LSI Network Card 7202CP User Manual

USER’S

GUIDE

LSI7202CP CompactPCI

Dual Channel

2 Gbit/s Fibre Channel

Host Adapter

F e b r u a r y 2 0 0 2

Version 1.0

DB15-000228-00

Download from Www.Somanuals.com. All Manuals Search And Download.

This document contains proprietary information of LSI Logic Corporation. The

information contained herein is not to be used by or disclosed to third parties

without the express written permission of an ofﬁcer of LSI Logic Corporation.

LSI Logic products are not intended for use in life-support appliances, devices,

or systems. Use of any LSI Logic product in such applications without written

consent of the appropriate LSI Logic ofﬁcer is prohibited.

The host adapter(s) referred to in this User's Guide contain one or more

transceivers that are certiﬁed as Class 1 laser products that conform to the

requirements contained in the US Food and Drug Administration - Center for

Devices and Radiological Health (FDA/CDRH) regulation 21 CFR 1040,

Performance Standards for Light-Emitting Products and 21 CFR 1010,

Performance Standards for Electronic Products: General.

Internationally, these transceivers are certiﬁed as Class 1 laser products that

conform to the requirements contained in the International Electrotechnical

Commission (IEC) standard 825-1 (1993). Class 1 laser products are not

considered to be hazardous based upon current medical knowledge. This class

includes all lasers or laser systems which cannot emit levels of optical radiation

above the exposure limits for the eye under any exposure conditions inherent in

the design of the laser product. The design of the transceivers on this host

adapter is such that access to laser radiation above a Class 1 emission level

during operation, user maintenance, or service conditions is prevented. However,

there may be a laser embedded in the enclosure of the Class 1 laser that is more

hazardous, but harmful radiation cannot escape the intact enclosure. With any

laser, the following precautions should be followed to prevent accidental exposure

to any levels of optical radiation.

CAUTION: Do not look into the transceiver ports, do not view the transceiver

ports with optical instruments, and avoid direct exposure to the beam.

The following certiﬁcation information is permanently afﬁxed to or inscribed on

the transceiver product so as to be legible and readily accessible to view when

the transceiver is fully assembled for use.

•

Laser Manufacturer

Model #

Serial #

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

Document DB15-000228-00, Second Printing (February 2002). This document

describes the LSI Logic LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre

Channel Host Adapter and will remain the ofﬁcial reference source for all

revisions/releases of this product until rescinded by an update.

LSI Logic Corporation reserves the right to make changes to any products herein

at any time without notice. LSI Logic does not assume any responsibility or

liability arising out of the application or use of any product described herein,

except as expressly agreed to in writing by LSI Logic; nor does the purchase or

use of a product from LSI Logic convey a license under any patent rights,

copyrights, trademark rights, or any other of the intellectual property rights of

LSI Logic or third parties.

TRADEMARK ACKNOWLEDGMENT

The LSI Logic logo design and Fusion-MPT are registered trademarks of LSI

Logic Corporation. Solaris and the Solaris logo are trademarks or registered

trademarks of Sun Microsystems, Inc. in the US and other countries and are

used under license. All other brand and product names may be trademarks of

their respective companies.

To receive product literature, visit us at http://www.lsilogic.com.

For a current list of our distributors, sales ofﬁces, and design resource

centers, view our web page located at

http://www.lsilogic.com/contacts/na_salesofﬁces.html

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

This book is the user’s guide for the LSI Logic LSI7202CP CompactPCI

Dual Channel 2 Gbit/s Fibre Channel Host Adapter. It includes

instructions for installing this adapter with regard to cold and hot

installations and provides this adapter’s speciﬁcations.

Audience

This document assumes that you have some familiarity with CompactPCI

computers and related support devices. The people who beneﬁt from this

book are:

•

Engineers and managers who are evaluating or designing the host

adapter board for possible use in a system

End users who are installing the host adapter board into their

computer

Organization

This document has the following sections:

•

Chapter 1, Installing/Extracting the LSI7202CP Host Adapter

Chapter 2, LSI7202CP Host Adapter Characteristics

Chapter 3, BIOS Features

Chapter 4, Solaris Software Requirements

Appendix A, Glossary of Terms and Abbreviations

LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter

Download from Www.Somanuals.com. All Manuals Search And Download.

Conventions Used in This Manual

Notation

Example

Meaning and Use

courier typeface

# cfagdm

Names of commands and the output from the commands

are shown in courier type face and enclosed in a box.

italic underscore

attachment_point

When an underscore appears in an italicized string next

to a command, enter a user-supplied item of the type

called for with no spaces.

Revision Record

Revision Date

Remarks

0.5

0.6

11/01

12/01

First release.

Second Advance printing. Front matter includes laser safety statement.

Added Section 8.

1.0

02/02

Final printing. Converted to LSI Logic format. Changes throughout.

Preface

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Chapter 1

Chapter 2

Chapter 3

Installing/Extracting the LSI7202CP Host Adapter

1.1

Host Adapter Installation

1-1

1-2

1-3

1.1.1

1.1.2

1.1.3

Cold Installation Preparation

Hot Installation Preparation

Installation

1.2

Extracting the LSI7202CP

1.2.1

1.2.2

Cold Environment Extraction

Hot Environment Extraction

LSI7202CP Host Adapter Characteristics

2.1

General Description

2.1.1

2.1.2

2.1.3

Features

Hardware and Software Support

Fibre Channel Cable Assemblies

2.2

Technical Characteristics

2.2.1

2.2.2

Bus Interfaces

Technical Speciﬁcations

BIOS Features

3.1

BIOS Features

3-1

3.1.1

3.1.2

3.1.3

3.1.4

3.1.5

Intel BIOS

Starting the Intel BIOS Conﬁguration Utility

Using the Intel BIOS Conﬁguration Utility

Exiting the Intel BIOS Conﬁguration Utility

Fcode

3-2

3-3

3-5

3-6

3.2

Troubleshooting

3-14

LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter vii

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4

Solaris Software Requirements

4.1

4.2

Device Driver Software Requirements

Verifying the Installation

4-1

4.2.1

nonvolatileMethod 1 –

Using the show-devs Command

Method 2 -

4-2

4.2.2

Using the probe-scsi-all Command

4-3

4-4

4.3

itmpt Device Driver

4.3.1 Installing the itmpt Sun S P A RC Solaris Driver

Appendix A

Glossary of Terms and Abbreviations

Index

Customer Feedback

Figures

Tables

2.1

4.1

4.2

LSI7202CP CompactPCI Host Adapter

pkgadd Procedure

2-3

4-5

4-6

Completing Floppy Disk Installation

2.1

2.2

2.3

4.1

Hardware and Software Requirements

Speciﬁcations

2-2

2-5

Power Requirements

Error Messages

2-5

4-10

viii

Contents

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1

Installing/Extracting the

LSI7202CP Host Adapter

This chapter describes the installation procedures for the LSI7202CP

CompactPCI Dual Channel 2 Gbit/s Fibre Channel host adapter. The

main topics are:

•

Section 1.1, “Host Adapter Installation,” page 1-1

Section 1.2, “Extracting the LSI7202CP,” page 1-3

1.1 Host Adapter Installation

This section provides a general overview of the tasks needed to perform

either a hot or cold installation. For the exact procedures required for

your system, refer to the operating system and system documentation.

1.1.1 Cold Installation Preparation

Before shutting down the operating environment and halting the system,

ensure that all signiﬁcant application activity on the server has stopped.

To prepare the system for a cold installation, follow these steps.

Step 1. Follow the appropriate procedures, as documented in the

system’s service manual, to shut down and halt the system.

Step 2. Refer to the system’s documentation for the complete power

down procedure and location of the power switch.

Step 3. Press the power switch on the system’s status panel to power

down the system.

Step 4. Verify that the system’s power LED is OFF, which indicates that

the system is completely powered off.

After the system has been shut down and powered off, you can

safely install the card.

LSI7202CP Compact PCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter 1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

1.1.2 Hot Installation Preparation

Refer to your system’s hardware user’s manual for complete instructions

regarding hot installation.

1.1.3 Installation

Review your system’s documentation for the complete instructions before

performing the following steps to install the LSI7202CP into your system:

Step 1. Identify the slot number where you want to insert the adapter.

Step 2. Refer to the system’s documentation for instructions on how to

remove the ﬁller panel.

Step 3. Remove the ﬁller panel from the slot you selected.

Step 4. Push on the red release button and open the LSI7202CP card’s

ejection lever before installing the card in the system.

Step 5. Pull back the ejection lever and slide the card into the

CompactPCI slot.

Step 6. Apply even pressure at both corners of the card and push the

card until it is ﬁrmly seated in the slot.

Step 7. Push the ejection lever over the sprocket toward the card and

into the locked position. This locks the card into the slot.

Step 8. Use a Phillips screwdriver to tighten the captive screws inside

the card’s ejection lever.

Step 9. Attach the Fibre Channel cable to either Port 0 or Port 1 of the

LSI7202CP. This completes the hardware installation.

Important: Check your system’s documentation for any additional

actions that may be required to conﬁgure the system soft-

ware for the newly inserted card.

1-2

Installing/Extracting the LSI7202CP Host Adapter

Download from Www.Somanuals.com. All Manuals Search And Download.

1.2 Extracting the LSI7202CP

The LSI7202CP is a component that you can extract from a hot-swap

compliant system without interrupting the operation of the system. You

can also extract the adapter if installing it in a cold environment after you

power down the system.

You must determine whether you want to perform a cold extraction of the

adapter or a hot extraction. In a cold extraction, you must shut down the

system’s operating system and power down the system before extracting

the adapter. In a hot-swap extraction, you may be required to enter

software commands before and after the extraction to detach the adapter

from the system correctly.

Note :

The following procedures provide a general overview of the

tasks needed to prepare for either a hot or cold extraction.

For the speciﬁc procedures required for your system, refer

to the documentation that shipped with your system.

1.2.1 Cold Environment Extraction

Before extracting your adapter, ensure that all signiﬁcant application

activity on the server has stopped. To extract the LSI7202CP, follow

these steps.

Step 1. Refer to the system’s documentation for the complete power

down procedure and location of the power switch.

Step 2. Press the power switch to power down the system.

Step 3. Verify that the system’s power LED is OFF, which indicates that

the system is completely powered off.

Step 4. Extract the LSI7202CP after the system has been shut down

and powered off.

1.2.2 Hot Environment Extraction

Refer to your system’s hardware user’s manual for complete instructions

regarding hot environment extraction.

Extracting the LSI7202CP

1-3

Download from Www.Somanuals.com. All Manuals Search And Download.

1-4

Installing/Extracting the LSI7202CP Host Adapter

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2

LSI7202CP

Host Adapter

Characteristics

This chapter provides instructions for installing and extracting the host

adapter board and includes these topics:

•

Section 2.1, “General Description,” page 2-1

Section 2.2, “Technical Characteristics,” page 2-3

2.1 General Description

The LSI7202CP is a CompactPCI dual channel 2 Gbit/s Fibre Channel

host adapter. The following sections describe the features of and the

hardware and software support for the LSI7202CP.

2.1.1 Features

The LSI7202CP adapter supports these features:

•

Hot-swap CompactPCI/PCI installation and removal

Asynchronous and synchronous transfers

2.1.2 Hardware and Software Support

The LSI7202CP supports most major software operating systems, such

as Sun Solaris (2.6 and higher), Windows Server (NT 4.0, 2000, XP,

.NET), Linux (RedHat, Suse, Caldera, Turbo), NetWare, UnixWare, HP-

™

UX, and OS/2. The LSI7202CP host adapter utilizes the Fusion-MPT

architecture for all major operating systems. Fusion-MPT architecture

offers the unique feature of having a single, binary operating system

driver that supports Fibre Channel devices and other bus architectures.

LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter 2-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Before you use the LSI7202CP, make sure your system meets the

speciﬁc hardware and software requirements as shown in Table 2.1.

Table 2.1

Hardware and Software Requirements

Requirements

Component

For Solaris SPARC hardware environments

Hardware

Any Sun Microsystems computer with an avail-

able CompactPCI slot

Software

Firmware

The Solaris 8 operating environment

OpenBoot PROM, version 2.1 or greater

For Intel IA-32 or IA-64 hardware environments

Hardware

Software

Any Intel compatible

Windows Server (NT 4.0, 2000, XP, .NET)

Linux (RedHat, Suse, Caldera, Turbo)

NetWare, UnixWare, HP-UX, and OS/2

Firmware

Any Intel compatible BIOS system

2.1.3 Fibre Channel Cable Assemblies

You will use one of two types of Fibre Channel cable assemblies based

on your system.

•

LSI7202CP-LC and LSI7202CP-LC6

–

LC optical to LC optical

LC optical to SC optical

•

LSI7202CP-HS and LSI7202CP-HS6

–

HSSDC2 to HSSDC2

HSSDC2 to HSSDC

2-2

LSI7202CP Host Adapter Characteristics

Download from Www.Somanuals.com. All Manuals Search And Download.

2.2 Technical Characteristics

This section provides information about the CompactPCI, PCI, and Fibre

Channel interfaces on the LSI7202CP. It also includes information about

the physical, electrical, and the thermal/atmospheric characteristics of

the LSI7202CP.

Figure 2.1 provides a photo of the LSI7202CP.

Figure 2.1 LSI7202CP CompactPCI Host Adapter

Port 1 LED

Port 0 LED

Port 0 and Port 1

External Fibre

Channel Connectors

Hot-Swap LED

Red Release Button

and Ejection Lever

2.2.1 Bus Interfaces

This section describes the bus interfaces that the LSI7202CP supports.

2.2.1.1 CompactPCI Interface

CompactPCI is an adaptation of the Peripheral Component interconnect

(PCI) Speciﬁcation for industrial and/or embedded applications that

Technical Characteristics

2-3

Download from Www.Somanuals.com. All Manuals Search And Download.

require a more robust mechanical form factor than desktop PCI.

CompactPCI is electrically compatible with the PCI Speciﬁcation,

allowing low cost PCI components to be utilized in a mechanical form

factor suited for more rugged environments. The LSI7202CP fully

supports Hot Swap as deﬁned in the CompactPCI Hot Swap

Speciﬁcation, Revision 1.0.

2.2.1.2 PCI Interface

The PCI functionality for the LSI7202CP is contained within the

LSIFC929 Dual Channel Fibre Channel I/O Controller. This controller

connects directly to the PCI bus and generates timing and protocol in

compliance with PCI speciﬁcations. This interface provides a high-speed,

standard local bus to the processor and memory subsystems in your

computer.

2.2.1.3 Fibre Channel Interface

The Fibre Channel interface for the LSI7202CP is also contained within

the LSIFC929 Dual Channel Fibre Channel I/O Controller. The LSIFC929

controller provides a direct interface to Fibre Channel. This controller

generates timing and protocol in compliance with the Fibre Channel

standard.

2-4

LSI7202CP Host Adapter Characteristics

Download from Www.Somanuals.com. All Manuals Search And Download.

2.2.2 Technical Speciﬁcations

This section contains the technical speciﬁcations for the LSI7202CP.

2.2.2.1 Data Transfer Speciﬁcations

Table 2.2 lists the performance speciﬁcations for the LSI7202CP.

Table 2.2

Speciﬁcations

Feature

Speciﬁcation

cPCI clock

66 MHz max

264 Mbytes/s

cPCI data burst transfer rate

2.2.2.2 Physical Characteristics

The LSI7202CP ﬁts the 3U Eurocard form factor of 160.00 mm x

100.00 mm, as deﬁned in the CompactPCI Speciﬁcation, Revision 3.0.

The component height on the top and bottom of the LSI7202CP follows

Revision 3.0 of the CompactPCI Speciﬁcation, Revision 2.2 of the PCI

Local Bus Speciﬁcation.

2.2.2.3 Electrical Characteristics

Table 2.3 provides the power requirements for the LSI7202CP.

Table 2.3 Power Requirements

Operating Voltage

Power

3.3 V ± 5% Operation

50.0 mW

7.75 W

5.0 V ± 5% Operation

Technical Characteristics

2-5

Download from Www.Somanuals.com. All Manuals Search And Download.

2.2.2.4 Thermal and Atmospheric Characteristics

The following parameters deﬁne the thermal and atmospheric

environment for the LSI7202CP during normal operation:

•

Temperature range: 0 °C to 55 °C (dry bulb)

Relative humidity range: 5% to 90% noncondensing

Maximum dew point temperature: 32 °C

Airﬂow must be sufﬁcient to keep the LSIFC929 heat sink

temperature below 65 °C

The following parameters deﬁne the storage and transit environment for

the LSI7202CP:

•

Temperature range: −40 °C to +105 °C (dry bulb)

Relative humidity range: 5% to 90% noncondensing

2.2.2.5 Electromagnetic Compliance

The design of the LSI7202CP minimizes electromagnetic emissions,

susceptibility to radio frequency energy, and the effects of electrostatic

discharge. The LSI7202CP carries the BSMI, CE mark, FCC Self-

Certiﬁcation log, Canadian Compliance Statement, VCCI, and meets the

requirements of FCC Class A.

2.2.2.6 Safety Characteristics

The LSI7202CP meets or exceeds the requirements of Underwriters

Laboratory (UL) ﬂammability rating 94 V0. The LSI7202CP is also

marked with the supplier’s name or trademark, type, and UL ﬂammability

rating.

2-6

LSI7202CP Host Adapter Characteristics

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3

BIOS Features

This chapter provides information pertaining to Intel BIOS and Solaris

Fcode and includes these topics:

•

Section 3.1, “BIOS Features,” page 3-1

Section 3.2, “Troubleshooting,” page 3-14

3.1 BIOS Features

A BIOS is the ROM code that is loaded by the system to facilitate booting

from Fibre Channel drives. The BIOS also contains an embedded

conﬁguration manager, used to conﬁgure options provided by the

ﬁrmware. The LSI Logic BIOS integrates with a standard system BIOS,

extending the standard disk service routine provided through INT13h.

Two types of BIOS are available for the LSI7202CP:

•

Intel BIOS for Intel-based platforms

Fcode for Solaris SPARC platforms.

Both Intel BIOS and Fcode concurrently reside on the boards.

3.1.1 Intel BIOS

This section provides the features, description, and installation of the

Intel Fibre Channel BIOS.

3.1.1.1 Intel BIOS Features

The LSI Logic FC Intel BIOS features support:

Selection and conﬁguration for up to 256 adapters

•

LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter 3-1

Download from Www.Somanuals.com. All Manuals Search And Download.

•

Boot device selection from any four host adapters

Automatic INT13 drive mapping for Fibre Channel drives

3.1.1.2 BIOS Overview

During the boot time initialization, the Intel BIOS determines if there are

other hard disks, such as an IDE drive, already installed by the system

BIOS. If there are, the Intel BIOS maps any Intel drives it ﬁnds after the

drive(s) already installed. Otherwise, the Intel BIOS installs drives

starting with the system boot drive. In this case, the system boots from

a drive controlled by the Intel BIOS.

3.1.1.3 Intel BIOS Boot Speciﬁcation (BBS)

The Intel BIOS provides support for the BIOS Boot Speciﬁcation (BBS),

which allows you to choose which device to boot from by selecting the

priority.

To use this feature, the system BIOS must also be compatible with the

BBS. If your system supports the BBS, use the system BIOS setup menu

to select the boot and drive order. In the system BIOS setup, the Boot

Connection Devices menu appears with a list of available boot options.

Use that menu to select the device and rearrange the order. Then exit to

continue the boot process.

3.1.2 Starting the Intel BIOS Conﬁguration Utility

The LSI Logic Intel BIOS allows you to change the default conﬁguration

of your host adapters, using the embedded BIOS Conﬁguration Utility.

When the BIOS loads, the following message appears on your monitor:

Press Ctrl-C to start LSI Logic Configuration Utility...

This message remains on your screen for about ﬁve seconds, giving you

time to start the utility. After you press Ctrl-C, the message changes to:

Please wait, invoking LSI Logic Configuration Utility...

After a brief pause, your computer monitor displays the Main menu of the

BIOS Conﬁguration Utility.

3-2

BIOS Features

Download from Www.Somanuals.com. All Manuals Search And Download.

Note:

Not all devices detected by the Conﬁguration Utility can be

controlled by the BIOS. Devices such as tape drives and

scanners require that a device driver speciﬁc to that periph-

eral be loaded. The BIOS Conﬁguration Utility does allow

parameters to be modiﬁed for these devices.

3.1.3 Using the Intel BIOS Conﬁguration Utility

This section provides the menu formats and user inputs available to

inform users about this utility prior to running it. All BIOS Conﬁguration

Utility screens that display various menus are partitioned into ﬁxed areas.

This area provides static general help text information.

3.1.3.1 Main Menu

When you invoke the LSI Logic Intel BIOS Conﬁguration Utility, the Main

menu appears. This screen displays a scrolling list of up to 256 host

adapters in the system and information about each of them.

To select an adapter, use only the arrow keys and enter key. Then, press

Enterto view and modify the selected adapter’s properties (and to gain

access to the attached devices). After selecting an adapter and pressing

Enter, the FC Link bus is scanned and the Adapter Properties screen

appears.

On the Main menu, two selections are the Boot Adapter List and Global

Properties menus.

Boot Adapter List allows selection and ordering of boot adapters. Refer

to Section 3.1.3.5, “Boot Adapter List Menu,” page 3-5 for more detailed

information.

Global Properties allows changes to global scope settings. Refer to

Section 3.1.3.6, “Global Properties Menu,” page 3-5 for more detailed

information.

Only adapters with LSI Logic Control enabled can be accessed.

3.1.3.2 Adapter Properties Menu

The Adapter Properties menu allows you to view and modify adapter

settings. It also provides access to an adapter's device settings. To

BIOS Features

3-3

Download from Www.Somanuals.com. All Manuals Search And Download.

display this menu, select a device under Adapter ﬁeld on the Main menu

and press Enter.

3.1.3.3 Persistent IDs Menu

The Persistent ID screen is used to review the automatic mapping

between a drive WorldWide Name and its assigned logical SCSI bus and

target ID. You can also use this screen to force a drive to a speciﬁc

logical Target ID.

Selecting Add WWN at an unused location clears out the associated

WWN/DID ﬁeld and allows you to enter the ﬁrst 16 characters of the

WWN. Pressing <Enter>afterwards allows the last 16 characters to be

entered. The CU automatically adds any leading zeros if necessary. If

you make an entry by mistake, select Erase on the appropriate line to

remove the entry.

Logical ID selection defaults to be the lowest ID available. This can be

changed by using the <+> or <-> keys to cycle the numbers. The Bus

ﬁeld always defaults to 0 and cannot be changed. It is displayed in the

case where an outside utility reserved a different number.

Next Page and Previous Page options are provided on the persistent ID

screens, through the F2 key, which moves the screen forward or back by

16 entries. However, the CU requires that any modiﬁcations to the

current page be stored before new entries may be viewed or modiﬁed. A

conﬁrmation window pops up asking to store or discard changes if

needed.

3.1.3.4 Device Properties Menu

The Device Properties menu allows you to view and update individual

device settings for an adapter.

Note:

The number of ﬁelds on the menu requires that you scroll

left/right to view all of the information. When accessing this

menu, use the Home/End keys to scroll to columns cur-

rently not displayed. The scroll indicator on the bottom of

the menu shows where the cursor is relative to the ﬁrst and

last columns.

3-4

BIOS Features

Download from Www.Somanuals.com. All Manuals Search And Download.

3.1.3.5 Boot Adapter List Menu

The Boot Adapter List menu speciﬁes the order in which adapters boot

when more than one LSI Logic host adapter is in a system. You can

select up to four of the total adapters in a system as bootable; however,

you can use only one of the four “active” adapters to control a Boot

Volume.

To select this menu:

1. Press F2 while on the Main menu to move the cursor to the menu

area.

2. Move the cursor to Boot Adapter List with the arrow keys.

3. Press Enter.

You can add or delete adapters using this menu. To add an adapter to

the boot list, press the Insert key while on the Boot Adapter List. Use

the arrow keys to select the desired adapter and press Enter to add it

to the end of the Boot Adapter List.

To remove an adapter from the boot list, press the Deletekey while on

the desired adapter in the Boot Adapter List. You can also change the

boot order by using the “+” or “−” keys. For example, place the cursor on

the adapter that you want to change, and use the “+” or “−” key to raise

or lower the boot order.

3.1.3.6 Global Properties Menu

The Global Properties menu allows you to pause if an alert message has

been displayed, to view display boot information, and to set display and

video modes.

3.1.4 Exiting the Intel BIOS Conﬁguration Utility

The Exit menu for the Intel BIOS Conﬁguration Utility is used for all ﬁve

of the menus listed above. However, the available functionality is different

for the Main menu and the four subordinate menus.

BIOS Features

3-5

Download from Www.Somanuals.com. All Manuals Search And Download.

To exit from the Adapter Properties, Device Properties, Boot Adapter List,

or Global Properties menus, use these exit options:

Cancel exit

This option returns you to the previous menu.

Save changes then

exit this menu

This option implements any changes you made on the

previous menu and returns you to the Main menu.

Discard changes

then exit this menu

This option restores the default settings and returns

you to the Main menu.

To exit from the Main menu, use these exit options:

Cancel exit

This returns you to the Main menu.

Exit the Conﬁguration This option exits the conﬁguration and automatically

Utility reboots your system.

Important: If you reboot the system without properly exiting from this

utility, some changes may not take effect.

3.1.5 Fcode

LSI Logic Solaris-capable Fusion-MPT host adapters have Fcode

resident on board, allowing operation under Sun’s openboot console. All

basic functionality is available at openboot, including the ability to display

devices connected to the adapter, and boot devices on the adapter.

3.1.5.1 Fcode Features

The LSI Logic FC Fcode features support for:

•

Solaris Sparc 2.6, 2.7, and Solaris 8 Open Firmware environments

Root Boot device selection from any target device

Standard command line interface, with help query

Conﬁguration options and selection for each host adapter

3.1.5.2 Identifying the Fibre Channel Disks

The probe-scsi-all command is used to identify the Fibre Channel

devices on the Fusion-MPT adapter.

3-6

BIOS Features

Download from Www.Somanuals.com. All Manuals Search And Download.

To show all disks available from the openboot prompt, use the probe-

scsi-allcommand. Note that this command is used whether the disks

are Fibre Channel or SCSI; all disks available on all Fusion-MPT devices

are displayed.

ok probe-scsi-all

/pci@8,600000/SUNW,qlc@4

LiD HA LUN ---Port WWN--- ----Disk description----

1 1 0 2100002037e4d65b SEAGATE ST318304FSUN18G 0726

/pci@8,700000/IntraServer-Ultra160,scsi@3,1

/pci@8,700000/IntraServer-Ultra160,scsi@3

Target 0

Unit 0 Disk IBM DDRS-34560D

DC1B

/pci@8,700000/IntraServer,fc@2

MPT Version 1.00, Firmware Version 1.02.00

Target 0

Unit 0 Disk SEAGATE ST39173FC

WWN 2100002037109d76 Port ID d9

6615

6258

Target 1

Unit 0 Disk SEAGATE ST39173FC

WWN 210000203710565a Port ID 17

Target 2

Unit 0 Disk SEAGATE ST39173FC

WWN 2100002037105212 Port ID 1

Target 3

Unit 0 Disk SEAGATE ST39173FC

WWN 2100002037103da8 Port ID 26

Target 4

Unit 0 Disk SEAGATE ST39173FC

WWN 210000203710324a Port ID 73

/pci@8,700000/scsi@6

Target 6

Unit 0 Removable Read Only device PLEXTOR CD-ROM PX-20TS

If the Fibre Channel devices on your LSI Logic adapter are not identiﬁed

by your system, check the following:

1. Is the Fibre Channel enclosure powered ON?

BIOS Features

3-7

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Does the LED on the adapter indicate LINK? (note that LINK is only

valid after the device is probed)

3. Does the LED on the switch or remote enclosure indicate LINK?

4. Does the LINK-SPEED parameter selected by the adapter match

that of the bus (1G, 2G, or Auto)?

If you do not see disks, the following additional debug information may

help to identify the problem.

3.1.5.3 Verifying Correct Installation

Use this procedure to verify installation of your Fusion-MPT adapter in

the system:

Step 1. Power on the system.

Step 2. When the banner displays, press the Stop-A keys to interrupt

the boot process and stop at the ok prompt.

Step 3. Use the show-devs command to list the system devices. You

should see an output similar to the following:

ok show-devs

/SUNW,UltraSPARC-III@0,0

/virtual-memory

/memory@m0,0

/aliases

/options

/openprom

/chosen

/packages

/upa@8,480000/SUNW,ffb@0,0

...

/pci@8,700000/IntraServer,fc@2

/pci@8,700000/IntraServer,fc@1,1

/pci@8,700000/IntraServer,fc@1

...

/pci@8,700000/IntraServer,fc@2/disk

/pci@8,700000/IntraServer,fc@2/tape

/pci@8,700000/IntraServer,fc@1,1/disk

/pci@8,700000/IntraServer,fc@1,1/tape

/pci@8,700000/IntraServer,fc@1/disk

/pci@8,700000/IntraServer,fc@1/tape

/pci@8,700000/scsi@6,1/tape

/pci@8,700000/scsi@6,1/disk

3-8

BIOS Features

Download from Www.Somanuals.com. All Manuals Search And Download.

• /pci@8,700000/IntraServer,fc@1

identiﬁes the ﬁrst Fibre Channel interface on an LSI Logic LSIFC929-

based adapter

• /pci@8,700000/IntraServer,fc@1,1

identiﬁes the second Fibre Channel interface on an LSI Logic

LSIFC929-based adapter

•

An LSI Logic LSIFC909-based adapter shows only one such Fibre

Channel device

Note:

The above are examples. The output of show-devs may

vary depending on your system and conﬁguration. Use the

corresponding entries on your system, not the ones given

here.

If these devices are not listed, check that the adapter is correctly

installed, and re-seat the adapter if necessary.

3.1.5.4 Adapter-Speciﬁc Settings

In certain circumstances, the advanced user may want to change

settings for an individual adapter or port, without affecting the other

adapters in the system. Speciﬁc examples of such settings are Fibre

Channel bus speed, host adapter ID (SCSI only: Not Applicable to Fibre

Channel), and Interrupt Coalescing.

To select a speciﬁc Fusion-MPT adapter as the current adapter, use the

selectcommand. Selecting a port or adapter will bring the port online,

and will allow you to show or set certain adapter speciﬁc parameters.

You should use caution while issuing the following commands, as certain

commands could render the bus unusable (such as forcing 1 Gbit/s

operation on a 2 Gbit/s Fibre Channel loop).

select – Use the selectopenboot command to select the adapter entry.

This will open the port to bring the port online.

ok select /pci@8,700000/IntraServer,fc@1

.properties – Use .properties to show the adapter properties.

ok .properties

BIOS Features

3-9

Download from Www.Somanuals.com. All Manuals Search And Download.

firmware-version

mpt-version

scsi-initiator-id

1.02.00

1.00

00 00 00 0f

assigned-addresses 81001010 00000000 00000700 00000000 00000100

83001014 00000000 001a0000 00000000 00020000

8300101c 00000000 00190000 00000000 00010000

82001030 00000000 02000000 00000000 00100000

compatible

model

70 63 69 31 33 65 39 2c 36 32 31 00 70 63 69 31

LSI,929

reg

00001000 00000000 00000000 00000000 00000000

01001010 00000000 00000000 00000000 00000100

03001014 00000000 00000000 00000000 00020000

0300101c 00000000 00000000 00000000 00010000

02001030 00000000 00000000 00000000 00100000

1.00.16

version

device_type

name

scsi-2

IntraServer,fc

fcode-rom-offset

66mhz-capable

devsel-speed

class-code

interrupts

latency-timer

cache-line-size

max-latency

min-grant

00000000

00000001

00010000

00000001

00000040

00000010

00000008

0000001e

00000621

subsystem-id

subsystem-vendor-id 000013e9

revision-id

device-id

vendor-id

00000001

00000621

00001000

show-children – While you have the adapter or port selected, to display

the devices currently connected to this adapter, use the show-children

command:

Select the port or adapter shown (use the port name your system

assigns):

ok select /pci@8,700000/IntraServer,fc@1

ok show-children

MPT Version 1.00, Firmware Version 1.02.00

Link is ready, port is online

WWN 100000a0b8040353 Port ID ef

Target 0

Unit 0 Disk SEAGATE ST39173FC

WWN 2100002037109d76 Port ID d9

6615

6258

Target 1

Unit 0 Disk SEAGATE ST39173FC

WWN 210000203710565a Port ID 17

Target 2

Unit 0 Disk SEAGATE ST39173FC

3-10

BIOS Features

Download from Www.Somanuals.com. All Manuals Search And Download.

WWN 2100002037105212 Port ID 1

Target 3

Unit 0 Disk SEAGATE ST39173FC

WWN 2100002037103da8 Port ID 26

6258

Target 4

Unit 0 Disk SEAGATE ST39173FC

WWN 210000203710324a Port ID 73

3.1.5.5 Interrupt Coalescing

Interrupt coalescing allows the ﬁrmware on the Fusion-MPT device to

group I/Os together to minimize the overhead to the host system. This

feature can result in signiﬁcant performance beneﬁts when I/Os are

rapidly coming into the adapter, as is the case while performing small

sequential reads from a disk.

LSI Logic has performed signiﬁcant testing under multiple I/O conditions,

and has determined that the interrupt coalescence values that are

beneﬁcial over a wide range of I/O conditions are a depth of 4, with a

timeout of 160 microseconds. This means that the host is interrupted

only once for four I/Os processed by the chip, unless 160 microseconds

has passed since the host was last interrupted.

Although LSI Logic has determined that these settings are optimal for a

wide variety of situations, your own I/O load may beneﬁt from a deeper

queue or a longer timeout. LSI Logic provides a mechanism to modify

these values and write them to the nonvolatile EEPROM on the adapter.

Select the port or adapter shown (use the port name your system assigns):

ok select /pci@8,700000/IntraServer,fc@1

ok show-interrupt-coalescing

Interrupt coalescing timeout is a0 (160 decimal) microseconds

Interrupt coalescing depth is 4 (4 decimal)

ok set-interrupt-coalescing <- command with no arguments prints help

usage is <timeout><depth> set-interrupt-coalescing

ok 100 8 set-interrupt-coalescing

Interrupt coalescing timeout selected is 100 (256 decimal) microseconds

Interrupt coalescing depth selected is 8 (8 decimal)

BIOS Features

3-11

Download from Www.Somanuals.com. All Manuals Search And Download.

Interrupt coalescing has been set

Change will take effect after system reset

Note: The system must be power cycled for the changes to take

effect. It is not sufficient to execute the reset-allcommand.

3.1.5.6 Set Fibre Channel Link Speed

There are two modes of operation for Fibre Channel, 1 Gbit/s and

2 Gbit/s. It is important to match the speed of the port with the speed of

the loop or fabric to which the port is attached.

LSI Logic has implemented auto-negotiation on the 2 Gbit/s capable

Fusion-MP devices. If you are experiencing difﬁculty with the auto

negotiate algorithm on your fabric or loop, or you wish to manually set or

show the link speed for the adapter, use the following procedure:

Select the port or adapter shown (use the port name your system assigns):

ok select /pci@8,700000/IntraServer,fc@1

ok show-link-speed

Link speed selected is 1 Gbaud

Current link speed is 1 Gbaud

ok set-link-speed <- command with no arguments prints help

usage is <link-speed> set-link-speed

ok a set-link-speed

Link speed selected is autobaud

Link speed has been set

Change will take effect after system power cycle

ok show-link-speed

Link speed selected is autobaud

Current link speed is 1 Gbaud

Note:

The system must be power cycled for the changes to take

effect. It is not sufficient to execute the reset-allcommand.

3-12

BIOS Features

Download from Www.Somanuals.com. All Manuals Search And Download.

3.1.5.7 Persistent Device Naming

Under certain conﬁgurations, such as when the Fibre Channel disk is the

boot device of a system, it may be preferable to lock a target disk to a

unit number. LSI Logic Fcode allows the system administrator to write a

nonvolatile map of IDs to the Fibre Channel controller.

The following is an example of how to map devices in the persistent

device table.

Select the controller you want to modify, as follows:

ok show-disks

a) /pci@1f,0/pci@1/IntraServer,fc@2/disk

b) /pci@1f,0/pci@1/IntraServer,Ultra2-scsi@1/disk

c) /pci@1f,0/pci@1,1/ide@3/cdrom

d) /pci@1f,0/pci@1,1/ide@3/disk

e) /pci@1f,0/pci@1,1/ebus@1/fdthree@14,3203f0

q) NO SELECTION

Enter Selection, q to quit: a

/pci@1f,0/pci@1/IntraServer,fc@2/disk has been selected.

Type ^Y ( Control-Y ) to insert it in the command line.

e.g. ok nvalias mydev ^Y for creating devalias mydev for

/pci@1f,0/pci@1/IntraServer,fc@2/disk

ok select /pci@1f,0/pci@1/IntraServer,fc@2

ok show-children

MPT Firmware Version 1.00

Target 0

Unit 0

Disk SEAGATE ST39173FC 6615

WWN 200000203710c4e8 PortID a3

ok set-persistent <- command with no arguments prints help

usage is <current-target-id> <persistent-target-id> set-persistent

ok 0 0 set-persistent

ok show-persistent

Entry 1 WWN 200000203710c4e8 Target 0

To clear an entry in the persistent device map, use the clear-persistent

command:

BIOS Features

3-13

Download from Www.Somanuals.com. All Manuals Search And Download.

ok 1 clear-persistent

Entry 1 has been cleared

ok show-persistent

Entry 1 has been deleted from the table, and the table is now empty.

3.2 Troubleshooting

The LSI Logic Intel BIOS Conﬁguration Utility is a powerful tool. If, while

using it, you somehow disable all of your controllers, pressing Ctrl-Aor

Ctrl-Eafter memory initialization during reboot allows you to re-enable

and reconﬁgure.

These messages may appear during the boot process:

• Adapter removed from boot order, parameters will be

updated accordingly!appears when an adapter is removed from

the system or relocated behind a PCI bridge. This message is for

information only, and no further user action is required.

• Configuration data invalid, saving default configuration!

appears if none of the information in NonVolatile Random Access

Memory (NVRAM) is valid. This message is for information only, and

can occur when the BIOS is upgraded or when some external event

has rendered the NVRAM temporarily unreadable.

• Found FC Controller not in following Boot Order List, to

Add: Press Ctrl-C to start LSI Logic Configuration

Utility... appears when fewer than four adapters are in the boot

order and adapters exist in the system which are not in the boot

order. This message is for information only, and indicates that more

than four adapters exist in the system. The additional adapters will

not be managed by the Conﬁguration Utility.

3-14

BIOS Features

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4

Solaris Software

Requirements

This chapter provides device driver requirements and methods to verify

the proper installation of the LSI7202C P , a s well as installation

instructions for the itmpt Sun SPARC Solaris driver. The chapter includes

these topics:

•

Section 4.1, “Device Driver Software Requirements,” page 4-1

Section 4.2, “Verifying the Installation,” page 4-1

Section 4.3, “itmpt Device Driver,” page 4-4

4.1 Device Driver Software Requirements

To support the device drivers for the LSI7202CP, you must have the itmpt

driver for your operating system installed.

After they are installed, the boards have device paths similar to this

example:

/pci@8,700000/IntraServer,fc@1

Under these nodes, one instance of the device driver that has device

nodes is evident:

/pci@8,700000/IntraServer,fc@1,1/disk

/pci@8,700000/IntraServer,fc@1,1/tape

4.2 Verifying the Installation

To verify the proper installation of the LSI7202CP before booting the

operating system, follow one of these two methods.

LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter 4-1

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2.1 nonvolatileMethod 1 – Using the show-devs Command

Step 1. Access the ok prompt.

Type the show-devs command:

Step 2. The system displays output similar to this:

ok show-devs

/SUNW,UltraSPARC-III@0,0

/virtual-memory

/memory@m0,0

/aliases

/options

/openprom

/chosen

/packages

/upa@8,480000/SUNW,ffb@0,0

...

/pci@8,700000/IntraServer,fc@2

/pci@8,700000/IntraServer,fc@1,1

/pci@8,700000/IntraServer,fc@1

...

/pci@8,700000/IntraServer,fc@2/disk

/pci@8,700000/IntraServer,fc@2/tape

/pci@8,700000/IntraServer,fc@1,1/disk

/pci@8,700000/IntraServer,fc@1,1/tape

/pci@8,700000/IntraServer,fc@1/disk

/pci@8,700000/IntraServer,fc@1/tape

/pci@8,700000/scsi@6,1/tape

/pci@8,700000/scsi@6,1/disk

• /pci@8,700000/IntraServer,fc@1

identiﬁes the ﬁrst Fibre Channel interface on an LSI Logic LSIFC929-

based adapter.

• /pci@8,700000/IntraServer,fc@1,1

identiﬁes the second Fibre Channel interface on an LSI Logic

LSIFC929-based adapter

Note:

The above are examples. The output of show-devs may

vary depending on your system and conﬁguration. Use the

corresponding entries on your system, not the ones given

here.

4-2

Solaris Software Requirements

Download from Www.Somanuals.com. All Manuals Search And Download.

If these devices are not listed, check that the adapter is correctly

installed, and re-seat the adapter if necessary.

4.2.2 Method 2 - Using the probe-scsi-all Command

Step 1. Access the ok prompt.

Type the probe-scsi-all command:

Step 2. The system then displays output similar to this:

ok probe-scsi-all

/pci@8,600000/SUNW,qlc@4

LiD HA LUN ---Port WWN--- ----Disk description----

1 1 0 2100002037e4d65b SEAGATE ST318304FSUN18G 0726

/pci@8,700000/IntraServer-Ultra160,scsi@3,1

/pci@8,700000/IntraServer-Ultra160,scsi@3

Target 0

Unit 0 Disk IBM DDRS-34560D

DC1B

/pci@8,700000/IntraServer,fc@2

MPT Version 1.00, Firmware Version 1.02.00

Target 0

Unit 0 Disk SEAGATE ST39173FC

WWN 2100002037109d76 Port ID d9

6615

6258

Target 1

Unit 0 Disk SEAGATE ST39173FC

WWN 210000203710565a Port ID 17

Target 2

Unit 0 Disk SEAGATE ST39173FC

WWN 2100002037105212 Port ID 1

Target 3

Unit 0 Disk SEAGATE ST39173FC

WWN 2100002037103da8 Port ID 26

Target 4

Unit 0 Disk SEAGATE ST39173FC

WWN 210000203710324a Port ID 73

/pci@8,700000/scsi@6

Target 6

Unit 0 Removable Read Only device PLEXTOR CD-ROM PX-20TS

Verifying the Installation

4-3

Download from Www.Somanuals.com. All Manuals Search And Download.

If the Fibre Channel disks on your LSI Logic adapter are not identiﬁed

by your system, check the following:

1. Is the Fibre Channel enclosure powered ON?

2. Does the LED on the adapter indicate LINK? (note that LINK is only

valid after the device is probed)

3. Does the LED on the switch or remote enclosure indicate LINK?

4. Does the LINK-SPEED parameter selected by the adapter match

that of the bus (1G, 2G, or Auto)?

If you do not see disks, the following additional debug information may

help to identify the problem.

4.3 itmpt Device Driver

The LSI Logic itmpt driver is designed to Sun Microsystems SCSA

speciﬁcations for device drivers. This driver allows connection of devices

to LSI Logic adapter cards on PCI-based machines. Refer to

Section 4.3.1, “Installing the itmpt Sun SPARC Solaris Driver,” for

information on installing the itmpt device driver.

4.3.1 Installing the itmpt Sun SPARC Solaris Driver

The LSI Logic LSI7202CP uses the itmpt driver for Solaris systems. This

driver is included with your adapter kit. The following sections describe

the procedures to install the itmpt driver on Solaris based systems.

Note:

If you plan to use an LSI Logic adapter for your system

disk, you must use the installation procedure as described

in Section 4.3.1.2, “Network Installation Procedure,” to load

the device driver during installation.

4.3.1.1 Existing System Installation

These instructions provide details on how to install the LSI Logic itmpt

driver to an existing Solaris operating system.

Note:

You must be logged on as root to perform the installation.

4-4

Solaris Software Requirements

Download from Www.Somanuals.com. All Manuals Search And Download.

Floppy Disk Install – If you received the drivers on a ﬂoppy diskette,

follow these steps:

Step 1. Place the diskette in the ﬂoppy drive and execute the volcheck

command to ensure the system sees the ﬂoppy.

Step 2. Execute the pkgadd procedure to add the itmpt driver to the

operating system.

Example: pkgadd -d floppy/floppy0

You will see the display on the screen as shown in Figure 4.1 and

Figure 4.2.

Figure 4.1 pkgadd Procedure

The following packages are available:

1 TImpt LSI Logic/IntraServer FusionMPT(tm)

Fibrechannel/SCSI drivers

(sparc) itmpt kit version 1.1

Select package(s) you wish to process (or 'all' to process

all packages). (default: all) [?,??,q]: 1

Processing package instance <ITImpt> from

</floppy/intraserver>

LSI Logic/IntraServer FusionMPT(tm) Fibrechannel/SCSI

drivers (sparc) itmpt kit version 1.1

IntraServer Technology, Inc / LSI Logic

Using </> as the package base directory.

## Processing package information.

## Processing system information.

2 package pathnames are already properly installed.

## Verifying disk space requirements.

## Checking for conflicts with packages already installed.

## Checking for setuid/setgid programs.

itmpt Device Driver

4-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 4.2 Completing Floppy Disk Installation

This package contains scripts which will be executed with

superuser permission during the process of installing this

package.

Do you want to continue with the installation of <ITImpt>

[y,n,?] y

Installing LSI Logic/IntraServer FusionMPT(tm)

Fibrechannel/SCSI drivers as <ITImpt>

## Installing part 1 of 1.

/kernel/drv/itmpt

/kernel/drv/itmpt.conf

[ verifying class <none> ]

## Executing postinstall script.

installing /kernel/drv/sparcv9/itmpt

Installation of <ITImpt> was successful.

Step 3. The itmpt device driver is now installed. Reboot the machine to

reconﬁgure the system and to recognize the new devices.

Distribution File Install – If you received the drivers in an

itmpt_install.tar.Z ﬁle, follow these steps:

Step 1. Uncompress and untar the itmpt_install.tar.Z ﬁle by typing the

following commands to create a directory named install:

uncompress itmpt_install.tar.Z

tar -xvf itmpt_install.tar

cd install

Step 2. Execute the pkgadd process as described in the previous

section to add the itmpt driver to the operating system:

Note:

If you change the disk drive conﬁguration of your machine,

it may be necessary to issue the command:

touch /reconfigure

and then reboot the system to allow the system to detect

and correctly install your new disks.

4-6

Solaris Software Requirements

Download from Www.Somanuals.com. All Manuals Search And Download.

4.3.1.2 Network Installation Procedure

If you are using your LSI Logic adapter to support your Sparc Solaris

system disk, you must install the Solaris operating system using a

network install. This section describes a complete installation of the

Solaris operating system to a client system using LSI Logic adapters for

the system disk. The method described in this section allows you to

install the LSI Logic itmpt driver onto a network boot kit, making it

available during the Sparc installation process.

If you are simply installing an LSI Logic adapter as an additional storage

adapter in an existing system, use the driver installation procedure

described in the “Distribution File Install” portion of Section 4.3.1.1,

“Existing System Installation.”

Setting up a Boot/Install Server – Refer to the “Preparing to Install

Solaris Software Over the Network,” section of the Solaris Advanced

Installation Guide, available at http://docs.sun.com.

The basic steps to set up a boot and install server are as follows:

Step 1. Insert the Solaris distribution CD in the boot/install server’s CD-

ROM drive.

Step 2. Change your directory to the Tools area on the distribution CD:

cd /cdrom/cdrom0/Solaris_2.8/Tools

Step 3. Use the setup_install_server script to copy the boot and

installation ﬁles to the boot/install server:

./setup_install_server /export/home/install

Installing the itmpt Driver on the Boot/Install Server – After you

have set up the network boot and install server, follow these steps to run

the install.sh script, using the –nparameter to copy the driver kit to

the boot server’s boot ﬁles:

Step 1. Place the diskette in the ﬂoppy drive and execute the volcheck

command to ensure the system sees the ﬂoppy.

Step 2. Change the directory to the root of the ﬂoppy:

cd /floppy/floppy0

Step 3. Execute the install.sh shell script to add the itmpt driver to

the boot installation area:

itmpt Device Driver

4-7

Download from Www.Somanuals.com. All Manuals Search And Download.

./install.sh –n /export/home/install/Solaris_2.8

Notes:

For Solaris 2.7 boot ﬁles, the installation directory is

/export/home/install/Solaris_2.7.

For Solaris 2.6 boot ﬁles, the installation directory is

/export/home/install/Solaris_2.6.

You can safely ignore the message: “major number

maximum based on server, not client.”

Running the install.shscript this way copies and installs the LSI Logic

drivers into the Tools/Boot/ area of the boot ﬁles and allows LSI Logic

adapters to be booted for installation using the bootserver.

Adding Clients to Your Boot/Install Server – For each machine that

boots into the boot/install server, follow these steps to add a client entry

on the boot/install server:

Step 1. Change the directory to the boot/install kit:

cd /export/home/install/Solaris_2.8/Tools

Step 2. Use the add_install_client script to add the client machine

./add_install_client -i ipaddr

-e ethernetid client_name platform_group

Where:

ipaddr

is the tcp/ip address of the client

ethernetid

is the ethernet hardware (mac) address of

the client

client_name

is the client’s system name

platform_group is the client’s vendor deﬁned hardware

group

Example: ./add_install_client -i 192.168.103.124 –e

00:08:26:02:25:34 sunsys sun4u

Note:

You can obtain the platform_group from a machine of the

same type as the target client using the uname –m

command.

Booting the Client Using the itmpt FC Driver – Now you can begin

the installation of the Solaris operating system to the client target

4-8

Solaris Software Requirements

Download from Www.Somanuals.com. All Manuals Search And Download.

machine using the boot and install server. On the client machine, boot

the network install kit you created in the preceding steps as follows:

ok boot net -v

Important: Choose “Manual Reboot” rather than “Auto Reboot” during

the installation of Solaris on the target machine. If you

choose “Auto Reboot”, you will not have the opportunity to

complete the installation of the LSI Logic drivers and your

system will fail to boot.

After the installation is complete and the system is waiting to be manually

rebooted, proceed to a console window and run the following script:

/sbin/itmptinst

This script copies and installs the drivers from the boot server to the

newly created Solaris installation. After this script is run, the LSI Logic

device driver installation is complete and the system can be rebooted.

Notes:

You can safely ignore the message: “major number

maximum based on server, not client.”

Your Sun machine will prompt you to allow power saving

automatic shutdown. You must answer no to this question

if you are using the LSI Logic adapter to support your boot

disk.

If you change the disk drive conﬁguration of your machine,

it may be necessary to issue the command:

touch /reconfigure

and then reboot the system to allow it to detect and cor-

rectly install your new disks.

4.3.1.3 Troubleshooting the itmpt Device Driver

Table 4.1 lists some potential error messages. In the message

descriptions below <n> is replaced by a number that the operating

itmpt Device Driver

4-9

Download from Www.Somanuals.com. All Manuals Search And Download.

system assigns. This number helps to identify the bus that is reporting

the error.

Table 4.1

Error Messages

Explanation

itmpt<n>: This hardware not

supported by this driver.

itmpt has been told to control an MPT device that is made by a

manufacturer other than LSI Logic/IntraServer. This adapter

requires a special driver provided by that manufacturer. Please

contact the manufacturer for assistance.

itmpt<n>: Failed to map device

registers.

itmpt was unable to access the hardware registers necessary

for operation. The operating system did not properly conﬁgure

the PCI device. Make sure your adapter has LSI Logic Fcode,

and that the adapter is working correctly at the SUN Open Boot

PROM (OBP) prompt.

itmpt<n>: Hardware not properly

enabled by system, cmd=xxxxh.

The system has not properly enabled the conﬁguration

resources that itmpt needs in order to use this hardware. The

cmd=xxxxh value must be reported to LSI Logic technical

support.

itmpt<n>: Could not allocate

The driver was unable to allocate memory required to process

memory to read conﬁguration data. the conﬁguration data. This means that the conﬁguration was

not properly determined. To ﬁx this, you may need to manually

conﬁgure the driver using the itmpt.conf ﬁle.

itmpt<n>: Unable to make reset

notiﬁcation callbacks.

The itmpt was unable to notify the target device driver of a bus

reset. The target driver may start to malfunction.

itmpt<n>: ddi_dma_unbind_handle: The operating system failed to respond to the named routine in

failed

a known manner. This is a fatal error that is not recoverable.

Please report this error to technical support.

itmpt<n>: ddi_dma_numwin() failed.

itmpt<n>: ddi_dma_getwin() failed.

–

itmpt<n>: ddi_dma_alloc_handle:

xxh unknown/impossible.

itmpt<n>:

–

ddi_dma_buf_bind_handle:

DDI_DMA_INUSE impossible.

itmpt<n>:

–

ddi_dma_buf_bind_handle: xxh

unknown/impossible.

itmpt<n>: No KeyROM found.

The adapter is not a valid LSI Logic adapter licensed for use

Hardware contains no valid license. with Solaris systems.

4-10

Solaris Software Requirements

Download from Www.Somanuals.com. All Manuals Search And Download.

Table 4.1

Error Messages (Cont.)

Error Messages

Explanation

itmpt<n>: Hi-level interrupts not

supported.

The adapter is in a slot that cannot be used with this driver. Try

moving the adapter to a different PCI slot.

itmpt<n>: Device in a slave-only slot

and is unusable.

–

itmpt<n>: Failed to attach. This

adapter will not be installed.

Because of one of the previous two errors, this adapter could

not be "attached" to the I/O subsystem and is not accessible.

See the previous error message and solve that problem.

itmpt<n>: Unable to obtain soft

state structure.

The driver was unable to initialize a required data structure and

therefore did not load. Please call technical support.

itmpt<n>: Failed to attach interrupt The driver was unable to initialize the interrupt handler as

handler.

required. Call technical support.

itmpt<n>: The adapter is

The driver is not able to communicate with the hardware. You

malfunctioning or is of an unknown may need to update your driver or your hardware.

type.

itmpt<n>: The adapter is

malfunctioning.

–

itmpt<n>: Failed to create minor

node required for DMI interface.

The driver was unable to create an entry point for the DMI

device driver. If you are not using the DMI device driver, then

you may safely ignore this message.

itmpt<n>: Could not attach to the

SCSI subsystem.

The driver was unable to communicate with the SCSI/FC device

driver that is part of the operating system. You may need to

update your driver.

itmpt<n>: Failed to allocate

memory.

The driver was unable to allocate the memory needed during

initialization. You may have run out of available memory.

itmpt<n>: Unbind failed!

The driver had a problem when attempting to unload itself.

This is a fatal error.

itmpt Device Driver

4-11

Download from Www.Somanuals.com. All Manuals Search And Download.

4-12

Solaris Software Requirements

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix A

Glossary of Terms and

Abbreviations

8B/10B

ANSI

A data encoding scheme developed by IBM, translating byte wide data

to an encoded 10-bit format.

American National Standards Institute, the coordinating organization for

voluntary standards in the United States.

Arbitrated Loop

Topology

A FC Topology that provides a low cost solution to attach multiple ports

in a loop without hubs and switches.

(FC-AL)

BER

Bit

Bit Error Rate.

A binary digit. The smallest unit of information a computer uses. The

value of a bit (0 or 1) represents a two-way choice, such as on or off,

true or false, and so on.

Broadcast

Bus

Sending a transmission to all N_Ports on a fabric.

A collection of unbroken signal lines across which information is

transmitted from one part of a computer system to another. Connections

to the bus are made using taps on the lines.

Bus Mastering

A high-performance way to transfer data. The host adapter controls the

transfer of data directly to and from system memory without bothering

the computer’s microprocessor. This is the fastest way for multitasking

operating systems to transfer data.

Byte

A unit of information consisting of eight bits.

Channel

A point-to-point link, the main task of which is to transport data from one

point to another.

LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter A-1

Download from Www.Somanuals.com. All Manuals Search And Download.

3.75 pc

10.25 pc

11.25 pc

38.25 pc

34.5 pc

4.333 pc

Conﬁguration

Refers to the way a computer is setup; the combined hardware

components (computer, monitor, keyboard, and peripheral devices) that

make up a computer system; or the software settings that allow the

hardware components to communicate with each other.

CPU

Central Processing Unit. The “brain” of the computer that performs the

actual computations. The term Microprocessor Unit (MPU) is also used.

Crosspoint-

Switched

Topology

(FC-XS)

Highest performance FC fabric, providing a choice of multiple path

routings between pairs of F_Ports.

DMA

Direct Memory Access. A method of moving data from a storage device

directly to RAM, without using the CPU’s resources.

DMA Bus

Master

A feature that allows a peripheral to control the ﬂow of data to and from

system memory by blocks, as opposed to PIO (Programmed I/O) where

the processor is in control and the ﬂow is by byte.

Device Driver

EEPROM

EISA

A program that allows a microprocessor (through the operating system)

to direct the operation of a peripheral device.

44.25 pc

Electronically Erasable Programmable Read Only Memory. A memory

chip typically used to store conﬁguration information.

Extended Industry Standard Architecture. An extension of the 16-bit ISA

bus standard. It allows devices to perform 32-bit data transfers.

Exchange

Fabric

A term that refers to one of the FC “building blocks”, composed of one

or more nonconcurrent sequences for a single operation.

FC deﬁned interconnection methodology that handles routing in FC

networks.

FC-EP

The future FC Enhanced Physical standard, which will build on and is

compatible with FC-PH.

FC-PH

FC Physical standard, consisting of the three lower levels;

FC-0, FC-1, and FC-2.

FC-0

Lowest level of the FC Physical standard, covering the physical

characteristics of the interface and media.

48.583 p

52.5 pc

A-2

Glossary of Terms and Abbreviations

Download from Www.Somanuals.com. All Manuals Search And Download.

3.75 pc

10.25 pc

11.25 pc

38.25 pc

34.5 pc

4.333 pc

FC-1

FC-2

FC-3

FC-4

Middle level of the FC-PH standard, deﬁning the 8B/10B

encoding/decoding and transmission protocol.

Highest level of FC-PH, deﬁning the rules for signaling protocol and

describing transfer of the frame, sequence, and exchanges.

The hierarchical level in the FC standard that provides common services,

such as striping deﬁnition.

The hierarchical level in the FC standard that speciﬁes the mapping of

Upper Layer Protocols (ULPs) to levels below.

FCC

FCP

FDDI

Federal Communications Commission.

Fibre Channel Protocol.

Fiber Distributed Data Interface. ANSI option for a Metropolitan Area

Network (MAN); a network based on the use of optical ﬁber cable to

transmit data at 100 Mbits/s.

Fibre Channel

Service

The common FC-4 level protocol for all services, transparent to the fabric

type or topology.

Protocol (FSP)

44.25 pc

File

A named collection of information stored on a disk.

Firmware

Software that is permanently stored in ROM. Therefore, it can be

accessed during boot time.

F_Port

“Fabric” port, the access point of the fabric for physically connecting the

user’s N_Port.

FL_Port

Frame

An F_Port that contains arbitrated loop functions.

A linear set of transmitted bits that deﬁne a basic transport element.

Hard Disk

A disk made of metal and permanently sealed into a drive cartridge. A

hard disk can store very large amounts of information.

HAL

Hardware Abstraction Layer.

HIPPI

High Performance Parallel Interface, an 800 Mbits/s interface to

supercomputer networks (formerly known as high speed channel)

developed by ANSI.

48.583 p

52.5 pc

A-3

Download from Www.Somanuals.com. All Manuals Search And Download.

3.75 pc

10.25 pc

11.25 pc

38.25 pc

34.5 pc

4.333 pc

Host

The computer system in which a SCSI host adapter is installed. It uses

the SCSI host adapter to transfer information to and from devices

attached to the SCSI bus.

Host Adapter

A circuit board or integrated circuit that provides a SCSI bus connection

to the computer system.

Internet Protocol.

IPI

ISA

Intelligent Peripheral Interface.

Industry Standard Architecture. A type of computer bus used in most

PCs. It allows devices to send and receive data up to 16 bits at a time.

Kbyte

LCT

Kilobyte. A measure of computer storage equal to 1024 bytes.

Logical Conﬁguration Table.

LLC

Logical Link Control.

Local Bus

A way to connect peripherals directly to computer memory. It bypasses

the slower ISA and EISA buses. PCI is a local bus standard.

44.25 pc

L_Port

A FC port which supports the arbitrated loop topology.

Link_Control_

Facility

A termination card that handles the logical and physical control of the FC

link for each mode of use.

LUN

Entity within the FC fabric that receives and responds to login requests.

Logical Unit Number. An identiﬁer, zero to seven, for a logical unit.

Megabyte. A measure of computer storage equal to 1024 kilobytes.

Message Frame Address.

Mbyte

MFA

Multicast

NIC

Refers to delivering a single transmission to multiple destination N_Ports.

Network Interface Card.

N_Port

NL_Port

“Node” port, a FC deﬁned hardware entity at the node end of a link.

An N_Port that contains arbitrated loop functions.

48.583 p

52.5 pc

A-4

Glossary of Terms and Abbreviations

Download from Www.Somanuals.com. All Manuals Search And Download.

3.75 pc

10.25 pc

11.25 pc

38.25 pc

34.5 pc

4.333 pc

Operating

System

A program that organizes the internal activities of the computer and its

peripheral devices. An operating system performs basic tasks such as

moving data to and from devices, and managing information in memory.

It also provides the user interface.

Operation

A term, deﬁned in FC-2, that refers to one of the FC “building blocks”

composed of one or more, possibly concurrent, exchanges.

Ordered Set

A FC term referring to four 10-bit characters (a combination of data and

special characters) that provide low level link functions, such as frame

demarcation and signaling between two ends of a link. It provides for

initialization of the link after power-on and for some basic recovery

actions.

Originator

A FC term referring to the initiating device.

Parity Checking A way to verify the accuracy of data transmitted over the SCSI bus. One

bit in the transfer is used to make the sum of all the 1 bits either odd or

even (for odd or even parity). If the sum is not correct, an error message

appears.

PCI

Peripheral Component Interconnect. A local bus speciﬁcation that allows

connection of peripherals directly to computer memory. It bypasses the

slower ISA and EISA buses.

44.25 pc

PDB

PIO

Packet Descriptor Block.

Programmed Input/Output. A way the CPU can transfer data to and from

memory using the computer’s I/O ports. PIO is usually faster than DMA,

but requires CPU time.

Port

The hardware entity within a node that performs data communications

over the FC link.

Port Address

Also Port Number. The address through which commands are sent to a

host adapter board. This address is assigned by the PCI bus.

Port Number

RAM

See Port Address.

Random Access Memory. The computer’s primary working memory in

which program instructions and data are stored and are accessible to the

CPU. Information can be written to and read from RAM. The contents of

RAM are lost when the computer is turned off.

48.583 p

52.5 pc

A-5

Download from Www.Somanuals.com. All Manuals Search And Download.

3.75 pc

10.25 pc

11.25 pc

38.25 pc

34.5 pc

4.333 pc

Responder

A FC term referring to the answering device.

RISC Core

LSIFC909 chips contain a RISC (Reduced Instruction Set Computer)

processor, programmed through microcode scripts.

ROM

Read Only Memory. Memory from which information can be read but not

changed. The contents of ROM are not erased when the computer is

turned off.

SAN

Storage Area Network.

SCAM

SCSI Conﬁgured AutoMatically. A method to automatically allocate SCSI

IDs using software when SCAM compliant SCSI devices are attached.

Scatter/Gather

A device driver feature that lets the host adapter modify a transfer data

pointer so that a single host adapter transfer can access many segments

of memory. This minimizes interrupts and transfer overhead.

SCB

SCSI Command Block.

SCSI

Small Computer System Interface. A speciﬁcation for a high-performance

peripheral bus and command set. The original standard is referred to as

SCSI-1.

44.25 pc

SCSI-2

The current SCSI speciﬁcation which adds features to the original

SCSI-1 standard.

SCSI ID

A way to uniquely identify each SCSI device on the SCSI bus. Each

SCSI bus has eight available SCSI IDs numbered 0 through 7 (or 0

through 15 for Wide SCSI). The host adapter usually gets ID 7 giving it

priority to control the bus.

Sequence

A term referring to one of the FC “building blocks”, composed of one or

more related frames for a single operation.

SGL

Scatter Gather List.

SNAP

SubNetwork Access Protocol.

Synchronous

Data Transfer

One of the ways data is transferred over the SCSI bus. Transfers are

clocked with ﬁxed frequency pulses. This is faster than asynchronous

data transfer. Synchronous data transfers are negotiated between the

SCSI host adapter and each SCSI device.

48.583 p

52.5 pc

A-6

Glossary of Terms and Abbreviations

Download from Www.Somanuals.com. All Manuals Search And Download.

3.75 pc

10.25 pc

11.25 pc

38.25 pc

34.5 pc

4.333 pc

System BIOS

Controls the low level POST (Power-On Self-Test), and basic operation

of the CPU and computer system.

TID

Target ID.

Topology

ULP

The logical and/or physical arrangement of stations on a network.

Upper Layer Protocol.

VCCI

Voluntary Control Council for Interference.

Space on a hard disk that can be used as if it were RAM.

Vendor Product Data.

Virtual Memory

VPD

Word

A two-byte (or 16-bit) unit of information.

X3T9

A technical committee of the Accredited Standards Committee X3, titled

X3T9 I/O Interfaces. It is tasked with developing standards for moving

data in and out of central computers.

44.25 pc

48.583 p

52.5 pc

A-7

Download from Www.Somanuals.com. All Manuals Search And Download.

3.75 pc

10.25 pc

11.25 pc

38.25 pc

34.5 pc

4.333 pc

44.25 pc

48.583 p

52.5 pc

A-8

Glossary of Terms and Abbreviations

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

floppy disk installation

^{itmpt device driver 4-5}, 4-6

form factor 2-5

adapter properties menu 3-3

atmospheric characteristics 2-6

Fusion-MPT 2-1

heat sink 2-6

host adapter installation 1-1

hot swap 2-4

BSMI 2-6

bus interfaces 2-3

extraction 1-3

installation 1-2

Canadian Compliance Statement 2-6

CE mark 2-6

characteristics

electrical 2-5

installation

cold 1-1

physical 2-5

host adapter board 1-1

hot swap 1-2

itmpt

safety 2-6

cold

extraction 1-3

installation 1-1

command

^{floppy disk 4-5}, 4-6

pkgadd 4-5

volcheck 4-5

^{CompactPCI 2-4}, 2-5

form factor 2-5

hot swap 2-4

LED

^{power 1-1}, 1-3

^{Linux 2-1}, 2-2

device driver 3-1, 4-1

^{installation 3-1}, 4-1

menus

global properties 3-5

device properties menu 3-4

Netware 2-1 , 2-2

electrical characteristics 2-5

electromagnetic compliance 2-6

existing system installation

Solaris itmpt device driver

^{floppy disk installation 4-5}, 4-6

extraction

operating systems

^{Linux 2-1}, 2-2

^{NetWare 2-1}, 2-2

^{SCO OpenServer 2-1}, 2-2

Solaris 2-1

cold environment 1-3

hot swap environment 1-3

hot-swap environment 1-3

^{UnixWare 2-1}, 2-2

FCC Class A 2-6

FCC Self-Certification log 2-6

PCI 2-4, 2-5

physical characteristics 2-5

LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter

IX-1

Download from Www.Somanuals.com. All Manuals Search And Download.

pkgadd 4-5

power

characteristics 2-5

^{LED 1-1}, 1-3

safety characteristics 2-6

^{SCO OpenServer 2-1}, 2-2

SCSI 2-4

^{software support 2-1}, 2-2

Solaris 2-1

storage environment 2-6

technical specifications 2-3, 2-5

atmospheric characteristics 2-6

electrical characteristics 2-5

electromagnetic compliance 2-6

heat sink 2-6

physical characteristics 2-5

power characteristics 2-5

storage environment 2-6

thermal characteristics 2-6

transit environment 2-6

thermal characteristics 2-6

transit environment 2-6

UL flammability rating 2-6

^{UnixWare 2-1}, 2-2

VCCI 2-6

volcheck 4-5

IX-2

Index

Download from Www.Somanuals.com. All Manuals Search And Download.

Customer Feedback

We would appreciate your feedback on this document. Please copy the

following page, add your comments, and fax it to us at the number

shown.

If appropriate, please also fax copies of any marked-up pages from this

document.

Important: Please include your name, phone number, fax number, and

company address so that we may contact you directly for

clariﬁcation or additional information.

Thank you for your help in improving the quality of our documents.

LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter

Download from Www.Somanuals.com. All Manuals Search And Download.

Reader’s Comments

Fax your comments to:

LSI Logic Corporation

Technical Publications

M/S E-198

Fax: 408.433.4333

Please tell us how you rate this document: LSI7202CP CompactPCI Dual

Channel 2 Gbit/s Fibre Channel Host Adapter User’s Guide. Place a

check mark in the appropriate blank for each category.

Excellent Good Average Fair

Poor

____

Completeness of information

Clarity of information

____

Ease of ﬁnding information

Technical content

Usefulness of examples and

illustrations

Overall manual

____

What could we do to improve this document?

If you found errors in this document, please specify the error and page

number. If appropriate, please fax a marked-up copy of the page(s).

Please complete the information below so that we may contact you

directly for clariﬁcation or additional information.

Name

Date

Telephone

Title

Fax

Department

Company Name

Street

Mail Stop

City, State, Zip

Download from Www.Somanuals.com. All Manuals Search And Download.

You can ﬁnd a current list of our U.S. distributors, international distributors, and sales

ofﬁces and design resource centers on our web site at

http://www.lsilogic.com/contacts/na_salesofﬁces.html

Download from Www.Somanuals.com. All Manuals Search And Download.

Lennox Hearth Indoor Fireplace ADK22CMBS User Manual
Lennox Hearth Indoor Fireplace Cambria User Manual
Lenovo Laptop Docking Station 0A33932 User Manual
LG Electronics Microwave Oven MV 1310B User Manual
LG Electronics Range LRE30755SB User Manual
Liebert Automobile Alarm RCM8CE User Manual
Lincoln Electric Welder IM10030 User Manual
Lindy Personal Computer 25018 User Manual
Link electronic Switch PAF 823 User Manual
Logitech Mouse G700 User Manual