points on
hot-swap components.) See the instructions for removing or installing a specific
hot-swap component for any additional procedures that you might have to
perform before you remove or install the component.
v When you are finished working on the server, reinstall all safety shields, guards,
labels, and ground wires.
System reliability guidelines
To help ensure proper cooling and system reliability, make sure that the following
requirements are met:
v Each of the drive bays has a drive or a filler panel and electromagnetic
compatibility (EMC) shield installed in it.
v If the server has redundant power, each of the power-supply bays has a power
supply installed in it.
v There is adequate space around the server to allow the server cooling system to
work properly. Leave approximately 50 mm (2.0 in.) of open space around the
front and rear of the server. Do not place objects in front of the fans. For proper
cooling and airflow, replace the server cover before you turn on the server.
Operating the server for extended periods of time (more than 30 minutes) with
the server cover removed might damage server components.
v You have followed the cabling instructions that come with optional adapters.
v You have replaced a failed fan within 48 hours.
v You have replaced a hot-swap drive within 2 minutes of removal.
v You do not operate the server without the air baffles installed. Operating the
server without the air baffles might cause the microprocessors to overheat.
Working inside the server with the power on
Attention: Static electricity that is released to internal server components when
the server is powered-on might cause the server to halt, which could result in the
loss of data. To avoid this potential problem, always use an electrostatic-discharge
wrist strap or other grounding system when you work inside the server with the
power on.
You might be instructed to turn on the server while the cover is off, to look at
system-board LEDs. Follow these guidelines when you work inside a server that is
turned on:
v Avoid wearing loose-fitting clothing on your forearms. Button long-sleeved shirts
before you work inside the server; do not wear cuff links while you are working
inside the server.
v Do not allow your necktie or scarf to hang inside the server.
12 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
v Remove jewelry, such as bracelets, necklaces, rings, and loose-fitting wrist
watches.
v Remove items from your shirt pocket, such as pens and pencils, that might fall
into the server as you lean over it.
v Avoid dropping any metallic objects, such as paper clips, hairpins, and screws,
into the server.
Handling static-sensitive devices
Attention: Static electricity can damage the server and other electronic devices.
To avoid damage, keep static-sensitive devices in their static-protective packages
until you are ready to install them.
To reduce the possibility of damage from electrostatic discharge, observe the
following precautions:
v Limit your movement. Movement can cause static electricity to build up around
you.
v The use of a grounding system is recommended. For example, wear an
electrostatic-discharge wrist strap, if one is available. Always use an
electrostatic-discharge wrist strap or other grounding system when you work
inside the server with the power on
v Handle the device carefully, holding it by its edges or its frame.
v Do not touch solder joints, pins, or exposed circuitry.
v Do not leave the device where others can handle and damage it.
v While the device is still in its static-protective package, touch it to an unpainted
metal surface on the outside of the server for at least 2 seconds. This drains
static electricity from the package and from your body.
v Remove the device from its package and install it directly into the server without
setting down the device. If it is necessary to set down the device, put it back into
its static-protective package. Do not place the device on the server cover or on a
metal surface.
v Take additional care when you handle devices during cold weather. Heating
reduces indoor humidity and increases static electricity.
Removing the cover
To remove the cover, complete the following steps:
2. Turn off the server and all attached devices.
3. Disconnect all external cables and power cords.
Chapter 2. Installing optional devices 13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press the cover-release button ꢀ1ꢁ.
5. Slide the cover back approximately 1.27 cm (0.5 inches); then, lift it off the
server.
Attention: For proper cooling and airflow, replace the cover before you turn on
the server. Operating the server for extended periods of time (more than 30
minutes) with the cover removed might damage server components.
Installing a memory module
The following notes describe the types of dual inline memory modules (DIMMs) that
the server supports and other information that you must consider when installing
DIMMs:
v The server supports 512 MB, 1 GB, and 2 GB DIMMs, for a maximum of 8 GB of
modules that you can use with the server.
v The amount of usable memory will be reduced depending on the system
configuration. A certain amount of memory must be reserved for system
resources. Use the system summary in the Configuration/Setup Utility program to
view the total amount of installed memory and the amount of configured memory
v The server comes with one 512 MB or 1 GB DIMM installed in DIMM connector
1 and an identical DIMM (the same size, speed, type, and technology) installed
in DIMM connector 3.
v If you install a pair of DIMMs in DIMM connectors 2 and 4, the size, speed, type,
and technology of the DIMMs that you install in DIMM connectors 2 and 4 must
match each other. However, they do not have to be the same size, speed, type,
and technology as the DIMMs that are installed in DIMM connectors 1 and 3.
v You can use compatible DIMMs from various manufacturers in the same pair.
v Install only double-data-rate II (DDR II), PC2-5300, unbuffered synchronous
dynamic random-access memory (SDRAM) with error correcting code (ECC)
DIMMs. These DIMMs must be compatible with the latest PC2-5300 SDRAM
unbuffered DIMM specification.
v If you install a pair of 2 GB DIMMs and a pair of other-size DIMMs, the 2 GB
DIMMs must be installed as the first pair (in DIMM connectors 1 and 3).
v When you restart the server after you add or remove a DIMM, a message is
displayed indicating that the memory configuration has changed.
14 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
To install a DIMM ꢀ1ꢁ or ꢀ2ꢁ, complete the following steps:
2. Turn off the server and peripheral devices, and disconnect the power cord and
all external cables. Remove the cover.
Attention: To avoid breaking the retaining clips or damaging the DIMM
connectors, open, and close the clips gently.
3. Open the retaining clip on each end of the DIMM connector.
4. Touch the static-protective package that contains the DIMM to any unpainted
metal surface on the outside of the server. Then, remove the DIMM from the
package.
5. Turn the DIMM so that the keys align correctly with the slot.
6. Insert the DIMM into the connector by aligning the edges of the DIMM with the
slots at each end of the DIMM connector. Firmly press the DIMM straight down
into the connector by applying pressure on both ends of the DIMM
simultaneously. The retaining clips snap into the locked position when the DIMM
is firmly seated in the connector. If there is a gap between the DIMM and the
retaining clips, the DIMM has not been correctly inserted; open the retaining
clips, remove the DIMM, and then reinsert it.
If you have other devices to install, do so now. Otherwise, go to “Completing the
Installing a hard disk drive
Locate the documentation that comes with the hard disk drive and follow those
instructions in addition to the instructions in this chapter.
Note: The ID for an installed hard disk drive is on the front of the server, next to
the bay that contains the drive.
Chapter 2. Installing optional devices 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2. Locations of hard disk drive IDs
3.5-inch drive model servers
2.5-inch drive model servers
Attention: To avoid damage to the hard disk drive connectors, make sure that the
cover is in place and fully closed whenever you install or remove a hard disk drive.
Installing a simple-swap Serial ATA hard disk drive
Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all
power from the server before you remove or install a simple-swap hard disk drive.
To install a simple-swap Serial ATA hard disk drive, complete the following steps.
Note: If you have only one hard disk drive, install it in the left drive bay.
ꢀ1ꢁ
ꢀ2ꢁ
SATA hard disk drive back plate
Filler panel
ꢀ3ꢁ
Hard disk drive assembly
Attention: To avoid damage to the hard disk drive connectors, make sure that the
cover is in place and fully closed whenever you install or remove a hard disk drive.
2. Make sure that the server cover is in place and fully closed.
3. Turn off the server and peripheral devices, and disconnect the power cord and
all external cables.
4. Remove the filler panel from the bay.
5. Pull the loops of the tray toward each other and slide the drive into the server
until the drive connects to the back panel.
16 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Insert the filler panel into the bay to cover the drive.
Notes:
1. If a RAID controller or adapter is installed, you might have to reconfigure the
disk arrays after you install hard disk drives. See your RAID controller or
adapter documentation.
2. To remove a simple-swap SATA drive from the bay, make sure that the server is
turned off and the power cord is removed; then, remove the filler panel, pull the
loops of the drive tray toward each other and pull the tray out of the bay.
If you have other devices to install, do so now. Otherwise, go to “Completing the
Installing a hot-swap hard disk drive
The 3.5-inch drive hot-swap server models support either two SAS 3.5-inch hard
disk drives or two SATA 3.5-inch hard disk drives. The 2.5-inch drive hot-swap
server models support four 2.5-inch SAS hard disk drives.
The installation procedure is the same for any of these drives. The illustrations in
this procedure show 3.5-inch SAS drives.
To install a hot-swap hard disk drive, complete the following steps.
Note: If you have only one hard disk drive, install it in the left or upper-left drive
bay.
Chapter 2. Installing optional devices 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention: To avoid damage to the hard disk drive connectors, make sure that the
cover is in place and fully closed whenever you install or remove a hard disk drive.
2. Make sure that the server cover is in place and fully closed.
3. Remove the filler panel ꢀ3ꢁ from the bay. Store it in a safe place for possible
future use.
Attention: To maintain proper system cooling, do not operate the server for
more than 10 minutes without either a drive or filler panel installed in each bay.
4. Open the drive tray handle ꢀ2ꢁ.
5. Gently push the drive assembly ꢀ1ꢁinto the bay until the drive stops.
6. Close the drive tray handle.
7. Check the hard disk drive status LED to make sure that the hard disk drive is
operating correctly. If the amber hard disk drive status LED for a drive is lit
continuously, that drive is faulty and must be replaced. If the green hard disk
drive activity LED is flashing, the drive is being accessed.
If you have other devices to install, do so now. Otherwise, go to “Completing the
Installing an adapter
The following notes describe the types of adapters that the server supports and
other information that you must consider when you install an adapter:
v Locate the documentation that comes with the adapter and follow those
instructions in addition to the instructions in this section. If you have to change
switch settings or jumper settings on the adapter, follow the instructions that
come with the adapter.
v The adapter slots are on the riser-card assembly. You must first remove the
riser-card assembly to access the adapter slots.
v The two PCI Express slots on the riser-card assembly support PCI Express x8
1.0a adapters.
v You can install one full-height three-quarter-length adapter in expansion slot 1
and one low-profile half-length adapter in expansion slot 2.
Note: When the optional Remote Supervisor Adapter II SlimLine is installed in
the server, you can install only a half-length adapter in expansion slot 1.
v If you have installed an optional PCI-X riser-card assembly in the server, you can
install a full-height, three-quarter-length PCI-X 64/133 MHz adapter in the PCI-X
slot on the riser-card assembly.
Note: When the optional Remote Supervisor Adapter II SlimLine is installed in
the server, you can install only a half-length adapter in the PCI-X slot.
v The optional Remote Supervisor Adapter II SlimLine can be installed only in the
dedicated connector on the system board (see “System-board optional-device
v The server uses a rotational interrupt technique to configure PCI Express
adapters so that you can install PCI Express adapters that do not support
sharing of interrupts.
18 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
v An optional ServeRAID™-MR10i controller provides RAID level-5 support to the
2.5-inch hot-swap drives and supports an external storage enclosure. A
ServeRAID-MR10i controller supports the 2.5-inch hard disk drives without
modification.
v An optional SAS HBA Controller adapter enables you to connect external storage
devices, such as SAS or SATA hard disk drives or tape drives, to a simple-swap
SATA model server.
v The server scans the PCI slots to assign system resources. The scan sequence
is related to the startup sequence. If you have not changed the default startup
sequence, the server scans the PCI slots in the following order: the integrated
Ethernet controllers 1 and 2; then, the drives that are connected to the
SAS/SATA controller; then, PCI Express slots 1 and 2.
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
Expansion-slot cover
Adapter
Adapter support bracket
ꢀ4ꢁ
ꢀ5ꢁ
ꢀ6ꢁ
Expansion slot
Riser-card assembly
Expansion slot 2
Chapter 2. Installing optional devices 19
Download from Www.Somanuals.com. All Manuals Search And Download.
To install an adapter, complete the following steps:
2. Turn off the server and peripheral devices, and disconnect the power cord and
all external cables. Remove the cover.
3. If you have installed an optional PCI-X riser-card assembly, disconnect the
riser-card power cableꢀ1ꢁ from the riser-card assembly.
4. Grasp the riser card at the front and rear edges and lift to remove the
riser-card assemblyꢀ1ꢁ. Place the riser-card assembly on a flat,
static-protective surface.
5. Remove the expansion-slot cover on the slot that you intend to use.
Attention: PCI expansion-slot covers must be installed on all vacant slots.
This maintains the electronic emissions characteristics of the server and
ensures proper cooling of server components.
6. Follow the instructions that come with the adapter to set any jumpers or
switches.
20 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention: When you install an adapter, make sure that it is completely and
correctly seated in the expansion slot in the riser card. Incomplete insertion
might cause damage to the riser card, system board, or the adapter when you
turn on the server.
7. Carefully grasp the adapter by its top edge or upper corners and align it with
the expansion slot in the riser card assembly; then, press the adapter firmly
into the expansion slot.
ꢀ1ꢁ
ꢀ2ꢁ
Adapter bracket
Expansion-slot bracket
ꢀ3ꢁ
ꢀ4ꢁ
Tab
Adapter
Important: Make sure that the U-shaped opening in the metal adapter bracket
engages the tab on the expansion-slot bracket.
8. Follow the cabling instructions, if any, that come with the adapter.
9. Reinstall the riser-card assembly. Make sure that the riser-card assembly is
fully seated in the riser-card connectors on the system board.
10. If you have installed an optional PCI-X riser-card assembly in the server,
reconnect the riser-card power cable ꢀ1ꢁ to the riser-card assembly.
11. If you are installing a ServeRAID-MR10i controller (2.5-inch drive models only),
complete the following steps:
Chapter 2. Installing optional devices 21
Download from Www.Somanuals.com. All Manuals Search And Download.
a. Disconnect the existing SAS/SATA controller signal cable from the hard
disk drive backplane and from the controller; then, remove the cable from
the server.
b. Route the ServeRAID-MR10i signal cable as shown in the following
illustration and connect it to the hard disk drive backplane.
ꢀ1ꢁ
ꢀ2ꢁ
ServeRAID controllerJ8
Hard disc drive backplane
ꢀ3ꢁ
ꢀ4ꢁ
J9
J8
If you have other devices to install, do so now. Otherwise, go to “Completing the
Installing an IBM® Remote Supervisor Adapter II SlimLine
Install an optional Remote Supervisor Adapter II SlimLine in the Remote Supervisor
Adapter II SlimLine connector on the system board. See the illustration in
“System-board optional-device connectors” on page 9 for the location of the
connector. After the Remote Supervisor Adapter II SlimLine is installed, the
systems-management port on the rear of the server is active.
Important: When the optional Remote Supervisor Adapter II SlimLine is installed in
the server, you can install only a half-length adapter in expansion slot 1.
Notes:
1. When you start the server for the first time after you install a Remote Supervisor
Adapter II SlimLine, the startup process will take several minutes longer than a
typical startup.
2. Earlier versions of the Remote Supervisor Adapter II SlimLine might not work in
supported Remote Supervisor Adapter II SlimLine versions.
To install a Remote Supervisor Adapter II SlimLine, complete the following steps.
22 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ1ꢁ
ꢀ2ꢁ
Remote Supervisor Adapter II
SlimLine
Mounting bracket
ꢀ3ꢁ
ꢀ4ꢁ
Mounting bracket
Mounting bracket retention latch
2. Turn off the server and peripheral devices, and disconnect the power cord and
all external cables. Remove the cover.
3. If you have installed an optional PCI-X riser-card assembly, disconnect the
riser-card power cable ꢀ1ꢁ from the riser-card assembly.
4. Grasp the riser-card assembly at the front and rear edges and lift to remove it
from the server. Place the riser-card assembly on a flat, static-protective
surface.
5. Put the protective plastic cover that came with the adapter on the Remote
Supervisor Adapter II SlimLine.
6. Turn the Remote Supervisor Adapter II SlimLine so that the keys on the
connector align correctly with the connector on the system board.
Chapter 2. Installing optional devices 23
Download from Www.Somanuals.com. All Manuals Search And Download.
7. At a downward angle, insert the free end of the adapter under the tab on the
mounting bracket, aligning the holes in the adapter with the posts on the
mounting bracket. Rotate the rear of the adapter into the rear mounting
bracket, aligning the holes in the adapter with the posts on the rear mounting
bracket.
8. Press the Remote Supervisor Adapter II SlimLine firmly into the connector and
make sure that all tabs on both mounting brackets secure the adapter in place.
Attention: Incomplete insertion might cause damage to the server or the
adapter.
9. If a three-quarter-length adapter is installed in expansion slot 1 on the
riser-card assembly, remove it. You can replace it with a half-length adapter if
you choose to do so.
10. Reinstall the riser-card assembly. Make sure that the riser-card assembly is
fully seated in the riser-card connectors on the system board.
11. If you have installed an optional PCI-X riser-card assembly, reconnect the
riser-card power cable ꢀ1ꢁ to the riser-card assembly.
See the documentation that comes with the Remote Supervisor Adapter II SlimLine
for information about installing the firmware and configuring the adapter. Create a
backup copy of the configuration so that if you have to replace the adapter in the
future you can restore the configuration.
If you have other devices to install, do so now. Otherwise, go to “Completing the
Completing the installation
To complete the installation, complete the following steps:
2. Install the server in the rack cabinet. See the Rack Installation Instructions that
come with the server for detailed information about how to install the server in a
rack cabinet.
24 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention:
v Install the server only in a rack cabinet that has perforated doors.
v Do not leave open space above or below an installed server in your rack
cabinet. To help prevent damage to server components, always install a filler
panel to cover the open space and to help ensure proper air circulation. See
the documentation that comes with the rack cabinet for more information.
for more information.
page 26 for more information.
Installing the cover
To install the cover, place it into position and slide it forward.
Connecting the cables
The following illustrations show the locations of the input and output connectors on
the front and rear of the server.
Front
ꢀ1ꢁ
USB 1 connector
ꢀ2ꢁ
USB 2 connector
Chapter 2. Installing optional devices 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear
You
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
Power-cord connector
Systems-management connector
USB 3 connector
ꢀ5ꢁ
ꢀ6ꢁ
ꢀ7ꢁ
ꢀ8ꢁ
Ethernet 1 connector
Ethernet 2 connector
Video connector
USB 4 connector
Serial connector
must turn off the server before you connect or disconnect cables.
See the documentation that comes with any external devices for additional cabling
instructions. It might be easier for you to route cables before you connect the
devices to the server.
Cable identifiers are printed on the cables that come with the server and devices.
Use these identifiers to connect the cables to the correct connectors.
If the server comes with an installed operating system, see the documentation that
comes with the operating system for additional cabling instructions.
There is no keyboard connector or mouse connector on the server. You can
connect a USB keyboard and USB mouse to the server by using the USB
connectors.
Updating the server configuration
When you start the server for the first time after you add or remove an internal
optional device or external SAS device, you might receive a message that the
configuration has changed. The Configuration/Setup Utility program starts
automatically so that you can save the new configuration settings. For more
information, see Chapter 4, “Configuring the server,” on page 31.
Some optional devices have device drivers that you must install. For information
about installing device drivers, see the documentation that comes with each device.
If the server has a RAID configuration that uses the SAS/SATA controller with
integrated RAID and you have installed or removed a hard disk drive, you might
have to reconfigure the disk arrays.
If the server has an optional RAID adapter and you have installed or removed a
hard disk drive, see the documentation that comes with the RAID adapter for
information about reconfiguring the disk arrays.
For information about configuring the integrated Gigabit Ethernet controllers, see
the User’s Guide.
26 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Server controls, LEDs, and power
This chapter describes the controls and light-emitting diodes (LEDs) and how to
turn the server on and off.
Front view
The following illustration shows the controls, light-emitting diodes (LEDs), and
connectors on the front of the server.
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
Power-on LED
Power-control button
Reset button
Hard-disk-drive activity LED
Locator LED
ꢀ6ꢁ
ꢀ7ꢁ
ꢀ8ꢁ
ꢀ9ꢁ
System Error LED
USB 1 connector
USB 2 connector
CD drive activity LED
ꢀ10ꢁ CD-eject button
Power-on LED: When this LED is lit and not flashing, it indicates that the server is
turned on. When this LED is flashing, it indicates that the server is turned off and
still connected to an ac power source. When this LED is off, it indicates that ac
power is not present, or the power supply or the LED itself has failed.
Note: If this LED is off, it does not mean that there is no electrical power in the
server. The LED might be burned out. To remove all electrical power from the
server, you must disconnect the power cord from the electrical outlet.
Power-control button: Press this button to turn the server on and off manually. A
power-control-button shield comes installed around the button to prevent the server
from being turned off accidentally. You can remove this disk-shaped shield if you
prefer.
Reset button: Press this button to reset the server and run the power-on self-test
(POST). You might have to use a pen or the end of a straightened paper clip to
press the button.
Hard disk drive activity LED: When this LED is flashing, it indicates that a hard
disk drive is in use.
Locator LED: This LED can be lit remotely by the system administrator to aid in
visually locating the server.
System-error LED: When this LED is lit, it indicates that a system error has
occurred. An LED on the system board might also be lit to help isolate the error.
© Lenovo 2008. Portions © IBM Corp. 2008.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
USB connectors: Connect a USB device to either of these connectors.
CD-eject button: Press this button to release a CD from the CD drive.
CD drive activity LED: When this LED is lit, it indicates that the CD drive is in use.
Rear view
The following illustration shows the LEDs on the rear of the server.
ꢀ1ꢁ
ꢀ2ꢁ
Ethernet 1 activity LED
Ethernet 1 link LED
ꢀ3ꢁ
ꢀ4ꢁ
Ethernet 2 activity LED
Ethernet 2 link LED
Ethernet activity LED: This LED is on each Ethernet connector. When this LED is
lit, it indicates that there is activity between the server and the network.
Ethernet link LED: This LED is on each Ethernet connector. When this LED is lit, it
indicates that the Ethernet controller is connected to the network.
The following illustration shows the connectors on the rear of the server.
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
Power-cord connector
Systems-management connector
USB 3 connector
ꢀ5ꢁ
ꢀ6ꢁ
ꢀ7ꢁ
ꢀ8ꢁ
Ethernet 1 connector
Ethernet 2 connector
Video connector
USB 4 connector
Serial connector
Power-cord connector: Connect the power cord to this connector.
Serial connector: Connect a 9-pin serial device to this connector.
Video connector: Connect a monitor to this connector.
Ethernet connector: Use either of these connectors to connect the server to a
network. Ethernet connector 1 supports Serial over LAN (SOL).
USB connector: Connect a USB device to either of these connectors.
28 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Systems-management connector: Connect the server to a network for
systems-management information control. This connector is active only if you have
installed a Remote Supervisor Adapter II SlimLine, and it is used only by the
Remote Supervisor Adapter II SlimLine.
Server power features
When the server is connected to an ac power source but is not turned on, the
operating system does not run, and all core logic except for the service processor is
shut down; however, the server can respond to requests from the service processor
(the baseboard management controller), such as a remote request to turn on the
server.
Turning on the server
Approximately 20 seconds after the server is connected to ac power, the
power-control button becomes active, and one or more fans might start running to
provide cooling while the server is connected to power. You can turn on the server
and start the operating system by pressing the power-control button.
The server can also be turned on in any of the following ways:
v If a power failure occurs while the server is turned on, the server will restart
automatically when power is restored.
v If your operating system supports the systems-management software for an
optional Remote Supervisor Adapter II SlimLine, the systems-management
software can turn on the server.
v If your operating system supports the Wake on LAN feature, the Wake on LAN
feature can turn on the server.
Note: When 4 GB or more of memory (physical or logical) is installed, some
memory is reserved for various system resources and is unavailable to the
operating system. The amount of memory that is reserved for system resources
depends on the operating system, the configuration of the server, and the
configured PCI optional devices.
Turning off the server
When you turn off the server and leave it connected to ac power, the server can
respond to requests from the service processor, such as a remote request to turn
on the server. While the server remains connected to ac power, one or more fans
might continue to run. To remove all power from the server, you must disconnect it
from the power source.
Some operating systems require an orderly shutdown before you turn off the server.
See your operating-system documentation for information about shutting down the
operating system.
Chapter 3. Server controls, LEDs, and power 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
2
1
The server can be turned off in any of the following ways:
v You can turn off the server from the operating system, if your operating system
supports this feature. After an orderly shutdown of the operating system, the
server will be turned off automatically.
v You can press the power-control button to start an orderly shutdown of the
operating system and turn off the server, if your operating system supports this
feature.
v If the operating system stops functioning, you can press and hold the
power-control button for more than 4 seconds to turn off the server.
v If an optional Remote Supervisor Adapter II SlimLine is installed in the server, the
server can be turned off from the Remote Supervisor Adapter II SlimLine user
interface.
v The integrated systems-management processor (mini-BMC) can turn off the
server as an automatic response to a critical system failure.
v You can turn off the server through a request from the service processor.
30 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Configuring the server
Lenovo provides a number of programs to assist you with getting your server up
and running quickly.
v ThinkServer EasyStartup program
This program simplifies the process of installing the operating system and
devices drivers. It is on the ThinkServer EasyStartup DVD provided with your
server. For details, see “Using the ThinkServer EasyStartup program” on page
v Configuration/Setup Utility program
This program enables you to configure hardware settings and preferences in the
BIOS. For details, see “Using the Configuration/Setup Utility program” on page
v RAID configuration programs
– Adaptec RAID (HOSTRaid) Configuration Utility program:
This program is part of the BIOS code on models that have an integrated
ServeRAID-8e (Adaptec HostRAID) controller.
– LSI Configuration Utility
This program is part of the BIOS code on models with an optional LSI storage
controller with RAID capability.
v Broadcom Gigabit Ethernet Utility program:
Use this program to configure the network as a startable (bootable) device or
specify where the network startup option is displayed in the startup sequence.
For additional information, see “Enabling the Broadcom Gigabit Ethernet Utility
v Baseboard management controller SMBridge management utility program:
Use these programs to configure the baseboard management controller,
download firmware updates, download SDR/FRU updates, and remotely manage
a network.
v ThinkServer EasyManage products
ThinkServer EasyManage Core Server and ThinkServer EasyManage Remote
Client work together to provide centralized hardware and software inventory
management and secure automated system management through a single
console. See “Using ThinkServer EasyManage products” on page 33.
The following table lists the different server configurations and the applications that
are available for configuring and managing RAID arrays.
Table 3. Configuration and management applications for RAID arrays
RAID array configuration
RAID array management
(before operating system is (after operating system is
Server configuration
installed)
installed)
Integrated SATA and no SAS None
controller card installed
None
SAS/SATA controller card
(LSI 1064) installed
LSI Logic Configuration Utility MegaRAID Storage Manager
(Ctrl+C during server
startup), ServerGuide
© Lenovo 2008. Portions © IBM Corp. 2008.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3. Configuration and management applications for RAID arrays (continued)
RAID array configuration
RAID array management
(before operating system is (after operating system is
Server configuration
installed)
installed)
ServeRAID-MR10i adapter
installed (2.5-inch drive
models only)
WebBIOS Configuration
Utility (Ctrl+H during server
startup), BIOS
WebBIOS Configuration
Utility (Ctrl+H during server
startup), MegaCLI
Configuration/Setup Utility
program (Ctrl+A during server
startup), ServerGuide
(command-line interface)
For more information about these programs, see “Configuring the server” in the
User Guide on the ThinkServer Documentation DVD.
Using the ThinkServer EasyStartup program
The ThinkServer EasyStartup program simplifies the process of installing the
operating system and devices drivers by performing the following tasks:
v Detects installed hardware devices
v Guides you through the process of creating a response file
v Prepares the hard disk for installation
v Prompts you to insert the operating-system installation disc
v Initiates an unattended installation of the operating system and device drivers for
most adapters and devices
The program is contained on the ThinkServer EasyUpdate disc provided with your
server. If you did not receive an EasyStartup DVD with your server, you can
program has a built-in help system and User Guide to answer any questions you
might have. The program also provides compatibility notes to help you determine
what server configurations and operating systems are supported by that specific
version of the program.
The ThinkServer EasyStartup program also enables you to save the response file
on a USB device or diskette for reuse, and an option that enables you to install an
operating systems using the saved response. This option is useful if you intend to
install the same operating system on similarly configured ThinkServer servers.
Notes:
1. If you intend to implement a RAID, make sure your storage controller or RAID
adapter is configured correctly before you use the ThinkServer EasyStartup
program to install the operating system.
2. If you are using any external storage devices or fiber channels, use the utilities
provided with the device. You also will have to provide the device drivers for
these devices and install them after the EasyStartup program finishes installing
the operating system.
3. The EasyStartup DVD requires that you have a DVD drive that is configured as
your first device in the startup sequence. Use the Configuration/Setup Utility
program to view or change your startup sequence. See “Using the
4. To install an operating system, you need the operating system installation disc
(CD or DVD) and the associated product key, if one was provided.
32 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
To start the EasyStartup DVD, do the following:
1. Insert the EasyStartup DVD and restart the server. If the EasyStartup program
does not start, see “EasyStartup problems” on page 54.
2. Follow the instructions on the screen and continue to the main interface.
3. When you arrive at the Home screen, do any of the following:
v Click Compatibility notes to view detailed information about the operating
systems and server configurations supported by that version of the
EasyStartup program.
v Click User Guide to view an overview of the various functions provided by
that version of the EasyStartup program.
v
Click Hardware list to view a list of hardware detected by the ThinkServer
EasyStartup program.
v Click Install operating system to begin the process of creating a response file
and installing the operating system. As part of this procedure you will be
given the opportunity to include the ThinkServer EasyUpdate program and
the ThinkServer EasyManage products (ThinkServer EasyManage Core
Server or ThinkVantage EasyManage Remote Client) as part of the
installation process. You also can provide one or more command-line based
instructions to be run at the end of the operating system installation process.
Click About to view version information and legal notices.
To use the EasyStartup DVD to install an operation system using a preexisting
response file, do the following:
1. Insert the EasyStartup DVD and restart the server. If the EasyStartup program
does not start, see “EasyStartup problems” on page 54.
2. Follow the instructions on the screen until you get to the Start option screen.
3. When the Start option screen is displayed, do the following:
a. Insert the USB device or diskette that contains the response file.
b. Select Install the operating system using a preexisting response file.
c. Click OK.
4. Follow the remaining instructions on the screen to complete the procedure.
Using ThinkServer EasyManage products
ThinkServer EasyManage Core Server provides centralized hardware and software
inventory management and secure automated system management through a
single console. The ThinkServer EasyManage Agent enables other computers and
servers to be managed by the centralized console.
You can install the ThinkServer EasyManage Core Server program from the
ThinkServer EasyManage CD or you can download and install the program from
http://www.lenovo.com/support. After one instance of the ThinkServer EasyManage
Core Server has been installed, you can use the ThinkServer EasyManage Agent
installer to install the agent on other servers and clients on the network.
Also, the EasyServer EasyStartup program provides an option to install these
products as part of the operating system installation process.
Chapter 4. Configuring the server 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Configuration/Setup Utility program
The Configuration/Setup Utility program is part of the BIOS. You can use it to
perform the following tasks:
v View configuration information
v View and change assignments for devices and I/O ports
v Set the date and time
v Set and change passwords
v Set and change the startup characteristics of the server and the order of startup
devices (startup-drive sequence)
v Set and change settings for advanced hardware features
v View and clear the event and error logs
v Change interrupt request (IRQ) settings
v Resolve configuration conflicts
To start the Configuration/Setup Utility program, complete the following steps:
1. Turn on the server.
2. When the message Press F1 for Configuration/Setup is displayed, press F1.
If an administrator password has been set, you must type the administrator
password to access the full Configuration/Setup Utility menu.
3. Follow the instructions on the screen.
See the User's Guide that is on the ThinkServer Documentation DVD for more
information about using the Configuration/Setup Utility program.
Using the LSI Logic Configuration Utility program
Use the LSI Logic Configuration Utility program to configure hot-swap hard disk
drives that are connected to the SAS/SATA controller.
Important:
v If the server is a simple-swap SATA model that contains a SATA RAID back
plate, you can use the LSI Logic Configuration Utility program to configure the
simple-swap SATA hard disk drives.
v If you install an optional RAID controller in the server, such as the
ServeRAID-MR10i controller, use the configuration software that comes with the
adapter to configure the hard disk drives.
To start the LSI Logic Configuration Utility program, complete the following steps:
1. Turn on the server.
2. When the prompt Press CTRL-C to start LSI Logic Configuration Utility...
is displayed, press Ctrl+C. If you have set an administrator password, you are
prompted to type the password.
3. Use the arrow keys to select the adapter (SAS controller) for which you want to
change settings. Use the Help function to see instructions and available actions
for this screen. If you select SAS Topology or Advanced Adapter Properties,
additional screens are displayed.
4. To change the settings of the selected items, follow the instructions on the
screen.
5. Press Enter to save your changes.
34 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the baseboard management controller
The baseboard management controller provides basic environmental monitoring
functions for the server. If an environmental condition exceeds a threshold or if a
system component fails, the baseboard management controller lights LEDs to help
you diagnose the problem and also records the error in the BMC system event log.
The baseboard management controller also provides command-line interface
remote server management capabilities through the Avocent SMBridge
management utility program. The command-line interface provides direct access to
server management functions through the Intelligent Platform Management Interface
(IPMI) protocol. Use the command-line interface to issue commands to control the
server power, view system information, and identify the server. You can also save
one or more commands as a text file and run the file as a script.
Configuring the Gigabit Ethernet controllers
The Ethernet controllers are integrated on the system board. They provide an
interface for connecting to a 10 Mbps, 100 Mbps, or 1 Gbps network and provide
full-duplex (FDX) capability, which enables simultaneous transmission and reception
of data on the network. If the Ethernet ports in the server support auto-negotiation,
the controllers detect the data-transfer rate (10BASE-T, 100BASE-TX, or
1000BASE-T) and duplex mode (full-duplex or half-duplex) of the network and
automatically operate at that rate and mode.
Note: The Ethernet controller for Ethernet connector 1 supports Serial over LAN
(SOL).
You do not have to set any jumpers or configure the controllers. However, you must
install a device driver to enable the operating system to address the controllers. For
device drivers and information about configuring the Ethernet controllers, see the
Broadcom NetXtreme II Gigabit Ethernet Software CD that comes with the server.
To find updated information about configuring the controllers, complete the following
steps.
Note: Changes are made periodically to the Lenovo Web site. The actual
procedure might vary slightly from what is described in this document.
2. Enter your product number (machine type and model number) or select Servers
from the Select your product list.
3. Select Servers from the Brand list.
4. From Family list, select ThinkServer RS110, and click Continue.
Chapter 4. Configuring the server 35
Download from Www.Somanuals.com. All Manuals Search And Download.
36 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Solving problems
This chapter provides basic troubleshooting information to help you solve some
common problems that might occur while you are setting up the server.
If you cannot locate and correct a problem by using the information in this chapter,
Maintenance Manual on the ThinkServer Documentation DVD.
Diagnostic tools overview
The following tools are available to help you diagnose and solve hardware-related
problems:
v POST beep codes
The power-on self-test beep codes indicate the detection of a problem.
– One beep indicates successful completion of POST, with no errors.
– More than one beep indicates that POST detected a problem. Error messages
also appear during startup if POST detects a hardware-configuration problem.
ThinkServer Documentation DVD for more information.
v Troubleshooting charts
These charts list problem symptoms and actions to correct the problems. See
“Troubleshooting tables” on page 45 for more information.
POST beep codes
POST emits one beep to signal successful completion. If POST detects a problem
during startup, other beep codes might occur. Use the following beep code
descriptions to help diagnose and solve problems that are detected during startup.
Note: See the Hardware Maintenance Manual on the ThinkServer Documentation
DVD for more information about the POST beep codes.
One beep
POST was completed successfully without detecting any errors.
Other beep codes
See the Hardware Maintenance Manual on the ThinkServer Documentation
DVDD for information about other beep codes.
© Lenovo 2008. Portions © IBM Corp. 2008.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
POST error codes
The following table provides an abbreviated list of the error codes that might appear
during POST. See the Hardware Maintenance Manual on the ThinkServer
Documentation DVD for more information about the POST error codes. To check for
updated technical information, complete the following steps.
Note: Changes are made periodically to the Lenovo Web site. The actual
procedure might vary slightly from what is described in this document.
2. Enter your product number (machine type and model number) or select Servers
from the Select your product list.
3. Select Servers from the Brand list.
4. From Family list, select ThinkServer RS110, and click Continue.
5. Click User's guides and manuals for documentation.
Table 4. Abbreviated list of POST error codes
v
v
Follow the suggested actions in the order in which they are listed in the Action
column until the problem is solved.
See the parts listing in the Hardware Maintenance Manual to determine which
components are customer replaceable units (CRU) and which components are field
replaceable units (FRU).
v
If an action step is preceded by “(Trained service technician only),” that step must
be performed only by a trained service technician.
Error code
Description
Action
062
Three consecutive boot failures
using the default configuration.
1. Update the system firmware to
the latest level (see the
Hardware Maintenance Manual
on the ThinkServer
Documentation DVD).
2. (Trained service technician
only) Replace the system
board.
101
102
151
Tick timer internal interrupt failure. (Trained service technician only)
Replace the system board.
Internal timer channel 2 test
failure.
(Trained service technician only)
Replace the system board.
Real-time clock error.
1. Reseat the battery.
2. Replace the following
components one at a time, in
the order shown, restarting the
server each time:
a. Battery
b. (Trained service technician
only) System board
38 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4. Abbreviated list of POST error codes (continued)
v
v
Follow the suggested actions in the order in which they are listed in the Action
column until the problem is solved.
See the parts listing in the Hardware Maintenance Manual to determine which
components are customer replaceable units (CRU) and which components are field
replaceable units (FRU).
v
If an action step is preceded by “(Trained service technician only),” that step must
be performed only by a trained service technician.
Error code
Description
Action
162
Invalid configuration information or
CMOS random-access memory
(RAM) checksum failure.
1. Run the Configuration/Setup
Utility program, select Load
Default Settings, and save the
settings.
2. Reseat the battery.
3. Replace the battery.
4. (Trained service technician
only) Replace the system
board.
163
164
The time of day has not been set. Run the Configuration/Setup Utility
program, set the date and time,
and save the settings.
Memory size has changed.
1. Run the Configuration/Setup
Utility program; then, exit,
saving the configuration
settings.
2. Reseat the DIMMs.
184
Power-on password damaged.
1. Run the Configuration/Setup
Utility program, select Load
Default Settings, and save the
settings.
2. Reseat the battery.
3. Replace the following
components one at a time, in
the order shown, restarting the
server each time:
a. Battery
b. (Trained service technician
only) System board
187
189
VPD serial number not set.
1. Reseat the optional Remote
Supervisor Adapter II SlimLine.
2. (Trained service technician
only) Replace the system
board.
Three attempts were made to
Restart the server and enter the
access the server with an incorrect administrator password; then, run
password.
the Configuration/Setup Utility
program and change the power-on
password.
Chapter 5. Solving problems 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4. Abbreviated list of POST error codes (continued)
v
v
Follow the suggested actions in the order in which they are listed in the Action
column until the problem is solved.
See the parts listing in the Hardware Maintenance Manual to determine which
components are customer replaceable units (CRU) and which components are field
replaceable units (FRU).
v
If an action step is preceded by “(Trained service technician only),” that step must
be performed only by a trained service technician.
Error code
Description
Action
289
A failing DIMM was disabled.
1. Make sure that the DIMM is
installed correctly (see
2. Reseat the DIMM.
3. Replace the DIMM.
178x
Fixed disk error.
Note: x is the drive that has the
error.
1. Run the hard disk drive
diagnostic tests on drive x (see
“Running the diagnostic
programs” in the Hardware
Maintenance Manual on the
ThinkServer Documentation
DVD).
2. Reseat the following
components, depending on the
server model:
v Hot-swap models: Hard disk
drive x
v Simple-swap models:
a. Hard disk drive x
b. Hard disk drive x cable
3. Replace the following
components one at a time,
depending on the server
model, in the order shown,
restarting the server each time:
v Hot-swap models:
a. Hard disk drive x
b. Hard disk drive
backplane
c. (Trained service
technician only) System
board
v Simple-swap models:
a. Hard disk drive x
b. Hard disk drive x cable
c. (Trained service
technician only) System
board
180x
A PCI adapter requested a
resource that is not available.
Run the Configuration/Setup Utility
program and make sure that the
resources that are needed by the
PCI adapter are available.
40 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4. Abbreviated list of POST error codes (continued)
v
v
Follow the suggested actions in the order in which they are listed in the Action
column until the problem is solved.
See the parts listing in the Hardware Maintenance Manual to determine which
components are customer replaceable units (CRU) and which components are field
replaceable units (FRU).
v
If an action step is preceded by “(Trained service technician only),” that step must
be performed only by a trained service technician.
Error code
Description
Action
1962
A hard disk drive does not contain
a valid boot sector.
1. Make sure that a startable
operating system is installed.
2. Run the hard disk drive
diagnostic tests.
3. Reseat the following
components:
a. Hard disk drive
b. Hard disk drive backplane
cable or back plate cables
4. Replace the following
components one at a time, in
the order shown, restarting the
server each time:
a. (Hot-swap models) Hard
disk drive cable
b. Hard disk drive
c. Hard disk drive backplane
or back plate
d. (Trained service technician
only) System board
5962
Internal CD/DVD drive
configuration changed.
1. Run the Configuration/Setup
Utility program and load the
default settings (see “Using the
An expected CD or DVD drive was
not detected.
2. Reseat the following
components:
a. DVD drive cable
b. DVD drive
3. Replace the following
components one at a time, in
the order shown, restarting the
server each time:
a. DVD drive cable
b. DVD drive
c. (Trained service technician
only) System board
Chapter 5. Solving problems 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4. Abbreviated list of POST error codes (continued)
v
v
Follow the suggested actions in the order in which they are listed in the Action
column until the problem is solved.
See the parts listing in the Hardware Maintenance Manual to determine which
components are customer replaceable units (CRU) and which components are field
replaceable units (FRU).
v
If an action step is preceded by “(Trained service technician only),” that step must
be performed only by a trained service technician.
Error code
Description
Action
00012000
Processor machine check error.
1. (Trained service technician
only) Reseat the
microprocessor.
2. Replace the following
components one at a time, in
the order shown, restarting the
server each time:
a. (Trained service technician
only) Microprocessor
b. (Trained service technician
only) System board
00019701
01298001
Microprocessor x is not functioning Make sure that microprocessor x is
or failed the built-in self-test.
installed correctly. If the problem
remains, call for service.
No update data for microprocessor
1.
1. Update the BIOS code again
(see the Hardware
Maintenance Manual on the
ThinkServer Documentation
DVD.
2. (Trained service technician
only) Reseat the
microprocessor.
3. (Trained service technician
only) Replace the
microprocessor.
01298101
Bad update data for
microprocessor 1.
1. Update the BIOS code again
(see the Hardware
Maintenance Manual on the
ThinkServer Documentation
DVD).
2. (Trained service technician
only) Reseat the
microprocessor.
3. (Trained service technician
only) Replace the
microprocessor.
42 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4. Abbreviated list of POST error codes (continued)
v
v
Follow the suggested actions in the order in which they are listed in the Action
column until the problem is solved.
See the parts listing in the Hardware Maintenance Manual to determine which
components are customer replaceable units (CRU) and which components are field
replaceable units (FRU).
v
If an action step is preceded by “(Trained service technician only),” that step must
be performed only by a trained service technician.
Error code
Description
Action
I9990301
Hard disk drive boot sector error.
1. Reseat the following
components, depending on the
server model:
v Hot-swap models:
a. Hard disk drive
b. SAS/SATA controller
v Simple-swap models:
a. Hard disk drive
b. Hard disk drive cable
2. Replace the following
components one at a time,
depending on the server
model, in the order shown,
restarting the server each time:
v Hot-swap models:
a. Hard disk drive
b. Hard disk drive
backplane
c. SAS/SATA controller
d. (Trained service
technician only) System
board
v Simple-swap models:
a. Hard disk drive
b. Hard disk drive cable
c. (Trained service
technician only) System
board
Chapter 5. Solving problems 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4. Abbreviated list of POST error codes (continued)
v
v
Follow the suggested actions in the order in which they are listed in the Action
column until the problem is solved.
See the parts listing in the Hardware Maintenance Manual to determine which
components are customer replaceable units (CRU) and which components are field
replaceable units (FRU).
v
If an action step is preceded by “(Trained service technician only),” that step must
be performed only by a trained service technician.
Error code
Description
Action
I9990305
An operating system was not
found.
1. Make sure that a bootable
operating system is installed.
2. Run the hard disk drive
diagnostic tests.
3. Reseat the following
components:
a. Hard disk drive
b. CD or DVD drive and
cables
c. (Trained service technician
only) System board
4. Replace the components listed
in step 3 one at a time, in the
order shown, restarting the
server each time.
I9990650
AC power has been restored.
1. Check the power cables.
2. Check for interruption of the
power supply.
44 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting tables
Use the troubleshooting tables to find solutions to problems that have identifiable
symptoms. See the Hardware Maintenance Manual on the LenovoThinkServer
Documentation DVD for more detailed troubleshooting information. If you cannot
find a problem in these tables, run the diagnostic programs (see “Running the
diagnostic programs” in the Hardware Maintenance Manual ).
If you have just added new software or a new optional device and the server is not
working, complete the following steps before you use the troubleshooting tables:
2. Remove the software or device that you just added.
3. Run the diagnostic tests to determine whether the server is running correctly.
4. Reinstall the new software or new device.
CD or DVD drive problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
The CD or DVD drive is not
recognized.
1. Make sure that:
v All cables and jumpers are installed correctly.
v The signal cable and connector are not damaged and the connector pins are
not bent.
v All damaged parts are repaired or replaced.
v The correct device driver is installed for the CD or DVD drive.
2. Run the CD, CD-RW, or DVD drive diagnostic programs.
3. Reseat the following components:
a. CD or DVD drive
b. CD or DVD interface board cable
4. Replace the following components one at a time, in the order shown, restarting
the server each time:
a. CD or DVD drive
b. CD or DVD drive interface board cable
c. CD or DVD interface board
d. (Trained service technician only) System board
A CD or DVD is not working
correctly.
1. Clean the CD or DVD.
2. Run the CD or DVD drive diagnostic programs.
3. Reseat the CD or DVD drive.
4. Replace the CD or DVD drive.
Chapter 5. Solving problems 45
Download from Www.Somanuals.com. All Manuals Search And Download.
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
The CD or DVD drive tray is not
working.
1. Make sure that the server is turned on.
2. Insert the end of a straightened paper clip into the manual tray-release
opening.
3. Reseat the CD or DVD drive.
4. Replace the CD or DVD drive.
General problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
A cover lock is broken, an LED If the part is a CRU, replace it. If the part is a FRU, the part must be replaced by a
is not working, or a similar
problem has occurred.
trained service technician.
Hard disk drive problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
Not all drives are recognized by Remove the drive indicated on the diagnostic tests; then, run the hard disk drive
the hard disk drive diagnostic
test.
diagnostic test again. If the remaining drives are recognized, replace the drive that
you removed with a new one.
The server stops responding
during the hard disk drive
diagnostic test.
Remove the hard disk drive that was being tested when the server stopped
responding, and run the diagnostic test again. If the hard disk drive diagnostic test
runs successfully, replace the drive that you removed with a new one.
A hard disk drive was not
detected while the operating
system was being started.
Reseat all hard disk drives and cables; then, run the hard disk drive diagnostic
tests again.
A hard disk drive passes the
diagnostic test, but the problem
remains.
See “Solving undetermined problems” in the Hardware Maintenance Manual
46 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Intermittent problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
A problem occurs only
occasionally and is difficult to
diagnose.
1. Make sure that:
v All cables and cords are connected securely to the rear of the server and
attached devices.
v When the server is turned on, air is flowing from the fan grille. If there is no
airflow, the fan is not working. This can cause the server to overheat and
shut down.
USB keyboard, mouse, or pointing-device problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
All or some keys on the
keyboard do not work.
2. Make sure that:
v The keyboard cable is securely connected.
v The server and the monitor are turned on.
3. Move the keyboard cable to a different USB connector.
4. Replace the following components one at a time, in the order shown, restarting
the server each time:
a. Keyboard
b. (Only if the problem occurred with a front USB connector) Internal cables to
the operation information panel
c. (Only if the problem occurred with a front USB connector) Operator
information panel
d. (Trained service technician only) System board
Chapter 5. Solving problems 47
Download from Www.Somanuals.com. All Manuals Search And Download.
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
The USB mouse or USB
pointing device does not work.
1. Make sure that:
v The mouse or pointing-device USB cable is securely connected to the
server, and the device drivers are installed correctly.
v The server and the monitor are turned on.
2. If a USB hub is in use, disconnect the USB device from the hub and connect it
directly to the server.
3. Move the mouse or pointing device cable to another USB connector.
4. Replace the following components one at a time, in the order shown, restarting
the server each time:
a. Mouse or pointing device
b. (Only if the problem occurred with a front USB connector) Internal cables to
the operation information panel
c. (Only if the problem occurred with a front USB connector) Operator
information panel
d. (Trained service technician only) System board
48 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
The amount of system memory
that is displayed is less than the
amount of installed physical
memory.
1. Make sure that:
v No error LEDs are lit on the operator information panel.
v The memory modules are seated correctly.
v All banks of memory are enabled. The server might have automatically
disabled a memory bank when it detected a problem.
Configuration/Setup Utility program” on page 34); if a DIMM was disabled by a
systems-management interrupt (SMI), replace the DIMM.
3. Run memory diagnostics (see “Running the diagnostic programs” in the
Hardware Maintenance Manual ).
4. Add one pair of DIMMs at a time, making sure that the DIMMs in each pair
match.
5. Reseat the DIMMs.
6. Replace the following components one at a time, in the order shown, restarting
the server each time:
a. DIMMs
b. (Trained service technician only) System board
Microprocessor problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
The server emits a continuous
beep during POST, indicating
that the microprocessor is not
working correctly.
1. Correct any errors that are indicated by the LEDs (see “System-board LEDs” in
the Hardware Maintenance Manual ).
2. Make sure that the server supports the microprocessor.
3. (Trained service technician only) Make sure that the microprocessor is seated
correctly.
4. (Trained service technician only) Replace the microprocessor.
Chapter 5. Solving problems 49
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor problems
Some monitors have their own self-tests. If you suspect a problem with your
monitor, see the documentation that comes with the monitor for instructions for
testing and adjusting the monitor.
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
Testing the monitor
1. Make sure that the monitor cables are firmly connected.
2. Try using a different monitor on the server, or try testing the monitor on a
different server.
3. Run the diagnostic programs (see the Hardware Maintenance Manual ). If the
monitor passes the diagnostic programs, the problem might be a video device
driver.
4. (Trained service technician only) Replace the system board.
The screen is blank.
1. If the server is attached to a KVM switch, bypass the KVM switch to eliminate it
as a possible cause of the problem: connect the monitor cable directly to the
correct connector on the rear of the server.
2. Make sure that:
v The monitor cables are connected correctly.
v The monitor is turned on and the brightness and contrast controls are
adjusted correctly.
v Only a single beep sounds when the server is turned on.
Important: In some memory configurations, the 3-3-3 beep code might sound
during POST, followed by a blank monitor screen. If this occurs and the Boot
Fail Count option in the Start Options of the Configuration/Setup Utility
program is enabled, you must restart the server three times to reset the
configuration settings to the default configuration (the memory connector or
bank of connectors is enabled).
3. Make sure that the correct server is controlling the monitor, if applicable.
4. Make sure that damaged BIOS code is not affecting the video; see “Recovering
from BIOS update failure” in the Hardware Maintenance Manual .
5. See “Solving undetermined problems” in the Hardware Maintenance Manual .
The monitor works when you
turn on the server, but the
screen goes blank when you
start some application
programs.
1. Make sure that:
v The application program is not setting a display mode that is higher than the
capability of the monitor.
v You installed the necessary device drivers for the application.
2. Run video diagnostics (see the Hardware Maintenance Manual ).
v If the server passes the video diagnostics, the video is good; see “Solving
undetermined problems” in the Hardware Maintenance Manual .
v (Trained service technician only) If the server fails the video diagnostics,
replace the system board.
50 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
The monitor has screen jitter, or
the screen image is wavy,
unreadable, rolling, or distorted.
1. If the monitor self-tests show that the monitor is working correctly, consider the
location of the monitor. Magnetic fields around other devices (such as
transformers, appliances, fluorescent lights, and other monitors) can cause
screen jitter or wavy, unreadable, rolling, or distorted screen images. If this
happens, turn off the monitor.
Attention: Moving a color monitor while it is turned on might cause screen
discoloration.
Move the device and the monitor at least 305 mm (12 in.) apart, and turn on
the monitor.
Notes:
a. To prevent diskette drive read/write errors, make sure that the distance
between the monitor and any external diskette drive is at least 76 mm (3
in.).
b. Non-Lenovo monitor cables might cause unpredictable problems.
2. Reseat the following components:
v Monitor cable
v Remote Supervisor Adapter II SlimLine (if one is installed)
3. Replace the following components one at a time, in the order shown, restarting
the server each time:
a. Monitor cable
b. Monitor
c. Remote Supervisor Adapter II SlimLine (if one is installed)
d. (Trained service technician only) System board
Wrong characters appear on the
screen.
1. If the wrong language is displayed, update the BIOS code with the correct
language.
2. Reseat the monitor cable.
3. Replace the following components one at a time, in the order shown, restarting
the server each time:
a. Monitor
b. (Trained service technician only) System board
Chapter 5. Solving problems 51
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional-device problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
An optional device that was just
installed does not work.
1. Make sure that:
v You followed the installation instructions that came with the device and the
device is installed correctly.
v You have not loosened any other installed devices or cables.
v You updated the configuration information in the Configuration/Setup Utility
program. Whenever a device is changed, you must update the configuration.
2. Reseat the device that you just installed.
3. Replace the device that you just installed.
An optional device that used to
work does not work now.
1. Make sure that all of the cable connections for the device are secure.
2. If the device comes with test instructions, use those instructions to test the
device.
3. Reseat the failing device.
4. Replace the failing device.
52 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Power problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
The power-control button does
not work, and the reset button
does work (the server does not
start).
1. Make sure that the power-control button is working correctly:
a. Disconnect the server power cords.
b. Reconnect the power cords.
Note: The power-control button
will not function until 20
seconds after the server has
been connected to ac power.
c. Press the power-control button.
d. If the server does not start, disconnect the server power cords and reseat
the problem remains, replace the operator information panel.
2. Make sure that:
v The ac power cord is correctly connected to the server and to a working
electrical outlet.
v The server contains the correct type of DIMMs.
v The DIMMs are correctly seated.
v (Trained service technician only) The microprocessor is correctly installed.
3. If you just installed an optional device, remove it, and restart the server. If the
server now starts, you might have installed more devices than the power supply
supports.
4. Reseat the following components:
a. DIMMs
b. (Trained service technician only) Power-supply cables to all internal
components
c. (Trained service technician only) Power connector on the system board
5. Replace the following components one at a time, in the order shown, restarting
the server each time:
a. DIMMs
b. (Trained service technician only) Power supply
c. (Trained service technician only) System board
6. See “Solving undetermined problems” in the Hardware Maintenance Manual .
The server does not turn off.
1. Determine whether you are using an Advanced Configuration and Power
Interface (ACPI) or a non-ACPI operating system. If you are using a non-ACPI
operating system, complete the following steps:
a. Press Ctrl+Alt+Delete.
b. Turn off the server by pressing the power-control button for 5 seconds.
c. Restart the server.
d. If the server fails POST and the power-control button does not work,
disconnect the ac power cord for 20 seconds; then, reconnect the ac power
cord and restart the server.
2. If the problem remains or if you are using an ACPI-aware operating system,
suspect the system board.
The server unexpectedly shuts Call for service.
down, and the LEDs on the
operator information panel are
not lit.
Chapter 5. Solving problems 53
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial-device problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
The number of serial ports that
are identified by the operating
system is less than the number
of installed serial ports.
1. Make sure that:
v Each port is assigned a unique address in the Configuration/Setup Utility
program and none of the serial ports is disabled.
v The serial-port adapter (if one is installed) is seated correctly.
2. Reseat the serial port adapter.
3. Replace the serial port adapter.
A serial device does not work.
1. Make sure that:
v The device is compatible with the server.
v The serial port is enabled and is assigned a unique address.
2. Reseat the following components:
a. Failing serial device
b. Serial cable
3. Replace the following components one at a time, in the order shown, restarting
the server each time:
a. Failing serial device
b. Serial cable
c. (Trained service technician only) System board
EasyStartup problems
Table 5. EasyStartup DVD
v
v
v
Follow the suggested actions in the order in which they are listed in the Action Column until the problem
is resolved.
See the Hardware Maintenance Manual on the Documentation DVD to determine which components are
customer replaceable units (CRU’s) and which fields are field replacable units (FRU’s).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
The EasyStartup DVD
will not start.
v Make sure that the server supports the EasyStartup program and has a startable
(bootable) CD or DVD drive.
v If the startup (boot) sequence settings have been changed, make sure that the CD or
DVD drive is first in the startup sequence.
v If more than one CD or DVD drive is installed, make sure that only one drive is set as
the primary drive. Start the CD from the primary drive.
The ServeRAID Manager v Make sure that the hard disk drive is connected correctly.
program cannot view all v Make sure that the SAS hard disk drive cables are securely connected.
installed drives, or the
operating system cannot
be installed.
54 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5. EasyStartup DVD (continued)
v
v
v
Follow the suggested actions in the order in which they are listed in the Action Column until the problem
is resolved.
See the Hardware Maintenance Manual on the Documentation DVD to determine which components are
customer replaceable units (CRU’s) and which fields are field replacable units (FRU’s).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
The operating-system
installation program
continuously loops.
Make more space available on the hard disk.
The EasyStartup
Make sure that the operating-system media is supported by the EasyStartup program.
program will not start the See the EasyStartup DVD label for a list of supported operating-system versions.
operating-system media.
The operating system
cannot be installed; the
option is not available.
Make sure that the server supports the operating-system. If it does, either no logical drive
is defined (RAID servers), or the EasyStartup program is not installed. Run the
EasyStartup program and make sure that setup is complete.
Software problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
You suspect a software
problem.
1. To determine whether the problem is caused by the software, make sure that:
v The server has the minimum memory that is needed to use the software. For
memory requirements, see the information that comes with the software. If
you have just installed an adapter or memory, the server might have a
memory-address conflict.
v The software is designed to operate on the server.
v Other software works on the server.
v The software works on another server.
2. If you received any error messages when using the software, see the
information that comes with the software for a description of the messages and
suggested solutions to the problem.
3. Contact your place of purchase of the software.
Chapter 5. Solving problems 55
Download from Www.Somanuals.com. All Manuals Search And Download.
Universal Serial Bus (USB) device problems
v
v
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
See the parts listing in the Hardware Maintenance Manual to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Symptom
Action
A USB device does not work.
1. Make sure that:
v The correct USB device driver is installed.
v The operating system supports USB devices.
2. Make sure that the USB configuration options are set correctly in the
Configuration/Setup Utility program menu (see the User’s Guide for more
information).
3. If you are using a USB hub, disconnect the USB device from the hub and
connect it directly to the server.
Video problems
56 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Getting help and technical assistance
If you need help, service, or technical assistance or just want more information
about Lenovo products, you will find a wide variety of sources available from
Lenovo assist you. This section contains information about where to go for
additional information about Lenovo and Lenovo products, what to do if you
experience a problem with your system, and whom to call for service, if it is
necessary.
Before you call
Before you call, make sure that you have taken these steps to try to solve the
problem yourself:
v Check all cables to make sure that they are connected.
v Check the power switches to make sure that the system and any optional
devices are turned on.
v Use the troubleshooting information in your system documentation, and use the
diagnostic tools that come with your system. Information about diagnostic tools is
in the Hardware Maintenance Manual on the ThinkServer Documentation DVD
that comes with your system.
technical information, hints, tips, and new device drivers or to submit a request
for information.
You can solve many problems without outside assistance by using the information
available on the Lenovo support site or by following the troubleshooting procedures
that Lenovo provides in the documentation that is provided with your Lenovo
product. The documentation that comes with Lenovo systems also describes the
diagnostic tests that you can perform. Most systems, operating systems, and
programs come with documentation that contains troubleshooting procedures and
explanations of error messages and error codes. If you suspect a software problem,
see the documentation for the operating system or program.
Using the documentation
Information about your Lenovo system and preinstalled software, if any, or optional
device is available in the documentation that comes with the product. That
documentation can include printed documents, online documents, readme files, and
help files. Most of the documentation for your server is on the ThinkServer
Documentation DVD provided with your server. See the troubleshooting information
in your system documentation for instructions for using the diagnostic programs.
The troubleshooting information or the diagnostic programs might tell you that you
need additional or updated device drivers or other software. Lenovo maintains
pages on the World Wide Web where you can get the latest technical information
and download device drivers and updates. To access these pages, go to
http://www.lenovo.com/support and follow the instructions.
© Lenovo 2008. Portions © IBM Corp. 2008.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting help and information from the World Wide Web
On the World Wide Web, the Lenovo Web site has up-to-date information about
Lenovo systems, optional devices, services, and support. For general information
about Lenovo products or to purchase Lenovo products, go to http://
Calling for service
During the warranty period, you can get help and information by telephone through
the Customer Support Center.
These services are available during the warranty period:
v Problem determination - Trained personnel are available to assist you with
determining a hardware problem and deciding what action is necessary to fix the
problem.
v Hardware repair - If the problem is caused by hardware under warranty, trained
service personnel are available to provide the applicable level of service.
v Engineering Change management - There might be changes that are required
after a product has been sold. Lenovo or your reseller will make selected
Engineering Changes (ECs) available that apply to your hardware.
These items are not covered by the warranty:
v Replacement or use of parts not manufactured for or by Lenovo or
non-warranted Lenovo parts
v Identification of software problem sources
v Configuration of BIOS as part of an installation or upgrade
v Changes, modifications, or upgrades to device drivers
v Installation and maintenance of network operating systems (NOS)
v Installation and maintenance of application programs
Refer to the safety and warranty information that is provided with your computer for
a complete explanation of warranty terms. You must retain your proof of purchase
to obtain warranty service.
For a list of service and support phone numbers for your country or region, go to
and warranty information provided with your computer.
Note: Phone numbers are subject to change without notice. If the number for your
country or region is not provided, contact your Lenovo reseller or Lenovo marketing
representative.
If possible, be at your computer when you call. Have the following information
available:
v Machine type and model
v Serial numbers of our hardware products
v Description of the problem
v Exact working of any error messages
v Hardware and software configuration information
58 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Using other services
If you travel with a Lenovo notebook computer or relocate your computer to a
country where your desktop, notebook, or server machine type is sold, your
computer might be eligible for International Warranty Service, which automatically
entitles you to obtain warranty service throughout the warranty period. Service will
be performed by service providers authorized to perform warranty service.
Service methods and procedures vary by country, and some services might not be
available in all countries. International Warranty Service is delivered through the
method of service (such as depot, carry-in, or on-site service) that is provided in the
servicing country. Service centers in certain countries might not be able to service
all models of a particular machine type. In some countries, fees and restrictions
might apply at the time of service.
To determine whether your computer is eligible for International Warranty Service
and to view a list of the countries where service is available, go to
screen.
For technical assistance with the installation of, or questions related to, Service
Packs for your preinstalled Microsoft Windows product, refer to the Microsoft
Product Support Services Web site at http://www.support.microsoft.com/directory/,
or you can contact the Customer Support Center. Some fees might apply.
Purchasing additional services
During and after the warranty period, you can purchase additional services, such as
support for hardware, operating systems, and application programs; network setup
and configuration; upgraded or extended hardware repair services; and custom
installations. Service availability and service name might vary by country or region.
For more information about these services, go to the Lenovo Web site at
Lenovo product service
Appendix A. Getting help and technical assistance 59
Download from Www.Somanuals.com. All Manuals Search And Download.
60 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B. Notices
Lenovo may not offer the products, services, or features discussed in this document
in all countries. Consult your local Lenovo representative for information on the
products and services currently available in your area. Any reference to a Lenovo
product, program, or service is not intended to state or imply that only that Lenovo
product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any Lenovo intellectual property right may
be used instead. However, it is the user’s responsibility to evaluate and verify the
operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you any
license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF
ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow
disclaimer of express or implied warranties in certain transactions, therefore, this
statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. Lenovo may make improvements
and/or changes in the product(s) and/or the program(s) described in this publication
at any time without notice.
The products described in this document are not intended for use in implantation or
other life support applications where malfunction may result in injury or death to
persons. The information contained in this document does not affect or change
Lenovo product specifications or warranties. Nothing in this document shall operate
as an express or implied license or indemnity under the intellectual property rights
of Lenovo or third parties. All information contained in this document was obtained
in specific environments and is presented as an illustration. The result obtained in
other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for this
Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments may
vary significantly. Some measurements may have been made on development-level
systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been
© Lenovo 2008. Portions © IBM Corp. 2008.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
estimated through extrapolation. Actual results may vary. Users of this document
should verify the applicable data for their specific environment.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries,
or both:
Lenovo
Lenovo logo
ThinkServer
The following terms are trademarks of International Business Machines Corporation
in the United States, other countries, or both:
IBM
Wake on LAN
ServeRAID
Intel is a trademark or registered trademarks of Intel Corporation in the United
States, other countries, or both.
Microsoft and Windows are trademarks of Microsoft Corporation in the United
States, other countries, or both.
Adobe and PostScript are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States, other countries, or both.
Other company, product, or service names may be trademarks or service marks of
others.
Important notes
Processor speed indicates the internal clock speed of the microprocessor; other
factors also affect application performance.
CD or DVD drive speed is the variable read rate. Actual speeds vary and are often
less than the possible maximum.
When referring to processor storage, real and virtual storage, or channel volume,
KB stands for 1024 bytes, MB stands for 1 048 576 bytes, and GB stands for
1 073 741 824 bytes.
When referring to hard disk drive capacity or communications volume, MB stands
for 1 000 000 bytes, and GB stands for 1 000 000 000 bytes. Total user-accessible
capacity can vary depending on operating environments.
Maximum internal hard disk drive capacities assume the replacement of any
standard hard disk drives and population of all hard disk drive bays with the largest
currently supported drives that are available from Lenovo.
Maximum memory might require replacement of the standard memory with an
optional memory module.
Lenovo makes no representation or warranties regarding non-Lenovo products and
services, including but not limited to the implied warranties of merchantability and
fitness for a particular purpose. These products are offered and warranted solely by
third parties.
62 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Lenovo makes no representations or warranties with respect to non-Lenovo
products. Support (if any) for the non-Lenovo products is provided by the third party,
not Lenovo.
Some software might differ from its retail version (if available) and might not include
user manuals or all program functionality.
Waste electrical and electronic equipment (WEEE) notices
This unit must be recycled or discarded according to applicable local and national
regulations. Lenovo encourages owners of information technology (IT) equipment to
responsibly recycle their equipment when it is no longer needed. Lenovo offers a
variety of programs and services to assist equipment owners in recycling their IT
products. Information on Lenovo product recycling offerings can be found on
Esta unidad debe reciclarse o desecharse de acuerdo con lo establecido en la
normativa nacional o local aplicable. Lenovo recomienda a los propietarios de
equipos de tecnología de la información (TI) que reciclen responsablemente sus
equipos cuando éstos ya no les sean útiles. Lenovo dispone de una serie de
programas y servicios de devolución de productos, a fin de ayudar a los
propietarios de equipos a reciclar sus productos de TI. Se puede encontrar
información sobre las ofertas de reciclado de productos de Lenovo en el sitio web
Notice: This mark applies only to countries within the European Union (EU) and
Norway.
This appliance is labeled in accordance with European Directive 2002/96/EC
concerning waste electrical and electronic equipment (WEEE). The Directive
determines the framework for the return and recycling of used appliances as
applicable throughout the European Union. This label is applied to various products
to indicate that the product is not to be thrown away, but rather reclaimed upon end
of life per this Directive.
Remarque : Cette marque s’applique uniquement aux pays de l’Union Européenne
et à la Norvège.
L’etiquette du système respecte la Directive européenne 2002/96/EC en matière de
Déchets des Equipements Electriques et Electroniques (DEEE), qui détermine les
dispositions de retour et de recyclage applicables aux systèmes utilisés à travers
Appendix B. Notices 63
Download from Www.Somanuals.com. All Manuals Search And Download.
l’Union européenne. Conformément à la directive, ladite étiquette précise que le
produit sur lequel elle est apposée ne doit pas être jeté mais être récupéré en fin
de vie.
In accordance with the European WEEE Directive, electrical and electronic
equipment (EEE) is to be collected separately and to be reused, recycled, or
recovered at end of life. Users of EEE with the WEEE marking per Annex IV of the
WEEE Directive, as shown above, must not dispose of end of life EEE as unsorted
municipal waste, but use the collection framework available to customers for the
return, recycling, and recovery of WEEE. Customer participation is important to
minimize any potential effects of EEE on the environment and human health due to
the potential presence of hazardous substances in EEE. For proper collection and
treatment, contact your local Lenovo representative.
Battery return program
This product may contain a lithium or lithium ion battery. Consult your user manual
or service manual for specific battery information. The battery must be recycled or
disposed of properly. Recycling facilities may not be available in your area. For
information on disposal or batteries outside the United States, go to
facility.
For Taiwan: Please recycle batteries.
For the European Union:
Notice: This mark applies only to countries within the European Union (EU).
Batteries or packaging for batteries are labeled in accordance with European
Directive 2006/66/EC concerning batteries and accumulators and waste batteries
and accumulators. The Directive determines the framework for the return and
recycling of used batteries and accumulators as applicable throughout the European
Union. This label is applied to various batteries to indicate that the battery is not to
be thrown away, but rather reclaimed upon end of life per this Directive.
Les batteries ou emballages pour batteries sont étiquetés conformément aux
directives européennes 2006/66/EC, norme relative aux batteries et accumulateurs
en usage et aux batteries et accumulateurs usés. Les directives déterminent la
marche à suivre en vigueue dans l'Union Européenne pour le retour et le recyclage
des batteries et accumulateurs usés. Cette étiquette est appliquée sur diverses
batteries pour indiquer que la batterie ne doit pas être mise au rebut mais plutôt
récupérée en fin de cycle de vie selon cette norme.
In accordance with the European Directive 2006/66/EC, batteries and accumulators
are labeled to indicate that they are to be collected separately and recycled at end
of life. The label on the battery may also include a chemical symbol for the metal
64 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
concerned in the battery (Pb for lead, Hg for mercury, and Cd for cadmium). Users
of batteries and accumulators must not dispose of batteries and accumulators as
unsorted municipal waste, but use the collection framework available to customers
for the return, recycling, and treatment of batteries and accumulators. Customer
participation is important to minimize any potential effects of batteries and
accumulators on the environment and human health due to the potential presence
of hazardous substances. For proper collection and treatment, go to
For California:
hazardouswaste/perchlorate/.
The foregoing notice is provided in accordance with California Code of Regulations
Title 22, Division 4.5 Chapter 33. Best Management Practices for Perchlorate
Materials. This product/part may include a lithium manganese dioxide battery which
contains a perchlorate substance.
German Ordinance for Work gloss statement
The product is not suitable for use with visual display work place devices according
to clause 2 of the German Ordinance for Work with Visual Display Units.
Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne § 2 der
Bildschirmarbeitsverordnung geeignet.
Electronic emissions notices
Federal Communications Commission (FCC) statement
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the
interference at his own expense.
Properly shielded and grounded cables and connectors must be used in order to
meet FCC emission limits. Lenovo is not responsible for any radio or television
interference caused by using other than recommended cables and connectors or by
unauthorized changes or modifications to this equipment. Unauthorized changes or
modifications could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Industry Canada Class A emission compliance statement
This Class A digital apparatus complies with Canadian ICES-003.
Appendix B. Notices 65
Download from Www.Somanuals.com. All Manuals Search And Download.
Avis de conformité à la réglementation d'Industrie Canada
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
Australia and New Zealand Class A statement
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
United Kingdom telecommunications safety requirement
Notice to Customers
This apparatus is approved under approval number NS/G/1234/J/100003 for indirect
connection to public telecommunication systems in the United Kingdom.
European Union EMC Directive conformance statement
This product is in conformity with the protection requirements of EU Council
Directive 2004/108/EC on the approximation of the laws of the Member States
relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any
failure to satisfy the protection requirements resulting from a non-recommended
modification of the product, including the fitting of non-Lenovo option cards
This product has been tested and found to comply with the limits for Class A
Information Technology Equipment according to CISPR 22/European Standard EN
55022. The limits for Class A equipment were derived for commercial and industrial
environments to provide reasonable protection against interference with licensed
communication equipment.
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
German Class A compliance statement
Deutschsprachiger EU Hinweis:
Hinweis für Geräte der Klasse A EU-Richtlinie zur Elektromagnetischen
Verträglichkeit
Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG
(früher 89/336/EWG) zur Angleichung der Rechtsvorschriften über die
elektromagnetische Verträglichkeit in den EU-Mitgliedsstaaten und hält die
Grenzwerte der EN 55022 Klasse A ein.
Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu
installieren und zu betreiben. Des Weiteren dürfen auch nur von der Lenovo
empfohlene Kabel angeschlossen werden. Lenovo übernimmt keine Verantwortung
für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung
der Lenovo verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern
ohne Empfehlung der Lenovo gesteckt/eingebaut werden.
Deutschland:
66 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von
Betriebsmittein
Dieses Produkt entspricht dem “Gesetz über die elektromagnetische Verträglichkeit
von Betriebsmitteln” EMVG (früher “Gesetz über die elektromagnetische
Verträglichkeit von Geräten”). Dies ist die Umsetzung der EU-Richtlinie
2004/108/EG (früher 89/336/EWG) in der Bundesrepublik Deutschland.
Zulassungsbescheinigung laut dem Deutschen Gesetz über die
elektromagnetische Verträglichkeit von Betriebsmitteln, EMVG vom 20. Juli
2007 (früher Gesetz über die elektromagnetische Verträglichkeit von Geräten),
bzw. der EMV EG Richtlinie 2004/108/EC (früher 89/336/EWG), für Geräte der
Klasse A.
Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das
EG-Konformitätszeichen - CE - zu führen. Verantwortlich für die
Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo (Deutschland)
GmbH, Gropiusplatz 10, D-70563 Stuttgart.
Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4:
Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022
Klasse A.
Nach der EN 55022: “Dies ist eine Einrichtung der Klasse A. Diese Einrichtung
kann im Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom
Betreiber verlangt werden, angemessene Maßnahmen durchzuführen und dafür
aufzukommen.”
Nach dem EMVG: “Geräte dürfen an Orten, für die sie nicht ausreichend entstört
sind, nur mit besonderer Genehmigung des Bundesministers für Post und
Telekommunikation oder des Bundesamtes für Post und Telekommunikation
betrieben werden. Die Genehmigung wird erteilt, wenn keine elektromagnetischen
Störungen zu erwarten sind.” (Auszug aus dem EMVG, Paragraph 3, Abs. 4).
Dieses Genehmigungsverfahren ist nach Paragraph 9 EMVG in Verbindung mit der
entsprechenden Kostenverordnung (Amtsblatt 14/93) kostenpflichtig.
Anmerkung: Um die Einhaltung des EMVG sicherzustellen sind die Geräte, wie in
den Handbüchern angegeben, zu installieren und zu betreiben.
Japanese Voluntary Control Council for Interference (VCCI) statement
Appendix B. Notices 67
Download from Www.Somanuals.com. All Manuals Search And Download.
I
P
power
installing
integrated
power-control
power-on self-test (POST)
problems
L
LED
LEDs
M
R
memory
riser card
memory module
microprocessor
S
SAS
SATA
N
serial-attached SCSI
server
O
70 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
system board
T
U
utility program
V
W
web site
Web site
Index 71
Download from Www.Somanuals.com. All Manuals Search And Download.
72 ThinkServer RS110 Types 6435, 6436, 6437, and 6438: Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number: 46U0855
Printed in USA
(1P) P/N: 46U0855
Download from Www.Somanuals.com. All Manuals Search And Download.
|