PageScope Web Connection
Scanner Mode for IC-401
User’s Guide
INDEX
1. Using PageScope Web Connection
2. Using the Scanner Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
Foreword
Welcome
This manual describes the application and the operations of PageScope Web
Connection, which is built into the IC-401 (Image controller for
KONICA MINOLTA C350), and the scanner mode.
Trademark Acknowledgements
KONICA MINOLTA and the KONICA MINOLTA logo are trademarks of
KONICA MINOLTA HOLDINGS, INC.
PageScope is a trademark of KONICA MINOLTA BUSINESS
TECHNOLOGIES, INC.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
Ethernet is a registered trademark of Xerox Corporation.
Microsoft, Windows, and Windows NT are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other
countries.
Netscape Communications, Netscape Communications’ logo, Netscape
Navigator, Netscape Communicator, and the Netscape are trademarks of
Netscape Communications Corporation in the U.S. and other countries.
PCL is a registered trademark of Hewlett-Packard Company Limited.
PostScript is a registered trademark of Adobe Systems, Inc.
EFI, Fiery and the Fiery logo are registered trademarks of Electronics For
Imaging, Inc. in the U.S. Patent and Trademark Office and/or certain other
foreign jurisdictions.
The Electronics For Imaging logo, Fiery Scan, Fiery WebScan and Fiery
WebTools are trademarks of Electronics For Imaging, Inc.
All other product names are trademarks or registered trademarks of their
respective holders.
Copyright 2004 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
The contents of this manual are subject to change without prior notice
as a result of improvements to the product.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1.4.2 File Tab............................................................... 1-15
Mailbox .................................................................. 15
One-Touch Key Registration ............................... 26
Temporary Registration ....................................... 29
1.5 Administrator Mode ...................................... 1-31
1.5.1 System Tab ........................................................ 1-31
Preference ............................................................. 31
ROM Version ......................................................... 33
Online Assistance ................................................ 34
Maintenance ......................................................... 35
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Mailbox .................................................................. 37
1.5.3 Print Tab............................................................. 1-40
Scan Setting ......................................................... 41
Delete All One-Touch Keys .................................. 42
1.5.5 Network Tab....................................................... 1-43
Summary ............................................................... 43
LDAP Setting ........................................................ 44
2.1 Overview .......................................................... 2-2
2.1.1 Scan to E-mail ..................................................... 2-3
2.2.1 Network Protocol Settings ................................. 2-9
2.2.2 Scan Settings ...................................................... 2-9
2.3 Setup Items for Scanning ............................. 2-11
2.3.1 Entering the Setup Screen ............................... 2-11
2.3.2 Address Tab....................................................... 2-12
2.3.3 Scan Mode Tab .................................................. 2-14
2.3.4 Original Setting Tab .......................................... 2-16
2.3.5 Checking the Settings on the Destination
Device................................................................. 2-17
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
2.3.6 Registering the Scan Mode Default
2.4.1 Notified Information .......................................... 2-18
For mailbox transmission .................................... 19
2.10 Scan to Mailbox Function ............................. 2-26
2.10.3 Downloading the Image Data to the
Computer ........................................................... 2-29
2.11 Scan to FTP Server Function ....................... 2-30
2.11.1 Enabling the FTP Transfer Function................ 2-31
2.11.2 Proxy Settings ................................................... 2-31
2.11.3 Retrieving the Image Data ................................ 2-32
2.12 Internet FAX Transmission Function ........... 2-33
2.12.1 Setting the Controller........................................ 2-33
2.13 Internet FAX Reception Function ................ 2-34
2.13.1 Setting the Controller........................................ 2-34
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and
Temporary Registration Key ........................ 2-35
2.14.1 One-Touch Key Registration ............................ 2-35
When Scan to Internet FAX is selected
When Scan to E-mail is selected ........................ 45
When Scan to FTP Server is selected ................ 47
When Scan to Mailbox is selected ...................... 47
When Scan to Internet FAX is selected .............. 48
2.15 Image Data ..................................................... 2-49
2.15.1 File Format......................................................... 2-49
2.15.2 File Name ........................................................... 2-50
2.16 Hold Period of the Image Data ..................... 2-52
v
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 System Requirements
PageScope Web Connection for IC-401 is a device control utility program
provided by the HTTP server built into the IC-401 (Image controller for
KONICA MINOLTA C350). This utility can be used with a Web browser as
an interface for remotely controlling IC-401.
Note
•
In this manual, the IC-401 is also referred to as “Image Controller” or
“Printer Controller”.
1.1 System Requirements
The following items are required to use this utility.
Computer
• Software
Operating System
Windows 98/NT 4.0
Windows Me
Web Browser
Internet Explorer 4 or higher
Internet Explorer 5.5 or higher
Internet Explorer 5 or higher
Internet Explorer 6 or higher
Internet Explorer 4.5 or higher
Internet Explorer 5.1 or higher
Windows 2000
Windows XP
MacOS 9.x
MacOS X
• Ethernet
• TCP/IP protocol
KONICA MINOLTA C350
IC-401 Image Controller
Interface Kit for IC-401
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Access
1.2 Access
PageScope Web Connection can be accessed directly from a Web browser.
1. Start the Web browser.
2. In the Address bar, enter the IP address of the image controller as shown
below. Then, press the [Enter] key.
http://<IP address of the image controller>/
(Example) When the IP address of the image controller is 192.168.0.10:
http://192.168.0.10/
3. The PageScope Web Connection screen appears.
1.2.1 Operation
PageScope Web Connection operation is identical to that for Internet Web
pages. You can click a link on the Web page to jump to the link destination or
click the [Back] or [Forward] button to display the previous or next page.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Screen Configuration
1.3 Screen Configuration
The screen shown below is called the User Mode screen; all users can view
this screen. By entering an appropriate password in the “Admin Password”
box on the User Mode screen, you can enter the Administrator Mode screen.
(See p. 1-6.)
The configuration of the PageScope Web Connection screen is shown below.
Note
•
Screen images shown in this manual may differ slightly from actual
ones. In addition, specifications are subject to change without prior
notice.
•
If you wish to change the display language of PageScope Web
Connection, log into the Administrator Mode, and change the setting
using the “Preference” menu.
➀
➂
➁
➃
➄
➅
➆
➇
➀ KONICA MINOLTA Logo
Click the KONICA MINOLTA logo to jump to the following Web
site.
http://konicaminolta.net
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Screen Configuration
➁ PageScope Web Connection Logo
Click the PageScope Web Connection logo to jump to the following
Web site.
http://www.pagescope.com
➂ Status Display
The current status of the Digital Copier and the image controller is
indicated by icons and text. The message “Ready” appears when the
Digital Copier and the image controller are operating normally.
➃ Admin Password
Logs in using the Administrator Mode. (For details on the log-in
procedure in the Administrator Mode, see “Logging in Using the
Administrator Mode” on page 1-6.)
➄ Tabs
Selects the category of items to be displayed.
• System
• File
• Print
• Scan
• Network (Administrator Mode only)
For details on each tab, see the following sections.
➅ Menus
Selects the information or setup item to be displayed. The menus that
appear vary depending on the tab selection.
For details on each menu, see the following sections.
➆ Information and Setting Details
Displays the details of the selected menu.
➇ WebTools
Moves to the Fiery WebTools screen.
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Screen Configuration
1.3.1 Logging in Using the Administrator
Mode
By logging into PageScope Web Connection in the Administrator Mode, you
can configure or confirm the image controller system.
1. Enter the administrator password into the “Admin Password” box at the
upper left corner of the screen.
2. Click [Log-in] to log in using the Administrator Mode.
3. To log out, click [Log-out].
Note
•
You can change the administrator password using [Admin. Mode] on the
copier. The default value is 0000.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Screen Configuration
1.3.2 Changing the Administrator Password
You can carry out the following steps to change the administrator password.
Use the copier operation panel to make the change.
1. On the copier, press the [Utility] key.
2. Touch [Admin. Mode].
3. Input Administrator Code and touch [Enter].
4. Touch [Admin. Set] and then touch [3/4].
5. Touch [PSL Administrator Code Change].
6. Input Current Administrator Code and touch [Enter].
Note
•
The default administrator password is 0000.
7. Input New Administrator Code and touch [Enter].
8. Input Retype Administrator Code and touch [Enter].
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
1.4 User Mode
1.4.1 System Tab
On the [System] tab, information concerning the system configuration of the
Digital Copier and settings are displayed.
Summary
This screen is the initial screen that appears when you access http://<IP address
of the remote controller>/ with your Web browser. You can also display the
Summary screen by clicking the [Summary] menu on the [System] tab. The
Summary screen shows the current Digital Copier system configuration and
status.
Device Status: Shows the configuration of options installed on the
Digital Copier using graphics.
Installation Status of Options:
Shows the overview of the system configuration of the
Digital Copier.
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Detail
This screen appears when you click the [Detail] menu on the [System] tab.
Clicking a sub-menu under the [Detail] menu displays information about the
applicable unit.
Input Tray
This screen appears when you click the [Input Tray] sub-menu under the
[Detail] menu. It shows the configuration of all the paper feed trays installed
on the Digital Copier.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Output Tray
This screen appears when you click the [Output Tray] sub-menu under the
[Detail] menu. It shows the configuration of all the output trays installed on
the Digital Copier.
Tray:
Option tray name
(When Single Staple Finisher is installed)
First Tray, Elevator Tray, Third Tray
(When Folding Finisher is installed)
Elevator Tray, Saddle Tray
Capacity:
Paper:
Maximum number of A4/Letter-size sheets the tray can
hold
Tray status
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Printer HDD
This screen appears when you click the [Printer HDD] sub-menu under the
[Detail] menu. It shows the status of the hard disk installed on the Digital
Copier.
Total:
Size of the installed hard disk
Used:
Amount of hard disk space used by the system
Amount of free hard disk space
Remain:
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Consumables
This screen appears when you click the [Consumables] sub-menu under the
[Detail] menu. It shows the current status of consumables of the Digital
Copier and the option units.
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Online Assistance
This screen appears when you click the [Online Assistance] menu on the
[System] tab. It shows information concerning product support. The
information can be edited in the Administrator Mode. (See p. 1-34.)
Contact:
Contact Information Phone:
Phone number of the support contact for the product
(Blank by default)
Internet Product Help:
Support contact for the product
The URL of the product information Web site. (Blank
by default)
Corporate Web Site:
The URL of the manufacturer Web site.
Click the URL to jump to the specified Web site.
Supplies and Accessories:
Information about the contact for ordering consumables
(Blank by default)
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
1.4.2 File Tab
The [File] tab is used to manage the mailboxes in the hard disk.
Mailbox
This screen appears when you click the [Mailbox] menu on the [File] tab. It
shows a list of mailboxes in the hard disk.
Mailbox:
Hold Queue button:
Shows the Fiery Hold Queue index. Click the button to
show a list of files in the Hold Queue.
Click the index to show a list of files in the mailbox.
Note
•
Mailboxes are created in the Administrator Mode. A password is
assigned when a mailbox is created. For details on the password, check
with your administrator.
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Information on the File List Screen
File Name:
Total Pages:
Finish Time:
File Size:
Name of the file stored in the mailbox.
Total number of pages of the file
Date/Time when the file was stored in the mailbox.
File size (KB)
[< Back] button: Shows the previous page
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
1.4.3 Print Tab
The [Print] tab is used to configure the image controller.
Default Setting
This screen appears when you click the [Default Setting] menu on the [Print]
tab. Clicking a sub-menu under the [Default Setting] menu displays various
setup screens for the printer.
General Setting
This screen appears when you click the [General Setting] sub-menu under the
[Default Setting] menu. The screen is used to specify the default settings of
the paper feed tray, duplex printing, and the number of copies.
Input Tray:
From the drop-down list, select the default paper feed
tray. If the device receives a print job that does not
specify the paper feed tray, the default paper feed tray is
used.
Settings
Auto, Tray1, Tray2, Tray3, Tray4, or LCT
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Duplex:
From the drop-down list, select whether to perform
duplex printing by default. If you select duplex
printing, select whether to use long edge binding or
short edge binding. If the device receives a print job
that does not specify the duplex setting, the default
duplex setting is used.
Settings
Copies:
OFF, Left Binding, or Top Binding
Enter the default number of copies. If the device
receives a print job that does not specify the number of
copies, the default number of copies is used.
Settings
1 to 999
[Apply] button: Click the button to apply the new settings.
[Clear] button: Click the button to clear the settings that were entered
or selected.
1-18
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
PCL Setting
This screen appears when you click the [PCL Setting] sub-menu under the
[Default Setting] menu. The screen is used to set default values for various
PCL settings. If the page description language that the image controller
received is PCL, the settings of the job have precedence.
Paper Size:
Orientation:
From the drop-down list, select the default paper size.
From the drop-down list, select the default orientation
of the paper.
Settings
Portrait or Landscape
Form Length: Enter the number of lines per page.
Settings
Font Size:
Settings
Font Pitch:
5 to 128
Enter the default proportional font size (points).
4.00 to 999.75 (0.25 steps)
Enter the number of characters per inch in the
horizontal direction when printing fixed pitch font.
Settings
0.44 to 99.00 (0.01 steps)
Symbol Set:
Select the symbol set used by the font. If a symbol set
that cannot be used currently is selected, the default
symbol set is used in its place.
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Font Number: Enter the font number.
[Apply] button: Click the button to apply the new settings.
[Clear] button: Click the button to clear the settings that were entered
or selected.
1-20
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
PostScript Setting
This screen appears when you click the [PostScript] Setting sub-menu under
the [Default Setting] menu. The screen is used to set default values for various
PostScript settings. If the page description language that the image controller
received is PostScript, the settings of the job have precedence.
Convert Paper Size:
Select the setting for automatically converting between
paper sizes using the inch system and those using the
metric system.
Settings
No, Letter/11 × 17 to A4/A3, or
A4/A3 to Letter/11 × 17
Color Mode:
Select the default color mode.
CMYK or Grayscale
Settings
Default Paper Size:
Select the default paper size system.
Settings
Print Cover Page:
Select whether to print a cover page by default.
No or Yes
US or Metric
Settings
1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Allow Courier Substitution:
Select whether to automatically substitute Courier font
by default when the controller receives unsupported
font or unknown font.
Settings
No or Yes
(If you select “No”, unsupported fonts are not printed.)
Print to PostScript Error:
Select whether to print error information by default
when a PostScript error occurs.
Settings
No or Yes
1-22
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Font Information
This screen appears when you click the [Font Information] menu on the
[Print] tab. It shows a list of PCL fonts and PostScript fonts that are built into
the image controller.
PCL Font
This screen appears when you click the [PCL Font] sub-menu under the [Font
Information] menu. It shows a list of PCL fonts that are built into the image
controller.
1-23
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
PostScript Font
This screen appears when you click the [PostScript Font] sub-menu under the
[Font Information] menu. It shows a list of PostScript fonts that are built into
the image controller.
1-24
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
1.4.4 Scan Tab
The [Scan] tab is used to configure the scanner mode. (For details on the
scanner mode, see chapter 2, “ Using the Scanner Mode”.)
One-Touch Key Registration
This screen appears when you click the [One-Touch Key Registration] menu
on the [Scan] tab. You can use this screen to register the transmission
destination of the scanned data beforehand.
Index:
Click a preset index name. The destination names that
are registered in the selected index are displayed at the
lower section of the screen (one-touch list).
Index Name: Preset index names are shown in the one-touch list at
the lower section of the screen. You can change the
index name here.
(Enter up to 10 characters.)
1-26
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Transmission Method:
The transmission method for the registered destination
names is shown using icons.
: Scan to E-mail icon
: Scan to FTP Server icon
: Scan to Mailbox icon
: Internet FAX icon
[Apply] button: Click the button to register the index name that you
entered.
[Delete] button: Select the check boxes at the left of the destination
names and click this button to clear the selected
destination names from the index.
Note
•
The group registration of destination names for Scan to E-mail and
Internet FAX is valid only on [Index 8].
1-27
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Registering a New Destination
Click an unregistered box (---) in the one-touch list at the lower section of the
screen to display a registration screen for a new destination.
Click the transmission method for the recipient.
• Scan to E-mail (ꢀ p. 2-37, p. 2-43)
• Scan to FTP Server (ꢀ p. 2-39)
• Scan to Mailbox (ꢀ p. 2-41)
• Scan to Internet FAX (ꢀ p. 2-42, p. 2-43)
Click the [Cancel] button to return to the previous screen.
Changing the Setting of a Registered Destination
Click the destination name you wish to change from the one-touch list at the
lower section of the screen to display a screen used to register or change the
recipient information.
1-28
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Temporary Registration
This screen appears when you click the [Temporary Registration] menu on the
[Scan] tab. You can use this screen to register the transmission destination and
settings for the scan data used only for a single job.
Temporary Registration Name:
Click a preset name to display a setup confirmation
screen.
Transmission Method:
The transmission method of the registered destination
names is shown using icons.
: Scan to E-mail icon
: Scan to FTP Server icon
: Scan to Mailbox icon
: Internet FAX icon
[Delete] button: Select the check boxes at the left of the names and click
this button to clear the selected temporary registration
names.
Note
•
The temporary registration is cleared when the job is executed.
1-29
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 User Mode
Registering a New Setting
Clicking an unregistered box (---) on the Temporary Registration screen
display a new registration screen.
Click the transmission method.
• Scan to E-mail (ꢀ p. 2-37)
• Scan to FTP Server (ꢀ p. 2-39)
• Scan to Mailbox (ꢀ p. 2-41)
• Scan to Internet FAX (ꢀ p. 2-42)
Click the [Cancel] button to return to the previous screen.
Confirming the Setting of a Registered Destination Name
Click a name from the Temporary Registration screen to display a setup
confirmation screen.
[< Back] button: Click the button to change the settings to the entered or
selected values and return to the previous screen.
1-30
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
1.5 Administrator Mode
By logging into PageScope Web Connection in the Administrator Mode, you
can configure or confirm the image controller system.
For details on the log-in procedure in the Administrator Mode, see “Logging
in Using the Administrator Mode” on page 1-6.
1.5.1 System Tab
On the [System] tab, information concerning the system configuration of the
Digital Copier and settings are displayed.
Preference
This screen appears when you click the [Preference] menu on the [System]
tab. The screen is used to specify settings concerning the screen display.
Refresh Rate: Sets the refresh rate of PageScope Web Connection.
Settings
30 to 7200 sec.
1-31
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
Display Language:
Sets the display language of PageScope Web
Connection.
[Apply] button: Click the button to apply the new settings.
[Clear] button: Click the button to clear the settings that were entered
or selected.
1-32
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
Online Assistance
This screen appears when you click the [Online Assistance] menu on the
[System] tab. You can use the screen to enter information concerning product
support.
Contact:
Enter the support contact for the product. (Can be
changed).
Contact Information Phone:
Enter the phone number of the support contact for the
product.
Internet Product Help:
Enter the URL of the product information Web site.
Corporate Web Site:
The URL of the manufacturer Web site. (Can be
changed).
Supplies and Accessories:
Enter the contact for ordering consumables.
[Apply] button: Click the button to apply the new settings.
[Clear] button: Click the button to clear the settings that were entered
or selected.
1-34
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
Maintenance
This screen appears when you click the [Maintenance] menu on the [System]
tab. You can use the screen to restart the image controller or initialize the
settings (reset to factory default settings).
Restart
This screen appears when you click the [Restart] sub-menu under the
[Maintenance] menu. You can use the screen to restart the image controller.
Printer Controller/[Restart] button:
Restarts the image controller. Click the [Restart] button
to show a screen used to confirm whether to execute the
restart operation. Click the [Yes] button on the
confirmation screen to restart the image controller.
1-35
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
Initialize
This screen appears when you click the [Initialize] sub-menu under the
[Maintenance] menu. You can use the screen to initialize the image controller
settings (reset to factory default settings).
Printer Controller Firmware/[Restore] button:
Resets the image controller settings to factory default.
Click the [Restore] button to show a screen used to
confirm whether to execute the initialization. Click the
[Yes] button on the confirmation screen to reset the
image controller settings to factory default.
1-36
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
1.5.2 File Tab
The [File] tab is used to manage the mailboxes in the hard disk.
Mailbox
This screen appears when you click the [Mailbox] menu on the [File] tab. It
shows a list of mailboxes in the hard disk.
Note
•
The operation is similar to that of the mailboxes of the User Mode. See
“Mailbox” on page 1-15.
[Create] button: Click the button to display a screen used to create a new
mailbox.
1-37
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
Creating a Mailbox
Click the [Create] button on the mailbox list screen to show a screen used to
create a mailbox.
Up to 20 mailboxes can be created.
Mailbox Name: Enter the mailbox name.
(Enter up to 12 characters.)
Password:
Enter the password. You can also select not to use a
password.
(Enter up to 40 characters.)
Retype Password:
Re-enter the string that you entered in the “Password”
box.
[Apply] button: Click the button to apply the new settings.
[Cancel] button: Click the button to clear the settings that were entered
or selected.
1-38
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
Deleting a Mailbox
To delete a mailbox, select the mailbox you wish to delete from the mailbox
list and open the file list in the mailbox. (Enter the password as necessary.)
Click the [Delete Mailbox] button at the lower right corner of the file list
screen to delete the mailbox and return to the mailbox list screen.
Note
•
When deleting a mailbox, also delete the one-touch key registration with
the destination set to that mailbox. (The one-touch key registration is not
automatically deleted.) (See p. 1-26.)
1-39
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
1.5.3 Print Tab
The [Print] tab is used to configure the image controller.
Local Interface
This screen appears when you click the [Local Interface] menu on the [Print]
tab. The screen is used to show or set information concerning the local port.
Parallel Interface:
This setting is displayed when “Enable Parallel Port” is
selected within controller setup mode.
I/O Timeout:
Enter the wait time (second(s)) that is used to determine
the completion of the job after the data received
through the parallel port stops.
1-40
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
1.5.4 Scan Tab
The [Scan] tab is used to enter and confirm settings concerning mail
transmission and delete all one-touch keys.
Scan Setting
This screen appears when you click the [Scan Setting] menu on the [Scan] tab.
The screen is used to enter and confirm settings concerning mail transmission.
Server Name: Device name
The “server name” is added to the front of the name of
the image file created by the scan function.
(See p. 2-50.)
Scanned File Separation:
Sets whether to divide the scan data by pages when the
data exceeds the maximum size.
Settings
No or Yes
1-41
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
Maximum Number of E-mails:
Specify the maximum number of separations that is
allowed when the scan data is segmented for transmission.
(See p. 2-19.)
Settings
1 to 10
[Apply] button: Click the button to apply the new settings.
[Clear] button: Click the button to clear the settings that were entered
or selected.
Delete All One-Touch Keys
This screen appears when you click the [Delete All One-Touch Keys] menu on
the [Scan] tab. The screen is used to delete settings registered to the one-touch
keys.
Delete One-Touch Key/[Delete] button:
Click the button to delete all settings registered to the
one-touch keys.
1-42
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
1.5.5 Network Tab
The [Network] tab shows settings concerning the IC-401 network.
Summary
This screen appears when you click the [Summary] menu on the [Network]
tab. It shows a summary of the image controller interface (TCP/IP settings).
Device Type: Interface type
IP Address:
IP address of the image controller
MAC Address: MAC address of the image controller
1-43
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
LDAP Setting
This screen appears when you click the [LDAP Setting] menu on the
[Network] tab.
This screen is used to specify settings concerning LDAP search functions.
Note
•
When using LDAP search functions with Fiery, a Kerberos
authentication server (including DNS functions) must be provided.
Because DNS name resolution is required with Kerberos authentication,
the following DNS settings must be made to Fiery settings in advance.
•
•
•
•
DNS server IP address: Input the DNS server IP address.
Domain name: Input the name of the domain to which Fiery belongs.
Host name: Input the Fiery host name.
•
•
If the settings for Time Zone / Date / Time in Fiery do not match the time
settings in the LDAP server, then it may not be possible to connect to the
LDAP server.
If Internal Error=-5 is displayed when searching, this may mean that the
LDAP server is not configured correctly. If this happens, please check
LDAP server settings.
1-44
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
LDAP Function:
Use this setting to turn LDAP search on or off.
Domain Name: Input the name of the domain to which the LDAP
server belongs.
LDAP Server Name/IP Address:
Input the LDAP server address.
The initial default setting is blank.
You can input the LDAP Server Name or IP Address.
Login Name: Input the user name.
Password:
Input the password.
For LDAP authentication, care must be taken since the
password is sent on the network with cleared text.
Port Number: Enter the LDAP server port number.
The initial default setting is 389.
Search Root: Input the search start point. (ex: dc=ldapsv, dc=local)
The initial default setting is blank.
1-45
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Administrator Mode
Search Timeout:
Input a timeout value (seconds) for LDAP
communication.
The initial default setting is 15 seconds.
Max Hit of number:
Input a value that specifies the maximum number of
hits that can be accepted for LDAP search results.
The initial default setting is 30.
Expiration Rate:
LDAP search results are retained within Fiery, which
accesses the LDAP server at fixed intervals to update
information. This specifies that interval for renewal.
[Check LDAP settings] button:
Click this button to check whether the server can be
accessed (logged into) using the currently configured
settings.
[Apply] button: Click the button to apply the new settings.
[Clear] button: Click the button to clear the settings that were entered
or selected.
1-46
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Overview
2.1 Overview
The following types of scanner modes are available on the Digital Copier. Use
the appropriate type that matches your network environment and application.
• Scan to E-mail:
Sends scanned data as an attachment to an e-mail (ꢀp. 2-3)
• Scan to FTP Server:
Sends scanned data to an FTP server (ꢀp. 2-4)
• Scan to Mailbox:
Sends scanned data to the controller HDD (ꢀp. 2-5)
• Internet FAX:
Attaches the scanned data to an e-mail and sends it to a device that
supports Internet FAX (ꢀp. 2-6)
* Scanned data: Image data scanned using the Digital Copier.
Note
•
This manual does not cover the operating procedures of Fiery Remote
Scan 5. For details, see the manual that came with the controller.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Overview
2.1.2 Scan to FTP Server
• Sends the scanned image data to a specified folder on the FTP server.
• Suitable for sending high-resolution data.
• Requires a network environment with an FTP server.
• Allows you to select whether to send information indicating the storage
location of the image data by e-mail using the e-mail notification
function (See p. 2-18). (A mail server is required for using the e-mail
notification function.)
• Possible to access FTP servers on the Internet via a proxy server. (A
proxy server is required.)
FTP Server
Client PC
Mail Server
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Overview
2.1.3 Scan to Mailbox
• Sends the scanned image data to a specified folder (Mailbox) on the
controller HDD.
• Suitable for sending high-resolution data.
• Allows you to select whether to send information indicating the storage
location of the image data by e-mail using the e-mail notification
function (See p. 2-18). (A mail server is required for using the e-mail
notification function.)
Box
PC
Optional
Hard Disk
Mail Server
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Overview
2.1.4 Internet FAX
Transmission
• Attaches the scanned image data to an e-mail and sends it to a device
that supports Internet FAX.
• The image data is sent in the following format: TIFF, 200 × 200 dpi,
monochrome, A4/Letter size, with MH compression.
Note
•
When sending document data using Internet FAX, you must check
whether the receiving side is capable of receiving Internet FAX in
advance.
•
If a document larger than A4/Letter size is scanned, the document is
automatically compressed and transmitted as A4/Letter size.
Black
TIFF Format
200 × 200 dpi
Device that supports
Internet FAX
Printout
Mail Server
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Overview
Reception
• Receives e-mails sent from a device that supports Internet FAX and
prints out the data.
• The following image data can be received.
TIFF format, 200 × 200 dpi/200 × 100 dpi, monochrome, A4/Letter
size, and MH/MR/MMR compression.
Note
•
If a document larger than A4/Letter size is received, the document is
automatically compressed and printed as A4/Letter size.
Device that
supports
Internet FAX
Printout
Mail Server
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Overview
2.1.5 Environment Required for Sending
Image Data
The following environment is required to send image data (send and receive
for Internet FAX) using the scan function.
Note
•
All scan functions can only be used under a TCP/IP network
environment.
Environment
Required to
Transfer Image
Data
Environment
Required to
Receive Image
Data
Other Limitations
Mail server
Mail client
computer
An upper limit file
size may be
E-mail
specified on the
mail server.
FTP server
FTP client
computer
FTP
1
Web browser
Mailbox
None*
Mail server
—
An upper limit file
size may be
specified on the
mail server.
Internet FAX
transmission
Internet FAX
reception
—
Mail server
*1: Since the image data is transferred directly to the mailbox in the controller
HDD, servers such as the mail server are not needed.
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Controller Setup Items
2.2 Controller Setup Items
The following settings must be made on the controller side to use the scan
function.
2.2.1 Network Protocol Settings
Network communications using the TCP/IP protocol must be possible. Use
the [Setup Mode] on the controller operation panel to enter the settings. For
details on the setup items and procedure, see the Controller User Manual.
2.2.2 Scan Settings
Use the “Administration Mode” of PageScope Web Connection and the [Setup
Mode] on the controller operation panel to enter the settings. For details on
PageScope Web Connection, see chapter 1, “ Using PageScope Web
Connection”.
PageScope Web
Connection
Scan to
E-mail
Scan to
FTP
Scan to
Mailbox
Internet
FAX
Administration Mode: [Scan] tab
Server Name
{*
{*
—
{*
—
{*
—
Scanned File Separation
{
{
Maximum Number of
E-mails
—
—
—
Administration Mode: [Network] tab
LDAP Setting
z
z
z
z
{: required, —: Not required, z: Required depending on the environment
*: Check the settings.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Controller Setup Items
Controller
Operation Panel
Scan to
E-mail
Scan to
FTP
Scan to
Mailbox
Internet
FAX
Setup Mode: [Service Setup]
Enable Mailbox Password
—
—
{
—
Setup Mode: [Network Setup] — [Service Setup] — [FTP Setup]
Enable FTP Services
Enable Proxy Setup
—
—
—
—
—
—
—
{
z
z
z
z
z
z
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Proxy Server IP Address
Proxy Server Port Number
Proxy Server Timeout
Proxy Server User Name
Proxy Server User
Password
Setup Mode: [Network Setup] — [Service Setup] — [E-Mail Setup]
Enable E-mail Services
Enable Print Via E-mail
Outgoing Server
{
—
{
—
—
—
—
—
—
—
—
—
—
—
—
—
—
{
{
{
{
{
Incoming Server
Server Type
1
1
Fiery Email User Name
z*
z*
1
1
—
—
Fiery Email Domain Name
Account Name
z*
z*
{
{
—
—
—
—
—
—
—
—
Password
2
2
Administrator Email User
Name
z*
z*
2
2
Administrator Email
Domain Name
—
—
z*
z*
Timeout (Sec)
{
—
—
—
—
—
—
{
{
—
Polling Interval
—
Maximum Scan File Size
{
{: required, z: Required depending on the environment, —: Not required
*1: The sender (From) address is Fiery Email User Name@Fiery Email Domain
Name. (See p. 2-20.)
*2: Administrator Email User Name@Administrator Email Domain Name is the error
notification destination if the mail does not reach the recipient for some reason.
(See p. 2-20.) However, if the mail is not transmitted, the error is not notified.
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Setup Items for Scanning
2.3 Setup Items for Scanning
When transferring image data using the scan function, the following items can
be entered on the copier operation panel.
2.3.1 Entering the Setup Screen
1. Press the [Scan] key.
2. Touch the desired tab from [Address], [Scan Mode], [Original Setting],
and [MISC].
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Setup Items for Scanning
2.3.2 Address Tab
You can specify the transmission destination of the image data.
[Temp. Registration]:
Key registered using [Temp Registration] on
PageScope Web Connection. After the scanning is
complete, the key is automatically cleared.
[Index]:
Touch Index to show the key registered using [One
Touch Key Registration] on PageScope Web
Connection.
[Address Input]:
When transferring image data using e-mail or Internet
FAX, you can send the data by directly entering the
mail address. (One address only)
Note
•
Multiple transmission destinations can be specified for mail
transmission and Internet FAX. You can specify up to 50 addresses
using up to 1800 characters.
In addition, addresses can be specified using the one-touch key and
address entry (one address entry only) simultaneously.
[MISC]:
When transferring image files using “Scan to FTP
Server” or “Scan to Mailbox”, you can select the e-mail
notification destination (see p. 2-18) from the registered
one-touch keys.
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Setup Items for Scanning
Note
•
The [Notification Address] that is selected under the [MISC] tab has
priority over [Notification Address] that is registered to the one-touch
key.
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Setup Items for Scanning
2.3.3 Scan Mode Tab
You can specify the transmission method of the document.
[Color/File]:
Specifies the color mode, data format, and compression
method.
Settings
Color mode
File Format
: Full Color, Grayscale, or Black
: PDF, TIFF, or JPEG
Note
•
If the transmission destination is set to a mailbox, the file format is
specified when the data is downloaded from the mailbox to the
computer. You do not have to set the format using [File Format] on
this screen.
Compression Level : High Quality, Standard, or High Compression
Note
•
If [Color Mode] is set to [Black], [Compression Level] does not
appear.
[Resolution]: Specifies the resolution.
Settings
200 dpi, 300 dpi, 400 dpi, 600 dpi
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Setup Items for Scanning
[Background Removal]:
Enter settings concerning background remove and
document brightness.
Background Removal Enter settings concerning background remove.
Settings
Auto or manual (-5 (maximum removal) to
+2 (minimum removal): 8 levels)
Brightness
Specify the brightness of the document.
Settings
-3 (brightest) to +3 (darkest): 7 levels
[Scan Size]:
Specify the scan size of the document.
You can also specify an arbitrary size (in unit of
millimeter or 1/16 inch).
In addition, you can also specify the erase position and
erase width.
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Setup Items for Scanning
2.3.4 Original Setting Tab
You can specify the document type.
[Document Mode]: Specify the document scan mode.
Settings
[Margin]:
1, 2 or Book Copy
Specify the direction of the margin of the
document for duplex printing.
Settings
left binding or top binding
[Original Direction]: Specify the image direction with the document set
in the tray.
Settings
Not selected (auto detection),
Portrait document Wide/Tall,
Landscape Wide/Tall,
Note
•
If an image data that results from scanning a document larger than
A4/Letter size is displayed on the computer, it is displayed as a
portrait image.
[Mixed Original]:
To scan documents of different sizes, select the
[Mixed Original] key.
[Separate Scan]:
If “Separate Scan” is selected, the following data
is handled as a single job: the data that is scanned
until the [Finish] key that appears on the control
operation panel after the scan operation complete
is selected.
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Setup Items for Scanning
2.3.5 Checking the Settings on the
Destination Device
Press the [Check] button to view the settings on the destination device.
2.3.6 Registering the Scan Mode Default
Settings
You can arbitrary specify the default settings of the Scan Mode.
1. Press the [Scan] key on the copier operation panel to enter the Scan
Mode.
2. Select the setting to make the default value in the Scan Mode.
3. Press the [Utility] key.
4. Touch [Store].
5. Touch [Reset Mode].
6. Touch [Current Mode].
7. Touch [Enter].
You can set the default settings of the Scan Mode to factory default by
touching [Factory Default].
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 E-Mail Notification
2.4 E-Mail Notification
information indicating the storage location of the image data that the scan
function created. The image data is not attached to the mail. The side
receiving the mail can refer to the information written in the mail text to
access the storage location of the image data.
When transmitting image data by selecting a one-touch key (see p. 2-35) that
has server transmission or mailbox registered and a Notification Address is set
to the selected one-touch key, an e-mail notification is transmitted. You can
also specify Notification Address on the operation panel of the copier. (See p.
2-12.)
Note
•
Mails that are transmitted by the e-mail notification function are
transmitted according to the mail transmission settings. You must set the
mail transmission settings to use the e-mail notification function.
2.4.1 Notified Information
The following information is notified by mail.
For server transmission
• IP address of the FTP server
• Directory in which the image data is saved
• File name of the image data
Note
•
You may need to enter a user name and a password to access the FTP
server.
•
The user name and password are not notified by mail.
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 URL Notification
For mailbox transmission
• http://IP address of the controller
• Mailbox name
• File name of the image data
Note
•
•
You may need to enter a password to access the mailbox.
The password is not notified by mail.
2.5 URL Notification
The URL notification function is used to notify using an e-mail the URL
indicating the storage location of the image data that the scan function created.
The image data is not attached to the URL notification mail. The side
receiving the URL notification mail can double-click the URL written in the e-
mail text to access the storage location of the image data.
When the size of the mail exceeds the upper limit specified by Maximum Scan
File Size (see p. 2-23) on the Scan to E-mail function
In this case, the image data is saved to the controller HDD, and a URL
indicating the storage location is transmitted by mail.
Note
•
URL notification mails are transmitted according to the mail transmission
settings. You must set the mail transmission settings to use the URL
notification function.
•
If Scanned File Separation (see p. 2-24) is set to Yes and the upper mail
limit specified by Maximum Scan File Size is exceeded, the image data
is first segmented into pages and transmitted. Therefore, the URL
notification mail is not transmitted.
However, if the upper mail limit specified by Maximum Scan File Size is
exceeded even after separating the data up to the number specified by
Maximum Number of E-mails, the image data is saved to the controller
HDD, and a URL notification mail is transmitted. (The image data is
stored to the HDD without separation.)
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6 Entering the Controller Setup Screen
2.6 Entering the Controller Setup Screen
You can enter the controller settings from PageScope Web Connection (see
chapter 1, “ Using PageScope Web Connection”) or the controller operation
panel that is displayed on the copier operation panel. To configure the controller
from the controller operation panel, you must display the setup screen.
Displaying the Setup Screen
1. On the copier operation panel, touch [Utility] — [Controller Details].
2. On the controller operation panel, touch [MENU].
3. Use the up and down keys to show [Run Setup].
4. Touch the key to the right of [Run Setup] to show [Continue to Setup?].
5. Touch the key to the right of [OK] to show the setup screen.
2.7 Setting the Error Notification
Destination
You can carry out the following steps to specify the destination to notify errors
when mails transmitted using the Scan to E-mail, Internet FAX transmission,
e-mail notification function, or URL notification function do not reach the
destination address. However, if the mail is not transmitted, the error is not
notified.
1. Show the setup screen from the controller operation panel.
2. Select [Network Setup] — [Service Setup] — [E-Mail Setup] and enter
the following settings.
[Administrator Email User Name]:
Specify the E-mail user name of the controller
administrator.
[Administrator Email Domain Name]:
Specify the mail server domain name to which the
administrator belongs.
Note
•
Administrator Email User Name@Administrator Email Domain Name is
the error notification destination.
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
2.8 Setting the Sender (From) Address
2.8 Setting the Sender (From) Address
You can carry out the following steps to specify the mail address that appears
in the sender (From) line of the mail transmitted by Scan to E-mail, Internet
FAX transmission, e-mail notification function, and URL notification
function.
1. Show the setup screen from the controller operation panel.
2. Select [Network Setup] — [Service Setup] — [E-Mail Setup] and enter
the following settings.
[Fiery Email User Name]:
Specify the mail user name of the sender.
[Fiery Email Domain Name]:
Specify the mail server domain name to which the
sender belongs.
Note
•
The sender (From) address is Fiery Email User Name@Fiery Email
Domain Name.
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9 Scan to E-Mail Function
2.9 Scan to E-Mail Function
Below is the setup and operation flow of the mail function.
Location of
operation
Controller
A Set the controller
operation panel
PageScope
Web
Connection
(See p. 2-23.)
PageScope
Web
Connection
(See p. 2-35.)
B Register the one-touch key or
temporary registration key
(You can also enter the address directly from the
copier operation panel. See p. 2-12)
Copier
operation panel
(See p. 2-11.)
C Enter scan settings
Copier
operation panel
D Set the document and transfer the
image data to the mail server
Mail client
computer
E Retrieve mail
(See p. 2-25.)
Note
•
Image data is transmitted using port number “25”.
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9 Scan to E-Mail Function
2.9.1 Setting the Controller
To perform mail transmission, enter the settings for accessing the mail server
(SMTP server).
1. Show the setup screen from the controller operation panel.
2. Select [Network Setup] — [Service Setup] — [E-Mail Setup] and enter
the following settings.
[Enable E-mail Services]:
Select “Yes”.
[Outgoing Server]:
Enter the IP address of the mail server (SMTP).
[Time Out (sec)]:
Set the timeout value for accessing the mail server.
Unless there is a specific reason to do so, use the
default value.
(common setting for the SMTP server and POP3
server)
[Maximum Scan File Size]:
Set the maximum transmission mail size.
3. Start PageScope Web Connection.
4. Enter the password and log into the Administrator Mode.
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9 Scan to E-Mail Function
5. Select [Scan Setting] from the [Scan] tab.
Server Name: The “server name” is added to the beginning of the
name of the image file created by the scan function.
(see p. 2-50)
Scanned File Separation:
If set to “Yes”, the image data is segmented into pages
and transmitted when the upper limit specified by
Maximum Scan File Size is exceeded.
For the correlation between Maximum Scan File Size (see p. 2-23),
Scanned file Separation, and URL notification function, see “URL
Notification” on page 2-19.
Maximum Number of E-mails:
Specify the number of separations that is allowed when
the mail is segmented for transmission.
For the correlation between Maximum Scan File Size (see p. 2-23),
Scanned File Separation, URL notification function, and Maximum
Number of E-mails, see “URL Notification” on page 2-19.
2-24
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9 Scan to E-Mail Function
2.9.2 Retrieving Mails
To retrieve mails transferred to the mail server, you must access and retrieve
the mail using the mail client computer.
For details on the operation of your mail client software, see the manual or
help provided with the software program.
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10 Scan to Mailbox Function
2.10 Scan to Mailbox Function
Below is the setup and operation flow of the Scan to Mailbox function.
(For details on the hold period of the image data in the mailbox, see p. 2-52.)
Location of
operation
Controller
Operation
Panel
A Set the controller
(See p. 2-27.)
PageScope
Web
B Create a mail box
Connection
(See p. 2-28.)
PageScope
C Register the one-touch key or
Web
temporary registration key
Connection
(See p. 2-35.)
Copier
operation panel
(See p. 2-11.)
D Enter scan settings
Copier
operation panel
E Set the document and transfer the image
data to the mailbox in the controller HDD.
WebTools
(See p. 2-29)
F Download the image data to the
computer
2-26
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10 Scan to Mailbox Function
Note
•
If you use Fiery Remote Scan, you can download the image data in the
mailbox to the computer or transfer the data via FTP, E-mail, and other
means. For details, see the Controller User Manual.
2.10.1 Setting the Controller
Enter the setting for allowing passwords to be assigned to mailboxes.
1. Show the setup screen from the controller operation panel.
2. Select [Server Setup] and enter the following settings.
[Enable Mailbox Password]:
Select “Yes” to allow passwords to be assigned.
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10 Scan to Mailbox Function
2.10.2 Creating a Mailbox
Create a mailbox, a storage location of the image data.
Note
•
“Admin”, “Operator”, and “Guest” are registered by default.
1. Start PageScope Web Connection.
2. Enter the password and log into the Administrator Mode.
3. Select [Mailbox] from the [File] tab.
4. Click [Create] to open the Create Mailbox screen.
Enter settings for “Mailbox Name”, “Password”, and “Retype Password”
and click [Apply].
Note
•
Up to 20 mailboxes can be created (including “Admin”, “Operator”, and
“Guest”).
2-28
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10 Scan to Mailbox Function
2.10.3 Downloading the Image Data to the
Computer
Download the image data from the mailbox in the controller HDD to your
computer. Download the image data using WebTools.
1. Start PageScope Web Connection.
2. Click [WebTools].
3. Click [WebScan].
4. Enter the mailbox name in [Mailbox] and click [Refresh].
5. Enter the password in the password input dialog box.
A list of stored image data is displayed.
6. Click the file to be downloaded.
7. Select [File Format].
8. Click [Save As] to download the file.
Note
•
If the e-mail notification address is specified, the information indicating
the storage location of the image data is notified by mail.
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
2.11 Scan to FTP Server Function
2.11 Scan to FTP Server Function
Below is the setup and operation flow of the Scan to FTP Server function.
Location of
operation
Controller
operation panel
(See p. 2-31.)
A Enable the FTP transfer function
(Enter proxy settings as necessary. See p. 2-31.)
PageScope
B Register the one-touch key or
Web
temporary registration key
Connection
(See p. 2-35.)
Copier
operation panel
(See p. 2-11.)
C Enter scan settings
Copier
operation panel
D Set the document and transfer the
image data to the FTP server
FTP client
computer or
E Retrieve the image data
PageScope Web
Connection
(See p. 2-32.)
Note
•
Image data is transferred using port number “21”. Passive mode is not
suported.
2-30
Download from Www.Somanuals.com. All Manuals Search And Download.
2.11 Scan to FTP Server Function
2.11.1 Enabling the FTP Transfer Function
1. Show the setup screen from the controller operation panel.
2. Select [Network Setup] — [Service Setup] — [FTP Setup] and enter the
following settings.
[Enable FTP Services]:
Select “Yes”.
2.11.2 Proxy Settings
Enter proxy settings as necessary. (Consult your network administrator to see
if proxy settings are required and the setup details.)
1. Show the setup screen from the controller operation panel.
2. Select [Network Setup] — [Service Setup] — [FTP Setup] and enter the
following settings.
[Enable Proxy Setup]:
Select “Yes” to enable the proxy settings.
[Proxy Server IP Address]:
Enter the IP address of the proxy server.
[Proxy Server Port Number]:
Specify the port number of the proxy server.
[Proxy Server Timeout]:
Set the timeout value.
[Proxy Server User Name]:
Enter the user name of the proxy server.
[Proxy Server User Password]:
Enter the password of the proxy server.
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
2.11 Scan to FTP Server Function
2.11.3 Retrieving the Image Data
Retrieve the image data from the FTP server.
The method for retrieving the image data varies depending on the following
cases.
Access the FTP server from your FTP client computer and download the
image data. You may need to enter a user name and a password to access
the FTP server.
Note
•
If the e-mail notification address is specified, the information indicating
the storage location of the image data is notified by mail. (See p. 2-18.)
2-32
Download from Www.Somanuals.com. All Manuals Search And Download.
2.12 Internet FAX Transmission Function
2.12 Internet FAX Transmission Function
Below is the setup and operation flow of the Internet FAX transmission
function.
Location of
operation
Controller
A Set the controller
operation panel
PageScope
Web
Connection
PageScope
B Register the one-touch key or
Web
temporary registration key
Connection
(You can also enter the address directly from the
copier operation panel. See p. 2-12.)
(See p. 2-35.)
Copier
operation panel
(See p. 2-11.)
C Enter scan settings
Copier
operation panel
D Set the document and transfer the
image data to the mail server
2.12.1 Setting the Controller
Internet FAX Transmission Settings
The image data is transmitted using the same settings as for Scan to E-mail.
For details, see the settings of the “Scan to E-mail” controller (p. 2-23).
Note
•
The “Scanned File Separation” and “Maximum Number of E-mails” settings
do not have to be entered, because they are invalid for Internet FAX.
2-33
Download from Www.Somanuals.com. All Manuals Search And Download.
2.13 Internet FAX Reception Function
2.13 Internet FAX Reception Function
The settings of the Internet FAX reception function are described below.
2.13.1 Setting the Controller
To receive mails, enter settings for accessing the mail server (POP3/IMAP).
1. Show the setup screen from the controller operation panel.
2. Select [Network Setup] — [Service Setup] — [E-Mail Setup] and enter
the following settings.
[Enable E-mail Services]:
Select “Yes”.
[Enable Print Via E-mail]:
Select “Yes”.
[Incoming Server]:
Enter the IP address of the mail server (POP3/IMAP).
[Server Type]: Select the mail server type (POP3/IMAP).
[Account Name]:
Enter the name used to log into the POP3/IMAP server.
[Password]:
Enter the password used to log into the POP3/IMAP
server.
[Timeout (sec)]:
Set the timeout value for accessing the mail server.
(common setting for the SMTP server and POP3 server)
[Polling Interval (sec)]:
Set the interval for checking received mails.
Note
•
If the e-mail contains a title (subject) and text when receiving Internet
FAX, the title and text are also printed.
2-34
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
2.14 Registering the One-Touch Key and
Temporary Registration Key
When using the scan function, it is convenient if the transmission destination
is registered to the copier operation panel in advance. The transmission
destination is registered using PageScope Web Connection.
2.14.1 One-Touch Key Registration
If the one-touch key is registered in advance, you can immediately recall the
transmission destination. Since you do not have to enter the transmission
destination every time, it is convenient if you register destinations to which
you transmit image data frequently.
Setup procedure
1. Start PageScope Web Connection.
2. Select [One Touch Key Registration] from the [Scan] tab.
3. A list of one-touch registration appears. Select an index.
[Index 8] is dedicated to group registration. You can register groups for
the mail transmission function and the Internet FAX transmission
function.
Note
•
There are 8 indexes total. The default names are [Index 1], [Index 2],
and so on. You can register up to 15 keys in each index from [Index 1] to
[Index 6] and [Index 8 (Group)]. Up to 10 keys can be registered in
[Index 7].
2-35
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
4. Click an unregistered box (---).
5. Select the transmission method.
2-36
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
Note
•
For a group registration, the number of characters for the transmission
destination address is up to 1800 (up to 50 addresses).
For registration other than groups, the number of characters for the
transmission destination address is up to 72.
•
6. Click [Apply].
The setup items corresponding to the transmission method appear.
When Scan to E-mail is selected
Destination Name:
Enter the name of the one-touch key.
Up to 12 characters
Address (To): Enter the transmission destination address.
Setting Up to 72 characters, one address
Setting
2-37
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
When specifying [LDAP Settings] (See p. 1-44), use the following
functions.
Search Key:
By inputting [First Name], [Last Name], or [E-mail]
into the empty fields and then clicking the [Lookup
Address] button, only those e-mail addresses registered
on the LDAP server that correspond to the search key
are displayed.
By checking the displayed e-mail addresses and
clicking the [OK] button, the name and e-mail
addresses are automatically input into the [Destination
Name] and [Address (To:)] fields respectively.
Note
•
With an LDAP search, data beginning with the text entered in the [First
Name], [Last Name] and [E-mail] fields is searched for. In addition, if text
is entered into two or three of the [First Name], [Last Name] and [E-mail]
fields, an AND search is performed.
2-38
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
When Scan to FTP Server is selected
Destination Name:
Enter the name of the one-touch key.
Setting
IP Address:
User Name:
Password:
Directory:
Up to 12 characters
Set the IP address of the FTP server.
Enter the name used to log into the FTP server.
Enter the password used to log into the FTP server.
Specify the location (directory) for storing the image
data on the FTP server.
(To specify the default folder, leave this blank.)
Use Default Proxy:
Set whether to use the proxy server.
Notification Address (E-Mail Notification Address):
When using the e-mail notification function, enter the
destination mail address. (See p. 2-18.)
Setting
Up to 72 characters, one address
2-39
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
•
By using the [Search Key] and [Lookup Address] buttons, you can use
the LDAP functions to search and input the [Notification Address]. For
details, see “When Scan to E-mail is selected” on page 2-37.
2-40
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
When Scan to Mailbox is selected
Destination Name:
Setting
Up to 12 characters
Mailbox Name: Select the transmission destination mailbox.
The list shows the mailboxes that have been registered
using [Mailbox] (p. 2-28).
Password:
Enter the password used to access the mailbox.
Up to 8 characters
Setting
Notification Address (E-Mail Notification Address):
Enter the e-mail notification destination mail address.
(See p. 2-18.)
Up to 72 characters, one address
Setting
•
By using the [Search Key] and [Lookup Address] buttons, you can use
the LDAP functions to search and input the [Notification Address]. For
details, see “When Scan to E-mail is selected” on page 2-37.
2-41
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
When Scan to Internet FAX is selected
Destination Name:
Enter the name of the one-touch key.
Setting
Address (To): Enter the transmission destination address.
Setting Up to 72 characters, one address
Up to 12 characters
•
By using the [Search Key] and [Lookup Address] buttons, you can use
the LDAP functions to search and input the [Notification Address].
2-42
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
When Scan to E-mail is selected (Group Registration)
Note
•
•
Group registration is possible only on the [Index 8] mailbox.
Up to 15 groups can be registered.
Enter the name of the one-touch key.
Setting
Up to 12 characters
Address (To): Enter the transmission destination address.
Setting
Up to 1800 characters and up to 50 addresses
•
By using the [Search Key] and [Lookup Address] buttons, you can use
the LDAP functions to search and input the destination e-mail address.
Multiple e-mail addresses can be input simultaneously using group
functions. For details, see “When Scan to E-mail is selected” on page 2-
37.
When Scan to Internet FAX is selected (Group Registration)
Note
•
•
Group registration is possible only on the [Index 8] mailbox.
Up to 15 groups can be registered.
Enter the name of the one-touch key.
Setting
Up to 12 characters
Address (To): Enter the transmission destination address.
Setting
Up to 1800 characters and up to 50 addresses
•
By using the [Search Key] and [Lookup Address] buttons, you can use
the LDAP functions to search and input the destination e-mail address.
Multiple e-mail addresses can be input simultaneously using group
functions. For details, see “When Scan to E-mail is selected” on page 2-
37.
2-43
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
2.14.2 Temporary Registration Key
Registration
Temporary registration is entered using PageScope Web Connection. The
difference from the one-touch registration is that the key is automatically
cleared after the transmission process is executed.
When registering a temporary registration key, you can enter the subject and
text of the mail and enter scan settings.
Setup procedure
1. Start PageScope Web Connection.
2. Select [Temporary Registration] from the [Scan] tab.
3. Click an unregistered box (---).
2-44
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
4. Select the transmission method.
5. Click [Apply]. The setup items corresponding to the transmission
method appear.
When Scan to E-mail is selected
Transmission Destination Settings
Destination Name:
Enter the name of the temporary registration key.
Setting
Address (To): Enter the transmission destination address.
Setting Up to 1800 characters and up to 50 addresses
Subject: Enter the subject.
Up to 64 characters
Up to 12 characters
Setting
Setting
Text:
Enter the mail text to be transmitted.
Up to 256 characters
2-45
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
•
By using the [Search Key] and [Lookup Address] buttons, you can use
Multiple e-mail addresses can be input simultaneously using group
functions. For details, see “When Scan to E-mail is selected” on page 2-
37.
Enter the following settings as necessary.
Scan Mode Settings
The scan mode settings below can also be entered from the copier operation
panel. (For the possible settings of each item, see Setup Items for Scanning
(p. 2-11).)
Original Mode: Specify the document scan mode.
Original Size: Specify the scan size of the document.
Resolution:
File Format (Data Format):
Specify the format of the image file.
Specify the color mode of the image file.
Background Remove:
Enter the background remove settings.
Specify the resolution.
Color Mode:
Orientation:
Specify the image direction with the document set in
the ADF or Platen Grass.
Binding:
Specify the direction of the margin of the document for
duplex printing.
Compression Level:
Specify the compression level of the image file.
Specify the brightness of the document.
Brightness:
2-46
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
When Scan to FTP Server is selected
Destination Name:
Enter the name of the temporary registration key.
Setting
IP Address:
User Name:
Password:
Directory:
Up to 12 characters
Set the IP address of the FTP server.
Enter the name used to log into the FTP server.
Enter the password used to log into the FTP server.
Specify the location (directory) for storing the image
data on the FTP server.
(To specify the default folder, leave this blank.)
Use Default Proxy:
Set whether to use the proxy server.
Notification Address:
When using the e-mail notification function, enter the
destination mail address.
Up to 72 characters, one address
Setting
•
By using the [Search Key] and [Lookup Address] buttons, you can use
the LDAP functions to search and input the [Notification Address]. For
details, see “When Scan to E-mail is selected” on page 2-37.
* Scan Mode Settings (same as for Scan to E-mail)
When Scan to Mailbox is selected
Destination Name:
Enter the name of the temporary registration key.
Setting
Up to 12 characters
Mailbox Name:
Select the transmission destination mailbox.
The list shows the mailboxes that have been registered
using [Mailbox] (p. 2-28).
Notification Address:
Enter the notification destination mail address.
Up to 72 characters, one address
Setting
2-47
Download from Www.Somanuals.com. All Manuals Search And Download.
2.14 Registering the One-Touch Key and Temporary Registration Key
•
By using the [Search Key] and [Lookup Address] buttons, you can use
the LDAP functions to search and input the [Notification Address]. For
details, see “When Scan to E-mail is selected” on page 2-37.
* Scan Mode Settings (same as for Scan to E-mail)
When Scan to Internet FAX is selected
Destination Name:
Enter the name of the temporary registration key.
Setting
Up to 12 characters
Address (To):
Enter the transmission destination address.
Up to 1800 characters and up to 50 addresses
Enter the subject.
Up to 64 characters
Setting
Subject:
Setting
Text:
Enter the mail text to be transmitted.
Up to 256 characters
Setting
•
By using the [Search Key] and [Lookup Address] buttons, you can use
the LDAP functions to search and input the destination e-mail address.
Multiple e-mail addresses can be input simultaneously using group
functions. For details, see “When Scan to E-mail is selected” on page 2-
37.
The Scan Mode setup items are the same as those for mail transmission except
the following items.
Resolution:
File Format:
Color Mode:
Orientation:
200 × 200 dpi (fixed)
TIFF (fixed)
Black & White
No setup item
Compression: No setup item
2-48
Download from Www.Somanuals.com. All Manuals Search And Download.
2.15 Image Data
2.15 Image Data
The image data created by the scan function are described below.
2.15.1 File Format
You can select the file format of the image data from TIFF, PDF, and JPEG.
The following extension is added to the file name depending on the file
format.
TIFF
PDF
Î
Î
Î
.tif
.pdf
.jpg
JPEG
Note
•
Some file formats cannot be specified depending on the selected color
mode.
PDF
{
TIFF
{
JPEG
{
Full color
Grayscale
{
{
{
Monochrome
{
{
—
•
•
When transmitting image data using Internet FAX, only the TIFF format
can be selected.
If you scan multiple pages of the document when JPEG format is
selected, the data is divided into files by pages and attached to the mail.
Example: If 10 pages of the document are scanned, 10 JPEG files are
created and attached to the mail. (Ten JPEG files are attached to a
single mail.)
2-49
Download from Www.Somanuals.com. All Manuals Search And Download.
2.15 Image Data
2.15.2 File Name
The file name of the image data is automatically assigned by the controller.
The file name is assigned according to the following rule.
<Server name><automatic number><the number of pages in the
document*>.extension
* When the mail is segmented for transmission, the last page number of the
attached files is used as a portion of the file names.
You can check the <Server name> by carrying out the following steps.
1. Start PageScope Web Connection.
2. Log into the Administrator Mode.
3. Click the [Scan] tab.
2-50
Download from Www.Somanuals.com. All Manuals Search And Download.
2.15 Image Data
Note
•
The “Server Name” shown in PageScope Web Connection corresponds
to the text specified in “Server Name” on the controller operation panel.
You can check “Server Name” on the controller operation panel by
carrying out the following steps.
1. Show the setup screen from the controller operation panel.
2. Select [Server Setup] — [Server Name] and check the server name.
The automatic number is automatically assigned by the controller and
cannot be specified.
File name example: Server name: test, automatic number: 50, the
number of pages in the document: 35, and PDF file
The file name is test50p35.pdf.
•
•
2-51
Download from Www.Somanuals.com. All Manuals Search And Download.
2.16 Hold Period of the Image Data
2.16 Hold Period of the Image Data
If the number of image data files held in the controller HDD keeps increasing,
there is a possibility that the disk becomes full. You can set the hold period of
the image data in the HDD by carrying out the following settings.
Note
•
When using Scan to Mailbox
The image data is transferred to the HDD and held in the Mailbox
created in the HDD.
•
•
When the size of the mail exceeds the upper limit specified by
[Maximum Scan File Size] on the mail function (see p. 2-23)
When the upper mail limit specified by [Maximum Scan File Size] is
exceeded even after separating the data up to the number specified by
[Maximum Number of E-mails] when the data is separated because the
[Maximum Scan File Size] is exceeded in the mail transmission function
(see p. 2-23, p. 2-24)
1. Show the setup screen from the controller operation panel.
2. Select [Server Setup] and enter the following settings.
[Clear Each Scan Job]:
Select the hold period. The image data is automatically
cleared when the hold period elapses.
After 1 day, Now, Manually, After 1week
Settings
2-52
Download from Www.Somanuals.com. All Manuals Search And Download.
|
