WS-8011UM
433 MHz
Radio Controlled Temperature Clock
Instruction Manual
ꢀꢁ ꢂꢃꢄ ꢅꢄꢆ ꢇꢀꢄꢈꢈꢉꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
INVENTORY OF CONTENTS
1) WS-8011UM
2) TX6U remote temperature transmitter
3) Instruction manual and warranty card.
ADDITIONAL EQUIPMENT (not included)
1) Two fresh 1.5V AA batteries (for the temperature clock).
2) Two fresh 1.5V AA batteries (for the remote temperature transmitter).
3) Three wall-hanging screws.
4) Appropriate screwdriver for screws.
ABOUT WWVB (Radio Controlled Time)
The NIST (National Institute of Standards and Technology—Time and Frequency
Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact
time signal continuously throughout the United States at 60 kHz. The signal can be
received up to 2, 000 miles away through the internal antenna in the temperature clock.
However, due to the nature of the Earth’s Ionosphere, reception is very limited during
daylight hours. The temperature clock will search for a signal every night when
reception is best. The WWVB radio station derives its signal from the NIST Atomic
clock in Boulder, Colorado. A team of atomic physicists is continually measuring every
second, of every day, to an accuracy of ten billionths of a second per day. These
physicists have created an international standard, measuring a second as 9,192,631,770
vibrations of a Cesium-133 atom in a vacuum. For more information about WWVB
QUICK SET-UP GUIDE
Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.
1. Have the indoor station and outdoor remote 3 to 5 apart.
2. Batteries should be out of both units for 10 minutes.
3. Place the batteries into the remote temperature sensor first then into the
temperature clock.
(All remote temperature sensors must be started before the temperature
clock)
4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.
In this time the temperature clock and remote temperature sensor will start to talk to each
other and the temperature clock will show both the indoor temperature and an outdoor
temperature. If the temperature clock does not display both temperatures after the 10
minutes please retry the set up as stated above. After both indoor and outdoor
temperatures are displayed for 10 minutes you can place your remote temperature sensor
outdoors and set your time.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The remote temperature sensor should be placed in a dry, shaded area. The remote
temperature sensor has a range of 80 feet. Any walls that the signal will have to pass
through will reduce distance. An outdoor wall or window will have 20 to 30 feet of
resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus
resistance should not exceed 80 ft. in a straight line.
NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must
be avoided.
To complete the set up of your temperature clock after the 10 minutes have passed please
follow the steps below.
DETAILED SET-UP GUIDE
I) BATTERY INSTALLATION
Note: To avoid start-up problems make sure that the batteries do not spring free.
A) REMOTE TEMPERATURE TRANSMITTER
1) Remove the battery cover. Place your thumb over
the two air-vent slots on the face of the remote
temperature sensor, push down gently, and slide
battery cover down and off.
Battery
Cover
2) Observing the correct polarity, install 2 AA batteries.
The batteries will fit tightly (to avoid start-up
problems make sure that they do not spring free
during installation).
3) Replace the battery cover.
B) TEMPERATURE CLOCK
1) Remove the battery cover,
located on the backside of the
temperature clock and directly
below the function buttons.
2) Observe the correct polarity,
and install 2 AA batteries.
Battery Cover
3) Replace the battery cover.
Battery Compartment
Note: After the batteries have been installed a tone will sound, and all the LCD’s
(Liquid Crystal Display) will briefly light up. The indoor temperature, the date as
“1/ 1”, the weekday as “MON”, and the remote temperature will be displayed
(within three minutes). Also, the time will appear as “-:--” for approximately 1
minute. The WWVB search is automatically initiated, and a tower icon appears and
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio reception
flashes with the
time colon (no
tower icon will
appear if the
WWVB is too
Alarm
WWVB
Outdoor temperature
Dat
Indoor temperature or
seconds display
Weekday or
seconds display
weak
to
be
detected, and the
time display will remain on “-:--”). While the WWVB search is being conducted
various numbers will appear in the time display. Within 10 minutes the temperature
clock will either display the WWVB time, or discontinue the search if the time is not
found. If the search is cancelled “-:--” will appear in the time LCD. The temperature
clock will conduct a WWVB search every hour until the first signal is found. Once
the WWVB time is found, a search is automatically conducted nightly at midnight.
If the signal is found at midnight, the tower icon will remain, if not, another search
will take place every hour (until 6:00 am) until the signal is found successfully. If no
signal is found during this period, the tower icon will not appear and the clock will
search again at 12:00 am the next night.
II) PROGRAM MODE
To enter the Program Mode hold down the “SET” button for 2 seconds, until
“-5EST” flashes in the Date LCD. The Program Mode is laid out in a manner that
allows you to program each function separately, or you can follow the instructions
entirely to program the temperature clock. Complete programming is usually done
for the initial set-up, and will require you to skip step 1 of programming sections C
through H. Press and release the “SNOOZE” button at any time to exit the Program
Mode, or wait approximately 15 seconds for the temperature clock to automatically
return to normal operation.
A) FUNCTION BUTTONS
There are 4 function buttons located on the backside of the temperature clock.
The function buttons are labeled: “SET”, “+”, “ALARM”, and “SNOOZE”.
B) TIME ZONE SETTING
1) Hold down the “SET” button for 2 seconds, the default (factory) setting
“-5EST” will flash in the Date LCD.
2) Press and release the “+” button to select the appropriate time zone. There
-4ATL
Atlantic Time
-5EST
-6CST
Eastern Time (default setting)
Central Time
-7MST
-8PST
Mountain Time
Pacific Time
-9ALA
-10HAW
-11, -12
GMT
Alaskan Time
Hawaiian Time
Next two time zones West of HAW
Greenwich Mean Time
5
-1, -2, -3GMT
Three time zones West of GMT
Download from Www.Somanuals.com. All Manuals Search And Download.
are 13 time zones to choose from:
3) Press and release the “SET” button to confirm the time zone setting, and to
advance to DST (Daylight saving time) setting.
C) DST (DAYLIGHT SAVING TIME) SETTING
Note: The DST default is “On”, meaning that the WWVB will automatically
change the time according to Daylight Saving Time in the spring and fall. For
areas that do not recognize DST changes (Arizona, Hawaii and parts of
Indiana) turn the DST “OFF”.
1) Hold down the “SET” button for 2 seconds (the selected time zone will
flash).
2) Press and release the “SET” button once more until “On” flashes in the time
LCD and “DST” flashes where the Weekday normally appears.
3) Press and release the “+” button to turn the DST off, as will be indicated by
the display of “OFF” in the time LCD.
4) Press and release the “SET” button to confirm the DST setting, and to
advance to select the language for the weekday.
D) LANGUAGE SELECTION FOR THE WEEKDAY
1) Hold down the “SET” button for 2 seconds (the selected time zone will
flash).
2) Press and release the “SET” button 2 times until the default language “US”
flashes in the time LCD.
3) Press and release the “+” button to toggle through and to select the desired
language. There are 3 languages to select from:
US
F
E
English
French
Spanish
4) Press and release the “SET” button to confirm the language setting, and to
advance to manually set the time.
E) TIME SETTING
Note: When the WWVB signal is found, that time will over-ride the manually set
time.
1) Hold down the “SET” button for 2 seconds (the selected time zone will
flash).
2) Press and release the “SET” button 3 times until the hour “12” flashes in
the time LCD.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Press and release the “+” button to select the hour.
Note: when setting the hour, “PM” will appear to the left of the hour display, if
it is AM nothing will be displayed.
4) Press and release the “SET” button to confirm the hour setting, and to shift
to select the minutes.
5) Press and release the “+” button to select the minutes.
6) Press and release the “SET” button to confirm the time setting and to
advance to manually set the calendar.
F) CALENDAR SETTING
Note: When the WWVB signal is found, that date will over-ride the manually set
date.
1) Hold down the “SET” button for 2 seconds (the selected time zone will
flash).
2) Press and release the “SET” button 5 times until the default year “00”
flashes in the date LCD.
3) Press and release the “+” button to select the year.
4) Press and release the “SET” button to confirm the year, and to set the
month.
5) The default month “1” will flash.
6) Press and release the “+” button to select the appropriate month.
7) Press and release the “SET” button to confirm the month and to set the date.
8) The default date “1” will flash.
9) Press and release the “+” button to select the appropriate date.
10) Press and release the “SET” button to confirm the date and to set the
weekday.
11) The default weekday “MON” (depends on selected language) will flash.
12) Press and release the “+” button to select the appropriate weekday.
13) Press and release the “SET” button to confirm the calendar settings and to
advance to select either 12 or 24-hour time display.
G) 12/24-HOUR SETTING
Note: 12-hour uses AM/PM, 24-hour is also known as “military” time.
1) Hold down the “SET” button for 2 seconds (the selected time zone will
flash).
2) Press and release the “SET” button 9 times until the “12” hour time display
flashes in the time LCD.
3) Press and release the “+” button to toggle between 12 and 24 hour time.
4) Press and release the “SET” button to confirm the 12/24-hour time display
and to advance to select either °F or °C.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
H) SELECTING °F OR °C
1) Hold down the “SET” button for 2 seconds (the selected time zone will
flash).
2) Press and release the “SET” button 10 times until the default “°F” flashes in
the time LCD.
3) Press and release the “+” button to toggle between °F and °C.
4) Press and release the “SET” button to confirm the °F or °C selection and
exit the program mode.
III)
FEATURES & OPERATIONS
A) CHANGING DISPLAY MODE (DAY, SECONDS, AND
TEMPERATURE)
There are three possible display modes to view the day, seconds, and
temperature. The month&date/weekday /indoor temperature/remote temperature
is the default.
To change the display:
1) Press and release the “+” button.
2) The display should now show the month&date/weekday/seconds/remote
temperature
3) Press and release the “+” button.
4) The display will now show the month&date/seconds/indoor
temperature/remote temperature.
5) Press and release the “+” button.
6) The display will return to the normal display.
B) THE ALARM
1) SETTING THE ALARM
Note: The duration of the alarm is 85 seconds. After each of the first two 25
second periods, the rate of the alarm increases.
(a) Hold down the “ALARM” button for 5 seconds.
(b) The “TIME” icon to the right of the minutes (in the time LCD) shifts to
“ALARM” and the hour digit of the alarm flashes.
(c) Press and release the “+” button to set the alarm hour.
(d) Press and release the “ALARM” button to confirm the hour and to set
the alarm minutes.
(e) The alarm minutes flash.
(f) Press and release the “+” button to set the alarm minutes.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
(g) Press and release the “ALARM” button to confirm and to exit the alarm
setting mode.
Note: The alarm will be automatically set to sound when exiting the alarm-
setting mode (indicated by the alarm “sound” icon to the right of the time).
2) ACTIVATING/DEACTIVATING THE ALARM
(a) The alarm will be automatically set to sound when exiting the alarm-
setting mode (indicated by the alarm “sound” icon to the right of the
time).
(b) Press and release the “ALARM” button to activate and deactivate the
alarm. The alarm “sound” icon to the right of the time will appear or
disappear, and the alarm time will be displayed briefly before returning
to the normal display mode.
3) ACTIVATING THE SNOOZE FUNCTION
While the alarm is sounding, press and release the “SNOOZE” button to
activate the snooze function.
The alarm “sound” icon and “SNOOZE” icon (to the right of the time) will
flash.
The duration of the snooze function is 10 minutes, then the alarm will
resume.
4) SUSPENDING ALARM
While the alarm is sounding or the SNOOZE is active, press and release the
“ALARM” button to suspend the alarm until the next day.
C) INDOOR TEMPERATURE
The Indoor temperature appears on the right side of the Date LCD. The
temperature is checked every 10 seconds, and updated whenever there is a
change.
D) REMOTE TEMPERATURE
The remote temperature will be shown on the right side of the lower LCD
screen. The temperature clock receives the outdoor temperature (°F or °C) from
the remote temperature sensor, and the temperature appears in the OUTDOOR
LCD. The remote temperature sensor transmits a new temperature to the
weather temperature clock 3 times every 10 minutes.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IV)
MOUNTING
Hanging Holes
Function Buttons
Foldout Table Stands
There are two possible ways to mount the temperature clock:
•
•
use of the foldout table stands
wall mounting
A) FOLDOUT TABLE STANDS
The Foldout table stand legs are located on the
backside, at the lower corners, and on both sides of
the battery cover. The hinges are towards the edges
of the temperature clock and the ends (with no hinge)
need to be folded out towards the edge. Once the
foldout table stands are extended place the
temperature clock in an appropriate location.
B) WALL MOUNTING
1) Using a straightedge, horizontally space at 3-
15/16 of an inch (100.58mm) three screw
positions on a wall.
2) Install three mounting screws (not included) into
a wall within transmission range—leaving
approximately 3/16 of an inch (5mm) extended
from the wall.
3) Place the temperature clock onto the screws, using the hanging holes on the
backside. Gently pull the temperature clock down to lock the screws into
place.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
V) THE REMOTE TEMPERATURE SENSOR
The remote temperature sensor can be mounted in two ways
•
•
with the use of screws
using the adhesive tape
A) MOUNTING WITH SCREWS
1) Remove the mounting bracket from the remote temperature sensor. The
bracket should snap off easily.
2) Place the mounting bracket over the desired location.
3) Through the three screw holes of the bracket, mark the mounting surface
with a pencil.
4) Where marked, start the screw holes into the mounting surface.
5) Screw mounting bracket onto the mounting surface. Ensure that the screws
are flush with the bracket.
6) Snap the remote temperature sensor onto the mounted bracket.
B) MOUNTING WITH ADHESIVE TAPE
1) With a nonabrasive solution, clean and dry the back of the mounting bracket
and the mounting surface to ensure a secure hold. The mounting surface
should be smooth and flat.
2) Remove the protective strip from one side of the tape.
3) Adhere the tape to the designated area on the back of the mounting bracket.
4) Remove the protective strip from the other side of the tape.
5) Position the remote temperature sensor in the desired location, ensuring that
the temperature clock can receive the signal.
VI) MAINTENANCE & CARE
•
•
Extreme temperatures, vibrations, and shock should be avoided to prevent
damage to the units.
Clean displays and units with a soft, damp cloth. Do not use solvents or
scouring agents—they may mark and damage the displays and casings.
Do not submerge in water.
Immediately remove all low powered batteries to avoid leakage and damage.
Replace with new batteries only, and of recommended size.
Opening the casings invalidates the warranty. Do not try to repair the units.
Contact La Crosse Technology for Repairs.
•
•
•
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem:
Solution:
Problem:
Solution:
The LCD is faint.
Replace the batteries.
“OFL” appears in the indoor temperature LCD.
1) Move unit to an area with warmer or cooler surrounding
temperature.
2) Current surrounding temperatures are outside measuring
range.
Problem:
Solution:
No reception of WWVB signal.
1) It may help reception to face the front of the temperature
clock in the general direction of Ft. Collins, Colorado.
2) Wait overnight for signal.
3) Be sure the temperature clock is at least 6 feet from any
electrical devices, i.e. TV sets, computers, or other radio
controlled clocks.
4) Remove batteries for five minutes, reinsert and leave the unit
alone overnight without pressing buttons.
5) If problems persist contact La Crosse Technology.
Hour is incorrect (minute and date are correct).
Be sure correct time zone and daylight saving time are selected.
“--.-” appears in outdoor temperature LCD
1) Check batteries in the remote temperature sensor.
If batteries are replaced in remote temperature sensor the
temperature clock must be re-started.
Problem:
Solution:
Problem:
Solution:
Remove all batteries, and then follow start up procedure.
“OFL” appears in the outdoor temperature LCD
1) Remote temperature is out of range.
Problem:
Solution:
2) Check batteries.
3) Interference from an outside source (cordless telephone, etc.)
4) Contact La Crosse Technology.
Note: For any questions not answered, contact La Crosse Technology with the contact
information found at the end of this instructional manual.
SPECIFICATIONS FOR WS-8011UM
Temperature:
Measuring range:
32°F to 122°F with 0.2°F resolution (indoor)
-21.8°F to 140°F with 0.2°F resolution (outdoor)
(0°C to 50°C with 0.1°C resolution)
Checking intervals:
Every 10 seconds indoor, 3 times in 10 minutes
for remote temperature.
Power source:
Battery type:
Station: 2 x AA, 1.5V (Alkaline)
Transmitter: 2 x AA, 1.5V (Alkaline)
Approximately 12 months
Battery life:
Dimensions (L x W x H):
11.4 x 0.98 x 7.5 in (290 x 25 x 190mm)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
La Crosse Technology provides a 1-year warranty on this temperature clock. Contact
La Crosse Technology immediately upon discovery of any defects covered by this
warranty.
Before sending the temperature clock in for repairs, contact La Crosse Technology. The
temperature clock will be repaired or replaced with the same or similar model.
This warranty does not cover any defects resulting from improper use, unauthorized
repairs, faulty batteries, or the clocks inability to receive a signal due to any source of
interference.
LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL,
CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED
WITH THE OPERATION OR MALFUNCTION OF THIS TEMPERATURE CLOCK.
THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR
PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF
CHILDRENS’ REACH.
This warranty gives you specific legal rights. You may also have other rights specific to
your State. Some States do not allow the exclusion of consequential or incidental
damages; therefore the above exclusion of limitation may not apply to you.
For warranty work, technical support, or information contact:
La Crosse Technology
2809 Losey Blvd. S.
La Crosse, WI 54601
Phone: 608.782.1610
Fax: 608.796.1020
e-mail:
(warranty work)
(information on other products)
web:
13
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC ID: OMO-01RX (receiver)
OMO-01TX (transmitter)
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS:
1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|