INSTALLATION INSTRUCTIONS
EDV Direct-Vent
Gas Fireplaces
™
MODELS
P/N 850018M Rev. H 01/2011
This manual is one of a set of two supporting this product.
Refer to P/N 875022M for Care and Operation Instructions.
MILLIVOLT:
ELECTRONIC:
EDVSTNM-B
EDVSTPM-B
EDVPFNM-B
EDVPFPM-B
EDVCRNM-B
EDVCRPM-B
EDVCLNM-B
EDVCLPM-B
EDVSTNE-B
EDVPFNE-B
EDVCRNE-B
EDVCLNE-B
Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 850018CF.
Portland
US
OTL Report No. 116-F-04-5
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
INSTALLATEUR : Laissez cette notice avec l'appareil.
CONSOMMATEUR : Conservez cette notice pour
consultation ultérieure.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating
plate. This appliance is not convertible for use with other gases unless a certified kit is used.
/
/
WARNING AVERTISSEMENT AVISO
• HOT GLASS WILL CAUSE
BURNS.
• UNE SURFACE VITRÉE CHAUDE
PEUT CAUSER DES BRÛLURES.
• LAISSER REFROIDIR LA SURFACE
VITRÉE AVANT D'Y TOUCHER.
• EL VIDRIO CALIENTE
CAUSARÁ QUEMADURAS.
• USTED DEBE NUNCA
• DO NOT TOUCH GLASS
UNTIL COOLED.
TOCAR EL VIDRIO CALIENTE.
• NEVER ALLOW CHILDREN
TO TOUCH GLASS.
• NE PERMETTEZ JAMAIS À UN ENFANT • LOS NIÑOS DEBEN NUNCA
DE TOUCHER LA SURFACE VITRÉE.
TOCAR EL VIDRIO.
WARNING: If the information in these instructions
is not followed exactly, a fire or explosion may
result, causing property damage, personal injury,
or death.
AVERTISSEMENT : Assurez-vous de bien suivre les
instructions données dans cette notice pour réduire au
minimum le risque d’incindie ou d’explosion ou pour
éviter tout dommage matériel, toute blessure ou la mort.
- Ne pas entreposer ni utilizer d’essence ni d’autres vapeurs
ou liquides inflammables dans le voisinage de cet appareil
ou de tout autre appareil.
-
vapors and liquids in the vicinity of this or any other
appliance.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• Ne pas tenter d’allumer d’appareil.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• Ne touchez à aucan interrupteur. Ne pas vous servir des
téléphones se trouvant dans le bâtiment où vous trouvez.
• Appelez immédiatement votre fournisseur de gaz depuis
un voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
- L’installation et l’entretien doivent être assurés par un
installateur ou un service d’entretien qualifié ou par le
fournisseur de gaz.
•
department.
- Installation and service must be performed by a
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Installation and repair should be done
by a qualified service person. The appliance
should be inspected before use and at least
annually by a professional service person.
More frequent cleaning may be required
due to excessive lint from carpeting, bed-
ding material, etcetera. It is imperative
that control compartments, burners and
circulating air passageways of the appliance
be kept clean.
Misc. Codes / Standards -
TheInstallationmustconformtolocalcodesor,
in the absence of local codes, with the National
Fuel Gas Code, ANSI Z223.1/NFPA 54 - latest
edition(InCanada,thecurrentCAN/CSA-B149.1
installation code).
WARNING
Improper installation, adjust-
ment, alteration, service or
maintenance can cause injury
or property damage. Refer to
this manual. For assistance or
additional information consult
a qualified installer, service
agency or the gas supplier.
The appliance, when installed, must be electri-
cally grounded and wired in accordance with
local codes or, in the absence of local codes,
with the National Electrical Code, ANSI/NFPA
70 - latest edition, or the Canadian Electrical
Code, CSA C22.1 - latest edition.
Remarque: L’installation et la réparation
devrait être confiées à un technicien qualifié.
L’appareildevraitfairel’objetd’uneinspection
par un technicien professionnel avant d’être
utilisé et au moins une fois l’an par la suite.
Des nettoyages plus fréquents peuvent être
nécessaires si les tapis, la literie, et cetera
produisent une quantité importante de pous-
sière. Il est essentiel que les compartiments
abritant les commandes, les brûleurs et les
conduits de circulation d’air de l’appareil
soient tenus propres.
Provide adequate clearances around air open-
ings and adequate accessibility clearance for
serviceandproperoperation.Neverobstructthe
front or back openings of the appliance.
WARNING
Failure to comply with these
installationinstructionswillresult
in an improperly installed and
operating appliance, voiding its
warranty. Anychangetothisappli-
anceand/oritsoperatingcontrols
is dangerous.
These appliances are designed to operate on
natural or propane gas only. The use of other
fuels or combination of fuels will degrade
the performance of this system and may be
dangerous.
Do not use these appliances if any part
has been under water. Immediately call a
qualified, professional service technician
to inspect the appliance and to replace any
parts of the control system and any gas
control which have been under water.
These fireplaces are designed as supplemental
heaters. Therefore, it is advisable to have an
alternate primary heat source when installed
in a dwelling.
WARNING
Clothing or other flammable
material should not be placed
on or near the appliance.
Nepasutilisercetappareils’ilaétéplongé,
même partiellement, dans l’eau. Ap-
peler un technicien qualifié pour inspecter
l’appareil et remplacer toute partie du
systèmedecommandeettoutecommande
qui a été plongée dans l’eau.
Millivolt Models - The millivolt appliances are
manually controlled and feature a spark igniter
(piezo) that allows the appliance's pilot gas to
be lit without the use of matches or batteries.
This system provides continued service in the
event of a power outage.
AVERTISSEMENT
On ne devrait pas placer de
vêtements ni d’autres matières
inflammables sur l’appareil ni à
proximité.
Millivoltmodelscomestandardwithamanually-
modulated gas valve; flame appearance and
heat output can be controlled at the gas valve.
The BTU Input for these appliances is shown
in Table 1.
WARNING
Improper installation or use of
thisappliancecancauseserious
injury or death from fire, burns,
explosions or carbon monoxide
poisoning.
WARNING
Electronic Models - Electronic models have a
fixed rate gas valve. Input of electronic models
is shown in Table 1.
Any safety screen or guard
removed for servicing the appli-
ance must be replaced prior to
operating the appliance.
Only trim kit(s) supplied by the manufacturer
shall be used in the installation of this ap-
pliance.
Input (BTU) Gas Valves (all models)
All Models
Fuel
Type
Input Rate
(BTU / HR)
Seules les trousses de garniture fournies
par le fabricant doivent être utilisées pour
l’installation de cet appareil.
AVERTISSEMENT
39,000 high
31,000 low
Millivolt
Millivolt
Natural
Propane
Natural
Tout écran ou protecteur retiré
pour permettre l’entretien de
l’appareil doit être remis en
place avant de mettre l’appareil
en marche.
39,000 high
31,000 low
These appliances comply with National Safety
StandardsandaretestedandlistedbyOMNI-Test
Laboratories, Inc. (Report No. 116-F-04-5) to
ANSI Z21.88 (in Canada, CSA-2.33), and CAN/
CGA-2.17-M91 in both USA and Canada, as
vented gas fireplace heaters.
Electronic
39,000
39,000
Electronic
Propane
Both millivolt and electronic versions of
these appliances are listed by OMNI-Test
Laboratories for installation in bedrooms
and Manufactured Homes.
Table 1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Pressure - All Models
Orifice Sizes - Sea Level to High Altitude
(All Models)
ON/OFF Switch
Manifold Pressure Port
Tables 2 and 3 show the appliances' inlet and
manifold gas pressure requirements:
These appliances are tested and approved for
installation at elevations of 0-4500 feet (0-1372
meters)abovesealevelusingthestandardburner
orifice sizes (marked with an "*" in Table 4 ).
Forelevationsabove4500feet,contactyourgas
supplier or qualified service technician.
Inlet
Pressure
Port
Inlet Gas Supply Pressure
(all models)
Fuel #
Minimum
Maximum
4.5" WC
(1.12 kPa)
10.5" WC
(2.61 kPa)
Electronic
Gas Control
Valve
Natural Gas
Deration - At higher elevations, the amount
of BTU fuel value delivered must be reduced
by either:
11.0" WC
(2.74 kPa)
13.0" WC
(3.23 kPa)
Propane
Honeywell Electronic
Gas Valve
• Using gas that has been derated by the gas
company.
Figure 2
Table 2
• By changing the burner orifice to a smaller
size as regulated by the local authorities having
jurisdiction and by the (USA) National Fuel Gas
Code NFPA 54/ANSI Z223.1 - latest edition or,
in Canada, the CAN/CSA-B149.1 codes - latest
edition.
Manifold Gas Supply Pressure
(all models)
REQUIREMENTS FOR THE COMMON-
WEALTH OF MASSACHUSETTS
Fuel #
Low
High
These fireplaces areapproved for installationin
the US state of Massachusetts if the following
additional requirements are met:
• Install this appliance in accordance with
Massachusetts Rules and Regulations 248
C.M.R.
• Installation and repair must be done by a
plumber or gas fitter licensed in the Com-
monwealth of Massachusetts.
• The flexible gas line connector used shall
not exceed 36 inches (92 centimeters) in
length.
• The individual manual shut-off must be a
T-handle type valve.
Natural (Lo) 2.2" WC
(Hi) 3.5" WC
(0.87 kPa)
Gas
(0.55 kPa)
Installtheapplianceaccordingtotheregulations
of the local authorities having jurisdiction and,
in the USA, the National Fuel Gas Code NFPA
54 / ANSI Z223.1 - latest edition or, in Canada,
the CAN/CSA-B149.1 - latest edition.
(Lo) 6.3" WC (Hi) 10.0" WC
(1.57 kPa) (2.49 kPa)
Propane
Table 3
Test gauge connections are provided on the
front of the millivolt and electronic gas control
valve (identified IN for the inlet and OUT for the
manifold side). The control valves have a 3/8"
(10mm) NPT thread inlet and outlet side of the
valve (refer to Figures 1 and 2).
Flame breadth, height and width will diminish
4% for every 1,000 feet of altitude.
Burner Orifice Sizes (all models)
Natural
Propane
Elevation
Gas
Gas
Propane tanks are at pressures that will cause
damage to valve components. Verify that the
tanks have step down regulators to reduce the
pressure to safe levels.
Feet (meters)
Massachusetts Horizontal Vent Requirements
drill size (inches)
drill size (inches)
0-4500
(0-1372)
(0.125")
21L81 •
#41 (0.096")
*
*
IntheCommonwealthofMassachusetts,hori-
zontal terminations installed less than seven
(7) feet above the finished grade must comply
with the following additional requirements:
• A hard wired carbon monoxide detector
with an alarm and battery back-up must be
installed on the floor level where the gas
fireplace is installed. The carbon monoxide
detector must comply with NFPA 720, be
ANSI/UL 2034 listed and be ISA certified.
• A metal or plastic identification plate must
be permanently mounted to the exterior of
thebuildingataminimumheightofeight(8)
feet above grade and be directly in line with
the horizontal termination. The sign must
read, in print size no less than one-half (1/2)
inch in size, GAS VENT DIRECTLY BELOW.
KEEP CLEAR OF ALL OBSTRUCTIONS.
21L82 •
* Standard size installed at factory
• Part /Cat. Number
Table 4
These appliances must be isolated from the
gas supply piping system (by closing their
individual manual shut-off valve) during any
pressure testing of the gas supply piping
system at test pressures equal to or less
than 1/2 psig (3.5 kPa).
Gas Valve Diagrams
See Figure 1 for Millivolt models and Figure 2
For Electronic Models.
Theseappliancesandtheirindividualshut-off
valves must be disconnected from the gas
supply piping system during any pressure
testing of that system at pressures greater
than 1/2 psig (3.5 kPa).
Pilot Adjustment
Screw
Main Gas Control Knob
OFF/PILOT/ON
T
L
I
P
N
O
T
W O
L
O
L I
P
F
O
These appliances must not be connected to a
chimney or flue serving a separate solid fuel
burning appliance.
H
I
IN OUT
NEW YORK CITY, NEW YORK (MEA)
Manifold Pressure Tap
HI/LO Variable
Flame Height
Adjustment
Inlet Pressure Tap
Installation of these fireplaces are approved
for installation in New York City in the US state
of New York.
Figure 1 - SIT Millivolt Gas Valve
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
COLD CLIMATE INSULATION
For cold climate installations, seal all cracks
around your appliance with noncombustible
material and wherever cold air could enter
the room. It is especially important to insulate
outside chase cavity between studs and under
floor on which appliance rests, if floor is above
ground level. Gas line holes and other open-
ings should be caulked or stuffed with unfaced
fiberglass insulation.
HORIZONTAL VENT
- REAR
VERTICAL VENT
If the fireplace is being installed on a cement
slab in cold climates, a sheet of plywood or
otherraisedplatformcanbeplacedunderneath
to prevent cold transfer to the fireplace and into
the room. It also helps to sheetrock inside
surfaces and tape for maximum air tightness
and caulk firestops.
MANUFACTURED HOME
REQUIREMENTS
HORIZONTAL VENT
- TOP
Thisappliancemaybeinstalledinanaftermarket
permanently located, manufactured home and
must be installed in accordance with the manu-
facturer's instructions and the Manufactured
Home Construction and Safety Standard, Title
24 CFR, Part 3280, in the United States, or the
StandardforInstallationinMobileHomes,CAN/
CSA Z240 MH Series, in Canada.
When the unit is installed with one side flush with a wall,
the wall on the other side of the unit must not extend
beyond the front edge of the unit.
(See-Through Model Shown)
Corner - Left
(EDVCL)
Corner - Right
Cetappareilpeutêtreinstallécómmedumatéri-
eld'originedansunemaisonpréfabriquée(É.U.
seulement) ou mobile et doit être installé selon
les instructions du fabricant et conformément
à la norme Manufactured Home Constructions
and Safety, Title 24 CFR, Part 3200 aux Unis ou
à la norme Can/CSA-Z240 Série MM, Maisons
mobiles au Canada.
(EDVCR)
See-Through
(EDVST)
Peninsula
(EDVPF)
See-Through (EDVST) -
one side flush with a wall
Thisapplianceisonlyforusewiththetypeofgas
indicated on the rating plate. This appliance is
notconvertibleforusewithothergases, unless
a certified kit is used.
Figure 3
TYPICAL LOCATION
Cet appareil doit être utilisé uniquement avec le
type de gaz indiqué sur la plaque signalétique.
Cetappareilnepeutêtreconvertiàd'autresgaz,
sauf si une trousse de conversion est utilisée.
LOCATION
In selecting the location, the aesthetic and functional use of the appliance are primary concerns.
However, vent system routing to the exterior and access to the fuel supply are also important.
CAUTION: Ensure that the cross mem-
bers are not cut or weakened during
installation. The structural integrity of
the manufactured home floor, wall, and
ceiling / roof must be maintained.
Due to high temperatures, the appliance should be located out of traffic and away from furniture
and draperies (Figure 3).
En raison des températures élevées, l’appareil devrait être installé dans un endroit où il y a
peu de circulation et loin du mobilier et des tentures (Figure 3).
CAUTION: This appliance must be ground-
ed to the chassis of the manufactured
home in accordance with local codes or
in the absence of local codes, with the
National Electrical Code ANSI / NFPA 70
- latest edition or the Canadian Electrical
Code CSA C22.1 - latest edition.
The location should also be free of electrical, plumbing or other heating/air conditioning ducting.
These direct-vent appliances are uniquely suited for installations requiring a utility shelf positioned
directly above the fireplace. Utility shelves like these are commonly used for locat-ing television
sets and decorative plants.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Be aware that this is a heat producing ap-
pliance. Objects placed above the unit are
exposed to elevated temperatures.
Vertical Vent Termination Clearances
Termination Heights For Vents
Above Flat Or Sloped Roofs
Ref. NFPA 54 / ANSI Z223.1
TERMINATION HEIGHTS FOR VENTS ABOVE
FLAT OR SLOPED ROOFS
Horizontal Overhang
Do not insulate the space between the appli-
ance and the area above it (see Figure 8 ).
Roof Pitch
Flat to 6/12
* Feet
1.0
*Meters
0.3
2 FT
MIN.
Vertical
Wall
2 FT MIN.
Lowest
Discharge
Opening
Theminimumheightfromthebaseoftheappli-
ance to the underside of combustible materials
used to construct a utility shelf in this fashion
is shown in Figure 8.
6/12 to 7/12
1.25
1.5
0.38
0.46
0.61
0.76
0.99
1.22
1.52
1.83
2.13
2.29
2.44
Vent
Termination
7/12 to 8/12
H*
8/12 to 9/12
2.0
Storm Collar
Flashing
X
12
9/12 to 10/12
10/12 to 11/12
11/12 to 12/12
12/12 to 14/12
14/12 to 16/12
16/12 to 18/12
18/12 to 20/12
20/12 to 21/12
2.5
Roof Pitch is X/12
The appliance should be mounted on a fully
supported base extending the full width and
depth of the unit. The appliance may be located
onornearconventionalconstructionmaterials.
However, if installed on combustible materials,
such as carpeting, vinyl tile, etc., a metal or
woodbarriercoveringtheentirebottomsurface
must be used.
3.25
4.0
1 inch (25.4 mm) Minimum
Clearance to Combustibles
Concentric
Vent Pipe
5.0
*H = MINIMUM HEIGHT FROM ROOF TO
LOWEST DISCHARGE OPENING OF VENT
6.0
The vent / air intake termination clearances
above the high side of an angled roof is as
shown in the following chart:
7.0
7.5
8.0
VENT TERMINATION CLEARANCES
Figure 5
These instructions should be used as a
guideline and do not supersede local codes
in any way. Install venting according to local
codes,theseinstructions,thecurrentNational
Fuel Gas Code (ANSI-Z223.1) in the USA or
the current standards of CAN/CSA-B149.1
in Canada.
Horizontal Vent Termination Clearances
The horizontal vent termination must have a minimum of 6" (152 mm) clearance to any overhead
combustible projection of 2-1/2" (64 mm) or less (see Figure 6). For projections exceeding 2-1/2"
(64 mm), see Figure 6. For additional vent location restrictions refer to Page 7.
Vertical Vent Termination Clearances
Horizontal Vent Termination Clearances
Terminatemultipleventterminationsaccordingto
the installation codes listed above and Figures
4 and 5.
Combustible Projection
2-1/2 inches or less in length
All horizontal terminations
may be located as close as
6” (152mm) to any
(non-combustible and
combustible) exterior
sidewall. This distance
may be decreased to 2”
(51mm) for non-
combustible exterior
sidewalls only, if the
SV4.5HT-2 termination
is used.
Combustible Projection greater
than 2-1/2 inches in length
Ventilated
Soffit
Unventilated
Soffit
12”
(305mm)
Minimum
6"
(152 mm)
18"
12"
(457 mm)
(305 mm)
Termination Kit
Side Elevation View
Termination Kit
Figure 4 - Multiple Terminations
Note - See Figure 42 on Page 22 for the exterior wall recess
allowances of the square horizontal termination.
Figure 6
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERIOR HORIZONTAL VENT TERMINATION CLEARANCE REQUIREMENTS
NOTE: Local Codes Or Regulations
May Require Different Clearances.
* See Item D in the Text Below.
Exterior Wall
P
V
N
N
NOTE: Location Of The Vent Termination
Must Not Interfere With Access To The
Electrical Service.
Inside
Corner Detail
O
*18”
V
G
V
Q
Horizontal
Termination
6”
Inside Corner
Detail D
Ventilated Soffit
A
= 9” in U.S.
= 12” in Canada
A
H
3 ft.
X
B
B
B
D
E
C
C
A
A
V
V
V
Fixed
Operable
Window
L
V
Closed
3 ft.
Window
V
F
J
M
V
C
B
B
C
V
I
A
X
= Air Supply Inlet
V
= Vent Termination
= Area where Termination is not Permitted
Canadian Installation*
US Installation**
12 inches (30cm)**
6 inches (15cm) for appliances
< 10,000 Btuh (3kW), 9 inches (23cm)
for appliances > 10,000 Btuh (3kW) and
< 50,000 Btuh (15kW), 12 inches (30cm)
for appliances > 50,000 Btuh (15kW)**
A = Clearance above grade, veranda, porch, deck, or balcony. 12 inches (30cm)*
B = Clearance to window or door that may be opened.
6 inches (15cm) for appliances
< 10,000 Btuh (3kW), 12 inches (30cm)
for appliances > 10,000 Btuh (3kW)
C = Clearance to permanently closed window
12 inches (305mm) recommended to
prevent window condensation
9 inches (229mm) recommended to
prevent window condensation
D = Vertical clearance to ventilated soffit located above the
termination within a horizontal distance of 18 inches (458mm)
from the center line of the termination
18 inches (458mm)
18 inches (458mm)
E = Clearance to unventilated soffit
12 inches (305mm)
12 inches (305mm)
F = Clearance to outside corner
G = Clearance to inside corner
5 inches (12.7cm) minimum
5 inches (12.7cm) minimum
2 inches (5.08cm) minimum - SV4.5HT-2 2 inches (5.08cm) minimum - SV4.5HT-2
H = Clearance to each inside of center line extended above
meter/regulator assembly
I = Clearance to service regulator vent outlet
3 feet (91cm) within a height of 15 feet
above the meter/regulator assembly*
3 feet (91cm)*
3 feet (91cm) within a height of 15 feet
above the meter/regulator assembly**
3 feet (91cm)**
J = Clearance to nonmechanical air supply inlet to building or 6 inches (15cm) for appliances
6 inches (15cm) for appliances
the combustion air inlet to any other appliance
< 10,000 Btuh (3kW), 12 inches (30cm)
for appliances > 10,000 Btuh (3kW)
< 10,000 Btuh (3kW), 9 inches (23cm)
for appliances > 10,000 Btuh (3kW) and
< 50,000 Btuh (15kW), 12 inches (30cm)
for appliances > 50,000 Btuh (15kW)**
K = Clearance to a mechanical air supply inlet
6 feet (1.83m)*
3 feet (91cm) above if within 10 feet
(3m) horizontally**
L = Clearance above paved sidewalk or paved diveway located 7 feet (2.13m)‡
on public property
7 feet (2.13m)‡
M = Clearance under veranda, porch, deck or balcony
12 inches (30cm)*‡
12 inches (30cm)‡
6 feet (1.83m)**
N = Depth of Alcove (Maximum)
6 feet (1.83m)*
O = Clearance to Termination (Alcove)
P = Width of Alcove (Minimum)
6 inches (15.2mm)*
3 feet (91cm)*
6 inches (15.2mm)**
3 feet (91cm)*
Q = Clearance to Combustible Above (Alcove)
18 inches (457mm)*
18 inches (457mm)**
* In accordance with the current CSA-B149.1 National Gas And Propane Installation Code.
** In accordance with the curent ANSI SZ223.1/NFPA 54 National Fuel Gas Codes.
‡ A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both
dwellings.
*‡ Only permitted if veranda, porch, deck or balcony is fully open on a minimum 2 sides beneath the floor:
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Hearth Extension - A hearth extension is not
required with this appliance. If a hearth exten-
sion is used, do not block the lower control
compartment door. Any hearth extension used
is for appearance only and does not have to
conform to standard hearth extension instal-
lation requirements.
MINIMUM CLEARANCES TO COMBUSTIBLES
Appliance And Vent Clearances
The appliance is approved with zero clearance to combustible materials on all sides (as detailed
in Table 5), with the following exception: When the unit is installed with one side flush with a
wall, the wall on the other side of the unit must not extend beyond the front edge of the unit.
In addition, when the unit is recessed, the side walls surrounding the unit must not extend beyond
the front edge of the unit (see Figure 3).
Shelf Height - To provide for the lowest pos-
sible shelf surface, use the alternate rear vent
outlet,theventingattachedtothetopventshould
be routed in a way to minimize obstructions to
the space above the appliance. Do not insulate
thespacebetweentheapplianceandthearea
above it (see Figure 8). The minimum height
fromthebaseoftheappliancetotheundersideof
combustiblematerialsusedtoconstructautility
shelf in this fashion is shown in Figure 8.
*Note: 3 in. (75 mm) above any horizontal/inclined vent component.
**Note: See Page 10, Step 1 and Figure 12 for clearance requirements to the nailing flange
located at each side of the unit and any screw heads adjacent to it.
Mantel Depth
inches (millimeters)
14 (356)
The appliance should be mounted on a fully
supported base extending the full width and
depth of the unit. The appliance may be located
onornearconventionalconstructionmaterials.
However, if installed on combustible materials,
such as carpeting, vinyl tile, etc., a metal or
woodbarriercoveringtheentirebottomsurface
must be used.
12 (305)
10 (254)
8 (203)
Top of
Appliance
6 (152)
4 (102)
Wall Finishes / Surrounds / Mantels
Note: Combustible wall finish materials and/
or surround materials must not be allowed to
encroach the area defined by the appliance front
face (black sheet metal). Never allow combus-
tible materials to be positioned in front of or
overlapping the appliance face (see Figure 66
on Page 36) and Figure 9 on page 9.
12 10
8
6
4
2
(305) (254) (203) (152) (102) (51)
Front or Rear Face
of Appliance
Figure 7 - Minimum Mantel Clearances
Non-combustible materials, such as surrounds
and other appliance trim, may be installed on
the appliance face with these exceptions: they
must not cover any portion of the removable
glass panel or control compartment.
Shelf Height inches (mm)
Top Vent - with One 90 Degree Elbow Rear Vent - Straight Out the Back
Model No.
Secure Vent
Secure Flex
Secure Vent
Secure Flex
EDVST
EDVPF
EDVCR
EDVCL
Vertical installation clearances to combustible
mantels vary according to the depth of the
mantel. See Figure 7. Mantels constructed of
non-combustible materials may be installed
at any height above the appliance opening;
however, do not allow anything to hang below
the fireplace hood.
53 7/8 (1368)
55 5/8 (1413)
41 1/8 (1045)
41 1/8 (1045)
Do not insulate the
space between the
appliance and the
area above it.
Do not insulate the
space between the
appliance and the
area above it.
Note: We recommend the use of high tem-
perature paint (rated 175° F or higher) on the
underside of the mantel.
Shelf Height
(see table)
Shelf Height
(see table)
Shelf Above Fireplace
With Rear Venting
Shelf Above Fireplace
With Top Venting
Figure 8 - Shelf Height Minimum Clearances
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DETAILED INSTALLATION STEPS
MINIMUM CLEARANCES* Inches (millimeters)
The appliance is shipped with all gas controls
and components installed and pre-wired.
1 - Remove the shipping carton.
2 - Remove the top radiant panel (refer to
Figure 11 ).
3 - Liftthepressurereliefplatesandremove
the cardboard from underneath each of
them.
Back and Sides
1/2 in. (13)
0 (0) from Spacers Or Dimples **
Top Spacers
0 (0)
Floor
From Bottom of Unit To Ceiling
Vent
0 (0)
64 (1626)
3 (76) Top* / 1 (25.4) Sides & Bottom
4 - Open the control compartment access
panel,byactuatingthespring-loadedmagnetic
catches securing the panel, gently depressing
the outer top corners of the panel until the
catches "pop" the panel free and allowing it to
swing out and down to open.
5 - Remove the bottom control compartment
access panel by compressing the spring-
loaded hinge pin on the left side until it
disengages from the left cabinet panel hole.
Pull the panel away from the fireplace. See
Figure 56 on page 30.
6 - Remove the modesty panel by pulling the
bottom right corner of the modesty panel out
slightlytodisengagethesnap-fitfeature;liftthe
modesty panel by the tab on the panel's right
end, pull the right end of the panel away from
the cabinet and then pull the panel diagonally
out of the left side cabinet panel slots. (In
the above procedure, reverse the words "left"
and "right" for EDVCR models). Remove the
modesty panel carefully, so that none of the
wires become loose or disconnected.
7 - Open the two latches (located under the
firebox floor) securing the glass enclosure
panel. Remove the panel by tilting it outward
at the bottom and lifting it up. Set the door
aside protecting it from inadvertent damage.
See Figure 63 on page 34.
SERVICE CLEARANCES Feet (meters)
Front, Back, Sides
3 feet (0.9 meters)
Table 5
Combustible Materials
Allowed In Shaded
Area Safe Zone
WARNING
Top View Of
Fireplace
Failure to position the parts in
accordancewiththesediagrams
or failure to use only parts
specifically approved with this
appliancemayresultinproperty
damage or personal injury.
12"
5"
45°
17"
Min. Distance
To Protected
Side Wall
8-1/4"
Side
Wall
Side
Wall
Min. Distance To
AVERTISSEMENT
14"
Unprotected Side Wall
Risque de dommages ou de
blessures si les pièces ne sont
pas installées conformément à
ces schémas et ou si des pièces
autresquecellesspécifiquement
approuvées avec cet appareil
sont utilisées.
Figure 9
Top Radiant Panel
Top Bustle
Bottom Bustle
Control Compartment Access Panel
Figure 10 Unit Parts Identification
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2. (Page 14) Route gas supply line to
appliance location.
Step 10. (Page 34) Install glass door as-
sembly.
Pressure Relief
Plates
Step 3. Preparing the appliance vent collar
(Page 14).
Step 11. (Page 34) Adjust burner to ensure
proper flame appearance.
REMOVE
CARDBOARD
BEFORE USING
REMOVE
CARDBOARD
BEFORE USING
Step 4. (Page 15) Install the vent system and
Step 12. (Page 36) Install the hoods.
exterior termination.
Step 13. (Page 37) Attach Safety in Operation
Step 5. (Page 27) Field Wiring
Warnings.
Remove Cardboard Before
Using Appliance
a. Millivolt Appliances – Install the operating
control switch (not factory provided) and bring
inelectricalservicelineforforcedair-circulating
blower (optional equipment).
Before proceeding it may be helpful to remove
the log set form the firebox and remove the
embers and volcanic stone from the control
compartment. Refer to the following steps:
Figure 11
b. Electronic Appliances – Field wire and install
operating control switch.
1. Remove the front glass enclosure panel
(see Removing and Installing Glass Enclosure
Panels on Page 34).
TYPICAL INSTALLATION SEQUENCE
Step 6. (Page 28) Install blower kit (optional
equipment).
The typical sequence of installation is outlined
below. However, each installation is unique
and may result in variations to the steps
described.
2. Remove log set box from firebox. Next,
remove embers and volcanic stone from con-
trol compartment. Handle logs carefully to
prevent breakage.
Step 7. (Page 28) Make connection to gas
supply.
See the page numbers references in the follow-
ing steps for detailed procedures.
Step 8. (Page 29) Verifying appliance opera-
tion.
Step 1. FRAMING
FrametheseappliancesasillustratedinFigures
13 (EDVST), 14 (EDVPF), 15 (EDVCL) or 16
(EDVCR). All framing details must allow for
a minimum clearance to combustible framing
members as shown inTable 5 on page 9. If the
appliance is to be elevated above floor level, a
solidcontinuousplatformmustbeconstructed.
Headers may be in direct contact with the
appliance top spacers but must not be sup-
ported by them or notched to fit around them.
All construction above the appliance must be
self supporting, DO NOT use the appliance for
structural support.
Step 1. (Page 10) Construct the appliance
framing. Position the appliance within the
framing and secure with nailing brackets (refer
to Figure 12).
Step 9. (Page 30) Install the logs, decorative
volcanic stone and glowing embers.
EDVST SHOWN
EDVCL SHOWN
(FOR EDVCR VIEW, INTERCHANGE SIDES)
(EDVPF - NO NAILING FLANGES
ON END WITH GLASS PANEL)
Remove these two screws and
use them when installing
the nailing flanges.
Side Nailing Flanges
The fireplace should be secured to the framing
at the side(s) and/or rear of the unit using the
factory-provided nailing flanges. Install the
nailing flanges - 8 (EDVST), 4 (EDVPF, EDVCL
and EDVCR) - as shown in Figure 12 using the
existing screws.
Position the fireplace within the framing. When
required,theflangesmaybebent90degreesby
hand or with the assistance of a hammer. Use
wood screws to secure the nailing flanges to
the framing. See Table 5 on page 9 for clear-
ances of framing members to cabinet parts in
the nailing flange area. The nailing flange itself
is exempt from these clearances.
Nailing Flanges
Turn tabs down and secure to the floor with
8d nails or other appropriate fasteners
on all sides of the unit which do not have
viewing glass panels.
Note: The nailing flanges, combustible members and screw heads located in areas directly adjacent to the nailing
flanges, are EXEMPT from the 1/2” clearance to combustible requirements for the firebox outer wrapper.
Combustible framing may be in direct contact with the nailing flanges and may be located closer than 1/2” from
screw heads and the firebox wrapper in areas adjacent to the nailing flanges. Frame the opening to the exact
dimensions specified in the framing details of this manual.
Floor Nailing Tabs
Secure the fireplace to the floor as shown in
Figure 12.
Figure 12 - Nailing Flanges
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FIREPLACE FRAMING SPECIFICATIONS
11-3/8
(289)
inches (millimeters)
Minimum Framing
Stud Size is 2x4
inches (millimeters)
Minimum Framing
Stud Size is 2x4
EDVST
(See-Through)
11-3/8
10-1/2
EDVPF
(Peninsula)
10-1/2
(267)
(267)
VENT FRAMING -
TOP VENT WITH
ONE 90º ELBOW
VENT FRAMING -
TOP VENT WITH
ONE 90º ELBOW
VENT FRAMING -
REAR VENT WITH
NO ELBOWS
VENT FRAMING -
REAR VENT WITH
NO ELBOWS
7
7
(178)
(178)
12-1/8
(308)
12-1/8
(308)
7
7
(178)
(178)
5-1/8
(130)
5-1/8
(130)
12-1/8
(308)
12-1/8
(308)
A
5-1/8
(130)
26-3/4
(679)
A
26-3/4
(679)
5-1/8
(130)
*41-1/2
(1054)
6-1/4
(159)
*41-1/2
(1054)
Gas Line
Gas Line
6-1/4
(159)
Center of gas line
is 3 in. (76 mm)
up from floor.
Center of gas line
is 3 in. (76 mm)
up from floor.
Dimension A
**22-3/4
(578)
Dimension A
Secure Vent - 47-1/8 (1197)
Secure Flex - 47-3/4 (1213)
**22-3/4
(578)
Secure Vent - 47-1/8 (1197)
***48-1/2
***43-5/8
(1108)
Secure Flex - 47-3/4 (1213) (1232)
***Provide Additional Space For Side Vent
Seal Cap If Installing Against A Solid Wall
***Provide Additional Space For Side Vent
Seal Cap If Installing Against A Solid Wall
**This dimension based on 5/8” drywall.
For 1/2” drywall use 23”.
**This dimension based on 5/8” drywall.
For 1/2” drywall use 23”.
*This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm)
clearance between framing and unit framing spacers. (The 41-1/2 in. dimension permits
easier fireplace installation, if unit is installed after framing is erected.)
*This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm)
clearance between framing and unit framing spacers. (The 41-1/2 in. dimension permits
easier fireplace installation, if unit is installed after framing is erected.)
Figure 13
Figure 14
Dimension A
Dimension A
10-3/8
10-3/8
264
EDVCR (Corner-Right)
inches (millimeters)
Minimum Framing
Stud Size is 2x4
EDVCL (Corner-Left)
Secure Vent - 47-1/8 (1197)
Secure Vent - 47-1/8 (1197)
Secure Flex - 47-3/4 (1213)
(
264)
(
)
Secure Flex - 47-3/4 (1213)
inches (millimeters)
12-1/2
(318)
10-1/2
267
10-1/2
267
VENT FRAMING -
REAR VENT WITH
NO ELBOWS
Minimum Framing
Stud Size is 2x4
(
)
(
)
12-1/2
(318)
VENT FRAMING -
VENT FRAMING -
REAR VENT WITH
NO ELBOWS
5-1/4
(133)
5-1/4 (133)
TOP VENT WITH
ONE 90º ELBOW
VENT FRAMING -
TOP VENT WITH
ONE 90º ELBOW
10-1/2
267
10-1/2
267
(
)
(
)
5-1/4
(133)
5-1/4
(133)
7
7
(178)
(178)
5-1/8
(130)
12-1/8
5-1/8
12-1/8
(308)
(308)
(130)
7
7
(178)
(178)
12-1/8
(308)
12-1/8
(308)
5-1/8
(130)
5-1/8
(130)
26-3/4
(679)
26-3/4
(679)
A
*41-1/2
(1054)
A
Gas Line
*41-1/2
(1054)
Center of gas line
is 3 in. (76 mm)
up from floor.
9-3/4
(248)
6-1/4
(159)
**43-5/8
(1108)
**43-5/8
(1108)
9-7/8
(251)
Gas Line
Optional Gas Line Location
Center of gas line is 3 in. (76 mm)
up from floor.
Center of gas line is
3 in. (76 mm) up from floor.
24
(610)
24
(610)
**Provide Additional Space For Side Vent
**Provide Additional Space For Side Vent
Seal Cap If Installing Against A Solid Wall
Seal Cap If Installing Against A Solid Wall
*This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm) clearance
between framing and unit framing spacers. (The 4-1/2 in. dimension permits easier fireplace
installation, if unit is installed after framing is erected.)
*This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm) clearance
between framing and unit framing spacers. (The 41-1/2 in. dimension permits easier fireplace
installation, if unit is installed after framing is erected.)
Figure 15
Figure 16
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FIREPLACE SPECIFICATIONS
10
(254)
FINISH WALL BRACKET
(Front and back edge of unit top)
EDVST (See-Through)
Figure 17
12 (305)
FRAMING SPACERS
(Top and Both Sides)
1/2
(13)
NOTE - Unit has a factory-installed vent seal
cap and vent cover plate (see Figures 22 and
23 on page 15) in each flue outlet. The vent
seal cap is not shown in this figure.
FLUE
(Top or Side)
5/8
(16)
DETAIL OF
FINISH WALL BRACKET
40-1/8
(1019)
Stepped to Accept Drywall
on All 4 Corners
3-1/2 (89)
1/2 (13)
3-1/2 (89)
1/2 (13)
TOP VIEW
2-1/2
(63.5)
24
(610)
12
(305)
47-1/8
(1197)
4 (102)
10-1/4
(260)
41
(1041)
2-1/2
(63.5)
FLUE
(Top or Side)
37
(940)
ELECTRICAL
INLETS
Provide Additional
Space For Side
Vent Seal Cap If
Installing Against
A Solid Wall
GAS INLET
GAS INLET
ELECTRICAL
INLETS
ELECTRICAL
INLETS
3 (76)
3 (76)
CONTROL
COMPARTMENT
ACCESS PANEL
10-1/2
(267)
6-7/8
(175)
FRONT VIEW
LEFT SIDE VIEW
RIGHT SIDE VIEW
10
(254)
Stepped to Accept Drywall on Two Corners
FINISH WALL BRACKET
(Front, back, and left edge of unit top)
EDVPF (Peninsula)
FRAMING SPACERS
(Top and Side)
Figure 18
12 (305)
NOTE - Unit has a factory-installed vent seal
cap and vent cover plate (see Figures 22 and
23 on page 15) in each flue outlet. The vent
seal cap is not shown in this figure.
DETAIL OF
FINISH WALL BRACKET
1/2
(13)
5/8
(16)
40-1/8
(1019)
3-1/2 (89)
TOP VIEW
2-1/2
(63.5)
12
(305)
24
(610)
43-5/8
(1108)
1/2 (13)
4 (102)
10-1/4
(260)
37
(940)
41
(1041)
Provide Additional
Space For Side
Vent Seal Cap If
Installing Against
A Solid Wall
2-1/2
(63.5)
FLUE
(Top or Side)
ELECTRICAL
INLETS
GAS INLET
3 (76)
CONTROL COMPARTMENT
ACCESS PANEL
6-7/8
(175)
RIGHT SIDE VIEW
LEFT SIDE VIEW
FRONT VIEW
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FIREPLACE SPECIFICATIONS CONTINUED
EDVCL (Corner-Left)
9-1/4
(235)
OPTIONAL GAS INLET
FRAMING SPACERS
10
(254)
Figure 19
(Top, Side and Back)
NOTE - Unit has a factory-installed vent seal
cap and vent cover plate (see Figures 22 and
23 on page 15) in each flue outlet. The vent
seal cap is not shown in this figure.
FLUE
(Top or Side)
12 (305)
DETAIL OF
FINISH WALL BRACKET
1/2
(13)
FINISH WALL BRACKET
(Front and left edge of unit top)
5/8
(16)
40-1/8
(1019)
Stepped to
Accept Drywall
3-1/2
(89)
TOP VIEW
2-1/2
12
1/2
(13)
43-5/8
(1108)
24
(610)
(63.6)
(305)
1/2 13)
4 (102)
10-1/4
(260)
37
(940)
41
(1041)
Provide Additional
Space For Side
Vent Seal Cap If
Installing Against
A Solid Wall
2-1/2
(63.6)
FLUE
OPTIONAL
GAS INLET AT
CABINET REAR
(Top or Side)
ELECTRICAL
INLETS
GAS
INLET
3 (76)
3 (76)
CONTROL COMPARTMENT
ACCESS PANEL
6-7/8
(175)
LEFT SIDE VIEW
FRONT VIEW
RIGHT SIDE VIEW
Gas Line Location
EDVCR (Corner-Right)
10
(254)
9-7/8
(251)
TOP VIEW
Figure 20
FRAMING SPACERS
(Top, Side and Back)
NOTE - Unit has a factory-installed vent seal
cap and vent cover plate (see Figures 22 and
23 on page 15) in each flue outlet. The vent
seal cap is not shown in this figure.
FLUE
(Top or Side)
12 (305)
Stepped to Accept Drywall
DETAIL OF
FINISH WALL BRACKET
FINISH WALL BRACKET
(Front and right edge of unit top)
1/2
(13)
5/8
(16)
40-1/8
(1019)
3-1/2
(89)
2-1/2
(63.5)
24
(610)
43-5/8
(1108)
12
(305)
1/2
(13)
1/2
(13)
4 (102)
10-1/4
(260)
Provide Additional
Space For Side
Vent Seal Cap If
Installing Against
A Solid Wall
41
(1041)
2-1/2
(63.5)
37
FLUE
(Top or Side)
(940)
GAS INLET
AT REAR
OF UNIT
ELECTRICAL
INLETS
3 (76)
6-7/8
(175)
CONTROL COMPARTMENT
ACCESS PANEL
RIGHT SIDE VIEW
FRONT VIEW
LEFT SIDE VIEW
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installingagassupplylinefromthefuelsupplyto
theapplianceinvolvesnumerousconsiderations
of materials, protection, sizing, locations, con-
trols,pressure,sediment,andmore.Certainlyno
one unfamiliar and unqualified should attempt
sizing or installing gas piping.
IMPORTANT:Ifpropaneisused,beawarethat
if tank size is too small (i.e. under 100-lbs, if
this is the only gas appliance in the dwelling.
Ref. NPFA 58), there may be loss of pressure,
resulting in insufficient fuel delivery (which
can result in sooting, severe delayed ignition
orothermalfunctions). Anydamageresulting
from an improper installation, such as this, is
not covered under the limited warranty.
Step 2. ROUTING GAS LINE
Route a 1/2" (13 mm) gas line to the left side
of the appliance as shown in Figure 21. Gas
lines must be routed, constructed and made
of materials that are in strict accordance with
local codes and regulations. All appliances
are factory-equipped with a flexible gas line
connector and 1/2 inch shutoff valve. (See
Step 7 on Page 28).
Schedule 40
Black Iron Pipe
Inside Diameter (Inches)
Step 3. PREPARING THE APPLIANCE
VENT COLLAR
Schedule 40 Pipe
Length (feet)
Natural
Gas
Propane
Gas
0-10
10-40
1/2
1/2
1/2
3/4
3/4
3/8
1/2
1/2
1/2
1/2
WARNING
40-100
Failure to reinstall and securely
tighten vent seal cap screws
could result in leakage of flue
products into the living space.
Vent seal cap must remain
securely installed on unused
vent collar. Failure to do so
could result in leakage of flue
products into living space.
100-150
150-200
Table 6
3-1/8"
(79 mm)
5-5/8"
(143 mm)
Notes:
Also see Figures 13 and 14.
• All appliances are factory-equipped with
a flexible gas line connector and 1/2 inch
shutoff valve.
Figure 21 - Route Gas Line
• SeeMassachusettsRequirementsonPage
4 foradditionalrequirementsforinstallations
in the state of Massachusetts in the USA.
• ThegassupplylineshouldNotbeconnected
to the appliance until Step 7 (Page 28).
• Apipejointcompoundratedforgasshouldbe
usedonthethreadedjoints.Ensurepropane
resistant compounds are used in propane
applications. Be very careful that the pipe
compound does not get inside the pipe.
• It is recommended to install a sediment
trap in the supply line as close as possible
to the appliance. Appliances using Propane
should have a sediment trap at the base of
the tank.
Proper Sizing of Gas Line
REMOVE VENT SEAL CAP
(From the vent that will be used only)
Properly size and route the gas supply line
from the supply regulator to the area where the
appliance is to be installed per requirements
outlined in the National Fuel Gas Code, NFPA
54 - latest edition (USA) or CAN/CSA-B149.1
- latest edition (Canada).
Top Vent Installations - See Figure 22
Side Vent Installations - See Figure 23
Preparing the Appliance Vent Collar
Each of the appliances' two vent collars are
sealed with a seal cap which must be removed
fromtheventcollarbeingused. RefertoFigure
22 for top vent installations and Figure 23 for
sideventinstallationsandthefollowingstepsto
prepare the appropriate collar for use.
Never use galvanized or plastic pipe. Refer to
Table 6 for proper sizing of the gas supply line,
if black iron pipe is being used. Gas lines must
be routed, constructed and made of materials
that are in strict accordance with local codes
andregulations. Werecommendthataqualified
individual such as a plumber or gas fitter be
hired to correctly size and route the gas supply
line to the appliance.
• Check with local building official for local
code requirements (i.e. are below grade
penetrations of the gas line allowed?, etc).
From the vent collar being used, remove the
two screws securing the vent seal cap. Twist
the cap counterclockwise. Pull it away from
the appliance and discard, along with the piece
of insulation.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4. INSTALL THE VENT SYSTEM
General Information
Securing Screws
Top Vent
Vent Seal Cap
(OUTSIDE of
Appliance)
Theseinstructionsshouldbeusedasaguidelineanddonotsupersede
local codes in any way. Install venting according to local codes, these
instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the
USA or the current standards of CAN/CSA-B149.1 in Canada.
Insulation
Cabinet Top
Ensure clearances are in accordance with local installation codes and
the requirements of the gas supplier.
CROSS SECTION
Firebox Top
Dégagement conforme aux codes d'installation locaux et aux exigences
du foumisseunde gaz.
(INSIDE of Appliance)
TOP VENT SEAL CAP REMOVAL
(TOP VENT INSTALLATIONS ONLY)
Use only approved venting components. See Approved Vent
Components on Page 2.
Figure 22 -
These fireplaces must be vented directly to the outside.
Vent Seal Cap
Insulation
The vent system may not service multiple appliances, and must never
be connected to a flue serving a solid fuel burning appliance. The vent
pipe is tested to be run inside an enclosed wall (such as a chase). There
is no requirement for inspection openings in the enclosing wall at any of
the joints in the vent pipe.
CROSS SECTION
(OUTSIDE of
Appliance)
(INSIDE of
Appliance)
Installation of Vent Restrictor
A vent restrictor may be needed with this appliance. The restrictor is
installed in the appliance top flue outlet as shown in Figure 24, either
before adding vent, from above, or after installation of vent from below,
within the firebox. The restrictor is self securing through a positive
friction fit.
Side Vent
Securing Screws
Cabinet Back
SIDE VENT SEAL CAP REMOVAL
(SIDE VENT INSTALLATIONS ONLY)
Determine the venting for the appliance. If the vent run will include at
least 8 feet of vertical rise, then install the restrictor in the appliance
collar before connecting any vent (Refer to Figure 24 ). Place the
restrictor inside the appliance vent collar and press in place.
Figure 23 -
VENT RESTRICTOR INSTALLATION
Note: The restrictor is included within the firebox.
A vent restrictor may be needed when vertically terminating the vent
system above the roof (when using the appliance top vent), install a vent
restrictor in the top vent of the fireplace outlet.
Select Venting System - Horizontal or Vertical
With the appliance secured in framing, determine vent routing and identify
the exterior termination location. The following sections describe vertical
(roof) and horizontal (exterior wall) vent applications. Refer to the section
relating to your installation. A list of approved venting components are
shown on Pages 38 and 39.
If needed, install the restrictor as shown, either from inside or outside the
unit, in the inner fireplace collar.
Restrictor
Inner
Fireplace
Collar
Appliance
Vent Outlet
Top Shown - Rear Similar
Figure 24
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
VERTICAL TERMINATION SYSTEMS (ROOF)
VENT SECTION LENGTH CHART
VENT SECTION LENGTH CHART
Nominal
T
O
T
A
L
T
O
T
A
L
Nominal Section
6
12
24
36
48
Section Length
6
12
24
36
48
Length (inches)
See Figure 25 and Figures 35 through 39
on Pages 19 and 20 and their associated
Vertical Vent Tables which illustrate the various
verticalventingconfigurationsthatarepossible
for use with these appliances. Secure Vent™
pipe applications are shown in these Figures;
SecureFlex™pipemayalsobeused. AVertical
VentTablesummarizeseachsystem’sminimum
and maximum vertical and horizontal length
values that can be used to design and install the
vent components in a variety of applications.
(inches)
Net Section
4-1/2 10-1/2 22-1/2 34-1/2 46-1/2
Number of Vent Sections
Net Section
Length (inches)
4-1/2 10-1/2 22-1/2 34-1/2 46-1/2
Number of Vent Sections
Length (inches)
Height of Vent
Height of Vent
Q
T
Q
T
inches
144
ft
inches
4.5
ft
Y
Y
12
1
0
1
0
0
1
0
0
1
0
0
0
1
0
1
1
2
0
0
1
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
5
5
5
0
0
0
5
6
6
3
3
3
3
0
0
0
4
4
4
0
0
0
4
4
5
5
5
6
6
4
5
5
7
6
7
0.375
0.75
1
2
0
1
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
1
2
1
2
9
150
12.5
10.5 0.875
15 1.25
19.5 1.625
21 1.75
154.5 12.875
160.5 13.375
172.5 14.375
0
0
2
1
0
0
3
0
0
1
0
0
1
2
0
2
3
0
1
0
1
0
0
0
1
0
0
0
0
1
0
0
0
0
0
0
0
2
1
3
3
1
3
177
183
186
14.75
15.25
15.5
22.5 1.875
25.5 2.125
31.5 2.625
34.5 2.875
37.5 3.125
Both these vertical vent systems terminate
through the roof. The minimum vent height
above the roof and/or adjacent walls is speci-
fied in ANSI Z223.1-(latest edition) (In Canada,
the current CAN/CSA-B149.1 installation code)
by major building codes. Always consult your
localcodesforspecificrequirements.Ageneral
guide to follow is the Gas Vent Rule (refer to
Figure 5 on Page 6).
190.5 15.875
196.5 16.375
205.5 17.125
43.5 3.625
0
0
0
1
2
0
0
0
1
2
0
2
0
0
0
0
0
0
1
0
3
2
1
3
207
17.25
45
3.75
211.5 17.625
46.5 3.875
49.5 4.125
217.5 18.125
229.5 19.125
232.5 19.375
0
0
0
1
0
1
0
0
0
0
1
1
0
0
0
1
0
1
0
0
1
0
1
0
0
1
0
1
0
0
0
0
0
1
0
0
0
0
0
1
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
1
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
6
6
0
0
5
5
0
0
0
0
0
6
0
6
6
6
0
0
7
7
7
0
0
8
8
0
9
9
7
7
Vertical (Straight) Installation
(Figure 25)
51
4.25
1
0
0
0
0
0
1
1
0
0
0
0
0
1
1
0
1
0
2
0
0
0
0
1
0
2
0
0
0
0
0
2
1
2
3
0
3
0
0
0
1
2
0
1
0
0
0
1
0
0
2
0
2
2
1
0
0
0
2
0
1
0
0
0
0
0
0
0
0
1
1
1
2
0
2
2
3
2
4
3
2
4
3
3
2
4
3
2
4
3
0
5
55.5 4.625
237
19.75
0
6
Determine the number of straight vent sec-
tions required. 4-1/2" (114 mm), 10-1/2" (267
mm), 22-1/2" (572 mm), 34-1/2" (876 mm)
and 46-1/2" (1181 mm) net section lengths
are available (see Tables on this page and
Page 38 - Rigid Vent Sections). Plan the vent
lengths so that a joint does not occur at the
intersection of ceiling or roof joists. Refer to
the Vent Section Length Chart.
57
66
4.75
5.25
241.5 20.125
7
7
246
252
264
276
279
20.5
21
7
8
67.5 5.625
7
8
69
72
5.75
6
22
7
8
23
8
8
73.5 6.125
79.5 6.625
23.25
0
6
280.5 23.375
283.5 23.625
289.5 24.125
301.5 25.125
310.5 25.875
8
9
81
90
6.75
7.5
0
7
0
7
SV4.5CGV-1
91.5 7.625
0
7
SV4.5FA OR
Termination
SV4.5FB Flashing
AND SV4.5SC
93
96
7.75
8
9
9
315
26.5
9
10
7
STORM COLLAR
97.5 8.125
102 8.5
103.5 8.625
325.5 27.125
0
2
0
1
0
0
0
0
0
0
0
3
3
2
0
0
4
3
4
330
336
345
27.5
28
0
8
0
8
108
114
117
9
1" (25.4 mm)
Minimum
Clearance to
Combustibles
28.75
10
10
0
10
11
8
9.5
9.75
0
1
1
0
1
0
0
0
1
2
0
1
0
0
0
0
0
0
0
5
0
1
1
6
0
0
0
0
0
3
3
3
0
4
0
4
2
0
0
0
0
0
0
3
0
4
6
5
4
5
6
4
3
5
349.5 29.125
372 31
118.5 9.875
126 10.5
130.5 10.875
376.5 31.375
379.5 31.625
418.5 34.875
0
9
*SV4.5VF
Firestop/Spacer
11
0
11
9
135
138
11.25
11.5
423
465
35.25
38.75
0
10
0
10 10
139.5 11.625
142.5 11.875
40' Max
(12.2 M)
SV4.5L6/12/24/36/48
Vent Sections
Effective Vent Length
Note: Convert inches into metric equivalent
measurement, as follows:
Model
Effective Length
*When using Secure Flex,
use Firestop/Spacer
SF4.5VF
SV4.5L6
SV4.5L12
SV4.5L24
SV4.5L36
SV4.5L48
4-1/2"
10-1/2"
22-1/2"
34-1/2"
46-1/2"
Millimeters (mm) = Inches x 25.4
Centimeters (cm) = Inches x 2.54
Meters (M) = Inches x .0254
Figure 25
Table 7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Vertical (Offset) Installation
B. Attach vent components to appliance -
Secure Vent SV4.5 direct vent system compo-
nents are unitized concentric pipe components
featuring positive twist lock connections (see
Figures 27 and 28 ).
C. Attach vent components to each other
- Other vent sections may be added to the
previously installed section in accordance with
the requirements of the vertical vent figures
and tables. To add another vent component
to a length of vent run, align the dimpled end
over the inclined channel end of the previously
installed section, adjusting the radial alignment
until the four locking dimples are aligned with
the inlets of the four incline channels of the
previous section.
Analyze the vent routing and determine the
quantities of vent sections and number of
elbowsrequired.RefertoVerticalVentFigures
and Tables on page 16 to select the type of
vertical installation desired. Vent sections are
available in net lengths of 4-1/2" (114 mm),
10-1/2" (267 mm), 22-1/2" (572 mm), 34-1/2"
(876 mm) and 46-1/2" (1181 mm). Refer to the
Effective Vent Length Chart Table 7 on page
16 for an aid in selecting length combinations.
Elbows are available in 90° and 45° configura-
tions. Refer to Figure 30 for the SV4.5E45 and
SV4.5E90 elbow dimensional specifications.
All of the appliances covered in this document
are fitted with collars having locking inclined
channels. The dimpled end of the vent com-
ponents fit over the appliance collar to create
the positive twist lock connection.
Push the vent component against the previous
section until it fully engages, then twist the
componentclockwiserunningthedimplesdown
and along the incline channels until they seat at
the end of the channels.This seating position
is indicated by the alignment of the arrow and
dimple as shown in Figure 28.
First Vent
Component
Align the dimple (four places)
with the opening of the locking
incline channel on appliance
collar. Twist vent component
clockwise to engage and seal.
Where required, a telescopic vent section
(SV4.5LA) may be used to provide the installer
withanoptionininstallingintightand confined
spaces or where the vent run made up of fixed
length pieces develops a joint in a undesirable
location, or will not build up to the required
length. The SV4.5LA Telescopic Vent Section
has an effective length of from 1-1/2" (38 mm)
to 7-1/2" (191 mm). The SV4.5LA is fitted with
a locking inclined channel end (identical to a
normalventsectioncomponent)andaplainend
with 3 pilot holes. Slip the plain end over the
locking channel end of a standard SV4.5 vent
component the required distance and secure
with three screws.
Dimple
Locking
Incline Channel
D. Install firestop/spacer at ceiling (Figure
29 ) - When using Secure Vent, use SV4.5VF
firestop/spacer at ceiling joists; when using
Secure Flex, use SF4.5VF firestop/spacer. If
there is living space above the ceiling level,
the firestop/spacer must be installed on the
bottom side of the ceiling. If attic space is
above the ceiling, the firestop/spacer must
be installed on the top side of the joist. Route
the vent sections through the framed opening
and secure the firestop/spacer with 8d nails
or other appropriate fasteners at each corner.
Remember to maintain 1" (25 mm) clearance
to combustibles, framing members, and attic
or ceiling insulation when running vertical
chimney sections. Attic insulation shield
(96K94) may be used to obtain the required
clearances indicated here. See installation
accessories tables on pages 38 and 39.
Appliance collar
Vent / Appliance Collar
Connection
Figure 27
Arrow
Align the dimple (four places) of the
upper vent section with the opening of
the locking incline channel on the
lower vent section. Twist vent
component clockwise to engage and
seal until arrow and dimple align.
Dimple
Maintain a minimum 1" (25 mm) clearance to
combustiblematerialsforallverticalelements.
Clearances for all horizontal elements are 3"
(76 mm) on top, 1" (25 mm) on sides and 1"
(25 mm) on the bottom.
Locking
Incline Channel
Connected
Vent Sections
Arrow
Vent / Vent Section
Connection
Arrow
A. Frame ceiling opening - Use a plumb line
from the ceiling above the appliance to locate
center of the vertical run. Cut and/or frame an
opening, 10-1/2" x 10-1/2" (267mm x 267mm)
inside dimensions, about this center mark
(Figure 26 ).
Figure 28
SV4.5CGV-1
SV4.5FA or
Termination
SV4.5FB Flashing
and SV4.5SC
Storm Collar
To attach a vent component to the appliance
collar, align the dimpled end over the collar,
adjusting the radial alignment until the four
locking dimples are aligned with the inlet of
the four inclined channels on the collar (refer to
Figure 27 ). Push the vent component against
the collar until it fully engages, then twist the
component clockwise, running the dimples
down and along the incline channels until they
seat at the end of the channels. The unitized
design of the Secure Vent components will
engage and seal both the inner and outer pipe
withouttheneedforsealantorscrews. Ifdesired
a #6 x 1/2" screw may be used at the joint, but
it is not required as the pipe will securely lock
when twisted.
1” (25.4 mm)
Minimum
10-1/2" Min.
(267 mm)
vWhen
using
Clearance to
Combustibles
secure
Flex, use
Firestop/
Spacer
vSV4.5VF
Firestop / spacer
Ceiling
Framing
SF4.5VF
10-1/2" Min.
(267 mm)
uSV4.5SP
Support Plate
8 ft. (2.4 M)
Maximum
uSV4.5SU
Support Strap
Shown With
uSecured
Note: An elbow may also be attached to the
appliance collar. Attach in the same manner
as you would a vent section.
Optional
Radiant
Panels
to Vent with
Appropriate
Fasteners
Figure 26
Figure 29
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
F.Changeventdirectiontohorizontal/inclined
run - At transition from or to a horizontal/in-
clined run, install the SV4.5E45 and SV4.5E90
elbows in the same manner as the straight vent
sections. The elbows feature a twist section to
allow them to be routed about the center axis
of their initial collar section to align with the
required direction of the next vent run element.
Twist elbow sections in a clockwise direction
only so as to avoid the possiblity of unlocking
anyofthepreviouslyconnectedventsections.
See Figure 30.
H. Frame roof opening - Identify location for
vent at the roof. Cut and/or frame opening per
Roof Framing Chart and Figure 31.
Storm
Collar
C
D
E. Support the vertical vent run sections -
Note-Properventingsupportisveryimportant.
The weight of the vent must not be supported
by the fireplace in any degree.
Figure 33
Framing Dimensions for Roof
K. Install the vertical termination - The final
step involves installation of the SV4.5CGV-1
Vertical Termination. Extend the vent sections
to the height as shown in the "Vertical vent ter-
mination section" on page 6. The SV4.5CGV-1
Vertical Termination (Figure 34 ) installs in the
exact same fashion as any other Secure Vent
section. Align the termination over the end of
the previously installed section, adjusting the
radial alignment until the four locking dimples
of the termination are aligned with the inlets of
thefourinclinechannelsofthelastventsection.
Pushtheterminationdownuntilitfullyengages,
thentwisttheterminationclockwiserunningthe
dimples down and along the incline channels
until they seat at the end of the channels.
Pitch
0/12
C
D
Support the vertical portion of the venting
system every 8 feet (2.4m) above the fireplace
vent outlet. One method of support is by utiliz-
ing field provided support straps (conventional
plumber's tape). Secure the plumber's tape to
theframingmemberswithnailsorscrews.Loop
the tape around the vent, securing the ends of
the tape to the framing. If desired, sheet metal
screws #6 x 1/2" length may be used to secure
the support straps to the vent pipe. Refer to
Figure 29.
10-1/2 in.
10-1/2 in.
(267 mm) (267 mm)
10-1/2 in. 12 in.
(267 mm) (305 mm)
10-1/2 in. 17-3/4 in.
(267 mm) (451 mm)
6/12
12/12
Figure 31
I. Install the roof flashing - Extend the vent
sections through the roof structure. Install the
roof flashing over the vent section and posi-
tion such that the vent column rises vertically
(use carpenters level) (Figure 32). Nail along
perimeter to secure flashing or adjust roofing
to overlap the flashing edges at top and sides
only and trim where necessary. Seal the top
and both sides of the flashing with waterproof
caulking.
8-1/8"
4-13/16"
(206 mm)
(122 mm)
Swivel Joint
(360° swivel)
Swivel Joint
(360° swivel)
SV4.5E45
SV4.5E90
(45 Elbow)
°
(90 Elbow)
°
Figure 30
G.Continueinstallationofhorizontal/inclined
sections - Continue with the installation of the
straight vent sections in horizontal/inclined run
as described in Step C. Install support straps
every5'(1.52m)alonghorizontal/inclinedvent
runs using conventional plumber’s tape. It is
very important that the horizontal/inclined
run be maintained in a straight (no dips) and
slightly elevated plane in a direction away
from the fireplace 1/4" per foot (20 mm per
meter) of horizontal vent. Use a carpenter’s
level to measure from a constant surface and
adjust the support straps as necessary.
Figure 34
Figure 32
If the vent system extends more than 5' (1.5
m) above the roof flashing, stabilizers may be
necessary. Additional screws may be used at
section joints for added stability. Guide wires
may be attached to the joint for additional sup-
port on multiple joint configurations.
J. Install the storm collar - Install the storm
collar, suppliedwiththeflashing, overthevent/
flashingjoint.SeeFigure33.Loosenthestorm
collar screw. Slide collar down until it meets
the top of the flashing. Tighten the adjusting
screw. Apply non-combustible caulking or
mastic around the circumference of the joint
to provide a water tight seal.
It is important to maintain the required clear-
ancestocombustibles:1"(25mm)atallsides
forall vertical runs; and 3" (76 mm) at the top,
1" (25 mm) at sides, and 1" (25 mm) at the
bottom for all horizontal/inclined runs.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
VERTICAL VENT FIGURES/TABLES
Table A
V Minimum
Note: Secure Vent (rigid vent pipe) is shown
in the figures; Secure Flex (flexible vent pipe)
may also be used.
H Maximum
feet (meter)
uCeiling Firestop / Spacer (SV4.5VF)
feet
(meter)
(0.305)
(0.610)
(0.914)
(1.219)
Note: It is very important that the horizontal/
inclined run be maintained in a straight (no
dips) and recommended to be in a slightly
elevated plane, in a direction away from the
fireplace of 1/4" rise per foot (20 mm per meter)
which is ideal, though rise per foot run ratios
that are smaller are acceptable all the way down
to at or near level.
2
4
6
8
(0.610)
(1.219)
(1.829)
(2.438)
1
2
3
4
V
V + H = 40 feet (12.2 meters) Max.
H = 8 feet (2.4 meters) Max.
Ratio V to H ratio is 1:2
Note: SV4.5VF (Secure Vent), SF4.5VF (Secure
Flex)firestop/spacermustbeusedanytimevent
pipepassesthroughacombustiblefloororceil-
ing. SV4.5HF (Secure Vent), SF4.5HF (Secure
Flex)firestop/spacermustbeusedanytimevent
pipe passes through a combustible wall.
uWhen using Secure Flex, use Firestop /
H
Spacer SF4.5VF.
Example: If 8 feet of (H) horizontal vent run is needed, then 4 feet minimum (V) vertical vent will be
required.
This table shows a 1(V) to 2(H) ratio. For every 1 foot of (V) vertical, you are allowed 2 feet of (H)
horizontal run, up to a maximum horizontal run of 8 feet.
Note: Two 45 degree elbows may be used in
place of one 90 degree elbow. The same rise
to run ratios, as shown in the venting figures
for 90 elbows, must be followed if 45 degree
elbows are used.
Figure 36 - Side Vent - ONE 90 DEGREE ELBOW
Note: An elbow is acceptable as 1 foot of
vertical rise, except where an elbow is the
only vertical component in the system. (See
Figure 44 on page 23 ).
Table B
H Maximum
feet (meter)
V Minimum
feet (meter)
Elbow Only
H
5
(1.524)
(1.524)
(3.048)
(4.572)
(6.096)
WARNING
Undernocircumstances,maysepa-
rate sections of concentric flexible
vent pipe be joined together.
5
1
(0.305)
(0.610)
(0.914)
(1.219)
10
15
20
2
3
4
Ceiling Firestop /
Spacer (SV4.5VF)
u
V + V + H = 40 feet (12.2 m) Max.
1
H = 20 feet (6.096 meters) Max.
uCeiling Firestop /
Spacer (SV4.5VF)
Example: If 20 feet of (H) hori-
zontal vent run is needed, then 4
feet minimum of (V) vertical vent
will be required.
V1
This table shows a 1(V) to 5(H)
V
ratio. Forevery1footof(V)verti-
cal, you are allowed 5 feet of (H)
horizontal run, up to a maximum
horizontal run of 20 feet.
40 feet
(12.2 meters)
Maximum
A Vent Restrictor as
shown in Figure 24,
must be used in this
application.
An elbow is acceptable as 1 foot
of vertical rise except where
an elbow is the only vertical
component in the system. See
Figure 44.
Wall Firestop/
v
Spacer (SV4.5HF)
uWhen using Secure Flex, use
vWFirheesntoupsi/nSgpSaecceurrSeFF4l.e5xV,Fu.se
Firestop / Spacer SF4.5HF.
Figure 37 - Top Vent - TWO 90 DEGREE ELBOWS
WhenusingSecureFlex,use
Firestop/Spacer SF4.5VF
u
Figure 35 - Top Vent - STRAIGHT
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
VERTICAL VENT FIGURES / TABLES (CONTINUED)
Table C
H1
H+H Maximum
HMaximum
V Minimum
1
feet (meter) feet (meter)
feet
(meter)
(0.305)
(0.610)
(0.914)
(1.219)
Ceiling Firestop /
u
5
(1.524)
(3.048)
(4.572)
(6.096)
2
4
6
8
(0.610)
(1.219)
(1.829)
(2.438)
1
2
3
4
Spacer (SV4.5VF)
10
15
20
V + V + H + H = 40 feet (12.2 m) Max
H = 8 feet (2.438 meters) Max.
Wall Firestop/
v
1
1
Spacer (SV4.5HF)
V1
H + H = 20 feet (6.096 meters) Max.
1
Ceiling Firestop /
u
Spacer (SV4.5VF)
uWhen using Secure Flex, use Firestop / Spacer SF4.5VF
vWhen using Secure Flex, use Firestop / Spacer SF4.5HF
Example: If 20 feet total (H+H1) horizontal vent run is needed,
then 4 feet minimum of (V) vertical vent will be required.
This table shows a 1(V) to 5(H) ratio. For every 1 foot of (V)
vertical, you are allowed 5 feet of (H+H1) horizontal run up to a
maximum total horizontal run of 20 feet.
V
H
Figure 38 - Side Vent - THREE ELBOWS
Table D
V Minimum
(meter)
Elbow Only
(0.305)
H + H Maximum
1
feet
(meter)
(1.524)
(1.524)
(3.048)
(4.572)
(6.096)
feet
Ceiling
5
u
Firestop / Spacer
(SV4.5VF)
V
1
5
1
2
3
4
Wall Firestop/
v
Spacer (SV4.5HF)
10
15
20
(0.610)
(0.914)
(1.219)
H
H + H = 20 feet (6.096 m) Max.
1
V + V + H + H = 40 ft. (12.192 m) Max.
V
1
1
H
1
uWhen using Secure Flex, use Firestop / Spacer SF4.5VF
vWhen using Secure Flex, use Firestop / Spacer SF4.5HF
Example: If 20 feet total (H+H1) horizontal vent run is needed, then 4 feet minimum
of (V) vertical vent will be required.
This table shows a 1(V) to 5(H) ratio. For every 1 foot of (V) vertical, you are allowed
5 feet of (H+H1) horizontal run up to a maximum total horizontal run of 20 feet.
An elbow is acceptable as 1 foot of vertical rise except where an elbow is the only
vertical component in the system. See Figure 44.
Figure 39- Top Vent - THREE ELBOWS
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HORIZONTAL (OUTSIDE WALL)
TERMINATION SYSTEM
Support
Brackets
Horizontal / Inclined Run
Building
Support
Framing
Figures 40, and Figures 43 to 48 on pages
23 to 25 and their associated Horizontal Vent
Table illustrate the various horizontal venting
configurations that are possible for use with
theseappliances. SecureVentpipeapplications
are shown in these figures; Secure Flex pipe
may also be used. A Horizontal Vent Table sum-
marizeseachsystem’sminimumandmaximum
vertical and horizontal length values that can be
used to design and install the vent components
in a variety of applications.
SV4.5HT-2
Termination
Shown
SV4.5E90
Elbow
SV4.5L6/12/24/36/48
Exterior
Wall
Vent Sections
Ceiling
uFirestop / Spacer
SV4.5VF
Vertical
Rise
Support Bracket Spacing
Every 5 ft (1.52 m)
uWhen Using Secure Flex,
Use Firestop / Spacer SF4.5VF
SV4.5HT-2
Termination
Shown
See Figure 29 on Page 17 for
Bothofthesehorizontalventsystemsterminate
through an outside wall. Building Codes limit or
prohibit terminating in specific areas. Refer to
Figure 6 and page 7 for location guidelines.
vertical vent section support.
Fireplace
Shown With Optional Radiant Panels
SecureVentSV4.5directventsystemcomponents
areunitizedconcentricpipecomponentsfeaturing
positivetwistlockconnection,(refertoFigure28
on page 17). All of the appliances covered in this
document are fitted with collars having locking
inclined channels. The dimpled end of the vent
componentsfitovertheappliancecollartocreate
the positive twist lock connection.
Figure 40 -TYPICAL HORIZONTAL VENT INSTALLATION
G. Support the vertical run sections -
The unitized design of the Secure Vent compo-
nents will engage and seal both the inner and
outer pipe elements with the same procedure.
Sealant and securing screws are not required.
On the vertical run, support the venting sys-
tem every 8 feet (2.4m) above the fireplace
vent outlet with field provided support straps
(Plumber's tape). Attach the straps to the vent
pipe and secure to the framing members with
nails or screws. See Figure 29 on page 17.
Note: An elbow may also be attached to the
appliance collar. Attach in the same manner
as you would a vent section.
A. Plan the vent run -
Analyze the vent routing and determine the
types and quantities of sections required
4-1/2" (114 mm), 10-1/2" (267 mm), 22-1/2" (572
mm),34-1/2"(876mm)and46-1/2"(1181mm)net
section lengths are available. It is recommended
that you plan the venting so that a joint does not
occur intheceilingorroof joists. Allowforelbows
as indicated in Figure 30 on page 18.
H. Change vent direction - At transition
from or to a horizontal/inclined run, install the
SV4.5E45 and SV4.5E90 elbows in the same
manner as the straight vent sections. The
elbows feature a twist section to allow them
to be routed about the center axis of their
initial collar section to align with the required
direction of the next vent run element. Twist
elbow sections in a clockwise direction only
so as to avoid the possiblity of unlocking any
of the previously connected vent sections.
See Figure 30 on page 18.
E. Attachventcomponentstoeachother-Other
vent sections may be added to the previously
installed section in accordance with the require-
ments of the vent tables. To add another vent
component to a length of vent run, align the
dimpled end of the component over the inclined
channel end of the previously installed section,
adjustingtheradialalignmentuntilthefourlock-
ingdimplesarealignedwiththeinletsofthefour
incline channels of the previous section. Push
theventcomponentagainsttheprevioussection
until it fully engages, then twist the component
clockwise running the dimples down and along
the incline channels until they seat at the end of
the channels.Thisseatingpositionisindicated
by the alignment of the arrow and dimple as
shown in Figure 28 on page 17.
Maintain a minimum 1" (25 mm) clearance to
combustiblesontheverticalsections.Clearances
forthehorizontalrunsare;3"(76mm)ontop,1"(25
mm) on sides, and 1" (25 mm) at the bottom.
B. Frame exterior wall opening -
Locate the center of the vent outlet on the exterior
wallaccordingtothedimensionsshowninFigures
13, through 16 on page 11. Cut and/or frame an
opening, 10-1/2" x 12-1/8" (267 mm x 308mm)
inside dimensions, about this center.
I. Continueinstallationofhorizontal/inclined
sections - Continue with the installation of the
straightventsectionsinhorizontal/inclinedrun
as described in Step E. Install support straps
every 5 ft. (1.52 m) along horizontal/inclined
vent runs using conventional plumber’s tape.
See Figure 40, it is very important that the
horizontal/inclined run be maintained in a
straight (no dips) and recommended to be in
a slightly elevated plane, in a direction away
from the fireplace of 1/4" rise per foot (20 mm
per meter) which is ideal, though rise per foot
runratiosthataresmallerareacceptableallthe
way down to at or near level. Use a carpenter’s
level to measure from a constant surface and
adjust the support straps as necessary.
C. Frame ceiling opening - If the vertical route
istopenetrateaceiling, useplumblinetolocate
thecenterabovetheappliance.Cutand/orframe
an opening, 10-1/2" x 10-1/2" (267 mm x 267
mm)insidedimensions,aboutthiscenter(refer
to Figure 26 on page 17 ).
F. Install firestop/spacer at ceiling -
WhenusingSecureVent,useSV4.5VFfirestop/
spaceratceilingjoists;whenusingSecureFlex,
use SF4.5VF firestop/spacer. If there is living
space above the ceiling level, the firestop/
spacer must be installed on the bottom side of
the ceiling. If attic space is above the ceiling,
the firestop/ spacer must be installed on the
top side of the joist. Route the vent sections
through the framed opening and secure the
firestop/spacerwith8dnailsorotherappropriate
fasteners at each corner.
D. Attach vent components to appliance - To
attach a vent component to the appliance collar,
alignthedimpledendoverthecollar,adjustingthe
radialalignmentuntilthefourlockingdimplesare
alignedwiththeinletsofthefourinclinechannels
on the collar (refer to Figure 27 on page 17 ).
It is important to maintain the required clear-
ancestocombustibles:1"(25mm)atallsides
forallverticalruns;and 3" (76mm)atthetop,
1" (25 mm) at sides, and 1" (25 mm) at the
bottom for all horizontal/inclined runs
Remember to maintain 1" (25 mm) clearance
to combustibles, framing members, and attic
or ceiling insulation when running vertical
chimney sections.
Push the vent component against the collar until it
fullyengages,thentwistthecomponentclockwise,
runningthedimplesdownandalongtheinclinechan-
nels until they seat at the end of the channels.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
J. Assemble vent run to exterior wall - If not
previously measured, locate the center of the
vent at the exterior wall. Prepare an opening as
described in Step B. Assemble the vent system
to point where the terminus of the last section
is within 7 in. (178 mm) to 11-1/4 in. (286
mm) inboard of the exterior surface to which
the SV4.5 HT termination is to be attached, see
Figure 42. If the terminus of the last section
is not within this distance, use the telescopic
vent section SV4.5LA, as the last vent section.
For wall thicknesses greater than that shown in
Figure42,refertoTable8onpage23.Thistable
liststheadditionalventingcomponentsneeded
(in addition to the termination and adapter) for
a particular range of wall thicknesses.
Firestop/Spacer (SV4.5HF) shown
on the exterior side of the wall. It
may also be installed on the
interior side.
SV4.5HT-2
Termination
7"
(178)
10-1/2"
12-1/8"
(267mm)
(308 mm)
5-1/8"
(130 mm)
3"
(76 mm)
1"
Adapter
SV4.5RCH
(25.4 mm)
Note: Centerline of Vent Piping is
NOT the Same as the Centerline of
the Framed Opening.
K. Attach termination adapter - Attach the
adapter(adapter-SV4.5RCH-providedwiththe
termination) to the vent section or telescoping
ventsection),elboworappliancecollarasshown
in Figure 41 in the same manner as any SV4.5
vent component (refer to Step E).
See Figures 13 through 16 on
pages 11 for Min. Distance to
Base of Appliance.
6 to 48 inch Vent Section,
Telescopic vent section,
Elbow or Appliance Collar
Base of Appliance
Installing the Square Horizontal Termination (SV4.5HT-2)
Figure 41
L. Install Firestop/Spacer at exterior wall
-
When using the square termination, install
*Use silicone caulking to seal
the top and sides of the
termination, up to the
underlayment, stucco, or
masonry wall surface.
SV4.5HF (Secure Vent), SF4.5HF (Secure Flex)
Firestop/Spacerovertheopeningattheexterior
sideoftheframing, longsideup, withthe3inch
spacer clearance at the top as shown in Figure
41, and nail into place.
Maximum wall thickness
10 in.(254 mm)**
Interior Surface of
Finished Wall
Exterior Surface of Siding
Exterior Surface of
Framing
Maximum Extent of
Vent Run Sections
Relative to Exterior
Surface of Framing
Siding
*Caulk
(The Firestop/Spacer may also be installed over
the opening at the interior side of the framing.)
6 in. to 9-1/4 in.
(152 to 235 mm)**
Last Vent Section. Use
Telescopic Vent
Section (SV4.5LA), If
Necessary
M. Install the desired termination -
1.Installthesquaretermination(SV4.5HT-2)-
Forthelaststep,fromoutsidetheexteriorwall,
slide the collars of the termination onto the
adapter (the outer over the outer and the inner
inside the inner) until the termination seats
against the exterior wall surface to which it
will be attached. Orient the housing of the
termination with the arrow pointed upwards.
Securetheterminationtotheexteriorwall. The
horizontal termination must not be recessed
into the exterior wall or siding by more than
the 1-1/4" (32 mm) as shown in Figure 42.
SV4.5HT-2
Square Termination
*Caulk
SV4.5HT-2
Square Termination
Adapter
SV4.5RCH
1-1/4" Maximum Recess of
the Square Termination into
Exterior Finishing Material
**For thicknesses greater
than 10 inches, see Table 8.
Stucco
Venting Connection and Exterior Wall Recessing of the
Horizontal Square Termination (SV4.5HT-2).
SVHRK Snorkel Cap –The snorkel cap is de-
signedtobefittedintoabasementwindowbox.
The SVHRK cap is for use with flex vent
Theverticaldistancebetweentheinletandoutlet
of the cap is 28 in. (711 mm). pipe.
Figure 42
Horizontal terminations have been designed to perform in a wide range of weather
conditions. Our terminations meet or exceed industry standards.
When selecting the locations of your horizontal terminations, do not place the termination
where water from eaves and adjoining rooflines may create a heavy flow of cascading water
onto the termination cap. If the cap must be placed where the possibility of cascading water
exists, it is the responsibility of the builder to direct the water away from the termination
cap by using gutters or other means.
IMPORTANT: The vent termination is hot
while in operation and for a period of
time following the use of the fireplace.
To prevent contact with hot surfaces,
we recommend the use of a Termina-
tion Guard. See Page 39. This can be
purchased at your local dealer.
Take care to carefully follow the installation instructions for the termination, including the
use of silicone caulking where required.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
HORIZONTAL VENT FIGURES/TABLES
Table F
Note: Secure Vent components (rigid vent pipe and terminal) are shown
in the figures; Secure Flex components (flexible vent pipe and terminal)
may also be used.
V Minimum
feet (meter)
Elbow Only
(0.305)
H Maximum
feet
(meter)
(0.914)
(1.524)
(3.048)
(4.572)
(6.096)
Note: Two 45 degree elbows may be used in place of one 90 degree
elbow. The same rise to run ratios, as shown in the venting figures for
90 elbows, must be followed if 45 degree elbows are used.
3
5
1
2
3
4
10
15
20
(0.610)
(0.914)
(1.219)
Note: Itisveryimportantthatthehorizontal/inclinedrunbemaintained
in a straight (no dips) and recommended to be in a slightly elevated
plane, in a direction away from the fireplace of 1/4" rise per foot (20
mm per meter) which is ideal, though rise per foot run ratios that are
smaller are acceptable all the way down to at or near level.
V + H = 40 feet (12.2 m) Max.
H = 20 ft. (6.096 m) Max.
Note: SV4.5VF(SecureVent),SF4.5VF(SecureFlex)firestop/spacermust
be used anytime vent pipe passes through a combustible floor or ceiling.
SV4.5HF (Secure Vent), SF4.5HF (Secure Flex) firestop/spacer must be
used anytime vent pipe passes through a combustible wall.
Square termination (SV4.5HT-2)
shown.
H
Venting Components Required for Various Exterior Wall
Thicknesses, when using Typical Termination Kits
V
Vent Components Required Exterior Wall Thickness - inches (mm)
Termination Kit Only
6 to 9-1/4 (152 to 235)
TerminationKitand 6In.Vent
Section (SV4.5L6)
10-3/4 to 14 (273 to 356)
Wall Firestop/Spacer
(SV4.5HF)
v
Termination Kit and 12 in.
Vent Section (SV4.5L12)
16-3/4 to 20 (426 to 508)
Termination Kit and Tele-
scopic Section (SV4.5L12)
See Table 8 as an aid in venting component
selection for a particular range of exterior wall
thicknesses.
11-3/4 to 20 (299 to 508)
Note: See Figure 42 showing wall thickness range
when using SV4.5HT-2 termination kit.
Table 8
Example: If 20 feet of (H) horizontal vent run is needed, then 4 feet
minimum of (V) vertical vent will be required.
This table shows a 1(V) to 5(H) ratio. For every 1 foot of vertical, you are
allowed 5 feet of (H) horizontal run up to a maximum (H) horizontal run
of 20 feet.
uWhen using
Secure Flex, use
Firestop / Spacer
SF4.5HF
H = 28 in. (711 mm)
Maximum
When using Secure Flex, use Firestop / Spacer SF4.5VF
When using Secure Flex, use Firestop / Spacer SF4.5HF
u
v
Square
21 in. (533 mm)
Maximum
termination
(SV4.5HT-2)
shown
Figure 44 - Top Vent, ONE 90 DEGREE ELBOW
7 in. (711 mm)
WARNING
Under no circumstances, may separate sections of
concentric flexible vent pipe be joined together.
u
Wall Firestop / Spacer
(SV4.5HF)
See Table 8 as an aid in venting component selection for a particular range
of exterior wall thicknesses.
Figure 43 - Side Vent, NO ELBOWS
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
HORIZONTAL VENT FIGURES/TABLES (continued)
Table G
V Minimum
H
+H1 Maximum
H Maximum
H
H
1
feet
5
(meter)
(1.524)
(3.048)
(4.572)
(6.096)
feet (meter)
feet
(meter)
(0.305)
(0.610)
(0.914)
(1.219)
2
4
6
8
(0.610)
(1.219)
(1.829)
(2.438)
1
2
3
4
10
15
20
Wall Firestop/
v
Spacer (SV4.5HF)
V + H + H = 40 feet (12.2 m) Max
1
H = 8 feet (2.438 meters) Max.
uCeiling Firestop
/ Spacer (SV4.5VF)
H + H = 20 feet (6.096 meters) Max.
1
Square termination
(SV4.5HT-2) shown
V
When using Secure Flex, use Firestop /
uSpacer SF4.5VF
When using Secure Flex, use Firestop /
vSpacer SF4.5HF
Example: If 20 feet of (H + H1) horizontal vent
runisneeded,then4feetminimumof(V)vertical
vent will be required.
Thistableshowsa1(V)to5(H)ratio. Forevery1
foot of (V) vertical, you are allowed 5 feet of (H+
H1) horizontal run, up to a maximum horizontal
run of 20 feet.
See Table 8 on Page 23 as an aid in venting
component selection for a particular range of
exterior wall thicknesses.
Figure 45 - Side Vent, TWO 90 DEGREE ELBOWS
Wall Firestop/
Table H
v
Spacer (SV4.5HF)
V Minimum
feet (meter)
Elbow Only
H + H Maximum
1
feet
(meter)
(0.914)
(1.524)
(3.048)
(4.572)
(6.096)
H
3
5
1
2
3
4
(0.305)
(0.610)
(0.914)
(1.219)
H
1
10
15
20
V
Square termination
(SV4.5HT-2) shown
V + H + H = 40 feet (12.2 m) Max.
1
Wall Firestop/
v
H + H = 20 ft. (6.096 m) Max.
1
Spacer (SV4.5HF)
Example: If 20 feet of (H + H ) horizontal vent run
is needed, then 4 feet minimu1m of (V) vertical vent
will be required.
When using Secure Flex, use Firestop
u/ Spacer SF4.5VF
uCeiling Firestop
/ Spacer (SV4.5VF)
This table shows a 1(V) to 5(H) ratio. For every 1
foot of (V) vertical, you are allowed 5 feet of (H+
H1) horizontal run, up to a maximum horizontal
run of 20 feet.
When using Secure Flex, use Firestop
v/ Spacer SF4.5HF
SeeTable8onPage23asanaidinventing
componentselectionforaparticularrange
of exterior wall thicknesses.
Anelbowisacceptableas1footofverticalriseexcept
where an elbow is the only vertical component in
the system. See Figure 44.
Figure 46 - Top Vent, TWO 90 DEGREE ELBOWS
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
HORIZONTAL VENT FIGURES/TABLES (continued)
When using Secure Flex, use
uFirestop / Spacer SF4.5VF
Example: If 20 feet total (H+H1+H )
horizontal vent run is needed, then24
feet minimum of (V) vertical vent will
be required.
Wall Firestop / Spacer
(SV4.5HF)
v
When using Secure Flex, use
vFirestop / Spacer SF4.5HF
This table shows a 1(V) to 5(H) ratio.
For every 1 foot of (V) vertical, you
are allowed 5 feet of horizontal run
up to a maximum total (H+H1+H2)
horizontal run of 20 feet.
Note: See Table 8 as an aid in
venting component selection for
a particular range of exterior wall
H
1
thicknesses.
H
2
Table J
V Minimum
H + H + H Maximum
HMaximum
Ceiling Firestop /
u
1
2
Spacer (SV4.5VF)
feet
5
(meter)
(1.524)
(3.048)
(4.572)
(6.096)
feet (meter) feet (meter)
2
4
6
8
(0.610)
(1.219)
(1.829)
(2.438)
1
2
3
4
(0.305)
(0.610)
(0.914)
(1.219)
V
10
15
20
V + H + H + H = 40 feet (12.2 m) Max
1
2
H = 8 feet (2.438 meters) Max.
H + H + H = 20 feet (6.096 meters) Max.
H
1
2
Square termination (SV4.5HT-2) shown
Figure 47 - Side Vent, THREE 90 DEGREE ELBOWS
Table K
Square termination
(SV4.5HT-2) shown.
V Minimum
(meter)
Elbow Only
(0.305)
H + H Maximum
1
feet
5
(meter)
(1.524)
(1.524)
(3.048)
(4.572)
(6.096)
feet
H
1
5
1
2
3
4
Ceiling Firestop /
u
Spacer (SV4.5VF)
10
15
20
(0.610)
(0.914)
(1.219)
H + H = 20 feet (6.096 m) Max.
1
V + V + H + H = 40 ft. (12.192 m) Max.
H
1
1
V
Wall Firestop / Spacer
(SV4.5HF)
v
1
Example: If20feettotal(H+H1)horizontal
ventrunisneeded,then4feetminimumof
(V) vertical vent will be required.
When using Secure Flex,
uuse Firestop / Spacer
This table shows a 1(V) to 5(H) ratio. For
every1footof(V)vertical, youareallowed
5 feet of (H+ H ) horizontal run, up to a
maximum horiz1ontal run of 20 feet.
V
SF4.5VF
When using Secure Flex,
vuse Firestop / Spacer
An elbow is acceptable as 1 foot of verti-
cal rise except where an elbow is the only
vertical component in the system. See
Figure 44.
SF4.5HF
Wall Firestop
v
Note: See Table 8 as an aid
in venting component selec-
tion for a particular range of
exterior wall thicknesses.
/ Spacer (SV4.5HF)
Figure 48 - Top Vent, THREE 90 DEGREE ELBOWS
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
VERTICAL OR HORIZONTAL VENTING USING
SECuRE FlEx KITS AND COMPONENTS
FLEX VENT
NOTE: OUTER PIPE IS PULLED AWAY TO
SHOW THE DETAIL OF THE INNER PIPE
Secure Flex venting kits and components may
be used in any venting application where rigid
Secure Vent (SV4.5) direct vent components
can be used. All restrictions, clearances and
allowances that pertain to the rigid piping apply
to the flexible venting. Secure Flex kits may
notbemodified;also,undernocircumstances
may separate sections of flex pipe be joined
together. Secure Flex kits may be added to
the end of a vent run made up of rigid Secure
Vent (SV4.5) vent sections provided that doing
so does not violate any of the venting length,
height, routing, horizontal to vertical ratio re-
quirementsorclearanceconsiderationsdetailed
in this manual.
SECURING SCREW
(3 PLACES EQUALLY SPACED
JUST BELOW GEAR CLAMP)
Apply ONLY MIL-PAC BLACK HIGH
TEMPERATURE SEALANT (Catalog No.
10K81) to the outside surface of both
collars of the adapter (be especially
careful to fill the grooves of the outer
collar to be covered by the flexible
pipe) and slide flexible pipe over
inner and outer adapter collars.
GEAR
CLAMPS
1-3/4 in. (44 mm)
Flexible Pipe and
Adapter Outer
1-3/4 in. (44 mm)
Flexible Pipe and
Adapter Inner
Collar Overlap
SecureFlexkitscomewithanincludedadapter
that can be fitted to the appliance collar or the
inclined channel end of the last Secure Vent
(SV4.5) vent section in a rigid system in the
exact same fashion as any other Secure Vent
section. Align the dimpled end of the adapter
overthepreviouslyinstalledsectionorappliance
collar, adjusting the radial alignment until the
four locking dimples of the adapter are aligned
with the inlets of the four incline channels of
the last vent section or collar. Push on the
adapter until it fully engages, then twist the
adapter clockwise running the dimples down
and along the incline channels until they seat
at the end of the channels.
Collar Overlap
Adapter
(SV4.5RF)
SECURING SCREW
(3 PLACES EQUALLY SPACED
JUST BELOW GEAR CLAMP)
Attach Adapter to Appliance
Collar, or Secure Vent Sections
Figure 49
Seetheappropriatesectionsandfiguresshown
throughout the venting section for their instal-
lation requirments.
2. ApplyabeadofMill-PacBlack(700°F)high
temperature sealant - Catalog No. 10K81) to
the outer adapter collar; to the grooves of the
collar which extend approximately 1 inch from
the end and to the flat surface, approximately
1-3/8 inches from the end.
3. Pull and extend the outer flexible vent pipe.
4. Slide the outer flex pipe over the adapter
collar. Ensure the flexible vent pipe completely
engages the adapter collar to a distance of 1³⁄₄
inches from the end, and that it is free from
damage or tears.
5. Slide the gear clamp down and tighten it
fully to secure the flexible vent to the adapter
outer collar approximately 3/4 inch from the
end of the flex.
6. Install three screws 120 degrees apart
throughtheflexibleventpipeandintotheadapter
collar just below the gear clamp to provide ad-
ditional security to the connection.
Flexible Vent Section
Attach the flexible vent to the adapter as fol-
lows (see Figure 49):
A. Install the Inner Flex Pipe -
1. Install the small gear clamp loosely around
the inner flexible vent pipe, push it back out
of the way.
2. ApplyabeadofMill-PacBlack(700°F)high
temperature sealant - Catalog No. 10K81) to
the inner adapter collar, approximately 1/2 inch
from the end.
3. Pull and extend the inner flexible vent pipe.
4. Slide the inner flex pipe over the adapter
collar. Ensure the flexible vent pipe completely
engages the adapter collar to a distance of
1-3/4 inches from the end, and that it is free
from damage or tears.
5. Slide the gear clamp down and tighten it
fully to secure the flexible vent to the adapter
inner collar approximately 3/4 inch from the
end of the flex.
5" (127 mm)
Radius Minimum
Figure 50
E. Attach Flex Vent to Termination -
Secure Flex components can be purchased
separately and attached to bulk lengths of
SecureFlexflexibletubingcuttosizeatthejob
site. SecuretheflexibleventtotheSecureFlex
terminations in the same manner (see Figure
49 ) as it was attached to the adapter.
C. Route Flex Vent -
Ensure that the flex vent is properly routed to
provide the required clearance. Do Not allow
the flexible vent to bend in a radius tighter than
5" (127 mm). Refer to Figure 50. Support
horizontal sections of flex with metal straps at
2 foot (0.61 m) intervals.
Note: Secure Flex vent must be attached
to Secure Flex terminations only. DO NOT
substitute Secure Vent terminations or the
Secure Vent adapter for Secure Flex compo-
nents.ThecollarsofSecureFlexterminations
and adapters have a different circumference
than that used with the Secure Vent pipe.
Additionally, Secure Flex components have
an extended length center tube for use in
attaching the flexible vent.
6. Install three screws 120 degrees apart
throughtheflexibleventpipeandintotheadapter
collar just below the gear clamp to provide ad-
ditional security to the connection.
D. Install Firestop/Spacers at ceilings and walls -
When Secure Flex penetrates a wall or ceiling,
a firestop/spacer is required: use the SF4.5 VF
firestop/spacer for ceilings and the SF4.5 HF
firestop/spacer for walls.
B. Install the Outer Flex Pipe -
1. Install the large gear clamp loosely around
the outer flexible vent pipe, push it back out
of the way.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Refer to Section A for millivolt appliances and
Section B for electronic appliances. The gas
valve is set in place and pre-wired at the factory
on both models.
2. Route a 3-wire, 120 VAC, 60 Hz, 1 ph power
supply to the location on appliance where junc-
tion box is to be installed.
Step 5. FIELD WIRING
CAUTION
3. Open the control compartment access
panel.
Ground supply lead must be con-
nected to the wire attached to the
green ground screw located on the
outlet box. See Figures 52 & 53. Fail-
ure to do so will result in a potential
safetyhazard. Theappliancemustbe
electrically grounded in accordance
withlocalcodesor,intheabsenceof
local codes, the National Electrical
Code, ANSI/NFPA 70-latest edition.
(In Canada, the current CSA C22-1
Canadian Electrical Code).
A. Millivolt Wiring (See Figure 51) –
Install Optional Control Switch (OFF/ON wall
switch, wall thermostat or remote control
receiver). Install snap bushing (provided in
Electrical Outlet Kit) into control switch knock-
outinsidepanel(seeFigures17through20and
53). Wire the optional control switch within the
millivoltcontrolcircuit(asshowninFigure 51)
using the 15 feet of 2 conductor wire supplied
(route wires through the snap bushing to the
optional control switch). Mount the optional
controlswitchorwallthermostatinaconvenient
location on a wall near the fireplace.
4. Wireandinstalltheoutletreceptacletojunc-
tion box, then install into the chosen corner of
the control compartment as shown in Figures
51, 52 and 54.
5. After the receptacle/junction box wiring is
complete, install the field-provided metal junc-
tion box cover plate (see Figure 53).
6. Install the snap bushing (provided in kit)
into the selected cabinet knockout opening in
side cabinets (see Figures 17 through 20 and
53). The snap bushing provides protection for
the wires (see note below) passing through
side cabinet going to an optional burner control
switch Wire in the burner control switch to the
low voltage circuit as shown in Figure 54.
CAUTION: Label all wires prior to disconnec-
tionwhenservicingcontrols.Wiringerrorscan
cause improper and dangerous operation.
CAUTION
Donotconnectoptinalcontrolswitch
to 120VAC power supply.
ATTENTION: Au moment de l'entretien des
commandes, étiquetez tous les fils avant de
les débrancher. Des erreurs de cáblage peu-
vent entraîner un fonctionnement inadéquat
et dangereux.
Note: The supplied 15 feet of 2 conductor wire
hasoneendofeachconductorconnectedtothe
gas valve circuit and the other end of each con-
ductor placed loose on top of the appliance.
2. Install the junction box and receptacle outlet
to the left of the valve in the front (for optional
blower kit). See junction box and receptacle
outlet as explained in steps 1-11 for (B) Elec-
tronic Wiring (on this page).
Verify proper operation after servicing.
Important Note: The gas valve OFF/ON switch
is shown in Figure 56 on Page 30. It is integral
with the gas valve and should be set to the
ON position.
S'assurer que l'appareil fonctionne adé-
quatement une fois l'entretien terminé.
B. Electronic Wiring (See Figure 54)
Note: The electronic appliance must be con-
nected to the main 120 VAC power supply.
WIRING DIAGRAM MILLIVOLT GAS VALVES
WARNING
THERMOPILE
APPLIANCE- MOUNTED
ON/OFF SWITCH
1. Locate the Electrical Outlet Kit provided
(packaged in firebox - contents: junction box, 2
screws, receptacle outlet, OFF/ON rocker switch
-for millivolt units only, and a snap bushing).
Electronicmodelsoftheseappli-
ancesareequippedwithathree-
prong (grounding) plug utilized
in connecting the electronic
components to the junction box
in the lower compartment. This
groundingplugprovidesprotec-
tion against shock hazard and
should be plugged directly into
the properly grounded three-
prong receptacle. DO NOT cut
or remove the grounding prong
from the plug.
(OPTIONAL)
TP-TH
TP
TH
GAS VALVE
BK/W(1)
BK/W(1)
Note: The junction box can be installed in any of
the 4 outside corners of the control compartment
(outlet installed in front left corner is shown in
Figure 53 ). If an optional blower is to be installed
place the junction box to the left of the valve in
the front corner.
WALL-MOUNTED ON/OFF SWITCH (OPTIONAL)
THERMOSTAT (OPTIONAL)
WALL MOUNTED CONFIGURATION FOR FAN SWITCH (OPTIONAL)
BK
R
W
GR
FAN
(OPTIONAL)
JUNCTION BOX
Figure 51
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7. CONNECTING GAS LINE
Receptacle, Junction Box
and Cover Plate Installation
Ground Wire
Connection
Make gas line connections. All codes require a
shut-offvalvemountedinthesupplyline. Figure
55 illustrates two methods for connecting the
gas supply. The flex-line method is acceptable
in the U.S., however, Canadian requirements
vary depending on locality. Installation must
be in compliance with local codes. A sediment
trap is recommended in the gas piping within
the home to prevent moisture and debris in the
line from damaging the valve.
Outlet Receptacle
Junction Box
White
(supply)
Bipolar
Terminal
Screw
latching magnet
not shown
Black
(supply)
These appliances are equipped with a gas flex
lineforuse(wherepermitted)inconnectingthe
unit to the gas line. A gas flex line is provided
to aid in attaching the direct vent appliance to
the gas supply. The gas flex line can only be
used where local codes permit. The flex line
is rated for both natural and propane gas. A
manual shut off valve is also provided with
the flex line.
Note: Supply wires may be alternatively con-
nected to the outlet using the screw terminals,
however the black supply wire must be wired to
a terminal that is opposite (across the outlet) the
point where the white supply wire is connected.
Figure 52
View Of Left
Bottom Corner Of Unit
Step 6. WIRING - OPTIONAL FORCED AIR
BLOWER KIT
Field-provided Metal Junction Box
Cover Plate With Screw
The gas control valve is located in the lower
control compartment.
Junction Box
FBK-100, FBK-200 and FBK-250 Kits
(See Figure 54 on page 29 for wiring) -
knock-out (2
Fireplace
Side
places each side)
To access the valve open the lower control
compartment door (see Figure 56) by pushing
in the right top corner of the door. (The door
is hinged at the bottom.) Remove the bottom
compartment door by sliding the hinge pin,
located at the door’s left side, to the right until
it disengages from the left corner post hole.
Pull the door diagonally to the left, away from
the fireplace.
Press snap
bushing into the
knock-out for
control switch
wires.
An electrical receptacle is provided for the
installation of the FBK-100, FBK-200 and FBK-
250 forced air blower kits. Electrical power
must be connected to this receptacle in order
to operate these blowers. Install the blower
kits according to the installation instructions
provided with the kits.
Figure 53
TEST ALL CONNECTIONS FOR GAS LEAKS
(FACTORY AND FIELD):
The lower control compartment door on the
side opposite the valve lifts on and off.
CAUTION
Remove the carton support from
the control compartment before
operating the appliance.
WARNING
Never use an open flame to
check for leaks.
The millivolt control valve has a 3/8"
(10mm) NPT thread inlet port. The electronic
control valve has a 1/2" (13 mm) NPT thread
inletportandisfittedwitha1/2"x3/8"(13mmx
10mm) NPT fitting.
Secure all joints tightly using appropriate
toolsandsealingcompounds(ensurepropane
resistant compounds are used in propane
applications).
All codes require a shut-off valve mounted
in the supply line. The orientation of the
shut-off valve should face the front. Figure
55 illustrates two methods for connecting the
gas supply. A sediment Trap is recommended
to prevent moisture and debris in the gas line
for damaging the valve.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn on gas supply and test for gas leaks, us-
ing a gas leak test solution (also referred to as
bubble leak solution).
Plug blower
into this
Green
White
Black
Ground - Green
Neutral - White
120 VAC - Black
receptacle
Note: using a soapy water solution is an
effective leak test solution but it is not recom-
mended, because the soap residue that is left
on the pipes/fittings can result in corrosion
over time.
Junction Box
Blower
* Wall-mounted
ON/ OFF Blower
Switch or Variable
Speed Control Switch.
Ground
Tab
Broken
Tab Intact
Red
A. Light the appliance (refer to the lighting
instructionslabelinthecontrolcompartment
or in the Care and Operation Instructions
manual).
J-BOX WIRING FOR
WALL SWITCH
BLOWER CONTROL
Green
Ground
Screw
Neutral
Hot
Side of
Side of
Receptacle
Receptacle
View A
B. Brush all joints and connections with the gas
leak test solution to check for leaks. If bubbles
are formed, or gas odor is detected, turn the
gas control knob (off/pilot/on) to the “OFF”
position. Either tighten or refasten the leaking
connection, then retest as described above.
J-Box Wiring when
using unit mounted
relay module.
Relay Module C/W FBK-250 only. Plug blower
into J-Box receptacle for FBK-100 or FBK-200
application. See View A for J-Box wiring.
BK
W
G
Optional Blower
Junction Box
C. Whenthegaslinesaretestedandleakfree,be
*OFF/ON Switch
(Integral with
Gas Valve)
sure to rinse off the leak testing solution.
Pilot Burner
Assembly
Step 8. VERIFYING APPLIANCE OPERA-
TION
Honeywell
Electronic
Gas
Turn on burner and observe the individual
tongues of flame on the burner. Make sure
all ports are open and producing flame evenly
across the burner. If any ports are blocked, or
partially blocked, clean out the ports.
Valve
Igniter
*
Leave the OFF/ON switch, which is
Connector
integral with the gas valve, in the ON
position.
GROUND
Transformer
** Optional Control Switches: Wall
Switch, Wall Thermostat or Remote
Control Receiver.
BL
BL
BL
BK
R
24 V
With gas line installed run initial system
checkoutbeforeclosingupthefrontoftheunit.
Follow the pilot lighting instructions provided
in the Care and Operation Instructions manual.
For piezo igniter location see Figure 56 on
Page 30 (millivolt appliances only).
120 VAC
Primary
Secondary
Notes:
BK
1. If any of the original wire as supplied
must be replaced, use Type AWM 105°C
- 18 gage wire ONLY.
2. 120 VAC, 60 Hz - Less than 3 Amps.
Caution: label all wires prior to
disconnection when servicing controls.
Wiring errors can cause improper and
dangerous operation.
BK = BLACK BL = BLUE
BK
Optional Control Switch
R = RED
G = GREEN
W = WHITE
W
Field Wired
Factory
Note: lighting Instructions are also found on
the literature tag tied to the gas piping next
to the gas valve. To access the tag, open the
lower control compartment door (Figure 56)
by pushing in simultaneously the left and right
top corners of the door. (The door is hinged at
thebottom). Removethebottomcompartment
door by sliding the hinge pin, located at the
door’s left side, to the right until it disengages
from the left corner post hole. Remove the
modesty panel. To remove the modesty panel,
slide the panel forward until it contacts the
cabinet bottom panel, then lift straight up and
tilt forward. Remove the modesty panel care-
fully, so that none of the wires become loose
or disconnected.
Wired
Schematic Representation Only
Electronic Wiring Diagram (Honeywell) Showing Blower Wiring for Optional FBK-100, FBK-200 & FBK-250 Kits
Figure 54
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Gas Flex-Line Connector
Hood Igniter Rod
MILLIVOLT
3/8" NPT x 3/8"
Flare Fitting
Thermocouple
1/2" x 3/8" Flare
Shut-Off Valve
Gas
Valve
3/8" Flex Tubing
3/8" Min
(9 mm)
Pilot
Nozzels
Gas
Stub
1/2" x 3/8"
Reducer
Thermopile
3/8" Nipple
3/8" Union
3/8" Close Nipple
Figure 57
Electronic Appliance Checkout
3/8" Shut-Off Valve
To light the burner, turn ‘ON’ the unit mounted
On/Offswitchortheoptionalremotewallswitch.
Ensure the igniter lights the pilot. The pilot
flame should engulf the flame rod as shown
in Figure 58.
Figure 55 - GAS CONNECTION
When first lighting the appliance, it will take a
few minutes for the line to purge itself of air.
Once purging is complete, the pilot and burner
willlightandoperateasindicatedintheinstruc-
tion manual.
Millivolt Appliance Checkout
The pilot flame should be steady, not lifting
or floating. Flame should be blue in color with
traces of orange at the outer edge.
ELECTRONIC
3/8 To 1/2 Inch
(9 mm to 13 mm)
Proper Flame
Adjustment
Subsequent lighting of the appliance will not
requiresuchpurging.Inspectthepilotflame(re-
move logs, if necessary, handling carefully).
The top 3/8" (10 mm) at the pilot generator
(thermopile) and the top 1/8" minimum (tip)
of the quick drop out thermocouple should be
engulfed in the pilot flame.
Pilot
Nozzle
Ground
Electrode
Theflameshouldproject1"(25mm)beyondthe
hoodatallthreeports (seeFigure57). Replace
logs if removed for pilot inspection.
Flame Rod
Hot Surface
Igniter
To light the burner; turn “ON” the remote wall
switch and rotate the gas valve control knob
counterclockwise to the “ON” position (“ON”
will be at the top side of the valve).
Figure 58
Step 9. INSTALL VERMICULITE, GLOW-
ING EMBERS AND LOGS
Gas Valve
Control
NOTE: Turn off all electricity to the appliance
beforeyouinstallvermiculite,embersandlogs.
DO NOT attempt to install the logs until the ap-
plianceinstallationhasbeencompleted,thegas
lineconnectedandtestedforleaksandtheinitial
burner operation has been checked out.
Hinge Pin
Compartment
Access panel
ON/OFF
Switch
Modesty Panel
Piezo Ignitor
Figure 56
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION STEPS:
REFERENCE
Firebox Accessories / Parts
READ WARNINGS ON THIS PAGE BEFORE PROCEEDING. FOLLOW THE
LOG PLACEMENT INSTRUCTIONS EXACTLY
Cat. No.
88L53
Model No.
Description
FGE
Bag of Glowing Embers
1. Remove the front glass enclosure panel (see Glass Enclosure Panel
Removal and Installation Instructions, Page 34 ).
80L42
FDVS
Bag of Decorative Volcanic Stone
2. Remove the following from firebox; log set, bag of embers and bag
of vermiculite. Handle logs carefully to prevent breakage.
3. Ensure the Grate is properly installed in the firebox with the 4 legs
of the grate fitting into the 4 dimples on the firebox floor.
4. Placement of Glowing Embers -
WARNING
• DO NOT attempt to install the logs until the appli-
ance installation has been completed, the gas line
connected and tested for leaks and the initial burner
operation has been checked out.
• Thesizeandpositionofthelogsetwasengineered
to give the appliance a safe, reliable and attractive
flame pattern. Any attempt to use a different log
set in the fireplace will void the warranty and will
result in incomplete combustion, sooting, and poor
flame quality.
• Logs get very hot and will remain hot up to one
houraftergassupplyisturnedoff. Handleonlywhen
logs arecool. Turnoffallelectricitytotheappliance
beforeyouinstallgrate,volcanicstone,vermiculite,
embers and logs.
Separatethe Embers(rockwool)intopiecesabout thesizeofaquarter
(see Figure 59). Keep the pieces fluffed up, not matted. Distribute
these pieces over the surface of the burner, as shown in Figure 60.
Do not use more than is necessary. Ensure that the main burner ports
remain uncovered by the ember material.
5. Place Lava Rock - Spread lava rock evenly over firebox floor.
6. Install Vermiculite - Place some vermiculite on the firebox floor around
the grate (the entire bag of vermiculite will NOT be used). See Figure 60.
DO NOT PLACE ANY VERMICULITE ON THE BURNER.
Note: This appliance is provided with enough Glowing Embers for several
applications, do not use all that is in a new bag at one time. For best
glowingeffect,replacetheembermaterialannually.ReplacementGlowing
Embers are available (order Catalog Number 88l53).
• This appliance is not designed to burn wood. Any
attempt to do so could cause irreparable damage to
the appliance and prove hazardous to your safety.
• If logs are not installed according to the log
installation instructions, flame impingement and
impropercombustioncouldoccurandresultinsoot
and/or excessive production of carbon monoxide
(CO), a colorless, odorless, toxic gas.
Figure 59
Glowing Embers
Figure 60
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
EDVPF, EDVST, EDVCL AND EDVCR LOG PLACEMENT
Log
Part
Number
6
4
2
Number Description
1
2
3
4
5
6
Log, Corner
55M18
55M19
55M20
55M21
55M22
55M23
Log, Rear/Left
Log, Front/Left
Log, Rear/Right
Log, Front/Center
Log, Center/Top
Catalog Number for the entire log set: 55M04
1
3
5
Log (3) Lays Over Logs
3
1 And 2
STEP 3
1
STEP 1
Place Bottom Hole Of Log (3) On Pin In Log (2). Position
Grooves At The Bottom Of Log (3) Over The Grate.
Position Groove At The
Bottom Of Log (1) Over
The Burner Log Support
Bracket
Position The Groove At The
Bottom Of Log (1) Over The
Grate And Slide It Forward
Against The Grate Here
Position And Slide Log (4)
1
Against The Back Of The Grate
STEP 4
Position Log (2) Over The Grate
Bar And Slide It Against The Back
Of The Grate Here
2
STEP 2
Place Log (4) Over
4
The Flat Spot On
Position Groove At The Bottom Of Log (2)
Over The Grate Here And Slide It Against
The Back Of The Grate
Log (1) Here
Figure 61
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
EDVPF, EDVST, EDVCL AND EDVCR LOG PLACEMENT (CONTINUED)
Log
Part
Number
6
4
Number Description
2
1
2
3
4
5
6
Log, Corner
55M18
55M19
55M20
55M21
55M22
55M23
Log, Rear/Left
Log, Front/Left
Log, Rear/Right
Log, Front/Center
Log, Center/Top
Catalog Number for the entire log set: 55M04
3
1
5
Position The Round End Of Log (6)
Against The Notch Of Log (4) Here.
Two Charred Spots Face The Front
Position Small End Of Log (6)
On The Notch Of Log (3) Here
6
STEP 5
3
4
Rest Log (5) Against
The Grate Here
Grate
Assembly
Position The Groove In The Back
Of Log (3) Against The Grate
Log (5) Sits In Front
Of The Grate
5
Figure 62
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
To access the glass door securing latches,
first open the lower control compartment door
(Figure 63) by pushing in simultaneously the
left and right top corners of the door (the door
is hinged at the bottom).
Step 10. REMOVING AND INSTALLING
THE GLASS DOOR
Step 11. BURNER ADJUSTMENTS
Flame Appearance and sooting
Proper flame appearance is a flame which is
blueatthebaseandbecomesyellowish-orange
in the body of the flame.
WARNING
• Donotattempttosubstitutethe
materialsusedonthesedoors,
or replace cracked or broken
glass.
Remove the bottom compartment door by
sliding the hinge pin, located at the door’s left
side, to the right until it disengages from the
left corner post hole. Pull the door diagonally
to the left, away from the fireplace.
When the appliance is first lit, the entire
flame may be blue and will gradually turn
yellowish-orange during the first 15 minutes
of operation. If the flame remains blue, or if
the flame is orange with evidence of sooting
(black tip), the air shutter opening may need
to be adjusted.
• Handlethisglasswithextreme
care! Glass is susceptible to
damage – Do not scratch or
handleroughlywhilereinstall-
ing the glass door frame.
• The glass door(s) of this appli-
ance must only be replaced as
a complete unit as provided
by the manufacturer. Do not
attempt to replace broken,
crackedorchippedglasssepa-
rately.
Locate the two (2) latches at the top of the
controlcompartmentanddisengagethemfrom
thedoorframebottomvee-flange,pullingdown
on their handles to open them.
If the air shutter opening is closed too far,
sooting may develop. Sooting is indicated by
black puffs developing at the tips of very long
orangeflames. Sootingresultsinblackdeposits
forming on the logs, appliance inside surfaces
and on exterior surfaces adjacent to the vent
termination.
Installing Glass Enclosure Panel
(see Figure 63 )
Retrieve the glass door. Visually inspect the
gasket on the backside of the frame. Gasket
surface must be clean, free of irregularities
and seated firmly.
Sooting is caused by incomplete combustion
in the flames and lack of combustion air enter-
ing the air shutter opening. To achieve a warm
yellowish-orange flame with an orange body
that does not soot, the shutter opening must be
adjusted between these two extremes.
Position the door in front of the firebox opening
with the bottom of the door held away from the
fireplace(Figure63). Hookthetopflangeofthe
door frame over the top of the firebox frame.
• Do not attempt to touch the
frontenclosureglasswithyour
hands while the fireplace is in
use.
Air Shutter Adjustment Guidelines
Let the bottom of the door frame swing gently
intowardsthefireplaceensuringthatthegasket
seats evenly as the door frame draws shut.
Fasten the two latches located underneath the
firebox floor to the door's vee-flange. Close
both the latches securely.
• If there is smoke or soot present, first check
the log set positioning to ensure that the
flames are not impinging on any of the logs.
If the log set is properly positioned and a
sooting condition still exists, then the air
shutter opening should be increased.
WARNING
Do not operate appliance with
theglassfrontremoved,cracked
or broken.
• Themoreoffsetsintheventsystem,thelarger
the air shutter opening will need to be.
Control Compartment Access Panel and Hinge
Top Flange
Glass Door Frame
Front Glass
Enclosure Panel
• An appliance operated with the air shutter
opened too far, may have flames that appear
blue and transparent. These weak, blue and
transparent flames are termed anemic.
• Propane models may exhibit flames which
candle or appear stringy. If this is present
and persists, adjust the air shutter to a more
closed position, then operate the appliance
for a few more minutes to ensure that the
flame normalizes and the flames do not
appear sooty.
AVERTISSEMENT
Ne pas utiliser l'appareil si le
panneau frontal en verre n'est
pas en place, est craqué ou
brisé.
Modesty Panel
Only doors certified with the appliance
shall be used.
Seules des portes certifiées pour cet
appareil doivent être utilisées.
The following chart is provided to aid you in
achieving the correct air shutter adjustment
for your installation.
CAUTION: DO NOT abuse glass door by
striking or slamming shut.
Bottom Vee-flange
Glass Door Frame
Air Shutter Adjustment Guidelines:
Glass Door
Latch
Firebox Floor
Amount of
Primary Air
Flame
Color
Air Shutter
Adjustment
EDVST SHOWN
Removing Glass Enclosure Panel
(see Figure 63 )
If air shutter is
closed too far
Flame will Air shutter
be orange gap should be
increased
Note: Wheninstallingtheglassdoor,ensurethe
spacing on both sides is even and equal.
Remove the top louver assembly or radiant
panel.
Figure 63
If air shutter is
open too far
Flame will Air shutter
be blue gap should be
decreased
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNINGS
• Airshutteradjustmentshould
only be performed by a quali-
fiedprofessionalservicetech-
nician.
• Ensure front glass panel are
in place and sealed during
adjustment.
CAUTIONS
• Soot will be produced if the
airshutterisclosedtoomuch.
Any damage due to sooting,
resulting from improperly
setting the air shutter, is not
covered under the warranty.
• The air shutter door and
nearby appliance surfaces
are hot. Exercise caution to
avoid injury while adjusting
flame appearance.
Glowing Embers (Rockwool)
Figure 64 - Burner Flame Appearance
1. Refer to Figure 64 for proper flame appearance. To adjust the flame, rotate the adjustment rod toward the back or toward the front of the
fireplace (rod located in the lower control area). Position the air shutter to the factory setting as shown in the table in Figure 65.
2. Light appliance (follow lighting procedure on lighting label in control compartment or see the Care and Operation Manual).
3. Allow the burner to operate for at least 15 minutes while observing the flame continuously to ensure that the proper flame appearance has been
achieved. If the following conditions are present, adjust accordingly.
•
•
If flame appears weak or sooty, adjust the air shutter, incrementally, to a more open position until the proper flame appearance is achieved.
If flame remains blue, adjust the air shutter, incrementally, to a more closed position until the proper flame appearance is achieved.
4. Leave the control knob (off/pilot/on) in the ON position and the burner OFF/ON switch OFF (and remote switches, if applicable).
5. When satisfied that the burner flame appearance is normal, re-install the lower control compartment door then proceed to finish the installation.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Shutter
Adjusting
Rod
Combustible
Wall
Framing
This Area Must Remain
Clear of Combustible
Materials
Orifice
3" (76 mm)
Combustible
Finished Wall
Materials
1 in. Min.
(25 mm)
Increase Shutter
Opening In This
Direction
Header
Decrease Shutter
Opening In This
Direction
Top Spacers
Drywall
Bracket/Spacer
Note - Burners are omitted in this view for clarity.
MAIN BURNER
FACTORY SHUTTER SETTING
Natural Gas Propane Gas
Top of Appliance
Louvers
Top of
Door Frame
Models
inches
(mm)
inches
(mm)
Hood must be
installed as shown.
EDVST
EDVPF
EDVCR
EDVCL
Top of Appliance
Radiant panel
Top of Door Frame
1/4"
(6.35)
5/8"
(15.88)
Hood must be
installed as shown.
Adjustment Rod Positions (when viewed from above)
IF OPTIONAL RADIANT
PANELS ARE INSTALLED
Figure 65
Step 12. HOOD INSTALLATION
Figure 66 - FINISHING REQUIREMENTS
Refer to Figure 66. All of these appliances
must have hoods installed prior to operat-
ing.
FINISHING REQUIREMENTS
- Wall Details
Complete finished interior wall. To install the
appliance facing flush with the finished wall,
position framework to accommodate the thick-
ness of the finished wall (Figure 66 )
See Page 5 for
Cold Climate Insulation and
Page 8 for Clearances
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 13. ATTACHING SAFETY-IN-OPERATION WARNINGS
It is the installers responsibility to ensure these warnings are properly affixed during installation. These warning labels are a
critical step in informing consumers of safe operation of this appliance.
ATTACHING SAFETY-IN-OPERATION
WARNINGS
APPOSITION DES MISES EN GARDE RELATIVES
à LA SéCURITé D’UTILISATION
COLOCACIóN DE ADVERTENCIAS DE
SEGURIDAD EN OPERACIóN
Your fireplace has been furnished with safety Votrefoyeraétélivréavecdesétiquettesdesécuritéqui Su chimenea incluye etiquetas de instrucciones
instruction labels that are to be affixed to the doivent être collées à côté des dispositifs de contrôle de seguridad que deben colocarse en el punto de
operationandcontrolpointofthefireplace. Asafety du foyer. Une étiquette de sécurité doit être collée sur operación y control de la chimenea. Se debe colocar
instructionlabelshouldbeaffixedtothewallswitch la plaque de l’interrupteur contrôlant l’allumage du una etiqueta de instrucciones de seguridad en la placa
plate where the fireplace is turned on and off (See foyer (voir Figure A) ou sur le thermostat mural (voir del interruptor de pared desde el cual se enciende y se
Figure A) or wall thermostat (See Figure B) and if Figure B) et, le cas échéant, sur le boîtier de la télé- apaga la chimenea (ver la Figura A) o en el termostato
used on the remote control handheld transmitter commande(FigureC). Lesmisesengardeauraientdû de pared (ver la Figura B)y en el transmisor de control
(Figure C). The warnings should already have been êtrecolléesaumomentdel’installationinitialedufoyer. remoto (Figura C)siseusa.Lasadvertenciasyadeben
put in place when the fireplace initial set-up was Si ce n’est pas le cas, prenez les étiquettes adhésives haberse colocado cuando se completó la instalación
completed. If they are not affixed at these spots, multilingues fournies avec ces instructions et procédez inicial de la chimenea. Si no están colocadas en estos
locatethemulti-lingualadhesivelabelsprovidedwith comme suit:
lugares,encuentrelasetiquetasadhesivasmultilingües
these instructions and proceed as follows:
1. Locate the wall switch or wall thermostat that
controlsthefireplace(verifytheswitchoperates
the fireplace by turning it on and off). Clean the
wall switch plate or wall thermostat thoroughly
to remove any dust and oils. Affix the label to
the surface of the plate of the wall switch that
controls the fireplace (Figure A) or the wall
thermostat (Figure B). Choose the language
primarily spoken in the home.
1. Repérez l’interrupteur ou le thermostat mural proporcionadas con estas instrucciones y prosiga de
qui contrôle le foyer (vérifiez que l’interrupteur la siguiente manera:
contrôle le fonctionnement du foyer en le faisant 1. Identifique el interruptor o el termostato de pared
basculerdeMarcheàArrêt,etvice-versa). Nettoyez
soigneusement la plaque murale de l’interrupteur
ou le thermostat mural pour éliminer la poussière
et les traces de graisse ou d’huile. Collez l’étiquette
sur la surface de la plaque de l’interrupteur mural
qui contrôle le foyer (Figure A) ou du thermostat
mural (Figure B). Choisissez la langue qui est
principalement parlée dans la résidence du
propriétaire.
quecontrolalachimenea(verifiquequeelinterruptor
opera la chimenea encendiéndola y apagándola).
Limpiebienlaplacadelinterruptoroeltermostatode
pared para quitar el polvo y aceite. Pegue la etiqueta
enlasuperficiedelaplacadelinterruptorquecontrola
la chimenea (Figura A) o en el termostato de pared
(Figura B). Seleccione el idioma que más se habla
en la casa.
2. Ifaremotecontrolisusedtocontrolthefireplace,
locate the transmitter and clean it thoroughly
2. Si se usa un control remoto para controlar la
chimenea, encuentre el transmisor y límpielo bien
para quitar el polvo y aceite. Pegue la etiqueta en la
superficie del transmisor (Figura C). Seleccione el
idioma que más se habla en la casa.
to remove any dust and oils. Affix the label to 2. Si une télécommande est utilisée pour contrôler
the surface of handheld transmitter (Figure C).
Choose the language primarily spoken in the
home.
le foyer, nettoyez la soigneusement pour éliminer
la poussière et les traces de graisse ou d’huile.
Collez l’étiquette sur le boîtier de la télécommande
3. If you are unable to locate the labels, please call
LennoxHearthProductsoryournearestLennox
(Figure C). Choisissez la langue qui est principale- 3. Si no puede encontrar las etiquetas, sírvase llamar
ment parlée dans la résidence du propriétaire.
a Lennox Hearth Products o al distribuidor de
Lennox Hearth Products más cercano para recibir
etiquetasdeinstruccionesdeseguridadadicionales
gratuitas.
Hearth Products dealer to receive additional 3. Si vous ne trouvez pas les étiquettes, veuillez
safety instruction labels free of charge.
appeler Lennox Hearth Products ou votre distribu-
teur Lennox Hearth Products local pour recevoir
gratuitement des étiquettes supplémentaires.
Cat. No. H8024 Replacement Label Kit
Juego de etiquetas de repuesto - Nº de cat. H8024
LENNOX HEARTH PRODUCTS
1-800-9-LENNOX
Étiquettes de remplacement, n° cat. H8024
LENNOX HEARTH PRODUCTS
1-800-9-LENNOX
LENNOX HEARTH PRODUCTS
1-800-9-LENNOX
Note: English is red text on clear label. French and
Spanish are white text on black label.
Nota: La etiqueta en inglés es transparente con texto
rojo. Las etiquetas en francés y español son negras
con texto blanco.
Remarque : Le texte anglais est rouge sur un support
transparent. Le texte français et espagnol est blanc
sur un support noir.
SAFETY LABEL
DIAGRAMS
DIAGRAMMES DES éTIQUETTES
DIAGRAMAS DE ETIQUETAS
DE SEGURIDAD
DE SéCURITé
Figure C
Figure B
Figure A
37
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION ACCESSORIES
Listed Secure Vent™ Components
Cat. No.
77L70
77L71
77L72
77L73
77L74
77L75
Model
SV4.5L6
SV4.5L12
SV4.5L24
SV4.5L36
SV4.5L48
SV4.5LA
Description
6 Inch (152 mm)
12 Inch (305 mm)
24 Inch (610 mm)
36 Inch (914 mm)
48 Inch (1219 mm)
Cat. No.
Model
Description
Vent Sections
(Rigid)
H1968
SV4.5HT-2
Horizontal Square Ter-
mination With Firestop /
spacer (H2246) & Adaptor
(74L61)
Telescopic Length Slip Sec-
tion (2" to 7-1/2" rigid)
H2152
SV4.5CGV-1 Vertical Termination Cap,
High Wind
77L76
77L77
SV4.5E45
SV4.5E90
45 Degree Elbow
H4687
H4716
H4717
SV4.5CTS
Chase Top Termina-
tion, Square, Ref. instr.
#750,207M
90 Degree Elbow
SV4.5CTS-B Chase Top Termination,
Square, Black, Ref. instr.
#750,207M
The following flashings come packaged with a storm collar:
SV4.5CTS-TC Chase Top Termination,
77L78
77L79
SV4.5F
Flat Roof Flashing
Square,TerraCotta,Ref.instr.
#750,207M
SV4.5FA
1/12 to 7/12 Adjustable
Flashing
77L80
77L81
SV4.5FB
7/12 to 12/12 Adjustable
Flashing
SV4.5SC6
Storm Collar (6 per box)
H6183
H6184
H2246
SV4.5HF5
SF4.5HF5
Firestop Spacer, 5", rigid
Firestop Spacer, 5", flex
SV4.5HF-10 Firestop / Spacer-Horizon-
tal, rigid (3-1-1 spacing),
10 Pack
H2247
96K92
SV4.5VF-10 Firestop / Spacer-Vertical,
rigid (1-1-1 spacing), 10
Pack
SV4.5SP
Support Plate
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION ACCESSORIES CONTINUED
Listed Secure Vent™ Components
Listed Secure Flex™ Components
Cat. # Model
Cat. #
Model
Description
Description
These termination kits include firestop/spacer, gear clamps and flex adaptor.
17M52
SV4.5HGS-1 Termination Guard,
Square (1 pack) Ref.
(Fits
94L10 &
H1968)
60L10
98K03
H2248
SF-18
SF-12
18 feet (5.49 m) * com-
pressed flex, Ref. instr.
#750,053M
instr. #750,109M
17M53
87L02
SV4.5HGS-12 Termination Guard, Hori-
zontal Square (12 pack)
12 feet (3.66 m) * com-
pressed flex, Ref. instr.
#750,052M
Ref. instr. #750,109M
SV4.5HGS
Termination Guard for
Horizontal Square Termi-
nation (Deluxe) (1 pack)
Ref. instr. #750,055M
(Fits
94L10 &
H1968)
SF4.5HF-10 Firestop / Spacer - Hori-
zontal,flex(3-1-1spacing)
,
10 Pack
H2249
H1969
77L87
SF4.5VF-10 Firestop/Spacer-Vertical ,
H5820
SV4.5HTSK
Termination Shroud
flex (1-1-1 spacing), 10 Pk
(Guard) for Horizontal
Square Termination (1
pack) (ref. instr. #750246M)
SF4.5HT-2
SFKIT12S
Horizontal Square Termina-
(Fits
H1968)
tion for flex (without flex)
Square Term. for flex
(with 12 inch[305mm]*
compressed flex)
H5816
SV4.5-
TWSK10
Through Wall Shield Kit
(used to shield the direct-
vent pipe from blown
insulation)
77L88
77L89
77L90
77L91
56L74
SFKIT18S
SFKIT24S
SFKIT36S
SFKIT48S
SFVT30
Square Term. for flex
(with 18 inch[457mm]*
compressed flex)
750,247M
Ref. instr. #750,247M
Square Term. for flex
(with 24 inch[610mm]*
compressed flex)
H3907
96K93
SV4.5ARSA
SV4.5SU
Attic Insulation Shield w/
adjustable height, 12"-22"
Square Term. for flex
(with 36 inch[914mm]*
compressed flex)
Support Strap
Square Term. for flex (with
48 inch [1219 mm] *
compressed flex)
10K81
89L40
SFMP
Mill-Pac, Black, HighTem-
perature Sealant
S
e
a
l
a
n
t
Vertical Termination for
flex (flat to 6/12) with flex
adaptor, section of rigid
vent, roof support collar
assembly, roof flashing
and storm collar. Ref. instr.
#750,052M
SFMP-12
Mill-Pac, Black, HighTem-
perature Sealant - Bulk
12 pack
99L02
99L03
H1988
SV4.5HRK14 Horizontal Riser Kit, 14",
Ref. instr. #750,146M
SV4.5HRK36 Horizontal Riser Kit, 36",
56L75
SFVT45
Vertical Termination for
flex (6/12 to 12/12) with
flexadaptor,sectionofrigid
vent, roof support collar
assembly, roof flashing
and storm collar. Ref. instr.
#750,052M
Ref. instr. #750,146M
CTSA-33
CTSO-33
CTSO-44
CTSO-46
Chase Top Shroud Kit,
Arch Top 3 X 3 Ft., Ref.
instr. #750,194M
H1985
H1987
H1986
Chase Top Shroud Kit,
Open Top 3 X 3 Ft., Ref.
instr. #750,193M
91L66
91L67
H7748
SFGC4-6
SFGC7-6
H7748
Gear Clamp 4.5 in. (114
mm) for flex (6 pack)
Chase Top Shroud Kit,
Open Top 4 X 4 Ft., Ref.
instr. #750,193M
Gear Clamp 7.5 in. (190.5
mm) for flex (6 pack)
36"Flex ConnectorKit. 36"
offlexwithtwoadaptersfor
matingtworigidsectionsof
vent together.
Chase Top Shroud Kit,
Open Top 4 X 6 Ft., Ref.
instr. #750,193M
*All compressed flex vents can be expanded up to two times.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS CONVERSION KITS
Natural To Propane Gas Conversion Kit
Models No. Unit Type
EDVST
millivolt
EDVPF
Catalog No.
H0568
WARNING
Thisconversionkitshallbeinstalledbyaqualifiedserviceagencyinaccor-
dance with the manufacturer’s instructions and all applicable codes and
requirementsoftheauthorityhavingjurisdiction.Iftheinformationinthese
instructionisnotfollowedexactly,afire,explosionorproductionofcarbon
monoxide may result causing property damage, personal injury or loss of
life.Thequalifiedserviceagencyisresponsiblefortheproperinstallation
of this kit. The installation is not proper and complete until the operation
of the converted appliance is checked as specified in the manufacturer’s
instructionssuppliedwiththekit.Thequalifiedserviceagencyperforming
this installation assumes responsibility for this conversion.
EDVCR
electronic
EDVCL
H0569
Propane to Natural Gas Conversion Kit
Model No.
EDVST
EDVPF
EDVCR
EDVCL
Unit Type
Catalog No.
millivolt
H0567
INSTALLATION INSTRUCTIONS
Step 1. TURN OFF THE GAS SUPPLY TO THE
APPLIANCE and disconnect power supply at the
circuit breaker. Ensure appliance is cold.
AVERTISSEMENT
Cette trousse de conversion doit être installée par un technicien agréé,
selon les instructions du fabricant et selon toutes les exigences et tous les
codes pertinents de l’autorité compétente. Assurez-vous de bien suivre
les instructions dans cette notice pour réduire au minimum le risque
d’incendie,d’explosionoulaproductiondemonoxydedecarbonepouvant
causer des dommages matériels, des blessures ou la mort. Le tecnicien
agrééestresponsabledel’installationdecettetrousse.L’installationn’est
pas adéquate ni complète tant que le bon fonctionnement de l’appareil
convertin’apasétévérifiéselonlesinstructionsdufabricantfourniesavec
la trousse. Le fournisseur de service qualifié ayant réalisé l'installation
assume les responsabilités liées à la conversion.
CAUTION: THE GAS SUPPLY SHALL BE
SHUT OFF PRIOR TO DISCONNECTING THE
ELECTRICAL POWER, BEFORE PROCEED-
ING WITH THE CONVERSION.
ATTENTION: AVANT D’EFFECTUER
LA CONVERSION, COUPEZ D’ABORD
L’ALIMENTATION EN GAZ, ENSUITE, COU-
PEZ L’ALIMENTATION éLECTRIQUE.
a.Openthecontrolcompartmentaccesspanel,
byactuatingthespring-loadedmagneticcatches
securing the panel, gently depressing the outer
top corners of the panel until the catches "pop"
the panel free and allowing it to swing out and
down to open.
In Canada:
THECONVERSIONSHALLBECARRIEDOUTINACCORDANCEWITHTHEREQUIREMENTS
OF THE PROVINCIAL AUTHORITIES HAVING JURISDICTION AND IN ACCORDANCE
WITH THE REQUIREMENTS OF THE CAN/CSA-B149.1 INSTALLATION CODE.
b. Remove the bottom control compartment
access panel by compressing the spring-loaded
hingepinontheleftsideuntilitdisengagesfrom
the left cabinet panel hole. Pull the panel away
from the fireplace.
LA CONVERSION DEVRA êTRE EFFECTUéE CONFORMéMENT AUX RECOMMANDA-
TIONS DES AUTORITéS PROVINCIALES AYANT JURIDICTION ET CONFORMéMENT
AUX EXIGENCES DU CODE D'INSTALLATION CAN/CSA-B149.1.
c. Remove the modesty panel by pulling the
bottom right corner of the modesty panel out
slightlytodisengagethesnap-fitfeature;liftthe
modesty panel by the tab on the panel's right
end, pull the right end of the panel away from
the cabinet and then pull the panel diagonally
out of the left side cabinet panel slots. (In the
above procedure, reverse the words "left" and
"right"forEDVCRmodels).Removethemodesty
panelcarefully,sothatnoneofthewiresbecome
loose or disconnected.
Gas conversion kits are available to adapt your appliance from the use of one type of gas to the
use of another. These kits contain all the necessary components needed to complete the task
including labeling that must be affixed to ensure safe operation.
Kit part numbers are listed here and the following steps detail the conversion procedure. Refer
to the instructions provided with the conversion kit when performing any gas conversion.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
d. Locate the two (2) latches at the top of the
control compartment. To disengage the two
latches from the bottom vee-flange of the glass
enclosure panel, reach for the handles located
towards the back of the latches and pull the
handles down toward the front of the unit. See
Figure 63 on page 34.
Inlet Pressure Test Port
Pressure
Regulator
Manifold
Pressure
Test Port
Remove
These
Components
Slotted
Cap
e. Swing the bottom of the door out and raise
it slightly to lift the top flange of the door frame
away from the appliance.
Spring
Adjusting
Screw
Figure 68
Figure 70
Step 2. Carefully remove the log set. Exercise
care as not to break the log set.
Step 5. Attach manometer to the manifold side
pressure test fitting and verify manifold pres-
sure reads 3.5 inches water column (0.87 kPa)
for natural gas, and 10.0 inches water column
(2.49 kPa) for propane gas.
Exercise extreme care to prevent damage to
or breakage of the ignitor assembly.
Step 3. Referring to Figure 67, remove the
burner.
Remove the screw securing the pilot assembly
to its mounting bracket. Back off the flare nut
at the end of the pilot gas line to free the pilot
assembly from the gas line. Remove the pilot
orifice and replace it with the one provided with
the conversion kit. Reinstall the pilot assembly
by reversing the steps detailed here.
PAN BURNER
Step 6. Refer to Figure 69 and remove the
pilot hood assembly to access the hexed pilot
orifice. Remove and replace the orifice with the
one provided with the kit.
AIR SHUTTER
ADJUSTMENT LEVER
VENTURI TUBE ARM
When reinstalling the ignitor assembly, use
extreme care to prevent damage and break-
age. Do not apply any leverage to the ignitor
assembly while restoring the retainer clip to
its original position.
Pilot
Orifice
Pilot
Assembly
Pilot
Orifice
FIREBOX SUBFLOOR
Ignitor
Assembly
FRONT OF FIREPLACE
Figure 69
Figure 67
Electronic Appliances
Millivolt Appliances
Step 7. Honeywell Electronic Valves - See
Figure 70 and the instructions provided with
the kit. Remove the slotted cap screw, o-ring,
pressure-regulatingadjustingscrewandspring.
Retain all parts for possible later use. Install
new components from the kit. Black cap and
red spring for propane gas units. Silver cap
and stainless steel spring for natural gas units.
Before installing the cap, attach manometer to
themanifoldsidepressuretestfittingandadjust
screwuntilpressurereads3.5incheswatercol-
umn(0.87kPa)fornaturalgas, and10.0inches
water column (2.49 kPa) for propane gas.
Step 4. Refer to Figure 68 and the instruc-
tions provided with the kit. Using a Torx T20,
removeanddiscardthethreepressureregulator
mounting screws. Remove the pressure regu-
lator, spring, poppet, diaphragm and bushing.
Discard all removed components. Ensure
the rubber gasket installed on the back of the
replacement pressure regulator is properly
positioned and install the new pressure regula-
tor using the new screws supplied with the kit.
Tighten screws to 25 In. lb. torque.
Retaining
Clip
Flare Nut
Note: If the ignitor is damaged, a replacement kit
is available, order Catalog No. 87L54.
Figure 71
All Models
Step 8. (Refer to Figure 67 )
A. Remove the orifice from the manifold and
replace it with the one provided in the kit.
The following table shows the orifice sizes
for natural and propane models. Figure 72
illustrates the orifice. Always check and verify
correct orifice size.
SeeFigure71andreplacethepilotorificeasfol-
lows: Removetheignitorassemblyretainerclip,
and carefully remove the ignitor assembly.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Install the burner as shown in Figure 73.
Step9.Reassembletheremainingcomponents
by reversing the procedures outlined in the
preceding steps.
Ensure that the arm of the venturi of the burner
is hooked onto the air shutter adjustment lever
(refertoFigure67onpage41).Theprimaryair
openingcanbeadjustedbyrotatingtheadjust-
mentleverfrombeneaththefireboxfloor.Refer
to Figure 65 on page 36 for the recommended
minimum primary air opening setting.
Figure 72
Use pipe joint compound or Teflon tape on all
pipefittingsbeforeinstalling(ensurepropane
resistant compounds are used in propane ap-
plications, do not use pipe joint compounds
on flare fittings).
BURNER POSITIONING
PAN
BURNER
Step 10. Attach the conversion label provided
in the conversion kit to the rating plate on the
appliance.
Burner Orifice Sizes (all models)
Natural
Propane
Elevation
Gas
Gas
Feet (meters)
drill size (inches)
drill size (inches)
Step 11. Turn on gas supply and test for gas
leaks.
0-4500
(0-1372)
(0.125")
21L81 •
#41 (0.096")
*
*
21L82 •
ALWAYS TEST PRESSURE WITH THE VALVE
REGULATOR CONTROL AT THE HIGHEST
SETTING
* Standard size installed at factory
• Part /Cat. Number
Table 9
PILOT ASSEMBLY
Figure 73
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:THISPAGEINTENTIONALLYLEFTBLANK.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design,
materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2003 Lennox Hearth Products
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
P/N 850018M REV. H 01/2011
Download from Www.Somanuals.com. All Manuals Search And Download.
|