Lenovo Personal Computer A50 User Manual

ThinkCentre™  
ꢀꢁꢂ  
User Guide  
Types 8084, 8085, 8126, 8147  
Types 8148, 8149, 8174, 8175  
Types 8176, 8177, 8178, 8179  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ThinkCentre™  
ꢀꢁꢂ  
User Guide  
Types 8084, 8085, 8126, 8147  
Types 8148, 8149, 8174, 8175  
Types 8176, 8177, 8178, 8179  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note  
Before using this information and the product it supports, be sure to read the “Important safety information” on page v and  
Third Edition (May 2004)  
© Copyright International Business Machines Corporation 2004. All rights reserved.  
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract  
with IBM Corp.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
© Copyright IBM Corp. 2004  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
iv User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important safety information  
This information can help you safely use your IBM® personal computer. Follow  
and retain all information included with your IBM computer. The information in  
this document does not alter the terms of your purchase agreement or the IBM  
Statement of Limited Warranty.  
Customer safety is important to IBM. Our products are developed to be safe and  
effective. However, personal computers are electronic devices. Power cords, power  
adapters, and other features can create potential safety risks that can result in  
physical injury or property damage, especially if misused. To reduce these risks,  
follow the instructions included with your product, observe all warnings on the  
product and in the operating instructions, and review the information included in  
this document carefully. By carefully following the information contained in this  
document and provided with your product, you can help protect yourself from  
hazards and create a safer computer work environment.  
Note: This information includes references to power adapters and batteries. In  
addition to mobile personal computers, IBM ships some products (such as speakers  
or monitors) with external power adapters. If you have such a product, this  
information applies to your product. In addition, your computer product may  
contain a coin-sized internal battery that provides power to your system clock even  
when the machine is unplugged, so the battery safety information applies to all  
computers.  
Conditions that require immediate action  
Products can become damaged due to misuse or neglect. Some product damage  
is serious enough that the product should not be used again until it has been  
inspected and, if necessary, repaired by an authorized servicer.  
As with any electronic device, pay close attention to the product when it is  
turned on. On very rare occasions, you might notice an odor or see a puff of  
smoke or sparks vent from your machine. Or you might hear sounds like  
popping, cracking or hissing. These conditions might merely mean that an  
internal electronic component has failed in a safe and controlled manner. Or,  
they might indicate a potential safety issue. However, do not take risks or  
attempt to diagnose the situation yourself.  
Frequently inspect your computer and its components for damage or wear or  
signs of danger. If you have any question about the condition of a component,  
do not use the product. Contact the IBM Support Center or the product  
manufacturer for instructions on how to inspect the product and have it  
repaired, if necessary.  
In the unlikely event that you notice any of the conditions listed below, or if  
you have any safety concerns with your product, stop using the product and  
unplug it from the power source and telecommunication lines until you can  
speak to the IBM Support Center for further guidance.  
v Power cords, plugs, power adapters, extension cords, surge protectors, or power  
supplies that are cracked, broken or damaged.  
v Signs of overheating, smoke, sparks or fire.  
© Copyright IBM Corp. 2004  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
v Damage to a battery (such as cracks, dents, creases), discharge from a battery, or  
a buildup of foreign substances on the battery.  
v A cracking, hissing or popping sound, or strong odor that comes from the  
product.  
v Signs that liquid has been spilled or an object has fallen onto the computer  
product, the power cord or power adapter.  
v The computer product, the power cord or power adapter has been exposed to  
water.  
v The product has been dropped or damaged in any way.  
v The product does not operate normally when you follow the operating  
instructions.  
Note: If you notice these conditions with a non-IBM product (such as an extension  
cord), stop using that product until you can contact the product manufacturer for  
further instructions, or until you get a suitable replacement.  
General safety guidelines  
Always observe the following precautions to reduce the risk of injury and property  
damage.  
Service  
Do not attempt to service a product yourself unless instructed to do so by the IBM  
Support Center. Use only an IBM authorized service provider who is approved to  
repair your particular product.  
Note: Some parts can be upgraded or replaced by the customer. These parts are  
referred to as Customer Replaceable Units, or CRUs. IBM expressly identifies CRUs  
as such, and provides documentation with instructions when it is appropriate for  
customers to replace those parts. You must closely follow all instructions when  
performing such replacements. Always make sure that the power is turned off and  
that the product is unplugged from any power source before you attempt the  
replacement. If you have any questions or concerns, contact the IBM Support  
Center.  
Power cords and power adapters  
Use only the power cords and power adapters supplied by the product  
manufacturer.  
Never wrap a power cord around the power adapter or other object. Doing so can  
stress the cord in ways that can cause the cord to fray, crack or crimp. This can  
present a safety hazard.  
Always route power cords so that they will not be walked on, tripped over, or  
pinched by objects.  
Protect the cord and power adapters from liquids. For instance, do not leave your  
cord or power adapter near sinks, tubs, toilets, or on floors that are cleaned with  
liquid cleansers. Liquids can cause a short circuit, particularly if the cord or power  
adapter has been stressed by misuse. Liquids can also cause gradual corrosion of  
the power cord terminals and/or the connector terminals on the adapter which can  
eventually result in overheating.  
vi User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Always connect power cords and signal cables in the correct order and ensure that  
all power cord connectors are securely and completely plugged into receptacles.  
Do not use any power adapter that shows corrosion at the ac input pins and/or  
shows signs of overheating (such as deformed plastic) at the ac input or anywhere  
on the power adapter.  
Do not use any power cords where the electrical contacts on either end show signs  
of corrosion or overheating or where the power cord appears to have been  
damaged in any way.  
Extension cords and related devices  
Ensure that extension cords, surge protectors, uninterruptible power supplies, and  
power strips that you use are rated to handle the electrical requirements of the  
product. Never overload these devices. If power strips are used, the load should  
not exceed the power strip input rating. Consult an electrician for more  
information if you have questions about power loads, power requirements, and  
input ratings.  
Plugs and outlets  
If a receptacle (power outlet) that you intend to use with your computer  
equipment appears to be damaged or corroded, do not use the outlet until it is  
replaced by a qualified electrician.  
Do not bend or modify the plug. If the plug is damaged, contact the manufacturer  
to obtain a replacement.  
Some products are equipped with a three-pronged plug. This plug fits only into a  
grounded electrical outlet. This is a safety feature. Do not defeat this safety feature  
by trying to insert it into a non-grounded outlet. If you cannot insert the plug into  
the outlet, contact an electrician for an approved outlet adapter or to replace the  
outlet with one that enables this safety feature. Never overload an electrical outlet.  
The overall system load should not exceed 80 percent of the branch circuit rating.  
Consult an electrician for more information if you have questions about power  
loads and branch circuit ratings.  
Be sure that the power outlet you are using is properly wired, easily accessible,  
and located close to the equipment. Do not fully extend power cords in a way that  
will stress the cords.  
Connect and disconnect the equipment from the electrical outlet carefully  
Batteries  
All IBM personal computers contain a non-rechargeable coin cell battery to provide  
power to the system clock. In addition many mobile products such as Thinkpad  
notebook PCs utilize a rechargeable battery pack to provide system power when in  
portable mode. Batteries supplied by IBM for use with your product have been  
tested for compatibility and should only be replaced with IBM approved parts.  
Never attempt to open or service any battery. Do not crush, puncture, or incinerate  
batteries or short circuit the metal contacts. Do not expose the battery to water or  
other liquids. Only recharge the battery pack strictly according to instructions  
included in the product documentation.  
Important safety information vii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Battery abuse or mishandling can cause the battery to overheat, which can cause  
gasses or flame to “vent” from the battery pack or coin cell. If your battery is  
damaged, or if you notice any discharge from your battery or the buildup of  
foreign materials on the battery leads, stop using the battery and obtain a  
replacement from the battery manufacturer.  
Batteries can degrade when they are left unused for long periods of time. For some  
rechargeable batteries (particularly Lithium Ion batteries), leaving a battery unused  
in a discharged state could increase the risk of a battery short circuit, which could  
shorten the life of the battery and can also pose a safety hazard. Do not let  
rechargeable Lithium-Ion batteries completely discharge or store these batteries in a  
discharged state.  
Heat and product ventilation  
Computers generate heat when turned on and when batteries are charging.  
Notebook PCs can generate a significant amount of heat due to their compact size.  
Always follow these basic precautions:  
v Do not leave the base of your computer in contact with your lap or any part of  
your body for an extended period when the computer is functioning or when  
the battery is charging. Your computer produces some heat during normal  
operation. Extended contact with the body could cause discomfort or, potentially,  
a skin burn.  
v Do not operate your computer or charge the battery near flammable materials or  
in explosive environments.  
v Ventilation slots, fans and/or heat sinks are provided with the product for safety,  
comfort, and reliable operation. These features might inadvertently become  
blocked by placing the product on a bed, sofa, carpet, or other flexible surface.  
Never block, cover or disable these features.  
CD and DVD drive safety  
CD and DVD drives spin discs at a high speed. If a CD or DVD is cracked or  
otherwise physically damaged, it is possible for the disc to break apart or even  
shatter when the CD drive is in use. To protect against possible injury due to this  
situation, and to reduce the risk of damage to your machine, do the following:  
v Always store CD/DVD discs in their original packaging  
v Always store CD/DVD discs out of direct sunlight and away from direct heat  
sources  
v Remove CD/DVD discs from the computer when not in use  
v Do not bend or flex CD/DVD discs, or force them into the computer or their  
packaging  
v Check CD/DVD discs for cracks before each use. Do not use cracked or  
damaged discs  
viii User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Additional safety information  
DANGER  
Electrical current from power, telephone, and communication cables is  
hazardous.  
To avoid a shock hazard:  
v Do not connect or disconnect any cables or perform installation, maintenance,  
or reconfiguration of this product during an electrical storm.  
v Connect all power cords to a properly wired and grounded electrical outlet.  
v Connect to properly wired outlets any equipment that will be attached to this  
product.  
v When possible, use one hand only to connect or disconnect signal cables.  
v Never turn on any equipment when there is evidence of fire, water, or  
structural damage.  
v Disconnect the attached power cords, telecommunications systems, networks,  
and modems before you open the device covers, unless instructed otherwise  
in the installation and configuration procedures.  
v Connect and disconnect cables as described in the following table when  
installing, moving, or opening covers on this product or attached devices.  
To connect:  
To disconnect:  
1. Turn everything OFF.  
2. First, attach all cables to devices.  
3. Attach signal cables to connectors.  
4. Attach power cords to outlet.  
5. Turn device ON.  
1. Turn everything OFF.  
2. First, remove power cords from outlet.  
3. Remove signal cables from connectors.  
4. Remove all cables from devices.  
DANGER  
Le courant électrique provenant de l’alimentation, du téléphone et des câbles de  
transmission peut présenter un danger.  
Pour éviter tout risque de choc électrique :  
v Ne manipulez aucun câble et n’effectuez aucune opération d’installation,  
d’entretien ou de reconfiguration de ce produit au cours d’un orage.  
v Branchez tous les cordons d’alimentation sur un socle de prise de courant  
correctement câblé et mis à la terre.  
v Branchez sur des socles de prise de courant correctement câblés tout  
équipement connecté à ce produit.  
v Lorsque cela est possible, n’utilisez qu’une seule main pour connecter ou  
déconnecter les câbles d’interface.;  
v Ne mettez jamais un équipement sous tension en cas d’incendie ou  
d’inondation, ou en présence de dommages matériels.  
v Avant de retirer les carters de l’unité, mettez celle-ci hors tension et  
déconnectez ses cordons d’alimentation, ainsi que les câbles qui la relient aux  
réseaux, aux systèmes de té lécommunication et aux modems (sauf instruction  
contraire mentionnée dans les procédures d’installation et de configuration).  
Important safety information ix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
v Lorsque vous installez, que vous déplacez, ou que vous manipulez le présent  
produit ou des périphériques qui lui sont raccordés, reportez-vous aux  
instructions ci-dessous pour connecter et déconnecter les différents cordons.  
Connexion:  
Déconnexion:  
1. Mettez les unités hors tension.  
1. Mettez les unités hors tension.  
2. Commencez par brancher tous les  
2. Débranchez les cordons d’alimentation  
cordons sur les unités.  
des prises.  
3. Branchez les câbles d’interface sur des  
3. Débranchez les câbles d’interface des  
connecteurs.  
connecteurs.  
4. Branchez les cordons d’alimentation sur 4. Débranchez tous les câbles des unités.  
des prises.  
5. Mettez les unités sous tension.  
Lithium battery notice  
CAUTION:  
Danger of explosion if battery is incorrectly replaced.  
When replacing the battery, use only IBM Part Number 33F8354 or an equivalent  
type battery recommended by the manufacturer. The battery contains lithium and  
can explode if not properly used, handled, or disposed of.  
Do not:  
v Throw or immerse into water  
v Heat to more than 100°C (212°F)  
v Repair or disassemble  
Dispose of the battery as required by local ordinances or regulations.  
ATTENTION  
Danger d’explosion en cas de remplacement incorrect de la batterie.  
Remplacer uniquement par une batterie IBM de type ou d’un type équivalent  
recommandé par le fabricant. La batterie contient du lithium et peut exploser en  
cas de mauvaise utilisation, de mauvaise manipulation ou de mise au rebut  
inappropriée.  
Ne pas :  
v Lancer ou plonger dans l’eau  
v Chauffer à plus de 100°C (212°F)  
v Réparer ou désassembler  
Mettre au rebut les batteries usagées conformément aux règlements locaux.  
Modem safety information  
To reduce the risk of fire, electrical shock, or injury when using telephone  
equipment, always follow basic safety precautions, such as:  
v Never install telephone wiring during a lightning storm.  
v Never install telephone jacks in wet locations unless the jack is specifically  
designed for wet locations.  
x
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
v Never touch uninsulated telephone wires or terminals unless the telephone line  
has been disconnected at the network interface.  
v Use caution when installing or modifying telephone lines.  
v Avoid using a telephone (other than a cordless type) during an electrical storm.  
There may be a remote risk of electric shock from lightning.  
v Do not use the telephone to report a gas leak in the vicinity of the leak.  
Consignes de sécurité relatives au modem  
Lors de l’utilisation de votre matériel téléphonique, il est important de respecter les  
consignes ci-après afin de réduire les risques d’incendie, d’électrocution et d’autres  
blessures :  
v N’installez jamais de cordons téléphoniques durant un orage.  
v Les prises téléphoniques ne doivent pas être installées dans des endroits  
humides, excepté si le modèle a été conçu à cet effet.  
v Ne touchez jamais un cordon téléphonique ou un terminal non isolé avant que  
la ligne ait été déconnectée du réseau téléphonique.  
v Soyez toujours prudent lorsque vous procédez à l’installation ou à la  
modification de lignes téléphoniques.  
v Si vous devez téléphoner pendant un orage, pour éviter tout risque de choc  
électrique, utilisez toujours un téléphone sans fil.  
v En cas de fuite de gaz, n’utilisez jamais un téléphone situé à proximité de la  
fuite.  
Laser compliance statement  
Some IBM Personal Computer models are equipped from the factory with a  
CD-ROM drive or a DVD-ROM drive. CD-ROM drives and DVD-ROM drives are  
also sold separately as options. CD-ROM drives and DVD-ROM drives are laser  
products. These drives are certified in the U.S. to conform to the requirements of  
the Department of Health and Human Services 21 Code of Federal Regulations  
(DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, these drives  
are certified to conform to the requirements of the International Electrotechnical  
Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.  
When a CD-ROM drive or a DVD-ROM drive is installed, note the following  
handling instructions.  
CAUTION:  
Use of controls or adjustments or performance of procedures other than those  
specified herein might result in hazardous radiation exposure.  
Removing the covers of the CD-ROM drive or DVD-ROM drive could result in  
exposure to hazardous laser radiation. There are no serviceable parts inside the  
CD-ROM drive or DVD-ROM drive. Do not remove the drive covers.  
Some CD-ROM drives and DVD-ROM drives contain an embedded Class 3A or  
Class 3B laser diode. Note the following statement.  
DANGER  
Laser radiation when open. Do not stare into the beam, do not view directly with optical  
instruments, and avoid direct exposure to the beam.  
Important safety information xi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DANGER:  
Certains modèles d’ordinateurs personnels sont équipés d’origine d’une unité de  
CD-ROM ou de DVD-ROM. Mais ces unités sont également vendues séparément  
en tant qu’options. L’unité de CD-ROM/DVD-ROM est un appareil à laser. Aux  
État-Unis, l’unité de CD-ROM/DVD-ROM est certifiée conforme aux normes  
indiquées dans le sous-chapitre J du DHHS 21 CFR relatif aux produits à laser de  
classe 1. Dans les autres pays, elle est certifiée être un produit à laser de classe 1  
conforme aux normes CEI 825 et CENELEC EN 60 825.  
Lorsqu’une unité de CD-ROM/DVD-ROM est installée, tenez compte des  
remarques suivantes:  
ATTENTION: Pour éviter tout risque d’exposition au rayon laser, respectez les  
consignes de réglage et d’utilisation des commandes, ainsi que les procédures  
décrites.  
L’ouverture de l’unité de CD-ROM/DVD-ROM peut entraîner un risque  
d’exposition au rayon laser. Pour toute intervention, faites appel à du personnel  
qualifié.  
Certaines unités de CD-ROM/DVD-ROM peuvent contenir une diode à laser de  
classe 3A ou 3B. Tenez compte de la consigne qui suit:  
DANGER  
Rayonnement laser lorsque le carter est ouvert. Évitez toute exposition directe des yeux  
au rayon laser. Évitez de regarder fixement le faisceau ou de l’observer à l’aide  
d’instruments optiques.  
xii User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Overview  
Thank you for selecting an IBM® computer. Your computer incorporates many of  
the latest advances in computer technology and can be upgraded as your needs  
change.  
This publication supports several computer models. Information in this section will  
help you identify your computer and help you find the chapter that contains  
information specific to your computer.  
Adding hardware options to your computer is an easy way to increase its  
capabilities. Instructions for installing external and internal options are included in  
this publication. When adding an option, use these instructions along with the  
instructions that come along with the option.  
Information resources  
The Quick Reference that comes with your computer provides information for  
installing your computer and starting the operating system. It also includes basic  
troubleshooting information, software recovery procedures, help and service  
information, and warranty information.  
Access IBM, on your desktop, provides a link to more information about your  
computer.  
If you have Internet access, the most up-to-date manuals for your computer are  
available from the World Wide Web. To access this information, point your browser  
to  
http://www.ibm.com/pc/support  
Type your machine type and model number in the Quick Path field, and click Go.  
© Copyright IBM Corp. 2004  
xiii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Identifying your computer  
xiv User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Chapter 1. Types 8149, 8177, and 8178  
This chapter provides an introduction to the features and options that are available  
for your computer. You can expand the capabilities of your computer by adding  
memory, adapters, or drives. When installing an option, use these instructions  
along with the instructions that come with the option.  
Important  
Before you install or remove any option, read “Important safety information”  
on page v. These precautions and guidelines will help you work safely.  
Features  
This section provides an overview of the computer features and preinstalled  
software.  
System information  
The following information covers a variety of models. For information for  
your specific model, use the IBM Setup Utility. See Chapter 4, “Using the IBM  
Microprocessor (varies by model type)  
v Intel® Pentium® 4 processor with HyperThreading Technology  
v Intel Pentium 4 processor  
v Intel Celeron® processor  
v Internal cache (size varies by model type)  
Memory  
v Support for four dual inline memory modules (DIMMs)  
v 512 KB flash memory for system programs  
Internal drives  
v 3.5-inch, 1.44 MB diskette drive  
v Internal hard disk drive  
© Copyright IBM Corp. 2004  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
v EIDE CD drive or DVD drive (some models)  
Video subsystem  
v An integrated graphics controller for a Video Graphics Array (VGA) monitor  
v Accelerated graphics port (AGP) video adapter slot on the system board (some  
models)  
Audio subsystem  
v AC’97 with ADI 1981B Audio Codec  
v Line in, line out, and microphone connectors on the rear panel  
Connectivity  
v 10/100 Mbps integrated Intel Ethernet controller that supports the Wake on  
LAN® feature  
v Soft modem V.90/V.44 (some models)  
System management features  
v Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)  
v Wake on LAN  
v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port  
Ring Detect for an external modem and Modem Ring Detect for an internal  
modem)  
v Remote Administration  
v Automatic power-on startup  
v System Management (SM) BIOS and SM software  
v Ability to store POST hardware test results  
Input/output features  
v 25-pin, Extended Capabilities Port (ECP)/Extended Parallel Port (EPP)  
v 9-pin serial connector  
v Six 4-pin, USB connectors (two on front panel and four on rear panel)  
v PS/2® mouse connector  
v PS/2 keyboard connector  
v Ethernet connector  
v VGA monitor connector  
v Three audio connectors (line in, line out, and microphone)  
Expansion  
v Four drive bays  
v Three 32-bit peripheral component interconnect (PCI) adapter slots  
Note: See “Installing adapters” on page 12 for supported card lengths.  
v One accelerated graphics port (AGP) expansion slot (some models)  
Power  
v 230 W power supply with manual voltage selection switch  
v Automatic 50/60 Hz input frequency switching  
v Advanced Power Management support  
v Advanced Configuration and Power Interface (ACPI) support  
2
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Security features  
v User and administrator passwords  
v Support for the addition of a rope clip and lockable cable  
v Support for the addition of an integrated cable lock  
v Startup sequence control  
v Startup without diskette drive, keyboard, or mouse  
v Unattended start mode  
v Diskette and hard disk I/O control  
v Serial and parallel port I/O control  
v Security profile by device  
IBM preinstalled software  
Your computer might come with preinstalled software. If it does, an operating  
system, device drivers to support built-in features, and other support programs are  
included.  
Operating systems (preinstalled) (varies by model type)  
Note: Not all countries or regions will have these operating systems.  
v Microsoft® Windows® XP Home  
v Microsoft Windows XP Professional  
Operating systems (certified or tested for compatibility)1  
v Microsoft Windows 2000  
v Linux2  
1. The operating systems listed here are being certified or tested for compatibility at the time this publication goes to press.  
Additional operating systems might be identified by IBM as compatible with your computer following the publication of this  
booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been certified or  
tested for compatibility, check the Web site of the operating system vendor.  
2. Linux certification http://www.ibm.com/pc/support/site.wss/migr-48nt8d.html  
Chapter 1. Types 8149, 8177, and 8178  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
 
Specifications  
This section lists the physical specifications for your computer.  
Heat output (approximate) in British thermal units (Btu)  
Dimensions  
per hour:  
Minimum configuration: 257 Btu/hr (75 watts)  
Maximum configuration: 785 Btu/hr (230 watts)  
Airflow  
Height: 140 mm (5.5 in.)  
Width: 425 mm (16.7 in.)  
Depth: 425 mm (16.7 in)  
Weight  
Approximately 0.51 cubic meters per minute (18 cubic  
feet per minute) maximum  
Minimum configuration as shipped: 10.0 kg (22 lb)  
Maximum configuration: 11.4 kg (25.0 lb)  
Acoustical noise-emission values  
Average sound-pressure levels:  
At operator position:  
Environment  
Air temperature:  
System on: 10° to 35°C (50° to 95° F)  
System off: 10° to 43°C (50° to 110° F)  
Idle: 30 dBA  
Operating: 32 dBA  
Maximum altitude: 2134 m (7000 ft)  
Note: The maximum altitude, 2134 m (7000 ft), is  
the maximum altitude at which the specified air  
temperatures apply. At higher altitudes, the  
maximum air temperatures are lower than those  
specified.  
At bystander position - 1 meter (3.3 ft):  
Idle: 26 dBA  
Operating: 30 dBA  
Declared (upper limit) sound-power levels:  
Idle: 4.0 bels  
Humidity:  
Operating: 4.3 bels  
System on: 8% to 80%  
System off: 8% to 80%  
Note: These levels were measured in controlled  
acoustical environments according to the procedures  
specified by the American National Standards  
Institute (ANSI) S12.10 and ISO 7779 and are reported  
in accordance with ISO 9296. Actual sound-pressure  
levels in a given location might exceed the average  
values stated because of room reflections and other  
nearby noise sources. The declared sound-power  
levels indicate an upper limit, below which a large  
number of computers will operate.  
Electrical input  
Input voltage:  
Low range:  
Minimum: 100 V ac  
Maximum: 127 V ac  
Input frequency range: 50-60 Hz  
Voltage switch setting: 115 V ac  
High range:  
Minimum: 200 V ac  
Maximum: 240 V ac  
Input frequency range: 50-60 Hz  
Voltage switch setting: 230 V ac  
Input kilovolt-amperes (kVA) (approximate):  
Minimum configuration as shipped: 0.08 kVA  
Maximum configuration: 0.3 kVA  
Note: Power consumption and heat output vary  
depending on the number and type of optional  
features installed and the power-management  
optional features in use.  
4
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Available options  
The following are some available options:  
v External options  
– Parallel port devices, such as printers and external drives  
– Serial port devices, such as external modems and digital cameras  
– Audio devices, such as external speakers for the sound system  
– USB devices, such as printers, joysticks, and scanners  
– Security device, such as a rope clip  
– Monitors  
v Internal options  
– System memory, called dual inline memory modules (DIMMs)  
– Peripheral component interconnect (PCI) adapters  
– Accelerated graphics port (AGP) adapters (some models)  
– Internal drives, such as:  
- CD drive or DVD drive (some models)  
- Hard disk drive  
- Diskette drives and other removable media drives  
For the latest information about available options, see the following World Wide  
Web pages:  
v http://www.ibm.com/pc/us/options/  
v http://www.ibm.com/pc/support/  
You can also obtain information by calling the following telephone numbers:  
v Within the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM  
reseller, or IBM marketing representative.  
v Within Canada, call 1-800-565-3344 or 1-800-IBM-4YOU.  
v Outside the United States and Canada, contact your IBM reseller or IBM  
marketing representative.  
Tools required  
To install some options in your computer, you might need a flat-blade or Phillips  
screwdriver. Additional tools might be needed for certain options. See the  
instructions that come with the option.  
Handling static-sensitive devices  
Static electricity, although harmless to you, can seriously damage computer  
components and options.  
When you add an option, do not open the static-protective package containing the  
option until you are instructed to do so.  
When you handle options and other computer components, take these precautions  
to avoid static electricity damage:  
v Limit your movement. Movement can cause static electricity to build up around  
you.  
v Always handle components carefully. Handle adapters and memory modules by  
the edges. Never touch any exposed circuitry.  
Chapter 1. Types 8149, 8177, and 8178  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
 
v Prevent others from touching components.  
v When you install a new option, touch the static-protective package containing  
the option to a metal expansion-slot cover or other unpainted metal surface on  
the computer for at least two seconds. This reduces static electricity in the  
package and your body.  
v When possible, remove the option and install it directly in the computer without  
setting the option down. When this is not possible, place the static-protective  
package that the option came in on a smooth, level surface and place the option  
on it.  
v Do not place the option on the computer cover or other metal surface.  
Installing external options  
This section shows the various external connectors on your computer to which you  
can attach external options, such as external speakers, a printer, or a scanner. For  
some external options, you must install additional software in addition to making  
the physical connection. When adding an external option, use the information in  
this section to identify the required connector, and then use the instructions that  
come with the option to help you make the connection and install any software or  
device drivers that are required for the option.  
Locating the connectors on the front of your computer  
The following illustration shows the locations of the connectors on the front of the  
computer.  
ꢀ1ꢁUSB connector  
ꢀ2ꢁUSB connector  
6
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Locating the connectors on the rear of your computer  
The following illustration shows the locations of the connectors on the rear of the  
computer.  
ꢀ1ꢁPower connector  
ꢀ2ꢁMouse connector  
ꢀ3ꢁParallel connector  
ꢀ4ꢁEthernet connector  
ꢀ5ꢁAudio line in connector  
ꢀ6ꢁPCI slots  
ꢀ8ꢁ Audio line out connector  
ꢀ9ꢁ Microphone connector  
ꢀ10ꢁUSB connectors  
ꢀ11ꢁVGA monitor connector  
ꢀ12ꢁSerial connector  
ꢀ13ꢁUSB connectors  
ꢀ7ꢁAGP slot (some models)  
ꢀ14ꢁKeyboard connector  
Note: Some connectors on the rear of the computer are color-coded to help you to  
determine where to connect the cables on your computer.  
Chapter 1. Types 8149, 8177, and 8178  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
 
Connector  
Description  
Mouse connector  
Used to attach a mouse, trackball, or other pointing device that  
uses a standard mouse connector.  
Parallel connector  
Ethernet connector  
Used to attach a parallel printer, parallel scanner, or other  
devices that use a 25-pin parallel connector.  
Used to attach an Ethernet cable for a local area network  
(LAN).  
Note: To operate the computer within FCC Class B limits, use  
a Category 5 Ethernet cable.  
Audio line in connector  
Audio line out connector  
Used to receive audio signals from an external audio device,  
such as a stereo system. When you attach an external audio  
device, a cable is connected between the audio line out  
connector of the device and the audio line in connector of the  
computer.  
Used to send audio signals from the computer to external  
devices, such as powered stereo speakers (speakers with  
built-in amplifiers), headphones, multimedia keyboards, or the  
audio line in connector on a stereo system or other external  
recording device.  
Microphone connector  
USB connectors  
Used to attach a microphone to your computer when you want  
to record voice or other sounds on the hard disk if you use  
speech-recognition software.  
Used to attach a device that requires a Universal Serial Bus  
(USB) connection, such as a USB scanner or USB printer. If you  
have more than six USB devices, you can purchase a USB hub,  
which you can use to connect additional USB devices.  
Serial connector  
Used to attach an external modem, serial printer, or other  
devices that use a 9-pin serial connector.  
Keyboard connector  
Used to attach a keyboard that uses a standard keyboard  
connector.  
Obtaining device drivers  
You can obtain device drivers for operating systems that are not preinstalled at  
http://www.ibm.com/pc/support/ on the World Wide Web. Installation  
instructions are provided in README files with the device-driver files.  
8
User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Removing the cover  
Important:  
static-sensitive devices” on page 5 before removing the cover.  
To remove the cover:  
1. Shut down your operating system, remove any media (diskettes, CDs, or tapes)  
from the drives, and turn off all attached devices and the computer.  
2. Unplug all power cords from electrical outlets.  
3. Disconnect all cables attached to the computer. This includes power cords,  
input/output (I/O) cables, and any other cables that are connected to the  
computer.  
4. Press the buttons on the sides of the computer and pivot the rear end of the  
cover up toward the front of the computer.  
Chapter 1. Types 8149, 8177, and 8178  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
 
Locating components  
The following illustration will help you locate the various components in your  
computer.  
ꢀ1ꢁCD drive or DVD drive  
ꢀ2ꢁUSB connector  
ꢀ3ꢁUSB connector  
ꢀ4ꢁOptional drive bay  
ꢀ5ꢁHard disk drive  
ꢀ6ꢁDiskette drive  
ꢀ7ꢁ DIMMs  
ꢀ8ꢁ Microprocessor and heat sink  
ꢀ9ꢁ AGP slot (some models)  
ꢀ10ꢁBattery  
ꢀ11ꢁPCI slots  
Identifying parts on the system board  
The system board (sometimes called the planar or motherboard) is the main circuit  
board in your computer. It provides basic computer functions and supports a  
variety of devices that are IBM-installed or that you can install later.  
10 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The following illustration shows the locations of parts on the system board.  
ꢀ1ꢁ Microprocessor  
ꢀ11ꢁ SATA0 connector  
ꢀ12ꢁ Front panel connector  
ꢀ13ꢁ Clear CMOS/Recovery jumper  
ꢀ14ꢁ Battery  
ꢀ15ꢁ Front panel audio connector  
ꢀ16ꢁ PCI slot 3  
ꢀ2ꢁ DIMM connector 1  
ꢀ3ꢁ DIMM connector 2  
ꢀ4ꢁ DIMM connector 3  
ꢀ5ꢁ DIMM connector 4  
ꢀ6ꢁ Power connector  
ꢀ7ꢁ Diskette drive connector  
ꢀ8ꢁ Primary IDE connector  
ꢀ9ꢁ Secondary IDE connector  
ꢀ10ꢁSATA1 connector  
ꢀ17ꢁ PCI slot 2  
ꢀ18ꢁ PCI slot 1  
ꢀ19ꢁ AGP slot (some models)  
ꢀ20ꢁ 12v power connector  
Installing memory  
Your computer has four connectors for installing dual inline memory modules  
(DIMMs) that provide up to a maximum of 4.0 GB of system memory.  
When installing DIMMs, the following rules apply:  
v System memory is divided into two channels (channel A and B). DIMM  
connectors 1 and 2 are channel A, and DIMM connectors 3 and 4 are channel B.  
v If DIMM connectors 1 and 3 (or 2 and 4) are filled with the same technology and  
size of memory, the system operates in dual channel mode.  
v Use 2.5 V, 184-pin, double data rate synchronous dynamic random access  
memory (DDR SDRAM).  
v Use 128 MB, 256 MB, 512 MB or 1.0 GB DIMMs in any combination.  
v DIMMs are 38.1 mm (1.5 inches) in height.  
Note: Only DDR SDRAM DIMMs can be used.  
Chapter 1. Types 8149, 8177, and 8178 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
To install a DIMM:  
2. You might have to remove an adapter to gain access to the DIMM slots. See  
3. To locate the DIMM connectors. See “Identifying parts on the system board” on  
4. Open the retaining clips.  
5. Make sure the notches in the DIMM align with the tabs on the connector. Push  
or insert the DIMM straight down into the connector until the retaining clips  
close.  
What to do next:  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Installing adapters  
This section provides information and instructions for installing and removing  
adapters. Your computer has three expansion slots for PCI adapters. One slot, used  
for an AGP adapter, is available on some models. You can install an adapter up to  
340 mm (13.4 inches) long in the AGP slot, PCI slot 2, or PCI slot 3. You can install  
an adapter up to 200 mm (7.9 inches) long in PCI slot 1.  
To install an adapter:  
12 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2. Remove the adapter-slot-cover latch and the slot cover for the appropriate  
expansion slot.  
3. Remove the adapter from its static-protective package.  
4. Install the adapter into the appropriate slot on the system board.  
5. Install the adapter-slot-cover latch.  
What to do next:  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Chapter 1. Types 8149, 8177, and 8178 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing internal drives  
This section provides information and instructions for installing and removing  
internal drives.  
Internal drives are devices that your computer uses to read and store data. You can  
add drives to your computer to increase storage capacity and to enable your  
computer to read other types of media. Some of the different drives that are  
available for your computer are:  
v Parallel Advanced Technology Attachment (PATA) hard disk drives  
v Serial ATA hard disk drives  
v CD drives or DVD drives  
v Tape drives  
v Removable media drives  
Note: These different drives are also referred to as integrated drive electronics  
(IDE) drives.  
Internal drives are installed in bays. In this book, the bays are referred to as bay 1,  
bay 2, and so on.  
When you install an internal drive, it is important to note what type and size of  
drive that you can install in each bay. Also, it is important to correctly connect the  
internal drive cables to the installed drive.  
Drive specifications  
Your computer comes with the following IBM-installed drives:  
v A CD drive or DVD drive in bay 1 (some models)  
v A 3.5-inch hard disk drive in bay 3  
v A 3.5-inch diskette drive in bay 4  
Any bay that does not have a drive installed has a static shield and bay panel  
installed.  
14 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The following illustration shows the locations of the drive bays.  
The following list describes some of the drives that you can install in each bay and  
their height requirements:  
ꢀ1ꢁ Bay 1 - Maximum height: 43.0 mm (1.7 in.)  
CD drive or DVD drive (preinstalled in  
some models)  
5.25-inch hard disk drive  
5.25-inch hard disk drive  
3.5-inch hard disk drive (requires a  
mounting bracket)  
ꢀ2ꢁ Bay 2 - Maximum height: 43.0 mm (1.7 in.)  
CD drive  
DVD drive  
ꢀ3ꢁ Bay 3 - Maximum height: 25.8 mm (1.0 in.)  
ꢀ4ꢁ Bay 4 - Maximum height: 25.8 mm (1.0 in.)  
3.5-inch hard disk drive (preinstalled)  
3.5-inch diskette drive (preinstalled)  
Notes:  
1. Drives that are greater than 43.0 mm (1.7 in.) high cannot be installed.  
2. Install removable media (tape or CD) drives in the accessible bay (bay 1 or 2).  
Installing a drive  
To install an internal drive, follow these steps:  
2. If your computer has a CD drive or DVD drive, you might need to remove the  
signal and power cables from the drive.  
3. If the drive you are installing is a removable-media drive, remove the bay  
panel from the front bezel.  
Chapter 1. Types 8149, 8177, and 8178 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Remove the metal shield from the drive bay by inserting a flat-blade  
screwdriver into one of the slots and gently prying it loose.  
5. Pivot the drive-bay latch handle toward the front of the computer and then  
pivot the drive-bay cage upward, as shown, until it is latched in the upright  
position.  
6. Make sure the drive that you are installing is set correctly as either a master or  
a slave device.  
Note: A serial ATA hard disk drive does not need to be set as either a master  
or a slave device.  
v If it is the first CD drive or DVD drive, set it as a master device.  
v If it is an additional CD drive or DVD drive, set it as a slave device.  
v If it is an additional parallel ATA hard disk drive, set it as a slave device.  
Refer to the documentation that comes with your drive for master/slave  
jumper information.  
16 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Install the drive into the bay. Align the screw holes and insert the two screws.  
8. Pivot the drive-bay cage back into place.  
9. A hard disk drive requires two cables; a power cable that connects to the power  
supply and a signal cable that connects to the system board.  
v A parallel ATA hard disk drive requires a four-wire power cable.  
v A serial ATA hard disk drive requires a five-wire power cable.  
The steps to connect a drive are different depending on the type of drive you are  
connecting. Use one of the following procedure for your drive connection.  
Connecting the first CD drive or DVD drive  
1. Locate the three-connector signal cable that comes with your computer or with  
the new drive.  
2. Locate the secondary IDE connector on the system board. See “Identifying parts  
Chapter 1. Types 8149, 8177, and 8178 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Connect one end of the signal cable to the drive and the other to the secondary  
IDE connector on the system board. To reduce electronic noise, use the  
connectors at the end of the cable only.  
4. Your computer has extra power connectors for additional drives. Connect a  
power connector to the drive.  
Connecting an additional CD drive, DVD drive, or parallel ATA  
hard disk drive  
1. Locate the secondary IDE connector on the system board and the  
three-connector signal cable. See “Identifying parts on the system board” on  
2. Connect the extra connector in the signal cable to the new drive.  
3. Your computer has extra power connectors for additional drives. Connect a  
power connector to the drive.  
Connecting a serial ATA hard disk drive  
A serial hard disk drive can be connected to any available SATA connector.  
1. Locate the signal cable that comes with the new drive.  
2. Locate an available SATA connector on the system board. See “Identifying parts  
3. Connect one end of the signal cable to the drive and the other to an available  
SATA connector on the system board.  
4. Your computer has extra power connectors for additional drives. Connect a  
power connector to the drive.  
What to do next  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Installing security features  
To help prevent hardware theft and unauthorized access to your computer, several  
security lock options are available. The following sections will help you identify  
and install the various types of locks that might be available for your computer. In  
addition to physical locks, unauthorized use of your computer can be prevented by  
a software lock that locks the keyboard until a correct password is typed in.  
Make sure that any security cables you install do not interfere with other computer  
cables.  
18 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Identifying security locks  
The following illustration shows the locations of the security features on the rear of  
the computer.  
ꢀ1ꢁ Rope clip  
ꢀ2ꢁ Integrated cable lock  
Rope clip  
Using a 3/16-inch or 5-mm rope clip (sometimes referred to as a U-bolt), a steel  
security cable, and a padlock can secure your computer to a desk, table, or other  
non-permanent fixture. For computers designed to accommodate the rope clip,  
knockouts at the rear of the chassis are provided.  
To install a rope clip:  
2. Use a tool, such as a screwdriver, to remove the two metal knockouts.  
3. Insert the rope clip through the rear panel; then attach and tighten the nuts  
with an appropriately sized or adjustable wrench.  
4. Replace the computer cover. For more information, see “Replacing the cover  
Chapter 1. Types 8149, 8177, and 8178 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Thread the cable through the rope clip and around an object that is not a part  
of or permanently secured to the building structure or foundation, and from  
which it cannot be removed; then fasten the cable ends together with a lock.  
®
20 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Integrated cable lock  
With an integrated cable lock (sometimes referred to as a Kensington lock), you  
can secure your computer to a desk, table, or other non-permanent fixture. The  
cable lock attaches to a security slot at the rear of your computer and is operated  
with a key. This is the same type of lock used with many laptop computers. You  
can order a cable lock directly from IBM. Go to http://www.pc.ibm.com/support  
and search on Kensington.  
®
Password protection  
To deter unauthorized use of your computer, you can use the IBM Setup Utility  
program to set a password. When you turn on your computer you are prompted to  
type the password to unlock the keyboard for normal use.  
What to do next:  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Changing the battery  
Your computer has a special type of memory that maintains the date, time, and  
settings for built-in features, such as parallel-port assignments (configuration). A  
battery keeps this information active when you turn off the computer.  
The battery normally requires no charging or maintenance throughout its life;  
however, no battery lasts forever. If the battery fails, the date, time, and  
configuration information (including passwords) are lost. An error message is  
displayed when you turn on the computer.  
Chapter 1. Types 8149, 8177, and 8178 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Refer to “Lithium battery notice” on page x for information about replacing and  
disposing of the battery.  
To change the battery:  
1. Turn off the computer and all attached devices.  
4. If necessary, remove any adapters that impede access to the battery. See  
5. Remove the old battery.  
6. Install the new battery.  
7. Replace any adapters that were removed to gain access to the battery. See  
“Installing adapters” on page 12 for instructions for replacing adapters.  
8. Replace the cover, and plug in the power cord. See “Replacing the cover and  
Note: When the computer is turned on for the first time after battery  
replacement, an error message might be displayed. This is normal after  
replacing the battery.  
9. Turn on the computer and all attached devices.  
10. Use the IBM Setup Utility program to set the date and time and any  
Erasing a lost or forgotten password (clearing CMOS)  
This section applies to lost or forgotten passwords. For more information about  
lost or forgotten passwords, see Access IBM on your desktop.  
To erase a forgotten password:  
1. Turn off the computer and all attached devices.  
3. Locate the Clear CMOS/Recovery jumper on the system board. See  
4. If necessary, see “Installing adapters” on page 12 to remove any adapters that  
impede access to the Clear CMOS/Recovery jumper.  
5. Move the jumper from the standard position (pins 1 and 2) to the  
maintenance or configure position (pins 2 and 3).  
22 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
6. Replace the cover and connect the power cord. See “Replacing the cover and  
7. Restart the computer, leave it on for approximately 10 seconds. Turn off the  
computer by holding the power switch for approximately 5 seconds. The  
computer will turn off.  
8. Repeat steps 2 through 4 on page 22.  
9. Move the jumper back to the standard (pins 1 and 2).  
10. Replace the cover and connect the power cord. See “Replacing the cover and  
Replacing the cover and connecting the cables  
After working with options, you need to install any removed parts, replace the  
cover, and reconnect any cables, including telephone lines and power cords. Also,  
depending on the option that is installed, you might need to confirm the updated  
information in the IBM Setup Utility program.  
To replace the cover and connect cables to your computer:  
1. Ensure that all components have been reassembled correctly and that no tools  
or loose screws are left inside your computer.  
2. Clear any cables that might impede the replacement of the cover.  
3. Position the cover over the chassis and pivot it down over the computer until it  
snaps into place.  
4. Reconnect the external cables and power cords to the computer. See “Installing  
5. To update the configuration, see Chapter 4, “Using the IBM Setup Utility  
Chapter 1. Types 8149, 8177, and 8178 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
24 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2. Types 8126, 8174, 8175, and 8176  
This chapter provides an introduction to the features and options that are available  
for your computer. You can expand the capabilities of your computer by adding  
memory, adapters, or drives. When installing an option, use these instructions  
along with the instructions that come with the option.  
Important  
Before you install or remove any option, read “Important safety information”  
on page v. These precautions and guidelines will help you work safely.  
Features  
This section provides an overview of the computer features and preinstalled  
software.  
System information  
The following information covers a variety of models. For information for  
your specific model, use the IBM Setup Utility. See Chapter 4, “Using the IBM  
Microprocessor (varies by model type)  
v Intel® Pentium® 4 processor with HyperThreading Technology  
v Intel Pentium 4 processor  
v Intel Celeron® processor  
v Internal cache (size varies by model type)  
Memory  
v Support for four dual inline memory modules (DIMMs)  
v 512 KB flash memory for system programs  
© Copyright IBM Corp. 2004  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Internal drives  
v 3.5-inch, 1.44 MB diskette drive  
v Internal hard disk drive  
v EIDE CD drive or DVD drive (some models)  
Video subsystem  
v An integrated graphics controller for a Video Graphics Array (VGA) monitor  
v Accelerated graphics port (AGP) video adapter slot on the system board (some  
models)  
Audio subsystem  
v AC’97 with ADI 1981B Audio Codec  
v Line in, line out, and microphone connectors on the rear panel  
Connectivity  
v 10/100 Mbps integrated Intel Ethernet controller that supports the Wake on  
LAN® feature  
v Soft modem V.90/V.44 (some models)  
System management features  
v Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)  
v Wake on LAN  
v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port  
Ring Detect for an external modem and Modem Ring Detect for an internal  
modem)  
v Remote Administration  
v Automatic power-on startup  
v System Management (SM) BIOS and SM software  
v Ability to store POST hardware test results  
Input/output features  
v 25-pin, Extended Capabilities Port (ECP)/Extended Parallel Port (EPP)  
v 9-pin serial connector  
v Six 4-pin, USB connectors (two on front panel and four on rear panel)  
v PS/2® mouse connector  
v PS/2 keyboard connector  
v Ethernet connector  
v VGA monitor connector  
v Three audio connectors (line in, line out, and microphone)  
Expansion  
v Four drive bays  
v Three 32-bit peripheral component interconnect (PCI) adapter slots  
Note: See “Installing adapters” on page 38 for supported card lengths.  
v One accelerated graphics port (AGP) expansion slot (some models)  
Power  
v 230 W power supply with manual voltage selection switch  
26 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
v Automatic 50/60 Hz input frequency switching  
v Advanced Power Management support  
v Advanced Configuration and Power Interface (ACPI) support  
Security features  
v User and administrator passwords  
v Support for the addition of a rope clip and lockable cable  
v Support for the addition of an integrated cable lock (see Access IBM)  
v Support for a padlock on the chassis  
v Startup sequence control  
v Startup without diskette drive, keyboard, or mouse  
v Unattended start mode  
v Diskette and hard disk I/O control  
v Serial and parallel port I/O control  
v Security profile by device  
IBM preinstalled software  
Your computer might come with preinstalled software. If it does, an operating  
system, device drivers to support built-in features, and other support programs are  
included.  
Operating systems preinstalled (varies by model type)  
Note: Not all countries or regions will have these operating systems.  
v Microsoft® Windows® XP Home  
v Microsoft Windows XP Professional  
Operating systems (certified or tested for compatibility)3  
v Microsoft Windows 2000  
v Linux4  
3. The operating systems listed here are being certified or tested for compatibility at the time this publication goes to press.  
Additional operating systems might be identified by IBM as compatible with your computer following the publication of this  
booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been certified or  
tested for compatibility, check the Web site of the operating system vendor.  
4. Linux certification http://www.ibm.com/pc/support/site.wss/migr-48nt8d.html  
Chapter 2. Types 8126, 8174, 8175, and 8176 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Specifications  
This section lists the physical specifications for your computer.  
Heat output (approximate) in British thermal units (Btu)  
Dimensions  
per hour:  
Minimum configuration: 257 Btu/hr (75 watts)  
Maximum configuration: 785 Btu/hr (230 watts)  
Airflow  
Height: 398 mm (15.67 in.)  
Width: 180 mm (7.08 in.)  
Depth: 402 mm (15.82 in.)  
Weight  
Approximately 0.68 cubic meters every minute (24  
cubic feet every minute) maximum  
Minimum configuration as shipped: 7.6 kg (16.8 lb)  
Maximum configuration: 9.97 kg (22 lb)  
Acoustical noise-emission values  
Environment  
Air temperature:  
For microprocessors less than 2.8 GHz:  
Average sound-pressure levels:  
At operator position:  
System on: 10° to 35°C (50° to 95° F)  
System off: 10° to 43°C (50° to 110° F)  
Maximum altitude: 2134 m (7000 ft)  
Note: The maximum altitude, 2134 m (7000 ft), is  
the maximum altitude at which the specified air  
temperatures apply. At higher altitudes, the  
maximum air temperatures are lower than those  
specified.  
Idle: 28 dBA  
Operating: 35 dBA  
At bystander position - 1 meter (3.3 ft):  
Idle: 25 dBA  
Operating: 33 dBA  
Humidity:  
Declared (upper limit) sound-power levels:  
Idle: 4.0 bels  
System on: 8% to 80%  
System off: 8% to 80%  
Operating: 4.7 bels  
Electrical input  
For microprocessors greater than or equal to 2.8 GHz:  
Average sound-pressure levels:  
At operator position:  
Input voltage:  
Low range:  
Minimum: 100 V ac  
Idle: 33 dBA  
Maximum: 127 V ac  
Operating: 35 dBA  
Input frequency range: 50–60 Hz  
Voltage switch setting: 115 V ac  
High range:  
At bystander position - 1 meter (3.3 ft):  
Idle: 30 dBA  
Operating: 33 dBA  
Minimum: 200 V ac  
Declared (upper limit) sound-power levels:  
Idle: 4.4 bels  
Maximum: 240 V ac  
Input frequency range: 50–60 Hz  
Voltage switch setting: 230 V ac  
Input kilovolt-amperes (kVA) (approximate):  
Minimum configuration as shipped: 0.08 kVA  
Maximum configuration: 0.30 kVA  
Operating: 4.7 bels  
Note: These levels were measured in controlled  
acoustical environments according to the procedures  
specified by the American National Standards Institute  
(ANSI) S12.10 and ISO 7779 and are reported in  
accordance with ISO 9296. Actual sound-pressure levels  
in a given location might exceed the average values  
stated because of room reflections and other nearby noise  
sources. The declared sound-power levels indicate an  
upper limit, below which a large number of computers  
will operate.  
Note: Power consumption and heat output vary  
depending on the number and type of optional  
features installed and the power-management  
optional features in use.  
28 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Available options  
The following are some available options:  
v External options  
– Parallel port devices, such as printers and external drives  
– Serial port devices, such as external modems and digital cameras  
– Audio devices, such as external speakers for the sound system  
– USB devices, such as printers, joysticks, and scanners  
– Security device, such as a rope clip  
– Monitors  
v Internal options  
– System memory, called dual inline memory modules (DIMMs)  
– Peripheral component interconnect (PCI) adapters  
– Accelerated graphics port (AGP) adapters (some models)  
– Internal drives, such as:  
- CD drive or DVD drive  
- Hard disk  
- Diskette drives and other removable media drives  
For the latest information about available options, see the following World Wide  
Web pages:  
v http://www.ibm.com/pc/us/options/  
v http://www.ibm.com/pc/support/  
You can also obtain information by calling the following telephone numbers:  
v Within the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM  
reseller, or IBM marketing representative.  
v Within Canada, call 1-800-565-3344 or 1-800-IBM-4YOU.  
v Outside the United States and Canada, contact your IBM reseller or IBM  
marketing representative.  
Tools required  
To install some options in your computer, you might need a flat-blade or Phillips  
screwdriver. Additional tools might be needed for certain options. See the  
instructions that come with the option.  
Handling static-sensitive devices  
Static electricity, although harmless to you, can seriously damage computer  
components and options.  
When you add an option, do not open the static-protective package containing the  
option until you are instructed to do so.  
When you handle options and other computer components, take these precautions  
to avoid static electricity damage:  
v Limit your movement. Movement can cause static electricity to build up around  
you.  
v Always handle components carefully. Handle adapters and memory modules by  
the edges. Never touch any exposed circuitry.  
Chapter 2. Types 8126, 8174, 8175, and 8176 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
v Prevent others from touching components.  
v When you install a new option, touch the static-protective package containing  
the option to a metal expansion-slot cover or other unpainted metal surface on  
the computer for at least two seconds. This reduces static electricity in the  
package and your body.  
v When possible, remove the option and install it directly in the computer without  
setting the option down. When this is not possible, place the static-protective  
package that the option came in on a smooth, level surface and place the option  
on it.  
v Do not place the option on the computer cover or other metal surface.  
Installing external options  
This section shows the various external connectors on your computer to which you  
can attach external options, such as external speakers, a printer, or a scanner. For  
some external options, you must install additional software in addition to making  
the physical connection. When adding an external option, use the information in  
this section to identify the required connector, and then use the instructions that  
come with the option to help you make the connection and install any software or  
device drivers that are required for the option.  
30 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Locating the connectors on the front of your computer  
The following illustration shows the locations of the USB connectors on the front of  
the computer.  
ꢀ1ꢁUSB connector  
ꢀ2ꢁUSB connector  
Chapter 2. Types 8126, 8174, 8175, and 8176 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Locating the connectors on the rear of your computer  
The following illustration shows the locations of the connectors on the back of the  
computer.  
ꢀ1ꢁ Power connector  
ꢀ2ꢁ Mouse connector  
ꢀ3ꢁ Keyboard connector  
ꢀ4ꢁ USB connectors  
ꢀ5ꢁ Serial connector  
ꢀ6ꢁ Parallel connector  
ꢀ7ꢁ VGA monitor connector  
ꢀ8ꢁ USB connectors  
ꢀ9ꢁ Ethernet connector  
ꢀ10ꢁMicrophone connector  
ꢀ11ꢁAudio line out connector  
ꢀ12ꢁAudio line in connector  
ꢀ13ꢁAGP slot (some models)  
ꢀ14ꢁPCI slots  
Note: Some connectors on the rear of the computer are color-coded to help you to  
determine where to connect the cables on your computer.  
32 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connector  
Description  
Mouse connector  
Used to attach a mouse, trackball, or other pointing device that  
uses a standard mouse connector.  
Keyboard connector  
USB connectors  
Used to attach a keyboard that uses a standard keyboard  
connector.  
Used to attach a device that requires a Universal Serial Bus  
(USB) connection, such as a USB scanner or USB printer. If you  
have more than six USB devices, you can purchase a USB hub,  
which you can use to connect additional USB devices.  
Serial connector  
Used to attach an external modem, serial printer, or other  
devices that use a 9-pin serial connector.  
Parallel connector  
Ethernet connector  
Used to attach a parallel printer, parallel scanner, or other  
devices that use a 25-pin parallel connector.  
Used to attach an Ethernet cable for a local area network  
(LAN).  
Note: To operate the computer within FCC Class B limits, use  
a Category 5 Ethernet cable.  
Microphone connector  
Used to attach a microphone to your computer when you want  
to record voice or other sounds on the hard disk if you use  
speech-recognition software.  
Audio line out connector  
Used to send audio signals from the computer to external  
devices, such as powered stereo speakers (speakers with  
built-in amplifiers), headphones, multimedia keyboards, or the  
audio line in connector on a stereo system or other external  
recording device.  
Audio line in connector  
Used to receive audio signals from an external audio device,  
such as a stereo system. When you attach an external audio  
device, a cable is connected between the audio line out  
connector of the device and the audio line in connector of the  
computer.  
Obtaining device drivers  
You can obtain device drivers for operating systems that are not preinstalled at  
http://www.ibm.com/pc/support/ on the World Wide Web. Installation  
instructions are provided in README files with the device-driver files.  
Chapter 2. Types 8126, 8174, 8175, and 8176 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Removing the cover  
Important  
static-sensitive devices” on page 29 before removing the cover.  
To remove the cover:  
1. Shut down your operating system, remove any media (diskettes, CDs, or tapes)  
from the drives, and turn off all attached devices and the computer.  
2. Unplug all power cords from electrical outlets.  
3. Disconnect all cables attached to the computer. This includes power cords,  
input/output (I/O) cables, and any other cables that are connected to the  
computer.  
4. Remove the two screws at the rear of the left side cover and slide the cover to  
the rear to remove.  
34 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Locating components  
The following illustration will help you locate the various components in your  
computer.  
ꢀ1ꢁMicroprocessor and heat sink  
ꢀ2ꢁDIMMs  
ꢀ3ꢁAGP slot (some models)  
ꢀ4ꢁPCI slots  
ꢀ5ꢁPCI adapter  
ꢀ6ꢁPower supply  
Identifying parts on the system board  
The system board (sometimes called the planar or motherboard) is the main circuit  
board in your computer. It provides basic computer functions and supports a  
variety of devices that are IBM-installed or that you can install later.  
Chapter 2. Types 8126, 8174, 8175, and 8176 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The following illustration shows the locations of parts on the system board.  
ꢀ1ꢁ Microprocessor  
ꢀ11ꢁ SATA0 connector  
ꢀ12ꢁ Front panel connector  
ꢀ13ꢁ Clear CMOS/Recovery jumper  
ꢀ14ꢁ Battery  
ꢀ15ꢁ Front panel audio connector  
ꢀ16ꢁ PCI slot 3  
ꢀ2ꢁ DIMM connector 1  
ꢀ3ꢁ DIMM connector 2  
ꢀ4ꢁ DIMM connector 3  
ꢀ5ꢁ DIMM connector 4  
ꢀ6ꢁ Power connector  
ꢀ7ꢁ Diskette drive connector  
ꢀ8ꢁ Primary IDE connector  
ꢀ9ꢁ Secondary IDE connector  
ꢀ10ꢁSATA1 connector  
ꢀ17ꢁ PCI slot 2  
ꢀ18ꢁ PCI slot 1  
ꢀ19ꢁ AGP slot (some models)  
ꢀ20ꢁ 12v power connector  
Installing memory  
Your computer has four connectors for installing dual inline memory modules  
(DIMMs) that provide up to a maximum of 4.0 GB of system memory.  
When installing DIMMs, the following rules apply:  
v System memory is divided into two channels (channel A and B). DIMM  
connectors 1 and 2 are channel A, and DIMM connectors 3 and 4 are channel B.  
v If DIMM connectors 1 and 3 (or 2 and 4) are filled with the same technology and  
size of memory, the system operates in dual channel mode.  
v Use 2.5 V, 184-pin, double data rate synchronous dynamic random access  
memory (DDR SDRAM).  
v Use 128 MB, 256 MB, 512 MB or 1.0 GB DIMMs in any combination.  
v DIMMs are 38.1 mm (1.5 inches) in height.  
Note: Only DDR SDRAM DIMMs can be used.  
36 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
To install a DIMM:  
2. You might have to remove an adapter to gain access to the DIMM slots. See  
3. Locate the DIMM connectors. See “Identifying parts on the system board” on  
4. Open the retaining clips.  
5. Make sure the notches in the DIMM align with the tabs on the connector. Push  
or insert the DIMM straight down into the connector until the retaining clips  
close.  
What to do next:  
v Replace any adapters that were removed.  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Chapter 2. Types 8126, 8174, 8175, and 8176 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing adapters  
This section provides information and instructions for installing and removing  
adapters. Your computer has three expansion slots for PCI adapters. One slot, used  
for an AGP adapter, is available on some models. You can install an adapter up to  
228 mm (9 inches) long in the AGP slot, PCI slot 2, or PCI slot 3. You can install an  
adapter up to 200 mm (7.9 inches) long in PCI slot 1.  
To install an adapter:  
2. Remove the adapter slot cover for the appropriate expansion slot.  
3. Remove the adapter from its static-protective package.  
4. Install the adapter into the appropriate slot on the system board.  
38 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Secure the adapter with the screw as shown.  
What to do next  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Installing internal drives  
This section provides information and instructions for installing and removing  
internal drives.  
Internal drives are devices that your computer uses to read and store data. You can  
add drives to your computer to increase storage capacity and to enable your  
computer to read other types of media. Some of the different drives that are  
available for your computer are:  
v Parallel Advanced Technology Attachment (PATA) hard disk drives  
v Serial ATA hard disk drives  
v CD drives or DVD drives  
v Removable media drives  
Note: These different drives are also referred to as integrated drive electronics  
(IDE) drives.  
Internal drives are installed in bays. In this book, the bays are referred to as bay 1,  
bay 2, and so on.  
When you install an internal drive, it is important to note what type and size of  
drive that you can install in each bay. Also, it is important to correctly connect the  
internal drive cables to the installed drive.  
Chapter 2. Types 8126, 8174, 8175, and 8176 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Drive specifications  
Your computer comes with the following IBM-installed drives:  
v A CD drive or DVD drive in bay 1  
v A 3.5-inch diskette disk drive in bay 3  
v A 3.5-inch hard drive in bay 4  
Any bay that does not have a drive installed has a static shield and bay panel  
installed.  
The following illustration shows the locations of the drive bays.  
The following table describes some of the drives you can install in each bay and  
their height requirements.  
ꢀ1ꢁBay 1 - Maximum height: 43.0 mm (1.7 in.) CD drive or DVD drive (preinstalled in  
some models)  
5.25-inch hard disk drive  
ꢀ2ꢁBay 2 - Maximum height: 43.0 mm (1.7 in.) 5.25-inch hard disk drive  
3.5-inch hard disk drive (requires a  
mounting bracket)  
CD drive  
DVD drive  
ꢀ3ꢁBay 3 - Maximum height: 25.8 mm (1.0 in.) 3.5-inch diskette drive (preinstalled)  
ꢀ4ꢁBay 4 - Maximum height: 25.8 mm (1.0 in.) 3.5-inch hard disk drive (preinstalled)  
Notes:  
1. Drives that are greater than 43.0 mm (1.7 in.) high cannot be installed.  
2. Install removable media (tape or CD) drives in the accessible bays (bay 1 or 2).  
40 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installing a drive  
To install an internal drive, follow these steps:  
2. If your computer has a CD drive or DVD drive, you might need to remove the  
signal and power cables from the drive.  
3. Remove the bay panel from the drive bay by inserting a flat-blade screwdriver  
at the end and gently prying it loose.  
4. Remove the metal shield from the drive bay by inserting a flat-blade  
screwdriver into one of the slots and gently prying it loose.  
5. Make sure the drive that you are installing is set correctly as either a master or  
a slave device.  
Note: A serial ATA hard disk drive does not need to be set as either a master  
or a slave device.  
v If it is the first CD drive or DVD drive, set it as a master device.  
v If it is an additional CD drive or DVD drive, set it as a slave device.  
v If it is an additional parallel ATA hard disk drive, set it as a slave device.  
Refer to the documentation that comes with your drive for master/slave  
jumper information.  
Chapter 2. Types 8126, 8174, 8175, and 8176 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
6. Install the drive into the bay. Align the screw holes and install two screws to  
secure the drive.  
7. A hard disk drive requires two cables; a power cable that connects to the power  
supply and a signal cable that connects to the system board.  
v A parallel ATA hard disk drive requires a four-wire power cable.  
v A serial ATA hard disk drive requires a five-wire power cable.  
The steps to connect a drive are different depending on the type of drive you are  
connecting. Use one of the following procedures for your drive connection.  
Connecting the first CD drive or DVD drive  
1. Locate the three-connector signal cable that comes with your computer or with  
the new drive.  
2. Locate the secondary IDE connector on the system board. See “Identifying parts  
3. Connect one end of the signal cable to the drive and the other to the secondary  
IDE connector on the system board. To reduce electronic noise, use the  
connectors at the end of the cable only.  
4. Your computer has extra power connectors for additional drives. Connect a  
power connector to the drive.  
42 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting an additional CD drive, DVD drive, or parallel ATA  
hard disk drive  
An additional drive can be connected to either the primary IDE or secondary IDE  
connector.  
1. Locate an available IDE connector on the three-connector signal cable attached  
to either the primary IDE or secondary IDE connector on the system board. See  
2. Connect the extra connector in the signal cable to the new drive.  
3. Your computer has extra power connectors for additional drives. Connect a  
power connector to the drive.  
Connecting a serial ATA hard disk drive  
A serial hard disk drive can be connected to any available SATA connector.  
1. Locate the signal cable that comes with the new drive.  
2. Locate an available SATA connector on the system board. See “Identifying parts  
3. Connect one end of the signal cable to the drive and the other to an available  
SATA connector on the system board.  
4. Your computer has extra power connectors for additional drives. Connect a  
power connector to the drive.  
What to do next  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Installing security features  
To help prevent hardware theft and unauthorized access to your computer, several  
security lock options are available. The following sections will help you identify  
and install the various types of locks that might be available for your computer. In  
addition to physical locks, unauthorized use of your computer can be prevented by  
a software lock that locks the keyboard until a correct password is typed in.  
Make sure that any security cables you install do not interfere with other computer  
cables.  
Chapter 2. Types 8126, 8174, 8175, and 8176 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Identifying security locks  
The following illustration shows the locations of the security features on the rear of  
the computer.  
ꢀ1ꢁ Rope clip  
ꢀ2ꢁ Integrated cable lock  
ꢀ3ꢁ Padlock loop  
Rope clip  
Using a 3/16-inch or 5-mm rope clip (sometimes referred to as a U-bolt), a steel  
security cable, and a padlock can secure your computer to a desk, table, or other  
non-permanent fixture. For computers designed to accommodate the rope clip,  
knockouts at the rear of the chassis are provided.  
To install a rope clip:  
2. Use a tool, such as a screwdriver, to remove the two metal knockouts.  
3. Insert the rope clip through the rear panel; then attach and tighten the nuts  
with an appropriately sized or adjustable wrench.  
4. Replace the computer cover. For more information, see “Replacing the cover  
44 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Thread the cable through the rope clip and around an object that is not a part  
of or permanently secured to the building structure or foundation, and from  
which it cannot be removed; then fasten the cable ends together with a lock.  
®
Chapter 2. Types 8126, 8174, 8175, and 8176 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Integrated cable lock  
With an integrated cable lock (sometimes referred to as a Kensington lock), you  
can secure your computer to a desk, table, or other non-permanent fixture. The  
cable lock attaches to a security slot at the rear of your computer and is operated  
with a key. This is the same type of lock used with many laptop computers. You  
can order a cable lock directly from IBM. Go to http://www.pc.ibm.com/support  
and search on Kensington.  
®
Password protection  
To deter unauthorized use of your computer, you can use the IBM Setup Utility  
program to set a password. When you turn on your computer you are prompted to  
type the password to unlock the keyboard for normal use.  
What to do next  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Changing the battery  
Your computer has a special type of memory that maintains the date, time, and  
settings for built-in features, such as parallel-port assignments (configuration). A  
battery keeps this information active when you turn off the computer.  
The battery normally requires no charging or maintenance throughout its life;  
however, no battery lasts forever. If the battery fails, the date, time, and  
46 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
configuration information (including passwords) are lost. An error message is  
displayed when you turn on the computer.  
Refer to “Lithium battery notice” on page x for information about replacing and  
disposing of the battery.  
To change the battery:  
1. Turn off the computer and all attached devices.  
2. Unplug the power cord and remove the cover. See “Removing the cover” on  
4. If necessary, remove any adapters that impede access to the battery. See  
5. Remove the old battery.  
6. Install the new battery.  
7. Replace any adapters that were removed to gain access to the battery. See  
“Installing adapters” on page 38 for instructions for replacing adapters.  
8. Replace the cover, and plug in the power cord. See “Replacing the cover and  
Note: When the computer is turned on for the first time after battery  
replacement, an error message might be displayed. This is normal after  
replacing the battery.  
9. Turn on the computer and all attached devices.  
10. Use the IBM Setup Utility program to set the date and time and any  
passwords.  
Erasing a lost or forgotten password (clearing CMOS)  
This section applies to lost or forgotten passwords. For more information about  
lost or forgotten passwords, go to Access IBM.  
To erase a forgotten password:  
1. Turn off the computer and all attached devices.  
3. Locate the Clear CMOS/Recovery jumper on the system board. See  
Chapter 2. Types 8126, 8174, 8175, and 8176 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. If necessary, see “Installing adapters” on page 38 to remove any adapters that  
impede access to the Clear CMOS/Recovery jumper.  
5. Move the jumper from the standard position (pins 1 and 2) to the  
maintenance or configure position (pins 2 and 3).  
6. Replace the cover and connect the power cord. See “Replacing the cover and  
7. Restart the computer, leave it on for approximately 10 seconds. Turn off the  
computer by holding the power switch for approximately 5 seconds. The  
computer will turn off.  
8. Repeat steps 2 through 4 on page 47..  
9. Move the jumper back to the standard (pins 1 and 2).  
10. Replace the cover and connect the power cord. See “Replacing the cover and  
Replacing the cover and connecting the cables  
After working with options, you need to install any removed parts, replace the  
cover, and reconnect any cables, including telephone lines and power cords. Also,  
depending on the option that is installed, you might need to confirm the updated  
information in the IBM Setup Utility program.  
To replace the cover and connect cables to your computer:  
1. Ensure that all components have been reassembled correctly and that no tools  
or loose screws are left inside your computer.  
2. Clear any cables that might impede the replacement of the cover.  
3. Position the cover on the chassis so that the guides on the top and bottom of  
the cover engage the chassis and push the cover to the closed position. Insert  
the screws that secure the cover.  
4. Reconnect the external cables and power cords to the computer. See “Installing  
48 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. To update the configuration, see Chapter 4, “Using the IBM Setup Utility  
Chapter 2. Types 8126, 8174, 8175, and 8176 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
50 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179  
This chapter provides an introduction to the features and options that are available  
for your computer. You can expand the capabilities of your computer by adding  
memory, adapters, or drives. When installing an option, use these instructions  
along with the instructions that come with the option.  
Important  
Before you install or remove any option, read “Important safety information”  
on page v. These precautions and guidelines will help you work safely.  
Features  
This section provides an overview of the computer features and preinstalled  
software.  
System information  
The following information covers a variety of models. For information for  
your specific model, use the IBM Setup Utility. See Chapter 4, “Using the IBM  
Microprocessor (varies by model type)  
v Intel® Pentium® 4 processor with HyperThreading Technology  
v Intel Pentium 4 processor  
v Intel Celeron® processor  
v Internal cache (size varies by model type)  
Memory  
v Support for four dual inline memory modules (DIMMs)  
© Copyright IBM Corp. 2004  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
v 512 KB flash memory for system programs  
Internal drives  
v 3.5-inch, 1.44 MB diskette drive  
v Internal hard disk drive  
v EIDE CD-ROM or DVD-ROM drive (some models)  
Video subsystem  
v An integrated graphics controller for a Video Graphics Array (VGA) monitor  
v Accelerated graphics port (AGP) video adapter slot on the system board (some  
models)  
Audio subsystem  
v AC’97 with ADI 1981B Audio Codec  
v Line in, line out, and microphone connectors on the rear panel  
Connectivity  
v 10/100 Mbps integrated Intel Ethernet controller that supports the Wake on  
LAN® feature  
v Soft modem V.90/V.44 (some models)  
System management features  
v Remote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)  
v Wake on LAN  
v Wake on Ring (in the IBM Setup Utility program, this feature is called Serial Port  
Ring Detect for an external modem and Modem Ring Detect for an internal  
modem)  
v Remote Administration  
v Automatic power-on startup  
v System Management (SM) BIOS and SM software  
v Ability to store POST hardware test results  
Input/output features  
v 25-pin, Extended Capabilities Port (ECP)/Extended Parallel Port (EPP)  
v 9-pin serial connector  
v Six 4-pin, USB connectors (two on front panel and four on rear panel)  
v PS/2® mouse connector  
v PS/2 keyboard connector  
v Ethernet connector  
v VGA monitor connector  
v Three audio connectors (line in, line out, and microphone)  
Expansion  
v Five drive bays  
v Three 32-bit peripheral component interconnect (PCI) adapter slots  
Note: See “Installing adapters” on page 63 for supported card lengths.  
v One accelerated graphics port (AGP) expansion slot (some models)  
52 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Power  
v 230 W power supply with manual voltage selection switch  
v Automatic 50/60 Hz input frequency switching  
v Advanced Power Management support  
v Advanced Configuration and Power Interface (ACPI) support  
Security features  
v User and administrator passwords  
v Support for the addition of a rope clip and lockable cable  
v Support for the addition of an integrated cable lock  
v Support for a padlock on the chassis  
v Startup sequence control  
v Startup without diskette drive, keyboard, or mouse  
v Unattended start mode  
v Diskette and hard disk I/O control  
v Serial and parallel port I/O control  
v Security profile by device  
IBM preinstalled software  
Your computer might come with preinstalled software. If it does, an operating  
system, device drivers to support built-in features, and other support programs are  
included.  
Operating systems preinstalled (varies by model type)  
Note: Not all countries or regions will have these operating systems.  
v Microsoft® Windows® XP Home  
v Microsoft Windows XP Professional  
Operating systems (certified or tested for compatibility)5  
v Microsoft Windows 2000  
v Linux6  
5. The operating systems listed here are being certified or tested for compatibility at the time this publication goes to press.  
Additional operating systems might be identified by IBM as compatible with your computer following the publication of this  
booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been certified or  
tested for compatibility, check the Web site of the operating system vendor.  
6. Linux certification http://www.ibm.com/pc/support/site.wss/migr-48nt8d.html  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Specifications  
This section lists the physical specifications for your computer.  
Heat output (approximate) in British thermal units (Btu)  
Dimensions  
per hour:  
Minimum configuration: 257 Btu/hr (75 watts)  
Maximum configuration: 785 Btu/hr (230 watts)  
Airflow  
Height: 413 mm (16.25 in.)  
Width: 191 mm (7.5 in.)  
Depth: 406 mm (16 in.)  
Weight  
Approximately 0.68 cubic meters per minute (24 cubic  
feet per minute) maximum  
Minimum configuration as shipped: 9.1 kg (20 lb)  
Maximum configuration: 11.4 kg (25.0 lb)  
Acoustical noise-emission values  
Average sound-pressure levels:  
At operator position:  
Environment  
Air temperature:  
System on: 10° to 35°C (50° to 95° F)  
System off: 10° to 43°C (50° to 110° F)  
Idle: 28 dBA  
Operating: 30 dBA  
Maximum altitude: 2134 m (7000 ft)  
Note: The maximum altitude, 2134 m (7000 ft), is  
the maximum altitude at which the specified air  
temperatures apply. At higher altitudes, the  
maximum air temperatures are lower than those  
specified.  
At bystander position - 1 meter (3.3 ft):  
Idle: 26 dBA  
Operating: 29 dBA  
Declared (upper limit) sound-power levels:  
Idle: 4.1 bels  
Humidity:  
Operating: 4.3 bels  
System on: 8% to 80%  
System off: 8% to 80%  
Note: These levels were measured in controlled  
acoustical environments according to the procedures  
specified by the American National Standards  
Institute (ANSI) S12.10 and ISO 7779 and are reported  
in accordance with ISO 9296. Actual sound-pressure  
levels in a given location might exceed the average  
values stated because of room reflections and other  
nearby noise sources. The declared sound-power  
levels indicate an upper limit, below which a large  
number of computers will operate.  
Electrical input  
Input voltage:  
Low range:  
Minimum: 100 V ac  
Maximum: 127 V ac  
Input frequency range: 50–60 Hz  
Voltage switch setting: 115 V ac  
High range:  
Minimum: 200 V ac  
Maximum: 240 V ac  
Input frequency range: 50–60 Hz  
Voltage switch setting: 230 V ac  
Input kilovolt-amperes (kVA) (approximate):  
Minimum configuration as shipped: 0.08 kVA  
Maximum configuration: 0.3 kVA  
Note: Power consumption and heat output vary  
depending on the number and type of optional  
features installed and the power-management  
optional features in use.  
54 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Available options  
The following are some available options:  
v External options  
– Parallel port devices, such as printers and external drives  
– Serial port devices, such as external modems and digital cameras  
– Audio devices, such as external speakers for the sound system  
– USB devices, such as printers, joysticks, and scanners  
– Security device, such as a rope clip  
– Monitors  
– IEEE 1394 devices (requires an IEEE 1394 adapter)  
v Internal options  
– System memory, called dual inline memory modules (DIMMs)  
– Peripheral component interconnect (PCI) adapters  
– Accelerated graphics port (AGP) adapters (some models)  
– Internal drives, such as:  
- CD drive and DVD drive  
- Hard disk drive  
- Diskette drives and other removable media drives  
For the latest information about available options, see the following World Wide  
Web pages:  
v http://www.ibm.com/pc/us/options/  
v http://www.ibm.com/pc/support/  
You can also obtain information by calling the following telephone numbers:  
v Within the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM  
reseller, or IBM marketing representative.  
v Within Canada, call 1-800-565-3344 or 1-800-IBM-4YOU.  
v Outside the United States and Canada, contact your IBM reseller or IBM  
marketing representative.  
Tools required  
To install some options in your computer, you might need a flat-blade or Phillips  
screwdriver. Additional tools might be needed for certain options. See the  
instructions that come with the option.  
Handling static-sensitive devices  
Static electricity, although harmless to you, can seriously damage computer  
components and options.  
When you add an option, do not open the static-protective package containing the  
option until you are instructed to do so.  
When you handle options and other computer components, take these precautions  
to avoid static electricity damage:  
v Limit your movement. Movement can cause static electricity to build up around  
you.  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
v Always handle components carefully. Handle adapters and memory modules by  
the edges. Never touch any exposed circuitry.  
v Prevent others from touching components.  
v When you install a new option, touch the static-protective package containing  
the option to a metal expansion-slot cover or other unpainted metal surface on  
the computer for at least two seconds. This reduces static electricity in the  
package and your body.  
v When possible, remove the option and install it directly in the computer without  
setting the option down. When this is not possible, place the static-protective  
package that the option came in on a smooth, level surface and place the option  
on it.  
v Do not place the option on the computer cover or other metal surface.  
Installing external options  
This section shows the various external connectors on your computer to which you  
can attach external options, such as external speakers, a printer, or a scanner. For  
some external options, you must install additional software in addition to making  
the physical connection. When adding an external option, use the information in  
this section to identify the required connector, and then use the instructions that  
come with the option to help you make the connection and install any software or  
device drivers that are required for the option.  
56 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Locating the connectors on the front of your computer  
The following illustration shows the locations of the connectors on the front of the  
computer.  
Note: Not all computer models will have the following connectors.  
ꢀ1ꢁIEEE 1394 connector  
ꢀ2ꢁMicrophone connector  
ꢀ3ꢁHeadphone connector  
ꢀ4ꢁUSB connector  
ꢀ5ꢁUSB connector  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Locating the connectors on the rear of your computer  
The following illustration shows the locations of the connectors on the back of the  
computer.  
ꢀ1ꢁPower connector  
ꢀ2ꢁMouse connector  
ꢀ3ꢁKeyboard connector  
ꢀ4ꢁUSB connectors  
ꢀ5ꢁSerial connector  
ꢀ6ꢁParallel connector  
ꢀ7ꢁVGA monitor connector  
ꢀ8ꢁ USB connectors  
ꢀ9ꢁ Ethernet connector  
ꢀ10ꢁMicrophone connector  
ꢀ11ꢁAudio line out connector  
ꢀ12ꢁAudio line in connector  
ꢀ13ꢁAGP slot (some models)  
ꢀ14ꢁPCI slots  
Note: Some connectors on the rear of the computer are color-coded to help you to  
determine where to connect the cables on your computer.  
58 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connector  
Description  
Mouse connector  
Used to attach a mouse, trackball, or other pointing device that  
uses a standard mouse connector.  
Keyboard connector  
USB connectors  
Used to attach a keyboard that uses a standard keyboard  
connector.  
Used to attach a device that requires a Universal Serial Bus  
(USB) connection, such as a USB scanner or USB printer. If you  
have more than six USB devices, you can purchase a USB hub,  
which you can use to connect additional USB devices.  
Serial connector  
Used to attach an external modem, serial printer, or other  
devices that use a 9-pin serial connector.  
Parallel connector  
Ethernet connector  
Used to attach a parallel printer, parallel scanner, or other  
devices that use a 25-pin parallel connector.  
Used to attach an Ethernet cable for a local area network  
(LAN).  
Note: To operate the computer within FCC Class B limits, use  
a Category 5 Ethernet cable.  
Microphone connector  
Used to attach a microphone to your computer when you want  
to record voice or other sounds on the hard disk if you use  
speech-recognition software.  
Audio line out connector  
Used to send audio signals from the computer to external  
devices, such as powered stereo speakers (speakers with  
built-in amplifiers), headphones, multimedia keyboards, or the  
audio line in connector on a stereo system or other external  
recording device.  
Audio line in connector  
Used to receive audio signals from an external audio device,  
such as a stereo system. When you attach an external audio  
device, a cable is connected between the audio line out  
connector of the device and the audio line in connector of the  
computer.  
Obtaining device drivers  
You can obtain device drivers for operating systems that are not preinstalled at  
http://www.ibm.com/pc/support/ on the World Wide Web. Installation  
instructions are provided in README files with the device-driver files.  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Removing the cover  
Important  
static-sensitive devices” on page 55 before removing the cover.  
To remove the cover:  
1. Shut down your operating system, remove any media (diskettes, CDs, or tapes)  
from the drives, and turn off all attached devices and the computer.  
2. Unplug all power cords from electrical outlets.  
3. Disconnect all cables attached to the computer. This includes power cords,  
input/output (I/O) cables, and any other cables that are connected to the  
computer.  
4. Press the cover-release button on the left side cover and remove the cover.  
60 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Locating components  
The following illustration will help you locate the various components in your  
computer.  
ꢀ1ꢁMicroprocessor and heat sink  
ꢀ2ꢁDIMMs  
ꢀ4ꢁPCI adapter  
ꢀ5ꢁPower supply  
ꢀ3ꢁAGP slot (some models)  
Identifying parts on the system board  
The system board (sometimes called the planar or motherboard) is the main circuit  
board in your computer. It provides basic computer functions and supports a  
variety of devices that are IBM-installed or that you can install later.  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The following illustration shows the locations of parts on the system board.  
ꢀ1ꢁ Microprocessor  
ꢀ11ꢁ SATA0 connector  
ꢀ12ꢁ Front panel connector  
ꢀ13ꢁ Clear CMOS/Recovery jumper  
ꢀ14ꢁ Battery  
ꢀ15ꢁ Front panel audio connector  
ꢀ16ꢁ PCI slot 3  
ꢀ2ꢁ DIMM connector 1  
ꢀ3ꢁ DIMM connector 2  
ꢀ4ꢁ DIMM connector 3  
ꢀ5ꢁ DIMM connector 4  
ꢀ6ꢁ Power connector  
ꢀ7ꢁ Diskette drive connector  
ꢀ8ꢁ Primary IDE connector  
ꢀ9ꢁ Secondary IDE connector  
ꢀ10ꢁSATA1 connector  
ꢀ17ꢁ PCI slot 2  
ꢀ18ꢁ PCI slot 1  
ꢀ19ꢁ AGP slot (some models)  
ꢀ20ꢁ 12v power connector  
Installing memory  
Your computer has four connectors for installing dual inline memory modules  
(DIMMs) that provide up to a maximum of 4.0 GB of system memory.  
When installing DIMMs, the following rules apply:  
v System memory is divided into two channels (channel A and B). DIMM  
connectors 1 and 2 are channel A, and DIMM connectors 3 and 4 are channel B.  
v If DIMM connectors 1 and 3 (or 2 and 4) are filled with the same technology and  
size of memory, the system operates in dual channel mode.  
v Use 2.5 V, 184-pin, double data rate synchronous dynamic random access  
memory (DDR SDRAM).  
v Use 128 MB, 256 MB, 512 MB or 1.0 GB DIMMs in any combination.  
v DIMMs are 38.1 mm (1.5 inches) in height.  
Note: Only DDR SDRAM DIMMs can be used.  
62 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
To install a DIMM:  
2. You might have to remove an adapter to gain access to the DIMM slots. See  
3. Locate the DIMM connectors. See “Identifying parts on the system board” on  
4. Open the retaining clips.  
5. Make sure the notches in the DIMM align with the tabs on the connector. Push  
or insert the DIMM straight down into the connector until the retaining clips  
close.  
What to do next:  
v Replace any adapters that were removed.  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Installing adapters  
This section provides information and instructions for installing and removing  
adapters. Your computer has three expansion slots for PCI adapters. One slot, used  
for an AGP adapter, is available on some models. You can install an adapter up to  
228 mm (9 inches) long in the AGP slot, PCI slot 2, or PCI slot 3. You can install an  
adapter up to 200 mm (7.9 inches) long in PCI slot 1.  
To install an adapter:  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2. Remove the adapter-slot-cover latch and the slot cover for the appropriate  
expansion slot.  
3. Remove the adapter from its static-protective package.  
4. Install the adapter into the appropriate slot on the system board.  
5. Install the adapter-slot-cover latch.  
What to do next  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
64 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing internal drives  
This section provides information and instructions for installing and removing  
internal drives.  
Internal drives are devices that your computer uses to read and store data. You can  
add drives to your computer to increase storage capacity and to enable your  
computer to read other types of media. Some of the different drives that are  
available for your computer are:  
v Parallel Advanced Technology Attachment (PATA) hard disk drives  
v Serial ATA hard disk drives  
v CD drives or DVD drives  
v Removable media drives  
Note: These different drives are also referred to as integrated drive electronics  
(IDE) drives.  
Internal drives are installed in bays. In this book, the bays are referred to as bay 1,  
bay 2, and so on.  
When you install an internal drive, it is important to note what type and size of  
drive that you can install in each bay. Also, it is important to correctly connect the  
internal drive cables to the installed drive.  
Drive specifications  
Your computer comes with the following IBM-installed drives:  
v A CD drive or DVD drive in bay 1 (some models)  
v A 3.5-inch diskette disk drive in bay 4  
v A 3.5-inch hard drive in bay 5  
Any bay that does not have a drive installed has a static shield and bay panel  
installed.  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The following illustration shows the locations of the drive bays.  
The following list describes some of the drives you can install in each bay and  
their height requirements:  
ꢀ1ꢁBay 1 - Maximum height: 43.0 mm (1.7 in.) CD drive or DVD drive (preinstalled in  
some models)  
5.25-inch hard disk drive  
ꢀ2ꢁBay 2 - Maximum height: 43.0 mm (1.7 in.) 5.25-inch hard disk drive  
3.5-inch hard disk drive (requires a  
mounting bracket)  
CD drive  
DVD drive  
ꢀ3ꢁBay 3 - Maximum height: 25.8 mm (1.0 in.) 3.5-inch hard disk drive  
ꢀ4ꢁBay 4 - Maximum height: 25.8 mm (1.0 in.) 3.5-inch diskette drive (preinstalled)  
ꢀ5ꢁBay 5 - Maximum height: 25.8 mm (1.0 in.) Hard disk drive (preinstalled)  
Notes:  
1. Drives that are greater than 43.0 mm (1.7 in.) high cannot be installed.  
2. Install removable media (tape or CD) drives in the accessible bays (bay 1 or 2).  
Installing a drive  
To install an internal drive, follow these steps:  
2. If your computer has a CD drive or DVD drive, you might need to remove the  
signal and power cables from the drive.  
3. Remove the bay panel from the drive bay by inserting a flat-blade screwdriver  
at the end and gently prying it loose.  
66 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Remove the metal shield from the drive bay by inserting a flat-blade  
screwdriver into one of the slots and gently prying it loose.  
5. Make sure the drive that you are installing is set correctly as either a master or  
a slave device.  
Note: A serial ATA hard disk drive does not need to be set as either a master  
or a slave device.  
v If it is the first CD drive or DVD drive, set it as a master device.  
v If it is an additional CD drive or DVD drive, set it as a slave device.  
v If it is an additional parallel ATA hard disk drive, set it as a slave device.  
Refer to the documentation that comes with your drive for master/slave  
jumper information.  
6. You might have to remove the bezel to install some drives. Remove the front  
bezel by pushing in on the blue plastic tab at the rear of the computer.  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Install the drive into the bay and lock it into position.  
Note: Some drives might require screws to secure the drive into the bay. If this  
is the case, align the screw holes, and insert the screws to secure the  
drive.  
8. A hard disk drive requires two cables; a power cable that connects to the power  
supply and a signal cable that connects to the system board.  
v A parallel ATA hard disk drive requires a four-wire power cable.  
v A serial ATA hard disk drive requires a five-wire power cable.  
The steps to connect a drive are different depending on the type of drive you are  
connecting. Use one of the following procedures for your drive connection.  
Connecting the first CD drive or DVD drive  
1. Locate the three-connector signal cable that comes with your computer or with  
the new drive.  
68 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Locate the secondary IDE connector on the system board. See “Identifying parts  
3. Connect one end of the signal cable to the drive and the other to the secondary  
IDE connector on the system board. To reduce electronic noise, use the  
connectors at the end of the cable only.  
4. Your computer has extra power connectors for additional drives. Connect a  
power connector to the drive.  
Connecting an additional CD drive, DVD drive, or parallel ATA  
hard disk drive  
An additional drive can be connected to either the primary IDE or secondary IDE  
connector.  
1. Locate an available IDE connector on the three-connector signal cable attached  
to either the primary IDE or secondary IDE connector on the system board. See  
2. Connect the extra connector in the signal cable to the new drive.  
3. Your computer has extra power connectors for additional drives. Connect a  
power connector to the drive.  
Connecting a serial ATA hard disk drive  
A serial hard disk drive can be connected to any available SATA connector.  
1. Locate the signal cable that comes with the new drive.  
2. Locate an available SATA connector on the system board. See “Identifying parts  
3. Connect one end of the signal cable to the drive and the other to an available  
SATA connector on the system board.  
4. Your computer has extra power connectors for additional drives. Connect a  
power connector to the drive.  
What to do next  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Installing security features  
To help prevent hardware theft and unauthorized access to your computer, several  
security lock options are available. The following sections will help you identify  
and install the various types of locks that might be available for your computer. In  
addition to physical locks, unauthorized use of your computer can be prevented by  
a software lock that locks the keyboard until a correct password is typed in.  
Make sure that any security cables you install do not interfere with other computer  
cables.  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Identifying security locks  
The following illustration shows the locations of the security features on the rear of  
the computer.  
ꢀ1ꢁ Rope clip  
ꢀ2ꢁ Integrated cable lock  
Rope clip  
Using a 3/16-inch or 5-mm rope clip (sometimes referred to as a U-bolt), a steel  
security cable, and a padlock can secure your computer to a desk, table, or other  
non-permanent fixture. For computers designed to accommodate the rope clip,  
knockouts at the rear of the chassis are provided.  
To install a rope clip:  
2. Use a tool, such as a screwdriver, to remove the two metal knockouts.  
3. Insert the rope clip through the rear panel; then attach and tighten the nuts  
with an appropriately sized or adjustable wrench.  
4. Replace the computer cover. For more information, see “Replacing the cover  
70 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Thread the cable through the rope clip and around an object that is not a part  
of or permanently secured to the building structure or foundation, and from  
which it cannot be removed; then fasten the cable ends together with a lock.  
®
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Integrated cable lock  
With an integrated cable lock (sometimes referred to as a Kensington lock), you  
can secure your computer to a desk, table, or other non-permanent fixture. The  
cable lock attaches to a security slot at the rear of your computer and is operated  
with a key. This is the same type of lock used with many laptop computers. You  
can order a cable lock directly from IBM. Go to http://www.pc.ibm.com/support  
and search on Kensington.  
®
Password protection  
To deter unauthorized use of your computer, you can use the IBM Setup Utility  
program to set a password. When you turn on your computer you are prompted to  
type the password to unlock the keyboard for normal use.  
What to do next  
v To work with another option, go to the appropriate section.  
v To complete the installation, go to “Replacing the cover and connecting the  
Changing the battery  
Your computer has a special type of memory that maintains the date, time, and  
settings for built-in features, such as parallel-port assignments (configuration). A  
battery keeps this information active when you turn off the computer.  
72 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The battery normally requires no charging or maintenance throughout its life;  
however, no battery lasts forever. If the battery fails, the date, time, and  
configuration information (including passwords) are lost. An error message is  
displayed when you turn on the computer.  
Refer to “Lithium battery notice” on page x for information about replacing and  
disposing of the battery.  
To change the battery:  
1. Turn off the computer and all attached devices.  
4. If necessary, remove any adapters that impede access to the battery. See  
5. Remove the old battery.  
6. Install the new battery.  
7. Replace any adapters that were removed to gain access to the battery. See  
“Installing adapters” on page 63 for instructions for replacing adapters.  
8. Replace the cover, and plug in the power cord. See “Replacing the cover and  
Note: When the computer is turned on for the first time after battery  
replacement, an error message might be displayed. This is normal after  
replacing the battery.  
9. Turn on the computer and all attached devices.  
10. Use the IBM Setup Utility program to set the date and time and any  
Erasing a lost or forgotten password (clearing CMOS)  
This section applies to lost or forgotten passwords. For more information about  
lost or forgotten passwords, see Access IBM on your desktop.  
To erase a forgotten password:  
1. Turn off the computer and all attached devices.  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Locate the Clear CMOS/Recovery jumper on the system board. See  
4. If necessary, see “Installing adapters” on page 63 to remove any adapters that  
impede access to the Clear CMOS/Recovery jumper.  
5. Move the jumper from the standard position (pins 1 and 2) to the  
maintenance or configure position (pins 2 and 3).  
6. Replace the cover and connect the power cord. See “Replacing the cover and  
7. Restart the computer, leave it on for approximately 10 seconds. Turn off the  
computer by holding the power switch for approximately 5 seconds. The  
computer will turn off.  
8. Repeat steps 2 through 4 on page 73.  
9. Move the jumper back to the standard (pins 1 and 2).  
10. Replace the cover and connect the power cord. See “Replacing the cover and  
Replacing the cover and connecting the cables  
After working with options, you need to install any removed parts, replace the  
cover, and reconnect any cables, including telephone lines and power cords. Also,  
depending on the option that is installed, you might need to confirm the updated  
information in the IBM Setup Utility program.  
To replace the cover and connect cables to your computer:  
1. Ensure that all components have been reassembled correctly and that no tools  
or loose screws are left inside your computer.  
2. Clear any cables that might impede the replacement of the cover.  
3. Position the cover on the chassis so that the rail guides on the bottom of the  
cover engage the rails and push the cover closed until it latches.  
74 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Reconnect the external cables and power cords to the computer. See “Installing  
5. To update the configuration, see Chapter 4, “Using the IBM Setup Utility  
Chapter 3. Types 8084, 8085, 8147, 8148, and 8179 75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
76 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4. Using the IBM Setup Utility program  
The IBM Setup Utility program is stored in the electrically erasable programmable  
read-only memory (EEPROM) of your computer. The IBM Setup Utility program is  
used to view and change the configuration settings of your computer, regardless of  
which operating system you are using. However, the operating-system settings  
might override any similar settings in the IBM Setup Utility program.  
Starting the IBM Setup Utility program  
To start the IBM Setup Utility program, do the following:  
1. If your computer is already on when you start this procedure, shut down the  
operating system and turn off the computer.  
2. Press and hold the F1 key then turn on the computer. When you hear the  
multiple beeps, release the F1 key.  
Note: If an administrator password has been set, the IBM Setup Utility  
program menu is not displayed until you type your password. See  
“Using passwords” for more information.  
The IBM Setup Utility might start automatically when POST detects that hardware  
has been removed or new hardware has been installed in your computer.  
Viewing and changing settings  
The IBM Setup Utility program menu lists items that identify system configuration  
topics.  
When working with the IBM Setup Utility program menu, you must use the  
keyboard. The keys used to perform various tasks are displayed at the bottom of  
each screen.  
Exiting from the IBM Setup Utility program  
When you finish viewing or changing settings, press Esc to return to the IBM  
Setup Utility program menu (you might have to press Esc several times). If you  
want to save the new settings, select Save Settings before you exit. Otherwise,  
your changes will not be saved.  
Using passwords  
You can use passwords to provide security for your computer and data. There are  
two kinds of passwords: a user password and an administrator password. You do  
not have to set a password of either type to use your computer. However, if you  
decide to set either one, read the following sections.  
User password  
The user password feature deters unauthorized persons from gaining access to  
your computer.  
© Copyright IBM Corp. 2004  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Administrator password  
Setting an administrator password deters unauthorized persons from changing  
configuration settings. If you are responsible for maintaining the settings of several  
computers, you might want to set an administrator password.  
After you set an administrator password, a password prompt is displayed each  
time you try to access the IBM Setup Utility program. If you type the wrong  
password, you will see an error message. If you type the wrong password three  
times, you must turn the computer off and start again.  
If both the user and administrator passwords are set, you can type either  
password. However, to change any configuration settings, you must use your  
administrator password.  
Setting, changing, and deleting a password  
To set, change, or delete a password, do the following:  
Note: A password can be any combination of up to seven characters (A- Z, a-z,  
and 0-9).  
1. Start the IBM Setup Utility program (see “Starting the IBM Setup Utility  
2. From the IBM Setup Utility program menu, select Security.  
3. Select Set Passwords. Read the information displayed on the right side of the  
screen.  
Using Security Profile by Device  
Security Profile by Device is used to enable or disable user access to the following  
devices:  
IDE controller  
When this feature is set to Disable, all devices connected to the  
IDE controller (such as hard disk drives or the CD-ROM drive)  
are disabled and will not be displayed in the system  
configuration.  
Diskette Drive Access  
Diskette Write Protect  
When this feature is set to Disable, the diskette drive cannot be  
accessed.  
When this feature is set to Enable, all diskettes are treated as if  
they are write-protected.  
To set Security Profile by Device, do the following:  
1. Start the IBM Setup Utility program (see “Starting the IBM Setup Utility  
2. From the IBM Setup Utility program menu, select Security.  
3. Select Security Profile by Device.  
4. Select the desired devices and settings and press Enter.  
5. Return to the IBM Setup Utility program menu and select Exit and then Save  
Settings.  
Selecting a startup device  
If your computer does not start up (boot) from a device such as the CD-ROM,  
diskette, or hard disk as expected, use one of the following procedures to select a  
startup device.  
78 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Selecting a temporary startup device  
Use this procedure to startup from any boot device.  
Note: Not all CDs, hard disks, and diskettes are startable (bootable).  
1. Turn off your computer.  
2. Press and hold the F12 key then turn on your computer. When the Startup  
Device Menu displays, release the F12 key.  
3. Select the desired startup device from the Startup Devices Menu and press  
Enter to begin.  
Note: Selecting a startup device from the Startup Devices Menu does not  
permanently change the startup sequence.  
Changing the startup sequence  
To view or change the primary or automatic power-on startup sequence, do the  
following:  
1. Start the IBM Setup Utility program (see “Starting the IBM Setup Utility  
2. Select Startup.  
3. Select Startup Sequence. See the information displayed on the right side of the  
screen.  
4. Select the sequence of devices for the Primary Startup Sequence, the Automatic  
Startup Sequence, and the Error Startup Sequence.  
5. Select Exit from the IBM Setup Utility menu and then Save Settings.  
If you have changed these settings and want to return to the default settings, select  
Load Default Settings on the Exit menu.  
Advanced settings  
On some computer models, the Advanced settings menu includes a setting to  
Enable/Disable HyperThreading. This feature works only with  
HyperThreading-aware operating systems such as Microsoft Windows XP. The  
default setting for HyperThreading is Enabled. However, if you select Set Defaults  
(HyperThreading is Enabled) and are using an operating system other than  
Windows XP, your computer performance might be degraded. Therefore, you  
should always set HyperThreading to disabled unless you are sure your operating  
system supports hyperthreading.  
Chapter 4. Using the IBM Setup Utility program 79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
80 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix A. Updating system programs  
This appendix contains information about updating system programs and how to  
recover from a POST/BIOS update failure.  
System programs  
System programs are the basic layer of software that is built into your computer.  
They include the power-on self-test (POST), the basic input/output system (BIOS)  
code, and the IBM Setup Utility program. POST is a set of tests and procedures  
that is performed each time you turn on your computer. BIOS is a layer of  
software that translates instructions from other layers of software into electrical  
signals that the computer hardware can understand. You can use the IBM Setup  
Utility program to view and change the configuration and setup of your computer.  
Your computer system board has a module called electrically erasable programmable  
read-only memory (EEPROM, also referred to as flash memory). You can easily update  
POST, BIOS, and the IBM Setup Utility program by starting your computer using a  
flash update diskette or by running a special update program from your operating  
system.  
IBM might make changes and enhancements to the system programs. When  
updates are released, they are available as downloadable files on the World Wide  
Web (see the Quick Reference). Instructions for using the system program updates  
are available in a .txt file that is included with the update files. For most models,  
you can download either an update program to create a system-program-update  
(flash) diskette or an update program that can be run from the operating system.  
Updating (flashing) BIOS from a diskette  
1. Insert a system program update (flash) diskette into the diskette drive (drive A)  
in your computer. System program updates are available at  
http://www.ibm.com/pc/support/ on the World Wide Web.  
2. Turn on the computer. If it is on already, you must turn it off and back on  
again. The update begins.  
Updating (flashing) BIOS from your operating system  
Note: Due to constant improvements being made to the IBM Web site, Web page  
content (including the links referenced in the following procedure) is subject  
to change.  
1. From your browser, type http://www.pc.ibm.com/support in the address field  
and press Enter.  
2. Locate the Downloadable files for your machine type.  
3. Under Select your product, choose your machine type and click Go.  
4. In Downloadable file by category, click BIOS.  
5. Under Download files - BIOS by date, click your machine type.  
6. Scroll down and look for a .txt file that has instructions for Flash BIOS update  
from the operating system. Click the .txt file.  
7. Print these instructions. This is very important since they are not on the screen  
after the download begins.  
© Copyright IBM Corp. 2004  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
8. From your browser, Click Back to return to the list of files. Carefully follow the  
printed instructions to download, extract, and install the update.  
Recovering from a POST/BIOS update failure  
If power to your computer is interrupted while POST/BIOS is being updated (flash  
update), your computer might not restart correctly. If this happens, perform the  
following procedure (also known as a Boot-block Recovery):  
1. Turn off the computer and any attached devices, such as printers, monitors,  
and external drives.  
2. Unplug all power cords from electrical outlets, and remove the cover. See  
Removing the cover in the chapter for your model.  
3. Locate the Clear CMOS/Recovery jumper on the system board. See  
Identifying parts on the system board in the chapter for your model type.  
4. If necessary, refer to Installing adapters to remove any adapters that impede  
access to the Clear CMOS/Recovery jumper.  
5. Move the jumper from the standard position (pins 1 and 2) to pins 2 and 3.  
6. Replace the cover. See Replacing the cover and connecting the cables in the  
chapter for your model type.  
7. Reconnect the power cords for the computer and monitor to electrical outlets.  
8. Insert the POST/BIOS update (flash) diskette into drive A, and turn on the  
computer and the monitor.  
9. After the update session is completed, there will be no video and the series of  
beeps will end. Remove the diskette from the diskette drive, and turn off the  
computer and monitor.  
10. Unplug the power cords from electrical outlets.  
11. Remove the cover. See Removing the cover in the chapter for your model  
type.  
12. Remove any adapters that impede access to the BIOS Configuration jumper.  
13. Replace the Clear CMOS/Recovery jumper to its original position.  
14. Replace any adapters that were removed.  
15. Replace the cover and reconnect any cables that were disconnected.  
16. Turn on the computer to restart the operating system.  
82 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix B. Cleaning the mouse  
This appendix provides instructions on how to clean your mouse. The procedure  
will be different depending on which type of mouse you have.  
Cleaning an optical mouse  
If you experience some problems with your optical mouse, check the following:  
1. Turn the mouse over and look carefully at the lens area.  
a. If there is a smudge on the lens, gently clean the area with a plain cotton  
swab or plain q-tip.  
b. If there is some debris in the lens, gently blow the debris away from the  
area.  
2. Check the surface you are using the mouse on. If you have a very intricate  
picture or pattern beneath the mouse it is difficult for the digital signal  
processor (DSP) to determine changes in the mouse position.  
Cleaning a mouse with a ball  
If the pointer on the screen does not move smoothly with the mouse, you might  
need to clean the mouse.  
Note: The following illustration might be slightly different from your mouse.  
ꢀ1ꢁ Retainer ring  
ꢀ2ꢁ Ball  
ꢀ3ꢁ Plastic rollers  
ꢀ4ꢁ Ball cage  
To clean a mouse with a ball:  
1. Turn off your computer.  
2. Turn the mouse over, with the top side down, and look carefully at the bottom.  
Twist the retainer ringꢀ1ꢁto the unlocked position to remove the ball.  
© Copyright IBM Corp. 2004  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3. Place your hand over the retainer ring and ballꢀ2ꢁ, and then turn the mouse  
over, top side up, so that the retainer ring and ball fall out into your hand.  
4. Wash the ball in warm, soapy water then dry it with a clean cloth. Blow air  
carefully into the ball cageꢀ4ꢁto dislodge dust and lint.  
5. Look for a build up of dirt on the plastic rollersꢀ3ꢁinside the ball cage. This  
build up usually appears as a stripe running across the middle of the rollers.  
6. If the rollers are dirty, clean them by using a cotton swab soaked in isopropyl  
(rubbing) alcohol. Turn the rollers with your finger and continue swabbing  
them until all the dirt is removed. Be sure the rollers are still centered in their  
channels after you clean them.  
7. Remove any fibers from the swab that might be remaining on the rollers.  
8. Replace the ball and the retainer ring.  
9. Turn your computer back on.  
84 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix C. Manual modem commands  
The following section lists commands for manually programming your modem.  
Commands are accepted by the modem while it is in Command Mode. Your  
modem is automatically in Command Mode until you dial a number and establish  
a connection. Commands may be sent to your modem from a PC running  
communication software or any other terminal devices.  
All commands sent to the modem must begin with AT and end with ENTER. All  
commands may be typed in either upper or lower case, but not mixed. To make  
the command line more readable, spaces may be inserted between commands. If  
you omit a parameter from a command that requires one, it is just like specifying a  
parameter of 0.  
Example:  
ATH [ENTER]  
Basic AT commands  
In the following listings, all default settings are printed in bold text.  
Command  
Function  
A
Manually answer incoming call.  
A/  
Repeat last command executed. Do not  
precede A/ with AT or follow with ENTER.  
D_  
0 - 9, A-D, # and *  
last number redial  
pulse dialing  
L
P
Note: Pulse dialing is not supported for  
Australia, New Zealand, Norway, and South  
Africa.  
T
W
,
touch-tone dialing  
wait for second dial tone  
pause  
@
!
wait for five seconds of silence  
flash  
;
return to Command Mode after dialing  
DS=n  
E_  
Dial one of the four telephone numbers  
(n=0-3) stored in the modem non-volatile  
memory.  
E0  
Commands are not echoed  
E1  
Commands are echoed  
+++  
Escape Characters - Switch from Data Mode  
to Command Mode (T.I.E.S. Command)  
H_  
H0  
Force modem on-hook (hang up)  
© Copyright IBM Corp. 2004  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Command  
I_  
Function  
H1  
Force modem off-hook (make busy)  
Note: H1 command is not supported for Italy  
Display product-identification code  
Factory ROM checksum test  
Internal memory test  
I0  
I1  
I2  
I3  
Firmware ID  
I4  
Reserved ID  
L_  
L0  
L1  
L2  
L3  
M0  
M1  
M2  
M3  
Low speaker volume  
Low speaker volume  
Medium speaker volume  
High speaker volume  
M_  
Internal speaker off  
Internal speaker on until carrier detected  
Internal speaker always on  
Internal speaker on until carrier detected and  
off while dialing  
N_  
O_  
Included for compatibility only, provides no  
effect  
O0  
O1  
Return to Data Mode  
Return to Data Mode and initiate an equalizer  
retrain  
P
Set Pulse dial as default  
Modem sends responses  
Read and display value in register r.  
Set register r to value n (n = 0-255).  
Set Tone Dial as default  
Numeric responses  
Q_  
Sr?  
Sr=n  
T
Q0  
V_  
V0  
V1  
W0  
W1  
Word responses  
W_  
X_  
Report DTE speed only  
Report line speed, error correction protocol,  
and DTE speed.  
W2  
X0  
Report DCE speed only  
Hayes Smartmodem 300 compatible  
responses/blind dialing.  
X1  
Same as X0 plus all CONNECT  
responses/blind dialing  
X2  
X3  
X4  
Same as X1 plus dial tone detection  
Same as X1 plus busy detection/blind dialing  
All responses and dial tone and busy signal  
detection  
Z_  
Z0  
Z1  
Reset and retrieve active profile 0  
Reset and retrieve active profile 1  
86 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Extended AT commands  
Command  
&C_  
Function  
&C0  
&C1  
&D0  
&D1  
Force Carrier Detect Signal High (ON)  
Turn on CD when remote carrier is present  
Modem ignores the DTR signal  
&D_  
Modem returns to Command Mode after DTR  
toggle  
&D2  
Modem hangs up, returns to the Command  
Mode after DTR toggle  
&D3  
&F  
Resets modem after DTR toggle  
Recall factory default configuration  
Guard tone disabled  
&F_  
&G_  
&G0  
&G1  
&G2  
&K0  
&K3  
&K4  
&K5  
&K6  
Guard tone disabled  
1800 Hz guard tone  
&K_  
Disable flow control  
Enable RTS/CTS hardware flow control  
Enable XON/XOFF software flow control  
Enable transparent XON/XOFF flow control  
Enable both RTS/CTS and XON/XOFF flow  
control  
&M_  
&P_  
&M0  
&P0  
&P1  
&P2  
Asynchronous operation  
US setting for off-hook-to-on-hook ratio  
UK and Hong Kong off-hook-to-on-hook ratio  
Same as &P0 setting but at 20 pulses per  
minute  
&P3  
Same as &P1 setting but at 20 pulses per  
minute  
&R_  
&S_  
&R0  
&R1  
&S0  
&S1  
Reserved  
CTS operates per flow control requirements  
Force DSR Signal High (ON)  
DSR off in command mode, on in on-line  
mode  
&T_  
&T0  
&T1  
&T3  
&T4  
Ends test in progress  
Perform Local Analog Loopback Test  
Perform Local Digital Loopback Test  
Grant Remote Digital Loopback Test request  
by remote modem  
&T5  
&T6  
&T7  
Deny Remote Digital Loopback Test request  
Perform a Remote Digital Loopback Test  
Perform a Remote Digital Loopback Test and  
Self-Test  
&T8  
&V0  
Perform Local Analog Loopback Test and  
Self-Test  
&V  
Displays Active and Stored Profiles  
Appendix C. Manual modem commands 87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Command  
&W_  
Function  
&V1  
&W0  
&W1  
%E0  
%E1  
Display Last Connection Statistics  
Stores the active profile as Profile 0  
Stores the active profile as Profile 1  
Disable auto-retrain  
%E_  
Enable auto-retrain  
+MS?  
Displays the current Select Modulation  
settings  
+MS=?  
Displays a list of supported Select Modulation  
options  
+MS=a,b,c,e,f  
Select modulation where: a=0, 1, 2, 3, 9, 10, 11,  
12, 56, 64, 69; b=0-1; c=300-56000; d=300-  
56000; e=0-1; and f=0-1. A, b, c, d, e, f  
default=12, 1, 300, 56000, 0, 0. Parameter a″  
specifies the modulation protocol desired  
where: 0=V.21, 1=V.22, 2=V.22bis, 3=V.23,  
9=V.32, 10=V.32bis, 11=V.34,  
12=V.90,K56Flex,V.34......,56=K 56Flex,  
V.90,V.34......, 64=Bell 103, and 69=Bell 212.  
Parameter bspecifies automode operations  
where: 0=automode disabled, 1= automode  
enabled with V.8/V.32 Annex A. Parameter c″  
specifies the minimum connection data rate  
(300- 56000). Parameter dspecifies the  
maximum connection rate (300-56000);  
Parameter especifies the codec type (0=  
Law, and 1=A-Law). Parameter fspecifies  
robbed bitsignaling detection (0=detection  
disabled 1=detection enabled)  
MNP/V.42/V.42bis/V.44 commands  
Command  
Function  
%C_  
%C0  
%C1  
%C2  
%C3  
&Q0  
&Q5  
&Q6  
Disable MNP Class 5 and V.42bis data compression  
Enable MNP Class 5 data compression only  
Enable V.42bis data compression only  
Enable MNP Class 5 and V.42bis data compression  
Direct data link only (same as \N1)  
V.42 data link with fallback options  
Normal data link only (same as \N0)  
Disable V.44  
&Q_  
+DS44=0, 0  
+DS44=3, 0  
+DS44?  
Enable V.44  
Current values  
+DS44=?  
List of support values  
88 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Fax Class 1 commands  
+FAE=n  
Data/Fax Auto Answer  
Service Class  
+FCLASS=n  
+FRH=n  
+FRM=n  
+FRS=n  
Receive data with HDLC framing  
Receive data  
Receive silence  
+FTH=n  
+FTM=n  
+FTS=n  
Transmit data with HDLC framing  
Transmit data  
Stop transmission and wait  
Fax Class 2 commands  
+FCLASS=n  
+FAA=n  
+FAXERR  
+FBOR  
+FBUF?  
+FCFR  
Services class.  
Adaptive answer.  
Fax error value.  
Phase C data bit order.  
Buffer size (read only).  
Indicate confirmation to receive.  
Service class.  
+FCLASS=  
+FCON  
+FCIG  
Facsimile connection response.  
Set the polled station identification.  
Report the polled station identification.  
Capability to receive.  
+FCIG:  
+FCR  
+FCR=  
Capability to receive.  
+FCSI:  
Report the called station ID.  
DCE capabilities parameters.  
Report current session.  
Current session results.  
Report remote capabilities.  
Current sessions parameters.  
Begin or continue phase C receive data.  
Data transmission.  
+FDCC=  
+FDCS:  
+FDCS=  
+FDIS:  
+FDIS=  
+FDR  
+FDT=  
+FDTC:  
+FET:  
Report the polled station capabilities.  
Post page message response.  
Transmit page punctuation.  
Call termination with status.  
Session termination.  
+FET=N  
+FHNG  
+FK  
+FLID=  
+FLPL  
Local ID string.  
Document for polling.  
+FMDL?  
+FMFR?  
Identify model.  
Identify manufacturer.  
Appendix C. Manual modem commands 89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
+FPHCTO  
+FPOLL  
+FPTS:  
Phase C time out.  
Indicates polling request.  
Page transfer status.  
Page transfer status.  
Identify revision.  
+FPTS=  
+FREV?  
+FSPT  
Enable polling.  
+FTSI:  
Report the transmit station ID.  
Voice commands  
#BDR  
#CID  
Select Baud Rate  
Enable Caller ID detection and reporting format  
Select Data, Fax or Voice/Audio  
Identify Model  
#CLS  
#MDL?  
#MFR?  
#REV?  
#TL  
Identify Manufacturer  
Identify Revision Level  
Audio output transmit level  
Query Buffer Size  
#VBQ?  
#VBS  
#VBT  
#VCI?  
#VLS  
#VRA  
#VRN  
#VRX  
#VSDB  
#VSK  
#VSP  
#VSR  
#VSS  
#VTD  
#VTM  
#VTS  
#VTX  
Bits per sample (ADPCM or PCM)  
Beep Tone Timer  
Identify Compression Method  
Voice line select  
Ringback goes away timer  
Ringback never came timer  
Voice Receive Mode  
Silence deletion tuner  
Buffer skid setting  
Silence detection period  
Sampling rate selection  
Silence deletion tuner  
DTMF tone reporting capability  
Enable timing mark placement  
Generate tone signals  
Voice transmit mode  
90 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Attention Switzerland User:  
If your Swisscom phone line does not have Taxsignal switched OFF, modem  
function may be impaired. The impairment may be resolved by a filter with  
the following specifications:  
Telekom PTT SCR-BE  
Taximpulssperrfilter-12kHz  
PTT Art. 444.112.7  
Bakom 93.0291.Z.N  
Appendix C. Manual modem commands 91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
92 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix D. Customer replaceable unit (CRU) parts list  
For your computer, the following parts are designated customer replaceable unit  
(CRU) parts. Refer to the warranty section of your Quick Reference for more  
information.  
CRU parts list  
Air duct with/without fan  
All bezels  
All cables  
All external speakers  
All hard disk drives, optical drives, and diskette drives  
All keyboards  
All keylocks  
All memory  
All mice  
All option and adapter cards  
Battery, 3.0V CMOS battery  
Control panel assembly  
EMC shield 5.25″  
Fan assembly, 80 mm, fixed speed  
Fan bracket assembly  
Hard disk drive bracket assembly  
Hard disk drive mounting bracket assembly  
Hard disk drive tray  
Input/output cam bracket  
Internal speaker assembly  
Pivot lock, 3.5 diskette drive  
Pivot lock, 5.25 DASD  
Retainer, cards input/output  
RFID antenna  
Speaker power supply  
System board shield kit  
© Copyright IBM Corp. 2004  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
94 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix E. Notices  
IBM may not offer the products, services, or features discussed in this document in  
all countries. Consult your local IBM representative for information on the  
products and services currently available in your area. Any reference to an IBM  
product, program, or service is not intended to state or imply that only that IBM  
product, program, or service may be used. Any functionally equivalent product,  
program, or service that does not infringe any IBM intellectual property right may  
be used instead. However, it is the user’s responsibility to evaluate and verify the  
operation of any non-IBM product, program, or service.  
IBM may have patents or pending patent applications covering subject matter  
described in this document. The furnishing of this document does not give you  
any license to these patents. You can send license inquiries, in writing, to:  
IBM Director of Licensing  
IBM Corporation  
North Castle Drive  
Armonk, NY 10504-1785  
U.S.A.  
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS  
PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER  
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS  
FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of  
express or implied warranties in certain transactions, therefore, this statement may  
not apply to you.  
This information could include technical inaccuracies or typographical errors.  
Changes are periodically made to the information herein; these changes will be  
incorporated in new editions of the publication. IBM may make improvements  
and/or changes in the product(s) and/or the program(s) described in this  
publication at any time without notice.  
The products described in this document are not intended for use in implantation  
or other life support applications where malfunction may result in injury or death  
to persons. The information contained in this document does not affect or change  
IBM product specifications or warranties. Nothing in this document shall operate  
as an express or implied license or indemnity under the intellectual property rights  
of IBM or third parties. All information contained in this document was obtained  
in specific environments and is presented as an illustration. The result obtained in  
other operating environments may vary.  
IBM may use or distribute any of the information you supply in any way it  
believes appropriate without incurring any obligation to you.  
Any references in this publication to non-IBM Web sites are provided for  
convenience only and do not in any manner serve as an endorsement of those Web  
sites. The materials at those Web sites are not part of the materials for this IBM  
product, and use of those Web sites is at your own risk.  
© Copyright IBM Corp. 2004  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Television output notice  
The following notice applies to models that have the factory-installed  
television-output feature.  
This product incorporates copyright protection technology that is protected by  
method claims of certain U.S. patents and other intellectual property rights owned  
by Macrovision Corporation and other rights owners. Use of this copyright  
protection technology must be authorized by Macrovision Corporation, and is  
intended for home and other limited viewing uses only unless otherwise  
authorized by Macrovision Corporation. Reverse engineering or disassembly is  
prohibited.  
Trademarks  
The following terms are trademarks of International Business Machines  
Corporation in the United States, other countries, or both:  
IBM  
ThinkCentre  
Wake on LAN  
PS/2  
Microsoft and Windows are trademarks of Microsoft Corporation in the United  
States, other countries, or both.  
Intel, Celeron, and Pentium are trademarks of Intel Corporation in the United  
States, other countries, or both.  
Other company, product, or service names may be trademarks or service marks of  
others.  
96 User Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Index  
drives (continued)  
A
adapters  
installing  
E
I
input/output (I/O)  
installing options  
Types 8084, 8085, 8147, 8148, and 8179  
B
Types 8126, 8174, 8175, and 8176  
C
changing the battery  
commands  
Types 8149, 8177, and 8178  
connector description  
K
cover  
removing  
L
replacing  
locating components  
M
memory  
D
drives  
modem  
© Copyright IBM Corp. 2004  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Download from Www.Somanuals.com. All Manuals Search And Download.  
ꢀꢁꢂꢃ  
Part Number: 19R0764  
Printed in USA  
(1P) P/N: 19R0764  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Lawn Mower GS1548 User Manual
Lexmark All in One Printer 340n User Manual
LG Electronics DVD Player BP730 User Manual
LG Electronics Projector RD JT91 User Manual
Makita Drill BDF460SH User Manual
Mattel Motorized Toy Car M8487 0920 User Manual
Maytag Washer MAV 3 User Manual
Metra Electronics Automobile Accessories 88 00 3302 User Manual
Metz Camcorder 28 AF 4 N User Manual
Middleby Marshall Oven PS540 User Manual