LG Electronics Flat Panel Television W1942TQ User Manual

User’s Guide  
W1942TQ  
W2042TQ  
W2242TQ  
Make sure to read the Important Precautions before using the product.  
Keep the User's Guide(CD) in an accessible place for future reference.  
See the label attached on the product and give the information to your  
dealer when you ask for service.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Precautions  
On Installation  
Do not allow anything to rest upon or roll over the power cord, and do not place the  
display where the power cord is subject to damage.  
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,  
laundry tub, in a wet basement, or near a swimming pool.  
Displays are provided with ventilation openings in the cabinet to allow the release of  
heat generated during operation. If these openings are blocked, built-up heat can  
cause failures which may result in a fire hazard. Therefore, NEVER:  
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.  
Place the display in a built-in enclosure unless proper ventilation is provided.  
Cover the openings with cloth or other material.  
Place the display near or over a radiator or heat source.  
Main power breaker is the power cord and this breaking device must be located at  
a location where it is easy to operate.  
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,  
mar, or damage the Active Matrix LCD permanently.  
Do not press the LCD screen with your finger for a long time as this may cause  
some afterimages.  
Some dot defects may appear as Red, Green or Blue spots on the screen.  
However, this will have no impact or effect on the display performance.  
If possible, use the recommended resolution to obtain the best image quality for  
your LCD display. If used under any mode except the recommended resolution,  
some scaled or processed images may appear on the screen. However, this is  
characteristic of the fixed-resolution LCD panel.  
Leaving a fixed image on the screen for a long time may cause damage to the  
screen and cause image burn-in. Make sure to use a screen saver on the product.  
Burn-in and related problems are not covered by the warranty on this product.  
On Cleaning  
Unplug the display before cleaning the face of the display screen.  
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display  
screen because over-spraying may cause electrical shock.  
On Repacking  
Do not throw away the carton and packing materials. They make an ideal  
container in which to transport the unit. When shipping the unit to another  
location, repack it in its original material.  
On Disposal  
The fluorescent lamp used in this product contains a small amount of mercury.  
Do not dispose of this product with general household waste.  
Disposal of this product must be carried out in accordance to the regulations of  
your local authority.  
A2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Connecting the stand  
1.  
Place the monitor with its front facing downward on a soft cloth.  
2.  
Assemble the Stand Body into the product in the correct direction as shown in the picture.  
Make sure you push it until you hear it click”.  
Hinge Body  
Stand Body  
3.  
Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.  
Stand Body  
Stand Base  
4. Tie down the base lock to perpendicularity direction.  
5.  
Once assembled take the monitor up carefully and face  
the front side  
Important  
This illustration depicts the general model of connection. Your monitor may differ from  
the items shown in the picture.  
Do not carry the product upside down holding only the stand base. The product may  
fall and get damaged or injure your foot.  
A3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Disassembling the stand  
1. Put a cushion or soft cloth on aflat  
2. Place the monitor face Down on  
surface.  
the cushion or soft cloth.  
3. Change your lock on the product as it follows and turn it in the arrow direction.  
If you can't release the stand base even the locking knob is at a release  
position, Please push the indicated knob down and retry it.  
4. Pull out the Stand to remove.  
A4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
5. Pushing the PUSH button, Take the stand base from stand body.  
Warning:  
You can hurt your finger.  
Good Position  
Bad Position  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Positioning your display  
1. Adjust the position of the panel in various ways for maximum comfort.  
Tilt Range : -5˚~20˚  
Ergonomic  
It is recommended that in order to maintain an ergonomic and comfortable viewing  
position, the forward tilt angle of the monitor should not exceed 5 degrees.  
A5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Using the Computer  
1. Make sure to turn off the computer and product. Connect the cable as below sketch map  
1
2
form  
to  
.
NOTE  
This is a simplified representation of the rear view.  
This rear view represents a general model; your display may differ from the view as  
shown.  
User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with  
ferrite cores to maintain standard compliance for the product.  
A
B
C
Connect DVI Cable  
Connect Dsub Cable (PC)  
Connect Dsub Cable (Mac)  
Analog signal Digital signal  
Power Cord  
D-sub  
DVI  
PUSH  
Wall-outlet type  
PC  
PC-outlet type  
PC  
B
c
MAC  
Mac adapter  
For Apple Macintosh use, a separate plug adapter is  
needed to change the 15 pin high density (3 row) D-  
sub VGA connector on the supplied cable to a 15 pin  
2 row connector.  
PC  
A
DVI-D(This feature is not available in all countries.)  
2. Press  
button on the front switch panel to turn the  
power on. When monitor power is turned on, the  
'Self Image Setting Function' is executed automatically.  
(Only Analog Mode)  
NOTE  
‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user  
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual  
input signals.  
‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted  
screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve  
resolution.  
A6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Panel Functions  
Front Panel Controls  
Control  
Function  
To select the image size of the screen.  
4:3 in Wide  
WIDE  
4:3  
WIDE : Switch to full screen mode according to input  
image signal.  
4 : 3 : Change the image signal ratio into 4:3.  
Use this button to enter or exit the On Screen Display.  
MENU Button  
OSD LOCKED/UNLOCKED  
This function allows you to lock the current control  
settings, so that they cannot be inadvertently changed.  
Press and hold the MENU button for several seconds.  
The message "OSD LOCKED" should appear.  
You can unlock the OSD controls at any time by pushing  
the MENU button for several seconds. The message  
"OSD UNLOCKED" should appear.  
A7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Panel Functions  
Control  
Function  
Use these buttons to select or adjust functions in the  
On Screen Display.  
Buttons  
For more information, refer to page A15.  
Use this button to make D-Sub or DVI connector  
active. This feature is used when two computers are  
connected to the display. The default setting is D-Sub.  
Use this button to enter a selection in the On Screen  
Display.  
AUTO/SET  
Button  
AUTO IMAGE ADJUSTMENT  
When adjusting your display settings, always press  
the AUTO/SET button before entering the On Screen  
Display(OSD). This will automatically adjust your  
display image to the ideal settings for the current  
screen resolution size (display mode).  
The best display mode is  
-
-
W1942TQ : 1440 x 900  
W2042TQ/W2242TQ : 1680 x 1050  
Power Button  
Use this button to turn the display on or off.  
This Indicator lights up blue when the display  
operates normally(On Mode). If the display is in Sleep  
Mode (Energy Saving), this indicator color changes  
to amber.  
Power Indicator  
A8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display (OSD) Control Adjustment  
Screen Adjustment  
Making adjustments to the image size, position and operating parameters of  
the display is quick and easy with the On Screen Display Control system.  
A short example is given below to familiarize you with the use of the controls.  
The following section is an outline of the available adjustments and selections  
you can make using the OSD.  
NOTE  
Allow the display to stabilize for at least 30 minutes before making image adjustments.  
To make adjustments in the On Screen Display, follow these steps:  
AUTO/SET  
MENU  
MENU  
Press the MENU Button, then the main menu of the OSD appears.  
To access a control, use the  
or  
Buttons. When the icon you want  
becomes highlighted, press the AUTO/SET Button.  
Use the  
/
Buttons to adjust the image to the desired level. Use the  
AUTO/SET Button to select other sub-menu items.  
Push the MENU Button once to return to the main menu to select another  
function. Push the MENU Button twice to exit from the OSD.  
A9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
The following table indicates all the On Screen Display control, adjustment,  
and setting menus.  
Main menu  
Sub-menu  
BRIGHTNESS  
CONTRAST  
GAMMA  
A
D
Reference  
PICTURE  
To adjust the brightness,  
contrast and gamma of the  
screen  
sRGB  
To customize the color of  
the screen  
COLOR  
PRESET  
6500K  
9300K  
RED  
GREEN  
BLUE  
To adjust the position of the  
screen  
HORIZONTAL  
VERTICAL  
CLOCK  
TRACKING  
SETUP  
To improve the clarity and  
stability of the screen  
PHASE  
SHARPNESS  
LANGUAGE  
To customize the screen  
status for a user's operating  
environment  
OSD  
HORIZONTAL  
POSITION VERTICAL  
WHITE BALANCE  
RTC  
POWER INDICATOR  
FACTORY RESET  
MOVIE  
FLATRON  
F-ENGINE  
To select or customize  
desired image settings  
INTERNET  
USER  
NORMAL  
DEMO  
: Adjustable  
A : Analog Input  
D : Digital Input  
NOTE  
The order of icons may differ depending on the model (A10~A15).  
A10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
Press the MENU Button, then the main menu of the OSD appears.  
Main Menu  
MENU  
: Exit  
: Adjust (Decrease/Increase)  
: Enter  
SET  
: Select another sub-menu  
Button Tip  
Sub-menus  
Menu Name  
Icons  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
PICTURE  
PICTURE  
BRIGHTNESS  
To adjust the brightness of the screen.  
To adjust the contrast of the screen.  
CONTRAST  
GAMMA  
Set your own gamma value. : -50/0/50  
On the monitor, high gamma values  
display whitish images and low gamma  
values display high contrast images.  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another sub-menu  
COLOR  
COLOR  
Select the screen color.  
PRESET  
• sRGB: Set the screen color to fit the  
SRGB standard color  
specification.  
• 6500K: Slightly reddish white.  
• 9300K: Slightly bluish white.  
Set your own red color levels.  
Set your own green color levels.  
Set your own blue color levels.  
RED  
GREEN  
BLUE  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another sub-menu  
A12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
TRACKING  
TRACKING  
To move image left and right.  
To move image up and down.  
HORIZONTAL  
VERTICAL  
CLOCK  
To minimize any vertical bars or stripes  
visible on the screen background.  
The horizontal screen size will also  
change.  
PHASE  
To adjust the focus of the display.  
This item allows you to remove any  
horizontal noise and clear or sharpen  
the image of characters.  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another  
SHARPNESS  
To adjust the clearness of the screen.  
sub-menu  
A13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
To choose the language in which the  
control names are displayed.  
LANGUAGE  
SETUP  
SETUP  
OSD  
POSITION  
To adjust position of the OSD window  
on the screen.  
WHITE  
BALANCE  
If the output of the video card is different  
the required specifications, the color level  
may deteriorate due to video signal  
distortion. Using this function, the signal  
level is adjusted to fit into the standard  
output level of the video card in order to  
provide the optimal image.  
Activate this function when white and  
black colors are present in the screen.  
If you set ON, you enable the Response  
Time Control function.  
RTC  
If you set OFF, you disable the  
Response Time Control function.  
MENU : Exit  
: Adjust  
: Adjust  
Use this function to set the power  
indicator on the front side of the monitor  
to ON or OFF.  
POWER  
INDICATOR  
SET : Select another  
sub-menu  
If you set OFF, it will go off.  
If you set ON at any time, the power  
indicator will automatically be turned on.  
Restore all factory default settings except  
FACTORY  
RESET  
"LANGUAGE."  
Press the  
button to reset immediately.  
If this does not improve the screen image, restore the factory default settings.  
If necessary, perform the white balance function again. This function will be enabled only  
when the input signal is an analog signal.  
A14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
The OSD screen will appear when you touch the  
button on the left side  
of the monitor.  
Menu Name  
Icons  
Sub-menu Name  
Main menu  
Sub menu  
Description  
This feature lets you easily select the best desired  
image condition optimized to the environment  
MOVIE  
INTERNET (ambient illumination, image types etc).  
MOVIE: For animation images in videos or movies  
INTERNET: For text images (Word processing etc.)  
USER  
User  
You can manually adjust brightness, ACE or RCM.  
You can save or restore the adjusted value even  
when using a different environment.  
...  
(Brightness): Adjusts screen brightness.  
...  
ACE(Adaptive Clarity Enhancer): Selects the clarity mode.  
...  
RCM(Real Color Management): Selects the color mode.  
0
Not applied  
1
Green enhance  
2
Flesh tone  
3
Color Enhance  
Select the  
sub-menu using the AUTO/SET  
button and save the YES value using the  
buttons.  
,
NORMAL  
DEMO  
This is under normal operating conditions.  
This is just for advertising to customer in the  
shops. It’s setting is same with Movie mode and  
screen is divided by half.  
A15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Check the following before calling for service.  
No image appears  
G Is the power cord of the  
Check and see if the power cord is connected  
properly to the power outlet.  
display connected?  
G Is the power on and the  
power indicator blue or  
green?  
Adjust the brightness and the contrast.  
G Is the power indicator  
If the display is in power saving mode, try moving  
the mouse or pressing any key on the keyboard to  
bring up the screen.  
amber?  
• Try to turn on the PC  
.
G Do you see an "OUT OF  
RANGE" message on  
the screen?  
This message appears when the signal from the  
PC (video card) is out of horizontal or vertical  
frequency range of the display. See the  
'Specifications' section of this manual and  
configure your display again.  
This message appears when the signal cable  
between your PC and your display is not  
connected. Check the signal cable and try again.  
G Do you see a "CHECK  
SIGNAL CABLE"  
message on the  
screen?  
Do you see a "OSD LOCKED" message on the screen?  
G
Do you see OSD  
LOCKEDwhen you  
push MENU button?  
• You can secure the current control settings,  
so that they cannot be inadvertently changed.  
You can unlock the OSD controls at any time  
by pushing the MENU button for several  
seconds: the message  
OSD UNLOCKEDwill appear.  
A16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Display image is incorrect  
G Display Position is  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, adjust the image  
position using the H position and V position icon  
in the on screen display.  
incorrect.  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
vertical bars or stripes using the CLOCK icon in  
the on screen display.  
G On the screen  
background, vertical  
bars or stripes are  
visible.  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
horizontal bars using the PHASE icon in the on  
screen display.  
Check Control Panel --> Display --> Settings  
and adjust the display to the recommended  
resolution or adjust the display image to the ideal  
setting. Set the color setting higher than 24 bits  
(true color).  
G Any horizontal noise  
appearing in any  
image or characters  
are not clearly  
portrayed.  
Important  
Check Control Panel --> Display --> Settings and see if the frequency or the  
resolution were changed. If yes, readjust the video card to the recommend  
resolution.  
Reasons for Recommending Optimal Resolution : The aspect ratio is 16:10.  
If the input resolution is not 16:10 (for instance, 16:9, 5:4, 4:3), you might encounter  
problems such as blurred letters, blurry screen, cut-off screen display or tilted screen.  
The setting method can differ by computer and O/S (Operation System),  
and resolution mentioned above may not be supported by the video card  
performance. In this case, please ask to the computer or the video card  
manufacturer  
.
A17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Display image is incorrect  
G The screen color is  
Check if the signal cable is properly connected  
and use a screwdriver to fasten if necessary.  
Make sure the video card is properly inserted in  
the slot.  
Set the color setting higher than 24 bits (true color)  
at Control Panel - Settings.  
mono or abnormal.  
G The screen blinks.  
Check if the screen is set to interlace mode and if  
yes, change it to the recommend resolution.  
Have you installed the display driver?  
G
Have you installed the  
display driver?  
Be sure to install the display driver from the display  
driver CD (or diskette) that comes with your  
display. Or, you can also download the driver from  
Make sure to check if the video card supports  
Plug&Play function.  
G
Do you see an  
"Unrecognized monitor,  
Plug&Play (VESA DDC)  
monitor found"  
message?  
A18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
W1942TQ  
Display  
19 inches (48.1 cm) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Visible diagonal size: 48.1 cm  
0.285*0.285 mm pixel pitch  
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)  
Digital : 30 - 83 kHz (Automatic)  
Sync Input  
Vertical Freq.  
Input Form  
56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green)  
Digital (HDCP)  
Signal Input  
15 pin D-Sub Connector  
Video Input  
DVI - D Connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Analog : VESA 1440 x 900 @ 75 Hz  
Digital : VESA 1440 x 900 @ 60 Hz  
VESA 1440 x 900 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B  
Power  
Consumption  
:
36W(Typ.)  
1 W  
1 W  
On Mode  
Sleep Mode  
Off Mode  
Dimensions  
& Weight  
With Stand  
Without Stand  
Width 44.84 cm / 17.65 inches 44.84 cm / 17.65 inches  
Height 38.33 cm / 15.09 inches 30.07 cm / 11.84 inches  
Depth 19.84 cm / 7.81 inches  
6.32 cm / 2.49 inches  
Net  
Tilt  
4.1 kg (9.11 lbs)  
-5˚~ 20˚  
Tilt Range  
AC 100-240V~ 50/60Hz 0.8A  
Power Input  
Operating Conditions  
Environmental  
Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Stand Base  
Power cord  
Attached ( ), Detached ( O )  
Wall-outlet type or PC-outlet type  
NOTE  
Information in this document is subject to change without notice.  
A19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
W2042TQ  
Display  
20.1 inches (51.1 cm) Flat Panel Active matrix-TFT LCD Anti-  
Glare coating  
Visible diagonal size: 51.1 cm  
0.258*0.258 mm pixel pitch  
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)  
Digital : 30 - 83 kHz (Automatic)  
Sync Input  
Video Input  
Vertical Freq.  
Input Form  
56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green), Digital (HDCP)  
Signal Input  
15 pin D-Sub Connector  
DVI - D connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Analog : VESA 1680 x 1050 @60 Hz  
Digital : VESA 1680 x 1050 @60 Hz  
VESA 1680 x 1050 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B  
Power  
Consumption  
:
40W(Typ.)  
1 W  
1 W  
On Mode  
Sleep Mode  
Off Mode  
Dimensions  
& Weight  
With Stand  
Without Stand  
Width 47.39 cm / 18.66 inches 47.39 cm / 18.66 inches  
Height 39.04 cm / 15.37 inches 31.89 cm / 12.56 inches  
Depth 19.84 cm / 7.81 inches  
6.29 cm / 2.48 inches  
Net  
Tilt  
4.5 kg (10 lbs)  
-5˚~ 20˚  
Tilt Range  
AC 100-240V~ 50/60Hz 1.0A  
Power Input  
Operating Conditions  
Environmental  
Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type or PC-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
A20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
W2242TQ  
22 inches (55.8 cm) Flat Panel Active matrix-TFT LCD, Anti-  
Glare coating  
Display  
Visible diagonal size: 55.8 cm  
0.282*0.282 mm pixel pitch  
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)  
Digital : 30 - 83 kHz (Automatic)  
Sync Input  
Video Input  
Vertical Freq.  
Input Form  
56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green), Digital (HDCP)  
Signal Input  
15 pin D-Sub Connector  
DVI - D connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Resolution  
Plug&Play  
Analog : VESA 1680 x 1050 @60 Hz  
Digital : VESA 1680 x 1050 @60 Hz  
VESA 1680 x 1050 @60 Hz  
Recommend  
DDC 2B  
Power  
Consumption  
:
40W(Typ.)  
1 W  
1 W  
On Mode  
Sleep Mode  
Off Mode  
Dimensions  
& Weight  
With Stand  
Without Stand  
Width 51.57 cm / 20.30 inches 51.57 cm / 20.30 inches  
Height 41.80 cm / 16.46 inches 34.46 cm / 13.57 inches  
Depth 20.94 cm / 8.24 inches  
6.31 cm / 2.48 inches  
4.65 kg (10.33 lbs)  
-5˚~ 20˚  
Net  
Tilt  
Tilt Range  
AC 100-240V~ 50/60Hz 1.0A  
Power Input  
Environmental  
Conditions  
Operating Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type or PC-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
A21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Preset Modes (Resolution)  
W1942TQ  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
70  
70  
60  
75  
60  
75  
75  
60  
75  
75  
65  
60  
75  
60  
60  
75  
1
2
640 x 350  
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1152 x 870  
1152 x 900  
1280 x 1024  
1280 x 1024  
1440 x 900  
1440 x 900  
1440 x 900  
31.469  
31.468  
31.469  
37.500  
37.879  
46.875  
49.725  
48.363  
60.123  
68.681  
61.805  
63.981  
79.976  
55.500  
55.935  
70.635  
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
*15  
**16  
*Recommend Mode  
**Only Analog Mode  
W2042TQ/W2242TQ  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
720 x 400  
640 x 480  
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
63.981  
79.976  
64.674  
65.290  
70  
60  
75  
60  
75  
60  
75  
75  
60  
75  
60  
60  
3
640 x 480  
4
800 x 600  
800 x 600  
5
6
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 1024  
1280 x 1024  
1680 x 1050  
1680 x 1050  
7
8
9
10  
11  
*12  
*Recommend Mode  
Indicator  
LED Color  
MODE  
blue  
amber  
Off  
On Mode  
Sleep Mode  
Off Mode  
A22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Wall mount plate  
This monitor satisfies the specifications of the Wall mount plate or  
the interchange device.  
1. Place the monitor with its front facing downward on a soft cloth.  
2. Separate the stand by pushing the PUSH button.  
Good Position  
Bad Position  
Warning:  
You can hurt your finger.  
3. Install the Wall mount plate.  
Wall mount plate(Separate purchase)  
This is stand-type or wall mount type and is  
connectable with Wall mount plate.  
Please refer to the installation guide for more  
details, which is provided when Wall mount  
plate is purchased.  
Kensington Security Slot  
Connected to a locking cable that can be  
purchased separately at most computer stores.  
A23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Digitally yours  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Kyocera Fax Machine FS C2126MFP User Manual
Linear Fryer DXS 10 User Manual
LOREX Technology Security Camera SG7125 User Manual
Makita Drill DA4030 User Manual
Makita Impact Driver 6940D User Manual
Marshall Amplification Radio MT 1 User Manual
Maytag Gas Grill JA460 User Manual
Meade Telescope 114 EQ ASB User Manual
Memorex Cordless Telephone MPH6929 User Manual
Memorex TV VCR Combo MVT2135B User Manual