LG Electronics Computer Monitor E1950T User Manual

User’s Guide  
E1950T  
E2050T  
E2250T  
E2350T  
Make sure to read the Important Precautions before using the  
product. Keep the User's Guide(CD) in an accessible place for future  
reference.  
See the label attached on the product and give the information to  
your dealer when you ask for service.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Precautions  
On Installation  
Do not allow anything to rest upon or roll over the power cord, and do not place the  
display where the power cord is subject to damage.  
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,  
laundry tub, in a wet basement, or near a swimming pool.  
Displays are provided with ventilation openings in the cabinet to allow the release  
of heat generated during operation. If these openings are blocked, built-up heat  
can cause failures which may result in a fire hazard. Therefore, NEVER:  
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.  
Place the display in a built-in enclosure unless proper ventilation is provided.  
Cover the openings with cloth or other material.  
Place the display near or over a radiator or heat source.  
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,  
mar, or damage the Active Matrix LCD permanently.  
Do not press the LCD screen with your finger for a long time as this may cause  
some afterimages.  
Some dot defects may appear as Red, Green or Blue spots on the screen.  
However, this will have no impact or effect on the display performance.  
If possible, use the recommended resolution to obtain the best image quality for  
your LCD display. If used under any mode except the recommended resolution,  
some scaled or processed images may appear on the screen. However, this is  
characteristic of the fixed-resolution LCD panel.  
Leaving a fixed image on the screen for a long time may cause damage to the  
screen and cause image burn-in. Make sure to use a screen saver on the product.  
Burn-in and related problems are not covered by the warranty on this product.  
Do not shock or scratch the front and sides of the screen with metallic objects.  
Otherwise, it may cause damage to the screen.  
Make sure the panel faces forward and hold it with both hands to move. If you  
drop the product, the damaged product can cause electric shock or fire. Contact  
an authorized the service center for repair.  
Avoid high temperatures and humidity.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Precautions  
On Cleaning  
Unplug the display before cleaning the face of the display screen.  
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display  
screen because over-spraying may cause electrical shock.  
When cleaning the product, unplug the power cord and scrub gently with a soft  
cloth to prevent scratching. Do not clean with a wet cloth or spray water or other  
liquids directly onto the product. An electric shock may occur. (Do not use  
chemicals such as benzene, paint thinners or alcohol)  
Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;  
wipe in one direction only. Too much moisture may cause staining.  
On Repacking  
Do not throw away the carton and packing materials. They make an ideal  
container in which to transport the unit. When shipping the unit to another  
location, repack it in its original material.  
On Disposal  
The fluorescent lamp used in this product contains a small amount of mercury.  
Do not dispose of this product with general household waste.  
Disposal of this product must be carried out in accordance to the regulations of  
your local authority.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessories  
!!! Thank for selecting LGE products !!!  
Please make sure the following items are included with your  
monitor. If any items are missing, contact your dealer.  
15-pin D-Sub Signal Cable  
User's Guide/Cards  
(To set it up, this signal cable may  
be attached to this product before  
shipping out.)  
Or  
AC-DC adapter  
Power Cord  
AC-DC adapter  
(Depending on the country)  
(Depending on the country)  
DVI-D Signal Cable  
(This feature is not available in  
all countries.)  
NOTE  
This accessories may look different from those shown here.  
User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite  
cores to maintain standard compliance for the product.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
1 way stand  
1. Place the monitor with its front facing downward on a soft cloth.  
2. Use a coin on the back of the stand base and turn the screw clockwise to tighten.  
3. Once assembled take the monitor up carefully and face the front side  
.
4. When you desire to disintegrate the monitor from the stand base, use a coin to turn the  
screw counterclockwise.  
Important  
This illustration depicts the general model of connection. Your monitor may differ from  
the items shown in the picture.  
Do not carry the product upside down holding only the stand base. The product may  
fall and get damaged or injure your foot.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
2 way stand  
1. Place the monitor with its front facing downward on a soft cloth.  
2. Press the button as shown, and pull the stand body up.  
3. After pull the stand body up,take the monitor up carefully and face the front side.  
(Once you pull the stand body up, please keep pressing the button.If you don’t  
press the button, it will damage the product.)  
When limited tilt degree, the button  
is not working, pull stand body up or  
down a little.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
4. If you want to use the stand base,pull the stand body down.  
(Once you pull the stand body down, please keep pressing the button.If you don’t  
press the button, it will damage the product.)  
5. Use a coin on the back of the stand base and turn the screw clockwise to tighten.  
6. Once assembled take the monitor up carefully and face the front side  
.
Important  
This illustration depicts the general model of connection. Your monitor may differ from  
the items shown in the picture.  
Do not carry the product upside down holding only the stand base. The product may  
fall and get damaged or injure your foot.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor,  
the computer system, and other attached devices is turned off.  
Positioning your display  
After installation, adjust the angle as shown below.  
* With stand base  
Adjust the position of the panel in various ways for maximum comfort.  
Tilt Range : -5˚ - 15˚  
Do not touch or press the screen when  
adjusting the angle of the monitor.  
When adjusting the angle of the screen, do  
not put your finger(s) in between the head of  
the monitor and the stand body. You can  
hurt your finger(s).  
ERGONOMIC  
It is recommended that in order to maintain an ergonomic and comfortable viewing position,  
the forward tilt angle of the monitor should not exceed 5 degrees.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor,  
the computer system, and other attached devices is turned off.  
Positioning your display  
* Without stand base  
Ergonomic  
It is recommended that in order to maintain an ergonomic and comfortable viewing position, the  
backward tilt angle of the monitor should exceed 10 degrees.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Connecting with the PC  
1. Before setting up the monitor, ensure that the power to the monitor, the computer  
2. sCyosntenmec, tasnidgnoathleinrpautttaccahbedledeviceasnids ptuorwneedr ocoff.rd  
in order, then tighten the screw  
1
2
of the signal cable.  
A
Connect DVI-D(Digital signal) Cable  
B
Connect D-sub(Analog signal) Cable  
When using a D-Sub signal input cable connector  
for Macintosh  
Mac adapter :For Apple Macintosh use, a  
separate plug adapter is needed to change the  
15 pin high density (3 row) D-sub VGA  
connector on the supplied cable to a 15 pin 2  
row connector.  
Varies according to model.  
DVI-D (This feature is not available in all countries.)  
Wall-outlet type  
OR  
NOTE  
This is a simplified representation of the rear view.  
This rear view represents a general model; your display may  
differ from the view as shown.  
Wall-outlet type  
3. Press the power button on the front panel to turn the power on. When monitor power is  
turned on, the 'Self Image Setting Function' is executed automatically.  
(Only Analog Mode)  
Power Button  
NOTE  
‘ Self Image Setting Function’? This function provides the user with optimal display  
settings.When the user connects the monitor for the first time, this function automatically adjusts  
the display to optimal settings for individual input signals.  
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen  
flicker or tilted screen while using the device or after changing screen resolution, press the  
AUTO function button to improve resolution.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Panel Functions  
Front Panel Controls  
MENU Button  
OSD LOCKED/UNLOCKED  
This function allows you to lock the current control  
settings, so that they cannot be inadvertently changed.  
Press and hold the MENU button for several seconds.  
The message "OSD LOCKED" should appear.  
You can unlock the OSD controls at any time by pushing  
the MENU button for several seconds. The message  
"OSD UNLOCKED" should appear.  
SMART+ Button  
Use this button to enter AUTO BRIGHT,ORIGINAL  
RATIO, DUAL WEB,CINEMA MODE menus.  
For more information, refer to page 19~21.  
ENGINE Button  
For more information, refer to page 22~23.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Panel Functions  
AUTO Button  
AUTO IMAGE ADJUSTMENT  
When adjusting your display settings, always press  
the AUTO button before entering the On Screen  
Display(OSD). (Only Analog Mode)  
This will automatically adjust your display image to  
the ideal settings for the current screen resolution  
size (display mode).  
The best display mode is  
E1950T : 1360 x 768  
E2050T : 1600 x 900  
E2250T : 1920 x 1080  
E2350T : 1920 x 1080  
Use this button to select source from input.  
INPUT Button  
(SOURCE Hot key)  
When two input signals are connected, you can select the  
input signal (D-SUB/DVI) you want. When only one signal  
is connected, it is automatically detected. The default  
setting is D-Sub.  
EXIT Button  
Exit the OSD(On Screen Display).  
Use this button to turn the display on or off.  
Power Button &  
Power Indicator  
From front view,the power indicator stays purple if the  
display is running properly (On Mode). If the display  
is in Sleep Mode (Energy Saving), the power indicator  
is blinking purple.  
Light Sensor  
This is lens for light sensor detect outside luminance,  
when setting AUTO BRIGHT ON.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display (OSD) Control Adjustment  
Screen Adjustment  
Making adjustments to the image size, position and operating  
parameters of the display is quick and easy with the On Screen  
Display Control system.  
A short example is given below to familiarize you with the use of the  
controls. The following section is an outline of the available  
adjustments and selections you can make using the OSD.  
To make adjustments in the On Screen Display, follow these steps:  
Press the discretionary Button, then the main menu of the OSD appears.  
1
To access a control, use the corresponding Buttons.  
2
Use the  
Use the  
/
Buttons to adjust the image to the desired level.  
3
4
Button to select other sub-menu items.  
Press the EXIT Button to exit from the OSD.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
The following table indicates all the On Screen Display control, adjustment,  
and setting menus.  
DSUB : D-SUB(Analog signal) input  
DVI-D : DVI-D(Digital signal) input  
Main menu  
PICTURE  
Sub-menu  
BRIGHTNESS  
Supported input  
Description  
To adjust the brightness, contrast  
and sharpness of the screen  
DSUB  
DVI-D  
CONTRAST  
SHARPNESS  
To customize the color of the  
screen  
COLOR TEMP  
(PRESET / USER)  
DSUB  
DVI-D  
COLOR  
GAMMA  
HORIZONTAL  
VERTICAL  
To adjust the position of the  
screen  
DISPLAY  
DSUB  
DSUB  
CLOCK  
PHASE  
To improve the clarity and  
stability of the screen  
DSUB  
DVI-D  
LANGUAGE > ENGLISH  
POWER INDICATOR  
BUTTON INDICATOR  
OTHERS  
To customize the screen status  
for a user's operating  
environment  
DSUB  
WHITE BALANCE  
FACTORY RESET  
DSUB  
DVI-D  
DSUB  
DVI-D  
AUTO BRIGHT  
ORIGINAL RATIO  
DUAL WEB  
SMART+  
To adjust the image size  
CINEMA MODE  
DSUB  
DVI-D  
NORMAL  
MOVIE  
F-ENGINE  
To select or customize desired  
image settings  
INTERNET  
DEMO  
NOTE  
The order of icons may differ depending on the model (14~23).  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
Press the MENU Button, then the main menu of the OSD appears.  
Menu Name  
Sub-  
menus  
Icons  
Button  
Tip  
Exit  
Adjust (Decrease/Increase)  
Select another sub-menu  
Restart to select sub-menu  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
To adjust the brightness of the screen.  
To adjust the contrast of the screen.  
To adjust the clearness of the screen.  
BRIGHTNESS  
CONTRAST  
SHARPNESS  
Exit : Exit  
: Decrease  
: Increase  
: Select another sub-menu  
: Restart to select sub-menu  
COLOR TEMP  
Select the screen color.  
• sRGB: Set the screen color to fit the  
sRGB standard color  
specification.  
• 6500K-7500K: Red screen color.  
• 8500K-9300K: Blue screen color.  
PRESET  
USER  
RED  
Exit : Exit  
Set your own red color levels.  
: Decrease  
GREEN  
: Increase  
: Select another sub-menu  
: Restart to select sub-menu  
Set your own green color levels.  
BLUE  
Set your own blue color levels.  
GAMMA  
Set your own gamma value. : 0 / 1 / 2  
On the monitor, high gamma values  
display whitish images and low  
gamma values display blackish  
images.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
D-SUB input  
HORIZONTAL  
To move image left and right.  
To move image up and down.  
VERTICAL  
CLOCK  
To minimize any vertical bars or  
stripes visible on the screen  
background.  
The horizontal screen size will also  
change.  
DVI-D input  
To adjust the focus of the display.  
This item allows you to remove any  
horizontal noise and clear or sharpen  
the image of characters.  
PHASE  
Exit : Exit  
: Decrease  
: Increase  
: Select another sub-menu  
: Restart to select sub-menu  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
To choose the language in which the  
control names are displayed.  
LANGUAGE  
Use this function to set the power  
indicator on the front side of the monitor  
to ON or OFF.  
POWER  
INDICATOR  
If you set OFF, it will be turned off.  
If you set ON at any time, the power  
indicator will automatically be turned on.  
Exit : Exit  
Use this function to set the control key  
indicator on the front side of the monitor  
to ON or OFF.  
If you set OFF, it will be turned off.  
If you set ON, it will be turned on.  
BUTTON  
INDICATOR  
: Decrease  
: Increase  
: Select another sub-menu  
: Restart to select sub-menu  
WHITE  
BALANCE  
If the output of the video card is  
different the required specifications,  
the color level may deteriorate due  
to video signal distortion. Using this  
function, the signal level is adjusted  
to fit into the standard output level of  
the video card in order to provide the  
optimal image.  
Activate this function when white  
and black colors are present in the  
screen.  
Restore all factory default settings except  
FACTORY  
RESET  
"LANGUAGE."  
Press the  
,
buttons to reset  
immediately.  
NOTE  
If this does not improve the screen image, restore the factory default settings. If necessary, execute the  
WHITE BALANCE function again. This function will be enabled only when the input signal is an analog  
signal.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
Press the SMART+ Button, then the main menu of the OSD appears.  
Menu Name  
Sub-  
menus  
Icons  
Button  
Tip  
Exit  
Move  
Restart to select sub-menu  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
If select on,it automatically controls the  
brightness of display to best suit the  
surrounding working environment,providing  
the optimal viewing condition and maximized  
user convenience.  
If select off,auto brightness is off.  
Switch to full screen mode according to input  
image signal.  
*This function works only if input resolution is  
lower than monitor ratio (16:9).  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
* Before using below functions, please install Easy Set Packge programme.  
Help user to browse web efficiently by dividing in half.  
Help to arrange and move windows on screen.  
Help user to control divided windows ratio.  
Make the eye comfortable by reducing the  
background brightness in the web page.  
Exit : Exit  
,
: Move  
: Restart to select sub-menu  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
ENGINE  
Press the  
Button, then the main menu of the OSD appears.  
Menu Name  
Sub-  
menus  
Icons  
Button  
Tip  
Exit  
Move  
Restart to select sub-menu  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
NORMAL  
Select this when you want to use the product  
in the most general using environment.  
MOVIE  
Select this when you are watching a video or  
movie.  
INTERNET  
Select this when you are working on the  
document (Word etc.)  
DEMO  
This is used for advertising in the store. The  
screen will be divided to show the standard  
mode on the left and video mode on the right so  
that the consumers can check the difference  
after applying the video mode.  
Exit : Exit  
: Move  
: Restart to select sub-menu  
,
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Check the following before calling for service.  
No image appears  
G Is the power cord of the  
Check and see if the power cord is connected  
properly to the power outlet.  
display connected?  
G Is the power indicator  
Press the Power button.  
light on?  
G Is the power indicator  
If the display is in power saving mode, try moving  
the mouse or pressing any key on the keyboard to  
bring up the screen.  
flickering?  
• Try to turn on the PC  
.
G Do you see an "OUT OF  
RANGE" message on  
the screen?  
This message appears when the signal from the  
PC (video card) is out of horizontal or vertical  
frequency range of the display. See the  
'Specifications' section of this manual and  
configure your display again.  
This message appears when the signal cable  
between your PC and your display is not  
connected. Check the signal cable and try again.  
G Do you see a "CHECK  
SIGNAL CABLE"  
message on the  
screen?  
Do you see a "OSD LOCKED" message on the screen?  
G
Do you see OSD  
LOCKEDwhen you  
push MENU button?  
• You can secure the current control settings,  
so that they cannot be inadvertently changed.  
You can unlock the OSD controls at any time  
by pushing the MENU button for several  
seconds: the message  
OSD UNLOCKEDwill appear.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Display image is incorrect  
G Display Position is  
Press the AUTO button to automatically adjust  
your display image to the ideal setting.  
If the results are unsatisfactory, adjust the image  
position using the H position and V position icon  
in the on screen display.  
incorrect.  
Press the AUTO button to automatically adjust  
your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
vertical bars or stripes using the CLOCK icon in  
the on screen display.  
G On the screen  
background, vertical  
bars or stripes are  
visible.  
Press the AUTO button to automatically adjust  
your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
horizontal bars using the PHASE icon in the on  
screen display.  
Check Control Panel --> Display --> Settings  
and adjust the display to the recommended  
resolution or adjust the display image to the ideal  
setting. Set the color setting higher than 24 bits  
(true color).  
G Any horizontal noise  
appearing in any  
image or characters  
are not clearly  
portrayed.  
IMPORTANT  
Check Control Panel --> Display --> Settings and see if the frequency or the  
resolution were changed. If yes, readjust the video card to the recommend  
resolution.  
If the recommended resolution (optimal resolution) is not selected, letters may be  
blurred and the screen may be dimmed, truncated or biased. Make sure to select  
the recommend resolution.  
The setting method can differ by computer and O/S (Operation System),  
and resolution mentioned above may not be supported by the video card  
performance. In this case, please ask to the computer or the video card  
manufacturer.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Display image is incorrect  
G The screen color is  
Check if the signal cable is properly connected  
and use a screwdriver to fasten if necessary.  
Make sure the video card is properly inserted in  
the slot.  
Set the color setting higher than 24 bits (true color)  
at Control Panel - Settings.  
mono or abnormal.  
G The screen blinks.  
Check if the screen is set to interlace mode and if  
yes, change it to the recommend resolution.  
Do you see an "Unrecognized monitor, Plug&Play (VESA  
DDC) monitor found" message?  
G
Have you installed the  
display driver?  
Be sure to install the display driver from the display  
driver CD (or diskette) that comes with your  
display. Or, you can also download the driver from  
Make sure to check if the video card supports  
Plug&Play function.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E1950T  
47.0 cm (18.5 inches) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 47.0 cm  
0.300 x 0.300 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 - 61 kHz (Automatic)  
56 - 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
VESA 1360 x 768 @ 60 Hz  
VESA 1360 x 768 @ 60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B(Digital),DDC2AB(Anlaog)  
:
14 W(Typ.)  
1 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 45.90 cm (18.07 inches)  
Height 37.50 cm (14.76 inches)  
Depth 19.80 cm ( 7.80 inches)  
Width 45.90 cm (18.07 inches)  
Height 29.70 cm (11.69 inches)  
Depth 3.60 cm ( 1.41 inches)  
Weight(excl. packing)  
2.4 kg (5.29 lbs)  
Tilt : -5˚ - 15˚  
Range  
12V  
2.0A  
Power Input  
AC-DC Adapter  
Type ADS-24S-12 1224G*,manufactured by HONOR Electronic  
or type MU24-B120200-xx,manufactured by LEADER Electronics  
or type ADS-24NP-12-1 12024G,manufactured by HONOR Electronic  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2050T  
50.8 cm (20.0 inches) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 50.8 cm  
0.2766 x 0.2766 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 - 83 kHz (Automatic)  
56 - 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
VESA 1600 x 900 @ 60 Hz  
VESA 1600 x 900 @ 60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B(Digital),DDC2AB(Anlaog)  
:
21 W(Typ.)  
1 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 49.28 cm (19.40 inches)  
Height 38.96 cm (15.34 inches)  
Depth 19.80 cm ( 7.80 inches)  
Width 49.28 cm (19.40 inches)  
Height 31.66 cm (12.46 inches)  
Depth 3.99 cm ( 1.57 inches)  
Weight(excl. packing)  
2.6 kg (5.73 lbs)  
Tilt : -5˚ - 15˚  
Range  
12V  
2.0A  
Power Input  
AC-DC Adapter  
Type ADS-24S-12 1224G*,manufactured by HONOR Electronic  
or type MU24-B120200-xx,manufactured by LEADER Electronics  
or type ADS-24NP-12-1 12024G,manufactured by HONOR Electronic  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2250T  
54.6 cm (21.5 inches) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 54.6 cm  
0.248 x 0.248 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 - 83 kHz (Automatic)  
56 - 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
VESA 1920 x 1080 @60 Hz  
VESA 1920 x 1080 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B(Digital),DDC2AB(Anlaog)  
:
23 W(Typ.)  
1 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 52.58 cm (20.70 inches)  
Height 40.83 cm (16.07 inches)  
Depth 19.80 cm ( 7.80 inches)  
Width 52.58 cm (20.70 inches)  
Height 33.48 cm (13.18 inches)  
Depth 3.99 cm ( 1.57 inches)  
Weight(excl. packing)  
2.8 kg (6.17 lbs)  
Tilt : -5˚ - 15˚  
Range  
12V  
3.0A  
Power Input  
AC-DC Adapter  
Type FSP036-DGAA1,manufactured by FSP Group  
or type LCAP07F,manufactured by Lienchange Electronics  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2350T  
58.4 cm (23.0 inches) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 58.4 cm  
0.265 x 0.265 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 - 83 kHz (Automatic)  
56 - 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
VESA 1920 x 1080 @60 Hz  
VESA 1920 x 1080 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B(Digital),DDC2AB(Anlaog)  
:
28 W(Typ.)  
1 W  
0.5 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 55.98 cm (22.04 inches)  
Height 42.81 cm (16.85 inches)  
Depth 19.80 cm ( 7.80 inches)  
Width 55.98 cm (22.04 inches)  
Height 35.45 cm (13.96 inches)  
Depth 3.99 cm ( 1.57 inches)  
Weight(excl. packing)  
3.3 kg (7.28 lbs)  
Tilt : -5˚ - 15˚  
Range  
12V  
3.0A  
Power Input  
AC-DC Adapter  
Type FSP036-DGAA1,manufactured by FSP Group  
or type LCAP07F,manufactured by Lienchange Electronics  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Wall-outlet type  
Stand Base  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Preset Modes (Resolution)  
E1950T  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
49.725  
48.363  
60.123  
47.712  
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1360 x 768  
70  
60  
75  
60  
75  
75  
60  
75  
60  
3
4
5
6
7
8
*9  
*Recommend Mode  
E2050T  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
60.000  
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1152 x 864  
1600 x 900  
70  
60  
75  
60  
75  
60  
75  
75  
60  
3
4
5
6
7
8
*9  
*Recommend Mode  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2250T/E2350T  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
63.981  
79.976  
65.290  
67.500  
720 x 400  
640 x 480  
70  
60  
75  
60  
75  
60  
75  
75  
60  
75  
60  
60  
3
640 x 480  
4
800 x 600  
800 x 600  
5
6
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 1024  
1280 x 1024  
1680 x 1050  
1920 x 1080  
7
8
9
10  
11  
*12  
*Recommend Mode  
Indicator  
LED Color  
MODE  
On Mode  
Sleep Mode  
Off Mode  
Purple (front view)  
Purple Blinking (front view)  
Off  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Digitally yours  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Krell Industries Stereo Amplifier KAV 500 User Manual
Laser MP3 Player MP3 A9 4GB User Manual
Lennox International Inc Air Conditioner CONDENSING UNITS User Manual
LG Electronics Cell Phone 9250 User Manual
LG Electronics Flat Panel Television 19 22 26 32LD3 User Manual
LG Electronics Refrigerator LRFD21855 User Manual
Linksys Switch EG005W User Manual
Mabe Canada Dishwasher GHDA300 User Manual
Makita Power Hammer HR2800 User Manual
Maytag Clothes Dryer MGD5600TQ0 User Manual