TM
Amplified, Caller-ID, Call Waiting, Speaker Telephone
SPEAKER
NEWCALL
DELETE
MENU
DIAL
OK
STORE
MEMORY
MODE
R/P
FLASH
MUTE
HOLD
TO
NE
LO
A
M
P
LIF
Y
VOL
OWNER’S MANUAL
1st Edition
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
When using your Starplus45, you should always follow these basic safety pre-
cautions to reduce the risk of fire, electric shock and injury to persons.
1. Read and understand all instructions.
2. Unplug the unit from the adaptor and the telephone cord before installing
a back-up battery. Do not dispose the batteries in a fire; follow your
local code for properly disposing batteries.
3. Do not open the cabinet of the unit except for the battery cover. You may
be exposed to a dangerous voltage and cause electric shock. Opening this
product automatically voids any and all manufacturer’s warranties. If you
think that the unit is damaged or is in need of repair, please contact Krown
Manufacturing, Inc.
4. Avoid using this unit during thunderstorms: there maybe a chance of
electric shock from lightning.
5. Use only a damp cloth to clean the outside of the unit. If the unit comes in
contact with any liquid source, unplug the adaptor and the telephone cord
from the back panel before touching the unit. If the unit is damaged,
contact Krown Manufacturing, Inc.
6. The Starplus45 is designed to work with only the power source indicated
on the provided adaptor. If you are not sure about your house power
source, please consult with your electric company and contact your
Krown’s local dealer to obtain or exchange a correct adaptor to use.
7. Pressing the “amplifier” button may subject the user to dangerous
sound levels.
8. Unplug the Starplus45 from the wall outlet and contact Krown
Manufacturing, Inc. if any of the following conditions occur:
a. When the power cord is damaged or frayed
b. If liquid has been spilled into the telephone
c. If the telephone is exposed to rain or water
d. If the unit did not operate normally when following the user manual,
adjust only controls that are presented in the user’s manual. Improper
adjustment of other controls may result in damage.
e. If the product has been dropped or appears damaged.
f. If the unit exhibits a distinct change in performance.
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL SAFETY NOTES FOR
CANADIAN USERS
NOTICE:
The Canadian Department of Communications label identifies certified equip-
ment. This certification means that the equipment meets certain telecommuni-
cations network protective, operational, and safety requirements. The depart-
ment does not guarantee the equipment will operate to the user’s satisfaction.
Before installing the equipment, the user should ensure that it is permissible to
be connected to the facility of the local telecommunication company. The equip-
ment must also be installed using an acceptable method of connection. The cus-
tomer should be aware that compliance with the above conditions may not pre-
vent degradation of service in some situations. Repairs to certified equipment
should be made by an authorized Canadian maintenance facility designated by
the supplier. Any repairs or alteration made by the user to this equipment or
equipment malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connec-
tions of the power utility, telephone lines, and internal metallic water pipe sys-
tem, if present, are connected together. This precaution may be particularly
important in rural areas.
Caution: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as
soon as possible.
Notice: The LOAD NUMBER (LN) assigned to each terminal device denotes
the percentage of the total load be connected to a telephone loop which is used
by the device to prevent overloading. The termination on a loop may consist of
a any combination of devices subject only to the requirement the the sum of the
load numbers of all devices does not exceed 100
SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
INTRODUCTION
Thank you for your purchase of the Starplus45 Amplified, Caller-ID, Call Waiting, and
Speaker Telephone by Krown Manufacturing Inc. This phone is designed for the hear-
ing, or mild to severe hearing loss users. You will be able to adjust not only the volume
but you can adjust the clarity of the sound to the best quality you feel comfortable at.
The Starplus45 speaker-phone will give convenience and making hands-free telephone
communication more enjoyable. You will be able to screen all calls even before picking
up the phone or when you are on another call*.
Starplus45 is hearing aid compatible and will amplify the incoming sound to the maxi-
mum availability for a severe hearing loss user. It is designed with safety and flexibility
for your whole family to enjoy using our telephone. You will be able to switch between
automatic and manual amplification modes to protect your hearing from being exposed
to dangerous sound levels.
Please read this manual very carefully before using your Starplus45 and keep it for
future reference. Staple the sales receipt to this booklet. This will help you when you
need to contact Krown for any warranty issues or questions about your purchase.
If you have any questions about our Starplus45 this manual did not cover, please call the
Krown technical staff at 817-738-2485.
(* Caller–ID and Caller Waiting-ID are services from your local telephone company.
Please contact them for details to subscribe the service to your line.)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
PACKAGE CHECK LIST
Your Starplus-45 model comes with the following parts:
• Starplus-45 amplified, Caller-ID, Call Waiting, Speaker-phone
• Handset with coiled cord
• AC adapter
• 7 foot telephone cord
• 6 inch telephone cord for use with wall mount
• Desktop/wall base adapter
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3
STARPLUS-45 FEATURES IDENTIFICATION
4
22
20
34
7
8
30
27
15
5
6
13
24
19
13
16
14
29
11
21
3
9
25
17
12
26
28
10
33
1
2
23
31
1
2
3
4
5
6
7
8
9
Amplify button
Amplifier LED
Audio jack
Battery cover
Delete
13 Left & right arrow keys
14 Memory
15 Menu
16 Mode
17 Mute
18 OK button
19 Redial
20 New call or message
waiting light
21 Numeric keypad
22 Reset hole
23 Ring flasher
24 Ringer switch
25 Ringer tone
selector switch
26 Speaker phone button
27 Speaker phone light
28 Speaker phone volume
29 Store
Dial
Dial mode selector
Display
Flash
30 Telephone jack
31 Tone slide control
32 Voice mail waiting selector
33 Volume slide control
34 12Vdc power jack
10 Handset hook
11 Handset jack
12 Hold
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4
Setup your Starplus45
Setting up your Starplus45 includes installing backup batteries and mounting the phone.
Your Starplus45 will still operate normally in power outrages before it falls back to a
regular telephone. Replace with new batteries after each power blackout. For your safe-
ty, the Starplus45 can be used to call out with no backup batteries installed.
1. Installing backup battery
Starplus45 uses 4 AA alkaline backup batteries. Unplug the power adapter and
telephone line before installing back-up batteries.
1. Insert a coin to the cover latch. Press
toward the topside to release the battery
cover on the bottom of the unit.
2. Remove the battery compartment cover.
3. Place four AA alkaline batteries into
the compartment following the
directional marks.
FIGURE 4.1
4. Replace the cover and press down to close
the cover.
2. Desktop mounting
1. Install telephone cord to the wall outlet
and to the telephone as shown in
Figure 4.4
2. Install the handset coiled cord as shown in
Figure 4.4
FIGURE 4.2
FIGURE 4.3
3. Set the dial mode selector to P (pulse) if
you have pulse dialing (rotary). If you
have tone dialing, do not change this
switch. Manufacturer setting default is
tone dial mode.
4. Plug the AC adapter cord into the power
jack located on the topside of the
telephone. Plug the AC Adapter into a
standard 120VAC wall outlet.
5. Pick up the handset or press speaker
button and listen for a dial tone. Your
Starplus-45 is ready to use.
FIGURE 4.4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CH. 4 (CONT)
3. Wall mounting
a. Install wall mounting plate as shown in Figure 4.3
b. Take the handset hook out and flip it to reverse position as shown in Figure 4.7. It
will hold the handset when the phone is in a vertical position.
c. Use the provided 6 inch modular cord to mount the phone as shown Figure 4.8.
d. Repeat step 3 through 6 of Desktop mounting section to complete the setup.
The Starplus-45 will automatically update the current date and time from the first Caller
ID received after the setup is finished. Contact your local telephone company to activate
Caller ID service the day before. If you wish to set the TIME / DATE manually, after
setup, the telephone will beep and the display will show “SET TIME / DATE.” The
display will show, after 10 seconds, the number of calls received “MISSED -00-,
ANSWER -00-” as shown in Figure 4.5.
FIGURE 4.5
FIGURE 4.6
NOTE: When the telephone is not in use, if the line is being used by another phone, the display shows
“EXTENSION IN USE”.. on the screen and BATTERY LOW LED comes on. This means back up
batteries are either low or not fitted properly. See Figure 4.6.
4. Setting up an external signaler
Connect the external ringer device direct to the second phone jack located on the top left
side of the unit as shown in Figure 4.9.
5. Connecting to an assistive listening device
Your Starplus-45 provides an audio jack to connect direct to an assistive audio listening
device. It is not designed for a hands-free headset or a phone headset.
phone jack phone signaler
FIGURE 4.7
FIGURE 4.8
FIGURE 4.9
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 5
Operating your Starplus-45
1 MAKING AND RECEIVING CALLS
Using the handset
Using the speakerphone
MAKING A CALL
1. Pick up the handset. Listen
1. Key in desired
for the dial tone
telephone number.
2. Dial desired number. Your
conversation starts when the
other end answers your call.
3. Hang up upon completion of
the call.
2. Press DIAL (The phone will
automatically go to
speakerphone mode).
3. To hang up, press
SPEAKER key.
1. Pick up the handset and start
1. Press SPEAKER key and
start your greeting.
RECEIVING A CALL
your greeting
2. Hang up upon completion of
the call.
2. To hang up, press SPEAKER
key again.
This is the Figure for the display when using the handset.
FIGURE 5.1
FIGURE 5.2
SPEAKPHONE
You can place a call on speakerphone anytime by pressing SPEAKER during a call,
then place the handset on hook. Picking up the handset (off hook) will transfer the call
from speaker-phone to the handset. The display will show SPEAKERPHONE, and the
SPEAKER LED will light in this mode.
This is the figure for the display when using the speaker phone
FIGURE 5.3
FIGURE 5.4
Your Starplus45 comes with a LED backlight keypad and display. It will turn on auto-
matically when you are making a call. The “New Call” LED will flash to indicate a new
call was received. This LED feature is also used as a message waiting * indicator.
(*Message Waiting is a service offered by your local phone company or feature of your
internal phone system)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CH. 5 (CONT)
2. Adjusting sound levels
A. INCOMING VOICE VOLUME
By sliding the VOLUME control, you can adjust the sound level of incoming
calls up to 20 dB. by pressing “AMPLIFY” button, you can control amplification
up to 45dB.
1. Pick up the handset and press the AMPLIFY button once, the “)))” icon
appears on the top left of the display and the AMPLIFY LED will come on.
2. Slide the volume control when the other person is talking to adjust to
a comfortable level.
The amplifier feature turns off automatically when you hang up the phone. To reactivate
the amplifier, repeat the above steps. This feature is used for a household with a hearing
and hearing loss. To set up for this feature to always stay on, slide the “AMP” switch to
AUTO. (Located on the bottom of the telephone)
B. INCOMING VOICE TONE
Adjusting the tone control button will give extra amplification on the
frequencies of your hearing loss. It makes the incoming sound stream more
understandable and appear to be clearer. You may adjust the tone control as many
times as possible depending on different speakers.
1. Pick up handset and press AMPLIFY button.
2. Adjust the TONE control while the other person is talking. More high-pitched
sounds will go through if moving toward HIGH.
C. BASE SPEAKER VOLUME
Press SPK VOLUME toward “+” sign or “-” sign for more or less amplification.
It will go up to 20dB maximum. No amplify button needed.
D.RINGER VOLUME
Starplus45 will delivery a maximum ring volume up to 95dB if set at HI level.
Adjust to half level or turn off the ringer by adjusting the OFF/LO/HI position.
E. RINGER TONE
While the phone is ringing, you can adjust the ringer tone to the LO or HI
position to experience with high or low pitch ring tone.
F. CALL TIMER
When the handset is picked up or the SPEAKER button is pressed, the call
counter will begin and show the elapsed time XX-XX on the display screen.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CH. 5 (CONT)
G.LCD BACKLIGHT DISPLAY
The LCD has a back light that will turn on under the following conditions:
• Any incoming call
• Picking up the handset
• Pressing any button
NOTE: The backlight will turn off automatically 15 seconds after the last activity. The AC adapter must be plugged
into the unit to enable the BACK LIGHT.
H.ADJUSTING LCD CONTRAST
1. Press MENU to toggle the display to -3- “LCD CONTRAST”
2. Press to increase or to decrease contrast level from 0 to 9.
3. Press OK or MENU to exit. Press DELETE to abandon. The default LCD
CONTRAST level is 3.
I. SETTING DATE AND TIME
Starplus45 will adjust date and time by the first received caller ID. To set up date
and time manually:
1. Press MENU to toggle the display to “SET TIME/DATE”
2. Key in new date and time. Press OK to move between numbers. Press or
to select AM, PM.
3. Press MENU to exit, or press DELETE to abandon.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6
Using your Starplus45 Call features
1. MUTE
Press MUTE to turn off the handset microphone, allowing private conversations in the
same room without the other party hearing.
Press MUTE again to resume the conversation with the calling party.
NOTE:During the mute condition, the display will show < MIC MUTE >.
2. HOLD
1. To place a call on hold, press HOLD and placed the handset on hook. The HOLD
LED will light, the display will show < CALL ON HOLD > .
2. To begin conversation again, pick up the handset or press SPEAKER. By picking up
another phone, the hold feature will automatically reconnect.
MUSIC ON HOLD
When a call is placed on hold, a tuned melody will be generated to reassure your caller
that the call has not been disconnected.
3. FLASH
Features such as call waiting and, 3-way calling* and other can be placed by using this
feature. These features are optional services from your local telephone company.
4. REDIAL
To redial the last number dialed:
Press R/P and the display will show the latest dialed number. Press DIAL. The
Starplus45 will enter speaker-phone mode and dial the displayed number.
Pick up the handset and press R/P button, the telephone will redial the last
number dialed.
NOTES: The redial memory stores the first 32 digits of any number dialed. The number dialed will be truncated
if exceeds 32 digits.
5. MEMORY DIAL AND SPEED DIAL:
Starplus45 has three buttons reserved for speed dial emergency numbers. These three
numbers and another 100 phone numbers can be programmed into the MEMORY of
your Starplus45. Each memory location can store a maximum of 32 digits and 15 letters.
You must complete each step within 15 seconds. The default memory will be empty.
* 3-way calling is a service from your local telephone company. Please contact them for details to subscribe
the service to your line.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CH. 6 (CONT)
A.EDITING AN ENTRY
To program KROWN telephone number, 8177382485 into memory:
1. Press STORE (Display shows STORE TO ?)
2. Press MEMORY (Display shows NUMBER ?)
3. Enter the phone number 8 1 7 7 3 8 2 4 8 5 using the phone keypad
4. Press STORE or OK (Display shows NAME ?)
*Enter the name K R O W N using the numeric keypad
(5577666966)
5. Press STORE or OK, the phone will beep and the display will show STORED
If you do not want to store a name, skip step 4.
FIGURE 6.1
FIGURE 6.3
FIGURE 6.2
FIGURE 6.4
NOTE:
• To add a space before another word, press number 1 once.
• If you make a mistake while entering the number, or name. Press
to move the cursor right,
press
to move the cursor left and press DELETE to delete the letter.
• Letters are always inserted to the left of the cursor
• Always store the area code together with telephone numbers.
Table 1: using the numeric keypad to enter an name.
KEY 1st 2nd
3rd
‘
C
F
4th
(
2
3
4
5
6
S
8
Z
*
5th
)
A
D
G
J
M
7
T
9
6th
&
B
7th
,
C
F
8th
.
2
3
4
5
6
R
8
Y
*
9th
1
A
D
G
J
M
S
T
1
2
3
4
5
6
7
8
9
*
0
#
-
A
D
G
J
M
P
T
W
*
B
E
H
K
N
Q
U
X
*
E
I
H
K
N
P
U
W
*
I
L
O
R
V
Y
*
L
O
Q
V
X
*
Z
*
0
#
*
0
#
0
#
0
#
0
#
0
#
0
#
0
#
0
#
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CH. 6 (CONT)
B. EDITING AN EMERGENCY BUTTON
These emergency buttons are empty and you must choose the number for each
button. Select the number reserved for:
Hospital
Fire
Police
Follow step 1 of the above “EDITING AN ENTRY”. Press the corresponding
button for hospital, fire, police. Continue with step 3 to 5 to completely enter an
emergency number.
Press the corresponding button again to display name and number you entered.
Press mode to exit display name and number and return to main display.
C. ADDING A PAUSE TO DIAL SEQUENCE
You may wish to press R/P to insert a pause between numbers. It is used for
dialing out from a telephone switch board, or making a short cut or “Cheat-sheet”
when banking by phone or Tele-teller system.
Pressing R/P will show a “P” on the LCD to indicate a 2 second pause in the
dialing sequence. Each pause counts as one digit.
D.USING TONE SERVICES ON A PULSE (rotary) LINE
If you have pulse dial phone line and area calling a tone dial Tele-teller service,
you can send out required signals without changing the dial mode.
1. Dial the servite's main number in pulse dial mode.
2. When the service answers, press * , upper O will be displayed; or press #,
lower O will be displayed. From that point any additional numbers you dial
will be sent as tone signals.
3. After you hang up, your Starplus45 will reset the dial mode to pulse
dial automatically.
E. SPEED DIALING
*REVIEW NUMBERS FROM THE MEMORY
Press MEMORY button.
The display shows ITEM -XX-.
XX is the total memories stored in the memory. Enter the first letter of the name
(e.g “K” for KROWN): Press number 5 twice and scroll with until the name
and number you want to review shows on the display.
NOTE:
If the number is longer than 15 digits, the number will shifted to the left and pause for 1 second
automatically until the end of the number has been reached. The Starplus45 will exit display mode
automatically 15 seconds after last activity.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CH. 6 (CONT)
*DIALING NUMBERS FROM THE MEMORY
By using the handset:
Pick up the handset and follow the sequence
“REVIEW A NUMBER FROM THE MEMORY”
until the display shows the name and number that
you want to dial. Press DIAL.
By using the speakerphone: Choose the desired name in MEMORY. Press
DIAL. The phone will enter speakerphone mode
and will dial the displayed number.
*EMERGENCY DIALING
Press the corresponding button for hospital, fire, or police and press DIAL.
F. CHANGING A SPEED DIAL NUMBER
If you want to change the number stored in an emergency button or memory:
1. Press emergency button or MEMORY to display the number (If you press
MEMORY, use or to search for the number.)
2. Press OK on the number you want to change, the display shows
“NUMBER ?”. The cursor will now be on the right of the last digit.
3. Move the cursor to the number you would like to edit by using or
4. Press DELETE to erase the number. Key-in the new number by using the
numeric keypad
5. Press STORE or OK. The display will ask if you want to change name by
showing “NAME ?” for 10 seconds. The old name will be displayed with
cursor on the right of the last letter.
6. Move the cursor to the letter to be edited by using or
.
7. Press DELETE to erase the letter, then key-in the desired letter using the
numeric keypad.
8. Press STORE or OK, the new number and name will be stored into memory
followed by a beep. The display now shows “STORED”.
G.DELETING A SPEED DIAL NUMBER
1. Press speed dial button or MEMORY to display the number you want to erase.
2. Press DELETE (Display shows “DELETE ?”)
3. Press the DELETE or OK to confirm
4. Starplus45 will beep and the display shows DELETED.
H DELETING ALL MEMORY ENTRIES
1. Press MEMORY (Display shows “ITEM -XX-”).
2. Press DELETE (Display shows “CLEAR MEMORY ?”).
3. Press DELETE or OK to confirm. Starplus45 beeps and the display
shows DELETED.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CH. 6 (CONT)
6. USING CALLER ID
Caller Identification is a service offer by your local telephone company. If you are not
sure if you have this option in your telephone service contract, contact them for more
detail. Starplus-45 will automatically update date and time after receiving the first
Caller-ID call. Starplus-45 can record up to 50 missed calls, 50 answered calls, and 10
dialed number history. The oldest entry will be erased if the entry is over 50 calls or 10
dials. Starplus-45 also can display the identification of a call when you are on another
call or caller ID in Call Waiting. The identification will be displayed with CW icon to
let you know there is another call waiting on line. Contact your telephone company to
have this service installed.
A.SETTING LONG DISTANCE CODE
Long Distance Code has a default setting of 1. If you use Starplus-45 with a PBX
system you may want to change the process of dialing to start by a 9.
1. Press MENU until -1- SET LDS CODE appears. Default value for long
distance is -1-.
2. Press or to shift long distance code to 1 or 9.
3. Press OK or MENU.
NOTE:
If you do not complete the setting within 15 seconds, Starplus45 will abandon the current change and
exit the setup screen to the main display.
B. SETTING AREA CODE
Starplus45 can place a call back from the Caller ID list. You need to setup area
code for Starplus45 to dial if you choose to dial from the Caller ID list. Default for
area code is -000-.
1. Press MENU button until -000- “SET AREA CODE” appears.
2. Key a new area code.
3. Press MENU to complete.
C. DISPLAYING CALLER ID INFORMATION
To review call history, Press MODE to toggle from MISSED CALL,
ANSWERED CALL, DIALED NUMBER, and return to main menu. During
review, you can use “STORE, DELETE, DIAL” keys to store, delete, or dial a
phone number from the list.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CH. 6 (CONT)\
VIEW MISSED CALL
1. Press MODE to toggle the displayed to MISSED CALL -XX-.
2. Use the or to list the missed calls. The new missed call will be displayed
first. After all missed calls are displayed, the new-call LED stops flashing.
FIGURE 6.1
FIGURE 6.2
VIEW ANSWERED CALL
1. Press MODE to toggle the display to ANSWERED CALL -XX-.
2. Use the or to list the answered calls.
FIGURE 6.3
FIGURE 6.4
VIEW DIALED NUMBER
Starplus45 can keep last 10 dialed numbers the dialed history.
1. Press MODE to toggle the display to DIALED NUMBER -XX-.
2. Use the or to view the answered calls.
FIGURE 6.3
FIGURE 6.4
D. DELETING A CALL FROM THE CALL HISTORY
1. Press “MODE” to toggle the display from missed calls, answered calls and
dialed calls.
2. Use the or to shift the list to the number you wish to delete.
3. Press DELETE once. The display will show “DELETE ?”.
4. Press DELETE or OK to confirm Starplus45 will beep once. The display
will show “DELETED”.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CH. 6 (CONT)
E. DELETING ALL CALLS
1. Press MODE to toggle the display to MISSED CALL, ANSWERED CALL or
DIALED NUMBER to delete that list.
2. Press the DELETE once and the display will show “DELETE ALL?”
3. Press the DELETE or OK to confirm.
NOTE:
You can’t erase missed calls before it has been reviewed.
F. TRANSFERRING A CALLER ID NUMBER TO SPEED DIAL MEMORY
When a caller ID number is displayed you can transfer it to a speed dial memory
by pressing “STORE” button. Select a speed dial button or press memory to
save it to speed dial memory. Press STORE twice to save.
G. DIALING FROM THE CALLER ID LIST
The caller ID displays only seven digits of the caller is phone number if the area
code is the same with your area code stored in memory. To dial from the caller ID
list, first display the number you want to dial from previous section “displaying
caller ID information”. Press OK button to toggle between the method of dialing.
-Dial 7 digit phone number (ex: 738-2485)
-Dial long distance code with phone number (ex: 1-738-2485)
-Dial local area code with phone number (ex: 817-738-2485)
-Dial long distance code, area code, and the phone number (ex: 1- 817-738-2485)
Press DIAL to dial that number. You must setup area code and long distance code
in order for these functions to work correctly.
7. MESSAGE WAITING
If you subscribe to message waiting service from you telephone company, your phone
will inform you when you have a message. The “MSG WAITING ON” appears only 8
seconds on the display, but
icon and the message LED will flash until you retrieve
the message from the call center. You can turn this feature off if you choose not to have
voice-mail-box service from your phone company. If you use Starplus-45 in a PBX sys-
tem with message waiting features, turn the switch to ON. The message waiting feature
does not work with stutter dial tone service.
8. VIP INCOMING ALERT
When an incoming call is matched with the exact number stored in
MEMORY, the symbol VIP will be displayed. If VIP ALERT is ON, Starplus45 will
send out a beep tone to alert you to a VIP incoming call.
To set VIP ALERT ON
1. Press MENU to toggle the display “VIP ALERT ON”.
2. Press or to choose VIP ALERT ON or OFF.
3. Press OK or MENU to exit, or press DELETE or MODE to abandon.
NOTE:
If VIP ALERT is ON, the symbol ((•)) will be displayed when there is a VIP call. The default VIP alert
is ON.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CH. 6 (CONT)\
9. NAME TAGGING
When an incoming call is matched with a number stored in MEMORY, the name stored
in the MEMORY will be tagged to the incoming phone number.
CALL WAIT ID ON/OFF
1. Repeatedly press MENU until “CALL WAIT ID ON” appears.
2. Press or to choose CALL WAIT ID ON/OFF.
3. Press OK or MENU to complete the setting, or press DELETE to disregard the
setting and return to standby mode, or you can do nothing and wait for 15 seconds
to disregard the setting and return to standby mode..
NOTE:
The default CALL WAIT ID setting is ON.
10. RESETTING THE PHONE
If your Starplus45 stops working properly, use a paper clip end to insert to RESET hole
to reload the original manufacturer’s settings.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 7
TAKING CARE OF YOUR STARPLUS-45
Starplus-45 is designed for indoor use only. Do not set the unit in direct sun light. It will
damage the LCD which is not covered under the manufacturer warranty.
CLEANING:
Unplug the Starplus-45 and use only a damp cloth to clean up the outside of
the housing. Never use liquid or aerosol cleaner to spray direct to the display or
body of the phone. Keep the starplus45 from dust or moisture sources.
BATTERIES:
Replace the backup batteries once a year or after a power outage to keep
starplus-45 in good performance.
TROUBLESHOOTING:
Q: The display of my StarPlus-45 is not working.
A: Check the adapter and make sure it is plugged into the electric outlet
and the cord is plugged into the power jack of the phone.
Q: My Starplus-45 does not ring.
A: Check the ringer selector to make sure it is not in the OFF position. Adjust
the ring volume to HI or LOW for your comfort.
Q: My speed dial memory is erased.
A: The memory of the Starplus-45 is saved by the power of the phone line.
There is a power interruption at the telephone center or your Starplus-45
has been disconnected from the phone line longer than 30 minutes. It will
erase the memory of the Starplus-45.
REPAIR:
Please pack your Starplus-45 in the original shipping carton with a note
describing the problem you have and send it to:
Krown Manufacturing Inc.
ATTN: Technical Department
3408 Indale Road
Fort Worth TX 76116
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 8
SPECIFICATIONS
1
Physical dimensions:
AC Adapter
Batteries:
7” X 9.1” X 2 /8
”
12VDC 1000mA
4 AA Alkaline (not included)
1
Keypad:
1 /16” large, back-lighted, high contrast keys
95 dB
Ringer volume:
Handset:
Memory:
hearing aid compatible
50 answered calls
50 missed calls
10 dialed numbers
3 emergency speed dial buttons
RJ11 modular jacks to connect to a
standard analog phone line or compatible line.
3.5mm audio listening assistive device.
FCC approved
Connections
Approval
CHAPTER 9
Warranty
Krown Manufacturing Inc. Warrants that the StarPlus-45 sold by Krown Manufacturing is free from defects in
materials and workmanship under normal use and service for one year. This warranty is applicable only to the
original purchaser of the MTCP-106 when accompanied by a sales receipt stating the date of purchase and the
name of company from which purchased. This warranty is in lieu and excludes all other warranties, expressed
or implied, including any implied warranty of merchantability or fitness and of any obligation on the part of
Krown Manufacturing. If the StarPlus-45 shall prove to be defective, then Krown Manufacturing shall either
replace or repair the StarPlus-45 at no cost to the original purchaser within one year of the date of purchase.
During the one year period you may return the StarPlus-45 to Krown Manufacturing at the following address:
Krown Manufacturing, Inc.
3408 Indale Road
Fort Worth, Texas 76116
Shipping charges are at the customer’s expense. Please include a check or money order made out to Krown
Manufacturing in the amount of $10.00 to cover shipping and handling. This warranty does not extend to any
StarPlus-45 sold by Krown Manufacturing which has been subjected to misuse, neglect, accident, improper
application, improper installation, or any use in violation of the instruction furnished by Krown Manufacturing.
This warranty does not extend to or apply to any StarPlus which has been repaired or altered by any persons who
have not been expressly approved by Krown Manufacturing. Batteries provided with this product are not
covered under this warranty.
Krown Manufacturing shall not be liable for any special or consequential damages or for loss or expense direct-
ly or indirectly arising form use of the products or any inability to use them either separately or in combination
with other equipment or product accessories or from any other cause. This warranty is only applicable to a prod-
uct purchased through Krown Manufacturing, CompuTTY, or a Krown dealer. Other than as stated herein, there
are no other warranties whether by the sample or model, by description or quantity, whether expressed or
implied, and there are no implied warranties of fitness for a particular purpose or of merchantability.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
3408 Indale Road, Fort Worth, TX 76116
Voice/TTY: (817) 738-2485 or (817) 738-8993
Fax: (817) 738-1970, E-mail: [email protected]
ORDERS: 1-(800)-366-9950
Download from Www.Somanuals.com. All Manuals Search And Download.
|