LG Electronics Car Satellite TV System 32LT770H User Manual

32LT770H

37LT770H

42LT770H

47LT770H

Lodging Guest Interactive Pro:Centric TVs

Commercial Mode Setup Guide

Note: Selected features shown in this guide may not be available on all models.

EXPERIENCED INSTALLER

Automated Installation Routine Wizard

pages 11 – 14

Custom Master TV Setup

pages 15 – 18

Cloning Information

pages 29 – 37

FTG Mode of Operation

pages 38 – 39

P/N: 206-4214 (Rev B)

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

17. Power Cord

Caution: It is recommended that appliances be placed

2. Keep these instructions.

3. Heed all warnings.

upon a dedicated circuit; that is, a single outlet circuit

which powers only that appliance and has no additional

outlets or branch circuits. Check the TV specifications to

be certain.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

Periodically examine the cord of your appliance, and if its

appearance indicates damage or deterioration, unplug it,

discontinue use of the appliance, and have the cord replaced

with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse,

such as twisting, kinking, or pinching or being closed in a

door or walked upon. Pay particular attention to plugs, wall

outlets, and the point where the cord exits the appliance.

7. Do not block any ventilation openings. Install in accor-

dance with the manufacturer’s instructions.

8. Do not install near any heat sources, such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

Do not use a damaged or loose power cord. Be sure to grasp

the plug when unplugging the power cord. Do not pull on the

power cord to unplug the TV.

18. Overloading

Do not connect too many appliances to the same AC power

outlet as this could result in fire or electric shock. Do not

overload wall outlets. Overloaded wall outlets, loose or

damaged wall outlets, extension cords, frayed power cords,

or damaged or cracked wire insulation are dangerous. Any of

these conditions could result in ﬁre or electric shock.

10. Protect the power cord from being walked on or pinched,

particularly at plugs, convenience receptacles, and the

point where it exits from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

19. Outdoor Use/Wet Location

Warning: To reduce the risk of ﬁre or electrical

shock, do not expose this product to rain,

moisture or other liquids.

12. Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination in order to avoid injury from

tip-over.

Do not touch the TV with wet hands. Do not install this product

near ﬂammable objects such as gasoline or candles or expose

the TV to direct air conditioning.

Do not expose to dripping or splashing and do not place

objects ﬁlled with liquids, such as vases, cups, etc., on or over

the apparatus (e.g., on shelves above the unit).

PORTABLE CART WARNING

20. Grounding

Ensure that you connect the earth ground wire to prevent

possible electric shock (i.e., a TV with a three-prong grounded

AC plug must be connected to a three-prong grounded AC

outlet). If grounding methods are not possible, have a qualiﬁed

electrician install a separate circuit breaker. Do not try to

ground the unit by connecting it to telephone wires, lightning

rods, or gas pipes.

13. Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

21. Disconnect Device

14. Never touch this apparatus or antenna during a thunder or

The mains plug is the disconnecting device. The plug must

remain readily operable.

lightning storm.

15. When mounting a TV on the wall, make sure not to install

the TV by the hanging power and signal cables on the back

of the TV.

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn off

this unit by SWITCH.

16. Do not allow an impact shock or any objects to fall into the

(Continued on next page)

product, and do not drop objects onto the screen.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

26. Do not touch the ventilation openings, as they may become

(Continued from previous page)

hot while the TV is operating.

22. Outdoor Antenna Grounding

27. If you smell smoke or other odors coming from the TV or

hear strange sounds, unplug the power cord, and contact an

authorized service center.

If an outside antenna or cable system is connected to the

product, follow the precautions below.

An outdoor antenna system should not be located in the

vicinity of overhead power lines or other electric light or power

circuits or where it can come into contact with such power

lines or circuits as death or serious injury can occur.

28. Do not press against the front panel of the TV with your

hand or a sharp object (e.g., a nail, pencil, or pen) or make a

scratch on it.

29. Keep the product away from direct sunlight.

Be sure the antenna system is grounded so as to provide

some protection against voltage surges and built-up static

charges.

30. Dot Defect

The LCD panel is a high technology product with resolution

of two million to six million pixels. In a very few cases, you

could see ﬁne dots on the screen while you are viewing the

TV. Those dots are deactivated pixels and do not affect the

performance and reliability of the TV.

Article 810 of the National Electrical Code (NEC) in the U.S.A.

provides information with respect to proper grounding of the

mast and supporting structure, grounding of the lead-in wire

to an antenna-discharge unit, size of grounding conductors,

location of antenna-discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

31. Generated Sound

“Cracking”: A cracking noise that occurs while the TV is

On or when it is turned Off is generated by plastic thermal

contraction due to temperature and humidity. This noise is

common for products where thermal deformation is required.

Antenna Grounding According to NEC, ANSI/NFPA 70

Electrical circuit humming/panel buzzing: A low level noise is

generated from a high-speed switching circuit, which supplies

a large amount of current to operate a product. It varies

depending on the product. This generated sound does not

affect the performance and reliability of the product.

Ground Clamp

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

32. For LCD TV

Grounding Conductor

If the TV feels cold to the touch, there may be a small “ﬂicker”

when it is turned On. This is normal; there is nothing wrong

with the TV. Some minute dot defects may be visible on the

screen, appearing as tiny red, green, or blue spots. However,

they have no adverse effect on the TV’s performance. Avoid

touching the LCD screen or holding your ﬁnger(s) against it for

long periods of time. Doing so may produce some temporary

distortion effects on the screen.

(NEC Section 810-21)

Electric Service

Equipment

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

23. Cleaning

When cleaning, unplug the power cord and wipe gently with

a soft cloth to prevent scratching. Do not spray water or other

liquids directly on the TV as electric shock may occur. Do not

clean with chemicals such as alcohol, thinners or benzene.

24. Transporting Product

Make sure the TV is turned Off and unplugged and that all

cables have been removed. It may take two or more people

to carry larger TVs. Do not press against or put stress on the

front panel of the TV during transport.

25. Ventilation

Install the TV where there is proper ventilation. Do not install

in a conﬁned space such as a bookcase. Do not cover the TV

with cloth or other materials (e.g., plastic) while it is plugged

in. Do not install in excessively dusty places.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . .3

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Commercial Mode Overview . . . . . . . . . . . . . . . . . . . . . . . .6

Teaching FTG Configuration to a TV . . . . . . . . . . . . . . . . . . 42

Learning FTG Configuration from a TV . . . . . . . . . . . . . . . . 43

Optional Manual Configuration / TV Setup. . . . . . . . . . . . . . 44

–

FTG File Manager Utilities Overview. . . . . . . . . . . . . . . 45

–

Setup Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Pass-through Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

FTG Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Remote Management in FTG Mode. . . . . . . . . . . . . . . . . . . . 8

FTG File Manager Main Screen. . . . . . . . . . . . . . . . . . . . . . 45

FTG Channel Map Configuration Utility . . . . . . . . . . . . . . . . 46

FTG Channel Map Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

FTG Installer Menu Configuration Utility. . . . . . . . . . . . . . . . 48

Pro:Centric Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

–

IP Environment Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 49

–

Pro:Centric TV Interactive Menu Features . . . . . . . . . . . . . . . 9

Pro:Centric Interactive Menu Navigation . . . . . . . . . . . . . . . . 9

Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Accessing the IP Environment Menu . . . . . . . . . . . . . . . . . . 49

Configuring the Network Connection . . . . . . . . . . . . . . . . . . 49

Network Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

IP Stream Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Wake On LAN Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Media Share Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Remote Jack Pack / TV Connections & Setup . . . . . . . . . . 56

Automated Installation Routine Wizard . . . . . . . . . . . . . 11 14

–

Pro:Centric Auto Configuration. . . . . . . . . . . . . . . . . . . . . . . 12

Pro:Centric Manual Configuration. . . . . . . . . . . . . . . . . . . . . 12

USB Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Custom Master TV Setup. . . . . . . . . . . . . . . . . . . . . . . . 15 18

–

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cloning Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Clonable TV Setup Menu Features . . . . . . . . . . . . . . . . . . . 15

Custom Master TV Setup Procedure . . . . . . . . . . . . . . . . . . 16

References

Upgrading TV/PTC Software using a USB Memory Device . . . 57

Downloading a Splash Screen using a USB Memory Device . . 58

Power Consumption Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 59

TV Aux Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

b-LAN Setup & Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

FTG Mode via EBL (Local Configuration) . . . . . . . . . . . . . . . . 62

RJP Model List & Input Auto-sensing Hierarchy . . . . . . . . . . . 63

Restoring Factory Defaults on the TV(s) . . . . . . . . . . . . . . . . . 64

TV Zone Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Wi-Fi Screen Share . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

LT770H Rear and Side Jack Panels . . . . . . . . . . . . . . . . . . . . 67

External Speaker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Installer Remote Control Typical Key Functions . . . . . . . . . . . 69

Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 27

–

Accessing the Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . 19

Using the Installer Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Exiting the Installer Menu and Activating Updates. . . . . . . . 20

Channel Icons/Custom Text Labels (2-5-4+MENU Mode). . 28

Cloning Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

USB Cloning Procedures. . . . . . . . . . . . . . . . . . . . . . . . .30 33

–

Learning / Teaching a Master TV Setup using

a USB Memory Device / .tlx File. . . . . . . . . . . . . . . . . . . . . . 30

Learning / Teaching a Master TV Setup using

a USB Memory Device / .tll File . . . . . . . . . . . . . . . . . . . . . . 32

Clone Programmer Cloning Procedures . . . . . . . . . . . .34 37

–

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 0– 73

General Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . 71

Commercial Mode Check / FTG Operation Troubleshooting . 72

Clone Programmer Troubleshooting. . . . . . . . . . . . . . . . . . . 73

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Learning / Teaching a Master TV Setup using

a TLL-1100A Clone Programmer . . . . . . . . . . . . . . . . . . . . . 34

Learning / Teaching a Master TV Setup using

an LT2002 Clone Programmer . . . . . . . . . . . . . . . . . . . . . . . 36

FTG Mode of Operation Overview . . . . . . . . . . . . . . . . .38 39

–

FTG Mode via CPU or EBL . . . . . . . . . . . . . . . . . . . . . . . . . 38

Determining the TV Operating Mode . . . . . . . . . . . . . . . . . . 39

Document Revision History / Open Source Software Notice . . . 75

Back Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

FTG Mode via CPU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 44

–

Creating an FTG Configuration File using the

FTG File Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Notes

• Installer Menu content is intended for use primarily by qualiﬁed TV electronics technicians.

• Refer to the Quick Reference Guide for additional information on TV installation, features, speciﬁcations, maintenance, and safety instructions.

• Design and speciﬁcations subject to change without prior notice.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Commercial Mode Overview

This document describes how to set up LT770H Pro:Centric TVs for Commercial Mode operation.

LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map

resides in the TV’s CPU, Protocol Translator Card (PTC), or embedded b-LAN™ (EBL) module, or it

resides externally from the TV (i.e., in a device from the solution provider).

These TV models are capable of Free-To-Guest (FTG) Mode operation via the TV CPU. Alternatively, the

EBL module can be configured either for Pass-through Mode (default) or FTG Mode. When neither the CPU

nor EBL is in FTG Mode, these TV models also allow external control via the TV’s MPI port.

Setup Checklist

Note: This document provides information specific to Commercial Mode operation. Refer to the Quick

Reference Guide for information on TV installation and hardware and cable connections.

Installation

Cable Connections

__ Unpack TV and all accessories.

__ Install batteries in the Installer Remote.

__ Install TV on VESA mount or stand.

Note: It may be advisable to make all cable

connections before installing on VESA mount

or stand, as appropriate.

__ Make all rear jack panel and MPI card slot

connections, as appropriate.

Commercial Mode Setup

__ Complete appropriate procedures as described

in this document for Commercial Mode operation.

Hardware Connections

__ Install any additional hardware as

appropriate to your institution, LAN, etc.

Pass-through Mode

This mode allows you to configure individual TVs for Pro:Centric or FTG Mode via CPU operation and/

or create a Master TV Setup for cloning purposes for TVs that are to remain in Pass-through Mode. This

mode also allows external control via the GAME CONTROL/MPI port on the TV rear jack panel.

There are two methods for configuring individual TVs that are currently in Pass-through Mode: either

using the Automated Installation Routine Wizard or the Custom Master TV Setup procedure as described

in this document.

Automated Installation Routine Wizard

The Automated Installation Routine Wizard provides Auto or Manual options for conﬁguring essential

items for Pro:Centric operation and also provides an option for using a USB memory device to conﬁgure

the TV for FTG Mode via CPU. Use the Installer Remote to make selections and complete each step. See

“Automated Installation Routine Wizard” on pages 11 to 14 for detailed information.

Custom Master TV Setup

The Custom Master TV Setup procedure enables you to create a customized Master TV Setup for cloning

purposes. Use the Installer Remote to conﬁgure Installer Menu items as required for TV operation and

set up TV features (Channel, Picture, Audio, etc.). See “Custom Master TV Setup” on pages 15 to 18 for

detailed information.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Commercial Mode Overview (Cont.)

Installer Menu

To create a Master TV Setup, you will need to know how

to access the commercial controller (PTC) Installer Menu

and make changes to the default values as required. If

necessary, familiarize yourself with the Installer Menu and

how to make and save changes. Refer to pages 19 to 27

for information on accessing the Installer Menu and for

detailed descriptions of the Installer Menu items.

xxLT770H PTC INSTALLER MENU

CPU-CTV

000 INSTALLER SEQ

000

UPN 000-000-000-000

PTC V1.00.009

ASIC D279

CPU V3.04.00

TV Setup Menus

On-screen setup menus control the features of the TV.

Use the Installer Remote to access the TV setup menus,

and set the TV features to the desired configuration for

the end user.

Typical Installer Menu

Cloning

Cloning refers to the process of capturing a Master TV

Setup and transferring it to a Target TV. Both TVs must

be in Pass-through Mode and both TVs must be identical

models. The Master TV’s clonable setup menu features

should be configured as part of the Master TV Setup. If

there are features in the Master TV’s setup—channel

icons or labels, digital font options, etc.—that are not set

or that are set incorrectly, those features also will not be

set or will be set incorrectly in the Target TVs. Refer to

pages 29 to 37 for detailed information on cloning

requirements and procedures.

PICTURE

LOCK

TIME

AUDIO

CHANNEL

OPTION

INPUT

SmartShare

TV Setup Menus

External MPI Control

To control the TV using an external MPI control device, you must use

the TV’s GAME CONTROL/MPI port for communication purposes. In

these TVs, Installer Menu item 118 POWER SAVINGS controls the

power circuitry for both the embedded b-LAN module and the GAME

CONTROL/MPI port; therefore, to ensure that the GAME CONTROL/

MPI port circuitry is powered, thus enabling MPI communication,

Installer Menu item 118 POWER SAVINGS must be set appropriately.

See Installer Menu item descriptions as well as Reference section,

“b-LAN Setup & Overview,” for further information.

Note: These TV models are not equipped with MPI card slots.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Commercial Mode Overview (Cont.)

FTG Mode

This mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels

to remove the need for dash tuning. TV operation in FTG Mode is based on which element of the TV owns

the FTG Logical Channel Map—the CPU or the EBL. Understanding the application in which the TV will be

used is vital in determining the owner.

As indicated above, FTG mode operation in the LT770H models can be provided either by the TV CPU

or the EBL. These are two separate and distinct FTG Modes of operation, each with its own unique

advantages and requirements as described later in this document. When the TV CPU is configured with

an FTG Channel Map, the CPU controls the operation of the TV, and when the EBL is configured with an

FTG Channel Map, the EBL controls the operation of the TV.

Once it is determined whether the TV CPU or the EBL will own the FTG Channel Map, conﬁguration can

begin. Conﬁguration of either requires a PC application—the LG FTG File Manager for the TV CPU or the

LG FTG Device Conﬁguration Application for the EBL. Each application provides utilities that enable you

to create/edit an FTG Channel Map and conﬁgure Installer Menu settings. See “FTG Mode of Operation

Overview” on pages 38 and 39 for further information on FTG Mode operation and conﬁguration.

Remote Management in FTG Mode

When the TV is configured for FTG Mode via CPU, remote management of the FTG Channel Map and

FTG Installer Menu settings is provided by a Pro:Centric server. Refer to the Pro:Centric Server Admin

Client User Guide for further information.

When the TV is configured for FTG Mode via EBL, the b-LAN module, which is internal to the TV, allows

hotel/institution head end equipment (for example, an FMA-LG101) with b-LAN technology to communicate

with the TV to provide remote management of the FTG Channel Map and FTG Installer Menu settings. See

Reference section, “b-LAN Setup & Overview,” for further information.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Pro:Centric Operation

Pro:Centric TV Interactive Menu Features

When running the Pro:Centric application, the interactive Pro:Centric TV enables guests to locate and

select television entertainment using an interactive channel guide, check the daily weather, and view hotel

and surrounding amenities via custom billboards and points-of-interest maps.

Pro:Centric application features include:

• Portal and information screens/pages (including a “Welcome” page) that include branding logos.

• An optional customized user interface (custom “skins”).

• Billboards and points-of-interest maps that can be customized to focus on hotel amenities, local attractions

and businesses, restaurants, news, events, etc.

• An optional Weather billboard that includes a local radar map, current conditions, and a four day forecast.

• An interactive channel guide that provides a channel list with channel icons. An electronic program

guide (EPG) is an optional feature that displays up to three days of programming information viewable

by channel and time.

• Video spooling that enables the hotel to deliver a video ﬁle to guest TVs for promotion and information

purposes.

The Pro:Centric server Admin Client web editor/content wizard is provided for customer conﬁguration of

portal messages and billboards/maps.

Note: Customized content is typically deﬁned by the service integrator and/or hotel administrators. LG

does not provide hotel-speciﬁc content.

Pro:Centric Interactive Menu Navigation

Use the Pro:Centric TV remote control to operate both interactive menus and regular TV features. Press

PORTAL on the remote to access the interactive menus.

Note: Interactive menu options may vary, depending on Pro:Centric features enabled for the site. The

following are default interactive menus.

Channel Guide

Shows available TV networks and logical channels. When available, EPG

data provides additional channel and program information.

Information

Typically displays information on hotel amenities, for example, restaurants,

in-room dining, business centers, facilities, etc., as well as information on

local weather and attractions.

Help

Provides help for navigating the interactive menus.

Watch TV

Removes the interactive menu from the screen and returns to the previously

tuned TV channel.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Pro:Centric Operation (Cont.)

Pro:Centric Setup

Administration and management options for the Pro:Centric server are described in detail in the

Pro:Centric Server Admin Client User Guide. This document describes only those settings that must be

speciﬁed on the TVs.

On the TVs, the Pro:Centric server settings must be conﬁgured appropriately to enable Pro:Centric remote

management/administration facilities, while the Pro:Centric Application Mode must be set appropriately to

enable the Pro:Centric application.

• Remote management/administration (TV E-Z Installation): The Pro:Centric server Admin Client provides

remote management/administration facilities for downloading splash screens and software/firmware

updates as well as facilities for downloading the FTG Channel Map and FTG Installer Menu settings for

TVs that are in FTG Mode via CPU.

• Pro:Centric application: The application, which operates in conjunction with FTG and PPV Modes,

comprises the Pro:Centric interactive menus/features described on the previous page. Pro:Centric

application settings are managed via the Pro:Centric Admin Client.

The Pro:Centric server settings can be conﬁgured using one of the following methods:

• When the TV is in a factory default state, the Automated Installation Routine Wizard provides Auto or

Manual options for conﬁguring the Pro:Centric server settings.

The Automated Installation Routine Wizard also provides a USB Conﬁguration option that enables you

to conﬁgure a TV for FTG Mode via CPU using an FTG Conﬁguration (.tlx) ﬁle stored on a USB memory

device. The FTG Conﬁguration ﬁle incorporates FTG Installer Menu settings, which includes Installer

Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL.

Refer to “Automated Installation Routine Wizard” on pages 11 to 14 for further information on the

Automated Installation Routine Wizard options.

• If the TV is in Pass-through Mode, either:

− Set Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL to the appropriate values.

Refer to “Installer Menu” information on pages 19 to 27 for further information. Also, as necessary,

refer to “Custom Master TV Setup” information on pages 15 to 18 and/or cloning information on pages

29 to 37.

− Conﬁgure the appropriate Pro:Centric server settings in the IP Environment / Pro:Centric Menu. See

“Accessing the IP Environment Menu” on page 49 and “Pro:Centric Setup” on page 53 for further

information.

• If the TV is in FTG Mode (via CPU or EBL), use the appropriate software to update the Data Channel and

Pro:Centric Installer Menu items (along with their afﬁliated ﬁelds) and then transfer the FTG Installer Menu

settings to the TV in accordance with the FTG Mode of conﬁguration. Refer to “FTG Mode of Operation

Overview” on pages 38 and 39 for further information on FTG Mode operation and conﬁguration.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Automated Installation Routine Wizard

The Automated Installation Routine Wizard will appear on the screen each time the TV is turned ON, until

one of its conﬁguration methods has been completed or the wizard is exited.

The wizard’s Welcome screen provides a selection of conﬁguration methods: Auto or Manual options for

conﬁguring essential items for Pro:Centric operation and also an option for using a USB memory device

to conﬁgure the TV for FTG Mode via CPU. This section describes each of the Automated Installation

Routine Wizard options.

Move

Welcome

Please select configuration method.

Pro:Centric Auto

Pro:Centric Manual

USB Configuration

Exit

Before you begin, note the following:

• If it has been completed or exited and therefore does not display, the Automated Installation Routine

Wizard can be re-activated; however, this requires that factory defaults be restored on the TV(s). Refer

to Reference section, “Restoring Factory Defaults on the TV(s),” for further information.

• If you plan to create a Master TV Setup using the procedure described on pages 15 to 18, be sure to

exit the Automated Installation Routine Wizard in order to avoid setting modes that may restrict the

custom setup procedure.

• If any of the conﬁguration steps fails, you will see an “Incomplete” screen with an indication of the

failure. You will then have the opportunity to reinitiate the current conﬁguration process, select another

conﬁguration method (for example, to select Pro:Centric “Manual” instead of “Auto” conﬁguration), or

exit the Automated Installation Routine Wizard.

• If you wish to enable media sharing (i.e., Smart Share and Wi-Fi Screen Share) on the TV, you will need

to create a custom Master TV Setup and use the IP Environment Menu to specify the settings. Custom

Master TV Setup is described on pages 15 to 18. Refer to “IP Environment Setup” on pages 49 to 55 for

information on the IP Environment Menu.

• If you need to specify a zone restriction for the TV, you will need to create a custom Master TV Setup

as described on pages 15 to 18 and specify this setting in the TV setup menus. See also Reference

section, “TV Zone Restrictions,” for further information. Note that the zone restriction is not clonable.

Caution: Do NOT unplug the TV power cord or remove the antenna cable during any of the

conﬁguration processes, as doing so will interrupt the current step and may corrupt the

conﬁguration data.

To exit the Automated Installation Routine Wizard, use the Up/Down arrow keys on the Installer

Remote to select/highlight Exit. Then, press OK.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Automated Installation Routine Wizard (Cont.)

Pro:Centric Auto Conﬁguration

When selected, this option enables the TV to use a search algorithm to automatically determine

the type of Pro:Centric network, the (RF) Data Channel, and the Pro:Centric Application Mode.

The TV then looks for the Pro:Centric application and maintenance (E-Z Installation) ﬁles to

download.

Note: If the Pro:Centric server conﬁguration is IP or if you intend to use the Pro:Centric server for

remote management only of TV E-Z Installation (splash screen, configuration, and/or firmware)

data downloads, use the “Pro:Centric Manual” option described below.

Use the Up/Down arrow keys on the Installer Remote to select/

highlight Pro:Centric Auto from the Automated Installation

Routine Wizard Welcome screen. Then, press OK.

Prev.

Auto Configuration

Processing Pro:Centric Configuration.

Step 2 may take up to 15 min(s).

Please wait...

The Pro:Centric Auto Conﬁguration will proceed with a series of

automated steps to conﬁgure the TV for Pro:Centric operation

and to download the Pro:Centric application and E-Z Installation

data. The Auto Conﬁguration screen (see example at right)

shows overall progress, as well as the progress and/or values

for each of the individual installation steps. Note that some steps

may require up to 15 minutes.

10%

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Detecting the type of Pro:Centric network

Locating the Pro:Centric Server

Determining the Pro:Centric mode

Downloading the application files

Downloading the maintenance files

Saving the Pro:Centric configuration

In Progress

Warning - Do not remove AC power or the signal cables during these steps

When the Pro:Centric Auto Conﬁguration is complete, the wizard

exits, and the TV will turn OFF.

Pro:Centric Manual Conﬁguration

If the Pro:Centric server conﬁguration is RF, and you already know the settings (i.e., Data Channel

and Pro:Centric Application Mode) that need to be conﬁgured in order for the TV to connect to the

Pro:Centric server, you may streamline the setup process by entering this data manually. Also, if

the Pro:Centric server conﬁguration is IP or if the Pro:Centric server is to be used solely for remote

management of E-Z Installation data downloads, this procedure enables you to specify the appro-

priate settings.

1. Use the Up/Down arrow keys on the Installer Remote to select/highlight Pro:Centric Manual

from the Automated Installation Routine Wizard Welcome screen. Then, press OK.

In the ﬁrst Manual Conﬁguration Screen (see examples on following page), you will be able to

conﬁgure the appropriate Pro:Centric settings. Use the Up/Down arrow keys on the Installer

Remote to navigate between ﬁelds.

Note: Select the “Back” button from the Manual Conﬁguration screen or press the key on the

Installer Remote, if desired, to return to the Welcome screen.

2. In the Pro:Centric Mode ﬁeld, use the Left/Right arrow keys to select the appropriate

Pro:Centric Application Mode—GEM, FLASH, HTML, or Conﬁguration Only.

Note: For remote management only, select the Pro:Centric Mode “Conﬁguration Only”

option to only search for TV E-Z Installation data downloads. Pro:Centric application data will

not be downloaded.

3. Refer to the appropriate subsection on the next page, depending on the Pro:Centric server

conﬁguration, to complete the remaining ﬁelds.

(Continued on next page)

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Automated Installation Routine Wizard (Cont.)

(Continued from previous page)

RF Conﬁguration

Move

Prev.

Manual Configuration

Pro:Centric Mode

a) In the Media Type ﬁeld, use the Left/Right arrow keys to

GEM

select RF.

Media Type

Data Channel

Signal Strength

b) In the Data Channel ﬁeld, either key in or use the Left/Right

arrow keys to select the RF channel number for the Data

Channel of the Pro:Centric server. The Data Channel can

be set from 1 to 135.

No signal

Back

Save and Exit

IP Conﬁguration

a) In the Media Type ﬁeld, use the Left/Right arrow keys to

Manual Conﬁguration Screen with

RF Media Fields

select IP.

Note: By default, the initial Manual Conﬁguration screen

shows RF conﬁguration ﬁelds. When you select “IP” as

the Media Type, the Data Channel and Signal Strength

ﬁelds are replaced with (IP) Address and Port ﬁelds.

Move

Prev.

Manual Configuration

Pro:Centric Mode

GEM

Media Type

Address

Port

b) In the Address and Port ﬁelds, either key in or use the

Left/Right arrow keys to select the appropriate values for

the Pro:Centric server IP address and port number.

255

The IP address must match the IPv4 multicast address

and the port number must match the port number that is

set in the Pro:Centric server.

Back

Save and Exit

4. Once all ﬁelds are completed as required, you may have two

options (see also note below):

Manual Conﬁguration Screen with

IP Media Fields

• To save the data entered and exit the wizard, use the arrow

keys to select Save and Exit, and then press OK. The

Pro:Centric application and/or E-Z Installation data will be

downloaded to the TV at a later time. This option is useful,

in particular, if the Pro:Centric server has not yet been

conﬁgured.

Prev.

Manual Configuration

• To initiate a real-time download of Pro:Centric application

and/or E-Z Installation data, use the arrow keys to select

Next, and then press OK.

Processing Pro:Centric Configuration.

Step 4 may take up to 5 min(s).

Please wait...

The Pro:Centric Manual Conﬁguration will proceed with the

remaining Pro:Centric application and/or E-Z Installation

data download steps, as shown on the second Manual

Conﬁguration screen (see example at right). When the

Pro:Centric Manual Conﬁguration is complete, the wizard

exits, and the TV will turn OFF.

50%

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Detecting the type of Pro:Centric network

Locating the Pro:Centric Server

Determining the Pro:Centric mode

Downloading the application files

Downloading the maintenance files

Saving the Pro:Centric configuration

DIGITAL 75

GEM

In Progress

Warning - Do not remove AC power or the signal cables during these steps

Note: If Media Type is set to “RF,” the RF signal must be

present on the Data Channel of the Pro:Centric server in order

for you to select “Next” (you will see a “Data Channel found”

message below the signal strength indicator). If Media Type is

set to “IP,” there must be a LAN cable connected between the

TV and the network in order for you to select “Next.”

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Automated Installation Routine Wizard (Cont.)

USB Conﬁguration

This section describes how to conﬁgure a TV for FTG Mode via CPU operation using an FTG

Conﬁguration (.tlx) ﬁle loaded on a USB memory device.

Note: Refer to the Free-To-Guest (FTG) File Manager User Guide and/or “Creating an FTG

Conﬁguration File using the FTG File Manager” on pages 40 to 41 for information on creating an

FTG Conﬁguration (.tlx) ﬁle.

Note: This procedure assumes that the FTG Conﬁguration ﬁle contains an FTG Channel Map. If

not, any Installer Menu and/or TV setup menu settings contained in the ﬁle will be transferred to

the TV (as with typical cloning); however, the TV will remain in Pass-through Mode and will not

be conﬁgured for FTG Mode via CPU.

1. Plug the USB memory device that contains the FTG

Conﬁguration (.tlx) ﬁle into the Target LT770H TV USB IN port.

Move

Prev.

Accessing USB Storage Device

2. Use the Up/Down arrow keys on the Installer Remote to

Please select configuration file (*.tlx)

select/highlight USB Conﬁguration from the Automated

Installation Routine Wizard Welcome screen. Then, press OK.

xxLT770H-UA00001.TLX

3. In the Accessing USB Storage Device window, use the Up/

Down arrow keys to select the FTG Conﬁguration ﬁle you

wish to use to conﬁgure this TV, and then press OK.

The TV will show conﬁguration progress in a new window.

Do NOT remove the USB device until conﬁguration is

complete. When the conﬁguration is complete, the TV will

brieﬂy display a “Complete” window and then exit the

Automated Installation Routine Wizard.

USB Configuration

4. Remove the USB memory device, and verify that the FTG

Configuration is resident on the Target TV.

Configuring TV

The Target TV CPU is now in FTG Mode.

Please wait...

95%

Note: After the conﬁguration process is complete, the TV tunes

according to the Start Channel setting in the Installer Menu. If

a Start Channel is speciﬁed, the TV will tune to that channel;

otherwise, the TV will tune to the lowest logical channel in the

FTG Channel Map.

Warning - Do not remove the USB device during this process

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Master TV Setup

This section describes how to create a customized Master TV Setup for cloning purposes when the TV is

in Pass-through Mode.

Note: Refer to “FTG Mode of Operation Overview” on pages 38 and 39 for information on FTG Mode

operation and conﬁguration.

Note: Cloning requirements and procedures are described in detail on pages 29 to 37.

Cloning Methods

Before You Begin

See also “Clonable TV Setup Menu Features” list below.

• It is recommended that you disconnect all Aux

inputs if you intend to run Auto Tuning (Channel

Search). Under certain conditions, Auto Tuning

is disabled if there is an Aux input active.

Using a USB Memory Device / .tlx File

• The .tlx ﬁle format clones Installer Menu settings, IP Environment

settings (with the exception of network conﬁguration and Media

Share / TV Name settings—see pages 49 to 55), and all TV sources’

(analog, digital, AV1, HDMI, etc.) clonable setup menu settings.

• Determine which cloning tool—USB memory

device or clone programmer—is appropriate for

your application; several of the Master TV Setup

procedure steps are dependent on the cloning

tool to be used. See “Cloning Methods” at right

for further information.

• Not intended for cloning an auto-tuned/edited Channel Map, as the

channel lineup is converted to a logical FTG Channel Map when

saved (Learned) from a TV to a .tlx ﬁle. If the .tlx ﬁle with the FTG

Channel Map is then used for Teaching purposes, all Target TVs

will be conﬁgured for FTG Mode via CPU.

• If you intend to use a USB memory device,

determine the type of ﬁle—either the new “.tlx”

ﬁle format or the legacy “.tll” ﬁle format—to use

for cloning purposes; several of the Master TV

Setup procedure steps are dependent on the

desired ﬁle type. See “Cloning Methods” at right

for further information.

Using a USB Memory Device / .tll File

The .tll ﬁle format clones the contents of the commercial controller

(PTC) memory, including an auto-tuned/edited Channel Map,

Installer Menu settings, and one TV source’s (analog, digital, or Aux)

clonable setup menu settings.

• If the Automated Installation Routine Wizard

appears on the screen, exit the wizard before

beginning/continuing the Custom Master TV

Setup procedure.

Using a Clone Programmer (TLL-1100A or LT2002)

Both the TLL-1100A and LT2002 clone the contents of the

commercial controller (PTC) memory, including an auto-tuned/edited

Channel Map, Installer Menu settings, and one TV source’s (analog

or Aux) clonable setup menu settings.

Clonable TV Setup Menu Features

Channel

Audio

Auto Volume

Clear Voice

Sound Mode

Balance

Option

Auto Tuning (Channel Lineup)

Manual Tuning

Channel Edit

Menu Language

Audio Language

Caption

Channel Label

TV Speaker

Lock

Movie Rating

Picture

Picture Mode

Time

Auto Clock

Auto Off (Sleep Timer)

TV Rating – Children

TV Rating – General

Note: Some menu options vary between analog and digital channels and Aux inputs.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Master TV Setup (Cont.)

Custom Master TV Setup Procedure

1. Turn ON the TV.

If the Automated Installation Routine Wizard appears on the screen when you turn ON the

TV, use the Up/Down arrow keys on the Installer Remote to select Exit from the Welcome

screen, and press OK to exit the wizard.

2. Set Installer Menu items.

This step provides speciﬁc instruction only on the Installer Menu items

that should be set on a Master TV. Refer to pages 19 to 27 for detailed

xxLT770H PTC INSTALLER MENU

information on all Installer Menu items.

CPU-CTV

a) Use the Installer Remote to access the PTC Installer Menu (see

“Accessing the Installer Menu” on page 19 for further information).

000 INSTALLER SEQ

000

The next step depends on whether the Automated Installation

Routine Wizard appeared when you turned ON the TV:

UPN 000-000-000-000

PTC V1.00.009

ASIC D279

CPU V3.04.00

• If the wizard did appear, the TV is in a factory default state, and

you can proceed to set Installer Menu items. Go to step (c).

• If the wizard did not appear, go to step (b).

Typical Installer Menu

b) Set Installer Menu item 117 FACT DEFAULT to 001 and press

OK on the Installer Remote.

Note: The Installer Menu header will vary

depending on the TV you are setting up.

This clears all Installer Menu custom settings, channel lineup, etc.

and restores the factory default settings. The value will change

back to 0 after the PTC has been restored to factory default

condition. This step ensures that the TV Channel Memory will be

the active channel lineup.

117 FACT DEFAULT

003 BAND/AFC

000

001

c) Set Installer Menu item 003 BAND/AFC, as appropriate.

Adjust the values for these

Installer Menu items, as required.

• Broadcast: Set to 000.

• HRC: Set to 002.

• IRC: Set to 003.

• CATV: Set to 001 (default).

d) Set any other Installer Menu items that affect your TV programming

network to the required conﬁguration. For example, enable/disable

Aux inputs, set a Start Channel, etc.

Note: If you intend to use a USB memory device / .tlx ﬁle for

cloning purposes, you may also conﬁgure selected settings in the

IP Environment Menu (accessible from the Installer Menu). See

also “Cloning Methods” on the previous page and “IP Environment

Setup” on pages 49 to 55 for further information.

e) After you have adjusted all Installer Menu item settings as required,

press OK once on the Installer Remote to save your changes; then,

press OK again to exit the menu.

Note: If you performed step (b) above to restore factory defaults,

the Automated Installation Routine Wizard will re-activate as soon

as you exit the Installer Menu. Exit the wizard (see step 1), and

then continue with step 3.

(Continued on next page)

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Master TV Setup (Cont.)

(Continued from previous page)

3. Set up TV features.

On-screen setup menus control the features of the TV. Press MENU

SETTINGS on the Installer Remote to access the TV setup menus,

and then set Channel, Picture, Audio, Lock, Time, etc. options to the

desired configurations. See “Clonable TV Setup Menu Features” list on

page 15 and also notes below.

PICTURE

LOCK

TIME

AUDIO

CHANNEL

INPUT

Note: If you intend to clone the PTC, remember that only one TV

source’s clonable setup menu settings will be cloned. Thus, for a

clone programmer, the TV setup menu settings should be applicable

to either an analog channel or Aux input, while for a USB device / .tll

file, the TV setup menu settings should be applicable to the analog or

digital channel or Aux input to which the Target TV will be set during

the Teaching process.

OPTION

SmartShare

Use the TV setup menus to set the TV

features to the desired configuration

for the end user.

Note: If desired and if appropriate depending on the cloning method

to be used (see “Cloning Methods” on page 15), you can run Auto

Tuning (see step 4) prior to completing this step.

CHANNEL

Move

4. (Optional) Run Auto Tuning.

• Auto Tuning

Note: If you intend to use a USB memory device / .tlx file

for cloning purposes, DO NOT run Auto Tuning. If you

Teach a .tlx file with an auto-tuned/edited Channel Map to

a Target TV, this will put the Target TV in FTG Mode via

CPU. Proceed to step 7 to verify the TV setup. (Steps 5

and 6 are not applicable for .tlx files.)

• Manual Tuning

• Channel Edit

• Channel Label

If you run Auto Tuning with the intention to clone the resulting

Channel Map, you must use a USB memory device / .tll file or a

clone programmer for this cloning purpose.

(Optional) Use Channel Menu options

to run Auto Tuning, edit channels, and

select channel icons.

a) To search for all available analog and digital channels, go to the

Channel Menu, select the Auto Tuning option, and follow the

on-screen instructions.

b) Use the Channel Edit option in the Channel Menu to edit the channel lineup, as

necessary, to include only free to guest (non-encrypted) channels.

• Add/delete channels per your system requirements.

• Use the Channel Label option in the Channel Menu to select the appropriate

trademark/icon for each channel’s Channel-Time on-screen display. Icons are

available for familiar channels, such as ABC, CBS, NBC, etc. Identiﬁable labels

(icons) should enable the end user to readily know what common networks are

available.

Note: If you intend to clone the PTC and Installer Menu item 103 ATSC TUNE MODE

is set for Physical Channel tuning (default and recommended setting), channels with

minor channel numbers higher than 255 will not transfer correctly in step 5. If item 103

is set for Virtual Channel tuning and either the major or minor channel numbers are

higher than 255, the channel(s) will not transfer correctly in step 5.

Note: If you intend to clone the PTC, you can add the channel icons in this step or

as described in step 6. Also in step 6, you can add custom text labels for channels

without icons.

(Continued on next page)

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Master TV Setup (Cont.)

(Continued from previous page)

5. Transfer the TV setup menu settings to the commercial controller (PTC):

2-5-5 + MENU Mode

Note: This step is essential for successful cloning using a USB memory device /

.tll file or a clone programmer. Without this step, the PTC will not contain any of

the TV setup menu settings.

Note: The maximum number of channels (analog, digital, and Aux inputs) that can

be transferred to the PTC is 141. An attempt to transfer more than 141 channels of

any combination will result in a Channel Map of exactly 141 channels; any extra

channels will not be available in the PTC Channel Map. For example, if you enabled

three Aux inputs in the Installer Menu and Auto Tuning found 141 channels, you

must edit the Channel Map to decrease the number of analog/digital channels to (at

most) 138.

a) After the TV channel lineup has been edited and channel label icons added, tune to the

channel (source) for which you wish to transfer TV setup menu settings.

Note: If you intend to use a clone programmer for cloning purposes, this must be either

an analog channel or Aux input.

b) Access the Installer Menu, and press 2-5-5 + MENU SETTINGS on the Installer

Remote to initiate the transfer of the Master TV Setup to the PTC. The TV exits the

Installer Menu and then tunes through the channels in the channel lineup during the

transfer. When the transfer is complete, the TV tunes back to the channel that was

tuned before the transfer began.

6. (Optional) Add Custom Channel and Aux Input Labels:

2-5-4 + MENU Mode

Note: 2-5-4 + MENU Mode enables you to add/edit channel icons and

custom text labels in the PTC once the Master TV Setup has been

transferred as described in the previous step.

DIGITAL 19-3

MONO STEREO SAP

Access the Installer Menu, and press 2-5-4 + MENU SETTINGS on the

Installer Remote. Add/edit custom text labels and/or change icons for

the Channel-Time on-screen displays (see 2-5-4 + MENU procedural

information on page 28). Note that broadcast digital channels often

already have a broadcaster generated label. When you are finished,

press MENU SETTINGS to exit 2-5-4 + MENU Mode.

WXYZ

Custom text label “WXYZ” created

in 2-5-4 + MENU Mode.

7. Verify the TV setup.

As applicable, verify that the channel lineup, channel icons, and custom

text labels are correct. Also, make sure the TV features are set per your

requirements.

028 CH. OVERIDE

000

After verifying the TV Setup, set Installer

Menu item 028 CH. OVERIDE to 000.*

8. (Recommended) Lock the channel lineup.

Access the Installer Menu. Set item 028 CH. OVERIDE to 000 and

press OK to lock the channel lineup and restrict access to the TV

setup menus. Press OK again to save your changes and exit the

Installer Menu.*

* This step prevents end users from

accessing channel settings (i.e., the

Channel Menu will be inaccessible/

grayed out).

The Master TV Setup is now ready to be copied to the predetermined

cloning tool—a USB memory device (.tlx or .tll ﬁle) or a clone programmer.

See cloning procedures in this document.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Installer Menu

Use the Installer Menu to set up, change, or view operational settings. Refer to the table on pages

21 and 22 for brief descriptions of Installer Menu items. More detailed descriptions follow the table

listing.

Accessing the Installer Menu

1. Turn ON the TV.

If the Automated Installation Routine Wizard appears on the

screen when you turn ON the TV, use the Up/Down arrow keys

on the Installer Remote to select Exit from the Welcome screen,

xxLT770H PTC INSTALLER MENU

CPU-CTV

and press OK to exit the wizard.

2. Using an Installer Remote, press MENU SETTINGS repeatedly

until the on-screen display of the TV setup menus (if the TV is

in Pass-through Mode) or the Function Menu (if the TV is not in

Pass-through Mode) no longer toggles, and then press the

Installer Menu entry sequence (e.g., 9-8-7-6) + OK to access the

Installer Menu.

000 INSTALLER SEQ

000

UPN 000-000-000-000

PTC V1.00.009

ASIC D279

CPU V3.04.00

Note: The default Installer Menu entry sequence is “9876”;

however, if Installer Menu item 000 INSTALLER SEQUENCE

has been modiﬁed, the entry sequence may be one of three

additional options. See Installer Menu detailed descriptions for

further information.

Typical Installer Menu

The Installer Menu opens with item 000 INSTALLER SEQ 000.

Note: If the password (entry sequence) is not entered or registered correctly, you will see the

message “ENTER PASSWORD 0000” at the top of the screen instead of the Installer Menu

header. Once you re-enter the correct password (e.g., press 9-8-7-6 + OK), the Installer Menu will

display.

Note: If the TV is not in Pass-through Mode, the Installer Menu is accessible as read-only.

As part of the Installer Menu header, two 3-character acronyms are displayed to indicate the

TV’s current conﬁguration mode. The table below lists all possible mode identiﬁers for these TV

models.

Acronym

Description

CPU-CTV

CPU-FTG

EBL-FTG

EBL-LNT

MPI-EXT

PTC-CTV

Pass-through Mode with Channel Map in CPU

FTG Mode via CPU

FTG Mode via EBL

LodgeNet PPV Mode

External MPI Control

Pass-through Mode with Channel Map in PTC

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Installer Menu (Cont.)

Using the Installer Menu

Refer to the table starting on the next page for an overview of the available Installer Menu items,

including their item numbers, functions, value ranges, and default values.

Installer Menu items not relevant to these TV models are not present in the Installer Menu; therefore,

some numbers are missing. For example, item 006 will not appear. In addition, items that are

dependent on other Installer Menu item settings will not be initially accessible. For example, item 046

STRT AUX SRCE will not display in the Installer Menu unless item 004 STRT CHANNEL is set to 0.

Navigation within the Installer Menu

Use the Up/Down arrow keys on the Installer Remote to sequence through the available menu

items, or access an item directly by keying in the item number and then pressing MENU SETTINGS.

For example, to access the SLEEP TIMER option, which is item 015, press 0-1-5 + MENU.

Changing Installer Menu Settings

To change an Installer Menu item value, use the Left/Right arrow keys on the Installer Remote, or

enter a valid value directly. To save the new setting, press OK, or use the Up/Down arrow keys to

navigate to a new Installer Menu item if you have additional items to edit. Note that invalid values will

not be saved.

Exiting the Installer Menu and Activating Updates

After you have adjusted all required Installer Menu item settings, press OK once on the Installer

Remote to save your changes; then, press OK again to exit the Installer Menu. Any changes you

make will be stored in non-volatile memory.

Note: Each time you exit the Installer Menu in Pass-through Mode, all V-Chip (Parental Control)

settings in the TV are reset to their default values; that is, the Lock System, if previously enabled

from the Lock setup menu, will now be disabled, and the individual Parental Control settings will be

restored to default values.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Installer Menu (Cont.)

Installer Menu Items 000 through 075

Function

Value Range

Default Value

Brief Description of Function and Comments

Item

000

001

002

003

INSTALLER SEQ

POWER MANAGE

AC ON

0 ~ 3

0 ~ 7

0 / 1

Leave default set to 0.

Sets number of hours of no activity before automatic shutoff.

Set to 1 to enable Auto Turn ON when AC power is applied.

Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC

BAND/AFC

0 ~ 3

0 ~ 127, 253,

255

Channel tuned when TV is turned ON. (Set to 255 to tune to channel

tuned before TV turned OFF.)

004

005

007

STRT CHANNEL

CHAN LOCK

255

0 / 1

If set to 1, cannot tune from current channel.

Volume level when TV is turned ON. (Set to 255 to use volume level

before TV turned OFF.)

STRT VOLUME

0 ~ 63, 255

255

008

009

010

011

015

016

017

020

021

022

023

028

029

030

031

032

MIN VOLUME

MAX VOLUME

MUTE DISABLE

KEY DEFEAT

SLEEP TIMER

EN TIMER

0 ~ 63

0 / 1

Sets minimum allowable volume setting.

Sets maximum allowable volume setting.

Set to 1 to disable Mute Function.

0 / 1

Set to 1 to disable menu navigation keys on display panel.

Set to 1 to enable Sleep Timer.

0 / 1

Set to 1 to enable On/Off Timers.

ALARM

0 / 1

Set to 1 to enable Alarm.

FEATURE LEVEL

V-CHIP

0, 16 ~ 24

0 / 1

Determines an additional IR code scheme to which the TV will respond.

Set to 1 to enable V-Chip (Parental Control) functions.

Sets number of V-Chip blocking hours.

Set to 1 to retain caption setting set before TV turned OFF.

If set to 0, limits direct access to favorite channels.

Set to 1 to change MPI operation to OCV.

If set to 1, enables ACK feature of MPI.

Selects poll rate for MPI.

MAX BLK HRS

CAPTION LOCK

CH. OVERIDE

OLD OCV

0 ~ 99

0 / 1

ACK MASK

0 / 1

POLL RATE

20 ~ 169

186 ~ 227

207

TIMING PULSE

Sets baud rate for MPI.

Set to 0 to disable HDMI 1. Set to 1 enable HDMI 1. Set to 5 to enable HDMI 1

but disable Hot Plug Detect (HPD) circuit.

035

HDMI1 ENABLE

0, 1, 5

039

041

046

REAR AUX EN.

SIMPLINK EN

0 / 1

0 ~ 3

Set to 1 to enable display panel Video 1 input jack.

Determines the status of the SIMPLINK feature. (See detailed descriptions.)

Sets the starting Aux source (if item 004 STRT CHANNEL is set to 0).

STRT AUX SRCE

1, 3 ~ 5, 7, 255

Set to 1 for MPI Aux source to be reported as a channel number instead of

Channel 0.

047

AUX STATUS

0 / 1

053

069

070

071

DIS. CH-TIME

EN. CH-T COL.

FOR. CH-TIME

BCK. CH-TIME

0 / 1

0 ~ 7

Set to 1 to disable Channel-Time display.

Set to 1 to enable custom color for the Channel-Time display.

Chooses custom foreground color for the Channel-Time display.

Chooses custom background color for the Channel-Time display.

If set to 1 and item 028 CH. OVERIDE is set to 0, “NOT AVAILABLE” message

is displayed if user direct tunes a channel that is not in the favorite channel list.

073

075

CH NOT AVBLE

REVERT CH

0 / 1

If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Installer Menu (Cont.)

Installer Menu Items 078 through 122

Function

Value Range

Default Value

Brief Description of Function and Comments

Item

078

079

080

081

082

UPN MSB

0 ~ 255

0 / 1

User programmable number, most significant byte.

User programmable number, most significant byte - 1.

User programmable number, most significant byte - 2.

User programmable number, least significant byte.

Enforces rigid MPI checksum.

UPN MSB-1

UPN MSB-2

UPN LSB

CHKSM ERROR

Relaxes MPI timing to be compatible with PC-based Windows-

controlled systems.

083

084

087

HANDSHK TIME

PERMANENT BLK

REAR RGB EN.

0 ~ 5

0 / 1

Removes block hours setting for Parental Control and makes block permanent.

Dependent on item 093 RJP AVAILABLE setting. Set to 0 to disable RGB input.

Set to 1 to enable RGB input. Set to 17 for Auto Configure.

088

090

091

092

EN NOISE MUTE

KEY LOCK

0 / 1

If set to 1, audio is muted if no signal is present.

If set to 1, keyboard is locked out, IR is still functional.

Set to 0 to disable HDMI 2. Set to 1 to enable HDMI 2.

Set to 0 to disable HDMI 3. Set to 1 to enable HDMI 3.

HDMI2 ENABLE

HDMI3 ENABLE

Set to 0 to disable. Set to 1, 2, 5, or 6 for HDMI or DVI Mode. (See

detailed descriptions.)

093

RJP AVAILABLE

0, 1, 2, 5, 6

Set to 0 to disable feature on Function Menu. Set to 1 to enable feature on

Function Menu.

094

096

098

SAP MENU EN

DEF. ASP. RATIO

PRO:CENTRIC

0 / 1

0 ~ 4

0 ~ 3

Sets default aspect ratio at power up. See detailed descriptions and item 106.

Set to 0 to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for

GEM (Java Application) Mode. Set to 3 for HTML Mode.

1 ~ 100, 101 ~ 200,

201, 202, 255

099

BACK LIGHTING

202

Sets the level of the TV picture back lighting. (See detailed descriptions.)

102

103

104

ATSC BAND

0 ~ 4

0 / 1

Selects ATSC band.

ATSC TUNE MODE

START MINOR CH

Set to 1 (default) for Physical Channel scan. Set to 0 for Virtual Channel scan.

Selects Minor Start Channel. Set to 0 for NTSC.

0 ~ 255

To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on

power cycle.

106

ASP RATIO LOCK

0 / 1

116

117

VIDEO MUTE EN

FACT DEFAULT

0 / 1

Set to 0 for Normal. Set to 1 for Blank.

Set to 0 for Normal. Set to 1 to load presets for all Installer Menu settings.

Determines the powered status of the embedded b-LAN module and the

118

119

POWER SAVINGS

DATA CHANNEL

1, 3, 7, 9

0 ~ 135

GAME CONTROL/MPI port. (See detailed descriptions.)

Set to 0 to disable. Set to the RF channel number for the Data Channel of the

Pro:Centric server. (See detailed descriptions.)

Sets the hour for Wake On RF. The value “128” is displayed as “OFF.” Directly

entering 128 turns the Wake On RF feature OFF.

121

122

P:C RF WAKE HR

P:C RF WAKE MN

0 ~ 23, 128

0 ~ 59

128

Sets the minute for Wake On RF.

Caution: Installer Menu settings may affect options available

from the TV setup menus or the Function Menu.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Installer Menu (Cont.)

Detailed Descriptions of Installer Menu Items

000 - INSTALLER SEQUENCE

005 - CHAN LOCK (Channel Lock)

Speciﬁes entry sequence to the Installer Menu.

Channel Lock is ideal if the system must always be on the same

channel. Changing channels with the Channel Up/Down or keypad

numbers is impossible. Channel Lock is inactive if set to 0 (default).

0 = 9876

2 = 1478

1 = 4321

3 = 3698

Generally, this feature is used in connection with item 004 STRT

CHANNEL where the Start Channel may, for example, be set to

3 or 4. If the Start Channel is 3, then the TV will remain locked on

channel 3.

001 - POWER MANAGE (Power Management)

Determines hours of no activity before automatic shutoff. The

Power Management function is for saving energy. If set to 0,

Power Management is Off. Settings range from 0 ~ 7, with 1 ~ 7

representing the hours that the unit will remain ON, unless there

has been activity from either the control panel or remote control.

NOTE: For items 007, 008, and 009

For legacy reasons, the scale used is 0 – 63. The PTC software

will translate this to the 0 – 100 scale used by the TV.

002 - AC ON (AC Power Switchable)

To translate a TV volume level to the Installer Menu value, use

the following formula:

If set to 1, this allows the TV to turn ON when AC power is applied.

Pressing the ON button is not necessary. This is desirable if the TV

is plugged into a cable box or a power outlet controlled by a wall

switch. Use the Left/Right arrow keys to choose 0 or 1, where 0 is

the default (OFF), and 1 is ON.

Installer Value = TV Value x 63

100

Enter only the whole number (disregard fractions).

Note: If set to 1 (ON), the TV does not respond to ON/OFF

commands from either the remote or the display panel, and the

SLEEP TIMER is also nonfunctional.

007 - STRT VOLUME (Start Volume)

This function allows the Installer to determine the initial volume

level setting when the TV is turned ON. This feature is useful

for an in-house information channel, since the TV would always

select that volume level when it is turned ON. The range of values

are 0 - 63, 255. If 255 is selected, the current volume level will be

retained in memory when the TV is turned OFF; at turn ON, the

volume level will be automatically set at the previous or last level.

003 - BAND/AFC (Band/Automatic Frequency Control)

There are four possible settings for this option:

0 = Broadcast

2 = HRC

1 = CATV (default)

3 = IRC

If some channels were not found by Auto Tuning (Channel

Search), select the appropriate Band setting here, and add the

channels using the Channel Edit option in the Channel Menu.

008 - MIN VOLUME (Minimum Volume)

This function determines the minimum volume level allowable

with the Volume (VOL) Up/Down control. In this way, for example,

someone cannot set the volume too low to hear. The value range

is from 0 to 63. Use the Left/Right arrow keys to change values.

The factory default is 0, which provides the full range of volume

control, if item 009 MAX VOLUME is also set to 63. It may be best

to set the same value on every TV.

004 - STRT CHANNEL (Start Channel)

If active, this function allows you to determine the initial Major

Start Channel number when the TV is turned ON. This feature is

useful for an in-house information channel, since the TV would

always select that channel when it is turned ON. If set to 255,

the last channel tuned before the TV was turned OFF will be the

channel tuned when the TV is turned ON again.

Note: The minimum volume level cannot have a value setting

higher than the maximum volume level (described below).

0 = Aux

1 ~ 125 = Major Ch. #

126 = Map to Major CH 3

127 = Map to Major CH 4

253 = IP Start Channel

255 = Last Channel

009 - MAX VOLUME (Maximum Volume)

This function determines the maximum volume level allowable

with the Volume (VOL) Up/Down control. In this way, for example,

someone cannot set the volume level high enough to disturb

others. The value range is 0 to 63, with 63 as the default, which

gives the user the full range of volume control, if item 008 MIN

VOLUME is also set at 0. Use the Left/Right arrow keys to change

values. It may be best to set the same value on every TV.

Note: For a digital Start Channel, always remember to set item

104 to the Minor Start Channel number.

Note: 126 and 127 are mapped only in LodgeNet PPV Mode.

Note: The IP Start Channel shown above can only be set in the

FTG File Manager, which is used to conﬁgure TV CPUs for FTG

Mode. The same applies for the additional Major Channel number

range of 128 ~ 135 in Physical tuning and 128~999 in Virtual tuning

mode. This means that these values, if set, will only be visible in the

read-only Installer Menu when the TV is in FTG Mode via CPU. The

read-only display also will show additional information about the

channel, for example, the IP address and port number, etc.

Note: The maximum volume level cannot have a value setting

lower than the minimum volume level (described above).

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Installer Menu (Cont.)

010 - MUTE DISABLE

028 - CH. OVERIDE (Channel Override)

Enables or disables sound mute function. If set to 1, sound cannot If set to 1, the user can select channels with either Channel Up/

be muted. If set to 0, sound can be muted.

Down or by direct keypad entry. If set to 0, only those channels

that are active in the TV’s memory can be selected.

011 - KEY DEFEAT (Keyboard Defeat)

If set to 1, KEY DEFEAT prevents the end user from accessing the

on-screen menu(s) from the display panel—MENU SETTINGS,

OK, and menu navigation keys do not function. If set to 0, those

keys do function.

029 - OLD OCV (On Command Video™)

Set to 1 for operation with systems from On Command Corporation.

030 - ACK MASK

MPI Communication Parameter. When set to 1, enables ACK

feature of MPI.

Note: Users can always access the menus by pressing MENU on

the remote.

031 - POLL RATE

015 - SLEEP TIMER

MPI Communication Parameter. Selects poll rate for MPI. Step

size of 16 ms. Changing from default may affect communication

via MPI.

If set to 1, the Sleep Timer feature may be used. If set to 0, the

Sleep Timer is not available.

016 - EN TIMER (Enable On/Off Timers)

If set to 1, the Timer function is available to the end user and

enabled continuously. Set to 0 to disable On/Off timers.

032 - TIMING PULSE

MPI Communication Parameter. Sets baud rate for MPI. Step size

of 4.3 uS. Changing from default may affect communication via

MPI.

Note: Clock must be set in order for timers to be used.

017 - ALARM

035 - HDMI1 ENABLE

Gives the installer the option of making the Alarm function available

to the end user. If set to 1, the Alarm function is available to the end

user. Set to 0 to disable the Alarm function.

Set to 1 to enable display panel HDMI 1 input. Set to 0 to disable

display panel HDMI 1 input. Set to 5 to enable the HDMI 1 input

but disable the Hot Plug Detect (HPD) circuit.

Note: Clock must be set before the Alarm function will work.

Note: This setting is ignored if item 093 RJP AVAILABLE is set to 1.

020 - FEATURE LEVEL

039 - REAR AUX EN. (Rear Aux Enable)

Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0

to disable display panel rear Aux (Video 1) input.

Determines an additional IR code scheme to which the TV will

respond, allowing for the use of unique IR codes based on “bed

number” in a multi-TV single room installation. First determine the

IR mode; then select the bed number.

041 - SIMPLINK EN

Set to 0 to disable the SIMPLINK feature. Set to 1 to enable

SIMPLINK functionality without enabling remote control access to

the SIMPLINK Menu. Set to 2 to enable both SIMPLINK function-

ality and SIMPLINK Menu access, though note that the Speaker

menu option will be inaccessible/grayed out. Set to 3 to enable

all aspects of SIMPLINK feature and SIMPLINK Menu. If a home

theater device is connected to the TV, users can select either the

TV or HT (home theater) speaker.

Values

IR Mode

Bed #

N/A

Disabled

16 – 24

Multi-code Remote

1 – 9

Note: For further information, see documentation for the accessory

package that includes the multi-code remote.

021 - V-CHIP (Parental Control)

Set to 1 to activate V-Chip (Parental Control) and have it available

to the end user to ﬁlter and control or otherwise restrict program-

ming content that can appear. Set to 0 to turn the V-Chip feature

Off (not available to user); no programming restrictions can be set.

046 - STRT AUX SRCE (Start Aux Source)

Sets the starting Aux source. When turned ON, the TV will tune to

starting Aux source if item 004 STRT CHANNEL is set to 0.

1 = Video 1

3 = HDMI 1

4 = RGB

5 = HDMI 2

7 = HDMI 3

255 = Last Aux

022 - MAX BLK HRS (Maximum Block Hours)

Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)

block hours. Default setting is for 12 blocking hours.

Note: Above is applicable only if all Aux sources are enabled.

Note: This item is not available in the Installer Menu unless item

004 STRT CHANNEL is set to 0.

023 - CAPTION LOCK

If set to 0, captions are OFF when the TV is turned ON. Set to 1 to

use the caption setting conﬁgured before the TV was turned OFF

when the TV is turned ON.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Installer Menu (Cont.)

047 - AUX STATUS

Set to 1 for MPI Aux source to be reported as a channel number

080 - UPN MSB-2 (UPN Most Signiﬁcant Byte-2)

User programmable number, most signiﬁcant byte-2 readable by

instead of channel 0. Set to 0 to disable Aux identiﬁcation change. MPI command. Note: Not linked to serial number.

Controls MPI status channel response for Aux inputs.

081 - UPN LSB (UPN Least Signiﬁcant Byte)

053 - DIS. CH-TIME (Disable Channel-Time)

Set to 1 to disable the Channel-Time display; Channel-Time

display will not appear. Set to 0 to enable the Channel-Time

display.

User programmable number, least signiﬁcant byte readable by

MPI command. Note: Not linked to serial number.

082 - CHKSM ERROR (Checksum Error)

Enforces rigid MPI checksum validation. Set to 1 for validation.

Set to 0 to disable (does not check checksum on MPI async port).

SPI is always checked.

069 - EN. CH-T COL. (Enable Channel-Time Custom Color)

Set to 1 to enable custom color for the Channel-Time display. Set

to 0 to disable custom color for the Channel-Time display.

083 - HANDSHK TIME (Handshake Time)

070 - FOR. CH-TIME (Channel-Time Display Foreground Color) Adds an additional delay to the handshake time which is 64 msec,

Set according to Color Chart:

thus relaxing MPI timing requirements to be compatible with PC-

based Windows controlled systems. Range is 0 - 5.

(Timeout = 25.5MS + [25.5 MS* Handshake time].)

0 = Black

1 = Blue

3 = Cyan

4 = Red

6 = Yellow

7 = White

2 = Green

5 = Violet

084 - PERMANENT BLK (Permanent Block)

Note: If foreground color and background color are the same, the

menu background will be transparent.

Allows Lock (Parental Control) blocking schemes to be permanent

by disabling the blocking hours function. Set to 1 to install Parental

Control restrictions permanently. Set to 0 for user-speciﬁed hours

control of blocking schemes.

Note: Applies only to “Channel Not Available” message if item

073 CH NOT AVBLE is set to 1 (enabled). Also, items 070 FOR.

CH-TIME and 071 BCK. CH-TIME are not available in the Installer

Menu when item 069 EN. CH-T COL. is set to 0.

087 - REAR RGB EN. (Rear RGB Enable)

Controls access to rear RGB input on TV. Set to 0 to disable RGB

input. Set to 1 to enable RGB input. Set to 17 to initiate a one-

time automatic conﬁguration after an AC power cycle; otherwise,

automatic adjustment will be performed each time the RGB input

is accessed.

071 - BCK. CH-TIME (Channel-Time Display Background Color)

See description for item 070 FOR. CH-TIME above. The color

chart is the same for both items.

073 - CH NOT AVBLE (Channel Not Available)

If set to 1 and item 028 CH. OVERIDE is set to 0, a “NOT AVAIL-

ABLE” message is displayed when a user direct tunes a channel

that is not in the channel scan list available in memory.

088 - EN NOISE MUTE (Enable Noise Mute)

If set to 1, audio mutes if no signal is present.

Note: This item is not available in the Installer Menu when item

090 - KEY LOCK

028 CH. OVERIDE is set to 1.

If set to 1, display panel Channel, Volume, and Caption buttons

are disabled, Power button remains enabled. If set to 0, Channel,

Volume, Caption, and Power buttons are all enabled.

075 - REVERT CH (Revert to Start Channel)

If set to 1 and loss of MPI communication occurs, TV automatically

tunes to the speciﬁed Start Channel.

091 - HDMI2 ENABLE

Set to 1 to enable display panel HDMI 2 input. Set to 0 to disable

display panel HDMI 2 input.

Note: This item is not available in the Installer Menu when item

004 STRT CHANNEL is set to 255.

092 - HDMI3 ENABLE

078 - UPN MSB (UPN Most Signiﬁcant Byte)

Set to 1 to enable display panel HDMI 3 input. Set to 0 to disable

display panel HDMI 3 input.

User programmable number, most signiﬁcant byte readable by

MPI command. Note: Not linked to serial number.

079 - UPN MSB-1 (UPN Most Signiﬁcant Byte-1)

User programmable number, most signiﬁcant byte-1 readable by

MPI command. Note: Not linked to serial number.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Installer Menu (Cont.)

093 - RJP AVAILABLE (Remote Jack Pack Available)

098 - PRO:CENTRIC

Selects the Pro:Centric Application Mode. Set to 0 (default) to

disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2

for GEM (Java Application) Mode. Set to 3 for HTML Mode.

• 0 = Remote jack pack is not available or disabled.

• 1 = Legacy Model RJPs: HDMI Mode

Enables RJP feature for use with full cable bundle models. In

this mode, when an HDMI source is connected to the RJP, both

digital video and audio are expected via the HDMI cable. If no

digital audio is present, no audio will be heard.

The TV must be turned OFF for a few seconds to initiate the

Pro:Centric application download. When the TV is turned back ON,

it may take several minutes to load the Pro:Centric application after

the initial download.

• 2 = Legacy Model RJPs: DVI Mode

Note: This item is not available in the Installer Menu when item

119 DATA CHANNEL is set to 0.

Enables RJP feature for use with full cable bundle models. In

this mode, when an HDMI/DVI source is connected to the RJP,

only digital video is expected via the HDMI cable. Analog audio

is provided via a separate cable, from the source, connected to

an RJP AUDIO IN. If no analog audio cable is connected, tuner

audio will be heard.

099 - BACK LIGHTING

Sets the TV screen brightness at power up. Default setting is 202.

• 1 - 100 Static Back Lighting

(1 = Dimmest picture, 100 = Brightest picture)

• 5 = Scaler Model RJPs: HDMI Mode

Enables RJP feature for use with reduced cable bundle models.

In this mode, when an HDMI source is connected to the RJP,

both digital video and audio are expected via the HDMI cable. If

no digital audio is present, no audio will be heard.

• 101 - 200 Dynamic Back Lighting

(101 = Dimmest picture, 200 = Brightest picture)

The TV automatically controls back lighting depending upon the

picture level of the current program.

• 6 = Scaler Model RJPs: DVI Mode

• 201 Automatic Static Back Lighting

Enables RJP feature for use with reduced cable bundle models.

In this mode, when an HDMI/DVI source is connected to the

RJP, only digital video is expected via the HDMI cable. Analog

audio is provided via separate cable, from the source, connect-

ed to an RJP AUDIO IN. If no analog audio cable is connected,

tuner audio will be heard.

The TV automatically controls back lighting depending upon

external spectral sensitivity.

• 202 Automatic Dynamic Back Lighting

The TV automatically controls back lighting depending upon

external spectral sensitivity and the picture level of the current

program.

Notes:

If set to 255, back lighting is controlled via the Picture settings in

the TV setup menus.

See Reference section, “RJP Model List & Input Auto-sensing

Hierarchy.” If RJP AVAILABLE is set to 1, 2, 5, or 6, item 040

AUTO CAMPORT is automatically set to 0. Settings 1, 2, 5, and 6

allow the lodge staff to customize each TV’s RJP setup based on

customer requirements.

102 - ATSC BAND

Sets up TV to receive different types of incoming signals:

0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.

094 - SAP MENU EN (2nd Audio Program)

Set to 1 to enable SAP feature on Function Menu, if Function

Menu is available (i.e., TV is not in Pass-through Mode). Set to

0 to disable SAP feature on Function Menu, if Function Menu is

available.

103 - ATSC TUNE MODE

Sets ATSC tuning mode. Default set to 1 for Physical Channel

scan. Set to 0 for Virtual Channel scan.

104 - START MINOR CHANNEL

Sets Minor Start Channel number at power up. 0 = NTSC. If not

0, number selected is the digital channel’s Minor Start Channel

number.

096 - DEF. ASP. RATIO (Default Aspect Ratio)

Selects default aspect ratio at power up.

• Set to 0 for Set By System.

• Set to 1 for 4:3.

Note: This item is not available in the Installer Menu when item

004 STRT CHANNEL is set to 0 or 255.

• Set to 2 for 16:9 (Factory Default).

• Set to 3 for Just Scan.

• Set to 4 for Zoom.

106 - ASP RATIO LOCK (Aspect Ratio Lock)

Set to 1 to retain previous aspect ratio with power off. Set to 0 to

retain default aspect ratio with power off. See item 096 DEF. ASP.

RATIO above.

Note: This item is not available in the Installer Menu unless item

106 ASP RATIO LOCK is set to 0.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Installer Menu (Cont.)

116 - VIDEO MUTE EN (Video Mute Enable)

119 - DATA CHANNEL

Set to 0 for Normal. Set to 1 for Blank.

Set to 0 (default) to disable. Set to the RF channel number for

the Data Channel of the Pro:Centric server to enable application

(item 098 PRO:CENTRIC must be set appropriately) and/or TV

E-Z Installation (splash screen, configuration, and firmware) data

downloads.

117 - FACT DEFAULT (Factory Default)

Set to 0 for normal. Set to 1 to restore the factory default settings

of all Installer Menu items. The restoring of factory defaults will

also re-activate the Automated Installation Routine Wizard (see

pages 11 to 14).

Note: Pro:Centric application updates are downloaded from the

Pro:Centric server to the TV when the TV is turned ON; however,

TV E-Z Installation updates are downloaded to the TV when the TV

is turned OFF. While E-Z Installation updates are in progress, it is

not possible to turn ON the TV.

Caution: If set to 1, this will restore the factory

defaults and clear the channel lineup, including any

assigned channel icons and custom text labels.

Note: The Data Channel is automatically set to “253” if Media

Type is set to “IP” either in the Automated Installation Routine

Wizard or in the IP Environment / Pro:Centric Menu on the TV

(see “Automated Installation Routine Wizard” on pages 11 to 14

or “Pro:Centric Setup” on page 53, respectively) or if the Data

Channel Installer Menu item is set to “IP Address” in the FTG

File Manager, which is used to conﬁgure TV CPUs for FTG Mode

operation. It is not possible to change the value to “253” directly in

the Installer Menu.

Note: See also Reference section, “Restoring Factory Defaults on

the TV(s),” for further information.

118 - POWER SAVINGS

Default set to 3—the power circuitry for both the embedded b-

LAN module and the GAME CONTROL/MPI port is only powered

when the TV is turned ON. When the TV is in Standby Mode, the

embedded b-LAN and the GAME CONTROL/MPI port are not

powered.

Note that the TV must be turned ON in order to communicate with

the embedded b-LAN module for conﬁguration and control when

POWER SAVINGS is set to 3. If POWER SAVINGS is set to 1,

the b-LAN module is always powered.

121 - P:C RF WAKE HR

Set the hour from 0 to 23 for Wake On RF. This item uses the 24-

hour clock format. The value “128” is displayed as “OFF.” Directly

entering 128 turns the Wake On RF feature OFF.

Similarly, if MPI communication is required for external MPI

control, POWER SAVINGS should be set to 1 so that the GAME

CONTROL/MPI port circuitry is always powered.

Note: This item is only available in the Installer Menu when item

119 DATA CHANNEL is set to an RF channel 1 to 135.

Note: Items 121 P:C RF WAKE HR and 122 P:C RF WAKE MN

are not available when item 119 DATA CHANNEL is set to 253

(Media Type = IP).

For specific applications, the RS-232 (DB9) port may be used to

provide +12v/1A external power (for example, to an external MPI

control device). In this case, Installer Menu item 118 POWER

SAVINGS must be set to 9—both the b-LAN module and the

GAME CONTROL/MPI port circuitry are always powered, and the

external power is provided on pin 9 of the RS-232 port.

122 - P:C RF WAKE MN

Set the minute from 0 to 59 for Wake On RF.

Note: This item is only available in the Installer Menu when item

119 DATA CHANNEL is set to an RF channel 1 to 135 and when

item 121 P:C RF WAKE HR is set to an hour 0 to 23.

Note: See Reference section, “b-LAN Setup & Overview,” for

further information.

Caution: POWER SAVINGS should NEVER be set to 7.

This setting is intended for factory use only.

Note: Items 121 P:C RF WAKE HR and 122 P:C RF WAKE MN

are not available when item 119 DATA CHANNEL is set to 253

(Media Type = IP).

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Channel Icons / Custom Text Labels (2-5-4 + MENU Mode)

Changing Channel Icons and/or Adding or Editing

Custom Text Labels in the Channel-Time Display

Changing icons and/or adding or editing custom text labels

can only be done if there are channels that have been

transferred to the TV’s PTC either during Master TV Setup

(see pages 15 to 18) or by cloning (USB memory device /

.tll file or clone programmer only).

If there is no pre-assigned icon for a channel, you can add

a custom text label of up to seven (7) characters to help

identify the channel or network. Also, if desired, a custom

text label can be added to the Channel-Time display in

addition to a pre-assigned icon. You may also add text

labels for the Aux input sources to clearly identify the

devices that are connected to the Aux inputs.

Note: A blank letter space is available between “Z” and “!”.

To perform channel editing/labeling:

1. Access the Installer Menu (see “Accessing the Installer

Menu” on page 19 for further information).

(Icon)

2. Press 2-5-4 + MENU SETTINGS on the Installer

Remote to access the Channel Label Editing Menu.

XYZ

3. Change channel icons and/or add or edit custom text

labels as described in the procedures below. (You can

do this more than once.)

NETWORK

(Custom Text Label)

1 2 3 4 5

4. To exit the menu when done, press MENU SETTINGS.

Changing a Channel’s Icon on

the Master TV

Adding/Editing Channel Labels

on the Master TV

Adding/Editing Source Labels

on the Master TV

1. Use Channel Up/Down to select

the desired channel.

1. Use Channel Up/Down to select

the desired channel.

1. Press INPUT to select the desired

Aux input source: AV, RGB, HDMI,

HDMI2, or HDMI3.

2. Use the Left/Right arrow keys

to select the thin letter “I” on the

Channel-Time display.

2. Press the Left or Right arrow

repeatedly until the numbers 1 to 7

appear on the display. The number

shows the position of the character

that can be changed. Number 1 is

the ﬁrst character, number 2 the

second character, etc.

2. Press the Left or Right arrow

repeatedly until the numbers 0 to 9

appear on the display. The number

shows the position of the character

that can be changed.

3. Use the Up/Down arrow keys to

select the icon with which you want

to identify the channel. (If you know

the icon number, enter the number,

and press OK.)

3. Use the Up/Down arrow keys to

select the desired character.

3. Use the Up/Down arrow keys to

select the desired character.

4. Proceed to add/edit custom text

labels, or go to the next channel.

4. Press INPUT for the next Aux input,

or use Channel Up/Down to return

to channels.

4. Proceed to the next number posi-

tion, or go to the next channel.

Installer Remote Control Key Functions for Master TV Channel Label Editing Menu

• Channel Up/Down: Tunes to the next channel in scan.

• Left/Right Arrows: Select the item to change. If “I” is

shown, the icon can be changed. If a number is shown, it

indicates the position of the character that can be changed.

• Up/Down Arrows: Select the icon or the character to be

displayed. Tip: Arrows can be held down for fast scrolling.

• 0 – 9: Use to enter the index number of the icon, if

known.

• OK: Changes the icon after the icon number has been

entered.

• INPUT: Changes the Aux input label.

• MENU SETTINGS: Exits the editing process.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Cloning Overview

IMPORTANT CLONING INFORMATION

There are four different procedures for cloning a Master TV Setup, each with its own advantages and

limitations (see also “Cloning Methods” on page 15):

• Using a USB memory device / .tlx ﬁle

• Using a USB memory device / .tll ﬁle

• Using a TLL-1100A clone programmer

• Using a LT2002 clone programmer

Each cloning method is described in further detail on the pages that follow. As you perform cloning

procedures, be sure to complete each task as indicated. If a procedure or step is omitted or not

performed completely, cloning may not work. At each step, pay attention to ensure the TV screen shows

the proper message when cloning. If the message indicated does not appear, there is a problem with that

step, and cloning may not be successful.

Caution: Copying a blank or incorrect memory into a TV from a clone programmer will

cause the TV to operate erratically or become inoperable.

Caution: If the TV is in LodgeNet PPV Mode (check with the site administrator if you are not

certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will

damage the clone programmer.

Before you begin cloning:

• Complete the Custom Master TV Setup procedure (see pages 15 to 18).

• All equipment should be connected to power and turned ON.

• Both the Master and Target TVs must be in Pass-through Mode (i.e., the TV setup menus should be

displayed when you press MENU SETTINGS on the Installer Remote).

• Learning and Teaching is only possible between identical model TVs.

• If using a USB memory device, ensure the USB device has been formatted with FAT format.

• If using a USB memory device / .tlx ﬁle, ensure that the Master TV Setup does not contain a Channel

Map; otherwise, Teaching will result in the Target TV(s) being conﬁgured for FTG Mode via CPU.

• For both Master and Target TVs—If using a clone programmer, ensure the TV is tuned to either an Aux

input or an analog (not a digital) channel.

• LT2002 only—Make sure the batteries in the clone programmer are fresh. If batteries are removed, the

clone programmer clock time (if set) will be lost (see page 37 for information on the clone programmer

clock).

Caution: Do not unplug the TV power cord or remove/disconnect the USB memory device/

clone programmer while Learning or Teaching, as doing so may cause the TV to malfunction

or harm the USB device/clone programmer, respectively.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

USB Cloning Procedures

Learning / Teaching a Master TV Setup using a USB Memory Device / .tlx File

USB Cloning Notes

• Read the IMPORTANT CLONING INFORMATION on page 29 before beginning any cloning procedures.

In particular, ensure that the Master TV Setup does not contain a Channel Map; otherwise, Teaching will

result in the Target TV(s) being conﬁgured for FTG Mode via CPU.

• You may edit the ﬁlename as part of the Learning procedure; however, a ﬁle with edited contents will

not be recognized.

• It is not possible to clone a Master TV’s clock using a USB memory device. Either set a Target TV’s

clock manually, or use the Auto Clock setting in the TV setup menus.

Learn Setup from Master TV

USB Download Menu

1. Ensure the Master TV is set up completely and in Pass-through Mode.

Upgrade TV Software

2. Plug the USB memory device into the USB IN port on the Master TV.

Upgrade PTC Software

3. Press MENU SETTINGS on the Installer Remote to display the TV

Teach To TV (TLL)

setup menus. Use the arrow navigation keys to select/highlight the

Option menu icon, and then press the number “7” key a total of seven

times to display the USB Download Menu.

Teach To TV (TLX)

Learn From TV (TLL)

Learn From TV (TLX)

4. To gain access to the “Learn From TV” option in the USB Download

Menu, key in the password used to access the Installer Menu

(Example: Press 9-8-7-6).

Learn From TV (TLX)

5. Use the Up/Down arrow keys to select Learn From TV (TLX), and then

press OK.

Select the ﬁle name and press OK to start

6. To differentiate this .tlx ﬁle from others, you can use the Up/Down

arrow keys to change the last ﬁve digits of the ﬁlename. Press OK when

you are ready to initiate Learning.

xxLT770H-UA00003.TLX

Learning status will be shown on a progress bar in a new window. When

the Learning process is complete, the USB Download menu will reappear

on the screen.

Learn From TV

UPDATING...

7. When Learning is done, press on the Installer Remote to exit the

USB Download Menu, and remove the USB memory device from the

Master TV.

25%

Do not unplug!

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

USB Cloning Procedures (Cont.)

Teach Master TV Setup to Target TV

1. Turn ON the Target TV.

The next step depends on whether the Automated Installation Routine

Wizard appears on the screen when you turn ON the TV:

• If the wizard is displayed, the TV is already in the required factory

default state. Use the Up/Down arrow keys on the Installer Remote

to select Exit from the Welcome screen, and press OK to exit the

wizard. Then, go to step 3.

• Otherwise, ensure the Target TV is in Pass-through Mode. Then,

continue with step 2.

2. Use the Installer Remote to access the Target TV Installer Menu (see

“Accessing the Installer Menu” on page 19 for further information). Set

Installer Menu item 117 FACT DEFAULT to 001, and press OK. When

the value changes back to 0, press OK again to exit the Installer Menu.

Note: This step restores factory default settings on the TV, which will

in turn re-activate the Automated Installation Routine Wizard. Use the

Up/Down arrow keys on the Installer Remote to select Exit from the

Welcome screen. Then, press OK to exit the wizard.

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

3. Plug the USB memory device with the .tlx ﬁle into the Target TV USB IN

port.

4. Press MENU SETTINGS on the Installer Remote to display the TV

setup menus. Use the arrow navigation keys to select/highlight the

Option menu icon, and then press the number “7” key a total of seven

times to display the USB Download Menu.

Teach To TV (TLX)

5. Use the Up/Down arrow keys to select Teach To TV (TLX), and then

xxLT770H-UA00003.TLX

press OK.

6. Use the Up/Down arrow keys to select the Master TV Setup you want to

install, and then press OK. Note: Filenames identify the TV and the TLX

version (see example at right).

Teaching status will be shown on a progress bar in a new window.

When the Teaching process is complete, the TV will brieﬂy display a

“Teaching Completed” window and then exit the USB Download Menu.

Teach To TV

UPDATING...

7. Remove the USB memory device from the Target TV, and verify that

the Master TV Setup is now resident on the Target TV.

50%

Do not unplug!

Note: After the Teaching process is complete, the TV tunes according to

the setting of Installer Menu item 004 STRT CHANNEL (Start Channel). If

a Start Channel is speciﬁed, the TV will tune to that channel; otherwise, the

TV will return to the last channel tuned.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

USB Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using a USB Memory Device / .tll File

USB Cloning Notes

• Read the IMPORTANT CLONING INFORMATION on page 29 before beginning any cloning procedures.

• You may edit a ﬁlename as part of the Learning procedure; however, a ﬁle with edited contents will not

be recognized.

• It is not possible to clone a Master TV’s clock using a USB memory device. Either set a Target TV’s clock

manually, or use the Auto Clock setting in the TV setup menus.

Learn Setup from Master TV

USB Download Menu

1. Ensure the Master TV is set up completely and in Pass-through Mode.

Upgrade TV Software

2. Plug the USB memory device into the USB IN port on the Master TV.

Upgrade PTC Software

3. Press MENU SETTINGS on the Installer Remote to display the TV

Teach To TV (TLL)

setup menus. Use the arrow navigation keys to select/highlight the

Option menu icon, and then press the number “7” key a total of seven

Teach To TV (TLX)

Learn From TV (TLL)

times to display the USB Download Menu.

Learn From TV (TLX)

4. To gain access to the “Learn From TV” option in the USB Download

Menu, key in the password used to access the Installer Menu

(Example: Press 9-8-7-6).

Learn From TV (TLL)

5. Use the Up/Down arrow keys to select Learn From TV (TLL), and then

press OK.

Select the ﬁle name and press OK to start

6. To differentiate this .tll ﬁle from others, you can use the Up/Down arrow

keys to change the last ﬁve digits of the ﬁlename. Press OK when you

are ready to initiate Learning.

xxLT770H-UA00001.TLL

Learning status will be shown on a progress bar in a new window. When

the Learning process is complete, the USB Download menu will reappear

on the screen.

Learn From TV

UPDATING...

7. When Learning is done, press on the Installer Remote to exit the

USB Download Menu, and remove the USB memory device from the

Master TV.

25%

Do not remove the USB from the port!

Do not unplug!

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

USB Cloning Procedures (Cont.)

Teach Master TV Setup to Target TV

1. Turn ON the Target TV.

The next step depends on whether the Automated Installation Routine

Wizard appears on the screen when you turn ON the TV:

• If the wizard is displayed, the TV is already in the required factory

default state. Use the Up/Down arrow keys on the Installer

Remote to select Exit from the Welcome screen, and press OK to exit

the wizard. Then, go to step 3.

• Otherwise, ensure the Target TV is in Pass-through Mode. Then,

continue with step 2.

2. Use the Installer Remote to access the Target TV Installer Menu (see

“Accessing the Installer Menu” on page 19 for further information). Set

Installer Menu item 117 FACT DEFAULT to 001, and press OK. When

the value changes back to 0, press OK again to exit the Installer Menu.

Note: This step restores factory default settings on the TV, which will

in turn re-activate the Automated Installation Routine Wizard. Use the

Up/Down arrow keys on the Installer Remote to select Exit from the

Welcome screen. Then, press OK to exit the wizard.

3. Tune/set the TV to an analog or digital channel or Aux input (ideally the

same source tuned for 2-5-5 + MENU Mode during the Master TV Setup

procedure).

4. Plug the USB memory device with the .tll ﬁle into the Target TV USB IN

port.

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

5. Press MENU SETTINGS on the Installer Remote to display the TV

setup menus. Use the arrow navigation keys to select/highlight the

Option menu icon, and then press the number “7” key a total of seven

times to display the USB Download Menu.

Teach To TV (TLX)

6. Use the Up/Down arrow keys to select Teach To TV (TLL), and then

press OK.

7. Use the Up/Down arrow keys to select the Master TV Setup you want to

install, and then press OK. Note: Filenames identify the TV and the TLL

version (see example at right).

Teach To TV (TLL)

xxLT770H-UA00001.TLL

Teaching status will be shown on a progress bar in a new window.

When the Teaching process is complete, the USB Download menu will

reappear on the screen.

8. When Teaching is done, press on the Installer Remote to exit the

USB Download Menu, remove the USB memory device from the Target

TV, and turn OFF the TV.

Teach To TV

UPDATING...

50%

9. After a few seconds, turn ON the TV, and verify that the Master TV

Setup is now resident on the Target TV.

Do not remove the USB from the port!

Do not unplug!

Note: When you turn it back ON, the TV will tune according to the setting

of Installer Menu item 004 STRT CHANNEL (Start Channel). If a Start

Channel is specified, the TV will tune to that channel; otherwise, the TV

will return to the last channel tuned.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Clone Programmer Cloning Procedures

Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer

Caution: If the TV is in LodgeNet PPV Mode (check with the site administrator if you are not

certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will

damage the clone programmer.

Cloning is accomplished using the

TV/clone programmer MPI ports for

communication (see figure).

TLL-1100A Clone

TV Link

Loader

Programmer

TLL1100A

Ready

Antenna

or CATV

TLL-1100A Cloning Notes

• Read the IMPORTANT CLONING

INFORMATION on page 29 before

MODE

beginning any cloning procedures.

CLONE SELECTION MENU

MPI

Cable

ENTER

Selected Bank: CBankX Saved

• Ensure the TLL-1100A is either fully

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

charged or connected to AC power.

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

RECEIVE

SEND

(6) DISPLAY CLONE SETUP

• Learning and Teaching is only

TLL-1100A

possible between identical model

TVs; however, the TLL-1100A can

store up to eight different Master

TV Setups.

Learn Setup from Master TV

1. Ensure the Master TV is set up completely and in Pass-through Mode.

2. Tune/set the TV to an analog channel or Aux input, and then, plug one end

of the MPI cable into the TV MPI port.

3. Turn ON the TLL-1100A.

4. Use the MODE button on the TLL-1100A to select Clone Mode.

5. Use the Left/Right arrows on the TLL-1100A to select the Memory CBank

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1) LEARN FROM TV

(1 to 8) in which to store the Master TV Setup.

6. Plug the other end of the MPI cable into the MPI port on the bottom of the

TLL-1100A. The Clone Selection Menu will display on the TV screen.

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

7. Press 1 on the Installer Remote to select LEARN FROM TV from the

Clone Selection Menu. Then, press OK to transfer the Master TV Setup

into CBankX on the TLL-1100A.

(6) DISPLAY CLONE SETUP

CLONE CLOCK = XX:XX

Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will

be displayed on the screen while the TLL-1100A copies the Master Setup.

When the Learning process is complete, a “LEARNING COMPLETE”

message will be displayed.

CLOCK = XX:XX

THE CLONE IS VERSION VX.X.X

To change menu items, press

channel keys or digits.

To execute item, press Enter.

8. When Learning is complete, disconnect the MPI cable from the Master TV.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Clone Programmer Cloning Procedures (Cont.)

(Optional) Set the Clock

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1) LEARN FROM TV

Set the time on a Master TV’s clock. (If the time has already been copied

from a TV into the TLL-1100A clone programmer, you can set the Master

TV’s clock by copying the time from the clone programmer.) The TLL-1100A

can copy the current time to both a Master TV and to the clone’s internal

clock—accurate to within one minute.

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

Since the TLL-1100A’s time cannot be set directly, the current time needs

to be copied from an LG TV equipped with an enabled MPI port.

CLONE CLOCK = XX:XX

CLOCK = XX:XX

After the time is copied to the TLL-1100A clone programmer, the current

time will be maintained and can then be transferred to another TV. (This can

be a Master TV or another TV which has already had the features set up.)

THE CLONE IS VERSION VX.X.X

To change menu items, press

channel keys or digits.

To execute item, press Enter.

Teach Master TV Setup to Target TV

1. Turn ON the Target TV.

The next step depends on whether the Automated Installation Routine

Wizard appears on the screen when you turn ON the TV:

• If the wizard is displayed, the TV is already in the required factory

default state. Use the Up/Down arrow keys on the Installer Remote to

select Exit from the Welcome screen, and press OK to exit the wizard.

Then, go to step 3.

• Otherwise, ensure the Target TV is in Pass-through Mode. Then,

continue with step 2.

2. Use the Installer Remote to access the Target TV Installer Menu (see

“Accessing the Installer Menu” on page 19 for further information). Set

Installer Menu item 117 FACT DEFAULT to 001, and press OK. When

the value changes back to 0, press OK again to exit the Installer Menu.

Note: This step restores factory default settings on the TV, which will in

turn re-activate the Automated Installation Routine Wizard. Use the Up/

Down arrow keys on the Installer Remote to select Exit from the Welcome

screen. Then, press OK to exit the wizard.

3. Tune/set the TV to an analog channel or Aux input (ideally the same

source tuned for 2-5-5 + MENU Mode during the Master TV Setup

procedure), and then connect the MPI cable to the MPI port on the Target

TV. The Clone Selection Menu will display on the TV screen.

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1) LEARN FROM TV

4. Ensure the correct Memory CBank(X) is selected on the TLL-1100A.

(2) TEACH TO TV

5. Press 2 on the Installer Remote to select TEACH TO TV from the Clone

Selection Menu. Then, press OK to transfer the Master TV Setup to the

Target TV.

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will

be displayed on the screen during Teaching. When the Teaching process

is complete, a “TEACHING COMPLETE” message will be displayed.

CLONE CLOCK = XX:XX

CLOCK = XX:XX

THE CLONE IS VERSION VX.X.X

6. When Teaching is done, disconnect the MPI cable from the Target TV,

and turn OFF the TV.

To change menu items, press

channel keys or digits.

To execute item, press Enter.

7. After a few seconds, turn ON the TV, and verify that the Master TV

Setup is now resident on the Target TV.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Clone Programmer Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer

Caution: If the TV is in LodgeNet PPV Mode (check with the site administrator if you are not

certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will

damage the clone programmer.

Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).

LT2002 Cloning Notes

• Read the IMPORTANT CLONING

MPI

INFORMATION on page 29 before

beginning any cloning procedures.

Cable

Antenna

or CATV

• A slow ﬂashing green light indicates

that there are communication

problems between the TV and the

LT2002. If this is the case, check for

a damaged cable, poor contacts, or

other connection troubles.

Ferrite Core

(TDK, ZCAT

2035-0930)

Connect cable to

TV MPI Jack and

follow on screen

instructions

Status

Indicator

MPI

Reset

Color

•

green

red

battery ok

battery low

Blink pattern

power on

no communications

• If the status indicator is red, the

LT2002 batteries are low and should

be replaced. Install four (4) high-

quality alkaline AA batteries.

•

slow

heartbeat power on

communications ok

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION

THE SW IS REVISION

CLONE CLOCK

TV CLOCK

XX:XX

• Learning and Teaching is only

possible between identical model TVs;

however, the LT2002 can store up to

three different Master TV Setups.

- PRESS ANY KEY TO CONTINUE.

QuickSet II Programmer

- DISCONNECT CLONE WHEN DONE.

LT2002

LT2002 Clone

Programmer

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA

Learn Setup from Master TV

1. Ensure the Master TV is set up completely and in Pass-through Mode.

CLONE SELECTION MENU

2. Tune/set the TV to an analog channel or Aux input, and then plug one end of

the MPI cable into the TV MPI port.

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

3. If there is a good connection after the LT2002 is connected to the TV MPI

port, “THE CLONE HAS CONTROL OF THE TV” message will appear on

the TV screen. Press any key on the Installer Remote to access the LT2002

Clone Selection Menu.

(6) DISPLAY CLONE SETUP

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

4. Press 1 on the Installer Remote to select LEARN FROM TV from the Clone

Selection Menu; then press OK to proceed to the Memory Bank Selection

Menu.

- TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

5. Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in

SAVE TV SETUP IN SELECTED

CLONE MEMORY

which to store the Master Setup. Then, press OK.

Note: If you choose a Memory Bank that already has a Master device’s setup

programmed into it, that setup will be overwritten by the new Master TV Setup.

(1) MEMORY 1 VER XX REV XX

(2) MEMORY 2 VER XX REV XX

(3) MEMORY 3 VER XX REV XX

(4) RETURN TO CLONE MENU

6. Verify the Learning setup information on the next screen, and then press

POWER to transfer the Master TV Setup into the selected Memory Bank on

the LT2002.

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will

be displayed on the screen while the LT2002 copies the Master Setup. When

the Learning process is complete, a “LEARNING COMPLETE” message will

be displayed.

- TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

7. When Learning is complete, disconnect the MPI cable from the Master TV.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Clone Programmer Cloning Procedures (Cont.)

(Optional) Set the Clock

Set the time on a Master TV’s clock. (If the time has already been copied from a

TV into the LT2002 clone programmer, you can set the Master TV’s clock by

copying the time from the clone programmer.) The LT2002 can copy the current

time to both a Master TV and to the clone’s internal clock—accurate to within one

minute. (Another reason that the LT2002 should be equipped with fresh, high-

quality alkaline batteries, is for it to keep the time as accurately as possible.)

CLONE SELECTION MENU

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

Since the LT2002’s time cannot be set directly, the current time needs to be

copied from an LG TV equipped with an enabled MPI port.

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

- TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

After the time is copied to the LT2002 clone programmer, the current time will be

maintained and can then be transferred to another TV. (This can be a Master TV

or another TV which has already had the features set up.)

Teach Master TV Setup to Target TV

1. Turn ON the Target TV.

The next step depends on whether the Automated Installation Routine Wizard

appears on the screen when you turn ON the TV:

• If the wizard is displayed, the TV is already in the required factory default state.

Use the Up/Down arrow keys on the Installer Remote to select Exit from the

Welcome screen, and press OK to exit the wizard. Then, go to step 3.

• Otherwise, ensure the Target TV is in Pass-through Mode. Then, continue with

step 2.

2. Use the Installer Remote to access the Target TV Installer Menu (see “Access-

ing the Installer Menu” on page 19 for further information). Set Installer Menu

item 117 FACT DEFAULT to 001, and press OK. When the value changes back

to 0, press OK again to exit the Installer Menu.

Note: This step restores factory default settings on the TV, which will in turn

re-activate the Automated Installation Routine Wizard. Use the Up/Down arrow

keys on the Installer Remote to select Exit from the Welcome screen. Then,

press OK to exit the wizard.

CLONE SELECTION MENU

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

3. Tune/set the TV to an analog channel or Aux input (ideally the same source

tuned for 2-5-5 + MENU Mode during the Master TV Setup procedure), and

then connect the MPI cable to the MPI port on the Target TV.

(6) DISPLAY CLONE SETUP

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

4. With “THE CLONE HAS CONTROL OF TV” message on display, press 2 on

the Installer Remote to select TEACH TO TV from the LT2002 Clone Selection

Menu. Then, press OK.

- TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

5. Select the LT2002 Memory Bank in which the new Master TV Setup is located,

and press OK.

COPY SELECTED CLONE MEMORY

TO TV

6. Verify the Teaching setup information on the next screen, and then press

(1) MEMORY 1 VER XX REV XX

(2) MEMORY 2 VER XX REV XX

(3) MEMORY 3 VER XX REV XX

(4) RETURN TO CLONE MENU

POWER to transfer the Master TV Setup to the Target TV.

Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will be

displayed on-screen during Teaching. When the Teaching process is complete,

a “TEACHING COMPLETE” message will be displayed.

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

7. When Teaching is done, disconnect the MPI cable from the Target TV, and turn

OFF the TV.

- TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

8. After a few seconds, turn ON the TV, and verify that the Master TV Setup is

now resident on the Target TV.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG Mode of Operation Overview

FTG Mode via CPU or EBL

FTG Mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels.

As indicated in the introduction to this document, there are two separate and distinct methods for configuring

LT770H TVs for FTG Mode of operation: one (new) method is to configure the TV CPU for FTG Mode

operation, while the other is to configure the TV EBL for FTG Mode operation. FROM A LOCAL

CONFIGURATION STANDPOINT, EACH OF THESE METHODS IS MUTUALLY EXCLUSIVE. IF THE

CPU IS IN FTG MODE, THE EBL CANNOT BE SWITCHED TO FTG MODE. LIKEWISE, IF THE EBL IS

IN FTG MODE, THE CPU CANNOT BE SWITCHED TO FTG MODE.

FTG Mode via CPU

FTG Mode via EBL

This mode provides the following features:

• Logical channels mapped to either RF or IP delivered

content.

• Logical channels mapped to RF delivered content.

• Digital RF channel minor (program) numbers up to 255.

• FTG Channel Map of up to 141 logical channels.

• Start Channel set for RF or Aux input delivered content.

• Pro:Centric data delivery over RF.

• Digital RF channel minor (program) numbers up to 999.

• FTG Channel Map of up to 600 logical channels.

• Start Channel set for RF, Aux input, or IP delivered content.

• Pro:Centric data delivery over RF or IP.

FTG Mode via EBL requires LG FTG Device Conﬁguration

Application PC software. In this mode, the EBL is the owner

of the FTG Channel Map and must be conﬁgured with an

FTG Channel Map and FTG Installer Menu settings using

one of the following processes:

FTG Mode via CPU requires that you use LG FTG File

Manager PC software to create an FTG Conﬁguration (.tlx)

ﬁle. In this mode, the CPU is the owner of the FTG Channel

Map and must be conﬁgured with an FTG Channel Map

and FTG Installer Menu settings using one of the following

processes:

• Local: Conﬁgure an individual LT770H TV’s EBL via its

TV-LINK CFG jack using a direct PC-to-TV connection and

the FTG Device Conﬁguration Application. See Reference

section, “FTG Mode via EBL (Local Conﬁguration),” for

information on the “Write” process for an FTG Channel

Map and FTG Installer Menu settings.

• Local: Conﬁgure an individual LT770H TV via its USB port

using an FTG Conﬁguration (.tlx) ﬁle on a USB memory

device. The “Teach to TV (TLX)” process, along with

associated procedures, is described on pages 40 to 44.

• Remote: Conﬁgure all LT770H TVs at the site using a

Pro:Centric server head end device (Example: PCS150R).

Load an FTG Conﬁguration (.tlx) ﬁle on the Pro:Centric

server using the TV E-Z Installation “Conﬁguration”

option in the Pro:Centric server Admin Client. Refer to the

Pro:Centric Server Admin Client User Guide for further

information.

• Remote: Conﬁgure all LT770H TV EBLs at the site using

a Free-To-Guest Management Appliance (FMA) head

end device (Example: FMA-LG101). Refer to the Free-

To-Guest (FTG) Device Configuration Application

User Guide and/or the Installation & Conﬁguration Guide

for the FMA device for further information.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG Mode of Operation Overview (Cont.)

While the TV is in FTG Mode:

• Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu

items will be read-only.

• Any FTG conﬁguration changes must be made using either the FTG File Manager (FTG Mode via CPU) or

the FTG Device Conﬁguration Application (FTG Mode via EBL). FTG Channel Map Conﬁguration and FTG

Installer Menu Conﬁguration Utilities enable you to make changes, respectively, to the FTG Channel Map

and FTG Installer Menu settings as necessary. Based on the initial method used to conﬁgure the TV for

FTG Mode operation (via CPU or EBL), all subsequent changes must be transferred to either the TV CPU

or the EBL via a process that is in accordance or compatible with that method (see information on local

conﬁguration in this document or refer to documentation for the head end device/server for information on

remote management).

• If it becomes necessary to restore the TV to Pass-through Mode, there are several options that will enable

you to do so. Refer to Reference section, “Restoring Factory Defaults on the TV(s),” for further information.

Pages 45 to 48 provide overviews of the utilities that comprise the FTG File Manager. Refer to the Free-

To-Guest (FTG) File Manager User Guide for further information on the FTG File Manager. Refer to the

Free-To-Guest (FTG) Device Configuration Application User Guide for information on the FTG

Device Configuration Application.

Determining the TV Operating Mode

To determine the operating mode of the TV, press MENU SETTINGS on the Installer Remote. The menu

displayed depends on the operating mode. See examples below.

If the Function Menu appears, the TV is in a mode (FTG, PPV, etc.) that does not allow the end user to

change the fundamental TV setup. If the TV setup menus appear, the TV is in Pass-through Mode.

ASPECT RATIO

Move

Function Menu

16:9

ABC

Indicates the TV is not in Pass-through

Mode. While the TV is in this mode,

Installer Menu settings can be

accessed as read-only.

Just Scan

Set By Program

4:3

Zoom

TV Setup Menus

TIME

PICTURE

Shows that the TV is in

AUDIO

CHANNEL

INPUT

Pass-through Mode.

LOCK

OPTION

SmartShare

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG Mode via CPU

Creating an FTG Conﬁguration File using the FTG File Manager

This section describes how to create an FTG Conﬁguration (.tlx) ﬁle that can be saved to a USB memory

device. In order to enable Pro:Idiom decryption, it is recommended that you create an FTG Conﬁguration

ﬁle using the FTG File Manager.

Notes: • FTG File Manager software is available online at: www.LGsolutions.com/ftgsoftware.

• There is also an option to save (Learn) FTG Conﬁguration from a TV, which may be desirable

or required in either of the following situations:

− If you want to save customized TV setup menu settings to the FTG Conﬁguration ﬁle (in

addition to the FTG Channel Map and FTG Installer Menu settings).

− If you do not know the RF channels at the site.

See “Learning FTG Conﬁguration from a TV” on page 43 for further information. However, if

you use this option to save an FTG Conﬁguration ﬁle, it is still highly recommended that you

open the saved FTG Conﬁguration ﬁle in the FTG File Manager to verify the ﬁle contents/

settings and to enable Pro:Idiom decryption by marking Encrypted channels using the FTG

Channel Map Editor.

The procedure below provides an overview of the steps required to create an FTG Configuration (.tlx)

file. Refer to the Free-To-Guest (FTG) File Manager User Guide for further information. See also FTG

File Manager sample screens on pages 45 to 48.

1. Install (if necessary) and launch the FTG File Manager (v1.0.0 or higher) on the PC that will be used

to create the FTG Configuration (.tlx) file.

2. You have a number of options:

• To view and/or base a new FTG Conﬁguration ﬁle on an existing FTG Conﬁguration (.tlx) ﬁle, click

the Open button in the TLX File command section of the FTG File Manager main screen, and select

the desired (.tlx) file.

A list of the file’s contents will be displayed in the TLX File Contents window. Either double-click on an

individual item to copy it or click the Copy All button directly above the TLX File Contents window to

automatically copy all the contents of the opened .tlx file to the FTG Configuration List and, if

applicable, TV Setup Menu List. Note, though, that while TV setup menu settings can be included in

the new FTG Configuration file, the TV setup menu settings are not available for editing.

Edit the configuration of the items in the FTG Configuration List as well as the FTG Configuration

List itself and/or the TV Setup Menu List, as necessary, to create a new file. Then, proceed to step 3

when you are ready to continue.

• To open an existing FTG Conﬁguration (.rml) ﬁle created in the FTG Device Conﬁguration Application

to use its FTG Channel Map and/or FTG Installer Menu settings, click File and then Open from the

FTG File Manager menu bar, and select/double-click on the desired “.rml” ﬁle.

Edit the channels and/or settings as necessary, and then proceed to step 3 when you are ready to

continue.

• Create a new FTG Channel Map using the FTG Channel Map Editor in the FTG Channel Map

Conﬁguration Utility. Up to 600 logical channels (combined total of both RF and IP mapped channels)

can be defined in the FTG Channel Map.

When you are ready to continue, click Conﬁgure and then FTG File Manager from the FTG File

Manager menu bar to return to the FTG File Manager main screen, and then proceed to step 3.

(Continued on next page)

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG Mode via CPU (Cont.)

(Continued from previous page)

Note: To remove an individual item from the FTG Configuration List or the TV Setup Menu List, click on/

highlight the item to be removed, and then click the Remove Item button directly above the applicable

“List” window. To clear both the current FTG Configuration List and TV Setup Menu List contents, click

the Clear button in the List command section of the FTG File Manager main screen.

Note: To clear the current TLX File Contents, click the New button in the TLX File command section of

the FTG File Manager main screen (above the TLX File Contents window).

3. To add an FTG Channel Map to the FTG Configuration List, click

under FTG Channel Map. This

will copy the current mapped RF and IP channels to the FTG Configuration List.

Note: If you make any change(s) in the FTG Channel Map Configuration Utility to the current data to

be included in the FTG Configuration List, you will need to recopy the FTG Channel Map to the FTG

Configuration List.

4. (Optional) Load default FTG Installer Menu settings for the TV:

• Click the down arrow at the right of the Chassis ﬁeld in the Installer Menu Templates section of the

FTG File Manager main screen, and select the appropriate chassis (depending on the TV type) from

the drop-down list of available models.

• Click the Load button.

• Use the FTG Installer Menu Conﬁguration Utility to modify settings, if necessary. Then, return to the

FTG File Manager main screen.

5. To add FTG Installer Menu settings to the FTG Configuration List, click

under FTG Installer Menu

Settings. This will copy the selected model settings to the FTG Conﬁguration List.

Note: If you make any change(s) in the FTG Installer Menu Configuration Utility to the current data to

be included in the FTG Configuration List, you will need to recopy the FTG Installer Menu settings to

the FTG Configuration List.

6. Click the Save button in the List command section of the FTG File Manager main screen to save the

FTG Configuration List and, if present, TV Setup Menu List contents to an FTG Configuration (.tlx) file

on the PC’s hard drive for later use.

In the Save As pop-up window, name the file, and click Save. The default folder path is C:\Program

Files\Zenith\FTG\TLX. Note that the FTG Configuration file will have a “.tlx” file extension.

Note: To remove an individual item from the FTG Conﬁguration List or the TV Setup Menu List before

saving the new ﬁle, click on/highlight the item to be removed, and then click the Remove Item button

directly above the applicable window. To clear both the current FTG Conﬁguration List and TV Setup

Menu List contents, click the Clear button in the List command section of the FTG File Manager main

screen.

7. Transfer the FTG Configuration (.tlx) file to a USB memory device, and proceed to “Teaching FTG

Configuration to a TV” on the following page to transfer the FTG Configuration file to an LT770H TV.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG Mode via CPU (Cont.)

Teaching FTG Conﬁguration to a TV

This section describes how to “Teach” an FTG Conﬁguration ﬁle from a USB memory device to a TV.

Ensure you have completed the procedure on the previous page to create the FTG Conﬁguration ﬁle

before proceeding with the steps below.

Notes: • If the TV EBL is already in FTG Mode, you cannot use this procedure to make changes to

the FTG Channel Map and FTG Installer Menu settings. You must use a direct PC-to-TV

connection as described in Reference section, “FTG Mode via EBL (Local Conﬁguration),” or

an FMA head end device to reconﬁgure the EBL.

• If the preceding condition applies, but you wish to switch the TV to FTG mode via CPU,

refer to Reference section, “Restoring Factory Defaults on the TV(s),” for further information

before proceeding.

Note: If the Automated Installation Routine Wizard appears on the

screen when you turn ON the TV, you can use the “USB Conﬁguration”

option to conﬁgure this TV, if desired (see “USB Conﬁguration” on page

14).

1. Turn ON the TV, and then plug the USB memory device that

contains the FTG Conﬁguration ﬁle into the Target LT770H TV USB

USB Download Menu

IN port.

2. Press MENU SETTINGS on the Installer Remote to display the TV

setup menus (TV is in Pass-through Mode) or the Function Menu

(TV is already in FTG Mode).

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

3. Use the arrow navigation keys to select/highlight either the Option

menu icon from the TV setup menus or the Lock menu icon from the

Function Menu. Then, press the number “7” key a total of seven times

to display the USB Download Menu.

Teach To TV (TLX)

4. Use the Up/Down arrow keys to select Teach To TV (TLX), and then

xxLT770H-UA00005.TLX

press OK.

5. Use the Up/Down arrow keys to select the FTG Conﬁguration ﬁle

you want to install, and then press OK.

Teaching status will be shown on a progress bar in a new window.

Do NOT remove the USB device until Teaching is complete. When the

Teaching process is complete, the TV will brieﬂy display a “Teaching

Completed” window and then exit the USB Download Menu.

Teach To TV

UPDATING...

6. Remove the USB memory device from the Target TV, and verify that

the FTG Configuration is resident on the Target TV.

50%

Do not unplug!

The Target TV CPU is now in FTG Mode (if it was previously in Pass-

through Mode).

Note: After the Teaching process is complete, the TV tunes according

to the Start Channel setting in the Installer Menu. If a Start Channel is

speciﬁed, the TV will tune to that channel; otherwise, the TV will tune to

the lowest logical channel in the FTG Channel Map.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG Mode via CPU (Cont.)

Learning FTG Conﬁguration from a TV

To ensure that Pro:Idiom decryption is enabled, it is recommended that you create an FTG Configuration

file using the FTG File Manager as described on pages 40 to 41. However, if necessary, this option

enables you to save (Learn) an FTG Configuration file from an LT770H TV to a USB memory device.

Notes: • The option to save (Learn) an FTG Conﬁguration ﬁle from a TV may be desirable or required

in either of the following situations:

− If you want to save customized TV setup menu settings to the FTG Conﬁguration ﬁle

(in addition to the FTG Channel Map and FTG Installer Menu settings).

− If you do not know the RF channels at the site.

• If the TV is NOT already in FTG Mode, you may need to perform some manual conﬁguration

on the TV before you start this procedure (see “Optional Manual Conﬁguration / TV Setup”

on following page).

1. Turn ON the TV, and then plug a USB memory device into the USB

USB Download Menu

IN port on the TV.

Upgrade TV Software

2. Press MENU SETTINGS on the Installer Remote to display the TV

setup menus (TV is in Pass-through Mode) or the Function Menu

(TV is already in FTG Mode).

Upgrade PTC Software

Teach To TV (TLL)

Teach To TV (TLX)

3. Use the arrow navigation keys to select/highlight either the Option

menu icon from the TV setup menus or the Lock menu icon from

the Function Menu. Then, press the number “7” key a total of seven

times to display the USB Download Menu.

Learn From TV (TLL)

Learn From TV (TLX)

4. To gain access to the Learn From TV options in the USB Down-

load Menu, key in the password used to access the Installer Menu

(Example: Press 9-8-7-6).

Learn From TV (TLX)

5. Use the Up/Down arrow keys to select Learn From TV (TLX), and

Select the ﬁle name and press OK to start

then press OK.

xxLT770H-UA00005.TLX

6. To differentiate this .tlx ﬁle from others, you can use the Up/Down

arrow keys to change the last ﬁve digits of the ﬁlename. Press OK

when you are ready to initiate Learning.

Learn From TV

UPDATING...

Learning status will be shown on a progress bar in a new window.

Do NOT remove the USB device until Learning is complete. When

the Learning process is complete, the USB Download Menu will

reappear on the screen.

25%

Do not unplug!

7. When Learning is done, press on the Installer Remote to exit the

USB Download Menu, and remove the USB memory device.

Note: It is highly recommended that you open this FTG

Configuration file in the FTG File Manager—BEFORE transferring

(Teaching) the file to any TVs—to verify FTG Channel Map and

FTG Installer Menu settings and enable Pro:Idiom decryption by

marking Encrypted channels. This will also enable you to confirm

channels and add channel attributes, labels, etc.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG Mode via CPU (Cont.)

Optional Manual Conﬁguration / TV Setup

The manual configuration procedures below should only be performed if you do not know the RF channels

at the site and need to “Learn” FTG Configuration from an LT770H TV as described on the previous page.

Ensure the TV is in Pass-through Mode before you begin.

Set Installer Menu Items

These steps provide speciﬁc instruction only on the Installer Menu items

that should be set on an LT770H TV. Refer to pages 19 to 27 for detailed

information on all Installer Menu items.

xxLT770H PTC INSTALLER MENU

CPU-CTV

000 INSTALLER SEQ

000

1. Turn ON the TV.* Then, use the Installer Remote to access the Installer

Menu (see “Accessing the Installer Menu” on page 19 for further infor-

mation).

UPN 000-000-000-000

PTC V1.00.009

ASIC D279

CPU V3.04.00

2. Set Installer Menu item 117 FACT DEFAULT to 001 and press OK on

the Installer Remote.

This clears all Installer Menu custom settings, the channel lineup, etc.

and restores the factory default settings. The value will change back

to 0 after the commercial controller (PTC) has been restored to factory

default condition. This step ensures that the TV Channel Memory will be

the active channel lineup.

Typical Installer Menu

Note: The Installer Menu header will vary

depending on the TV you are setting up.

117 FACT DEFAULT

003 BAND/AFC

000

001

3. Set Installer Menu item 003 BAND/AFC, as appropriate.

• Broadcast: Set to 000.

• HRC: Set to 002.

• IRC: Set to 003.

• CATV: Set to 001 (default).

Adjust the values for these

Installer Menu items.

4. Set any other Installer Menu items that affect your TV programming

network to the required conﬁguration. For example, enable/disable Aux

inputs, set a Start Channel, etc.

5. After you have adjusted all Installer Menu item settings as required, press

OK once on the Installer Remote to save your changes; then, press OK

again to exit the menu.

CHANNEL

Move

• Auto Tuning

Run Auto Tuning (Channel Search)

• Manual Tuning

• Channel Edit

• Channel Label

Note: In the FTG Conﬁguration ﬁle, Logical Channel numbers will automati-

cally be assigned in ascending order, starting with 0 (zero), to the Physical

Channels from the TV Channel Map.

Note: Pro:Idiom decryption for encrypted channels will not be enabled unless

you use the FTG File Manager to set the channel attributes.

1. Search for all available analog and digital channels: Use the Installer

Remote to go to the Channel Menu, select the Auto Tuning option, and

follow the on-screen instructions.

Use Channel Menu options to run

Auto Tuning and edit the channel

lineup, as necessary.

2. Use the Channel Edit option in the Channel Menu to edit the channel

lineup, as necessary, to include free to guest channels only. Add/delete

channels per your system requirements.

Once you have completed these procedures, return to “Learning FTG Conﬁguration

from a TV” on the previous page to complete the Learn sequence.

* If the Automated Installation Routine Wizard appears on the screen when you turn ON the TV, use the Up/Down arrow

keys on the Installer Remote to select Exit from the Welcome screen, and press OK to exit the wizard. Note that in this

case, you will not need to perform step 2 because the TV is already in a factory default state.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG File Manager Utilities Overview

FTG File Manager Main Screen

FTG CONFIGURATION LIST

Data to be saved in FTG

Configuration (.tlx) file.

NEW/OPEN

TLX File options.

CLEAR/SAVE

FTG Configuration

List options.

Filename of opened FTG

Configuration (.rml) file

created using FTG Device

Configuration Application.

Copy FTG Channel Map

to and from FTG

Configuration List.

Copy FTG Installer Menu

settings to and from FTG

Configuration List.

Load default FTG Installer

Menu for appropriate

LT770H chassis.

TLX FILE CONTENTS

TV SETUP MENU LIST

Data contained in opened

FTG Configuration (.tlx) file.

Data to be saved in FTG

Configuration file.

Note: The data referenced in the FTG Conﬁguration List is only a snap-

shot of the current FTG Channel Map and FTG Installer Menu settings

when copied to the list. If you make any change(s) to the current data

to be included in the FTG Conﬁguration List, you will need to recopy

Channel Map and Installer Menu settings to the FTG Conﬁguration List.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG File Manager Utilities Overview (Cont.)

FTG Channel Map Conﬁguration Utility

The FTG Channel Map Configuration Utility enables you to create, view, edit, and print a Logical

Channel Map.

PRINT MAP

EDIT/ADD MAP

Click to display a printable

FTG Channel Map Report. The

report can also be exported as

an HTML or Text file.

Click to open the FTG

Channel Map Editor to create

or edit an FTG Channel Map

(see next page).

Filename of opened FTG

Configuration (.rml) file created

using FTG Device Configuration

Application.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG File Manager Utilities Overview (Cont.)

FTG Channel Map Editor

The FTG Channel Map Editor shows a single Logical Channel’s data and the FTG Channel Map.

LOGICAL CHANNEL MAPPING

CUSTOM CHANNEL LABELS/ICONS

Enter custom labels and select icons

by name on menu or by number.

SET CHANNEL ATTRIBUTES

Check/select Encrypted, OSD,

or Blank Video.

Select a Logical Channel number. Then,

assign the RF, Major, and Minor channel

numbers to complete the mapping.

ZONE RESTRICTION

Select Zone restriction

for channel. See

Reference section, “TV

Zone Restrictions,” for

further information.

ADD

EXIT

After defining a new

Logical Channel, click to

add channel to the FTG

Channel Map.

Click to exit editor and

return to FTG Channel

Map Configuration Utility.

UPDATE

DELETE

After editing an existing

Click to remove highlighted

Logical Channel’s data,

click to commit the changes

in the FTG Channel Map.

channel from FTG Channel

Map.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

FTG File Manager Utilities Overview (Cont.)

FTG Installer Menu Conﬁguration Utility

CONFIGURATION SETTINGS

Select tabs for categories of Installer

Menu items to set up TV.

Filename of opened FTG Configuration

(.rml) file created using FTG Device

Configuration Application.

Notes:

• The Pro:Centric tab enables you to set up Pro:Centric-speciﬁc parameters. Refer to the Free-To-

Guest (FTG) File Manager User Guide for further information.

• LAN and Hospital parameters are not applicable for these TV models.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

IP Environment Setup

The IP Environment Menu enables you to set up the network features of the TV. With the exception of

Network Connection and Network Status settings, the IP Environment Menu is editable (with the Installer

Remote) only if the TV is in Pass-through Mode and read-only when the TV is not in Pass-through Mode.

Also, if you intend to create a Master TV Setup for cloning purposes (using a USB memory device / .tlx

ﬁle—see Master TV Setup procedure on pages 15 to 18), all IP Environment settings, with the exception of

Network Connection, Network Status, and Media Share Menu / TV Name settings, may be cloned.

Accessing the IP Environment Menu

1. Use the Installer Remote to access the Installer Menu

IP Environment

Move

(see “Accessing the Installer Menu” on page 19 for further

information).

• Network Connection

2. Navigate to Installer Menu item 119 DATA CHANNEL, and

• Network Status

press 2-5-3 + MENU SETTINGS to launch the IP Environment

Menu (see example at right).

• IP Stream Control

• Pro:Centric

Use the Up/Down arrow keys on the Installer Remote to select the

desired menu option and then press OK. Refer to the following

sections for information on each of the IP Environment setup

options.

• Wake On LAN

• Media Share

When you have completed your IP Environment conﬁguration

as required, press EXIT on the Installer Remote to exit the IP

Environment Menu.

Conﬁguring the Network Connection

This option launches a Network Connection wizard that guides you through the process of setting up

the TV’s wired and/or wireless network connection. Use the arrow keys on the Installer Remote to

navigate between options.

Note: If desired, you can conﬁgure both wired and wireless connections. However, note that a

wired connection is always prioritized over a wireless connection. That is, when the TV is turned

OFF and then back ON, if a LAN cable is detected between the TV and the network, the TV will

default to the wired connection. If the LAN cable is removed, the TV will then attempt to establish

the wireless connection. Whenever the LAN cable is reconnected, the TV will re-establish the

wired connection.

1. If you will use a wired network connection, connect the

Network Connection

appropriate cable between the TV and the network.

2. With the IP Environment Menu on display, use the arrow

Select the type of network.

keys on the Installer Remote to select Network Connection.

Then, press OK.

Wired

Wireless

3. In the ﬁrst Network Connection wizard window, use the arrow

keys to select the type of network—Wired or Wireless—to

conﬁgure. Then, press OK.

Connect wired network with LAN cable.

IP/DNS can be set separately.

4. Refer to the appropriate subsection below to complete the

network connection conﬁguration.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

IP Environment Setup (Cont.)

Wired Network Connection

1. The next Network Connection window will enable you to specify

the IP and DNS conﬁguration for this TV. Auto (DHCP) tabs will

be selected by default. If a DHCP server is conﬁgured and a

static conﬁguration is not required, you can simply select OK

(on the screen) and then press OK on the Installer Remote.

The DHCP server will assign an IP address and DNS server to

the TV once the TV successfully connects to the network.

Network Connection

IP Mode

Configure IP and DNS modes.

Auto (DHCP) or Static

Auto (DHCP)

IP Address

Static

Subnet Mask

Gateway

DNS Mode

Auto (DHCP)

DNS Server

Static

Otherwise, use the arrow keys to select the Static tab(s), and

specify the static conﬁguration data for both the IP and DNS

modes. When all ﬁelds are completed, select OK (on the

screen) and press OK on the Installer Remote.

Note: You can specify a static DNS server with an auto-

conﬁgured IP address but not vice versa.

Network Connection

The TV will attempt to connect to the network and you will

see a progress screen that indicates status as each network

element is conﬁrmed (see example at right). If the network

is connected successfully, a “Wired network is connected”

message will be displayed at the top of the screen and the

network conﬁguration data will be displayed in the lower half

of the screen.

Wired network is connected.

Gateway

DNS

Internet

MAC Address : AA:BB:CC:DD:EE:23 Gateway

IP Address : 10.2.3.4 DNS Server

Subnet Mask : 255.255.255.0

: 10.10.10.10

: 10.5.6.7

Complete

2. Select Complete (if not already selected), and then press OK

on the Installer Remote to exit the Network Connection wizard

and return to the IP Environment Menu.

Note: If the network connection is not successful, the progress

screen will identify the network element in which the connection

failed. Check your cabling and/or, if necessary, press on the

Installer Remote to return to the Conﬁgure IP and DNS Modes

screen to verify the conﬁguration data.

Wireless Network Connection

1. In the next Network Connection window, use the arrow keys on

the Installer Remote to select the type of wireless connection to

conﬁgure and press OK.

• AP List: Select from a list of available access points.

Network Connection

• Enter the SSID: Direct enter the SSID of an access point

whose SSID has not been enabled for broadcast (i.e., the

access point does not appear in the AP List).

Select the type of wireless network connection.

AP List

AAA

BBB

CCC

Enter the SSID

• WPS-PBC: Connect to a network via an access point that is

enabled for PBC.

DDD

EEE

WPS-PBC

WPS-PIN

Choose from APs to connect to the network.

• WPS-PIN: Complete network/PIN veriﬁcation via the

access point web interface.

Ad-hoc

• Ad-hoc: Connect to a network via a Wi-Fi device, such as a

PC, mobile phone, etc.

(Continued on next page)

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

IP Environment Setup (Cont.)

(Continued from previous page)

Note: Make sure you have the network security password/PIN available if you are attempting to

connect to a secured network.

Note: (AP List and Enter the SSID options only) As with a wired connection, a second Network

Connection window will enable you to specify the IP and DNS conﬁguration for this network

connection. Auto (DHCP) tabs will be selected by default. If a DHCP server is conﬁgured and a

static conﬁguration is not required, you can simply select OK (on the screen) and then press OK

on the Installer Remote. The DHCP server will assign an IP address and DNS server to the TV

for this network connection once the TV successfully connects to the network. Otherwise, use

the arrow keys to select the Static tab(s), and specify the static conﬁguration data for both the IP

and DNS modes. When all ﬁelds are completed, select OK (on the screen) and press OK on the

Installer Remote.

2. Follow the on-screen instructions to complete the appropriate

network conﬁguration. Use the Installer Remote navigate ﬁelds

and make entries, etc.

Network Connection

Once you have speciﬁed conﬁguration details as necessary,

Wireless network is connected.

the TV will attempt to connect to the network and you will

see a progress screen that indicates status as each network

element is conﬁrmed (see example at right). If the network is

connected successfully, a “Wireless network is connected”

message will be displayed at the top of the screen and the

network conﬁguration data will be displayed in the lower half

of the screen.

Gateway

Wireless : NetworkName

MAC Address : AA:BB:CC:DD:EE:23 Gateway

IP Address : 10.2.3.4 DNS Server

Subnet Mask : 255.255.255.0

DNS

Internet

: 10.10.10.10

: 10.5.6.7

Complete

3. Select Complete (if not already selected), and then press OK

on the Installer Remote to exit the Network Connection wizard

and return to the IP Environment Menu.

Note: If the network connection is not successful, the progress

screen will identify the network element in which the connection

failed. Check your cabling and/or, if necessary, press on the

Installer Remote to return to previous screens to verify the

conﬁguration data.

Network Status

This option enables you to check the status of the network connection.

Note: If both wired and wireless network connections were conﬁgured in a previous session

in the IP Environment Menu, and a LAN cable is connected/detected between the TV and the

network, the Network Status operation ﬁrst will attempt to connect to the network via the wired

connection. If a wired connection is not detected, the Network Status then will attempt a wireless

connection, if one has been conﬁgured. On the other hand, if, during the current session, you

conﬁgured ﬁrst a wired and then a wireless network connection, the Network Status operation

will ﬁrst attempt to connect to the network via the wireless connection (i.e., the last connection

conﬁgured).

1. With the IP Environment Menu on display, use the arrow keys on the Installer Remote to

select Network Status. Then, press OK.

(Continued on next page)

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

IP Environment Setup (Cont.)

(Continued from previous page)

The TV will display a status screen as it conﬁrms each of

the network elements, including the TV status, the gateway

status, the DNS status, and the Internet status (see example

at right). If the network is connected successfully, a “Wired/

Wireless network is connected” message will be displayed at

the top of the screen and the network conﬁguration data will be

displayed in the lower half of the screen.

Network Status

Wired network is connected.

Gateway

DNS

Internet

MAC Address : AA:BB:CC:DD:EE:23 Gateway

: 10.10.10.10

: 10.5.6.7

IP Address

: 10.2.3.4

DNS Server

Subnet Mask : 255.255.255.0

Note: If a problem is detected, the status screen will identify

the network element in which the connection failed. Check

cabling and/or conﬁguration data, as necessary. If the status

screen is still on display, you can select Try again and press

OK to recheck the network status.

Complete

2. When the status screen shows that the network is connected,

select Complete (if not already selected) and press OK on the

Installer Remote to return to the IP Environment Menu.

Note: If you cancel the status check while it is in progress, the TV

will exit both the status window and the IP Environment Menu. If

you wish to return to the IP Environment Menu while the status

check is in progress, press on the Installer Remote.

IP Stream Control

If necessary, due to an audio and/or video stream delay, IP Stream Control options enable you to

compensate for synchronization irregularities by allowing audio PTS, video PTS, and PCR offset

modiﬁcations. This menu also enables you to specify the IGMP version (2 or 3). Note that any

modiﬁcations to these settings should be performed by qualiﬁed personnel only.

1. With the IP Environment Menu on display, use the arrow keys on

the Installer Remote to select IP Stream Control. Then, press OK.

Audio PTS Offset

2. In the IP Stream Control pop-up window, use the Up/Down arrow

Video PTS Offset

keys on the Installer Remote to navigate to the appropriate ﬁeld:

Audio PTS Offset, Video PTS Offset, PCR Offset, or IGMP Version.

PCR Offset

IGMP Version

3. Use the Left/Right arrow keys to set the appropriate value for the

selected ﬁeld.

Note: Values represent offset time in milliseconds (ms) and can be

adjusted from -500 ms to +500 ms in 10 ms increments.

4. When you have completed all modiﬁcations as required, either select

Close and then press OK on the Installer Remote or press to return

to the IP Environment Menu.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

IP Environment Setup (Cont.)

Pro:Centric Setup

Pro:Centric options enable you to conﬁgure the TV with the appropriate settings to connect to the

Pro:Centric server. Use the Up/Down arrow keys on the Installer Remote to navigate between

ﬁelds.

1. With the IP Environment Menu on display, use the arrow keys on

0ff

Mode

the Installer Remote to select Pro:Centric. Then, press OK.

Media Type

Note: Options that are initially grayed out/inaccessible in the

Pro:Centric Menu are dependent upon other settings in the display.

Server IP

Port Number

For example, if “IP” is selected in the Media Type ﬁeld, the Server IP

and Port Number ﬁelds become accessible.

Data Channel

Wake On RF

2. Refer to the appropriate subsection(s) below to conﬁgure the

TV’s Pro:Centric settings to match those of the Pro:Centric server.

12AM

Wake On Time

While the Pro:Centric application (Mode) itself is an additional feature,

the appropriate Pro:Centric server conﬁguration must be completed

to enable TV E-Z Installation (splash screen, conﬁguration, and/or

ﬁrmware) data downloads and, if conﬁgured, the Pro:Centric

application download.

Note: For those ﬁelds that permit direct entry of numerical values (for

example, Server IP, Port Number, Data Channel, etc.), once you key in

the maximum number of digits allowed in the highlighted ﬁeld, the next

available ﬁeld will be highlighted.

RF Conﬁguration

1. In the Media Type ﬁeld, use the Left/Right arrow keys to select RF.

Note: If the Media Type has already been set in the Automated Installation Routine Wizard, the

speciﬁed value will be reﬂected in this ﬁeld.

2. In the Data Channel ﬁeld, either key in or use the Left/Right arrow keys to select the RF

channel number for the Data Channel of the Pro:Centric server. The Data Channel can be set

from 0 (disabled) to 135.

Note: If the Data Channel has already been set in the Installer Menu (Installer Menu item 119

DATA CHANNEL) or in the Automated Installation Routine Wizard, the speciﬁed channel will

appear in this ﬁeld. If you change the Data Channel in this menu, Installer Menu item 119 will

now show the value you entered here.

3. In the Wake On RF ﬁeld, use the Left/Right arrow keys to select On or Off, as required. The

Wake On RF feature enables the TV to receive software updates via RF while the TV is in

standby mode. If you set Wake On RF to “On,” specify the appropriate Wake On time in the

Wake On Time ﬁeld. Note that the Wake On time is based on a 12-hour clock. Ensure the AM/

PM speciﬁcation is set accordingly.

4. Once all ﬁelds are completed as required, either select Close and then press OK on the Installer

Remote or press to return to the IP Environment Menu.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

IP Environment Setup (Cont.)

IP Conﬁguration

1. In the Media Type ﬁeld, use the Left/Right arrow keys to select IP.

Note: If the Media Type has already been set in the Automated Installation Routine Wizard, the

speciﬁed value will be reﬂected in this ﬁeld.

Note: Setting the Media Type to “IP” automatically sets the Data Channel ﬁeld to “253.” You

cannot alter this setting (unless you revert Media Type to “RF”). It is not possible to direct

enter “253” in the Data Channel ﬁeld.

2. In the Server IP and Port Number ﬁelds, either key in or use the Left/Right arrow keys to

select the appropriate values for the Pro:Centric server IP address and port number.

The IP address must match the IPv4 multicast address and the port number must match the

port number that is set in the Pro:Centric server.

Note: If the server IP address and port number have already been set in the Automated

Installation Routine Wizard, the speciﬁed data will be reﬂected in these ﬁelds.

3. Once all ﬁelds are completed as required, either select Close and then press OK on the Installer

Remote or press to return to the IP Environment Menu.

Pro:Centric Application Mode Conﬁguration

1. In the Mode ﬁeld, use the Left/Right arrow keys to select the appropriate Pro:Centric Application

Mode setting—Off, FLASH, GEM, or HTML.

Note: If the Pro:Centric Mode is set to “Off,” Pro:Centric application data will not be downloaded.

Note: If the mode has already been set in the Installer Menu (Installer Menu item 098

PRO:CENTRIC) or in the Automated Installation Routine Wizard, the speciﬁed mode will be

reﬂected in this ﬁeld. If you change the mode in this menu, Installer Menu item 098 will now

reﬂect the value you selected here.

2. Once all ﬁelds are completed as required, either select Close and then press OK on the Installer

Remote or press to return to the IP Environment Menu.

Wake On LAN Setup

The Wake On LAN feature enables the TV to receive software updates and/or be powered ON

upon receipt of Wake Up Frame packets and/or Magic Packet data via the LAN. This menu option

enables you to specify Wake On LAN parameters.

1. With the IP Environment Menu on display, use the arrow keys

WOL (Wake Up Frame)

WOL (Magic Packet)

Disabled

on the Installer Remote to select Wake On LAN. Then, press OK.

2. In the Wake On LAN pop-up window, use the Up/Down arrow keys

on the Installer Remote to navigate between ﬁelds, and use the

Left/Right arrow keys to select the appropriate value—Disabled,

Update, or Power ON—for each parameter.

3. Once all ﬁelds are completed as required, either select Close and

then press OK on the Installer Remote, or press to return to the

IP Environment Menu.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

IP Environment Setup (Cont.)

Media Share Setup

Media Share allows you to enable Smart Share and Wi-Fi Screen Share options on this TV.

When enabled, the LG Smart Share feature allows guests to see data on the TV shared by

DLNA certiﬁed devices on the same network, while the Wi-Fi Screen Share feature enables data

sharing with the TV from a Wi-Fi Direct, Smart Share enabled device or screen sharing with a

Wireless Display (WiDi) capable device (for example, a laptop with Intel hardware).

Note: Wi-Fi Screen Share can only be enabled if Smart Share is enabled. See also Reference

section, “Wi-Fi Screen Share,” for additional information on the Wi-Fi Screen Share feature.

1. With the IP Environment Menu on display, use the arrow keys on

the Installer Remote to select Media Share. Then, press OK.

2. In the Media Share pop-up window, use the Up/Down arrow keys

Disabled

Edit

Smart Share

on the Installer Remote to navigate between ﬁelds, and use the

Left/Right arrow keys to select the appropriate value—Disabled

or Enabled—for each of the Smart Share and Wi-Fi Screen Share

parameters.

Wi-Fi Screen Share

[TV]207KJCZAJ740

TV Name

3. Once Smart Share is enabled, the Edit option for the TV Name

becomes accessible, and you can specify a name for this TV so

that it is easy to identify and differentiate from other TVs for which

sharing has been enabled.

To edit the TV name, use the Up/Down arrow keys to select Edit,

and then press OK. Then, use the arrow and/or number keys on

the Installer Remote to specify a name.

Note: The default name of each LT770H TV is its serial number.

Note: While Smart Share and Wi-Fi Screen Share settings are

clonable, the TV name cannot be cloned.

4. Once all ﬁelds are completed as required, either select Close and

then press OK on the Installer Remote or press to return to the

IP Environment Menu.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Jack Pack / TV Connections & Setup

Remote Jack Pack Setup

RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093

RJP AVAILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE

to 001). See Installer Menu detailed descriptions for further information.

093 RJP AVAILABLE

001

TV Connections

Make these connections ONLY after Master TV Setup and TV cloning procedures are

complete.

Refer to the figure below, and connect the RJ-45 Control cable from the RJP cable bundle to the RJP

INTERFACE port on the TV’s rear jack panel. Then, connect HDMI, RGB, and Composite Video/Audio

connectors, as applicable, for the cable bundle.

RJP INTERFACE

HDMI/DVI IN 1

Connect RJ-45 Control cable

Connect HDMI connector

from RJP cable bundle.

SERVICE ONLY

RJP

UPDATE

RESET

INTERFACE

/ DVI IN

..........

TV-LINK CFG

(ARC)

..........

OPTICAL

DIGITAL

AUDIO IN

(RGB/DVI)

AV IN

AUX LAN

RGB IN (PC)

GAME CONTROL

/MPI

RS-232C

SPEAKER

OUT(8Ω)

(SERVICE & EXT POWER)

ANTENNA/

CABLE IN

LAN

AUDIO/VIDEO IN

Connect Composite Video/Audio

connectors from RJP cable bundle.

(Composite Video on legacy RJP only.)

RGB IN (PC)

Connect RGB connector

from RJP cable bundle

(legacy RJP only).

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: Upgrading TV/PTC Software using a USB Memory Device

Checking the Software Versions

xxLT770H PTC INSTALLER MENU

You can check the software versions of the TV by

Typical Installer

accessing the Installer Menu with the Installer Remote

(see “Accessing the Installer Menu” on page 19 for

further information).

000 INSTALLER SEQ

000

UPN 000-000-000-000

PTC V1.00.009

ASIC 20E7

CPU V3.04.00

When you are finished, press OK again to exit the

Installer Menu.

PTC Version

CPU Version

Upgrading TV/PTC Software

USB Download Menu

Before you begin, note that the software upgrade ﬁles must be stored in a folder

named “LG_DTV” in the root directory of the USB memory device. Also, ensure

the USB device has been formatted with FAT format.

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

Note for TV Software Upgrade only: If the TV detects a later version of software

on the USB device, it will automatically display a dialog from which you can start the

software upgrade immediately. Otherwise, you can close the dialog, and access the

USB Download Menu as described below.

Teach To TV (TLX)

TV Software Update (Expert)

1. Turn ON the TV, and then plug the USB memory device into the USB IN port

on the TV.

2. Press MENU SETTINGS on the Installer Remote to display the TV setup

menus (TV is in Pass-through Mode) or the Function Menu (TV is not in Pass-

through Mode).

3. Use the arrow navigation keys to select/highlight either the Option menu icon from

the TV setup menus or the Lock menu icon from the Function Menu. Then, press

the number “7” key a total of seven times to display the USB Download Menu.

TV Software Update

LOGO Image Download

4. Use the Up/Down arrow keys to select Upgrade TV Software or Upgrade

PTC Software, as applicable, and press OK.

5. Select the appropriate option(s), depending on the type of upgrade:

TV Software Update (Expert)

• TV Software Upgrade: (See screen samples at right.) Select TV Software

Update from the ﬁrst TV Software Update window. In the second TV Software

Update window, select/highlight the update ﬁle to install and press OK.

[ Current TV Software Version Information ]

EPK : 03.00.00

Note: Do not select Forced Update options unless you have been speciﬁcally

instructed to do so or have previous experience with Expert Software Updates.

The following software files are found in the memory card.

Select the file you want to download to this TV

or press EXIT to cancel the update.

• PTC Software Upgrade: In the PTC Software Update window, select/highlight

EPK: 3.01.00

the update ﬁle to install and press OK.

[Forced Update Option]

Ext. MICOM

Note: The PTC Software Update window is similar to the second TV Soft-

ware Update window, though there are no Forced Update options. Current

software version information is shown at the top and update ﬁles on the USB

device are listed at the bottom of the window.

LOGO Image

xxLT770H_v3_01_RevNo100_USB

The TV will show update completion progress in a new window. Do NOT remove the USB device

until the software upgrade is complete. When a TV software upgrade is complete, the TV will reset

itself with an automatic restart. When a PTC upgrade is complete, the TV will turn OFF.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: Downloading a Splash Screen using a USB Memory Device

Splash Screen Image File Guidelines

• The splash screen image may be either a baseline (not progressive) JPEG or a

24-bit (RGB 8x8x8) BMP.

• A JPEG image should be no larger than 1 MB.

USB Download Menu

• A BMP image should be no larger than 8 MB.

Upgrade TV Software

• The ideal resolution of an image for a 32LT770H TV is 1366 x 768 pixels (HD)

or under.

Upgrade PTC Software

Teach To TV (TLL)

• The ideal resolution of an image for a 37/42/47LT770H TV is 1920 x 1080

pixels (FHD) or under.

Teach To TV (TLX)

• The image ﬁle must be stored in a folder named “LG_DTV” in the root

directory of USB memory device.

TV Software Update (Expert)

• Ensure the USB device has been formatted with FAT format.

Downloading a Splash Screen Image

1. Turn ON the TV, and then plug the USB memory device into the USB IN port

on the TV.

TV Software Update

2. Press MENU SETTINGS on the Installer Remote to display the TV setup

menus (TV is in Pass-through Mode) or the Function Menu (TV is not in Pass-

through Mode).

LOGO Image Download

3. Use the arrow navigation keys to select/highlight either the Option menu icon

from the TV setup menus or the Lock menu icon from the Function Menu.

Then, press the number “7” key a total of seven times to display the USB

Download Menu.

TV Software Update (Expert)

The following software files are found in the memory card.

Select the file you want to download to this TV

or press EXIT to cancel the update.

4. Use the Up/Down arrow keys to select Upgrade TV Software, and then press

OK.

5. Select LOGO Image Download from the ﬁrst TV Software Update window.

6. In the second TV Software Update window, use the Up/Down arrow keys to

select the image ﬁle to download, and then press OK.

The TV will show download completion progress in a new window. Do NOT

remove the USB device until the image download is complete. When the image

download is complete, the TV will reset itself with an automatic restart. Upon the

restart, you should see the new splash screen.

Splash Image 1366 x 768 ProCentric

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: Power Consumption Settings

The following tables assume that Installer Menu item 118 POWER SAVINGS is set to 003 (default) and

Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 202).

32LT770H

Power

Consumption

(Watts)

37LT770H

Power

Consumption

(Watts)

42LT770H

Power

Consumption

(Watts)

47LT770H

Power

Consumption

(Watts)

Item 099

Back Lighting

(Static)

Percent

Savings

Percent

Savings

Percent

Savings

Percent

Savings

100

45.3

43.5

41.3

40.2

39.6

38.9

37.5

34.3

31.5

28.4

25.5

0.0%

4.0%

53.6

51.6

49.1

47.8

47.2

46.3

44.9

41.7

38.3

34.4

30.5

0.0%

3.7%

62.3

59.7

56.4

54.7

53.8

52.8

50.8

46.4

42.3

37.7

33.7

0.0%

4.2%

78.0

73.8

69.0

66.3

64.7

63.3

60.3

53.5

47.3

40.6

34.7

0.0%

5.4%

8.8%

8.4%

9.5%

11.5%

15.0%

17.1%

18.8%

22.7%

31.4%

39.4%

47.9%

55.5%

11.3%

12.6%

14.1%

17.2%

24.3%

30.5%

37.3%

43.7%

10.8%

11.9%

13.6%

16.2%

22.2%

28.5%

35.8%

43.1%

12.2%

13.6%

15.2%

18.5%

25.5%

32.1%

39.5%

45.9%

32LT770H

37LT770H

42LT770H

47LT770H

Item 099

Back Lighting

(Dynamic)

Power

Consumption

(Watts)

Power

Consumption

(Watts)

Power

Consumption

(Watts)

Power

Consumption

(Watts)

Percent

Savings

Percent

Savings

Percent

Savings

Percent

Savings

200

190

180

170

160

150

140

130

120

110

101

33.4

32.3

31.4

31.0

30.7

30.4

30.2

29.0

27.6

26.1

25.6

0.0%

3.3%

6.0%

7.2%

8.1%

9.0%

9.6%

13.2%

17.4%

21.9%

23.4%

40.5

39.4

38.3

37.9

37.6

37.2

36.9

35.2

33.5

31.2

30.5

0.0%

2.7%

5.4%

6.4%

7.2%

8.1%

8.9%

13.1%

17.3%

23.0%

24.7%

44.8

43.5

42.3

41.8

41.5

40.8

40.5

38.5

36.9

34.6

33.9

0.0%

2.9%

5.6%

6.7%

7.4%

8.9%

9.6%

14.1%

17.6%

22.8%

24.3%

51.0

49.0

47.3

46.5

46.0

45.2

44.7

41.9

39.2

35.7

34.7

0.0%

3.9%

7.3%

8.8%

9.8%

11.4%

12.4%

17.8%

23.1%

30.0%

32.0%

Note: Values are results of controlled experiments under laboratory conditions.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: TV Aux Input Conﬁguration

ENABLE

MPI DATA

DATA STATUS

MPI DATA

DIRECT ACCESS

START AUX

SOURCE

ASSIGN-

MENT

STATUS TYPE

0x41 SOURCES

ENABLED (R/W)

TYPE 0xD2

CURRENT AV

SOURCE (R)

Tuning

DATA STATUS

TYPE 0x0D

AUX

Installer Menu

SOURCE (R)

OLD_

OCV = 0 OCV = 1

OLD_

Source

Input

Source

Mode

Number

Labeling

Value

Labeling

Value

Labeling

131

Video1

(Rear)

REAR_AUX_EN

0x02

Rear Video

(Aux)

Rear Video

(Aux)

0 (VIDEO)

132

133

HDMI2

DTV/PC

HDMI2 ENABLE

HDMI1 ENABLE

0x04 S-Video Rear

S-Video Rear 0 (VIDEO)

HDMI1/DVI

0x08

0x10

0x20

Front

Computer

Front

0 (VIDEO)

Computer

134

135

RGB

REAR RGB EN

HDMI3 ENABLE

SVGA Rear

Computer

SVGA Rear

Computer

(COMPUTER)

HDMI3

DTV/PC

NTSC Rear

Computer

NTSC Rear

Computer

0 (VIDEO)

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: b-LAN Setup & Overview

The b-LAN module is internal to the TV. It allows hotel/institution head end equipment with b-LAN technology

to communicate, via the institution’s RF distribution system, with the TV for configuration and control.

Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module

and the GAME CONTROL/MPI port (see note below). The default value is 003—the b-LAN module is only

powered when the TV is turned ON. See chart below.

TV Power On State

TV Standby State

POWER

SAVINGS

b-LAN & GAME

CONTROL/MPI Port

Power

b-LAN & GAME

CONTROL/MPI Port

Power

001

Off

003 (default)

A b-LAN enabled head end device, such as an LG FMA-LG101, broadcasts over the RF distribution system

to communicate to multiple TVs. When the TV is first installed, it must be turned ON in order for its embedded

b-LAN module to receive communication from the head end device. At this point, if it is desired for the b-LAN

module to always be powered, including while the TV is in Standby, set Installer Menu item 118 POWER

SAVINGS to 001.

Also, if MPI communication is required for external MPI control, set Installer Menu item 118 POWER SAVINGS

to 001 so that the GAME CONTROL/MPI port circuitry is always powered.

For specific applications, the RS-232 (DB9) port may be used to provide +12v/1A external power (for

example, to an external MPI control device). In this case, Installer Menu item 118 POWER SAVINGS must

be set to 009—both the b-LAN module and the GAME CONTROL/MPI port circuitry are always powered,

and the external power is provided on pin 9 of the RS-232 port.

Caution: POWER SAVINGS should NEVER be set to 007. This setting is intended for factory use

only.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: FTG Mode via EBL (Local Conﬁguration)

The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV

connection. Refer to the Free-To-Guest (FTG) Device Configuration Application User Guide for further

information.

Notes: • FTG Device Conﬁguration Application software is available online at: www.LGsolutions.com/

ftgsoftware.

• If the TV CPU is already in FTG Mode, you cannot use this procedure to make changes to the

FTG Channel Map and FTG Installer Menu settings. Instead, refer to and use the processes

described on pages 40 to 44 to reconﬁgure the TV CPU.

• If the preceding condition applies, but you wish to switch the TV to FTG Mode via EBL, refer

to Reference section, “Restoring Factory Defaults on the TV(s),” for further information before

proceeding.

1. Install (if necessary) and launch the FTG Device Configuration Application (v5.0.0 or higher) on the

PC that will be used to configure the EBL.

2. Build an FTG Channel Map using the FTG Channel Map Editor in the FTG Channel Map Configuration

Utility (or, if applicable, open an existing FTG Configuration [.rml] file).

Note: Up to 141 logical channels can be defined in the FTG Channel Map.

3. Connect the PC to the TV-LINK CFG jack on the TV’s rear jack panel using a USB-to-TTL serial cable

(TTL-232R-5V-AJ). If necessary, install the device driver on the PC.

4. Turn ON the TV.

Note: If Installer Menu item 118 POWER SAVINGS is set to 3 (default), the TV must be ON in order

for steps 5 and 6 below to be successful.

5. “Write” the FTG Channel Map to the EBL (switches the EBL from Pass-through Mode to FTG Mode).

Note: After a “Write” of new data, the TV will briefly display a green text banner that shows the EBL

firmware version and release date.

6. “Read” the current FTG Installer Menu settings from the EBL using the FTG Installer Menu

Configuration Utility. If necessary to make changes to Installer Menu items, “Write” them back to the

EBL in FTG Mode.

7. Save the FTG Channel Map and FTG Installer Menu settings to an FTG Configuration (.rml) file for

future use.

8. Tune the TV to a logical channel in the FTG Channel Map.

USB-to-TTL Serial Cable

SERVICE ONLY

Required for direct PC-to-TV

FTG configuration.

TV-LINK CFG

AUDIO IN

(RGB/DVI)

Laptop

AUX LAN

TV-LINK CFG

Use for direct PC-to-

TV FTG configuration.

SPEAKER

OUT(8Ω)

LAN

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: RJP Model List & Input Auto-sensing Hierarchy

RJP Legacy Models

• RJP-101M

• RJP-101ML

• RJP-110F

• RJP-110FW

• RJP-110W

• RJP-110WBR

• RJP-110S

• RJP-120G

• RJP-120T

• RJP-201B/202B

RJP Scaler Models

• RJP-201M

• RJP-301B

• RJP-401B

RJP Input Auto-sensing Hierarchy

Priority

Video

Audio

1st (Highest)

Digital Video In

Audio In (3.5mm)

2nd

3rd

PC Video In

Video In

Audio In (L/R)

Digital Video In

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: Restoring Factory Defaults on the TV(s)

This section describes how to restore factory defaults either on a single TV that is currently in Pass-through

or FTG Mode or on multiple TVs that are currently in FTG Mode.

Note: If the TV(s) is/are currently in FTG Mode, restoring the factory defaults also resets the TV(s) to

Pass-through Mode.

Installer Menu Item 117 FACT DEFAULT

If the TV is currently in Pass-through Mode, you can set Installer Menu item 117 FACT DEFAULT to 001

to restore the factory defaults and clear the channel lineup, including any assigned channel icons and

custom text labels.

Factory “IN-STOP”

If the TV is currently in FTG Mode, a predeﬁned value for Installer Menu item 117 FACT DEFAULT

enables access to initiate a factory “IN-STOP” process that will restore the TV to Pass-through Mode in

addition to restoring all factory defaults. Contact technical support for the required value for Installer Menu

item 117 and for additional information on performing the IN-STOP from the Installer Menu.

Additional FTG Mode via CPU Options

There are two additional options for restoring Pass-through Mode/factory defaults on TVs that are in FTG

Mode via the CPU. The ﬁrst enables you to restore a single TV to Pass-through Mode, while the second

enables you to restore multiple TVs to Pass-through Mode at one time. However, both options require that

you create a “Zero Mapped Channels” FTG Conﬁguration (.tlx) ﬁle, i.e., an FTG Conﬁguration ﬁle with no

data. Refer to the Free-To-Guest (FTG) File Manager User Guide for further information.

• Using a USB memory device, “Teach” a “Zero Mapped Channels” FTG Conﬁguration (.tlx) ﬁle to the TV.

Refer to “Teaching FTG Conﬁguration to a TV” on page 42 of this document for further information on the

Teaching process.

• If your system uses a Pro:Centric server for remote management/administration, use the Pro:Centric

server Admin Client to load a “Zero Mapped Channels” FTG Conﬁguration (.tlx) ﬁle on the Pro:Centric

server. Refer to the Pro:Centric Server Admin Client User Guide for further information.

Additional FTG Mode via EBL Options

There are two additional options for restoring Pass-through Mode/factory defaults on TVs that are in FTG

Mode via the EBL. The ﬁrst enables you to restore a single TV to Pass-through Mode, while the second

enables you to restore multiple TVs to Pass-through Mode at one time.

Note: While the IN-STOP process described above will clear both the PTC and the CPU, both

options below only clear the PTC. Thus, the current Channel Map and TV setup menu settings

will remain in the CPU after the reset is completed.

• Using a direct PC-to-TV connection, “Write” an unpopulated Channel Map—that is, a Channel Map with 0

(zero) channels—to the TV. Refer to Reference section, “FTG Mode via EBL (Local Conﬁguration),” and/or

the Free-To-Guest (FTG) Device Configuration Application User Guide for further information.

• If your system uses an FMA for remote management/broadcast conﬁguration, conﬁgure the FMA

device with an FMA Conﬁguration (.fma) ﬁle that only contains a “0 Mapped Channels” FTG Channel Map

to broadcast to the TV EBL(s). Refer to the Free-To-Guest (FTG) Device Configuration Application

User Guide and/or the Installation & Conﬁguration Guide for the FMA device for further information.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: TV Zone Restrictions

The FTG Channel Map Editor in the FTG File Manager’s FTG Channel Map Conﬁguration Utility enables

you to assign Zone restrictions to channels that may be deemed unsuitable for certain locations, for

example, a hotel lobby. In the FTG Channel Map Editor, a Zone # (for example, “1”) must be designated for

each channel that is to be restricted.

On location, set the Zone # for all the TVs in a select area, or “Zone” (for example, the lobby) so that the

TVs can omit channels that have been restricted in the FTG Channel Map. However, note that while a

channel can be restricted from up to eight Zones, a TV can only ever be in (set for) one Zone. TV Zone 0

is the default TV Zone #. When the TV Zone is 0, the TV will ignore any restriction that may be placed on

channels in the FTG Channel Map.

See the FTG Channel Map Editor overview on page 47. Also, see the Free-To-Guest (FTG) File Manager

User Guide for more detailed information on assigning Zone restrictions.

Use the following procedure to specify a Zone designation for a

TV. Note that the Zone can only be set while the TV is in Pass-

through Mode.

OPTION

Move

• Language

• Caption

1. Turn ON the TV.

: Off

: On

: 1

2. Press MENU SETTINGS on the Installer Remote, and use

the arrow navigation keys to select/highlight the OPTION

menu option. Then, press OK.

• Balloon Help

• Set ID

• Demo Mode

• Zone

: Off

: 0

3. Use the Up/Down arrows to select Zone, and then press OK.

4. In the Zone pop-up window, use the Left/Right arrows to

►

select the appropriate Zone number. Then, press OK.

5. Press MENU SETTINGS to return to TV viewing.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: Wi-Fi Screen Share

When the TV’s Wi-Fi Screen Share feature is enabled in the IP Environment /

Media Share Menu (see “Accessing the IP Environment Menu” and “Media

Share Setup” on pages 49 and 55, as necessary), guests have the ability to

turn ON Wi-Fi Screen Share and select a Wi-Fi Direct, Smart Share enabled

device from which to view media files (photos, videos, music, etc.) or a WiDi

capable device, whose screen can be displayed on the TV.

OPTION

Move

• Caption

: Off

: On

: 1

• Balloon Help

• Set ID

• Demo Mode

• Zone

: Off

: 0

Note: When Smart Share is enabled on the LT770H TV, regardless of

whether Wi-Fi Screen Share is also enabled, the TV Name will be displayed

in the TV menus described below. However, the TV Name is not editable

outside of the IP Environment Menu.

• TV Name

: [TV]207KJCZA9J740

• Wi-Fi Screen Share

Use the following procedure to turn ON Wi-Fi Screen Share and select a

device to which to make a connection.

(TV in Pass-through Mode)

1. Turn ON the TV, and press MENU SETTINGS on the Installer Remote to

display the TV setup menus (TV is in Pass-through Mode) or the Function

Menu (TV is not in Pass-through Mode).

SmartShare

Move

2. Use the arrow navigation keys to select/highlight either the Option menu

icon from the TV setup menus or the SmartShare menu icon from the

Function Menu. Then, press OK.

All Media

PHOTOS

MUSIC

ABC

3. Use the Up/Down arrows to select W-Fi Screen Share, and then press OK.

VIDEOS

Note: The “Wi-Fi Screen Share” menu option is only available if the Wi-Fi

Screen Share feature has been enabled in the Media Share Menu.

Extra Content

TV Name

: [TV]207KJCZA9J740

4. In the Wi-Fi Screen Share pop-up window, use the Left/Right arrow keys to

select On in the Wi-Fi Screen Share ﬁeld. This will prompt the TV to search

for all available Wi-Fi Direct, WiDi, etc. enabled wireless devices, including

mobile devices, laptops, etc. Devices found will be listed in the lower half of

the screen.

Wi-Fi Screen Share

(TV not in Pass-through Mode)

Note: If the search does not initially locate any devices, select Rescan

and press OK.

5. Use the Up/Down arrow keys to select/highlight the device with which you

Wi-Fi Screen Share

wish to share, and then press OK.

Wi-Fi Direct: Select Wi-Fi Direct device from list to initiate connection.

WiDi: Exit all On Screen Menus before using WiDi certified device to

scan and connect to TV.

6. A new pop-up window will prompt you to conﬁrm your connection request.

Select Yes and press OK to continue.

▪

Wi-Fi Screen Share

The share request will be sent to the targeted device. The user of that

device may choose to allow or not allow the share connection. Similarly,

once Wi-Fi Screen Share is turned ON, other devices may request share

connections with this TV (pop-up share requests typically appear in the

bottom right of the TV screen).

1/1

Device name

Connection

LG-P930

7. If the share request is accepted, media ﬁles may now be shared between

the device and the TV using Wi-Fi Direct, or the TV display may be used

as a second screen for a WiDi device. Select Close and press OK to exit

the Wi-Fi Screen Share window.

Rescan

8. For Wi-Fi Direct / Smart Share: To access media ﬁles/folders on the TV,

either press MENU SETTINGS and select the SmartShare menu icon or

select the Input menu icon or press the Input key on the Installer Remote

to select the Smart Share device. Then, select the desired media category

to view ﬁles.

Wi-Fi Screen Share pop-up window

display is the same whether the TV

is or is not in Pass-through Mode.

Refer to the TV’s interactive guide for further information.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: LT770H Rear and Side Jack Panels

RJP INTERFACE

Connection for Remote Jack

Pack (RJP) Control cable.

SERVICE ONLY

Restricted to service updates.

OPTICAL DIGITAL

Use for amps and home theater systems.

Note: In standby mode, this port is not enabled.

TV-LINK CFG

Use for direct PC-to-TV

FTG configuration.

AUDIO IN (RGB/DVI)

Audio connection for

RGB or DVI device.

HDMI/DVI IN

Connection for HDMI/DVI

output from external device.

SERVICE ONLY

RJP

UPDATE

RESET

INTERFACE

/ DVI IN

UPDATE

..........

TV-LINK CFG

RGB IN (PC)

Connection for RGB

output from PC.

Restricted to software

updates.

(ARC)

..........

OPTICAL

DIGITAL

AUDIO IN

(RGB/DVI)

RESET

AV IN

Initiates a hardware reset

and switches the TV to

standby.

AUX LAN

RGB IN (PC)

GAME CONTROL

AUX LAN & LAN

Use for video IP

and/or network

connections.

/MPI

ANTENNA/CABLE IN

Connect to Antenna/

CATV.

RS-232C

SPEAKER

OUT(8Ω)

(SERVICE & EXT POWER)

ANTENNA/

CABLE IN

LAN

GAME CONTROL/MPI

SPEAKER OUT (8Ω)

When the TV/EBL is in Pass-through Mode, the

MPI function enables an external MPI control

device (i.e., clone programmer, VOD/PPV STB,

etc.) to control the TV. Game Control—EBL in

LodgeNet PPV Mode only.

Connect to a pair of 8 ohm speakers.

See Reference section, “External

Speaker Setup,” for further information.

RS-232C (SERVICE) *

Typically used for downloading

software updates, etc.

Side Jack Panel

AUDIO/VIDEO IN

Connection for composite audio/

video output from external device.

USB IN 1 & 2

Insert USB memory device

for software updates, cloning

purposes, FTG Mode via

CPU configuration, picture/

music entertainment, etc., as

applicable.

* For specific applications, the RS-232 (DB9) port may be used to

provide +12v/1A external power (for example, to an external MPI

control device). In this case, Installer Menu item 118 POWER

SAVINGS must be set to 9—both the b-LAN module and the

GAME CONTROL/MPI port circuitry are always powered, and the

external power is provided on pin 9 of the RS-232 port.

HDMI

Connection for HDMI output

from external device.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: External Speaker Setup

The four-contact SPEAKER OUT jack on the LT770H rear panel provides stereo speaker level signal

outputs (left +, left -, right +, right -) for a pair of 8 ohm external speakers. Outputs are variable based

on the internal speaker volume level. Refer to the following schematic for pinout details.

Caution: Do NOT plug in a mono or stereo connector, as this may damage the TV.

EXTERNAL SPEAKER_R- (Sleeve)

EXTERNAL SPEAKER_R+ (Ring 2)

EXTERNAL SPEAKER_L- (Ring 1)

EXTERNAL SPEAKER_L+ (Tip)

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference: Installer Remote Control Typical Key Functions

The LG Installer Remote is supplied with and dedicated to operate the TV. The LG Installer Remote illustrated

below shows typical remote control functions and is provided for reference only. This Installer Remote may vary

from the Installer Remote supplied with the TV.

Q.MENU

(POWER)

Turns the TV ON or OFF

TV/DVD

Select the remote’s operating mode:

TV or DVD.

INPUT

DVD

MARK

INPUT

NUMBER Buttons (0 - 9) & DASH

Use to enter a channel or program number.

Dash is used for sub-channel numbers such

as 2-1, 2-2, etc.

Displays available input sources.

(Q. MENU/MARK options N/A for these TV

models)

.,;

abc

def

FLASHBK (FLASHBACK)

Returns to the previously tuned channel or

input.

ghi

jkl

mno

Arrows (Up/Down/Left/Right) & OK

Use to navigate on-screen menus, direct tune

channels, and adjust TV settings.

pqrs

tuv

wxyz

FLASHBK

MENU SETTINGS

Displays and removes the TV setup menus (or, if

applicable, the Function Menu).

VOLUME UP/DOWN

Increases/decreases sound level.

CHAR/NUM

PORTAL

Activates subtitles.

Displays and removes the Pro:Centric interactive

menu.

TIMER

DELETE

MUTE

VOL

TIMER

Sets the amount of time before the TV

automatically turns itself OFF.

INFO

Displays channel information.

MUTE

GUIDE

PORTAL INFO

GUIDE

Switches sound ON or OFF.

Displays and removes the Pro:Centric channel

guide/EPG.

CHANNEL/PAGE UP/DOWN

Changes channels based on channels in

the channel lineup. Moves to previous or

next screen in Pro:Centric channel guide.

(RETURN)

Returns one level to the previous menu/

display.

EXIT

Clears all on-screen displays and returns to TV

viewing.

DVD/USB buttons

Use to control DVD player or view USB

memory device content.

SETTINGS

EXIT

Color buttons access special functions

in some menus.

Accesses the AV devices connected to the

HDMI ports of the TV. Opens the SIMPLINK

Menu.

(PIP/SWAP options N/A for these TV models)

PIP

PIPCH+ PIPCH

PIP INPUT

SAP

Analog Mode: Selects MTS sound (Mono,

Stereo, or SAP). DTV Mode: Changes audio

language, if additional languages are

available.*

SWAP

SAP notes:

• If SAP is selected and no SAP is provided, sound

may not be heard on channel.

• Each analog channel may have its own SAP setting.

• Digital channels will reset to default audio language

when TV is turned Off/On.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

General Troubleshooting

Some Quick and Easy Tips for Resolving Problems

Symptom

Possible Cause(s)

Possible Solution(s)

Installation

Cannot direct enter

channel number.

(TV in Pass-through Mode) Installer

Menu item 028 CH. OVERIDE is set to

If Installer Menu item 028 CH. OVERIDE is set to 0, only

channels that are active in the TV’s channel lineup can be

0, i.e., disabled (recommended setting). selected. Set CH. OVERIDE to 1 to allow access for direct

keypad entry to all channels.

(TV in FTG Mode) The channel entered Channel access is restricted to channels included in the FTG

is not part of the FTG Channel Map.

Channel Map. If necessary, make changes to the FTG Channel

Map using the FTG File Manager or the FTG Device

Configuration Application, as appropriate.

Power

No power.

See troubleshooting flow chart on following page.

Picture Reception and Sound

No picture.

TV is turned OFF.

• Turn TV ON.

• Power failure?

Antenna/cable not connected.

Connections incorrect.

MPI not connected.

Encrypted program.

Wrong tuning band.

Audio muted.

Connect antenna/cable signal to TV.

Check connections on TV.

If applicable, connect MPI cable to MPI device.

Try another channel.

Adjust Installer Menu settings.

Normal picture,

poor or no sound.

Press MUTE or use Volume Up key to increase sound level.

Try a different channel.

Broadcast problem.

Erratic Operation

Installer Menu setup.

Wrong Installer Menu settings.

Adjust Installer Menu settings as required.

Installer Remote

Remote doesn’t work.

Remote not in TV Mode.

Not aimed at IR remote sensor.

Remote too far from IR sensor.

MPI not connected.

Use MODE key to select “TV”; puts remote into TV Mode.

Point remote at IR receiver on TV.

Move remote closer to IR receiver on TV or darken room.

If applicable, connect MPI cable to MPI device.

Remove obstructions.

IR path to TV’s receiver obstructed.

Weak batteries.

Replace batteries.

Wrong battery polarity.

Check that “+” and “-” match in battery compartment.

Dim room light.

Too much light in room.

Wrong Installer Remote.

Requires compatible Installer Remote. Contact your LG dealer.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting (Cont.)

Troubleshooting Flow Chart

Controller

Quick Check

STATUS

LED on PTC

Board

Plug into AC

Power outlet.

connected

to AC

Power?

blinking?

Yes

Bad

Cycle the power by

removing and reconnecting

the AC Power cord. Then,

observe POWER LED

on front of TV.

POWER

LED lit?

Bad Digital

Board

Bad

responded?

Yes

Press POWER on

LG Installer Remote.

Press VOLUME UP/

DOWN or MUTE key on

in-room or system

integrator-supplied remote.

Bad

turned ON?

Contact system

integrator for additional

troubleshooting

assistance.

responded?

Yes

Press VOLUME UP/

DOWN or MUTE key

on LG Installer Remote.

End

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting (Cont.)

Commercial Mode Check / FTG Operation Troubleshooting

Commercial Mode Check

Use this flowchart to determine whether the TV is currently in Commercial Mode.

Press POWER on

Installer Remote.

connected

to AC

Power?

Plug into AC

Power outlet.

TV turned

ON?

Yes

Bad

Leave the TV set ON,

and press MENU on the

Installer Remote.

On-screen

menu display

no longer

Function

on display?

TV is not in Commercial

Mode. Call Technical

Support for assistance.

Press MENU repeatedly

as if to access the

Installer Menu.

toggles?

Yes

TV is in

Commercial Mode.

FTG Operation Troubleshooting

The following table provides troubleshooting information for when the EBL is configured in the FTG Mode of operation.

Symptom

Possible Cause(s)

Solution(s)

Communication Error

(“Communications

Timeout”)

Cable(s) not connected.

TV not powered.

Check and connect communication cables.

Check/connect the TV power cord.

TV not turned ON.

TV needs to be turned ON (default setting of Installer Menu

item 118 POWER SAVINGS).

Wrong COM

(communication) port.

In the FTG Device Configuration Application, select the

correct COM port for the cable being used.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting (Cont.)

Clone Programmer Troubleshooting

Caution: If the TV is in

Reset Clone Programmer After Static Shock

LodgeNet PPV Mode (check

with the site administrator if

you are not certain), do not

connect a clone programmer

to the GAME CONTROL/MPI

port, as this will damage the

clone programmer.

After replacing exhausted batteries (LT2002 only), or if the clone programmer

behaves strangely after a static shock:

• TLL-1100A: Turn the TLL-1100A OFF and then ON.

• LT2002: Use a paper clip or similar instrument inserted through the small hole

marked RESET to activate the internal reset switch and restore normal operation.

After a reset, check the real-time clock setting. It may be necessary to set the

clone programmer clock from a TV containing the correct time.

Note: Both the Master and Target TVs must be in Pass-through Mode for cloning

purposes. See also IMPORTANT CLONING INFORMATION on page 29.

Clone Programmer

Symptom

Possible Cause(s)

Possible Solution(s)

Clone copies setup in less

than 30 seconds.

Not enough time to copy entire

TV setup.

TLL-1100A: Turn the TLL-1100A OFF and then ON.

LT2002: Press RESET on clone programmer.

Then redo Learn/Teach. (Learning usually takes about 90 seconds;

Teaching usually takes 3 to 4 minutes.)

Remote does not operate

clone programmer.

Wrong Installer Remote.

Only use an LG Installer Remote to operate clone programmer

with TV.

Clone menu does not dis-

play on TV screen, TLL-

1100A shows error mes-

sage, or LT2002 LED does

not blink.

MPI cable not connected.

TV not turned ON.

Connect MPI cable properly, and ensure good connection.

TV must be turned ON for clone programmer to work.

Install four (4) fresh AA high-quality alkaline batteries.

Ensure the TLL-1100A is fully charged or connected to AC power.

(LT2002 only) Weak batteries.

(TLL-1100A only) No charge.

Clone menu hard to read.

No time set.

Weak signal.

Connect TV to a reliable analog channel signal source.

Set time on a TV, and copy time to clone programmer.

Time not available.

Clone programmer problem.

Clone not working.

• Try a different clone programmer.

• Reset the clone programmer.

Clone scans channels

more than once.

Clone should only scan channels Ensure TV is set up correctly, and try cloning again.

once.

Master and Target TVs

Symptom

Possible Cause(s)

Possible Solution(s)

Cloning did not work.

Procedure interrupted.

Wait until procedure complete message is displayed.

Different TV models.

Cloning is only possible with identical model TVs.

Step(s) omitted or not performed. Refer to the applicable cloning procedure(s), and make sure all

tasks were performed.

(LT2002 only) Clone time

disappeared.

Batteries were removed.

Batteries must remain installed to retain time settings.

New setup not present.

Target TV not reset.

Disconnect Target TV from AC power for 15 seconds.

• After cloning operations are complete, unplug the TLL-1100A/LT2002 from the TV.

• If the TV does not display a picture (blank screen) after a few seconds, just change channels.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary of Terms

Automated Installation Routine Wizard

Lodging model TV conﬁguration wizard

that provides conﬁguration options for

Pro:Centric operation as well as an option

for using a USB memory device to conﬁg-

ure a TV for FTG Mode via CPU.

FTG Mode

Physical Channel Number

LG commercial TV mode that enables

Pro:Idiom decryption and logical channel

mapping. Implementation and TV operation

is based on the “owner” of the FTG Logical

Channel Map—the CPU or the EBL. LG’s

proprietary PC software is required for

conﬁguration.

The major channel number assigned to

represent a speciﬁc 6 MHz RF band as

speciﬁed by either the broadcast or CATV

channel plan. See CEA (formerly EIA) or

NCTA speciﬁcations for further information.

b-LAN

Pro:Centric Application

LodgeNet Interactive Corporation propri-

etary RF communication system used to

conﬁgure/control TV via RF distribution

system.

LG content delivery and communication

interface that provides interactive entertain-

ment, weather, amenities, etc. information

for end users. (Powered by Pro:Centric

server.)

Function Menu

Available via Installer Remote “MENU” key.

Indicates the TV is not in Pass-through

Mode. Restricts menu options to a subset

of the TV setup menus, allowing users to

retain functional control, while disabling

setup options.

Channel Map

Typically refers to a logical channel mapping

of physical channels. This allows digital

channels, like analog channels, to be tuned

without requiring the dash key. Also, chan-

nels (analog or digital) can be arranged in

any order that seems logical for customer

tuning/viewing.

Pro:Centric Admin Client

Web editor/content wizard provided for

service provider and customer conﬁguration

of Pro:Centric application elements.

Installer Menu

Deﬁnes commercial TV functionality based

on the parameters set.

Pro:Idiom

Zenith proprietary security software that

unlocks access to premium content to help

assure rapid, broad deployment of HDTV

and other high-value digital content.

LG Free-To-Guest (FTG)

Refers to a particular commercial mode of

operation within an LG TV. See also FTG

Mode.

Channel Lineup

Channels set in the TV memory, via Auto

Tuning/manual editing or FTG conﬁguration.

PTC

Cloning

Protocol Translator Card. The commercial

controller (microprocessor) of the com-

mercial TV.

Logical Channel Number

A number assigned to either a physical or

virtual channel number in a Logical Chan-

nel Map.

The process of capturing a Master TV

Setup and transferring it to a Target TV.

May be accomplished using either a USB

memory device (available on select mod-

els) or clone programmer.

Target TV

A TV to which a Master TV Setup will be

Major Channel Number

transferred.

Typically, the RF channel number assigned

Clone Programmer

to a digital video stream.

TV Setup Menus

An accessory device (sold separately),

such as the TLL-1100A or LT2002, used

to transfer the Master TV Setup from the

Master TV to the Target TV.

Available via Installer Remote “MENU” key

in Pass-through Mode only. Menus provide

access to setup and functional features of

the TV.

Master TV

A TV whose Channel Map and Installer

Menu and TV setup menu settings have

been conﬁgured as a Master TV Setup for

cloning purposes.

Commercial Mode

USB Memory Device

A mode of operation that provides a broad

range of commercial TV features based on

control (settings) provided by the PTC and/

or an MPI control device.

A USB ﬂash drive or USB storage device,

etc. that can be used for TV conﬁguration

purposes (typically cloning or FTG Mode

via CPU conﬁguration) or for updating TV

software.

Minor Channel Number

A sub-channel or program number as-

signed to the content embedded in the

digital video stream.

CPU

MPI

The TV’s Central Processing Unit.

Responsible for the presentation of video

and audio from content received via the

TV’s tuner or Aux inputs.

Virtual Channel Number

Multiple Protocol Interface. An MPI port

or, for some TV models, an MPI card slot

provides external control options for solu-

tion providers.

An alias (virtual) channel number provided

in the data stream, by the broadcaster, of a

digital broadcast channel to be displayed

by consumer TVs in place of the physical

channel number. The major number is the

same as the original analog channel

number and the minor number is the nth

program available in that digital video

stream.

EBL

Pass-through Mode

Embedded b-LAN module. See also b-LAN.

The TV’s factory default mode of operation.

TVs can be conﬁgured for stand-alone use

or as Master TVs for cloning purposes,

and/or TVs may be controlled externally in

this mode.

E-Z Installation

Enables splash screen image and TV

conﬁguration and ﬁrmware ﬁle downloads

to selected TV models from a Pro:Centric

server. Managed and administered via the

Pro:Centric Admin Client.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

Document Revision History / Open Source Software Notice

Document Revision History

Date

Description

September 2012

October 2012

Revision A: New document

Revision B: Automated Installation Routine Wizard, IP Environment Menu, and Wi-Fi

Screen Share updates

Product documentation is available online at: www.LGsolutions.com.

Open Source Software Notice

To obtain the source code under GPL, LGPL, MPL and other open source licenses that are contained in this product, please

visit http://opensource.lge.com. In addition to the source code, all referenced license terms, warranty disclaimers and copyright

notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering

the cost of performing such distribution (such as the cost of media, shipping and handling) upon e-mail request to opensource@

lge.com. This offer is valid for three (3) years from the date on which you purchased the product.

206-4214

Download from Www.Somanuals.com. All Manuals Search And Download.

For Customer Support/Service, please call:

1-888-865-3026

www.LGsolutions.com

Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a registered

trademark of LG Electronics Inc. Intel is a registered trademark of Intel Corporation in the

U.S. and/or other countries. b-LAN is a trademark of LodgeNet Interactive Corporation.

All other trademarks or registered trademarks are the property of their respective owners.

206-4214

Revision B

Download from Www.Somanuals.com. All Manuals Search And Download.

Lance Industries Impact Driver Torx Impact Drivers User Manual
Land Pride Lawn Aerator CA0540 User Manual
Lenovo Computer Monitor L192P User Manual
Lightolier Landscape Lighting 23MHRS User Manual
Linear Home Security System DF 31 EC User Manual
Magnavox Flat Panel Television 32MF301B User Manual
Mark Levinson Stereo Amplifier No 33H User Manual
Marmitek Universal Remote 100304 User Manual
Mattel Motorized Toy Car M8487 0920 User Manual
Maytag Clothes Dryer MD75 User Manual