VS-1616D HDBaseT/IR/RS-232 Card Installation Sheet
The VS-1616D HDBaseT/IR/RS-232 I/O Card mounts in one of the 16 slots on the rear of
the VS-1616D chassis. Slots are numbered from left to right and must be filled
consecutively from left to right, without leaving empty slots in between.
WARNING: An input card must only be mounted in a slot designated for input cards (slots
1 to 4 and 9 to 12) and an output card must only be mounted in a slot designated for
output cards (slots 5 to 8 and 13 to 16).
Note: We recommend you use Kramer's
BC-DGKat524, BC-DGKat623 and
C
T
R
BC-DGKat7a23 shielded twisted pair (STP) cables
L
I
N
I
N
with this input/output card.
2
3
2
I
N
S
R
I
N
O
U
T
T
E
R
E
O
N
U
W
T
O
P
O
K
U
T
N
I
L
C
O
T
U
To install an I/O card:
R
T
L
I
H
N
D
M
I
H
I
N
D
M
I
I
N
I
N
1
2
D
N
V
I
I
N
1. Power off the VS-1616D and all devices
I
D
3
4
N
L
I
D
5
6
V
I
I
N
7
8
O
D
U
V
I
T
connected to it.
O
U
T
O
U
D
1
2
V
T
I
O
3
U
T
O
U
D
L
T
4
O
5
U
T
E
T
S
T
6
N
O
I
2. Using a Phillips screwdriver, loosen the
screws at the top and bottom of the
blanking plate.
I
T
U
L
O
S
E
D
V
I
R
D
L
N
R
E
T
T
I
1
1
N
A
P
3
4
I
N
1
1
H
5
6
O
D
M
U
I
T
U
T
9
A
D
V
B
1
0
I
O
1
1
R
I
U
T
R
D
2
x
T
x
G
1
L
3
2
-
2
S
n
R
x
T
O
1
4
d
U
R
T
T
E
S
T
3
x
1
A
-
O
1
1
T
B
U
T
D
H
5
6
B
-
T
B
D
H
3. Remove the blanking plate from the slot
and store it for possible future use.
T
E
N
R
E
H
T
E
H
D
C
P
4. Remove the new card from its shipping box and anti-ESD
bag.
5. Holding the card by the lower handle, align the card with
the plastic guide rails.
6. Slide the card into the chassis until the front of the card
makes contact with the connector inside the chassis.
I
N
7. Press the card firmly into the slot until the connector
plate is flush with the rear panel of the chassis and the
connector is fully seated.
A
B
R
I
R
2
3
x
T
x
2
-
G
S
R
n
x
d
R
T
x
A
-
T
B
D
H
B
-
T
B
D
H
8. Using a Phillips screwdriver, tighten the retaining screws
at the top and bottom of the card to secure it to the
chassis.
T
E
N
R
E
H
T
E
H
D
C
P
9. Power on the VS-1616D and follow the procedure in the
V1616D User Manual (see Section 9) to configure the
VS-1616D HDBaseT/IR/RS-232 Card Installation Sheet
(P/N: 2900-300254 REV 1)
Kramer Electronics Ltd.
1
2900- 300254
Rev:
P/N:
Download from Www.Somanuals.com. All Manuals Search And Download.
|