7. To show the outdoor temperature, make
sure the number in the sensor reception
icon is the same as the selected channel
in the remote outdoor sensor. If not, press
CH to select the number.
OVERVIEW
FRONT VIEW (FIG. 1)
1. 12 / 24 hr clock, date and alarm area
2. Indoor temperature
0FHC9
First Watch Weather Station
3. Outdoor temperature
NOTE
Displays when batteries are
4. MODE: Change settings or display
5. SNOOZE / LIGHT: Activate snooze function /
Turn on the backlight
USER MANUAL
low.
(FIG. 1)
MEANING
LOCATION
6. MEM: View current, maximum and
minimum temperature
Indoor temperature
area
Main unit batteries low
1
2
Outdoor temperature
area
BACK VIEW (FIG. 2)
Sensor batteries low
1. Wall mount hole
NOTE Press RESET after each battery
2.
/
: Increase / decrease setting
change.
3. AL: View alarm status; set alarm
4. Table stand
3
SENSOR DATA TRANSMISSION
5. CH: Switch remote outdoor sensor display
6. °C / °F: Select temperature unit
7. RESET: Reset unit to default settings
8. Battery compartment
The main unit can collect data from up to 3
sensors.
4
5
6
To search for a sensor:
Simultaneously, press and hold MEM and CH
for 2 seconds.
REMOTE OUTDOOR SENSOR (FIG. 3)
1. LED status indicator
2. Wall mount hole
3. Battery compartment
4. RESET hole
(FIG. 2)
The sensor reception icon in the main unit
shows the status:
ICON
DESCRIPTION
1
2
3
5. CHANNEL switch
Main unit is searching for
sensor(s)
5
6
GETTING STARTED
A sensor has been found
INSERT BATTERIES - REMOTE
OUTDOOR SENSOR
The sensor cannot be found
IMPORTANT Set up the remote outdoor sen-
TIP The transmission range may vary depend-
ing on many factors. You may need to experiment
with various locations to get the best results.
sor first before setting the main unit.
1. Slide open the battery door.
2. Insert the batteries, matching the polarities.
3. Select a channel, then press RESET.
4. Close the battery door.
4
CLOCK
To set the clock:
5. Place the sensor outdoors within 30 m
(98 ft) of the main unit using the wall
mount (see FIG. 4).
1. Press and hold MODE.
7
8
2. Press or to change the settings. (Press
and hold to change the setting quickly.)
3. Press MODE to confirm.
NOTE
4. The settings order is: 12 / 24 hr format,
hour, minute, year, day-month format,
month, day and language.
• Press RESET after each battery change or
channel selection.
(FIG. 3)
• The remote outdoor sensor must be placed
outdoors, and protected from rain and
snow.
2
3
NOTE The language options are English
(E), German (D), French (F), Italian (I), and
Spanish (S).
1
• Use alkaline batteries for longer usage
and consumer grade lithium batteries in
temperatures below freezing.
4
5
To select display mode:
Press MODE to choose between clock with
seconds, clock with weekday and calendar.
ALARM
To set the alarm:
(FIG. 4)
INSERT BATTERIES - MAIN UNIT
1. Press AL to view alarm display.
when the alarm time is displayed.
2. Press and hold AL.
shows
1. Remove the battery door.
2. Insert the batteries, matching the polarities
(see FIG. 2).
3. Press
/
to set hour / minute. (Press
and hold to change the setting quickly.)
4. Press AL to confirm. indicates alarm is
ON.
3. Press RESET.
4. Close the battery door.
5. Place the main unit within 30 m (98 ft) of
the remote outdoor sensor.
To toggle alarms ON / OFF:
6. Wait while the sensor reception icon is
blinking, it is searching for sensor.
1. Press AL to display alarm time.
2. Press AL again to turn alarm ON / OFF.
Download from Www.Somanuals.com. All Manuals Search And Download.
|