KODAK PROFESSIONAL RP 50 LED Printer
Operator’s Guide
Part No. 2J0686
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Information
Radio Frequency Interference
The United States (47 CFR Part 15 Subpart B, FCC Class A, EMC)
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
IMPORTANT:Changes or modifications to the product that are not authorized by
Eastman Kodak Company could void the FCC Certification and
negate your authority to operate this product.
Canada (ICES-003 Issue 2 Rev1 Canada, Class A, EMC)
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du
Reglement sur le materiel brouilleur du Canada.
European Union (EU, CE Marking, EMC)
This equipment has been type tested and found to comply with the requirements
for electromagnetic compatibility as established by European Communities
Council Directive 89/336/EEC and Low Voltage Directive (Product Safety)
73/23/EEC.
Japan (VCCI, Class 1 EMC)
The following is a translation of the above statement:
“This equipment is in the Class 1 category (information to be used in commercial
and/or industrial areas. Consequently, when used in a residential area or in an
adjacent area thereto, radio interference may be caused to radios and TV
receivers, etc. Read the instructions for correct handling”.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Regulations
IMPORTANT: This equipment incorporates high-voltage components. Adequate safeguards and interlocks
have been designed into this equipment to reduce the risk of injury during normal operation.
As with any electrical equipment of this kind, adequate ventilation must be provided to
minimize exposure to heat, dust, ozone, and other emissions. The following labels will be
found on the product. The exclamation point symbol (A) indicates that the user should refer
to this guide for safety information. The hot symbol (B) indicates a hot surface area on the
printer that should not be touched. The electrical hazard/shock warning symbol (C)
identifies the possibility of electrical shock inside an area that should only be accessed by
Kodak CES personnel.
A
B
C
CAUTION:
Before connecting or disconnecting the SCSI cable or terminator, turn off the power
for the printer and the host computer. Also, if you replace the SCSI cable, remove the
Ferrite bead from the existing SCSI cable and install it on the new SCSI cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
Environmental Regulations
IMPORTANT: Always adhere to your local ordinances and regulations for disposal of paper, chemicals,
filters, cleaning supplies, etc.
Warranty Information
The following warranty information pertains to equipment that is installed in the United States
only. For equipment installed in countries other than the United States, the terms and conditions
of the new equipment warranty will be provided by the Kodak company in the country in which
the sale is finalized, or by a Kodak-appointed distributor in those countries where Kodak does
not have direct sales representation.
Warranty Period
Kodak warrants new equipment to function properly for 90 days from the date of initial
installation. This warranty covers the purchaser of this equipment as well as anyone else who
owns it during the warranty period.
Warranty Repair Coverage
If this equipment does not function properly during the warranty period, a Kodak Customer
Equipment Services Field Engineer will repair the equipment without charge during Kodak’s
normal working hours (usually 8:00 a.m. to 5:00 p.m., Monday through Friday). Such repair
service will include any adjustments and/or replacement of parts required to maintain your
equipment in good working order. Supply items are billed as required.
Off-hours services are available at overtime rates.
How to Obtain Service
For technical support, service, repair and fuse replacement information, contact Eastman Kodak
Company’s Technical Assistance Center at 1-800-822-1414.
Limitations
Warranty Service is limited to areas within Kodak’s established marketing centers in the
contiguous United States, the island of Oahu in Hawaii, and certain areas of Alaska.
This warranty does not cover circumstances beyond Kodak’s control; service or parts for any
attachments, accessories, or alterations not marketed by Kodak, nor to correct problems
resulting from their use.
Damaged caused by failure to meet electrical specifications in this manual will not be covered
under the warranty or service agreement claim.
Damage to the imaging shoe as a result of customer misuse or abuse will not be covered under
the warranty or service agreement claim. Do not use sharp objects to clear paper in this area.
Kodak makes no other warranties, express, implied or of
merchantability, for this equipment.
Repair or replacement without charge is Kodak’s only obligation under this warranty. Kodak will
not be responsible for any consequential or incidental damages resulting from the sale, use or
improper functioning of this equipment, even if loss or damage is caused by the negligence or
other fault of Kodak.
Such damages, for which Kodak will not be responsible, include, but are not limited to, loss of
revenue of profit, downtime costs, loss of use of the equipment, cost of any substitute
equipment, facilities or services or claims of your customers for such damages.
Download from Www.Somanuals.com. All Manuals Search And Download.
This limitation of liability will not apply to claims for injury to persons or damage to property
caused by the sole negligence or fault of Kodak or by persons under its direction or control.
Kodak Service Agreements
For information on Kodak Service Agreements, call Kodak Service Marketing Operations
at 1-800-645-6325.
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide..................................................................................................................................... xiii
Using This Guide................................................................................................................... xiv
About Other Publications ...................................................................................................... xiv
Software Included with the Printer ........................................................................................ xiv
Getting Help from Kodak........................................................................................................ xv
1 Introduction........................................................................................................................................... 1-1
Product Description............................................................................................................... 1-1
SCSI Interface ................................................................................................................ 1-1
KODAK PROFESSIONAL RP 50 LED Printer................................................................ 1-1
KODAK PROFESSIONAL Processor............................................................................. 1-2
Installation and Service .................................................................................................. 1-2
Equipment Overview............................................................................................................. 1-2
2 Using the System ................................................................................................................................. 2-1
Starting up the Processor...................................................................................................... 2-1
Starting up the Printer ........................................................................................................... 2-2
Calibrating the Printer ........................................................................................................... 2-3
Obtaining Densities ........................................................................................................ 2-6
Obtaining Densities from a File ................................................................................2-6
Using the Densitometer to Read Densities ..............................................................2-6
Completing the Calibration ............................................................................................. 2-7
Making Prints ........................................................................................................................ 2-9
Shutting Down the Processor.............................................................................................. 2-10
Shutting Down the Printer ................................................................................................... 2-11
3 System Operating Procedures ............................................................................................................. 3-1
Operating the Printer............................................................................................................. 3-2
Operator Control Panel................................................................................................... 3-2
OCP Key/Light Descriptions .....................................................................................3-3
Menu ........................................................................................................................3-4
Printer Offline Feature ..............................................................................................3-4
Cancelling Jobs ........................................................................................................3-4
Printing Deferred or Buffered Jobs................................................................................. 3-4
Status Messages............................................................................................................ 3-5
Loading Paper Into the Supply Cassette ........................................................................ 3-6
Removing the Supply Cassette ................................................................................3-6
Loading Paper into the Supply Cassette ..................................................................3-7
Installing the Supply Cassette ................................................................................3-10
Reaching the End of the Roll of Paper ......................................................................... 3-13
Removing the Chad...................................................................................................... 3-14
Handling and Storing the Paper ................................................................................... 3-14
Storing Paper Using the Soft Shutdown Feature ...................................................3-14
October 2002
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing the Printer Features........................................................................................... 3-15
Shutdown and Restart .................................................................................................. 3-15
Shutdown ...............................................................................................................3-15
Restart ....................................................................................................................3-15
Unload Supply .............................................................................................................. 3-15
Selecting SCSI Ports.................................................................................................... 3-15
Selecting the Target Pad Read Options .................................................................3-16
Managing a Modem...................................................................................................... 3-16
Resetting the Modem Port .....................................................................................3-16
Checking for a Modem ...........................................................................................3-16
Setting the Printer Time and Date ................................................................................ 3-17
Setting the Current Time ........................................................................................3-17
Setting the Current Date ........................................................................................3-17
Setting the Current Day ..........................................................................................3-17
Setting the Paper Length.............................................................................................. 3-17
Selecting the Slug Width for the Paper......................................................................... 3-18
Setting the Page Starts Value ...................................................................................... 3-19
Producing Borderless Prints ...................................................................................3-20
Accessing the Software Version Number ..................................................................... 3-22
Setting the Copyright Detection Feature ...................................................................... 3-22
Resetting the Defaults .................................................................................................. 3-23
Resetting the Parameters ......................................................................................3-23
Resetting the Printing LUTs ...................................................................................3-23
Resetting the Copyright Detection LUTs ................................................................3-23
Changing the Units of Measurement for Paper Sizes................................................... 3-24
About Printing...................................................................................................................... 3-24
Image Size.................................................................................................................... 3-24
Buffered and Unbuffered Jobs (or Immediate and Deferred) ....................................... 3-24
Printing Deferred or Buffered Jobs .........................................................................3-25
Host Software Functions Supported by the Printer....................................................... 3-25
Bar Coding .............................................................................................................3-25
Pixel Doubling ........................................................................................................3-25
Operating the Processor ..................................................................................................... 3-26
Operator Control Panel................................................................................................. 3-26
View Mode .............................................................................................................3-26
Set Mode ................................................................................................................3-26
Calibrate Mode .......................................................................................................3-26
Min Max Mode ........................................................................................................3-26
OCP Key/Light Descriptions ...................................................................................3-27
Status Messages ....................................................................................................3-28
OCP On/Off Light ...................................................................................................3-29
Operational Modes ....................................................................................................... 3-30
Adjusting the Key Switch Lock ...............................................................................3-31
Processing a Control Strip............................................................................................ 3-32
Viewing/Setting the Processor Time and Date ............................................................. 3-33
Viewing the Current Time Setting ..........................................................................3-33
Setting the Current Time ........................................................................................3-33
Setting the Current Date ........................................................................................3-33
Viewing/Setting the Seven-Day Timer.......................................................................... 3-34
Viewing the On/Off Times ......................................................................................3-34
Setting the On/Off Times ........................................................................................3-34
Viewing the Software Identification............................................................................... 3-34
viii
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing/Setting the Temperatures ............................................................................... 3-35
Viewing the Temperature Settings .........................................................................3-35
Setting the Temperature ........................................................................................3-35
Calibrating the Temperatures....................................................................................... 3-35
Resetting the Min Max Temperatures........................................................................... 3-35
Viewing/Setting Replenishment Settings...................................................................... 3-36
Viewing the Replenishment Rate ...........................................................................3-36
Setting the Chemical Replenishment Rate ............................................................3-36
Setting the Wash Replenishment Rate ..................................................................3-36
Calibrating the Replenishment Flow Rate .................................................................... 3-36
Measuring the Flow Rate .......................................................................................3-36
Entering the Flow Rate ...........................................................................................3-37
Managing the Development Time................................................................................. 3-37
Viewing the Development Time .............................................................................3-37
Setting the Development Time ...............................................................................3-37
Calibrating the Development Time .........................................................................3-37
Displaying the Min Max Development Time ...........................................................3-38
Managing the Material Sensors.................................................................................... 3-38
Viewing the Material ...............................................................................................3-38
Viewing the Processor Setup .................................................................................3-38
Selecting the Processor Setup ...............................................................................3-38
Controlling the Processor Drive.................................................................................... 3-39
Turning the Drive On ..............................................................................................3-39
Returning the Drive to Normal Operation ...............................................................3-39
Computer Reset ........................................................................................................... 3-39
Resetting the Processor .........................................................................................3-39
Loading the Defaults and Changing the Configuration ..........................................3-39
Changing the Wash/Stabilizer Setup............................................................................ 3-40
Changing the Metric/Fahrenheit Mode ......................................................................... 3-40
Setting the Development Time Tolerance .................................................................... 3-41
Setting the Chemical Temperature Tolerance.............................................................. 3-41
Clearing Error Conditions ............................................................................................. 3-41
4 Maintaining the Equipment................................................................................................................... 4-1
Removing the Chad .................................................................................................4-2
Calibrating the Printer ..............................................................................................4-2
Cleaning the Crossover Assemblies ........................................................................4-5
October 2002
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the Circulation ..........................................................................................4-7
Replacing Chemical and Wash Filters ...................................................................4-10
5 Diagnostics and Troubleshooting ......................................................................................................... 5-1
Printer Error Messages ......................................................................................................... 5-2
Manual or Automatic Reinitialization............................................................................... 5-2
Printer Paper Path .......................................................................................................... 5-3
Printer Error Messages................................................................................................... 5-4
Miscellaneous Printer Error Messages......................................................................... 5-10
Clearing Printer Paper Jams ........................................................................................ 5-11
Troubleshooting Observable Errors.............................................................................. 5-12
Additional Troubleshooting Tips for the Printer............................................................. 5-15
Processor Error Messages.................................................................................................. 5-16
Clearing Error Messages.............................................................................................. 5-17
Clearing a Reset Message ........................................................................................... 5-17
Clearing Processor Paper Jams................................................................................... 5-18
Clearing Drive Errors.................................................................................................... 5-18
Additional Troubleshooting Tips for the Processor....................................................... 5-19
Calibration Troubleshooting ................................................................................................ 5-19
Calibration Graph ......................................................................................................... 5-19
Calibration Error Codes ................................................................................................ 5-20
Non-Numeric Error Messages...................................................................................... 5-26
Getting Additional Help ....................................................................................................... 5-27
Appendix A: Ordering Supplies .............................................................................................................. A-1
Supplies ............................................................................................................................... A-1
Standard (U.S.) Paper.......................................................................................................... A-2
Metric Paper......................................................................................................................... A-2
Processor Chemicals ........................................................................................................... A-3
x
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: Specifications..................................................................................................................... B-1
Printer/Processor Specifications .......................................................................................... B-1
Dimensions and Weight................................................................................................. B-1
Acoustic Specifications.................................................................................................. B-1
Site Requirements................................................................................................................ B-2
Operator and Service Access........................................................................................ B-2
Floor Requirements ....................................................................................................... B-2
Electrical........................................................................................................................ B-4
Power Cords.................................................................................................................. B-5
Power Outlets ................................................................................................................ B-5
Line Frequency.............................................................................................................. B-6
Power Receptacles (U.S. and Canada)......................................................................... B-6
Printer Power Receptacles (Europe) ............................................................................. B-7
Processor Power Receptacles (Europe)........................................................................ B-8
Line Voltage................................................................................................................... B-9
Operating Environment................................................................................................ B-10
Processor Humidity Specifications .............................................................................. B-11
Wash Chemicals.......................................................................................................... B-11
Telephone line ............................................................................................................. B-11
Densitometer ............................................................................................................... B-11
SCSI Cable.................................................................................................................. B-12
Appendix C: Additional Calibration Information...................................................................................... C-1
Installing the Calibration Software........................................................................................ C-1
System Requirements ................................................................................................... C-1
Installation Procedure.................................................................................................... C-2
Kodak Device Calibration Software...................................................................................... C-4
Application Window Definitions ..................................................................................... C-4
Starting the Kodak Device Calibration Software............................................................ C-6
Adding a Device ............................................................................................................ C-6
Editing the Log Settings................................................................................................. C-8
Updating a Device ......................................................................................................... C-9
Deleting a Device ........................................................................................................ C-10
Advanced Features of the Calibration Software................................................................. C-11
Viewing Graphs ........................................................................................................... C-11
Sending LUTs.............................................................................................................. C-15
Sending Targets .......................................................................................................... C-17
Editing the Calibration Configuration ........................................................................... C-19
Editing Information on the Procedure Tab ............................................................ C-22
Editing Information on the Density Source Tab ..................................................... C-24
Editing Information on the Aim Tab ....................................................................... C-25
Editing Information on the History Tab .................................................................. C-26
Editing Information on the Paper Tab .................................................................... C-27
Editing Information on the DP2 (Windows NT) or KPIS (Macintosh) Tab ............. C-27
Completing the Edit Configuration ........................................................................ C-31
Creating a Density File for Use with Calibration .......................................................... C-32
File Formats................................................................................................................. C-32
Installing the Densitometer................................................................................................. C-33
October 2002
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Using the Image Print Server Software.............................................................................. D-1
Installing the IPS Software................................................................................................... D-1
Software Requirements ................................................................................................. D-1
Installing the Software ................................................................................................... D-2
Using the Image Print Server............................................................................................... D-2
Inserting Images into the Print Queue ........................................................................... D-2
Source Directory Insertion .......................................................................................D-2
Failed Jobs .................................................................................................................... D-3
Attended Operation ....................................................................................................... D-3
Enqueue Example ......................................................................................................... D-4
Dialog Boxes and Print Options ........................................................................................... D-6
Option Descriptions ....................................................................................................... D-7
Enqueue Dialog Box...................................................................................................... D-8
Option Descriptions ................................................................................................. D-8
Source Directory Preferences Dialog Box ..................................................................... D-9
Option Descriptions ................................................................................................. D-9
Initialize Default Parameters Dialog Box ..................................................................... D-10
Description ............................................................................................................ D-10
File Format Details ...................................................................................................... D-10
Supported Tags........................................................................................................... D-10
LZW Compression....................................................................................................... D-10
Appendix E: Using the PHOTOSHOP Export Module............................................................................ E-1
Installing the Export Module................................................................................................. E-1
Hardware Requirements................................................................................................ E-1
Software Requirements ................................................................................................. E-1
Installing the Software ................................................................................................... E-2
Printing Images .................................................................................................................... E-3
Dialog Boxes and Print Options ........................................................................................... E-6
KODAK LED Main Dialog Box....................................................................................... E-6
Punch Attributes ............................................................................................................ E-7
Page Layout Attributes ................................................................................................. E-8
Select an LED Printer Dialog Box.................................................................................. E-8
Option Descriptions ....................................................................................................... E-9
Printer Status Dialog Box .............................................................................................. E-9
Option Descriptions ..................................................................................................... E-10
Troubleshooting ................................................................................................................. E-10
Error messages ........................................................................................................... E-10
General error messages ....................................................................................... E-10
Index................................................................................................................................................ Index-1
xii
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
This is an Operator’s Guide for the KODAK PROFESSIONAL RP 50 LED Printer
and Processor.
It provides step-by-step instructions for the operations you perform while using the
Printer and Processor as a system. It also includes procedures and information for
operating, maintaining, troubleshooting, and calibrating the system.
Also included in this guide are instructions for installing and using the various
software packages needed.
This guide is intended for personnel who operate this system. It assumes that you
can perform basic computer operations. MACINTOSH and
WINDOWS NT Platforms are supported in this guide.
This document also applies to the KODAK PROFESSIONAL LED II Printer 20P
and Processor.
Using This Guide
This guide is organized as follows:
Chapter 1
Introduction—describes and illustrates the KODAK
PROFESSIONAL RP 50 LED Printer and Processor. This
chapter includes general and introductory information for all
of the equipment.
Chapter 2
Chapter 3
Chapter 4
Chapter 5
Using the System—explains how to use the printer and
processor. It includes the step-by-step instructions for daily
operation, from startup to shutdown.
System Operating Procedures—provides an overview of
the OCPs and all procedures for operating both the Printer
and the Processor.
Maintaining the Equipment—includes the information that
you need to properly maintain the printer and processor. All
maintenance procedures are categorized by frequency.
Diagnostics and Troubleshooting—provides an error
code listing, solutions to common operational problems for
the printer, processor and calibration. It also provides
information for obtaining additional help.
Appendix A
Ordering Equipment, Accessories, and Supplies—
provides ordering information for many associated items. It
includes information such as size, quantities, and catalog
numbers.
October 2002
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
Appendix B
Appendix C
Specifications—provides specifications, site
requirements, andenvironmentalinformation forthe system.
Calibrating the Printer—describes the calibration
functions for the KODAK Calibration Software and the
Printer Calibration Software.
Appendices D-F Software—explains how to install and use software that is
included with the system.
About Other Publications
The following publication is included with the printer:
Quick Reference Guide for the KODAK PROFESSIONAL RP 50 LED Printer
and Processor–provides quick and easily accessible information for operating
and maintaining the printer as well as answers to common printer problems and
hints for operating the processor. Keep the Quick Reference Guide close to your
printer.
Software Included with the Printer
The compact disc (CD) included with the KODAK PROFESSIONAL RP 50 LED
Printer contains the KODAK Calibration Software and the Printer Calibration
Software for WINDOWS NT and MACINTOSH Host Computers. It also includes
additional applications the printer can interface with.
This software is usually installed by a Kodak representative. However, installation
instructions are included in this Operator’s Guide.
A PDF file of this Operator’s Guide is also included on the CD.
You can find the latest software and documentation for the KODAK
PROFESSIONAL LED Printers on the Kodak Web site: www.kodak.com.
xiv
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
Getting Help from Kodak
Your Kodak sales representative is the best source for information about setting
up and operating your printer and for obtaining accessories and supplies. Please
contact your Kodak sales representative if you have any questions.
Kodak Sales Representative:___________________________
Representative’s Telephone Number: ____________________
K-Number: _________________________________________
In addition, for technical support in the U.S., call 1-800-822-1414 between
8:00 a.m. and 8:00 p.m. Eastern Standard Time on regular business days.
You can also use the technical support number for information on:
•
•
•
•
•
operating the printer
how or where to obtain supplies
how to obtain service
the warranty
other Kodak products
If you are calling for technical support, please know your printer’s K-Number. The
K-Number label is attached to the front of the printer, next to the operator
control panel.
Product Literature
The faxback number for product literature is 1-800-508-1531. You may call this
number 7 days a week, 24 hours a day.
October 2002
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Introduction
This chapter includes the following information about the KODAK
PROFESSIONAL RP 50 LED Printer.
Product Description ...........................................................................................1-1
SCSI Interface .............................................................................................1-1
KODAK PROFESSIONAL RP 50 LED.........................................................1-1
Processor ....................................................................................................1-2
Installation and Service ...............................................................................1-2
Equipment Overview ..........................................................................................1-2
October 2002
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Product Description
The KODAK PROFESSIONAL RP 50 LED Printer printing system offers a
combination of printing and processing options that produces photographic quality
output of digital images. The images are printed at a resolution of 250 dpi and at
sizes varying from 8 x 10 in. to 20 x 33 in.
Images printed with this system are comparable to images produced on an optical
printer. By using KODAK PROFESSIONAL Digital Paper with proper color
management, the 20P printer provides the “look” of VPS film on KODAK PORTRA
or SUPRA Paper, or GOLD Film on KODAK EKTACOLOR Edge Paper.
The system consists of a MACINTOSH or PC host computer to manage and
manipulate the digital source image, a SCSI interface to transfer the digital image
to the printing system, the KODAK PROFESSIONAL RP 50 LED Printer to
expose the digital image, and the Processor, to develop the image and deliver the
print.
You can use a variety of software applications (such as KODAK Image Print
Server Software) to manage and manipulate the digital images.
SCSI Interface
A SCSI cable connects the host computer to the KODAK PROFESSIONAL RP 50
LED Printer. This interface transfers the digital image data from the host computer
to the printer.
KODAK PROFESSIONAL RP 50 LED Printer
The KODAK PROFESSIONAL RP 50 LED Printer exposes digital images on
photographic quality paper using a sophisticated technology involving Light
Emitting Diodes (LEDs). The printer uses KODAK PROFESSIONAL Paper in
24.4 cm, 27.9 cm, 30.5 cm and 50.8 cm and A4 widths to create prints the size of
20.3 cm x 25.4 cm up to 50.8 cm x 83.8 cm. The printer then delivers the exposed
paper to the Processor, where RA-4 processing techniques develop the image
and deliver the print.
1-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Processor
The Processor is designed as a companion processor for the KODAK
PROFESSIONAL RP 50 LED Printer. The processor uses RA-4 processing
techniques to develop the image and deliver the print. These techniques move the
exposed paper through four tanks consisting of Developer, Bleach/Fix, Stabilizer 1
and Stabilizer 2. The paper, which contains a visible color image, is dried and
output as a completed print.
Installation and Service
The KODAK PROFESSIONAL RP 50 LED Printer and Processor must be
installed and serviced by a qualified Kodak service representative.
Equipment Overview
processor
paper supply
door
printer
Front View
host computer and SCSI cable
(not included)
sheet
transport
door (front)
operator
control panel
for the printer
densitometer (not included)
front door
October 2002
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Rear View
operator control
panel for the
processor
connector
ports
back door
sheet transport door (rear)
1-4
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Using the System
This chapter explains how to use the KODAK PROFESSIONAL RP 50 LED
Printer and Processor for daily operations. It takes you from startup to shutdown.
Topics include:
Starting up the Processor ..................................................................................2-1
Starting up the Printer ........................................................................................2-2
Calibrating the Printer ........................................................................................2-3
Obtaining Densities .....................................................................................2-6
Completing the Calibration ..........................................................................2-7
Making Prints .....................................................................................................2-9
Shutting Down the Processor ..........................................................................2-10
Shutting Down the Printer ................................................................................2-11
Starting up the Processor
1. Check that the circuit breaker switch for the processor is turned on.
circuit breaker
switch
2. Press On/Off on the processor’s Operator Control Panel to turn the processor
on.
The light above the On/Off key indicates the processor state. A blinking light
indicates that the processor is on but the chemicals are not yet at the correct
working temperature. A continuous light indicates that the processor is ready.
October 2002
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
WARNING: When handling or mixing chemical solutions, wear protective
eyewear, clothing,andgloves. Forsafehandingpracticeswith
all chemicals, refer to the MSDS information.
3. Check that the chemistry in each processor tank is at the top of the overflow
pipe. If necessary, add warm water to reach the correct level.
CAUTION: Usewatertotopoffthe chemical tanks. Donotusereplenisher
chemistry.
overflow
pipe
4. After the temperature is up to the correct level, operate the main drive for
30 minutes. See “Controlling the Processor Drive” on page 3-39.
5. Process a control strip. See “Processing a Control Strip” on page 3-32.
Starting up the Printer
1. Verify that the processor is on, up to the correct temperature, and in control.
2. If needed, turn the circuit breaker on the back of the printer on.
When the Power and Standby LEDs on the OCP are illuminated, press the
Start key on the OCP to begin printer initialization.
If paper is loaded, when initialization is complete (in 3 to 4 minutes) the
message “Status: ON LINE - Ready” appears on the OCP. Startup is
complete and the printer is ready to print. Turn the computer on; then go to
the next page and calibrate the printer.
If paper is not loaded, the message “Out of paper, open supply door
to load” appears on the OCP. Do the procedures below.
• “Loading Paper Into the Supply Cassette” on page 3-6.
• “Installing the Supply Cassette” on page 3-10.
When “On-line and Ready” is displayed, turn the host computer on. Go to
the next page and calibrate the printer.
2-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
Calibrating the Printer
You need to calibrate the printer when you start the system up each day. You also
need to calibrate the printer when
• you change paper
• print quality is questionable
• the temperature at the site changes more than 5° F (2.8° C)
• if running more than one shift, at the beginning of each shift
If you are calibrating at any time other than during the daily startup procedure:
Before you begin, make sure the printer is not receiving printing commands from
the host.
NOTE: Most windows displayed in this section are from the Windows NT version
of the software. The windows for the Macintosh version of the software are
similar.
For information about editing the calibration settings (for example, you may want
to display a calibration graph only if calibration is out of tolerance), see “Editing
the Calibration Configuration” on page Appendix C:-19.
To calibrate the printer:
1. Check that:
• the densitometer is connected and calibrated
• the printer status is “Online and Ready”
• the processor is in control
• the calibration application is running
2. Select the icon for the LED Printer on the KODAK Device Calibration screen
and click the Calibrate icon. The calibration software needs complete control
of the printer to successfully calibrate the printer.
IMPORTANT:If no icon appears on the KODAK Device Calibration Screen, you
will need to add a calibration device. See “Adding a Device” on
page C-6.
Calibrate
icon
October 2002
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
The LED Calibration screen appears.
3. Click the Go icon to start the calibration cycle.
Go icon
This icon highlights after
you select Go
Downloading LUTs and Sending Test Print highlights.
If the configuration file specifies to Ask if processor is in control, the
Process In Control dialog box appears.
The processor is critical to printer calibration. You can calibrate the printer
only if the processor is in control. Densitometers require calibration at regular
intervals. Refer to your densitometer’s manual for instructions on how to
calibrate your densitometer.
4. Click Yes.
2-4
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
The Send LUT to Printer screen appears.
NOTE: The highlighted LUT in the dialog box above is the most recent
calibration LUT.
5. Click either Load Selected LUT or Load Custom LUT (or Cancel to cancel
the calibration process).
If you click Load Selected LUT, the system automatically downloads the
highlighted LUT to the printer to create a test print.
When the test print has been sent, the Scanning Processed Print with
Densitometer status icon on the LED Printer Calibration screen highlights.
Select or type the name of the LUT file you want and click Open.
October 2002
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
The system automatically downloads the LUT file to the printer to create a test
print. When the test print has been sent to the printer, the Scanning
Processed Print with Densitometer status icon on the KODAK LED Printer
Calibration screen highlights.
Obtaining Densities
Obtaining Densities from a File
If the configuration settings include obtaining the density data from a file, the
Waiting for Density File dialog box appears. Otherwise, go to “Using the
NOTE: To create a density file, see“Creatinga DensityFileforUsewith Calibration”
on page Appendix C:-32.
1. Click OK to continue with the calibration process.
Using the Densitometer to Read Densities
Do the following to scan the neutral (gray) patches on the processed test print into
the densitometer (refer to your densitometer manual for detailed instructions on
using the densitometer):
1. Slide the lever on the densitometer to position 15. Align the edge of the test
print with the lever on the densitometer. Gently feed the test print through the
densitometer to scan the patches labeled “even”.
2. Slide the lever on the densitometer to position 20. Align the edge of the test
print with the lever on the densitometer. Gently feed the test print through the
densitometer to scan the patches labeled “odd”.
2-6
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
3. Slide the lever on the densitometer to position 30. Align the edge of the test
print with the lever on the densitometer. Gently feed the test print through the
densitometer to scan the patches labeled “both”.
Lever
Test print
If the test print is read successfully, several messages will appear in the status
bar; the final message indicates that the densitometer values have been
successfully received. Go to “Completing the Calibration.”
If the test print is not read successfully, refer to “Calibration Troubleshooting”
on page 5-19.
Completing the Calibration
1. If calibration is in tolerance, the LUT Attributes dialog box appears.
a. Enter a name or comment in the dialog box. The comment you enter will
appear on the Send LUT to Printer screen to identify the LUT file with a
name that is meaningful to you (up to 75 characters).
b. Click OK.
The new printing LUT is calculated and downloaded. “Calibration
Complete” appears in the status bar. The calibration is complete.
2. If calibration is out of tolerance, it may be necessary to run four or more
iterations of the calibration cycle to achieve a successful calibration.
October 2002
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
If the print densities are out of tolerance, a graph appears, allowing you to
select the type of data and planes that you want to see displayed.
a. Click OK.
The following list of options appears.
Re-read the densitometer values is the most useful when the graphs
show an unusual plot. Rereading the test print lets you validate the graph,
then returns you to the Out of Tolerance dialog box.
Iterate again using a newly calculated calibration LUT allows you to
keep printing test prints with the newly created LUT without having to save
the LUT table.
Calculate and download a printing LUT and stop: When you select this
option, the file is saved and given the same creation date and time as the
name.
Cancel and return the printer to its original state saves nothing. Any
corrupted data created after you saved the last time is thrown away.
2-8
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
b. Select one of the four options to try to complete the calibration
successfully.
• If the Out of Tolerance dialog box appears again, repeat this step until
• If you cannot get a successful calibration, request help from a system
administrator or service person.
Making Prints
You can make prints with a wide variety of applications that run on WINDOWS NT
Computers and MACINTOSH Computers. One application that is widely used for
printing is the KODAK PROFESSIONAL Imaging System.
Two applications that you may wish to print from are included with the system.
You can use the KODAK PROFESSIONAL Image Print Server for WINDOWS NT
to print TIFF images. You can use the Export Module for ADOBE PHOTOSHOP
that runs on MACINTOSH Computers to print images from the PHOTOSHOP
application.
For more information about these applications, see the appropriate Appendix in
this guide.
October 2002
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
Shutting Down the Processor
To shut down the processor, press the On/Off key on the processor OCP.
Shutting down the processor for service
If you are shutting the processor down for service, turn off the processor circuit
breaker after the green light on the OCP is no longer illuminated. The exhaust fan
in the processor will continue to operate.
IMPORTANT: If the processor will not be used for longer than four days, drain,
flush, and clean the processor tanks.
1. Remove the top cover and the light tight cover from the processor.
top cover
light tight cover
2-10
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
CAUTION: Install a splash guard over the entrance area of the processor
to prevent water and chemicals from entering the printer.
2. Pour warm water over the top of the rollers.
splash guard
top rollers
3. Reinstall the light tight cover and the top cover on the processor.
NOTE: After the processor is turned off, the recirculation pumps continue to
operate for 30 seconds.
Shutting Down the Printer
1. Check that all jobs in the print queue are printed.
2. Perform a soft shutdown:
a. Press the On/Off Line key on the OCP to take the printer offline.
b. Press the Menu button on the OCP to access the menu.
c. Select “Shutdown” in the message display.
d. Press the Start key.
e. Select “Shutdown now” in the message display.
f. Press the Select key to begin the shutdown.
NOTE: If any jobs are not complete, you will be asked if you want to delete the
remaining jobs before you can select Shutdown.
October 2002
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the System
CAUTION: Turn off the circuit breaker only after doing the soft shutdown.
Otherwise, you could lose printer status information and
cause dark lines to appear in the middle of the prints if paper
is loaded.
3. Turn off the circuit breaker on the back of the printer.
circuit breaker
2-12
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
3 System Operating Procedures
This section provides the information you need to operate the KODAK
PROFESSIONAL RP 50 LED Printer. Topics include:
Operating the Printer .........................................................................................3-2
Operator Control Panel ...............................................................................3-2
Printing Deferred or Buffered Jobs...............................................................3-4
Status Messages .........................................................................................3-5
Loading Paper Into the Supply Cassette .....................................................3-7
Reaching the End of the Roll of Paper ......................................................3-13
Removing the Chad ..................................................................................3-14
Handling and Storing the Paper ................................................................3-14
Accessing the Printer Features ........................................................................3-15
Shutdown and Restart ...............................................................................3-15
Unload Supply ...........................................................................................3-15
Selecting SCSI Ports .................................................................................3-15
Managing a Modem ..................................................................................3-16
Setting the Printer Time and Date .............................................................3-17
Setting the Paper Length ..........................................................................3-17
Selecting the Slug Width for the Paper .....................................................3-18
Setting the Page Starts Value ...................................................................3-19
Accessing the Software Version Number ..................................................3-22
Setting the Copyright Detection Feature ...................................................3-22
Resetting the Defaults ...............................................................................3-23
Changing the Units of Measurement for Paper Sizes ...............................3-24
About Printing ..................................................................................................3-24
Image Size ................................................................................................3-24
Buffered and Unbuffered Jobs (or Immediate and Deferred) ....................3-24
Host Software Functions Supported by the Printer ...................................3-25
Operating the Processor ..................................................................................3-26
Operator Control Panel .............................................................................3-26
Operational Modes ....................................................................................3-30
Processing a Control Strip ........................................................................3-32
Viewing/Setting the Processor Time and Date ..........................................3-33
Viewing/Setting the Seven-Day Timer ......................................................3-34
Viewing the Software Identification ...........................................................3-34
Viewing/Setting the Temperatures ............................................................3-35
Calibrating the Temperatures ....................................................................3-35
Resetting the Min Max Temperatures .......................................................3-35
Viewing/Setting Replenishment Settings ..................................................3-36
Calibrating the Replenishment Flow Rate .................................................3-36
Managing the Development Time .............................................................3-37
Managing the Material Sensors ................................................................3-38
Controlling the Processor Drive ................................................................3-39
Computer Reset ........................................................................................3-39
Changing the Wash/Stabilizer Setup ........................................................3-40
Changing the Metric/Fahrenheit Mode ......................................................3-40
Setting the Development Time Tolerance .................................................3-41
Setting the Chemical Temperature Tolerance ..........................................3-41
Clearing Error Conditions ..........................................................................3-41
October 2002
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Operating the Printer
Operator Control Panel
The operator control panel (OCP) for the printer allows you to view and control:
•
•
•
•
•
•
•
current status of the printer
current time of day
paper specifications
error and power status
cancel, on/off line and menu functions
parameters of the printer
error messages
LED indicator
lights
time of day
current status
LCD display
Power
Error Standby
Status: Initializing
2:43
Pages Waiting:
PaperWidth:
PaperSupply:
Next Print (sec):
Start
Cancel
On/Off Line
Menu
Select
Select
key
printing information
Up, Down and Right
select keys
function keys
The display on the OCP is a 4 line by 40 character liquid crystal display (LCD). An
audible beeper is installed to the right of the LCD display. Each of the function
keys also operates as the arrow key (selector) directly below it when Menu has
been pressed. LED indicator lights illuminate to indicate power, error, and standby
statuses.
The operator control panel (OCP) displays the current status of the printer,
including the following information:
• Pages Waiting – the number of printing jobs that are waiting in the print queue
• Next Print (sec) – the approximate amount of time (in seconds) until the next
sheet of processed paper will exit the processor
• Paper Width – the width of the current roll of paper that is installed in the
printer
• Paper Supply – the approximate amount of paper left in the paper cassette.
This information is input by you and is for your convenience only
3-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
OCP Key/Light Descriptions
Key /LED
Indicator Light
Key/Light
Description/Function
Start Key
The Start key turns on the power for the printer when the printer has
been shut down through the OCP. When using the OCP menu, the
Start key functions as a Select key to select the highlighted item
from the OCP menu.
Start
Cancel Key
Pressing Cancel causes the job that is currently printing to quit. In
addition, the printer automatically goes into the Offline mode after
the current printing job has quit.
Cancel
On/Off Line Key This key toggles between the Online and Offline modes. If you press
this key when the printer is in the Online mode, the printer goes into
the Offline mode. If you press this key when the printer is in the
Offline mode, the printer goes into the Online mode.
On/Off Line
Menu Key
Pressing this key activates the menu for the OCP when the printer
Menu
is in the Offline mode.
Arrow Keys
When using the OCP menu, the Cancel key functions as a Right
Arrow, the On/Off Line key functions as an Up Arrow and the
Menu key functions as a Down Arrow.
Select Key
When using the OCP menu, the Start key functions as a Select key
to select the highlighted item from the OCP menu.
Select
Power
Power Light
The power light illuminates to indicate that the main power for the
printer is on.
Error Light
The error light illuminates to indicate that a printer error occurred.
Error
Standby Light
The standby light illuminates to indicate that the printer has been
shut down from the OCP and is now in the Standby mode, waiting
for Start to be pressed.
Standby
October 2002
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Menu
The menu allows you to access other printer features.
NOTE: To access the menu, the print queue must not have any pages waiting to
be printed.
1. Press On/Off Line to take the printer offline.
2. Press Menu.
Printer Offline Feature
This feature is useful when you need to access the printer OCP menu.
When the printer is offline, it cannot send jobs to the processor or accept jobs
from the host.
To take the printer offline, press On/Off Line on the OCP. If a job is printing when
you take the printer offline, the job will complete printing. When you put the printer
back online, the sheet will be sent to the processor.
Online Mode
The Online mode is the normal mode and must be activated for the printer to
accept print jobs from the host computer.
Offline Mode
When the printer is in the Offline mode it cannot accept print jobs from the host
computer and will not send any sheets to the processor. When an error occurs,
the printer is automatically placed into the Offline mode.
Cancelling Jobs
To cancel the sheet currently being printed, press Cancel on the OCP. After the
sheet has been cancelled, the printer automatically toggles to the Offline mode.
To cancel all jobs waiting to be printed:
1. Press Cancel on the OCP to cancel the sheet that is currently printing.
2. Press Menu twice.
Printing Deferred or Buffered Jobs
“Pages Deferred” displays on the OCP and a number other than zero displays in
the Pages Waiting field when one or more jobs are waiting to be printed.
1. Press On/Off Line to take the printer offline.
2. Press Menu.
3. Press Start to print the jobs.
3-4
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Status Messages
Status messages display on the LCD display of the OCP to indicate the status or
current state of the printer.
Status Message/Printer State
Definition
status: ON LINE – Ready
The printer is idle and ready to accept jobs.
status: ON LINE – Processing
The printer is currently downloading a job,
processing a job.
status: ON LINE – Pages Deferred Pages are waiting and nothing is being
downloaded. If jobs were sent with the “Defer
Print” or “Buffer” option, the printer is waiting
for more data to fill the frame store.
status: ON LINE – Printing
status: OFF LINE – Idle
The printer is currently printing and may also
be processing more jobs.
The printer is currently offline. No jobs exist in
the printer. “Idle” is used instead of “Ready”
because the printer is actually idle (not doing
anything) and will not accept jobs.
status: OFF LINE – Processing
The printer is offline but a job is being
downloaded. A print cycle will not be initiated.
status: OFF LINE – Pages Deferred The printer is offline but there are jobs in the
printer that are waiting to be printed. A print
cycle will not be initiated.
status: OFF LINE – Printing
The printer will complete the current print cycle
and then pause.
status: OFF LINE – Cancelling
Cancel was pressed when the printer was
printing. The sheet that was printing was
immediately terminated. This message is also
displayed when you select “Yes” to the prompt
to cancel all remaining jobs when you enter
the menu.
status: Initializing
The printer is powering up (after Standby has
been pressed or the printer has been turned
on).
status: ON LINE – Resetting
The print engine is being reset because of an
error or operator intervention. The printer
returns to the “ON LINE – Ready” state after
the machine reset is complete (even if the
printer was offline because of an error or key
that was pressed before the reset).
status: Printer Error:
<Error Message>
A printer error (such as a paper jam) occurred.
The error message is displayed on the second
line of the display. For a complete list of error
messages, see “Printer Error Messages” on
page 5-2.
October 2002
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Loading Paper Into the Supply Cassette
WARNING: Move the supply cassette from the printer to a table to load or
unload paper.
One 10 to 20 inch supply cassette is included with the printer and is designed to
hold rolls of paper that are 25.4 cm, 27.9 cm, 30.4 cm, 50.8 cm and A4 widths.
Removing the Supply Cassette
1. Open the paper supply door.
2. Unlock the cassette clamp for the supply cassette.
3. Remove the empty supply cassette.
supply cassette
cassette
clamp
paper supply door
3-6
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Loading Paper into the Supply Cassette
1. Unlock the supply cassette.
2. Open the supply cassette.
3. If necessary, remove paper scraps from the core support assembly.
4. Remove the old core and support assembly from the supply cassette.
NOTE: Keep the felt surfaces clean to prevent scratches on the paper.
old core and core support assembly
felt
felt
supply cassette locks
5. Remove the screw lock and the old cardboard core from the core support
assembly.
6. Move the screw adjuster to the correct position for the paper size you are
loading. Pull the metal spring for the screw adjuster away from the gear and
slide the screw adjuster to the correct position until it locks into place in the
detent.
screw adjuster
cardboard core
gear
screw lock
core support
assembly
October 2002
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
TIP: Practice the following steps in the light with an empty cardboard core
before you load a new roll of paper in the dark.
CAUTION: Loading paper into the paper cassette must be completed in
a darkroom with the lights off.
7. Position the paper so that the lead edge of the paper is away from you.
8. Insert the core support assembly into the roll of paper as shown.
9. Push the cardboard core toward the gear until it engages the detent.
detent
cardboard core
10. Install the screw lock onto the core support assembly and ensure that it is
snug.
CAUTION: Do not overtighten the screw lock.
11. Place the core support assembly with the full paper roll into the supply
cassette.
3-8
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
IMPORTANT:Make sure that the right and left edges of the paper on the paper
roll remain aligned. Do not allow the roll of paper to slide or
“telescope.”
screw lock
12. Feed the lead edge of the paper through the slotted opening in the paper
cassette.
lead edge of the paper
slotted opening
image or emulsion
side
core support assembly
(side without the gear)
13. Close the supply cassette and latch the supply cassette locks.
NOTE: Be sure that the core support assembly rotates freely in the supply
cassette and that the paper feeds freely.
October 2002
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
supply cassette lock
When the paper cassette is locked, you can turn on the room lights.
IMPORTANT:When moving the supply cassette, pick up and carry the cassette
by both handles to prevent the paper from sliding or “telescoping”
to one side.
Installing the Supply Cassette
2. Check the knife and, if necessary, remove the trail edge of the paper from the
previous roll through the chad area.
paper supply door
knife
chad area
sheet transport
door
chad
3. Close the sheet transport door.
4. Open the paper supply door.
3-10
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
5. Align the slot on the bottom of the supply cassette with the plate on the bottom
of the shelf and slide the full supply cassette into place on the shelf.
shelf
Emulsion
(image) side of
paper
plate
cassette clamp
slot
6. Check that the gear on the supply cassette aligns and meshes with the gear
on the printer.
7. Lock the clamp to secure the supply cassette into place.
8. Ensure that the cut on the lead edge of the paper is straight.
CAUTION: Use scissors to cut the paper. Knives and razor blades will
shred the paper.
9. Press Start on the OCP.
10. When prompted, enter the number of feet on the roll of paper.
11. When the message “Feed paper into printer...” appears, pull the lead edge of
the paper out of the supply cassette and place it under the idler roller.
12. Feed the lead edge of the paper into the printer until you feel it being pulled.
Keep the left edge of the paper against the paper alignment guide.
IMPORTANT:Guide the paper into the printer while pressing down each edge
to prevent slack in the paper.
October 2002
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
CAUTION: If the paper does not load properly or a paper jam occurs,
press Cancel. Remove any paper from the shoe area and
square.
lead edge of
the paper
paper alignment
guide
idler
roller
gear on the
cassette
cassette
clamp
gear on the
printer
13. Close the paper supply door. The paper automatically feeds into position for
printing and the fogged section at the lead edge of the roll is trimmed off. The
message “Status: ON LINE – Ready” appears when initialization is complete.
3-12
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Reaching the End of the Roll of Paper
When the end of the roll of paper is reached, the OCP displays one of two
messages:
•
“Out of paper, open supply door to load...” — indicates that the supply
cassette is empty. To remove the paper, open the supply door and pull the
paper out of the shoe.
•
“End of roll, remove sheet from sheet transport” — indicates that the
supply cassette is empty. In this situation, the paper cannot be reversed into
the roll supply area since the trail edge of the paper has moved into the shoe.
The remaining paper is then moved forward into the sheet transport area with
the lead edge of the paper just beyond the knife. To remove the paper, grasp
its lead edge and pull it out of the shoe.
NOTE: If necessary, gently push the deflector down and use the shoe exit roller
knob to advance the paper into the chad area.
deflector
paper
shoe exit roller knob
October 2002
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Removing the Chad
Chad is wasted paper that is cut from the lead edge of the paper roll by the knife.
It is deposited in the chad area of the printer.
chad area
sheet transport
door
chad
This waste is usually necessary to remove fogged paper (paper that has been
exposed to light). The waste may also be necessary to ensure a straight lead
edge on the roll of paper and accurate positioning of the lead edge in the shoe.
Chad is cut from the roll when:
•
•
•
new paper is installed in the printer
the printer is reinitialized after one of the printer doors has been opened
the printer is reinitialized to ensure a square lead edge on the paper roll
IMPORTANT: Open the sheet transport door and remove the chad from the chad
area every time you load a new roll of paper into the printer.
Handling and Storing the Paper
Follow the instructions included with the paper for storing and handling the paper
properly.
IMPORTANT: Avoid storing paper in low humidity conditions.
Storing Paper Using the Soft Shutdown Feature
The Soft Shutdown feature (see “Shutting Down the Printer” on page 2-11) causes
the rollers to automatically reverse to rewind the lead edge of the paper to the first
metering roller during the soft shutdown process.
3-14
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Accessing the Printer Features
Shutdown and Restart
Shutdown
1. Select “Shutdown” from the main menu on the OCP.
2. Select “Shutdown NOW?”
This causes the printer to shut down operations and enter the standby mode.
Restart
1. Select “Restart” from the main menu on the OCP.
2. Select “Restart NOW?”
This causes the printer to immediately shutdown operations and reboot.
IMPORTANT:This shutdown is not a soft shutdown and does not save the
parameter settings that have been made since the previous
startup. Also, using this feature may cause a black line on the
paper in the shoe.
Unload Supply
1. Select “Unload Supply” from the main menu.
2. Select “Unload Supply NOW?”
The printer enters its unload paper sequence. When the unload paper
sequence is complete, the OCP returns to the main menu.
3. Select “Exit” to return to the OCP display. You are prompted to load another
roll of paper into the printer.
Selecting SCSI Ports
1. Select “Setup” from the main menu on the OCP.
2. Select “Ports”.
3. Select “SCSI”.
4. Select “SCSI Target ID”.
5. Use the Up and Down Arrows to select a new SCSI ID. The allowable SCSI
IDs are 0, 1, 2, 3, 4, 5, 6, 7.
6. Press Select to select/set the new value.
7. Select “Exit” to return to the previous menu on the OCP.
October 2002
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Selecting the Target Pad Read Options
1. Select “Setup” from the main menu on the OCP.
2. Select “Ports”.
3. Select “SCSI”.
4. Select “Target Pad Reads”.
5. Use the Up and Down Arrows to select “Yes” or “No” to indicate whether or
not the SCSI device driver will pad initiator read requests with zeros to the
requested length or terminate the SCSI read transaction when it has sent only
the data it has to send.
6. Press Select to select/set the new value.
7. Select “Exit” to return to the previous menu on the OCP.
Managing a Modem
Resetting the Modem Port
1. Select “Setup” from the main menu on the OCP.
2. Select “Ports”.
3. Select “Modem (Diag)”.
4. Select “Reset Port”.
5. Select “Reset Modem Port Now”.
NOTE: This causes the modem port to be set to its original factory setting.
6. Select “Exit” to return to the previous menu on the OCP.
Checking for a Modem
NOTE: This causes the printer to query the modem port for the presence of a
modem.
1. Select “Setup” from the main menu on the OCP.
2. Select “Ports”.
3. Select “Modem (Diag)”.
4. Select “Check Presence”.
5. Select “Check Modem Presence Now”.
6. Select “Exit” to return to the previous menu on the OCP.
3-16
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Setting the Printer Time and Date
Setting the Current Time
1. Select “Setup” from the main menu on the OCP.
2. Select “Time”.
3. Select “Current Time”.
4. Use the Up and Down Arrows to select a new time.
5. Press Select to save the new value.
6. Select “Exit” to return to the previous menu on the OCP.
Setting the Current Date
1. Select “Setup” from the main menu on the OCP.
2. Select “Time”.
3. Select “Current Date”.
4. Use the Up and Down Arrows to select a new date.
5. Press Select to save the new value.
6. Select “Exit” to return to the previous menu on the OCP.
Setting the Current Day
1. Select “Setup” from the main menu on the OCP.
2. Select “Time”.
3. Select “Day”.
4. Use the Up and Down Arrows to select a new day.
5. Press Select to save the new value.
6. Select “Exit” to return to the previous menu on the OCP.
Setting the Paper Length
The value displayed is the length of paper (in feet) that remains on the supply roll.
This number should be edited when a new or partially used paper roll is installed
in the printer. You receive a prompt to enter this number when a new roll is being
loaded into the printer. The range for paper is 0 to 999.
1. Select “Setup” from the main menu on the OCP.
2. Select “Paper”.
3. Select “Current Length”.
4. Use the Up and Down Arrows to select a new length for the paper.
5. Press Select to select/set the new value.
6. Select “Exit” to return to the previous menu on the OCP.
October 2002
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Selecting the Slug Width for the Paper
You can determine the width of the lead and trail edge borders on the prints by
selecting the slug width. The slug width is the total width of the lead and trail edge
borders (white space) of the paper that remains between the sheets of paper.
1. Select “Setup” from the main menu on the OCP.
2. Select “Printer”.
3. Select “Slug Width”.
4. Use the Up and Down Arrows to select a new slug width.
The slug width range is 0 to 250 pixels (0 to 1 inch).
5. Press Select to select/set the new value.
6. Select “Exit” to return to the previous menu on the OCP.
IMPORTANT:The lead and trail edge cannot be borderless. The slug width
should be at least 32 pixels (0.125 inches).
Example: image size=20 inches, slug width=0.25 inches (total for lead/trail edge)
0.125 inches
0.125 inches
Example: image size=four 8 inch images printed during one print cycle
___________
represents the cut edge
_ _ _ _ _ _ _ _ _ _
represents the image boundary
3-18
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Setting the Page Starts Value
The value for “page starts” indicates the number of pixels between the back wall
of the printer and the edge of the image. For example, when the printer begins to
print, it moves the print head to the back wall of the printer and then advances it
toward the front of the printer by the number of pixels specified in the “page starts”
parameter (value).
The “page starts” value is set so that the image edge closest to the back of the
printer will print off the paper and will then be borderless on the back edge of the
print.
NOTE: If the image size is wider than the paper, the front edge of the image will
also be borderless.
1. Select “Setup” from the main menu on the OCP.
2. Select “Printer”.
3. Select “Page Starts”.
4. Select the page start you wish to modify.
5. Use the Up and Down Arrows to select a new page start value.
6. Press Select to select the new value.
7. Select “Exit” to return to the previous menu on the OCP.
October 2002
3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Producing Borderless Prints
To achieve borderless prints on both the front and back edges of the paper, you
must set the Page Starts value to adjust the location of the image so that both
edges of the image print off the paper.
NOTE: The image width should be at least 76 pixels wider than the width of the
paper to ensure a borderless print.
Paper Size
Image Width in Pixels
10 inch
11 inch
12 inch
20 inch
A4
2576
2826
3076
5076
3000
outline of the paper
outline of the image
page start
back edge
front edge
If white borders are present on either the front or back edge of the print:
1. Measure the white border at both the lead (distance A) and the trail edge
(distance B) and determine its average width.
2. Convert the average width of the white border to a pixel value. To do this,
multiply the width by 250 and add 76.
3-20
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
3. Adjust the page starts value to the calculated pixel value. If the white border is
on the:
• back edge: reduce the page start value by the pixel value
• front edge: increase the page start value by the pixel value
distance A
cut edge
distance B
cut edge
IMPORTANT:The page start value for each paper width is different.
October 2002
3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Accessing the Software Version Number
To view the software version of the FEE, PEC and OPC circuit boards:
1. Select “Setup” from the main menu on the OCP.
2. Select “Printer.”
3. Select “More.”
4. Select “Version” to view the version number for the FEE, PEC and OPC
circuit boards.
5. Select “Exit” to return to the previous menu on the OCP.
Setting the Copyright Detection Feature
The Copyright Detection feature is designed to protect the copyrighted images of
professional photographers. This feature is applied to prevent images from being
duplicated.
1. Select “Setup” from the main menu on the OCP.
2. Select “Printer.”
3. Select “Copyright Detection.”
4. Use the Up and Down Arrows to select “Always On”, “Always Off” or “Host
Select.”
Host Select
Always On
Always Off
Copyright Detection
can be enabled or
disabled by the host on image that is
Copyright Detection is
enabled for every
Copyright Detection is
disabled for every
image that is
a print by print basis
for each image that is
downloaded to the
printer.
downloaded to the
printer.
downloaded to the
printer.
5. Press Select to select/set the setting for the new option.
6. Select “Exit” to return to the previous menu on the OCP.
3-22
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Resetting the Defaults
Resetting the Parameters
This procedure resets the parameters of the printer to the factory setup (default)
values. To indicate that the values have been reset to the factory setup values, the
word “done” is displayed in parenthesis after “Reset Parameters To Factory” on
the menu.
NOTE: Diagnostic parameters are not reset by this action.
1. Select “Setup” from the main menu on the OCP.
2. Select “Defaults”.
3. Select “Reset Parameters to Factory”.
4. Select “Exit” to return to the previous menu on the OCP.
Resetting the Printing LUTs
This procedure resets the Printing LUTs stored in nvram to the factory setup
(default) values. To indicate that the values have been reset to the factory setup
values, the word “done” is displayed in parenthesis after “Reset Printing LUTs To
Factory” on the menu.
1. Select “Setup” from the main menu on the OCP.
2. Select “Defaults”.
3. Select “Reset Printing LUTs to Factory”.
4. Select “Exit” to return to the previous menu on the OCP.
Resetting the Copyright Detection LUTs
This procedure resets the Copyright Detection LUTs stored in nvram to the factory
setup (default) values. To indicate that the values have been reset to the factory
setup values, the word “done” is displayed in parenthesis after “Reset Copyright
LUTs To Factory” on the menu.
1. Select “Setup” from the main menu on the OCP.
2. Select “Defaults”.
3. Select “Reset Copyright LUTs to Factory”.
4. Select “Exit” to return to the previous menu on the OCP.
October 2002
3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Changing the Units of Measurement for Paper Sizes
1. Select “Setup” from the main menu on the OCP.
2. Select “Printer”.
3. Select “More”.
4. Select “Units”.
5. Select “Units” again.
6. Use the Up and Down Arrows to select either “English” or “Metric”.
7. Press Select to select/set the new value.
IMPORTANT:Select “Exit” to return to the previous menu on the OCP.
About Printing
•
A print job is not printed until it is completely downloaded to the printer.
Print jobs are printed in the order they are received.
•
•
If multiple copies of a print job are requested, they are positioned next to each
other down the length of the roll, regardless of the width of the image.
•
It takes the same amount of time to print (expose the paper) a length of 6.5
inches as it does to print 33 inches.
Image Size
The minimum image length is 6.5 inches (1625 pixels). White space is
automatically added to images smaller than 6.5 inches to increase the image size
to this minimum.
The minimum sheet length is 8 inches. A sheet that is cut for an image less than
this size will have white space added to it to increase it to this minimum length.
The maximum image length is approximately 33 inches (8248 pixels).
Buffered and Unbuffered Jobs (or Immediate and
Deferred)
Jobs can be stored in memory when downloaded from the host until enough jobs
are downloaded to maximize the printing that occurs during the print cycle.
Most host applications have an option to indicate whether to print the job as soon
as it completes downloading to the printer or to wait until the printer has a full
buffer to print.
If the print job is sent to the printer with the Unbuffered/Immediate option, the job
will be printed as soon as it completes downloading to the printer. Regardless of
the number of (or size of) the jobs in the printer waiting to print, jobs sent with this
option are printed separately.
3-24
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
If the print job is sent to the printer with the Buffered/Deferred option, this indicates
to the printer to wait until it has a full buffer before printing. A full buffer is 26.5 to
33 inches. A print job sent with this option is printed when:
•
•
•
the buffer is full
the next print job received will not fit within the full buffer length
the next print job received is requested to be printed unbuffered/immediate
(the job received this way is printed by itself)
•
•
the next page)
the buffer is full and the next print job has started downloading to the printer
NOTE: If your host application needs to wait until a print job has been completely
downloaded to the printer before it can begin processing the next print job,
this option should not be used with larger width paper. It will slow down the
productivity of your system.
Printing Deferred or Buffered Jobs
“Pages Deferred” displays on the OCP and a number other than zero displays in
the Pages Waiting field when one or more jobs are waiting to be printed.
1. Press On/Off Line to take the printer offline.
2. Press Menu.
3. Press Start to print the jobs.
Host Software Functions Supported by the Printer
The printer supports bar coding and pixel doubling, which may be available
through your host software. Check the documentation for your host software to
see if these functions are available and how to use them.
Bar Coding
The bar coding function can be used for order tracking, package cutting (for
example: Type 208), etc.
Pixel Doubling
The pixel doubling function can be used to double the size of an image.
October 2002
3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Operating the Processor
Operator Control Panel
The operator control panel (OCP) for the processor allows you to view and
control:
•
•
•
•
•
•
•
chemical and dryer temperatures
development time
chemical replenishment rate
current day and time
automatic startup and shutdown times
equipment status checks
error messages
LCD display
current mode
current
feature
Set key
information
- - - SET - - -
MON OFF 15:00
SET
LED indicator
lights
Up and
Down
Arrows
blue function keys
Reset keys
The keypad on the OCP is covered with a plastic overlay and can be easily wiped
clean using a damp cloth. The display is a two-line liquid crystal display (LCD).
The top line indicates whether the processor is in the View, Set, Calibrate or Min
Max mode. The bottom line indicates the current feature information, menu
selections, etc. and is called the working line.
View Mode
The View mode is the normal screen mode. In this mode current processing
conditions, device settings and messages from the processor can be viewed.
Set Mode
The Set mode is used to change the operation settings of the processor.
Calibrate Mode
The Calibrate mode is used to calibrate devices and ensure that the processor is
accurately tracking and displaying equipment conditions.
Min Max Mode
The Min Max mode is used to view the minimum and maximum readings for the
device that is current.
3-26
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
OCP Key/Light Descriptions
Key /LED
Indicator Light
Key/Light
Description/Function
Set Key
Pressing Set causes the screen to change from View mode to either
Set mode, Calibrate mode, or Min Max mode. In Set mode, a device
can be set to “ON”, “OFF” or “AUTO” or a new operating parameter
can be entered. In Calibrate mode, an adjustment offset for the
device can be entered. In Min Max mode, the maximum and
minimum readings for the device can be viewed or reset.
SET
Up Arrow
The Up Arrow has two functions depending on the keyboard mode.
In View mode, this key is used to scroll the viewing screen that
displays additional devices or information. In Set or Calibrate
modes, this key increases the displayed value.
Down Arrow
The Down Arrow has three functions depending on the keyboard
mode. In View mode, this key is used to scroll the viewing screen to
display additional devices or information. In Set or Calibrate modes,
this key decreases the displayed value. In Min Max mode, this key
resets the values to the current measured temperature.
On/Off Key and Pressing On/Off turns the processor on and off. The light above
On/Off Light
On/Off illuminates continuously when the processor is ready. If the
chemistries are not all at their set temperature when the processor
is on, the light blinks on and off. When the processor is off, the light
is not illuminated.
Time Key and
Time Light
Pressing Time accesses the Time screen. The light above the key
illuminates when the Time screen is active.
Temperature
Key and
Pressing Temperature accesses the Temperature control screen.
The light above the key illuminates when the screen is active.
Temperature
Light
Replenishment Pressing Replenishment accesses the Chemical Replenishment
Key and and Wash Control screen. The light above the key illuminates when
Replenishment the screen is active.
Light
October 2002
3-27
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Key /LED
Key/Light
Description/Function
Indicator Light
Drive Key and
Drive Light
Pressing Drive accesses the drive motor control system. The light
above the key illuminates when the Drive key is active.
Material Key and The Material key is used to access the Material Transport screen.
Material Light
The Material key can also be used to view the processor setup
parameters, select the control strip screen, and start the control strip
above the Material key illuminates when the Material Transport
screen is active. If paper is present at the feed table, the LCD
display on the OCP indicates the size of the paper currently at the
entrance of the processor or at the exit. For example:
NOTE: Moving dots illuminate under the size indicators to indicate
that paper is moving through the processor.
Reset Keys
The Reset keys are the two embossed unmarked keys below the
Power and Material keys. Pressing both Reset keys simultaneously
puts the processor in Reset mode.
Status Messages
Status messages display on the LCD display of the operator control panel to
indicate the status or current state of the processor.
3-28
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
OCP On/Off Light
The on/off light switch for the OCP illuminates or deilluminates the entire OCP.
on/off light switch
October 2002
3-29
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Operational Modes
There are three operational modes for the processor:
•
•
•
Operator
Key Operator
Service
To access the features of the processor, it must be in the correct operational
mode. The table below will help you determine the correct operational mode for
each feature.
Key
Operator
Mode
Operator
Mode
Service
Mode
Feature
Dryer Temperature
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Material Mode (A or B)
Clear Jam or Stopped
Control Strip
Current Time/Day Clock
Development Time
Chemical Temperatures
Replenishment Rates
Seven Day Timer On/Off Times
Manual Override of Devices
Calibration Settings
Calibration Cycles
Display of Minimum and Maximum Readings
Memory Dump
Setup Menu
3-30
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Adjusting the Key Switch Lock
The key switch lock is behind the front panel on the side of the OCP.
key switch lock
The following key switch positions determine the operational mode and the
available feature:
•
•
•
Locked—Operator mode
Unlocked—Key Operator mode
Service—Service Technician mode
Key and Key Switch lock
(side view)
Key Positions
key switch
lock
key
Operator Mode
(locked)
Key Operator Mode
(unlocked)
(key rotates left and right)
Service Mode
Position
October 2002
3-31
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Processing a Control Strip
CAUTION: Loading the control strip feed box must be done in a darkroom in
complete darkness.
IMPORTANT: In the next step, make sure the emulsion side of the control strip is
facing up.
1. With the label on the control strip feed box facing up, feed one control strip
into the box.
2. Turn the knob on the control strip feed box counterclockwise until the strip is
completely inside of the box.
NOTES: – If the control strip is fed too far into the box, it jams in the box.
– The control strip feed box holds only one control strip at a time
– The lead edge of the control strip will be fogged.
3. Loosen the spring-loaded knob on the processor and pull it toward the
processor’s OCP.
4. Insert the control strip feed box into the bypass slot and release the spring
loaded knob.
5. Tighten the knob to lock the control strip feed box into place. Make sure the
box is flush with the processor top cover.
control
strip feed
box
bypass
slot
spring
loaded
knob
6. Press Material to select the Material screen.
7. Press Down to select the control strip option.
8. Press Set to access the Control Strip screen in Set mode.
NOTE: If the processor is not at the proper temperature, a control strip cannot
be run. The message “TEMP WAIT STRIP” appears until the chemistry
reaches the proper temperature.
9. Press Material to start the control strip procedure and cancel the Set mode.
3-32
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
10. Turn the knob on the control strip feed box clockwise with a steady slow
motion until the processor pulls the control strip or the knob moves freely.
11. After the control strip has been processed, loosen the spring loaded knob and
pull it toward the processor’s OCP.
12. Remove the control strip feed box from the bypass slot and release the knob.
13. Push the spring loaded knob toward the printer until the slot is completely
covered and tighten the knob.
NOTE: The processor will operate for two complete dry-to-dry cycles to allow
adequate time for the control strip to load. Replenishment is calculated
for 42 square inches of material.
Viewing/Setting the Processor Time and Date
Viewing the Current Time Setting
1. Press Time on the OCP to access the Time screen.
NOTE: All times have been entered using a 24-hour clock notation. For
example, 3:12 a.m. is entered and displayed as “3:12”; 3:12 p.m. is
entered and displayed as “15:12”.
2. Press a different blue function key to return to View mode.
Setting the Current Time
1. Press Time.
2. Press Set to enter the Time Set mode. Change the time of day by using the
Up and Down Arrows.
NOTE: The timing selections increase ordecrease in increments of one minute
each for the first 10 minutes in either direction. Thereafter the timing
selections increase (or decrease) in 10 minute increments.
3. Press Set twice or press a different blue function key to return to View mode.
Setting the Current Date
1. Press the blue Time key on the OCP.
2. Press Set twice to enter the Day Set mode. Change the day by using the Up
and Down Arrows.
3. Press Set once or press a different blue function key to return to View mode.
October 2002
3-33
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Viewing/Setting the Seven-Day Timer
The seven-day timer allows the processor to turn itself on and off automatically
throughout the week. If the processor is off and the day and time are the same as
an activate time setting, the processor automatically turns on. If the processor is
on and the current day and time match an off time setting, the processor turns off.
If a time is replaced with “not set”, that on/off time is ignored for that day.
The processor does not automatically turn on if the exit end circuit breaker has
been used to turn the processor off.
Viewing the On/Off Times
1. Press Time on the OCP to access the Time screen.
2. Use the Up Arrow to select the seven-day timer.
3. Use either the Up or Down Arrow to select the desired day and its on or off
time.
Setting the On/Off Times
1. Press Time on the OCP.
2. Press Set to put the Time screen in Set mode. Use the Up and Down Arrows
to change the on or off time. Press On/Off to toggle between an active or “not
set” mode.
3. Press a different blue function key to return to View mode.
Viewing the Software Identification
1. Press Time on the OCP to access the Time screen.
2. Press the Down Arrow to select the software identification screen.
3. Press Set once or press a different blue function key to return to View mode.
3-34
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Viewing/Setting the Temperatures
Viewing the Temperature Settings
1. Press Temperature on the OCP to access the Temperature screen.
2. Press the Up or Down Arrow to select the desired heater.
Setting the Temperature
1. View the temperature settings and select the desired heater.
2. Press Set.
3. Use the Up or Down Arrow to change the operating temperature.
4. Press Set to enter the Calibrate mode.
5. Press Set three times or press a different blue function key to return to View
mode.
NOTE: Press Temperature to toggle the heater between Manual Off and
Automatic mode.
Calibrating the Temperatures
IMPORTANT: Before calibrating a temperature sensor, make sure the
temperature has stabilized. The temperature near the probe is not
necessarily the same as the average temperature of the tank or
dryer.
1. View the temperature settings and select the heater.
2. Press Set twice to put the Temperature screen in Calibrate mode.
3. Use the Up or Down Arrows to enter an offset. Changing the offset causes
the displayed temperature to change. Adjust the offset until the displayed
temperature matches the actual temperature, as measured in the tank.
NOTE: Record and save the calibration value so it can be re-entered if the
memory is cleared.
4. Press Set twice or press a different blue function key to return to View mode.
Resetting the Min Max Temperatures
1. View the temperature settings and select the desired heater.
2. Press Set three times to enter the Min Max mode.
3. Press the Down Arrow to reset the values for the minimum and maximum
temperatures.
4. Press Set once or press a different blue function key to return to the View
mode.
October 2002
3-35
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Viewing/Setting Replenishment Settings
Viewing the Replenishment Rate
1. Press Replenishment to access the Replenishment screen.
2. Press the Up or Down Arrow to select the desired replenishment pump or the
wash/stabilizer tanks.
Setting the Chemical Replenishment Rate
1. Select the desired replenishment pump.
2. Press Set to access the Set mode.
3. Use the Up or Down Arrow to change the replenishment needed for each
square foot of paper processed.
4. Press Set twice or press a different blue function key to return to View mode.
NOTE: Press Replenishment to toggle the pump to Manual on, Manual off or
Per-Square-Foot mode.
Setting the Wash Replenishment Rate
1. Select the desired wash/stabilizer tank.
2. Press Set to access the Set mode.
3. If the wash is in per-square-foot mode, use the Up or Down Arrow to change
the amount of wash solution needed for each square foot of paper processed.
NOTE: In Automatic mode, the wash solution is on whenever material is in the
processor.
4. Press a different blue function key to return to View mode.
NOTE: Press Replenishment to toggle the pump to Manual on, Manual off,
Per-Square-Foot, or Automatic mode.
Calibrating the Replenishment Flow Rate
NOTE: Turn the key switch to the service position before you calibrate the
replenishment flow rate.
IMPORTANT: Before calibrating a flow rate, position the desired replenishment
tube into a beaker to catch the pump’s output or the wash tank’s
overflow. Make sure the beaker is large enough to catch the output
of the pump for at least 10 replenishment bursts of one second
duration. The pump may make more than one revolution during a
single burst period.
Measuring the Flow Rate
1. Select the desired replenishment pump.
2. Press Set twice to access the Replenishment screen in the Calibrate mode.
3. Press Replenishment to initiate a 10-second auto calibrate cycle for the
selected pump. After the cycle has completed, measure the output and divide
it by ten. This is the actual flow rate.
3-36
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Entering the Flow Rate
2. Press Set twice to enter the Calibrate mode.
3. Use the Up or Down Arrow to enter the measured flow rate.
4. Record and save the calibration values so they can be reentered if the
memory is cleared.
5. Press Set once or press a different blue function key to return the screen to
View mode.
Managing the Development Time
IMPORTANT: To prevent paper jams or image artifacts, operate the processor
development time within the recommended RA–4 specification—
45 seconds.
Viewing the Development Time
Press Drive to access the Drive Motor screen.
NOTE: If the drive is running, the current development time appears on the bottom
line. It is displayed in minutes and seconds. If not, the screen shows a
development time of “zero-00:00.”
Setting the Development Time
1. Select the Drive Motor screen.
2. Press Set to access the Drive screen in Set mode.
3. Use the Up or Down Arrow to change the set development time.
4. Press Set three times or press a different blue function key to return the
screen to View mode.
NOTE: Press Drive to toggle the drive motor between Manual on, Manual
off or Automatic mode.
Calibrating the Development Time
1. Run a cleanout sheet through the processor and use a stopwatch to
determine the actual time taken from entering the developer tank to entering
the bleach tank. If necessary, calibrate the processor.
2. Select the Drive screen.
3. Press Set twice to access the drive screen in the Calibrate mode.
4. Use the Up or Down Arrow to change the offset. As the offset changes, the
displayed development time changes. Increase and decrease the offset until
the displayed time matches the actual time. If necessary, choose an average
value for the offset.
5. Record and save the calibration value.
6. Press Set twice or press a different blue function key to return to View mode.
October 2002
3-37
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Displaying the Min Max Development Time
NOTE: The fastest and slowest development times, as recorded from the last time
the screen was reset, can be seen from this screen.
1. Select the Drive screen.
2. Press Set three times to access the Drive screen in Calibrate mode.
3. Press the Down Arrow to reset the Min Max values.
4. Press Set twice or a different blue function key to return to View mode.
Managing the Material Sensors
Material sensors are represented on the Material screen by solid or hollow circles.
There are four sensors at the feed end of the processor and one sensor at the exit
end of the processor. If a sensor detects material, its corresponding circle on the
material screen becomes solid. If no material is detected, the circle on the
material screen remains hollow. If there is material in the processor, shifting dots
are displayed at the bottom of the material screen, next to the circles that
represent the feed end sensors.
Viewing the Material
Press Material to access the Material screen.
Viewing the Processor Setup
1. Press Material to select the Material screen.
2. Press the Up Arrow to select the Processor Setup screen.
NOTE: The processor is currently operating using the development time,
replenishment rate and dryer setting for setup A, KODAK Digital.
Selecting the Processor Setup
1. Press Material to select the Material screen.
2. Press the Up Arrow to select the Processor Setup screen.
3. Press Set to access the Setup screen in the Set mode.
4. Use the Up or Down Arrow to change the operating setup.
NOTE: Changing the setup resets the development time, replenishment rates
and dryer setting to the values in the selected setup. The calibrations
are not affected.
5. Press Set or a blue function key to cancel the Set mode.
3-38
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Controlling the Processor Drive
Turning the Drive On
1. Press Drive.
2. Press Set.
3. Press Drive.
The drive is on.
Returning the Drive to Normal Operation
1. Press Drive.
2. Press Set.
3. Press Drive twice.
The speed value is displayed.
Computer Reset
Resetting the Processor
NOTE: Before resetting the processor, make sure you record the current settings.
You may need to reenter them.
1. Press both Reset keys simultaneously.
2. Press any blue function key to clear the machine reset message.
Loading the Defaults and Changing the Configuration
This procedure allows you to:
•
•
•
change the settings for the processor to metric values
change the tolerance specifications for temperature and development time
return all setting to their default values
IMPORTANT: Before loading defaults and change the processor configuration:
• Record all processor settings and calibrations.
• Turn the key switch to the service position.
Press and hold Set and both Reset keys. Release the Reset keys and then
release the Set key.
NOTE: The light above the left Reset key illuminates when both keys are pressed.
To save any changes and return to normal operation, reset the processor by
pressing both Reset keys simultaneously. Do not press Set.
October 2002
3-39
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Loading the Default Values
IMPORTANT: Record all processor settings before using this procedure.
Reloading the defaults causes the processor to be configured as
washless. The following settings and their calibrations return to
their original values.
• development time
• temperature settings
• replenishment rates
Press both Reset keys to save any changes to default settings and to return to
normal operation.
Changing the Wash/Stabilizer Setup
IMPORTANT: Record all setpoint and calibration data prior to using this
procedure.
1. Press and hold Set and both Reset keys. Release the Reset keys and then
release Set.
NOTE: The light above the left Reset keys illuminates.
2. Use the Up or Down Arrow to select the wash-stabilizer.
3. Press Set to access the screen in Set mode.
4. Use the Up or Down Arrow to change the operating setup.
5. Press Set to exit the Set mode.
6. To save the values, press both Reset keys simultaneously. Do not press Set.
NOTE: To make other changes, select the desired screen and enter new
values.
Changing the Metric/Fahrenheit Mode
IMPORTANT: Record all setpoint and calibration data for the processor prior to
using this procedure.
1. Press and hold Set and both Reset keys. Release the Reset keys and then
release Set.
2. Use the Up or Down Arrow to toggle to “Metricon”.
3. Press and hold the two black Reset keys.
4. When the processor begins to make a “beeping” sound, press the blue key.
The “beeping” sound will stop.
5. Press Set to reenter all setpoint and calibration data into the processor.
NOTE: Check that the temperature calibration is correct.
3-40
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
System Operating Procedures
Setting the Development Time Tolerance
A “DRIVE ERROR” message appears on the OCP when the development time is
slower or faster than the set speed by more than its set tolerance. The information
in this procedure enables you to change the tolerance.
1. Use the Up or Down Arrow to select the desired setup (A or B) and the
tolerance screen.
2. Press Set to access the screen in Set mode.
3. Use the Up or Down Arrow to adjust the acceptable tolerance range. The
adjustments are in one second increments.
4. Press Set to cancel the Set mode.
5. To save any changes and return to normal operation, press both Reset keys
simultaneously.
NOTE: To make other changes, select the desired screen and enter new
values.
Setting the Chemical Temperature Tolerance
This must be done by a qualified Kodak service person.
Clearing Error Conditions
Refer to the following procedures to clear error conditions:
•
•
•
“Clearing Drive Errors” on page 5-18
“Clearing Processor Paper Jams” on page 5-18
“Clearing a Reset Message” on page 5-17
October 2002
3-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Maintaining the Equipment
This chapter includes information you will need to maintain the KODAK
PROFESSIONAL RP 50 LED Printer and Processor. The topics are as follows:
Replacing the Air Filter .........................................................................4-3
Maintaining the Processor .................................................................................4-4
Chemistry Levels ..................................................................................4-4
Operational Checks ..............................................................................4-6
Main Drive Chain ................................................................................4-11
October 2002
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Maintaining the Printer
Daily Maintenance
Removing the Chad
Chad is the waste (fogged paper) that is cut from the lead edge of the paper roll by
the knife and deposited in the chad area of the printer.
Open the sheet transport door and remove the chad from the chad area several
times each day to prevent paper jams and ensure the proper movement of paper
from the printer to the processor. Also, check the knife and remove any small
strips of chad.
IMPORTANT: The chad should also be removed from the chad area every time a
new roll of paper is loaded into the printer.
chad area
sheet transport
door
chad
Calibrating the Printer
Calibrate the printer after every 8 to 10 hours of operation or when you change
paper emulsions.
NOTE: If the environmental temperature changes more than 5o Fahrenheit
(3o Celsius) since the printer was last calibrated, a calibration will be
necessary to maintain the image quality of the prints.
Follow the instructions for calibrating the printer. See “Calibrating the Printer” on
page 2-3.
4-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Periodic Maintenance
Replacing the Air Filter
The air filter under the shoe should be replaced approximately every 3 months.
1. Open the front door of the printer.
2. Pull back the spring fingers.
3. Remove the air filter.
4. Install a new air filter. For parts ordering information, see
“Supplies” on page A-1.
shoe
front door
spring finger
air filter
October 2002
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Maintaining the Processor
Daily Maintenance
Chemistry Levels
Check that the chemistry in the each of the processor tanks is up to the top of the
overflow pipe.
NOTE: If necessary, add warm water to the processor tanks to bring the fluid level
in the tank to the proper level.
chemistry
overflow
pipe
Replenishment and Effluent Chemical Levels
Before each run, check that the replenishment chemicals for the processor are at
a sufficient level to complete the run. Also, check the levels of the effluent (waste)
chemicals in the effluent bottles. If necessary, dispose of the effluent chemicals.
replenishment
and effluent
chemical bottles
4-4
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
CAUTION: To avoid having chemicals overflow from the effluent bottles, be
sure that the volume of chemicals in the replenishment bottles
does not exceed the remaining capacity of the effluent bottles.
Cleaning the Crossover Assemblies
Clean the crossover assemblies in the processor with a soft cloth to remove any
chemical residue on them. Install the splash guard see “Preventing Algae (for
Wash Configuration)” on page 4-8. Rinse the gears and socks with warm water
from a squirt bottle to dissolve deposits.
Operate the drive for the processor for at least 30 minutes before making prints or
running a control strip. This will ensure that the socks are thoroughly soaked with
chemistry.
October 2002
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Operational Checks
Check that the crossover assemblies and transport assemblies in the processor
are installed correctly and operating smoothly.
After performing all daily maintenance and before you begin to print jobs, run a
control strip to ensure that the processor is calibrated. See “Processing a Control
Strip” on page 3-32.
Testing
Before running the daily production jobs, run a control strip through the processor
and plot a graph of the results to determine if the equipment is operating properly.
See “Processing a Control Strip” on page 3-32.
If mottle (roller sock images) appears on the prints:
1. Check the levels of the chemicals in the processor tanks. If necessary, adjust
the levels of the chemistry.
2. Operate the processor drive for 30 minutes to allow the roller socks to
become saturated with chemistry.
4-6
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Weekly Maintenance
Checking the Tension of the Main Drive Chain
WARNING: Turnoffthemainpowerfortheprocessorontheoperatorcontrol
panel and at the circuit breaker to prevent injury from moving
parts and high voltage electricity and to prevent losing the
processor parameters.
Check that the tension on the main drive chain and all of the drive chains in the
transport assemblies of the processor is correct. If any drive chain has more than
0.50 in. of movement in the up and down direction, adjust the chain tension or
remove a link from the drive chain. To adjust the tension of the main drive chain,
change the position of the idler roller.
idler roller
main drive
chain
Checking the Circulation
Observe the circulation of the chemicals in the tanks to be sure that the chemical
pumps are working properly. If the chemicals are not circulating, replace the wash
and chemical filters. If necessary, call for service.
chemicals
October 2002
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Preventing Algae (for Wash Configuration)
Add hot water to the top rollers in the wash area of the processor to prevent algae
from forming and causing chemical and transport problems.
CAUTION: Install a splash guard over the entrance area of the processor to
prevent water and chemicals from entering the printer.
splash guard
top rollers
Cleaning the Crossover Assemblies and Transport Racks
WARNING: Always use two people to lift the transport rack (one person at
each end.)
Remove the crossover assemblies and the transport racks and wash them in
warm water. Be sure to wash the socks thoroughly using a soft bristle brush.
CAUTION: To prevent installing the transport racks in the wrong tank,
remove, wash, and replace each transport rack, one at a time.
crossover assembly
sock
transport rack
4-8
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Cleaning the Feed Table and the Processor Entrance Sensors
WARNING: Turn off the main power to the processor on the operator control
panel and at the circuit breaker to prevent injury from moving
parts and high voltage electricity and to prevent losing the
processor parameters.
1. Remove:
• top cover
• light tight cover
• developer entrance guide
top cover
light tight cover
developer entrance guide
feed table
entrance sensors
2. Clean the feed table and the processor entrance sensors with a clean damp
cloth or sponge.
October 2002
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Replacing Chemical and Wash Filters
Check the condition of the filters in the processor tanks. If necessary, replace
the filters.
NOTE: The filter for the developer is different than the filters for the other chemicals
and forthe wash. It can be identified bya grayring on itsend. See “Supplies”
on page A-1.
chemical/
wash
filter
Checking the Fittings for Leaks
Check all fittings for leaks. If necessary, tighten the fitting. Use a screwdriver to
tighten tube clamps.
CAUTION: Do not use tools to tighten the compression fittings. Use your
fingers to “finger tighten” these fittings.
4-10
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Monthly Maintenance
Main Drive Chain
WARNING: Turn off the main power to the processor on the operator control
panel and at the circuit breaker to prevent injury from moving
parts and high voltage electricity and to prevent losing the
processor parameters.
Grease the main drive chain in the processor with lithium grease.
main drive
chain
Checking the Temperature of the Solutions
After the warm-up period is complete, check that the temperatures of the solutions
in the processor are correct. If necessary, calibrate the temperature settings for
the solutions in the processor. See “Calibrating the Temperatures” on page 3-35.
Checking and Adjusting the Speed of the Processor
To determine if the processor is operating at the correct speed, run a cleanup
sheet through the processor while checking the elapsed time. If needed, adjust
the development time. See “Setting the Development Time Tolerance” on
page 3-41.
October 2002
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Periodic Maintenance
Cleaning Chemical Residue Buildup
The processor should be cleaned regularly to prevent corrosion and chemical
residue buildup, media transport problems, and contamination of the processing
baths.
The frequency of cleaning depends upon the operating environment. We
recommend that you include periodic cleaning in your workload schedule.
Always use warm water and a soft cloth to clean all surfaces.
Cleaning the Processor Tanks
The processor tanks need to be cleaned only when the residue buildup becomes
unacceptable to the operator and/or service personnel.
To clean the processor tanks:
1. Turn off the processor.
2. Insert the drainage hose for the tank into an empty effluent bottle.
3. Open the valve to drain the chemicals from the processor tanks.
top cover
valve
drainage
hose
empty
effluent
bottle
4. Remove the top cover from the processor.
5. Rinse the processor tanks with water.
October 2002
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Adding New Chemistry
The following information is a guideline for mixing new chemistry for chemical
tanks in the processor.
IMPORTANT: To avoid oxidation, do not use PRIME Developer or Bleach/Fix.
Developer: (FRESH START EKTACOLOR RA Developer RT)
1. Pour 8 litres of water in a 10 litre mixing bottle (bottle #1).
2. Follow the mixing instructions for parts A, B and C provided with the
developer. Add water until you reach the 10 litres mark.
3. Transfer 2000 ml of the pre-mixed developer replenisher to the developer
replenisher bottle (bottle #2).
4. Add 125 ml of developer starter to the mixing bottle (bottle #1).
5. Add water to the mixing bottle (bottle #1) until the mixture reaches the 10 litre
mark.
6. Add the mixture to the developer tank.
8. Transfer 6 litres of developer from bottle #3 to bottle #2.
9. Add 63 ml of developer starter to bottle #3.
10. Add 937 ml of water to bottle #3 and then stir the mixture gently.
11. Add the mixture to the developer tank.
NOTE: If the developer in the tank reaches the top of the overflow pipe before you
finish adding all of the developer starter, save the remainder of the
developerstarter. Addtheremaining developerstartertothedevelopertank
when the processor begins to operate. Air is purged from the circulation
lines and the level of developer in the developer tank drops. Discard any
remaining developer starter.
Developer/Replenisher: (EKTACOLOR RA Developer/Replenisher RT)
1. Pour 8 litres of water in a 10 litre mixing bottle.
2. Follow the mixing instructions for parts A, B and C provided with the
developer.
3. Add water until you reach the 10 litres and then stir the mixture gently.
Bleach Fix/Replenisher: (EKTACOLOR RA Bleach Fix/Replenisher)
1. Pour 5 litres of water in a 10 litre mixing bottle.
2. Follow the mixing instructions for parts A and B that are provided with the
bleach fix.
3. Add water to the mixing bottle until the mixture reaches the 10 litre mark and
stir the mixture gently.
4. Add the mixture to the bleach fix tank or to the replenisher.
4-14
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining the Equipment
Stabilizer: (EKTACOLOR PRIME Stabilizer and Replenisher)
1. Pour 9 litres of water in a 10 litre mixing bottle.
2. Add stabilizer [10 litre mix) to the water in the mixing bottle.
3. Add water to the mixing bottle until the mixture reaches the 10 litre mark and
stir the mixture gently.
4. Add the mixture to the stabilizer tank or to the replenisher.
Replenisher Additives:
1. Follow the instructions provided with the developer/replenisher additive.
2. Follow the instructions provided with the bleach fix/replenisher additive.
Recommended Processor Settings
Normal Paper Utilization (Under 120 sq/ft per day)
and
Low Paper Utilization (Under 72 sq/ft per day)
Tank/Dryer
Developer
Temperature
Replenishment Rate
37.200C
(990F)
25 ml per sq/ft
35.000C
(950F)
Bleach/Fix
Stabilizer
Dryer
20 ml per sq/ft
90 ml per sq/ft
NA
35.000C
(950F)
40.550C
(1050F)
High Paper Utilization (Over 300 sq/ft per day)
Tank/Dryer
Developer
Temperature
Replenishment Rate
37.200C
(990F)
23 ml per sq/ft
35.000C
(950F)
Bleach/Fix
Stabilizer
Dryer
20 ml per sq/ft
90 ml per sq/ft
NA
35.000C
(950F)
40.550C
(1050F)
NOTE: A minimum of 72 sq/ft of paper must be processed each day for process
control.
October 2002
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Diagnostics and Troubleshooting
This chapter describes the error messages for the KODAK PROFESSIONAL
RP 50 LED Printer and Processor and offers information for troubleshooting. The
information in this chapter includes:
Printer Error Messages ......................................................................................5-2
Manual or Automatic Reinitialization ...........................................................5-2
Printer Paper Path .......................................................................................5-3
Printer Error Messages ...............................................................................5-4
Miscellaneous Printer Error Messages .....................................................5-10
Clearing Printer Paper Jams .....................................................................5-11
Troubleshooting Observable Errors ..........................................................5-12
Additional Troubleshooting Tips for the Printer .........................................5-15
Processor Error Messages ..............................................................................5-16
Clearing Error Messages ..........................................................................5-17
Clearing a Reset Message ........................................................................5-17
Clearing Processor Paper Jams ...............................................................5-18
Clearing Drive Errors .................................................................................5-18
Additional Troubleshooting Tips for the Processor ...................................5-19
Calibration Troubleshooting .............................................................................5-19
Calibration Graph ......................................................................................5-19
Calibration Error Codes .............................................................................5-20
Non-Numeric Error Messages ...................................................................5-26
Getting Additional Help ....................................................................................5-27
October 2002
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Printer Error Messages
The following messages appear on the printer’s OCP when an equipment
problem occurs:
•
Error Messages–indicate an error condition that needs to be corrected
or resolved before you can resume operating the equipment.
(For example: “OUT OF PAPER”, “SUPPLY DOOR OPEN”)
Some error conditions may be easily corrected and some may require the
attention of a high level operator or even a service person.
•
Miscellaneous Error Messages–indicates a problem with the printer has
occurred that may or may not require you to call your service person.
More than one problem can occur at a time, however, only the message for the
first error will appear.
Manual or Automatic Reinitialization
The printer will reinitialize when you correct the problem that caused the error
code and press the Start key on the OCP within 30 seconds after closing the
printer door(s).
If you do not press the Start key within 30 seconds after closing the printer
door(s), the error message will disappear and the printer will automatically
reinitialize when you begin to print.
The reinitialization process includes:
•
•
•
Fogged Paper Cut—Fogged paper is cut from the lead edge of the paper roll
if the printer door was opened to correct an error.
Mechanical Self Check—A self-check of all mechanical systems in the
printer occurs.
Paper Check—A cut is made across the lead edge of the paper roll to ensure
a clean straight cut. The paper is then repositioned in the shoe.
5-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Printer Paper Path
The paper path through the printer is illustrated below. Use this information when
troubleshooting the printer.
WARNING: Do not touch the carriage. Use the translator knob to move the
carriage.
CAUTION: Do not use sharp objects on the shoe.
Rotate the flop preventer knob to move the flop preventer out of
the way before moving the carriage with the translator knob.
shoe exit roller
knife assembly
translator knob
metering roller
flop preventer knob
metering
roller
knob
SOL
(start of line)
EOL
(end of line)
deflector
shoe exit
motor knob
transport roller
rotor
carriage
shoe
shoe exit nip
paper cassette
October 2002
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Printer Error Messages
If the error message continues to occur after implementing the possible solutions
from the table below, call your service person.
Error
Code
Error Message
not initialized
Possible Cause
Possible Solution
Reinitialize the printer.
1
2
3
Attempting to perform a function
before the printer has initialized.
initializing err
busy
Attempting to perform a function
during the initialization process.
Wait for initialization to complete and
try the function again.
Attempting to perform a function
while the printer is busy performing
another function.
Wait for the previous function to
complete and try the function again.
4
5
out of paper
Paper cassette is empty and the
paper path sensors do not detect
paper.
Load a full paper cassette into the
printer.
end of roll at supply
paper already loaded
Printer has run out of paper and the
tail end of the paper has been
rewound to the paper supply area.
Remove the tail end of the paper at
the supply door and load a full supply
cassette into the printer.
6
7
“Load Paper” was selected when
paper was already loaded.
Solution not required.
Close the paper supply door.
Close the front door.
supply door open,
please close
The paper supply door was left
open.
8
front door open, please
close
The front door was left open.
9
back door open, please
close
The back door was left open.
Close the back door.
11
sheet detected in sheet
xport
• The processor is not ready to
accept paper.
• Check that the processor fully
takes a sheet of paper and
reinitialize the printer.
• A paper jam has occurred.
• The printer was reinitialized
while paper was being fed into
the processor.
• Check for a paper jam in the sheet
transport area.
CAUTION: Always pull the
sheet of paper out from the
processor to avoid bringing
chemicals into the printer.
• If problem continues, call for
service.
12
13
14
motor busy
A low level motor move command
was issued while the timer motor
was in use.
Wait for the motor move to complete
or stop the motor and reissue the
command.
motor setup invalid
bad printer state
A low level motor move command
was issued while the timer motor
was in use.
Wait for the motor move to complete
or stop the motor and reissue the
command.
The printer cannot execute the
requested command.
Reinitialize the printer.
5-4
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Error
Code
Error Message
timers busy
Possible Cause
Possible Solution
15
A low level motor move command
was issued while the timer motor
was in use.
Wait for the motor move to complete
or stop the motor and reissue the
command.
16
17
18
20
timer spurious interrupt
code
A spurious (false) timer interrupt
has occurred.
No solution required.
No solution required.
Call for service.
command not
implemented
The function requested is not
supported in this software release.
unexpected OCP reply
The 300 board sent an unexpected
message to the 200 board.
pec service mode
The service switch for the 200
board is on, enabling on-board
LEDs that can cause fogging.
Call for service.
21
22
opc service mode
The service switch for the 300
board is on, enabling on-board
LEDs that can cause fogging.
Call for service.
end of roll, remove
paper at sht xprt
The paper cassette is empty and
tail of the paper has been fed into
the sheet transport area.
Pull the paper tail out of the sheet
transport area near the knife.
23
24
25
in error state
middle of load
wait proc
A previous error has not been
cleared.
Reinitialize the printer.
Attempting to perform a function
while paper is being loaded.
Wait until paper loading is complete
and perform the function again.
Attempting to perform a function
while the printer detects a problem
with the processor.
Turn on the processor. Wait for the
processor to warm up and then
reinitialize the printer.
26
27
28
xport back door open
xport front door open
unit does not fit
The back sheet transport door was
left open.
Close the back sheet transport door.
Close the front sheet transport door.
Begin printing.
The front sheet transport door was
left open.
The sum of all the unit setups since
the last print start exceeds 33
inches.
29
30
sheet fogged in sheet
xport
A door was opened while sending a
sheet from the printer to the
processor.
Reprint.
unexpected knife
neither limit
Knife not detected at either end.
Call for service.
31
64
door opened briefly
bad msg checksum
The door was opened and closed.
Reinitialize the printer.
Call for service.
A problem with a prom has
occurred.
October 2002
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Error
Error Message
Code
Possible Cause
Possible Solution
65
proc stopped taking
sheet
The paper did not disappear from
the sheet transport area within the
expected amount of time. An error
may have occurred in the
processor.
• Clear a paper jam from sheet
transport (chad) area. See
• Wait a few minutes for the error
condition to be corrected.
• Reinitialize the printer and call for
service.
66
67
paper jam in shoe
Jam detect sensor detected
jammed paper at the shoe
entrance.
Remove jammed paper and reload
the paper.
rotor not up to speed
An obstruction in the shoe area
prevented the rotor from achieving
the correct speed in the expected
amount of time.
Wait for at least 1 minute, then clear
the obstruction in the shoe and
confirm that all doors are closed.
68
xltr hard limit detected
Either the front or back hard limit
switch was actuated.
• Move the translator off the front or
back hard limit switch. Use the
translator knob.
• Call for service.
69
70
unexpected xlator front
limit
The translator front limit switch was
detected unexpectedly.
Confirm that all doors are closed and
reinitialize the printer.
xlator front limit not
detected
The translator front limit switch was
not detected after moving translator
to the front of the printer.
Confirm that all doors are closed and
reinitialize the printer.
71
72
unexpected xlator back
limit
The translator back limit switch was
detected unexpectedly.
Confirm that all doors are closed and
reinitialize the printer.
xlator back limit not
detected
The translator back limit switch was
not detected after moving translator
to the back of the printer.
Confirm that all doors are closed and
reinitialize the printer.
74
75
76
paper present not
detected
Paper was detected at the
11 and 20 inch paper sensors but
not at the 10 inch paper sensors.
Check that the paper is loaded and
threaded properly.
unexpected 11 inch
paper
Paper was detected at the
11 inch paper sensor but not at the
10 or 20 inch paper sensors.
Check that the paper is loaded and
threaded properly.
11 inch paper not
detected
Paper was detected at the
Check that the paper is loaded and
threaded properly.
10 inch paper, 20 inch paper, shoe
entrance and the knife sensors but
not at the 11 inch paper sensor.
79
77
unexpected paper at
shoe entr
Paper was detected at the shoe
entrance sensor but not at the
paper width sensor.
Remove any paper from the shoe.
unexpected 20 inch
paper
Paper was detected at the
20 inch paper sensor but not at the
10 inch or 11 inch paper sensors.
Check that the paper is loaded and
threaded properly.
5-6
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Error
Code
Error Message
Possible Cause
Possible Solution
80
paper at shoe entr not
detected
During paper loading, the lead
edge of the paper was not detected
at the shoe entrance sensor within
the expected amount of time.
Load the paper in less time.
81
unexpected paper at
knife
• Paper jam occurred as paper
was being reversed from the
knife to the end of roll and paper
was detected at the knife instead
of at the shoe entrance.
Check that the paper is loaded and
threaded properly. Check for a paper
jam at the knife area.
• Paper sensor at knife or shoe is
not functioning correctly.
82
83
paper at knife not
detected
• Paper was not detected at the
knife when it should have been.
• Paper jam occurred.
• Paper sensor at knife or shoe is
not functioning correctly.
Check that the paper is loaded and
threaded properly. Check for a paper
jam at the knife area.
unexpected paper at
sheet xport
Paper is detected in the sheet
transport area when not expected.
• Remove any paper from the sheet
transport area.
• Check that the processor input
sensor is not blocked. If
necessary remove the paper from
the processor entrance.
84
85
86
87
paper at sheet xport not
detected
Paper was fed into the sheet
transport area but was not detected
by the sheet transport sensor.
Check that the paper is loaded and
threaded properly. Check for a paper
jam in the sheet transport area.
slack loop err, takeup
paper cinched?
The printer was unable to takeup
the slack loop because the paper
was not properly cinched.
Check that the paper is properly
attached to the cardboard core in the
takeup cassette.
slack loop high not
detected
Unable to detect slack loop.
Check that the paper is properly
attached to the cardboard core in the
takeup cassette.
timeout waiting to cinch
takeup
The printer door was not closed
within the normal amount of time.
Open the takeup door, attach the
paper to the cardboard core in the
takeup cassette and close the
takeup door.
89
90
91
unexpected deflector
nip up not detected
The deflector nip up switch was
detected after moving the deflector
to the down position.
• Check for a paper jam at the
sheet transport area.
• Reinitialize the printer.
knife front not detected
The front switch for the knife was
not detected after moving from front
to back.
Check for a paper jam at the knife
area.
deflector nip up not
detected
The deflector nip up switch was not
detected after moving the deflector
from the down position to the up
position.
• Check for paper at the sheet
transport area.
• Reinitialize the printer.
• Call for service.
October 2002
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Error
Error Message
Code
Possible Cause
Possible Solution
92
knife back not detected
Knifeback switch was not detected
after moving knife from front to
back.
Check for a paper jam at the knife
area.
93
95
translator power fault
error
A power fault was detected by the
translator puck.
Close all doors and reinitialize the
printer.
unexpected shoe exit
nip detected
The shoe exit nip made switch was
detected after moving the shoe exit
nip to the nip unmade position.
Check for a paper jam in the shoe
exit nip area.
96
97
98
99
shoe exit nip made not
detected
The shoe exit nip made switch was
not detected after moving the shoe
exit nip to the nip made position.
Check for a paper jam in the shoe
exit nip area.
unexpected deflector
nip made
The deflector nip made switch was
detected after moving the deflector
to the up position.
Check for a paper jam in the
deflector nip area.
deflector nip made not
detected
The deflector nip made switch was
not detected after moving the
deflector to the up position.
Check for a paper jam in the
deflector nip area.
timeout clearing data
patch
The rotor was not able to be
properly started.
Call for service.
100
101
102
109
xlator start failed
The translator failed to start.
The shoe exit nip failed to start.
The deflector failed to start.
Call for service.
Call for service.
Call for service.
Call for service.
shoe exit nip start failed
deflector start failed
sheet xport ready
timeout
The sheet transport area remains
busy or initializing process is taking
longer than expected.
110
111
112
128
paper detected in
machine
Paper was detected in the printer
while attempting to load a new roll
of paper.
Remove all paper from the printer
and reload the new roll of paper.
xlator home failed
The translator could not find its
home position after several
attempts.
Call for service.
invalid paper width
sensor coverage
The paper is not laying flat over the
paper width sensors or the end of
roll has been reached.
Open the supply door and move the
paper to the correct position.
back checksum 0
ROM test failed at powerup.
Reinitialize the printer and call for
service.
129
130
bad checksum 1
rotor not stopping
RAM test failed at powerup.
Rotor will not turn off.
Call for service.
Turn off the printer and call for
service.
131
xlator at both limits
Both the front and back translator
soft limit switches are actuated.
Call for service.
5-8
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Error
Code
Error Message
Possible Cause
Possible Solution
132
knife at both limits
Both the front and back knife limit
switches are actuated.
Call for service.
133
timeout sheet xport
reply
The 300 board does not reply to the
200 board within the expected
amount of time.
Call for service.
Call for service.
134
duart self test failed
Duart test failed when the printer
was turned on.
192
–
Various software error
messages.
A software problem has occurred.
Shut down and restart the printer.
Call for service.
219
October 2002
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Miscellaneous Printer Error Messages
Miscellaneous error messages indicate that a problem with the printer has
occurred that may or may not require you to call your service person.
Error
Code
Error Message
Possible Cause
Possible Solution
Close all doors.
256
257
258
259
260
door open, please close
The paper supply door was left
open.
machine control initialize
error
The printer did not initialize.
Reinitialize the printer and call for
service.
machine control initialize
timeout
The printer did not initialize in
time.
Reinitialize the printer and call for
service.
machine control reply
timeout
A machine control
communications error occurred.
Reinitialize the printer and call for
service.
proc stopped taking
sheet
The paper did not disappear from
the printer in the expected amount
of time. An error may have
• Clear a jam from sheet transport
(chad) area. See "Clearing Printer
• Wait a few minutes for the error
condition to be corrected.
occurred in the processor.
• Reinitialize the printer and call for
service.
261
time out waiting to feed
paper
• Paper did not feed in time
during loading.
• Paper was loaded incorrectly.
• Reload the paper.
• Reinitialize the printer and call for
service.
262
263
bad communications -
call service
A communications error has
occurred.
Reinitialize the printer and call for
service.
DMA timeout
Data being sent to the printhead
did not arrive in the specified
amount of time.
Reinitialize the printer and call for
service.
264
265
266
267
FIFO empty interrupt
Data was sent to the printhead too
quickly.
Reinitialize the printer and call for
service.
machine control state
timeout
A message from machine control
did not arrive in time.
Reinitialize the printer and call for
service.
failure creating test
image
The test image could not be
created.
Follow the instructions on the OCP.
paper/width mismatch,
end of roll
The paper installed is not wide
enough for the job(s) waiting in
the printer to be printed.
Install the correct paper cassette
with the correct width paper or
cancel all waiting jobs.
5-10
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Clearing Printer Paper Jams
Open the front door and front sheet transport door on the printer.
To remove a paper jam from the shoe when the lead edge of the paper is:
in the sheet transport area and
visible
not visible
1. Open the paper supply door and
follow the instructions on the door
label.
1. If the paper is not already cut,
manually move the knife across
the web to cut it.
2. Open the paper supply door and
follow the instructions on the door
label.
cut here
To remove a paper jam or sheet from the sheet transport area when the lead
edge of the paper is:
not visible and a paper jam in the
visible from inside the printer
processor has caused the
processor to stop
1. Pull the sheet out through the sheet
transport (chad) area.
2. Remove the sheet from the processor
or allow the lead edge of the paper to
enter the processor.
NOTE: This may require you to advance
the sheet into the processor.
CAUTION: Remove jammed paper from the printer by pulling the paper from
the paper supply area if the lead edge of the paper has not entered
the processor.
Do not remove the jammed paperthrough the sheet transportarea
if the lead edge of the paper has entered the processor. Remove
the jammed paper from the top of the processor.
Do not use sharp objects when clearing paper jams.
Do not leave small pieces of paper in the printer.
October 2002
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Troubleshooting Observable Errors
Observation
Possible Cause
Possible Solution
• The printer is difficult to The processor specifications are not Make sure that the processor is in control.
calibrate.
correct.
• The printer calibration
values are not correct.
The prints have bands.
• The processor is not calibrated.
• The processor has not been
maintained properly.
• Calibrate the processor.
• Make sure that the chemistry levels in the
processor tanks are correct.
• Run a control strip through the processor.
One or more of the crossover
assemblies in the processor is not
properly installed and is denting the
socks.
Install the crossover assemblies correctly.
NOTE: If necessary, replace the dented socks.
The printer was disturbed or
Do not disturb or bump the printer during a
bumped during a writing sequence. writing sequence.
The processor is not making enough Leave the processor drive on.
prints to keep the socks balanced.
A print has a line on it.
The circuit breaker was turned off
when paper was in the shoe.
• Do not turn off the circuit breaker when paper
is in the shoe.
• Do a shutdown prior to turning off the circuit
breaker.
The printer was disturbed or
bumped during the print cycle.
Do not disturb or bump the printer during the
print cycle.
The prints have a repeated The roll of paper was dropped on its Load a new roll of paper.
unfocused pattern on the
edges.
edge.
The edges are out of focus. The relative humidity level is too low Increase the humidity level in the room or store
for the paper to be stored in the
cassette for more than one day.
the paper in a sealed plastic bag when it is not
being used.
The prints have mottle on
them.
The processor needs maintenance. • Top off the processor tanks more frequently.
• Turn on the processor drive for 10 minutes to
saturate the roller socks with chemistry.
• Leave the processor drive on when not
printing.
The prints have a light leak The opening for the control strip
Close the opening for the control strip feed box
in the top cover of the processor.
exposure on them.
feed box is open.
Cassette opening exposed to bright Store and carry the cassette with the opening
light. facing down.
Paper slugs are on the
prints.
There is too much chad in the chad • Open the sheet transport door and remove
area.
the chad from the chad area.
• Remove any small strips of paper from the
knife area.
The rotor is hitting the
paper in the printer and
causing noise.
The paper is not loaded correctly.
Reload the paper.
5-12
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Observation
Possible Cause
Possible Solution
The vacuum reduction
insert is damaged and
causing noise in the printer.
• The vacuum reduction insert was Properly install an undamaged vacuum
not installed properly and has
become damaged.
reduction insert.
• A damaged vacuum reduction
insert was installed.
The paper is being creased The lead edge of the paper has not 1. Pull the paper out of the printer from the
and crumpled when
feeding into the printer.
been squarely trimmed and is being
pulled at an angle or unevenly or it is 2. Recut the lead edge of the paper squarely.
paper supply area.
being loaded at an angle into the
rollers.
3. Reload the paper. Wait for a message and
then push the paper evenly and slowly.
NOTE: If necessary, remove the curl in the
paper by rolling the paper on an empty
core in the opposite direction of the
curl.
The paper jams repeatedly. Small strips or pieces of paper are
caught in the printer from the
Remove small pieces of paper from the printer.
previous paper jam.
The prints have not been
cut correctly.
Strips of paper are caught in the
knife area.
Remove the strips of paper from the knife area.
The borders on the prints
are not the right size.
The slug width is not correctly set.
Reset the slug width, see “Selecting the Slug
Width for the Paper” on page 3-18.
The host software’s image
positioning is not correct.
Refer to the instructions for the host software.
The page start parameter may be
incorrect.
See the information for “Page Starts” in
the“Setting the Page Starts Value” on
page 3-19.
The edge(s) of the prints
are damaged and the
image is skewed.
• The paper is not loaded correctly 1. Reload the paper in the paper cassette.
in the paper cassette.
• The paper cassette clamp is not
secured correctly.
• The paper cassette was not
aligned with the pin when
installed on the shelf.
2. Position the paper cassette on the pin of the
shelf.
3. Close the cassette clamp to lock the paper
cassette into position.
NOTE: Always carry the paper cassette with
two hands to prevent the paper from
sliding to one end or “telescoping”.
4. When loading paper into the printer:
• cut the corners of the lead edges of the
• The paper cassette was not
picked up or carried correctly and
the paper has “telescoped”.
o
paper at a 45 angle
• wait for a message to feed
• push the paper slowly into the printer’s
rollers, keeping the paper taut between
the cassette and the rollers.
NOTE: Push the paper evenly so that the
paper remains flat and does not buckle
and do not push the paper too hard
against the paper alignment guide.
October 2002
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Observation
Possible Cause
Possible Solution
The host computer and the The SCSI cable has been disturbed. 1. Turn off the host computer and other SCSI
printer are not
devices.
communicating correctly.
2. Turn off the printer.
3. Disconnect the SCSI cable.
4. Reconnect the SCSI cable.
5. Power up the printer and wait for it to
initialize.
6. Power up the other devices.
7. Power up the host computer.
The host does not
An error was made during the power 1. Turn off the host computer.
recognize the printer
up sequence.
2. Turn off the printer.
3. Power up the printer and wait for it to
initialize.
4. Power up the host computer.
The SCSI IDs are different.
1. Change the SCSI ID through the OCP.
2. Turn off the host computer.
3. Turn off the printer.
4. Power up the printer and wait for it to
initialize.
5. Power up the host computer.
Repeated noise from the
processor.
The racks are installed incorrectly.
Reinstall the racks correctly. See “Operational
Checks” on page 4-6.
Prints have scratches on
them.
The processor racks and socks are • Clean the processor racks and socks.
contaminated (dirty).
• Check that the crossover assemblies are
installed correctly.
Chemistry has built up on
the printer exit rollers.
• Wet prints were pulled into the
printer to clear a paper jam.
(Usually following errors 65 or
260.)
• Clean the rollers with a damp cloth.
• Clear the paper jam.
• Use the splash guard when doing processor
maintenance.
• Splash guard was not used when
doing processor maintenance.
Chemistry leaks from the
processor.
Hose clamps or compression fittings Tighten the clamps and compression fittings.
are loose.
See “Checking the Fittings for Leaks” on page
4-10.
The text on the paper has
flare.
• The text density is too high.
• Reduce the density of the text by driving the
processor to the upper end of the control
limits.
• Calibrate the printer.
• The processor is not in control.
• The printer is not calibrated
correctly.
• Download the latest calibration software from
Kodak’s Web site and then calibrate the
printer.
5-14
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Observation
Possible Cause
Possible Solution
The supply or takeup door The latch on the door was pushed in Pull the latch back to its normal position with
will not close.
(flush with the door) when the door
was closed with too much force.
scissors and close the door with a normal
amount of force.
latch
Additional Troubleshooting Tips for the Printer
•
•
•
Check that the processor is turned ON and warmed up prior to printing.
Turn on the processor drive for 30 minutes before printing.
Be careful to correctly load, seat, and thread the paper into the paper
cassettes.
•
•
Be careful to correctly close all doors prior to printing. If doors are ajar or if
interlock switches are not closed, the printer will not print.
The error “sheet detected in sheet xport” may appear after reinitializing the
printer if the printer was in the process of sending paper into the processor. If
this occurs, wait until the sheet has been fully fed into the processor and then
reinitialize the printer again.
•
•
If the printer indicates that it is reinitializing after an error occurs and you have
not opened a door (but you do not hear the normal sounds of reinitialization
for up to 2 minutes) the printer may be waiting for the sheet to go into the
processor before attempting to reinitialize. Do not attempt to reinitialize the
printer again.
Before connecting or disconnecting the SCSI cable or terminator, turn off the
power for the printer and the host computer. Also, if you replace the SCSI
cable, remove the Ferrite bead from the existing SCSI cable and install it on
the new SCSI cable.
October 2002
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Processor Error Messages
Two types of messages appear on the OCP for the processor:
•
Error Messages—Indicate that a minor error condition has occurred or that
there is a problem during system monitoring. These messages may require
that you perform some action to correct the error. These errors are described
further in this section.
•
Status Messages—Indicate the status of the equipment or the procedure that
is occurring. These messages occur only when the processor is in the manual
mode and do not require any action from you. Status messages are not listed
in this chapter.
Error messages are displayed on the top line of the processor’s OCP. These
messages are accompanied with an audible alarm.
Error
Message
Possible Cause
Possible Solution
XXX probe fault The temperature probe could be either
short circuited or open circuited
Call for service.
XXX temp error
The temperature has been above or
below the set temperature for at least
20 seconds.
Press the Material key to reset the temperature.
time reset
The settings and calibrations for this
device have been reset to the factory
preprogrammed values.
Have the settings and calibrations checked by a
qualified technician.
temp reset
repl reset
The settings and calibrations for this
device have been reset to the factory
preprogrammed values.
Have the settings and calibrations checked by a
qualified technician.
The settings and calibrations for this
device have been reset to the factory
preprogrammed values.
Have the settings and calibrations checked by a
qualified technician.
drive reset
The settings and calibrations for this
device have been reset to the factory
preprogrammed values.
Have the settings and calibrations checked by a
qualified technician.
machine reset
drive error
The processor has been reset. Power
may have been disconnected.
Press any function key. If the message continues to
appear, call for service.
The drive motor speed has been out of
Press the Material key and clear the error. If the
specification for more than 20 seconds. problem continues to occur, call for service.
com error
The communications between the
keyboard display and the controller
have been disrupted.
Call for service.
paper jam
The processor did not detect paper that
Turn off the motor and remove the jammed paper.
should have been exiting the processor. Press the Material key and clear the jam.
exit blocked
The exit sensor detected paper
unexpectedly.
Remove the obstruction from the exit sensor.
5-16
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Clearing Error Messages
To clear an error or warning message from the OCP, the condition causing the
error or warning must be corrected. Paper jam, drive errors and temperature
errors must be cleared from the material function.
Clearing a Reset Message
If the processor is reset, the “MACHINE RESET” error message will appear on the
top line of the LCD display on the processor’s OCP. Press any function key to
erase the message.
If the processor is reset and the values for a function are reset to factory settings,
a reset message for that function will also appear (for example: “CLOCK
RESET”).
To clear a function reset message, press the function key for the function the
message refers to.
LCD display
MACHINE RESET
SET
function keys
October 2002
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Clearing Processor Paper Jams
jams in the printer.
The processor enters the jammed mode if it fails to detect material exiting the
processor at the expected time. In the jammed mode, the drive motor and
replenishment pumps are turned off and no material is processed.
1. Remove the top cover and light tight cover from the processor.
2. Cut the paper at the top of each rack.
CAUTION: To prevent contaminating the processor chemicals, do not let
the chemicals from the paper you are removing drip into the
other processor tanks that have different chemicals.
3. Remove the cut paper from each rack by pulling straight up.
4. Press the Material key to access the Material mode.
5. Press the Set Key and the Material key to activate the Clear Jam mode.
6. Press the Material key to operate the processor for two complete dry to dry
cycles and cancel the Set mode
NOTE: Two complete dry-to-dry cycles take approximately 9 minutes to
complete.
Clearing Drive Errors
If a temperature or development time is out of tolerance for at least 20 seconds,
an error condition is generated and the processor will enter the Stopped mode. No
new material will be accepted, however, material already in the processor will be
processed.
1. Correct the error condition.
2. Press Material to select the material screen.
3. Press the Up Arrow to select the processor setup screen.
4. Press Set to access the setup screen in the Set mode.
5. Press Material to operate the processor for one complete dry to dry cycle and
cancel the Set mode.
5-18
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Additional Troubleshooting Tips for the Processor
You can avoid many error conditions by following these guidelines:
•
•
Check that the processor is turned ON and warmed up prior to printing.
Follow the daily, weekly, monthly and periodic maintenance guidelines
outlined in Chapter 4.
•
When adding chemicals or water to the processor tanks, install a splash guard
over the entrance area of the processor to prevent water and chemicals from
entering the printer.
WARNING: When troubleshooting or performing maintenance
procedures that require the main power to be turned off, turn
off the main power for the processor on the OCP and at the
circuit breaker to prevent:
• injury from moving parts and high voltage electricity
• losing the processor parameters
•
Do not allow the emulsion side of the processed prints to touch each other
until they are completely dry.
Calibration Troubleshooting
This section describes the problems that you may occasionally have when using
the KODAK Device Calibration Software or the Calibration Software for the
KODAK PROFESSIONAL LED II Printer. It also identifies the probable causes for
these problems and provides solutions for correcting these problems.
Calibration Graph
The graph below is an indication that the calibration performed was out of
tolerance.
This may be result from invalid densitometer readings. It is necessary to perform
another calibration cycle if you see a graph that looks like the one above.
October 2002
5-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Calibration Error Codes
Error
Code
Error Code /Status
Possible Cause/Subsystem
Possible Solution
Message
1
2
3
The following file is
locked:_filename_.
The system is trying to access a
file that is currently in use.
Close any other applications that
may be accessing the file.
The following file is
protected:_filename_.
The system is trying to access a
file that is protected.
Change the protections on the file
to grant access to the user.
The following file was not
found:_filename_.
The system was trying to access
a file that it could not find.
Verify that the filename on one of
the configuration dialog windows is
correct.
4
Error:_oserror_occurred
during operation:_operation_
on file:_filename_.
An operating system error
occurred.
• Rerun the application.
• Reboot the operating system
5
6
7
The following file is in an
incorrect format:_filename_.
The file does not conform to the
application specification.
Verify the file format.
The following file already
exists:_filename_.
The system is trying to save to a
file that already exists.
• Delete the existing file.
• Change the filename.
There is not enough space to
create:_filename_.
The system is trying to save a file
but there is not enough disk
space.
Remove any unnecessary files to
increase free disk space.
8
9
There are too many files to
open _filename_.
Too many files open.
Close some files and or
applications.
You do not have permission
The file permission is invalid.
Rerun the application.
to open file _filename_.
10
Error copying print LUT to
DP2 folder (can’t open
_filename_.
Folder doesn’t exist or is read-
only.
Modify protection on folder.
11
Error creating DP2 LUT
folder
A folder of the same name may
exist.
Change the selected folder name.
101
102
No response from
device:_devicename_.
The device is not responding to
the system.
Verify that the device is connected
and on-line.
Device not
found:_devicename_.
The system was trying to access
a device that it could not find.
Verify that the device name on one
of the configuration dialog
windows is correct.
103
The following device is
indicating it is not
ready:_devicename_.
The device is not ready.
The device is busy.
Wait several minutes and try the
activity again.
104
105
The following device is
busy:_devicename_.
Wait several minutes and try the
activity again.
The following device is not a
TTY port:_devicename_.
The port name in the
configuration file does not refer to
a valid serial port.
Change the port name in the
configuration file to a valid serial
port.
5-20
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Error
Code
Error Code /Status
Message
Possible Cause/Subsystem
Possible Solution
106
107
108
The following device is
closed:_devicename_.
The serial port closed during
system reading.
• Verify that no other application
is accessing the port.
• Restart the application.
No data on
device:_devicename_.
No data is available for the
system to read data on the serial
port.
• Verify that the densitometer is
connected correctly.
• Restart the application.
Error:_oserror_occurred
during operation:
_operation_ on device:
_devicename_.
An operating system error
occurred.
• Rerun the application.
• Reboot the operating system
• If problem continues, call for
service.
109
110
Invalid Device ID:
_devicename_.
Created a new device with an
incorrect device ID.
• Edit the device ID to reflect the
correct device ID.
Unable to perform operation: An unknown device error
_operation_
Status Message:_statmsg_
Error Message:_errmsg_.
Use the information in the status
message and error message to
resolve the device error.
occurred.
111
112
113
114
There is insufficient memory
for the requested operation
on device:_devicename_.
The application does not have
enough memory to complete the
operation.
Close the other applications and
unnecessary windows.
A communications time-out
occurred during operation on
device:_devicename_.
The connection between the
printer and host computer was
lost.
Check that all of the cables are
properly connected.
A device driver for the
following device could not be
found:_devicename_.
The application could not find the
necessary device software to
communicate with the printer.
Make sure that the Calibration
Application and ASPI SCSI device
driver are installed correctly.
An error occurred during
communications to the
following device:
• The cable between the printer
and the host computer is worn.
• One or more of the
• Check that all of the cables are
properly connected.
• Check the cables and
_devicename_.
connections between the
printer and the host computer
has malfunctioned.
connections between the printer
and the host computer for wear
and if necessary, replace them.
115
An operation error occurred
during communications to
the following device:_
devicename_.
• The cable between the printer
and the host computer is worn.
• One or more of the
• Check that all of the cables are
properly connected.
• Check the cables and
connections between the
printer and the host computer
has malfunctioned.
connections between the printer
and the host computer for wear
and if necessary, replace them.
116
117
A software warning has been
issued by the following
device: _devicename_ Error
Message: _errmsg_
A software error has occurred on
the printer.
Resolve printer error condition.
Resolve printer error condition.
A software error has been
detected by the following
device: _devicename_ Error
Message: _errmsg_
An error has occurred on the
printer.
October 2002
5-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Error
Code
Error Code /Status
Message
Possible Cause/Subsystem
Possible Solution
118
119
120
A SCSI ID for the following
device was not found:
_devicename_.
SCSI driver not found.
Reinstall SCSI driver on host
computer.
The wrong SCSI ID was
specified for the following
device: _devicename_.
SCSI ID is incorrect.
Set Target SCSI ID to printer SCSI
ID.
This device has been setup
for the wrong model of
printer: _devicename_.
Device chosen has not been
found.
Verify device chosen matches the
printer model.
121
122
Unable to read STATUS from
device: _devicename_.
Unable to see the printer.
Check SCSI cable connections.
Select a 10-bit LUT file.
The selected LUT contains
data that exceeds the limits
of this printer.
Trying to send a 12-bit LUT to a
10-bit printer.
201
202
203
204
An error occurred while
trying to allocate memory.
The system is trying to allocate
memory, however, no memory is
available.
Close any unnecessary
applications.
The following parameter is
invalid:_parametername:
_parametervalue_.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
The function is not supported
by the class.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
This function has not been
implemented.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
205
301
Must enter the following
field:_field_.
The operator left a blank
configuration field.
Enter information in the blank
configuration field.
The following key was not
found _key_.
• An internal error occurred with
the software.
• One of the files was edited
manually and a key was
changed.
• Restart the application.
• Restore the key to its previous
value.
• If problem continues, call for
service.
302
The following grouper was
not found:_grouper_.
• An internal error occurred with
the software.
• One of the files was edited
manually and a grouper was
changed.
• Restart the application.
• Restore the grouper to its
previous value.
• If problem continues, call for
service.
303
501
The call depends on a
current grouper, but the
current grouper has not been
set.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
An error occurred while
applying the data.
5-22
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Error
Code
Error Code /Status
Message
Possible Cause/Subsystem
Possible Solution
601
A bad count was entered.
The expected count
was:_count_.
• A file was edited manually and
an incorrect number of rows
was entered.
• An internal software error
occurred.
• Manually enter the correct
number of rows in the file.
• If problem continues, call for
service.
602
701
An error occurred during the
calculation process.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
Patch _patch_, column
_column_, value _value_ is
beyond tolerance
A density patch was out of
tolerance.
Perform another calibration cycle.
_tolerance_ for aim _aim_.
702
703
704
801
802
803
804
805
806
807
Patch _patch_ has a spread
of _spread_ which is out of
range _range_.
The spread between colors for a
given density patch is out of
tolerance.
Perform another calibration cycle.
CalToleranceFile can only be
initialized once.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
CalToleranceFile::
initialize must be called first.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
Could not find row:_row_.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
Could not find
column:_column_.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
Could not find element -
column:_column_.
row:_row_.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
Row value was not set
before using.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
Column value was not set
before using.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
Error deleting row:_row_.
An internal error occurred with the
software.
• Restart the application.
• If problem continues, call for
service.
Element at row:_row_;
column:_col_
value:_val_ failed audit.
An input file had incorrectly
formatted data in it at the location
indicated.
• Verify that you are using the
correct file.
• Edit the file and correct the
format.
October 2002
5-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Error
Code
Error Code /Status
Message
Possible Cause/Subsystem
Possible Solution
910
Configuration file
field:_filename_is invalid.
Calibration will be cancelled.
The user manually edited a field
in a configuration file and entered
an incorrect value.
• Manually enter the correct
value.
• Reinstall the application.
• If problem continues, call for
service.
911
919
Error_errcode_occurred.
Processing stopped.
An internal error occurred with the
software.
Restart the application.
Error occurred preparing to
handle exit from Kodak
Calibration. Will not perform
cleanup at exit.
An internal error occurred with the
software.
Restart the application.
921
Unable to return the printer
to its original state. Fix
printer problem and re-
calibrate.
The application was trying to
cancel but received an error when
sending the original LUT back to
the printer.
Printer is in an unknown state.
Correct any printer problems and
restart the application.
922
923
There is already a printer
open. Please close the open
printer first.
User tried to open a printer when
the printer was already open.
Close the open printer.
An error occurred during the
loading of a printer. Please
check to make sure the file
chosen was of the correct
type and/or format.
An error occurred during the
loading of a printer.
Check that the file chosen was of
the correct format or type.
924
941
No printer loaded.
The operator has not yet opened
a printer.
Open a printer.
The height and width values
do not agree with the size of
the target file.
The specified size does not match
the file size.
Enter the correct file size.
942
Unable to configure
densitometer. Densitometer
configuration file may be
corrupt or lost.
The file CalDevDensGen2.cfg is
corrupt or lost.
Restart the application. If problem
continues, call for service.
1003
1004
1005
Unable to load default
configuration file:_filename_. deleted or renamed or moved.
The default configuration file was
Restore the file manually or
reinstall the software.
Unable to set values
in new configuration file.
An internal error occurred with the
software.
Restart the application.
Unable to save configuration
file:_filename_.
The system is trying to save a file
but there is not enough disk
space.
Remove any unnecessary files to
increase free disk space.
1006
1007
Configuration file field:_field_
is invalid.
The user manually edited a field
in a configuration file and entered
an incorrect value.
• Manually enter the correct
value.
• Reinstall the application.
Unable to remove
directory:_directory_.
User does not have update
authority on the directory.
Verify that the user has authority
on the directory.
5-24
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Error
Code
Error Code /Status
Message
Possible Cause/Subsystem
Possible Solution
1101
Density DMIN/DMAX points
are invalid.
Density points are invalid.
Reread density values on
densitometer or make a new
calibration print.
1102
Density data is not
monotonic increasing.
Density data is invalid.
Density data is invalid.
Density data is invalid.
Reread density values on
densitometer or make a new
calibration print.
1103
1104
1201
Exceeded maximum number
of allowable data errors.
Reread density values on
densitometer or make a new
calibration print.
Asymmetric Density
Groupings are invalid.
Reread density values on
densitometer or make a new
calibration print.
Unknown response from
densitometer.
The application received an
unknown response from the
densitometer during
Verify that the baud rate of the
densitometer matches the
applications configuration.
initialization.
1202
1203
Error:_error_from
densitometer.
Unexpected error was returned
from the densitometer.
Calibrate the densitometer. If the
problem continues, check the
manual for the densitometer.
Error: Number of patches
seen by densitometer is
incorrect.
Unable densities on densitometer. Try adjusting frame counts or
reread the density patches on the
densitometer.
1300
1301
Values have not been loaded Matrix file missing.
Create a new device.
Create a new device.
Data or Matrix files have not
yet been loaded
Matrix file missing.
1302
Data cannot be saved, must
first apply the matrix
Matrix file missing.
Create a new device.
October 2002
5-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Non-Numeric Error Messages
Error Message
Possible Cause/Subsystem
Possible Solution
An underrun error occurred during
communications to the following
device.
• The cable between the printer
and the host computer is worn.
• One or more of the connections
between the printer and the host
computer has malfunctioned.
• Check that all of the cables are
properly connected.
• Check the cables and
connections between the printer
and the host computer for wear
and if necessary, replace them.
An UNKNOWN error occurred
during communications to the
following device.
An unknown error occurred in the
application.
• Restart the calibration application.
• If the problem continues, make
sure you have the Calibration
Application and ASPI SCSI
device driver installed correctly.
Device not found.
The host computer attempted to
contact the printer at the specified
• Make sure that the printer is
turned on and is on-line.
SCSI ID but did not get a response. • Make sure the Calibration
Application and ASPI SCSI
device driver are installed
correctly.
Invalid Device ID.
The host computer attempted to
contact the printer at the specified
SCSI ID but did not get a response.
Make sure that the printer is turned
on and is on-line
The following device is busy.
The following device is closed.
The printer at the specified SCSI ID
is busy.
Check that all of the cables are
properly connected.
The connection between the printer
and host computer was lost.
Check that all of the cables are
properly connected.
5-26
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics and Troubleshooting
Getting Additional Help
Your Kodak Representative is the best source for information about the KODAK
PROFESSIONAL RP 50 LED Printer and Processor.
In addition, technical support is also available in the United States. Call Kodak’s
Technical Assistance Center at 1-800-822-1414 from 8:00 a.m. to 8:00 p.m.
Eastern Standard Time on regular business days.
Have your printer’s K-Number ready. The K-Number label is attached to the front
of the printer, next to the operator control panel.
Help numbers can be located on the web site at http://www.kodak.com/include/
international.shtml
October 2002
5-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Ordering Supplies
This appendix includes ordering information for Kodak accessories, supplies,
paper, chemicals and publications.
Accessories
Purchase these items through Kodak.
Catalog
Number
Item
Qty/Size
X-RITE DTP—36 Densitometer
10 - 20 Inch Paper Cassette
10/11 Inch Paper Cassette
1
1
1
1
1
1
1
1
196–1119
159–2971
164–0978
812–6153
839–0502
862–5667
*
Processor Print Catch Tray
Drip Tray /Liquid Measure Bottle Kit
Wash Water Conversion Kit—Model WPS-A
SCSI Interface Kit
Square-D Buck and Boost Transformer
(Model #500SV43F)
869-7799
* Order through your Kodak Sales Representative.
Supplies
Purchase these items from Kodak or through your dealer/distributor.
Catalog
Number
Item
Qty/Size
Printer Air Filter
Package of 10
833-3247
828–2170
KODAK EKTACOLOR RA-4 Control Strips
Box of 50
(31/2” X 12”)
Developer Filter
Package of 10
Package of 30
884–3781
137–7829
Bleach Fix/Stabilizer Filter
October 2002
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Supplies
Standard (U.S.) Paper
Purchase these items or the nearest equivalent through your Kodak
representative.
Surface
Types*
Item
Size
All KODAK PROFESSIONAL Papers
(Consult with your Kodak representative to
determine the best paper for your needs.)
E, F, or N
25.4 cm x 176M
25.4 cm x 88M
27.9 cm x 176M
27.9 cm x 88M
30.5 cm x 88M
50.8 cm x 88M
*Surface Types (availability depends on the paper type selected)
F = smooth, glossy
E = fine grained, lustre
N = smooth, semi-matt
Processor Chemicals
Purchase these items through your Kodak dealer or distributor.
Catalog
Number
Item
Qty/Size
KODAK EKTACOLOR RA Developer
Replenisher RT
10L/4 per case
841–5580
830–9031
122–4930
803–6832
857–5623
KODAK EKTACOLOR RA Bleach-Fix and
Replenisher/RA–4
10L/4 per case
6/48 ounce bottles
6/48 ounce bottles
10L/16 per case
KODAK EKTACOLOR RA Developer
Replenisher RT Additive
KODAK EKTACOLOR RA Bleach-Fix and
Replenisher/RA–4 Additive
KODAK EKTACOLOR PRIME Stabilizer
and Replenisher/RA–4
A-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Supplies
Publications
Call 1-800-431-7278 in the United States to purchase these items through Kodak
Parts Services.
Part Number/
Item
Qty/Size
Catalog
Number
Operator’s Guide for the:
KODAK PROFESSIONAL RP 50 LED
Printer
1
Part No. 2J0686
Quick Reference Guide for the:
KODAK PROFESSIONAL RP 50 LED
Printer
1
1
Part No. 2J0687
Using the KODAK EKTACOLOR RA
Chemicals
Part No. Z130
Cat No.160-5716
October 2002
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: Specifications
This appendix includes specifications and site requirements information for the
printer and processor.
Printer/Processor Specifications
Dimensions and Weight
Printer
Width
Length
Weight
102 cm (40 in.)
149 cm (58.5 in.)
420 kg (925 lbs)
438kg (965 lbs)–w/paper
Processor
Width
Length
Weight
87.6 cm (34.5 in.)
130 cm (51 in.)
190 kg (420 lbs)
198 cm (78 in.)–w/print rack
To move the printer through a 91 cm (36 in.) doorway, the following parts will be
removed by a Kodak representative:
•
•
•
•
front printer door
rear printer door
sheet transport module door
operator control panel
To move the printer through a 71.2 cm (28 in.) doorway, the following parts will be
removed by a Kodak representative (in addition to the above parts):
•
•
•
•
enclosures
covers
subassemblies for the paper supply module
knife and sheet transport module
Acoustic Specifications
NOTE: These specifications apply to the KODAK PROFESSIONAL RP 50 LED
Printer and Processor only.
Sound Pressure
Level (LA)
Sound Power
Level(LWA
Operator
Position
Instantaneous
Peak > 130 dB(C)
)
Standby
51.3dB(A)
55.7dB(A)
NA
66.1dB(A)
71.0dB(A)
Full System
Operating
None
October 2002
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Site Requirements
Operator and Service Access
When fully assembled the equipment requires a minimum of 91 cm
(36 in.) on each side to allow sufficient access for normal operator maintenance
and for service.
3.5 meters + .3 meters (138 in. + 12 in.)
_
_
2.2 meters + .3 meters (86 in. + 12 in.)
_
_
15A
30A
.91 meters (36 in.)
minimum
1.5 meters (60 in.)
2.9 meters
(114 in.)
*
Printer
.91 meters (36 in.)
minimum
Processor
.91 meters (36 in.)
minimum
.91 meters (36 in.)
minimum
4.5 meters (179 in.)
SCSI-2 connection from host here
*
Floor Requirements
The equipment should be installed on a smooth, hard, and level floor surface.
Carpet is not recommended.
The floor pitch should not exceed 1 inch in 5 feet.
B-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Plumbing
NOTE: Always adhere to local ordinances and regulations for wastewater disposal.
A plumbed processor with a water wash system is required for environments with
temperatures above 27o C (80o F).
Plumbed Processors – Water Supply
You are responsible to provide adequate water supply and drainage for the
processor before it is installed.
We recommend that you order a water supply panel for plumbed systems from
Kreonite Inc. The water supply panel must be installed by Kreonite. However, a
Kodak representative will install flexible supply line to the processor and an
electrical connection to the solenoid. The water supply panel should be wall-
mounted within 4.9 m (16 ft.) of the rear of the processor.
Installation, technical support and warranty of the water supply panel is the
responsibility of Kreonite.
Water to a plumbed system must meet the following specifications:
•
•
Flow Rate:
3.8 – 20.0 liters per minute (1 – 5 gallons per minute)
Temperature: Hot – 59o C (120o F) minimum
Cold – 27o C (80o F) maximum
Plumbed Processors – Waste Water and Effluents
A 2 inch floor drain should be located near the processor. The drain system
should conform to the local specifications for silver-laden bleach-fix and stabilizer
or waste water.
A Kodak representative will install a flexible drain tube to the processor. You are
responsible for installing the flexible drain tube to a locally approved drain system.
For unplumbed systems,10-litre containers are installed under the processor to
transport waste to the site’s waste facilities.
We recommend that you install a 61 cm (24 in.) wide sink near the processor for
cleanup and processor maintenance.
Unplumbed Processors
We recommend that you install a 61 cm (24 in.) wide sink near the processor for
cleanup and processor maintenance.
October 2002
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Electrical
The KODAK PROFESSIONAL RP 50 LED Printer and Processor are
manufactured to operate within one of the following sets of power constraints or
can be configured to do so by your Kodak representative:
Power
Consumption
Nominal Voltage/Frequency
Voltage Range
Printer: 200 - 240V, 15A, 50/60 Printer: 190 - 254V, 47 - Less than
Hz, 1 phase
63 Hz, 1phase, 15 A
(Automatic Sensing)
Processor: 208 - 254V,
47 - 63 Hz, 1phase,
30A**
9.12kVA
Processor: 230V, 30A, 50/60
Hz, 1phase or 3 phase
(selectable at installation)*
* Phase selection must be completed at the factory or by a trained Kodak
representative.
* *Outside the U.S. and Canada, amperage for the printer is 16A, and the
amperage for the processor is 32A.
NOTE: To prevent processor failures caused by power fluctuations, purchase a
Square-D Buck and Boost Transformer (Model #500SV43F) EK Catalog
#869-7799. Other transformers may not provide satisfactory results.
Consult with your electrical contractor or utility company to ensure that on-site
wiring complies with the printer specifications and that wall outlets use isolated
grounds and comply with codes. Further information is provided in the following
sections.
If the equipment is to be permanently connected, then the equipment must be
provided with its own circuit breaker that is located near the equipment within
easy reach of the operator and marked as the disconnecting device for the
equipment.
A protective earth ground must be supplied when installing the processor.
The unit is an Insulation Category Type II machine, and operates in a Pollution
Degree 2 environment in accordance with IEC 664 (Normal Office Environment).
For technical support, service, repair and fuse replacement information, contact
Eastman Kodak Company’s Technical Assistance Center at 1-800-822-1414.
B-4
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power Cords
A 2.4 m (8 ft.), grounded power cord with a special three prong plug is provided
with your printer. In addition, an 2.4 m (8 ft.), grounded power cord with a three
prong plug is provided with your processor. The printer conforms to the NEMA N6/
15 Printer Plug Specification. The processor conforms to the NEMA L14-30
Printer Plug Specification.
Special plugs and cords may be required outside of the United States and
Canada. These plugs and cords will be provided by the Kodak distributor (the
power cord provided for international locations must have at least 14 gauge wire
for the printer and 10 gauge wire for the processor).
The power cords should be certified and approved by a national test house.
For technical support, service, repair and fuse replacement information, contact
Eastman Kodak Company’s Technical Assistance Center at 1-800-822-1414.
CAUTION: Make certain nothing obstructs or is placed on power cords. Do
not use extension cords; they can cause voltage loss which may
result in unreliable equipment performance or equipment
damage.
Power Outlets
A separate, dedicated power line with a 208 V, 15 amp dedicated receptacle is
required for the printer.
A separate, dedicated power line with a 208 V AC, 30 amp dedicated receptacle is
required for the processor.
The outlets should meet the following standards.
Printer
Processor
amperage
wire size
phase
15 amp
30 amp
10 gauge or larger
3 or 1
14 gauge or larger
1 (single)
receptacle
NEMA5—N6/15
less than 2 ohms
NEMA6—30R
less than 2 ohms
impedance between
ground and neutral
wires
voltage drop across
the circuit breaker
less than 0.1 volts
less than 0.1 volts
distance between
receptacle and
equipment
1.5 m (5.0 ft.)
or less
1.5 m (5.0 ft.)
or less
October 2002
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Line Frequency
In most cases, the electric utility company is responsible for maintaining the
proper frequency of the alternating current in its distribution network. If the
building is supplied with power by its own motor-generator, make certain that the
governor that controls the frequency is capable of delivering power within the
required operating frequency range.
Power Receptacles (U.S. and Canada)
OB IG
OA OC IN
Computer system
branch circuit panel
20P/20R
#1
PRINTER
15A
NEMA Reference:
Receptacle 6-15R
Plug
6-15P
#2
30A
20P
PROCESSOR
NEMA Reference:
L6-30R
NEUTRAL BUS
(Isolated from power panel)
GROUND BUS
(Isolated from power panel)
B-6
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Printer Power Receptacles (Europe)
OB IG
OA OC IN
Computer system
branch circuit panel
CEE (7)
250,16A
L
N
16A
2
(1.5 mm )
OR
16A
L
N
Pin
CEE (7)
250,16A
NEUTRAL BUS
(Isolated from power panel)
GROUND BUS
(Isolated from power panel)
October 2002
B-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Processor Power Receptacles (Europe)
OB IG
OA OC IN
Computer system
branch circuit panel
ICE Connector 309
32A, 3 pin, 230VAC
32A
2
(4.0 mm )
OR
16A
16A
16A
NEUTRAL BUS
2
(4.0 mm )
ICE Connector 309
32A, 5 Pin, 230-400VAC
(Isolated from power panel)
GROUND BUS
(Isolated from power panel)
B-8
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Line Voltage
The printer and processor operate satisfactorily over a range of voltages around
the nominal voltage.
The local utility company is required to deliver power usually within ±10% of the
rated value to the main distribution panel in the building. Voltage then drops from
there to the outlets where the equipment is connected. The total voltage drop is a
function of the following factors:
•
The composition of the conductor material in the wire. Copper wire is a better
conductor than copper-clad aluminum and aluminum wire, which results in
less voltage loss over the same length of wire.
•
•
•
•
The diameter or gauge of the conductor. Large diameter conductor exhibits
less voltage loss than small diameter conductor.
The length of the circuit. A long circuit layout may result in more voltage loss
than a short, direct circuit layout.
The load or current on the circuit (amperes). A large circuit load may result in
voltage loss in a circuit.
The types and number of connections. Several connections in a circuit
increase the chance of improper wiring practices, which could result in
voltage loss.
You must allow for adequate wiring to keep the supplied voltage within the
required range. Otherwise, intermittent data errors and system errors may occur.
Low-voltage problems are more common than high-voltage problems and are
generally caused by poor wiring practices.
October 2002
B-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Operating Environment
If the environmental temperature changes more than 3o Celsius (5o Fahrenheit)
since the printer was last calibrated, calibration is necessary to maintain the
image quality of the prints.
The printer operates in typical office under the following conditions:
Lighting
(Maximum)
Temperature
Relative Humidity
Altitude
15o to 30oC
(59o to 86o F)*
15% to 76%
(40% to 55%
recommended)
0–2000 m
(0–6562 ft.)
325 lux* *
(30.2 ft.
candles)
*
Stabilizer wash: 27o C (80o F) maximum
Water wash: 30o C (86o F) maximum
A plumbed processor with a water wash system is required for environments
** Although the printer and processor operate in normal room lighting, access to
a darkroom is required to load the paper into the paper cassettes. Do not
operate the printer in areas with intense lighting.
NOTE: The operating environment should be free of smoke and excessive dust.
Venting the Processor
At least 10 complete air changes per hour are required for the room that the
processor is in. Whenever possible, vent the processor directly to the outside in
accordance with local, state and federal regulations.
NOTE: A 7.6 cm (3 in.) processor vent kit is available from Kreonite Inc. for rooms
that have less than 10 air changes per hour.
Air conditioning requirements:
The Printer generates 7,509 BTU/hr.
The Processor generates 18,020 BTU/hr.
B-10
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Processor Humidity Specifications
If the humidity is low (approximately 15 - 20%), check the chemistry levels in the
tank every 2 hours. Make sure that the chemistry in each processor tank is at the
top of the overflow pipe. If necessary, add water to reach the correct level.
overflow
pipe
IMPORTANT: Operate the processor’s main drive for approximately 15 to 30
minutes after topping off the tanks.
Wash Chemicals
Maximum Environmental Temperature
Wash Chemical
Stabilizer Wash
Water Wash
27o Celsius (80o Fahrenheit)
27o — 30oCelsius (80o— 86o Fahrenheit)
Telephone line
A telephone line (with a RJ11C modular phone jack) must be installed within
3 m (10 ft.) of the printer to support the remote diagnostics. We recommend a
high-grade analog service line.
Densitometer
An X-RITE DTP—36 Densitometer is required to calibrate the printer and for
process control. It is available through Kodak. See “Accessories” on page A-1.
October 2002
B-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
SCSI Cable
A single-ended or differential-ended SCSI cable is required to connect the host
computer to the printer. Install a single-ended SCSI cable if the distance between
the host computer and the printer is less than 6 meters. Use a differential-ended
SCSI cable if the distance between the host computer and the printer is greater
than 6 meters but less than 30 meters.
IMPORTANT: The printer is configured in single-ended mode at the factory.
Before installing a differential-ended SCSI cable, you must contact
your Kodak service representative to have your printer
reconfigured to the differential-ended mode.
B-12
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Additional Calibration
Information
The topics covered in this section include:
•
•
•
•
Installing the Calibration Software
An overview of the KODAK Device Calibration Software
Advanced Features of the RP 50 Calibration Software
Installing the Densitometer
IMPORTANT: For the step-by-step procedure to calibrating the printer, see
“Calibrating the Printer” on page 2-3.
Installing the Calibration Software
Installing the software includes installing both the Kodak Device Calibration
Software (which manages the calibration of multiple Kodak devices) and the
Calibration Software.
System Requirements
MACINTOSH Version
•
•
•
•
•
Power MACINTOSH System 7.5 or above
Minimum of 35 MB free disk space
608 K free disk space for each of as many as six configured devices
256 colors at 640 x 480 spatial resolution
CD ROM Drive
WINDOWS NT Version
•
•
•
•
100 MHz PENTIUM Processor
64 MB Main System Memory
VGA Monitor (640 x 480 spatial resolution)
CD ROM Drive
October 2002
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Installation Procedure
1. Place the supplied CD-ROM in your CD-ROM drive.
2. When the Browser appears, select LED Printer.
MACINTOSH Version
Under “Download File,” select LEDCalAppVn (n is the current version number).
LEDCalAppVn is saved to your desktop.
WINDOWS NT Version
Under “Download File,” select KPRO Calibration Utilities.
You can either save the installation file to a hard drive or run it directly from the
Internet.
If you choose to save the installation file to a hard drive, the Save File dialog box
appears. Either accept the path and file name or select another path and file name
and save the file.
MACINTOSH Version and WINDOWS NT Version
NOTE: From this point on, the installation is similar for Macintosh and Windows
NT systems. When the instructions say, for example, click Next or Install,
the first option is for Windows NT systems; the second is for Macintosh
systems.
CAUTION: Toavoidpossible damage, do not connect ordisconnect thecable
between your host computer and the printer when either device
is powered up.
1. Double-click the installation file.
The splash screen for KODAK PROFESSIONAL Universal Calibration Utility
appears and a Setup message appears.
2. After the Welcome screen appears, click Next or Continue.
3. For Macintosh systems only, read the readme information, then click
Continue.
4. Read the license agreement.
•
•
To accept the terms and continue the installation, click Yes or Agree.
Or, to cancel the installation, click No or Disagree.
5. For Windows NT systems only, read the readme information, then click Next.
C-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
6. Select the installation type:
For Windows NT systems, select one of the following:
•
Typical
includes Device Calibration Applications for the Kodak
Professional LED Printer and for the Kodak Professional
Digital Multiprinter, plus the Linearization Calibration
Application for the Kodak Professional RFS 3570+ (Speed
Up) Film Scanner
•
•
Compact allows you to choose to install individual applications from the
list included under Typical
Custom
allows you to choose specific features for the application you
choose to install; for the LED Printer, you may choose to
install either Gen I or Gen II
For Macintosh systems, select Easy Install.
7. Click Next to install the software on your system.
A dialog box appears for you to designate where to install the calibration
software.
8. Either accept the default path and folder or select another path and folder.
9. Click Finish or OK.
NOTE: For Windows NT systems, the screen gives you the option of reading
the readme file associated with your installed applications.
10. Remove the CD-ROM and store it in a safe place.
October 2002
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Kodak Device Calibration Software
The Kodak Device Calibration Software is used to launch the Calibration Software
for the printers and scanners.
NOTE: Most of the windows displayed in this chapter are from the WINDOWS NT
Version of the software. The windows for MACINTOSH Computers are
similar.
Application Window Definitions
The window below and the tables that follow define the application window for the
KODAK Calibration Device Software.
Title bar
Tool bar
Menu bar
Device icon
(this appears
when you add
a calibration
device)
Client area
Status bar
Window Area
Description
Title Bar
Menu Bar
Tool Bar
Contains the application name, “KODAK Device Calibration”
Contains selectable menu items
Contains the user selectable menu choices and is activated by a shortcut keystroke
or by a mouse pointer and left mouse button
Client Area
Device Icon
Status Bar
Contains the icons that represent devices available for calibration
Represents a device that can be calibrated
Displays messages to the user to indicate actions that are occurring or the status of
the occurring action and the currently selected device
C-4
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
The table below defines the functions and their corresponding icons on the main
window of the KODAK Device CalibrationSoftware.
Menu
Access
Function
Icon/Key
Availability
Description
Operations Calibrate
When the
device is
selected
Passes control to the
calibration software for the
device; double-clicking on a
device icon performs the
same action
MACINTOSH:
+L
WINDOWS NT: Ctrl+L
File
New
Always
Displays a Create a New
Device dialog box; adds a
device to the control area
MACINTOSH:
+N
WINDOWS NT: Ctrl+N
Edit
Cut
When a
Removes the object from
the control area. All history
data files (including log
data, LUT files etc.) will be
deleted for this device. A
confirmation dialog box
appears to allow you to
cancel the action.
calibration
device is
selected
MACINTOSH:
+X
WINDOWS NT: Ctrl+X
File
Edit
Always
If no object is selected, the
Edit Application
Configuration dialog box
appears. If an object is
selected, the Update a
Device Registry dialog box
for that device appears.
MACINTOSH:
WINDOWS NT: Ctrl+E
+E
MACINTOSH:
+Q
MACINTOSH:
Quit
File
Always
Always
Exits the application
WINDOWS NT: Ctrl+Q
WINDOWS NT:
Exit
Help
Product
Information
NA
Displays the Product
Information dialog box
October 2002
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Starting the Kodak Device Calibration Software
Load the Calibration Software according to the table below. (If needed, see
MACINTOSH Version
WINDOWS NT Version
1. Open the folder that
contains the files for the
calibration application.
Select:
Programs/Eastman Kodak/
KPRO Applications/
Kodak Universal Calibration Utility
from the WINDOWS NT Start menu.
2. Click on the icon for KODAK
Device Calibration.
Adding a Device
To add a calibration device icon to the KODAK Device Calibration Software:
1. Select New from the File menu on the KODAK Device Calibration window.
File menu
C-6
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
The Create a New Device dialog box appears.
2. Enter the correct device settings. Use a unique identifying word for the device
name.
NOTES: The default SCSI ID for the printer is 5. The printer’s OCP menu
displays the current SCSI ID for the printer.
Make sure the Device Type field matches the type of printer that
is being calibrated.
1. Click OK to accept the changes.
A new printer device icon appears on the KODAK Device Calibration screen.
NOTE: If an error message appears, refer to “Calibration Troubleshooting” on
page 5-19.
October 2002
C-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Editing the Log Settings
To change the log settings for the KODAK Device Calibration:
1. Deselect all devices on the KODAK Device Calibration screen and click the
Edit icon.
Edit icon
All devices
must be
deselected
The Edit Configuration dialog box appears:
2. Edit the device settings as needed or click Default to refresh the screen with
the default settings.
The log operations/settings include:
Device Setting
Options
Log Type
None: No logging of events or errors
Events: Log events only (status messages that appear on the screen)
Errors: Log errors only
Log all actions: Log all actions
Keep log for
(days)
Enter the number of days you want to keep logged information – for up to
99 days
Log File Name
Enter the name that you want to give to the log file
3. Click OK to save (or Cancel to cancel) the changes.
C-8
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Updating a Device
To update or change the device name or the SCSI ID for any device:
1. Select the device by clicking once on the device icon on the KODAK Device
Calibration screen.
Edit
icon
Device
icon
2. Click the Edit icon.
The Update a Device dialog box appears.
3. Enter the correct device settings.
The options for the device settings include:
Device Setting
Options
Device name
Enter the name that you want to give to the device.
NOTE: The MACINTOSH platform limits the device
name to 10 characters.
SCSI Host Adapter Adapter ID on host computer
SCSI ID The SCSI ID for the device
4. Click OK to save (or Cancel to cancel) the changes.
October 2002
C-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Deleting a Device
To delete a device from the KODAK Device Calibration Software screen:
1. Select the device by clicking on the device icon.
Cut icon
Device
icon
2. Click the Cut icon.
The following dialog box appears:
3. Click Yes to delete the files and directories for the selected calibration device.
(Click No to stop the deletion process.)
C-10
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Advanced Features to the Calibration Software
The Calibration Software provides automated neutral density printer calibration
and is designed to be used without assistance from technical experts. The
advanced calibration features provided by this product enable you to customize
the calibration of the printer. To use the advanced features, you should
understand image science technology and the implications of manipulating
neutral density calibrations.
IMPORTANT: Printer calibration should not be mistaken for color management.
Color management is provided by software applications that are
independent of the printer and the calibration software.
Viewing Graphs
The View Graphs feature provides access to the available graphs from the most
recently completed calibration.
Examples of the Value, Difference, and History Graphs are shown below. The
Value and Difference Graphs reflect the densitometer values that were last read.
The History Graph displays the data from completed calibrations.
October 2002
C-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Value Graph
C-12
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Difference Graph
October 2002
C-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
History Graph
To view calibration graphs:
1. From the KODAK Device Calibration screen, double-click the device for which
you want to view graphs.
C-14
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
The LED Calibration Application screen appears.
Graphs icon
2. Click the Graphs icon.
One of the graphs appears; normally it is the Value graph.
3. Select the Graph Type that you want to view. When the graph appears, select
the type of data and planes that you want to see displayed.
NOTE: The graph will be blank if the printer has not been calibrated.
Sending LUTs
The Send LUT to Printer feature allows you to overwrite the current LUT in the
printer. You can create a valid printing LUT using an ASCII text editor. This option
sends the selected LUT to the printer, overwriting any existing LUT.
To send a LUT to the Printer:
1. From the KODAK Device Calibration screen, double-click the device for which
you want to send a LUT.
October 2002
C-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
The LED Calibration Application screen appears.
Send
LUT icon
2. Click the Send LUT icon.
The Send LUT to Printer dialog box appears.
3. Select one of the LUTs from the dialog box and click Load Selected LUT or
click Load Custom LUT and follow the prompts to load a custom LUT. The
LUT is downloaded to the printer, overwriting the current LUT.
C-16
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Sending Targets
The Send Target feature enables you to send any properly formatted target file to
the printer without performing a calibration. The target file must contain image
data in the format for the printer. The format of this file must be raw RGB pixel
interleaved.
To send a test target to the printer:
1. From the KODAK Device Calibration screen, double-click the device for which
you want to send a test target.
The LED Calibration Application screen appears.
Send Test
Target icon
2. Click the Send Test Target icon.
October 2002
C-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
The Send Target to Printer dialog box appears. (Both the Windows NT and
Macintosh versions are shown here.)
WINDOWS NT Version
NOTE: Windows NT users can click Browse to select another file name. The
Open dialog box appears. Select the file name you want, then click
Open.
C-18
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
MACINTOSH Version
3. Enter the desired settings and click OK to save the settings (or Cancel to
keep the previous settings).
The selected test target is sent to the printer.
Editing the Calibration Configuration
The Edit Configuration feature allows you to change the printer’s calibration
configuration attributes. However, it is recommended that you use the default
settings for these attributes for most operations. The settings should only be
changed for the most advanced operations.
Edit Configuration consists of a set of six tabbed screens—each with related
configuration attributes. There can be only one set of configuration attributes for
the printer calibration application at a time. If you make any changes to one or
more of the tabbed screens and then click OK to save your changes, the changes
will overwrite the previous attributes used for the automated calibration.
To edit the calibration configuration:
1. From the KODAK Device Calibration screen, double-click the device for which
you want to change the calibration configuration.
October 2002
C-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
The LED Calibration Application screen appears.
Edit icon
2. Click the Edit icon.
The Edit Configuration screen appears with the Procedure tab displayed.
Edit Configuration Screen for WINDOWS NT Systems
C-20
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Edit Configuration Screen for MACINTOSH Systems
3. To navigate among the tabs, click the tab you want and follow the instructions
for updating the information for that tab.
IMPORTANT:Whenever you click OK, the software assumes ALL changes to
the Edit Configuration are complete and the Edit Configuration
screen closes. Similarly, you can click Cancel at any time while
the Edit Configuration screen is open; any changes you made to
any of the tabbed information are canceled and the Edit
Configuration screen closes.
Note that for Macintosh users only, you can click Default at any time to reset the
attributes to their factory defaults and then click OK to save the defaults.
October 2002
C-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Editing Information on the Procedure Tab
The Procedure tab contains general configuration attributes as shown and
described below. The values displayed in the example are the default settings.
Procedure
Attribute
Description
Graphing
Instructs the application when to display the graphs of the data
Indicates whether the level of tolerance is Normal, Loose, or Strict
Tolerance Level
Out of Tolerance
Provides the flexibility to interact at each step or to use a fully
automated calibration
Maximum Cycles
Indicates the maximum number of iterations the calibration
procedure will perform if “Out of Tolerance” is set to “Automatically
iterate up to maximum cycles.”.
Processor In Control Indicates whether the Processor In Control dialog box is to be
displayed at the beginning of the calibration process
C-22
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
To edit the configuration information on the Procedure tab:
1. Use the drop-down lists to change the Procedure information as needed.
2. If you have completed all editing of configuration information (including
information on the other tabbed screens), click OK to save the changes and
close the Edit Configuration screen.
NOTE:ClickCanceltocancelallchangesmadetotheEditConfigurationscreen
and close the Edit Configuration screen.
3. To continue making changes to the Edit Configuration, click on another tab
and make changes as needed.
October 2002
C-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Editing Information on the Density Source Tab
The Density Source tab specifies how the calibration application is to receive
density data. The values displayed in the example are the default settings.
Density Source
Description
Attribute
Density Source
Indicates the source (densitometer or file) of the density data.
Density Source Port
Indicates the name of the RS-232 port that the densitometer is
connected to. This port is the source of the density data. The name of the
port is specific to the computer system platform.
Density Source File
Indicates the filename for the source of density data. This is only used if
the Density Source is a file. If you designate a file as the density source,
this is the file name you use for “Creating a Density File for Use with
To edit the configuration information on the Density Source tab:
1. Use the drop-down lists to change the Density Source information as needed.
2. If you have completed all editing of configuration information (including
information on the other tabbed screens), click OK to save the changes and
close the Edit Configuration screen.
NOTE:ClickCanceltocancelallchangesmadetotheEditConfigurationscreen
and close the Edit Configuration screen.
3. To continue making changes to the Edit Configuration, click on another tab
and make changes as needed.
C-24
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Editing Information on the Aim Tab
The Aim tab specifies:
•
whether the aims used for calibration are to be Density Aims or Lightness
Aims
•
•
whether to apply the Channel-Independent Matrix
which table to use if Copyright Detection is functional
The values displayed in the example are the default settings.
Attribute
Description
Desired Aim
Indicates whether to use Density Aims or Lightness Aims for
calibration. Using Lightness Aims will improve both the highlights and
shadows of your prints.
Apply Channel
Independent
Matrix?
Indicates whether or not to apply the Channel-Independent Matrix to
the aim values. If the matrix is applied, the number of cycles required
to successfully calibrate the printer should be reduced.
Copyright
Select the table to be used. This feature is available with Gen II LED
Detection Table
printers only. Only use this feature as instructed by Kodak.
To edit the configuration information on the Aim tab:
1. Change the Aim information as needed.
2. If you have completed all editing of configuration information (including
information on the other tabbed screens), click OK to save the changes and
close the Edit Configuration screen.
NOTE: Click Cancel to cancel all changes made to the Edit Configuration
screen and close the Edit Configuration screen.
3. To continue making changes to the Edit Configuration, click on another tab
and make changes as needed.
October 2002
C-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Editing Information on the History Tab
The History tab specifies information about maintaining calibration history data.
The values displayed in the example are the default settings.
Attribute
Description
Keep History For (days) Indicates the number of days that the calibration LUT, print LUT,
density data and LUT history information (LED trend data) are to
be kept. Information older than the specified number of days will be
deleted.
Log Type
Indicates the type of log file available during calibration. All
recordable events or just the recordable errors can be logged to a
selected filename.
Keep log for (days)
Log File Name
Indicates the number of days that the error and events information
is to be kept. Information older than the specified number of days
will be deleted.
The name of the file that contains the logged information.
To edit the configuration information on the History tab:
1. Change the History information as needed.
2. If you have completed all editing of configuration information (including
information on the other tabbed screens), click OK to save the changes and
close the Edit Configuration screen.
NOTE: Click Cancel to cancel all changes made to the Edit Configuration
screen and close the Edit Configuration screen.
3. To continue making changes to the Edit Configuration, click on another tab
and make changes as needed.
C-26
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Editing Information on the Paper Tab
The Paper tab allows you to specify the paper being calibrated. The value
displayed in the example is the default setting.
Attribute
Paper Type
Description
Select either KODAK PROFESSIONAL Digital III Paper (Digital III) or
KODAK PROFESSIONAL Digital PT 2976 Paper (2976).
To edit the configuration information on the Paper tab:
1. Change the Paper Type if needed.
2. If you have completed all editing of configuration information (including
information on the other tabbed screens), click OK to save the changes and
close the Edit Configuration screen.
NOTE: Click Cancel to cancel all changes made to the Edit Configuration
screen and close the Edit Configuration screen.
3. To continue making changes to the Edit Configuration, click on another tab
and make changes as needed.
Editing Information on the DP2 (Windows NT) or KPIS
(Macintosh) Tab
The DP2 (or for Macintosh versions, KPIS) tab specifies whether to activate DP2
(or KPIS) interoperability, and if so, names the directory and filename designated
for the DP2 (or KPIS) information.
There are some minor differences in the editing of DP2 and KPIS information;
October 2002
C-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Editing DP2 Information (WINDOWS NT Systems)
When you click the DP2 tab of the Edit Configuration screen, the following tabbed
screen appears. The values displayed in the example are the default settings.
Attribute
Activate DP2
Description
Indicates if the calibration procedure should generate a LUT file to be
used with the DP2 system
DP2 Location
DP2 Filename
Directory to contain generated LUT files for use with DP2
Name of the file containing the DP2 LUT files
1. If DP2 is not already activated, click the Activate DP2 checkbox (click again
to deactivate) so that the screen looks like the example above.
2. To change the DP2 Location, type a new directory name or click Browse and
select another directory.
3. If needed, change the DP2 Filename.
4. If you have completed all editing of configuration information (including
information on the other tabbed screens), click OK to save the changes and
close the Edit Configuration screen.
NOTE: Click Cancel to cancel all changes made to the Edit Configuration
screen and close the Edit Configuration screen.
5. To make other changes to the Edit Configuration, click on another tab and
make changes as needed.
C-28
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Editing KPIS Information (Macintosh Systems)
If you are using the calibration output files with the KPIS system, it is necessary to
activate KPIS and assign a filename and location to the output file.
When you click the KPIS tab of the Edit Configuration screen, the following tabbed
screen appears. The values displayed in the example are the default settings.
Attribute
Description
Indicates if the calibration procedure should generate a LUT file to be used with
the KPIS system
Activate KPIS
KPIS Location
KPIS Filename
Directory to contain generated LUT files for use with KPIS
Name of the file containing the KPIS LUT files
1. Click the Activate KPIS checkbox (click again to deactivate).
October 2002
C-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
The display shows the Edit Configuration screen with the default settings for
KPIS Location and KPIS Filename.
2. To change the directory for the KPIS file:
a. Click KPIS Location. The display shows the Select KPIS Folder dialog
box.
b. If needed, browse to find the folder you want.
c. Click on Select “directoryname” (the example above shows Select
“KodakLED”).
C-30
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
The display shows the updated Edit Configuration screen with updated
File Location of CalDisk:CompositeMachine:Tables:KodakLED.
Completing the Edit Configuration
When finished, click OK to save the attributes. (Click Cancel to exit the screen
without saving your changes. Macintosh users: you can click Default at any time
to reset the attributes to their factory defaults and then click OK to save the
defaults.)
October 2002
C-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Creating a Density File for Use with Calibration
During calibration, you have the option of obtaining density data from a file or by
scanning a processed test target through an X-RITE DTP 36 densitometer. The
option is determined by the entry in the calibration configuration file. If the
configuration file is set up to receive density data from a file and you are creating
the file:
1. Scan the print into your densitometer.
function.
3. Move the density data file that you just saved to the folder or path selected on
the Density Source tab of the Edit Configuration screen (see “Editing
File Formats
NOTE: If a file contains data in a tabular format, each entry may be separated by
multiple spacesand tabs;however, when the fileissaved bythe application,
each group of multiple spaces and tabs is automatically converted to a
single tab.
DensityDataRaw (TECHNET Format)
Example:
R2340 G1000 B2010
R2350 G1010 B2020
R2360 G1020 B2030
R2370 G1030 B2040
C-32
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Calibration Information
Installing the Densitometer
This section describes how to install the X-RITE DTP 36 Densitometer, including
changing some of the attributes on the Edit Configuration screen to accommodate
the densitometer.
IMPORTANT: The supported densitometers use a RS-232 interface for
communication to the host. Each platform uses different
designations to identify the RS-232 ports.
To install the densitometer:
1. Connect the appropriate cable (provided by the user, supplier or with the
densitometer) between the densitometer and the host computer.
NOTE:For the X-RITE DTP 36 Densitometer:
•
•
Remove the protective strip (for shipping) from the densitometer.
Verify that the densitometer is configured with the factory defaults. (Refer
to the densitometer manual for this information.)
•
Perform an initial calibration of the densitometer. (Refer to the
densitometer manual.)
2. Run the calibration software for the printer and click the Edit icon to access
the Edit Configuration screen; see “Editing the Calibration Configuration”
3. Click the Density Source tab.
4. Edit the attribute for the Density Source. Select the appropriate choice for
your densitometer from the list.
5. Edit the attribute for the Density Source Port. Enter the name of the port that
the RS-232 cable is connected to on the host computer system.
Host System
Default Port
MACINTOSH
WINDOWS NT
Printer
COM 1
6. Click OK to save the changes to the configuration.
IMPORTANT:Densitometers require calibration at regular intervals. Refer to
your densitometer manualorinstructionson how to calibrate your
densitometer and perform a calibration.
October 2002
C-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Using the Image Print
Server Software
This section describes how to use the KODAK PROFESSIONAL Image Print
Server Software for WINDOWS NT Workstation 4.0 Systems.
The IPS Software enables printing of TIFF images and provides easy, intuitive
methods for performing simple print management operations that include:
•
•
•
•
stopping/suspending and resuming the processing
deleting images from the queue
inserting new images into the queue
applying a tone scale correction to images
In addition, IPS Software allows you to monitor a specified file system or folder
while waiting for TIFF images.
Communication Channels
Your computer can print to the RP 50 or 20R Printer through a SCSI connection
only.
Installing the IPS Software
You must be familiar with the WINDOWS System in order to perform the
installation.
Hardware Requirements
The following is the minimum hardware required for the IPS Software:
•
•
•
64 MB Main System Memory
100 MHz PENTIUM Processor
VGA Monitor (640 x 480 spatial resolution)
Software Requirements
The following must be installed on your computer:
•
•
WINDOWS NT Workstation 4.0
An ASPI-compliant SCSI interface driver
October 2002
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Image Print Server Software
Installing the Software
1. Insert the IPS Software CD into the CD-ROM drive.
2. Double-click on the Setup.exe icon.
3. Follow the on-line instructions to complete the installation.
The default installation location for the software is “C:\Eastman Kodak\KPro
Applications\KODAK PROFESSIONAL Image Print Server.” In addition to the
application, the installation procedure also installs a tone scale correction LUT
that may be used by the IPS application. The default installation location for this
LUT is “C:\Eastman Kodak\KPro Color Management\LUTS.”
Using the Image Print Server
This section summarizes the process of printing an image. See “Dialog Boxes and
Print Options” on page D-6 for detailed descriptions of the options.
Inserting Images into the Print Queue
The IPS application allows you to submit images by specifying a “hot folder” (for
example: the Source Directory in the Source Directory Preferences dialog box)
or inserting through the enqueue function from the application menu bar.
Source Directory Insertion
Images placed in the Source Directory are automatically placed into the print
queue. The images are then sorted by the date and time that they were placed in
the Source Directory. Images are printed in the order that they are placed into
the directory. Once the image has been downloaded, the file is removed from the
Source Directory.
NOTE: The properties of the images that are placed in the Source Directory are
taken from the Source Directory Preferences dialog box.
Menu Bar Insertion
To enqueue an image through the menu bar, select File->Enqueue or click the
Enqueue button.
Images placed in the queue through the menu bar are not removed from their
original directory after they are downloaded.
NOTE: The properties of images inserted in this manner are taken from the
Enqueue dialog box.
D-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Image Print Server Software
Suspending and Resuming
When the IPS application begins execution, it searches the current directory for its
preferences file, KIPSpref.dat. If this file is not found, the application begins
execution in the “suspended” state as if the Suspend button was pressed. While
suspended, the application does not communicate with the printer for any reason.
As a result, the status bars on the application will not reflect the accurate state of
the printer.
If the application is suspended, pressing the Resume button will activate the
application. If the preferences have not been initialized (for example: first time
execution), you are prompted to initialize the IPS preferences. The application will
remain suspended until the preferences have been properly initialized.
If the preferences file is found when the application is launched, the application
will begin execution in the “running” state as if the Resume button was pressed.
Failed Jobs
When an image fails to download for any reason, an appropriate error message is
appended to the log. The log file is specified in the Source Directory Preferences
dialog box.
Images in the Source Directory are moved to the FailedJobs Directory. The
FailedJobs Directory is created as a subdirectory within the Source Directory
when the first failure occurs.
Images that fail and were not inserted through the Source Directory are not
moved to the FailedJobs Directory.
Attended Operation
The IPS application allows you to operate in the Attended or Unattended mode.
The Server-> Attended menu item is used to enable and disable Attended mode
operation.
In Attended mode, all errors are displayed in dialog boxes. The IPS application is
halted until you respond to the message.
In Unattended mode, only errors that require user intervention are displayed in
dialog boxes. Errors that do not require user intervention, such as an invalid file
format, are logged in the log file.
In both Attended and Unattended modes, all errors are written to the log file.
NOTE: If a communication error occurs while the file is being downloaded to the
printer, the image may not be printed. In addition, jobs that fail to print from
the source directory are copied to the failed jobs directory.
October 2002
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Image Print Server Software
The Enqueue dialog box appears.
2. Type a file name into the Image File text box or click the Browse button.
3. Click OK to close the Enqueue dialog box and to insert the specified file into
the print queue.
NOTE: You cannot enqueue a file that is being downloaded to the printer. You
must wait the file has completed downloading before you can access
the file.
October 2002
D-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Image Print Server Software
Dialog Boxes and Print Options
This section describes the dialog boxes and print options for the KODAK Image
Print Server Software.
KODAK PROFESSIONAL Image Print Server Main Window:
D-6
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Image Print Server Software
Option Descriptions
The main window allows you to choose the following options:
Menu Access
Button
Enqueue
Icon
Description/Function
File
Displays the Enqueue dialog box and allows
you to insert a new image into the print
queue.
File
Dequeue
Flush
Allows you to remove the top entry from the
print queue.
File
Allows you to delete all entries from the print
queue.
Server
Server
Help
Suspend
Resume
About
Suspends the operation of the application. If
an image is being sent to the printer, it will
continue to download and is active only
when the system is executing normally.
Resumes the operation of the application
and is active only when the system is
suspended and can only be used if the
server defaults were initialized.
Displays the About box that includes version
information about the IPS.
October 2002
D-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Image Print Server Software
Enqueue Dialog Box
Option Descriptions
The selections/options that you can make from the Enqueue dialog box include
the following:
Image File Text Box— you may type in a name or browse the directory structure.
OK—closes the dialog box and inserts the specified file into the print queue.
Cancel—closes the dialog box without saving any changes.
Copies—the number of copies to print. The valid number of copies is 1—9999
Printer Resolution—“125 ppi” enables the hardware pixel replication capability
on the printer, “250 ppi” prints the image pixel for pixel.
Print Production—“Immediate” instructs the printer to print the image
immediately, “Deferred” allows the printer to buffer the image until an entire sheet
of images can be printed.
Punches—“Order Punch” places a punch between each order, “ID Punch” places
a punch .25 in. inside each image area to mark a gutter for host image
information.
Tone Scale Correction—”Correction File” is the name of the file to use for the
tone scale correction. A 2.2 gamma correction LUT is installed with the
location. Select the “Apply” box to instruct the application to apply the LUT to the
image.
D-8
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Image Print Server Software
Source Directory Preferences Dialog Box
Option Descriptions
The selections/options that you can make from the Server Default dialog box are:
OK—closes the dialog box and saves the specified values.
Cancel—closes the dialog box without saving any changes.
Source Directory—the directory/folder where the TIFF application will look for
the TIFF images to arrive. Type a directory name or click the browse button.
Log File—the file name where the IPS application will store the printer error
information. Type a file name or click the Browse button.
Copies—the number of copies to print. The valid number of copies is 1–9999
Center Image—centers the image on the paper.
Printer Resolution—“125 ppi” enables the hardware pixel replication capability
on the printer, “250 ppi” prints the image pixel for pixel.
Print Production—“Immediate” instructs the printer to print the image
immediately, “Deferred” allows the printer to buffer the image until an entire sheet
of images can be printed.
Punches—”Order Punch” places a punch between each order. “ID Punch” places
a punch .25 in. inside each area to mark a gutter for the host image information.
Tone Scale Correction—”Correction File” is the name of the file to use for the
tone scale correction. A 2.2 gamma correction LUT is installed with the
location. Select “Apply” to instruct the application to apply the LUT to the image.
October 2002
D-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Image Print Server Software
Initialize Default Parameters Dialog Box
Description
This dialog box appears if you press the Resume button (or activated through the
menu bar) before the Source Directory Preferences have been initialized.
File Format Details
The data portion of the TIFF file must contain RGB byte interleaved data. The
specific TIFF tags that are supported are shown below.
Supported Tags
The Image Print Server supports the TIFF tags listed below. The range of legal
values for TIFF tags 256, 257, 258, 273, 278 and 279 are image dependent. If
these values are incorrect, an error will occur while reading the image data and an
appropriate error message will be placed in the log file. Values indicated in the
table below by a “*” are image dependent.
TIFF Tag ID
Name
Valid Range
256
Image Width
*
*
257
258
Image Length
Bits per Sample
*
2
*
3
*
262
273
Photometric Interpretation
Strip Offset
277
278
Samples per Pixel
Rows per Strip
279
284
Strip Byte Count
*
1
Planar Configuration
*indicates an image dependent value.
LZW Compression
The IPS does not support LZW compression.
D-10
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: Using the PHOTOSHOP
Export Module
This appendix describes how to use the Export Module for PHOTOSHOP on
MACINTOSH Systems with the KODAK PROFESSIONAL RP 50 LED Printer.
The Export Module allows you to export prints from PHOTOSHOP to a KODAK
PROFESSIONAL 20P Printer.
The Export Module allows you to:
•
•
Scale an image by 200%
Center an image within a user specified border
Installing the Export Module
This section explains how to install the Export Module on your MACINTOSH
system. It assumes that you are familiar with the MACINTOSH System
Environment.
Hardware Requirements
The following hardware is required for the Export Module:
•
•
•
•
120 MHz PowerPC 601 Processor
Minimum of 72 MB of RAM
Hard disk space that is at least three times your image size
A standard SCSI terminator if you are daisy-chaining your external disk drive
or other peripheral with the printer and you are not using a MACINTOSH IIfx
Computer
•
•
An APPLE SCSI Terminator if you are using a MACINTOSH IIfx Computer
and you have an external SCSI disk drive or other
peripheral device
KODAK PROFESSIONAL Printer
Software Requirements
The following must be installed on your MACINTOSH System:
•
•
MACINTOSH System 7.5.5 or later
ADOBE PHOTOSHOP, version 3.0 or later
October 2002
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PHOTOSHOP Export Module
Installing the Software
1. Open the Adobe Photoshop folder on your computer.
The Adobe Photoshop window appears. It should look similar to the one
shown below.
2. Insert the Host Software CD (included with your printer) into the CD drive.
3. Double-click the CD icon on your desktop.
4. Double-click on the Macintosh folder.
5. Double-click the KODAK LED Printer Export Module folder.
The KODAK LED Printer icons appear.
E-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PHOTOSHOP Export Module
6. Click and drag the KODAK LED Printer plug-in icon and Media Files over the
Adobe Photoshop Plug-ins folder and release the mouse button.
A copy progress dialog box appears as the folders and files are copied.
7. Click and drag the remaining files from the KODAK LED Printer window to a
Utility folder or another location on your system.
Printing Images
Do the following to print an image. See “Dialog Boxes and Print Options” on page
E-6 for details.
1. Start PHOTOSHOP and open an image file.
NOTE: Make sure the image is in the RGB Color mode. If the image is not in
the RGB Color mode when you try printing the file, you will receive an
error message.
2. Choose Export from the File menu.
NOTE: You cannot access the Export submenu if an image is not open in
PHOTOSHOP.
3. Choose KODAK LED Printer from the Export menu.
The KODAK LED Printer main dialog box appears.
4. Click Print.
October 2002
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PHOTOSHOP Export Module
To select another printer:
1. Click Select.
The Select a KODAK LED Printer dialog box appears.
2. Select the printer by clicking the appropriate button.
3. Click OK.
E-4
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PHOTOSHOP Export Module
The KODAK LED Printer main dialog box appears.
4. Make the remaining print option choices to meet the needs of your print job
from the KODAK LED Printer dialog box. See “Dialog Boxes and Print
Options” on page E-6 for more information.
5. Click Print.
A PHOTOSHOP progress dialog box appears.
To cancel printing, press the command key and type a . (period). If the cancel
command is ignored, select Cancel Printing in the PHOTOSHOP progress
dialog box.
October 2002
E-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PHOTOSHOP Export Module
Dialog Boxes and Print Options
This section describes the dialog box that allows you to specify print options.
KODAK LED Main Dialog Box
Option Descriptions
The Printer group box allows you to choose the following options:
Select—opens the Select a KODAK LED Printer dialog box.
Status—opens the Printer Status dialog box.
Defer Print—instructs the printer to “defer” printing the image until the printer
queue is full.
Reprint— allows you to print the last page sent to the printer. The last page sent
remains in the buffer until the printer is shut off, the computer is restarted, or the
next page is sent. If a page is not stored on the selected printer, the printer ignores
the request.
NOTE: The page that prints is the last one sent and stored in the printer. This may
or may not be the last page you sent. In network environments, another job
could have been sent to the printer after you sent yours.
E-6
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PHOTOSHOP Export Module
Other options
The other selections you can make from the KODAK LED Printer main dialog box
include the following options:
Copies— allows you to specify the number of
copies. Up to 99 copies can be printed at a time.
The default is 1.
Print—sends the job to the printer.
Cancel—closes the dialog box without printing the
image or saving changes.
Help—opens a Help dialog box so you can find
information about the Export Module within the
software program.
Punch Attributes
Option Descriptions
The Punch Attributes group box provides the following options to punch the paper
on 20R Printer only:
ID—places a page identification punch on the page that you are about to send.
End Order—Inserts an end of order punch on the paper web after the page you
are about to send.
NOTE: The ID and end order punches may be on the same side or on the opposite
sides of the paper, depending on how your printer is configured.
October 2002
E-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PHOTOSHOP Export Module
Page Layout Attributes
Option Descriptions
The Page Layout Attributes group box allows you to manipulate the position of the
image on the page.
Center—centers the image within the specified border.
Border—specifies the number of pixels of white border that should surround the
image on the page. This box is only active when the center box (above) is
checked.
Scale 200%—allows you to scale the image 200%.
Select an LED Printer Dialog Box
The Select a KODAK LED Printer dialog box is shown below, and it is accessed
by clicking Select in the KODAK LED Printer main dialog box.
This dialog box displays the KODAK LED Printer connected to the SCSI ports on
the MACINTOSH System.
E-8
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PHOTOSHOP Export Module
Option Descriptions
The following are descriptions of the options in the Select a KODAK LED Printer
dialog box:
Update—refreshes the screen and replaces any information that has changed.
Cancel—closes the Select a KODAK LED Printer dialog box without changing the
current printer selection.
OK—closes the Select a KODAK LED Printer dialog box.
Printer Status Dialog Box
Selecting the Status button to open the status dialog box in the KODAK LED
Printer main dialog box.
The Printer Status dialog box appears. The information that appears corresponds
to the printer currently selected for printing.
October 2002
E-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PHOTOSHOP Export Module
Option Descriptions
The following are descriptions of the options in the Printer Status dialog box:
Printer Information—describes the state of the selected proofer. The color of the
status field appears black if the proofer is idle, red for error conditions, and blue if
the printer is processing or printing. Information includes the printer model, print
media, print location, amount of RAM installed on your system, and the printer
version number.
Job Information—lists the number of jobs being processed.
Update—refreshes the screen and replaces any information that has changed.
OK—closes the Printer Status dialog box.
Troubleshooting
Error messages
Many of the error messages displayed by the Export Module are self explanatory.
The following list provides additional information about some of the more
frequently encountered messages. If you do not find an error message in the list,
refer to your MACINTOSH or PHOTOSHOP Documentation.
A good approach for troubleshooting errors is to:
1. Check all connections.
2. Make sure the printer is in raster mode.
3. Make sure that the display shows the READY prompt.
If the problem persists, restart the printer and the computer. If you still have
trouble, try reinstalling the Export Module.
General error messages
The image is not in RGB Color!
Convert to RGB Color in PHOTOSHOP before printing (exporting).
Change the color mode using the PHOTOSHOP Mode menu.
The file is too large for the paper installed!
Resize the image in PHOTOSHOP before printing.
Change the size of the image using the PHOTOSHOP Mode menu.
A printer must be selected to continue to the Print dialog box.
Select a printer or use Cancel to exit PHOTOSHOP.
This message occurs when a printer has not been selected and the user is
attempting to proceed to the Print dialog box from the Select dialog box. Click OK
to close the error dialog box and return to PHOTOSHOP.
E-10
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the PHOTOSHOP Export Module
There are no printers found attached to the host computer.
Check the connections and power to each printer.
Check that the connections to each printer, including the SCSI cables and power
cables, are properly connected.
The previously selected SCSI printer is no longer available or has been
changed.
This message occurs if the SCSI printer that you selected is no longer available.
Click OK to open the print dialog box.
The selected printer is not available!
Check the connections and make sure the printer is turned on or, select
another printer.
This message occurs when the selected printer is not connected or is turned off
when Print is selected. Click OK to return to close the error dialog box and return
to the print dialog box.
The number of border pixels exceed the maximum printer page size, reduce
the number of pixels.
This message occurs when the borders control causes the page limits in the printer
to be exceeded. Click OK to close the error dialog box and return to PHOTOSHOP.
Other Problems
“On-Line Pages Deferred” appears, But Jobs Are Not Printing
If jobs were sent with the “Defer Print” option, the printer is waiting for more data
to fill the frame store. If you wish to print these jobs in the frame store:
1. Select the “Reprint” box in the Export Module.
2. Set the number of copies to 0.
3. Deselect the Defer Print key.
4. Click Reprint in the Export Module to instruct the printer to print the frames
that are currently being stored.
or
1. Press On/Off Line on the printer’s OCP to take the printer offline.
2. Press Menu.
3. Follow the instructions on the printer’s OCP.
October 2002
E-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
wash/stabilizer setup 3-44
chemical
filters, replacing 4-10
residue, cleaning 4-13
chemistry
adding 4-14
levels 4-4
circulation, checking 4-7
cleaning
A
access, operator and service B-2
adding
calibration device C-7
new chemistry 4-14
air filter, replacing 4-3
algae, preventing 4-8
arrow keys, printer 3-3
Asian helpline number 5-33
automatic initialization, printer 5-2
corrosion 4-13
crossover assemblies 4-5
crossover assemblies and racks 4-8
entrance sensors 4-9
feed table 4-9
tank and dryer cover 4-12
clearing
B
bleach/fix, mixing 4-15
borderless prints 3-20
buffered jobs, printing 3-4
drive errors 5-20
error messages, processor 5-19
paper jams, printer 5-11
paper jams, processor 5-20
reset messages, processor 5-19
C
computer
reset, processor 3-43
configuration
editing the printer calibration C-16
control strip
feed box 3-32
processing 3-32
corrosion, cleaning 4-13
covers, cleaning 4-12
calibrate mode, processor 3-26
calibrating
development time 3-40
printer, procedure 2-5
replenishment flow rate 3-39
temperatures 3-37
temperatures, processor 3-36
calibration
printer, advanced features C-11
printer, editing the configuration C-16
software, device C-3
calibration troubleshooting
MACINTOSH 5-23
WINDOWS NT 5-30
cancel key, printer 3-3
canelling jobs 3-4
crossover assemblies, cleaning 4-5, 4-8
D
daily maintenance
printer 4-2
processor 2-3, 4-4
date
setting, printer 3-17
viewing/setting, processor 3-34
defaults
cassettes
managing 3-6
supply, installing 3-10
supply, loading paper 3-7
supply, removing 3-6
chad, removing 3-13, 4-2
chain
greasing 4-11
tension 4-7
changing
processor 3-43
deferred jobs, printing 3-4
deleting a calibration device C-10
densitometer
installing C-25
type B-13
density source, attribute description C-17
metric/fahrenheit mode 3-44
October 2002
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
developer, mixing 4-14
developer/replenisher, mixing 4-14, 4-15
development time
F
feed
box, control strip 3-32
table, cleaning 4-9
file format
calibrating 3-40
managing 3-40
tolerance, setting 3-45
device calibration software C-3
addiing calibration device C-7
application window definitions C-3
deleting a calibration device C-10
editing log settings C-8
starting C-6
updating a calibration device C-9
diagnostics 5-1
dialog boxes
IPS D-10
file formats
MACINTOSH C-19
WINDOWS NT C-22
filters
air, replacing 4-3
chemical and wash, replacing 4-10
floor requirements B-2
formats
file, MACINTOSH C-19
file, WINDOWS NT C-22
Export Module E-8
dialog boxes, IPS D-6
dimensions B-1
down key, processor 3-27
drive
G
control, processor 3-42
errors, clearing 5-20
getting additional help 5-32
graphing, attribute description C-17
graphs, viewing C-11
key/light, processor 3-28
dryer cover, cleaning 4-12
H
E
editing
hardware requirements, Export Module E-2
helpline numbers 5-33
humidity specifications, processor B-12
log setting, calibration device C-8
printer calibraition configuration C-16
effluent chemical levels 4-4
electrical requirements B-4
end of the roll of paper 3-12
entrance sensors, cleaning 4-9
equipment overview 1-4
error
drive 5-20
light, printer 3-3
observable, printer 5-12
error messages
I
image print server, using D-3
images, source 1-2
initialization, printer 5-2
input code values, attribute description C-17
installing
densitometer C-25
Export Module E-2
supply cassettes 3-10
interface, SCSI 1-2
introduction 1-1
clearing for the processor 5-19
Export Module E-14
printer 5-4
processor 5-17
IPS
European region helpline number 5-33
Export Module
attended operation D-4
dialog boxws and print options D-6
enqueue D-5
enqueue dialog box D-7
failed jobs D-4
dialog boxes and print options E-8
installing E-2
troubleshooting E-14
file format D-10
initialize default parameters dialog box D-9
LZW compression D-10
Index-2
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
menu bar insertion D-3
print queue D-3
server default dialog box D-8
source directory insertion D-3
suspending and resuming D-4
using D-3
menu
key, printer 3-3
printer 3-4
messages
error, processor 5-17
status, printer 3-5
status, processor 3-28
messages, printer error 5-4
metric, changing to 3-44
min max
J
jams
paper, clearing for the printer 5-11
paper, clearing for the processor 5-20
mode, processor 3-26
temperatures, resetting 3-37
mixing solutions 4-14, 4-15
mode
calibrate 3-26
min max 3-26
offline/online, printer 3-4
operational 3-30
K
keep history, attribute description C-17
keep log, attribute description C-17
key operator mode 3-30
processor 3-26
set, processor 3-26
modem
port, resetting 3-16
monthly maintenance
, processor 4-11
L
leaks, checking the fittings 4-10
levels
mottle 4-6
chemistry 4-4
replenishment and effluent chemical 4-4
light on/off for the processor 3-29
line frequency B-6
N
next print 3-2, 3-3
line voltage B-10
loading paper into supply cassettes 3-7
log
file name, attribute description C-17
type, attribute description C-17
LUTs
O
observable errors, printer 5-12
OCP
resetting 3-23
sending C-14
key/light descriptions, printer 3-3
key/light descriptions, processor 3-27
on/off light, processor 3-29
printer 3-2
offline
M
printer 3-4
printer mode 3-4
on/off
main drive chain
greasing 4-11
tension 4-7
key, printer 3-3
maintaining
key/light, processor 3-27
online, printer mode 3-4
operating
environment B-11
the processor 3-26
operational checks, processor 4-6
operator
printer 4-2
processor 4-4
the equipment 4-1
making prints
MACINTOSH version 2-12
material key/light for the processor 3-28
material sensors 3-41
maximum cycles, attribute description C-17
access B-2
mode 3-30
October 2002
Index-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
operator control panel
on/off line key 3-3
key/light descriptions, printer 3-3
key/light descriptions, processor 3-27
printer 3-2
operator control panel 3-2
overview 1-2
paper path, illustration 5-3
periodic maintenance 4-3
power light 3-3
out of paper, message 3-12
out of tolerance, attribute description C-17
overview, equipment 1-4
resetting parameters 3-23
select key 3-3
setting time and date 3-17
shutting down 2-15
specifications B-1
standby light 3-3
start key 3-3
starting up 2-4
status messages 3-5
troubleshooting tips 5-16
P
Pacific region helpline number 5-33
page layouts, Export Module E-11
page starts value, setting 3-20
pages waiting 3-2
paper
end of roll 3-12
printing
jams, clearing for the printer 5-11
jams, clearing for the processor 5-20
length, setting 3-18
loading into supply cassettes 3-7
path, printer illustration 5-3
setting slug width 3-19
supply 3-2
aims, attribute description C-17
deferred or buffered jobs 3-4
images, Export Module E-5
prints
making, MACINTOSH version 2-12
prints, borderless 3-20
processing a control strip 3-32
processor
width 3-2
parameters, resetting for the printer 3-23
periodic maintenance
printer 4-3
clearing error messages 5-19
clearing paper jams 5-20
clearing reset messages 5-19
computer, reset 3-43
processor 4-13
plumbing B-3
port
daily maintenance 2-3, 4-4
defaults 3-43
modem, resetting 3-16
SCSI, selecting 3-14
power
drive control 3-42
error messages 5-17
maintaining 4-4
cords B-5
light, printer 3-3
outlets B-6
monthly maintenance 4-11
OCP key/light descriptions 3-27
OCP on/off light 3-29
receptacles B-7
operating procedures 3-26
operational checks 4-6
overview 1-3
periodic maintenance 4-13
recommended settings 4-16
shutting down 2-13
specifications B-1
speed, checking and adjusting 4-11
starting up 2-2
preventing algae 4-8
print options, IPS D-6
printer
arrow keys 3-3
calibrating procedure 2-5
calibration, advanced features C-11
cancel key 3-3
clearing paper jams 5-11
daily maintenance 4-2
error light 3-3
status messages 3-28
tanks, cleaning 4-13
error messages 5-4
menu 3-4
menu key 3-3
observable errors 5-12
OCP key/light descriptions 3-3
offline 3-4
testing 4-6
troubleshooting tips 5-21
weekly maintenance 4-7
processor in control, attribute description C-17
product description 1-2
punch attributes, Export Module E-10
Index-4
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
temperatures 3-36
time and date, processor 3-34
seven day timer
viewing/setting, processor 3-35
shutting down
printer 2-15
processor 2-13
site requirements B-2
slug width 3-19
slug width, setting 3-19
software
R
racks, cleaning 4-8
Raster Mode
Placing your Printer E-3
recommended processor settings 4-16
removing
chad 3-13, 4-2
supply cassette 3-6
replacing
air filter 4-3
chemical and wash filters 4-10
replenishment
device calibration C-3
identification, viewing 3-36
software requirements, Export Module E-2
solutions
checking the temperature 4-11
mixing 4-14, 4-15
source images 1-2
specifications
chemistry levels 4-4
flow rate, calibrating 3-39
key/light, processor 3-27
rate, viewing and setting 3-38
reset
keys processor 3-28
messages, clearing for the processor 5-19
min max temperatures 3-37
residue buildup, cleaning 4-13
roll of paper, end 3-12
electrical B-4
floor requirements B-2
humidity, processor B-12
line frequency B-6
line voltage B-10
operating environment B-11
operator and service access B-2
plumbing B-3
S
SCSI
power cords B-5
interface 1-2
power outlets B-6
power receptacles B-7
printer/processor B-1
telephone line B-13
venting B-11
ports, selecting 3-14
select key, printer 3-3
selecting
SCSI ports 3-14
slug width 3-19
wash chemicals B-12
speed, of the processor 4-11
splash guard 2-14
stabilizer, mixing 4-15
standby light, printer 3-3
start key, printer 3-3
starting
target pad read options 3-14
sending
LUTs C-14
test targets C-15
sensors, material 3-41
service
access B-2
how to obtain 5
mode 3-30
device calibration software C-6
printer 2-4
processor 2-2
set
status messages
key, processor 3-27
mode, processor 3-26
setting
printer 3-5
processor 3-28
supply cassettes
development time tolerance 3-45
page starts value 3-20
paper length 3-18
printer time and date 3-17
processor, recommended 4-16
replenishment rates 3-38
seven day timer, processor 3-35
installing 3-10
loading paper 3-7
removing 3-6
October 2002
Index-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
seven day timer, processor 3-35
software identification 3-36
temperatures 3-36
T
tank cover, cleaning 4-12
tanks, cleaning 4-13
time and date, processor 3-34
target
height, attribute description C-17
width, attribute description C-17
target pad read options, selecting 3-14
telephone line B-13
W
wash
chemicals, enviromental specifications B-12
temperatures
calibrating 3-37
filters, replacing 4-10
wash/stabilizer setup, changing 3-44
weekly maintenance, processor 4-7
weight B-1
calibrating, processor 3-36
key/light, processor 3-27
resetting min max 3-37
solutions, checking 4-11
viewing/setting 3-36
width, paper 3-2
tension, main drive chain 4-7
test target, attribute description C-17
test targets, sending C-15
testing the processor 4-6
The C-17
time
key/light, processor 3-27
setting, printer 3-17
viewing/setting, processor 3-34
timer
seven day, setting/viewing 3-35
tolerances, attribute description C-17
transport racks, cleaning 4-8
troubleshooting
calibration 5-22
Export Module E-14
getting additional help 5-32
observable errors, printer 5-12
processor calibration, MACINTOSH 5-23
processor calibration, WINDOWS NT 5-30
tips for the printer 5-16
tips for the processor 5-21
U
up key, processor 3-27
updating a calibration device C-9
using the image print server (IPS) D-3
V
venting B-11
view mode, processor 3-26
viewing
graphs C-11
replenishment settings 3-38
Index-6
October 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
EASTMAN KODAK COMPANY
Rochester, New York 14653
U.S.A.
KODAK CANADA INC.
Toronto, Ontario M6M 1V3
Canada
Kodak, Portra, Supra, Gold, Ektacolor,
Prime and Kodak Professional are
trademarks of
Eastman Kodak Company
©Eastman Kodak Company, 2002
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|