Land Pride Brush Cutter 318 586A User Manual

Rotary CutterBlade Bolt Kit  
All Rotary Cutter Series - Kit Part No. 318-586A  
When you see this symbol, the subsequent  
Manual No. 318-000M  
instructions and warnings are serious - follow  
without exception. Your life and the lives of  
others depend on it!  
!
DANGER!  
!
Always disconnect main driveline from tractor PTO before  
servicing underside of cutter deck. Cutter can be engaged if  
tractor is started resulting in damage to the cutter, bodily injury  
or death.  
IMPORTANT: Before you begin, read these  
instructions and check to be sure all parts and tools  
are accounted for. Please retain these instructions  
for future reference.  
Tools required:  
Safety Glasses  
1 11/16" Socket  
Work Gloves  
10" Socket Extension  
Your Blade Bolt Kit is exclusively designed for your Land  
Pride Rotary Cutter. Please read these installation  
instructions and your Rotary Cutter Operator’s Manual  
thoroughly before beginning. Especially read information  
relating to safety concerns.  
Flat Tip Screwdriver  
Used 1 1/8"-12 Nut  
Torque Wrench  
(450 ft. lbs. Capacity)  
1. Align dishpan blade bolt hole with access hole in  
deck.  
A separate Parts Manual for your Rotary Cutter is  
purchased from your local dealer. Have model and serial  
numbers handy when placing an order.  
2. Place tractor gear selector in park and/or set brakes,  
shut engine off and remove ignition key.  
3. Disconnect main driveline from tractor PTO and  
secure cutter deck in the up position with solid  
supports before servicing underside of cutter.  
A detailed listing of parts for this accessory kit is listed  
below. Use the list as a checklist to inventory parts  
received. Please contact your local Land Pride dealer for  
missing hardware.  
IMPORTANT: Replacement blades should be  
ordered in pairs. Order only genuine Land Pride  
blades. Other blades may not meet specifications.  
Land Pride Blade Bolt Kit No. 318-586A  
Item Qty Pt No  
Description  
IMPORTANT: Both blades should weigh the same  
1
2
2
2
2
5
6
1 802-277C BLADE BOLT 1 1/8-12 x 3 7/16 W/ KEY  
1 312-075D BLADE SPACER 16 GA. (.060")  
1 312-082D BLADE SPACER 18 GA. (.048")  
1 312-089D BLADE SPACER 20 GA. (.036")  
1 312-808D BLADE SPACER 24 GA. (.024")  
1 804-147C WASHER FLAT 1 HARD ASTMF436  
1 803-170C NUT HEX TOP LOCK 1 1/8-12 PLATE  
with not more than 1 1/2 oz. difference.  
IMPORTANT: Refer to your Operator’s Manual or  
deck decal for direction of blade rotation to ensure  
correct blade placement. Cutter blades must be  
installed with cutting edge leading in rotation.  
N/A 1 318-000M MANUAL, BLADE BOLT KIT  
IMPORTANT: Shim (#2) below may or may not be  
required. If blade deflection is less than 3/4" without  
a shim, then the shim is not used. However, a shim  
is required if blade deflection is greater than 3/4".  
3/4" maximum  
blade deflection  
when blade  
bolts are tight  
IMPORTANT: Locknuts can loose their ability to lock  
properly once removed. Therefore, always use a  
used blade nut or plain nut in steps 4 & 5 below and  
then replace used nut with new locknut in step 6.  
4. Start by assembling blades without shim (#2). Insert  
blade bolt (#1) through blade (#3), dish pan (#4) and  
flat washer (#5). Temporarily secure blade with a  
used 1 1/8"-12 nut. Draw nut up snug. Do not  
tighten.  
5. Check blade deflection. If deflection is greater than  
3/4", remove blade bolt and reassemble as before  
except include shim (#2) in the assembly. Select  
shim thickness based on deflection. The greater the  
deflection, the thicker the shim.  
!
WARNING!  
Always secure cutter deck in the up position with solid supports  
before servicing underside of cutter. Never work under  
equipment supported by hydraulic jacks. Hydraulic jacks can  
drop equipment if controls are actuated or if hydraulic lines  
burst. Either situation can drop the cutter instantly even when  
power to the hydraulic system is shut off.  
6. Once blade deflection is correct, replace used nut  
with new locknut (#6) and torque to 450 ft. lbs.  
© Copyright 2005  
Printed  
8/01/06  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1

Laser MP3 Player MP3 A14 User Manual
LG Electronics Computer Monitor 42VS20 User Manual
LST Smoke Alarm FC600 Series User Manual
Magnavox Blu ray Player MBP5210 User Manual
Makita Cordless Saw 5094D User Manual
Master Bilt Refrigerator BHC 27 User Manual
MaxTech Network Card V32bis User Manual
Maytag Clothes Dryer MEDC400VW User Manual
MB QUART Car Speaker RSD 210 User Manual
McIntosh Door WK 2 User Manual