PRODUCT LITERATURE
W1996 Lennox Industries Inc.
Dallas, Texas
503,517M
9/98
G23
SERIES
Supersedes 8/96
GAS FURNACE
Litho U.S.A.
WARNING
If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or loss of
life.
WHAT TO DO IF YOU SMELL GAS:
D Do not try to light any appliance.
Do not store or use gasoline or other flamĆ
mable vapors and liquids in the vicinity of
this or any other appliance.
D Extinguish any open flames.
D Do not touch any electrical switch; do not use any
phone in your building.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
D Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
D If you cannot reach your gas supplier, call the fire deĆ
partment.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Before attempting to perform any service or mainteĆ
nance, turn the electrical power to unit OFF at disĆ
connect switch.
WARNING
Carbon monoxide gas is invisible, odorless, and
toxic.
Exposure to this gas can cause personal injury and even
death to all occupants, including pets. Any item that is powĆ
ered by or gives off heat from a combustion process (inĆ
cluding lawn mowers, automobiles, and fireplaces) has the
potential to produce carbon monoxide gas. Because of
this, Lennox recommends the use of a carbon monoxĆ
ide detector in your home, even if you do not own gas
appliances. Reliable detectors are available at reasonĆ
able retail prices. Contact your independent Lennox dealer
for more details about this investment in your safety.
WARNING
Do not use this furnace if any part has been under
water. Immediately call a qualified service techniĆ
cian to inspect the furnace and to replace any part
of the control system and any gas control which
has been under water.
Your furnace is designed to meet standards set by nationĆ
al agencies, and to operate safely when properly installed
and maintained. However, the unit's performance can be
greatly impacted by the individual installation and the opĆ
erating environment. It is your responsibility to ensure
that this appliance is maintained. Proper maintenance is
critical for your safety and the satisfactory operation of the
product. Lennox strongly recommends annual inĆ
spection and maintenance of this appliance. Contact
your independent Lennox dealer for an inspection by a
qualified service technician.
IMPORTANT
Any additions, changes, or conversions required in
order for the appliance to satisfactorily meet the apĆ
plication needs must be made by a Lennox service
technician using factory specified and approved
parts.
Important Directions
1- Keep the furnace area clear and free of combustible
material, gasoline, and other flammable vapors and
liquids. If installed in an insulated area, furnace must
be kept free of insulating material. Insulating material
may be combustible.
Lighting Information & Operation
2- DO NOT obstruct air flow to unit. Unit must receive an
unobstructed flow of combustion and ventilating air.
3- DO NOT store chlorine or fluorine products near unit
or introduce these products into the combustion air.
These products can cause furnace corrosion.
WARNING
If you do not follow these instructions exactly, a fire
or explosion may result causing property damage,
personal injury or loss of life.
4- DO NOT draw return air from a room where this
furnace, or any other gas appliance (ie., a water
heater), is installed. When return air is drawn from a
room, a negative pressure is created in the room. If a
gas appliance is operating in a room with negative
pressure, the flue products can be pulled back down
the vent pipe and into the room. This reverse flow of
the flue gas may result in incomplete combustion and
the formation of carbon monoxide gas. This toxic gas
might then be distributed throughout the house by
the furnace duct system.
BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or turn
by hand, do not try to repair it, call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
Your furnace is a gas appliance. It is critical that the gas
supplied to the unit be completely burned to avoid the proĆ
duction of carbon monoxide gas. Complete combustion
of the gas requires, but is not limited to, correct gas presĆ
sure and gas flow rate, adequate combustion, air, and
proper venting.
To place G23 furnace into operation:
G23(X) units are equipped with a SureLight ignition
system. Do not attempt to manually light burners on
these furnaces. Each time thermostat calls for heat,
the burners will be automatically lit. The ignitor does
not get hot when there is no call for heat on units with
SureLight ignition system.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Valve Operation (Figure 3)
NOTE-When unit is first started, steps 1 through 11 may
need to be repeated to purge air from line.
1- STOP! Read the safety information at the beginning
of this section.
12- If the appliance still will not operate, follow the inĆ
structions To Turn Off Gas To Unit" and call your serĆ
vice technician or gas supplier.
2- Set thermostat to lowest setting. See figure 2.
THERMOSTATS
Turning Off The Gas To The Unit
1- Set thermostat to lowest setting.
2- Turn off all electrical power to unit if service is to be
performed.
3- Remove upper access panel.
4- On Honeywell VR8204 gas valves, turn knob on gas
valve clockwise to OFF. For White Rodgers 36E
gas valves, move switch to OFF. Do not force.
FIGURE 2
5- Replace upper access panel.
3- Turn off all electrical power to appliance.
4- This appliance is equipped with an ignition device
which automatically lights the burners. Do not try to
light the burners by hand.
Filters
A filter must be in place anytime the unit is in operation. The
filter may be located in the unit (optional kit) or installed in a
return air grille. Ask your dealer to show you the filter location.
The filter should be inspected monthly and cleaned when
necessary to assure proper furnace operation.
5- Remove upper access panel.
6- On Honeywell VR8204 gas valves, turn knob on gas
valve clockwise
to OFF. For White Rodgers 36E
gas valves, move switch to OFF. Do not force the
Filters used inside the G23 series unit are available from LenĆ
nox and must be ordered separately. These foam filters may
be cleaned for reuse. If replacement is necessary, order LenĆ
nox part no. 31J81 for 14 X 25 inch filter for G23Q2-50,
Q3-50 and Q2/3-75 units, P-8-7822 for 16 X 25 inch filter for
G23Q3-100 units, and P-8-7831 for 20 X 25 inch filter for
G23Q3/4-100, Q3/4-125, Q4/5-75, Q4/5-100, Q5/6-125 and
Q5/6-150 units. Use the following procedure to clean filter.
Refer to figure 1.
switch. See figure 3.
HONEYWELL VR8204 SERIES GAS VALVE
ON
In-Unit Filter with Bottom Return Air
1- Turn off electric power to furnace.
OFF
GAS VALVE SHOWN IN OFF POSITION
2- Remove blower access panel.
3- Remove filter by pressing side filter clips and pulling filter
up and out. See figure 4.
WHITE RODGERS
36E GAS VALVE
BOTTOM RETURN FILTER INSTALLATION
REAR FILTER CLIP
GAS VALVE
SHOWN
IN OFF
FURNACE
BACK
SIDE FILTER CLIPS (2)
POSITION
FIGURE 3
RETURN AIR OPENING
7- Wait fifteen (15) minutes to clear out any gas. If you
then smell gas, STOP! Immediately call your gas
supplier from a neighbor's phone. Follow the gas
supplier's instructions. If you do not smell gas go to
next step.
FURNACE
FURNACE
FRONT
BASE BOTĆ
TOM
FIGURE 4
8- For Honeywell VR8204 gas valves, turn knob on gas
4- Clean filter with cold water and a mild soap. Direct
water through filter in the opposite direction of air
flow. Remove all soap residue.
valve counterclockwise
to ON. For White RodgĆ
ers 36E gas valves, move switch to ON. Do not force.
9- Replace upper access panel.
5- Allow filter to dry then spray with filter handicoater
(P-8-5069), available from your Lennox dealer, prior
to reinstallation.
10- Turn on all electrical power to unit.
11- Set thermostat to desired setting.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
6- Place filter in bottom of blower compartment beneath
rear filter clip. Press down on filter sides. Filter clips
flex allowing filter to snap into place.
Seasonal Inspections
A qualified service technician should inspect the comĆ
plete system each season (heating and cooling). The folĆ
lowing maintenance procedures should be conducted by
a qualified service technician. Do not attempt to service
the unit in any way.
7- Replace blower access panel.
WARNING
Venting System
Blower door must be securely in place when blower
and burners are operating. Gas fumes, which could
contain carbon monoxide, can be drawn into living
space which could cause personal injury or death.
Annually (before heating season) inspect furnace venting
system, draft hood, vent cap, heat exchanger, and burners
for corrosion, deterioration, or deposits of debris. Remove
any obstructions.
In-Unit Filter with Side Return Air (See Figure 5)
1- Turn off electric power to furnace.
Inspect furnace venting system to make sure it is in
place, physically sound, and without holes, corrosion, or
blockage. Vent connector must be in correct position,
sloped upward and be physically sound without holes or
excessive corrosion.
2- Locate the filter door of the filter rack assembly.
3- Using the filter door pins, pull filter door, with filter atĆ
tached, out of filter rack assembly. Remove filter door
from filter by pulling up on securing tabs.
4- Clean filter with cold water and a mild soap. Direct waĆ
ter through filter in the opposite direction of air flow. AlĆ
low filter to dry then spray with filter handicoater, availĆ
able from your Lennox dealer, prior to reinstallation.
Inspect furnace return air duct connection to ensure duct is
sealed to the furnace and terminates outside the space conĆ
taining the furnace.
Inspect the physical support of the furnace to guarantee that
it is sound without sagging, cracks or gaps around base and
it maintains seal between base and support.
5- Position filter door on end of filter so that the thumb
tab side of the filter door is away from the furnace.
Check for correct air flow position. Squeeze thumb
tabs to secure filter to door.
During a seasonal check the service technician will inspect
the indoor blower and the burner flames along with the ventĆ
ing system.
6- Guide filter and filter door into the filter rack
installed on side of furnace. Push door into filter
rack until secure.
Blower
REMOVING / REPLACING FILTER DOOR
Check and clean blower wheel for any debris. Blower motor
is pre-lubricated for extended bearing life. No further lubricaĆ
tion is needed.
FILTER DOOR
PIN
TAB
Burner Flame
Burner Flame
Start burner and allow to operate for a few minutes to esĆ
tablish normal burning conditions. Check burner flame by
observation. Flame should be predominantly blue and
strong in appearance.
FILTER
FILTER DOOR
FILTER DOOR
PIN
CAUTION
To ensure proper operation, a qualified technician
should periodically check the burner flame.
TAB
FIGURE 5
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Your vigilance may pay off in early detection of a problem
before either personal injury or property damage occurs.
Do not hesitate to contact a qualified service technician as
an investment in your well being.
Service Reminder
Call your Lennox service technician if unit is inoperative.
Before calling, always check the following to be sure serĆ
vice is required.
Planned Service
1- Check that electrical disconnect switches are ON.
2- Check room thermostat for proper setting.
3- Replace any blown fuses or reset circuit breakers.
4- Gas valve should be ON.
You should expect a service technician to check the folĆ
lowing items during an annual inspection. Power to the
unit must be shut off for the service technician's safety.
Fresh air grilles and louvers (on the unit and in the room
where the furnace is installed) - Must be open and unobĆ
structed to provide combustion air.
5- Air filter should not be plugged limiting air flow.
6- Is gas turned on at meter?
7- Is manual main shut-off valve open?
Burners- Must be inspected for rust, dirt, or signs of water.
Vent pipe - Must be inspected for signs of water, damĆ
aged or sagging pipe, or disconnected joints.
Unit appearance - Must be inspected for rust, dirt, signs
of water, burnt or damaged wires, or components.
Blower access door - Must be properly in place and proĆ
vide a seal between the return air and the room where the
furnace is installed.
Safety Precautions
If you discover any of the following, shut down your
unit, and contact an independent Lennox dealer for
an inspection by a qualified technician.
D If you repeatedly hear any new or unfamiliar sounds
while your unit is operating, there may be a problem.
For example, poorly performing burners can produce
unfamiliar noises.
Return air duct - Must be properly attached and provide
an air seal to unit.
D If you smell any unusual odors, your unit may be operĆ
ating improperly. For example, units can give off unfaĆ
miliar odors if components are required to operate in
abnormal conditions.
Operating performance - Unit must be observed during
operation to monitor proper performance of the unit and
the vent system.
Combustion gases - Flue products must be analyzed
and compared to the unit specifications.
D Look for visible signs of a malfunctioning unit. ExamĆ
ples include unusual amounts of condensate on winĆ
dows inside your house, visibly burnt components or
unusual dirt or rust accumulations on the vent pipe or
in the unit.
Problems detected during the inspection may make it
necessary to temporarily shut down the furnace until the
items can be repaired or replaced.
D If you experience headache, nausea, fatigue, or dizziĆ
ness, the cause could be exposure to carbon monoxĆ
ide gas. This is often misdiagnosed as the flu because
symptoms are similar. If you suffer from flu-like sympĆ
toms that are exaggerated at home, but seem to subĆ
side while you are away from the house, exposure to
carbon monoxide could be the cause.
Pay attention to your furnace. Situations can arise beĆ
tween annual furnace inspections that may result in unĆ
safe operation. For instance, items innocently stored next
to the furnace may obstruct the combustion air supply.
This could cause incomplete combustion and the producĆ
tion of carbon monoxide gas.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|