KOBE Brand Range Hood
Model No. RA3830SQD
RA3836SQD
RA-038 SERIES – 5” HEIGHT
“RECIRCULATING HOOD”
INSTALLATION INSTRUCTIONS
AND OPERATION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY,
OBSERVE THE FOLLOWING:
1) Installation and electrical wiring must be done by qualified professionals and in accordance
with all applicable codes and standards, including fire-rated construction.
2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or
other hidden utilities.
3) Before servicing or cleaning unit, SWITCH POWER OFF AT SERVICE PANEL.
4) Clean fan, filter, if any, and grease laden surfaces frequently.
NOTE - This warranty is invalid without an authorized agent’s
receipt or if unit is damaged due to misuse, poor
installation, improper use, mistreatment, negligence or
any other circumstances beyond the control of KOBE
RANGE HOODS authorized agents. Any repair carried
out without the supervision of KOBE RANGE HOODS
authorized agents will automatically void the warranty.
- KOBE RANGE HOODS will not be held responsible for
any damages to personal property or real estate or any
bodily injuries whether caused directly or indirectly by
the range hood.
WARNING – TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE
TOP GREASE FIRE:
•
•
•
Keep fan, filter, if any, and grease-laden surfaces clean.
Always turn hood ON when cooking at high heat.
Use high settings on cooking range ONLY when necessary. Heat the oil slowly on low to
medium setting.
•
•
•
•
Do not leave cooking range unattended when cooking.
Always use cookware and utensils appropriate for the type and amount of food prepared.
Use this unit only in the manner intended by the manufacturer.
Before servicing, switch power off at service panel and lock service panel (if possible) to
prevent power from switching on accidentally.
•
Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan, filter
and oil containers.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
What to Do In The Event Of a Range Top Grease Fire
-
SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal tray, and then turn off the
burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If
the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE
DEPARTMENT or 911.
- NEVER PICK UP A BURNING PAN – You may get burned.
DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.
-
- Use an extinguisher ONLY if:
a) You have a Class A, B, C extinguisher and know how to operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.
What to Do If You Smell Gas
-
-
Extinguish any open flame.
Do not try to turn on the lights or any type of appliance.
- Open all doors and windows to disperse the gas. If you still smell gas, call the Gas
Company and Fire department right away.
CAUTION
1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials
and vapors.
2) To reduce the risk of fire, use only metal ductwork.
3) Follow the heating equipment manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.
4) Activating any switch may cause ignition or an explosion.
ELECTRICAL SHOCK HAZARD – Can result in serious injury or death.
Disconnect appliance from electric power before servicing.
If equipped, the fluorescent light bulb contains small amounts of mercury,
which must be recycled or disposed of according to Local, State, and
Federal Codes.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
(M ust keep all m aterial for returns or refunds)
Range Hood Box
Duct Cover Box (Sold Separately)
{A} KOBE Range Hood
{B} Warranty Registration Card
{C} Instructions Manual
{D} Plastic Plate
{F} KOBE Duct Cover (Model No. RA1020DC)
{G} Screws Package
{H} Duct Cover-Mounting Bracket
{I} Hood-Mounting Bracket
{E} Charcoal Filter Set
(Model No. RH-CF01)
- Charcoal Filter x 2
- Mesh Filter x 2
- Safety Screen x 2
- Oil Container x 2
- Screw x 2
{A}
{F}
{B}
{C}
{G}
{H}
{D}
{E}
{I}
***Only used with purchase
of duct cover.
***Attached to hood
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING
Calculation before Installation
Calculate the length of the installation, before installing the hood. (All calculation is measure in
inches.)
- FOR UNDER THE CABINET -
TABLE 1
A = Height of Floor to Ceiling
B = Height of Floor to Counter Top
(Standard: 36”)
C = Preferred Height of Counter Top
to Hood Bottom (Recommended
27” to 30”)
D = Height of Hood
E = Height of the Cabinet
- FOR STAND ALONE (WITH OPTIONAL DUCT COVER) -
TABLE 2
A = Height of Floor to Ceiling
B = Height of Floor to Counter Top
(Standard: 36”)
C = Preferred Height of Counter Top
to Hood Bottom (Recommended
27” to 30”)
D = Height of Hood
E = Height of Duct Cover [F – D]
F = Height of the Hood Installation
[A – (B+C)]
4
Download from Www.Somanuals.com. All Manuals Search And Download.
UNDER THE CABINET INSTALLATION
SAFETY WARNING
HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT
IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING, OR
SERVICING.
Preparation before Installation
- Temporarily wire the hood to test for proper operation before installing.
- Peel protective film off the hood (if any).
- For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler
strips (not included) on each side. Refer to Figure 1.
- Measure and create access opening for electrical wires under the cabinet.
Hood Installation
CAUTION: If required to move the cooking range to install the hood, turn off the power on an
electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS
RANGE.
1. Puncture the knockout holes. Refer to Figure 2.
Figure 1
Figure 2
2. Unscrew the six screws on the bottom casing. Remove the bottom casing as shown in
Figure 3. If necessary, arrange the electrical wire to run through the 1” diameter hole on
the hood.
3. Use calculation on Table 1 and measurements on page 14 as references. Center the hood
in place beneath the cabinet and flush with the front of the cabinet. Refer to Figure 4.
Figure 3
Figure 4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Draw electrical wires through cabinet access opening.
5. Place screws (not provided) into the exact center of each knockout hole. Make sure all
screws are in place before tightening screws. CAUTION: MAKE SURE THE HOOD IS
SECURE BEFORE RELEASING.
6. Connect the electrical wires. Refer to “Wiring to Power Supply.” If necessary to hide the
electrical wire connections, push wires back into the wiring box. Access the wire
connections underneath the hood by removing the bottom casing from the six screws.
Before reattaching the bottom casing, make sure wires do not slip between motors,
impellers, or any moving parts to prevent any damage. NOTE: Be careful when using
electrical screwdriver, damage to the hood may occur.
Wiring to Power Supply
SAFETY WARNING
RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED.
MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING
WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO
PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY.
-
-
-
Connect three wires (black, white and green) to house wires and cap with wire connectors.
Connect according to color: black to black, white to white, and green to green.
Test the operation of the hood before moving on to next step. Make sure power is supplied
to the hood.
Final Assembly
7. Turn power ON in control panel. Check all lights and fan operation.
8. Make sure to leave this manual for the homeowner.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STAND ALONE INSTALLATION
***This installation only applies with the purchase of an optional duct cover (Model No. RA1020DC).
SAFETY WARNING
HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT
IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR
SERVICING.
Preparation before installation
- Temporarily wire the hood to test for proper operation before installing.
- Peel protective film off the hood and the duct cover (if any).
- If necessary, prepare back wall frame with cross framing lumber for secure installation.
Using references on Table 2 and measurements on page 14, decide the level of the
lumber. Refer to Figure 5.
Hood Installation
CAUTION: If required to move the cooking range to install the hood, turn off the power on an
electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS
RANGE.
1. Remove the five screws at the center of the hood top. Use the five screws to attach the
plastic plate onto the hood as shown in Figure 6. NOTE: Disregard the hole through the
plastic plate.
2. If necessary, attach two rubber stands (provided) with two (4x8 mm) screws (provided) to
the back of the hood.
Figure 5
Figure 6
3. Attach the hood-mounting bracket to the back of the hood with six (3/16 x 3/8 mm) screws
(provided) as shown in Figure 7.
4. Use the references on Table 2 and the measurements on page 14 to decide the level of
the hood. Position two mounting screws (not provided) on the wall, leaving 1/8” away
from the wall. Refer to Figure 8.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting
Screws
Figure 7
Figure 8
5. Align hood-mounting bracket to the two screws on the wall and hook hood into place.
Tighten screws to secure hood to the wall. CAUTION: MAKE SURE THE HOOD IS
SECURE BEFORE RELEASING.
Duct Cover Installation
6. Mark the position of the duct cover-mounting bracket. Use reference E from Table 2 and
measurements on page14. Attach and secure duct cover-mounting bracket with two
screws (not provided). Refer to Figure 9. NOTE: Inner duct cover will cover the duct
cover-mounting bracket.
7. Connect electrical wires. Refer to “Wiring to Power Supply.” If necessary to hide the
electrical wire connections, push wires back into the wiring box. Access the wire
connections underneath the hood by removing the bottom casing. Before reattaching the
bottom casing, make sure wires do not slip between motors, impellers, or any moving
parts to prevent any damage. NOTE: Be careful when using electrical screwdriver,
damage to the hood may occur.
8. Slide the inner duct cover up 2 inches before sliding entire duct cover onto the hood.
Refer to Figure 10.
Figure 9
Figure 10
9. Adjust the height of the inner duct cover to the duct cover-mounting bracket. Secure
inner duct cover with two (4x8 mm) screws (provided) as shown in Figure 11.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach Together
Figure 11
10. Fasten outer duct cover to plastic plate on the hood with four (4x8 mm) screws (provided).
Wiring to Power Supply
SAFETY WARNING
RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED.
MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING
WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO
PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY.
-
-
-
Connect three wires (black, white and green) to house wires and cap with wire connectors.
Connect according to color: black to black, white to white, and green to green.
Test the operation of the hood before moving on to next step. Make sure power is supplied
to the hood.
Final Assembly
11. Turn power ON in control panel. Check all lights and fan operation.
12. Make sure to leave this manual for the homeowner.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
This KOBE hood is equipped with four electronic controls with a 10-second standby startup &
30-second delay shutoff, two powerful centrifugal turbine impellers with charcoal filter set, and
two bright 12-volt 20-watt halogen lights.
The four button controls are Light Control, Speed Control A (cycles through Low, Medium,
High, QuietMode), Speed Control B (cycles through Low, QuietMode, High, Medium) and
the Power Control (On/Off). Refer to Figure 12.
Figure 12
Light Control
Power Control
Speed Control A
Speed Control B
(Cycles through Low, Medium, High, QuietMode) (Cycles through Low, QuietMode, High, Medium)
Turn On:
-
-
-
-
Press Power Control (On/Off) button once. (If any Control button is not pressed
within 10 seconds, power will be automatically turned off).
The KOBE hood will start on Low speed. Each press of the Speed Control button
will cycle through the various speeds.
Press Speed Control A button to cycle from Low, Medium, High, or QuietMode.
Press Speed Control B button to cycle from Low, QuietMode, High or Medium.
Press Light Control button to turn halogen light on.
Turn Off:
-
Press Power Control (On/Off) button once, panel lights will flash and power will be
completely shut off after 30 seconds.
OR
-
-
Press Power Control (On/Off) button twice, all power will be shut off immediately.
If only the lights are on, pressing Power Control (On/Off) button once will turn power
off after 30 seconds.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: NEVER PUT YOUR HAND INTO THE AREA HOUSING THE FAN WHILE THE
FAN IS OPERATING.
For the optimal level of operation, clean the range hood surface, charcoal filter unit, and oil
containers regularly.
To Clean Hood Surface
CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS.
*** Regular care will help preserve its fine appearance.
1) Use only mild soap or detergent solutions. Dry surfaces using soft cloth.
2) If hood looks splotchy (stainless steel hood), use an orange base cleaner to clean the
surface of the hood. Avoid getting cleaning solution on the control switches. Only
spread a light coating over the surface of the hood and leave on for a few minutes (do
not leave on too long or this may cause damage to hood finish). Use soft towel to wipe
off the cleaning solution, gently rub off any stubborn spots. Use a slightly damp towel to
get rid of any cleaning solution. Use dry soft towel to dry the hood.
3) To bring the glow back into a stainless steel finish, use a stainless steel cleaner.
4) DO NOT allow deposits to remain for long periods of time.
5) DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the
surface and cause rust.
6) DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain
in contact with stainless steel for extended periods. Many of these compounds contain
chemicals, which may be harmful. Rinse with water after exposure and dry with a clean
cloth.
To Clean Charcoal Filter Set and Oil Containers
CAUTION: DRAIN OIL CONTAINER BEFORE OIL CAN OVERFLOW.
1) Cleaning Charcoal Filter Set
-
Remove the safety screen screw and slide the charcoal filter set out. Remove oil
container (round) by turning counter-clockwise.
-
-
Wash with warm soapy water. Dry completely before returning into place.
Top rack dishwasher safe.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
To Replace Light Bulb
CAUTION: HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL.
1) Make sure all control switches are off, and range hood is unplugged.
2) Use a flat head screwdriver to pop out the protective covering as shown on Figure 13.
3) Gently pull out the defective light bulb and discard. Light bulb should be 12V 20W
maximum. Refer to Figure 14. Push bulb securely into light socket.
4) Replace protective cover.
5) Plug in range hood.
Figure 13
Figure 14
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL / SIZE
RA3830SQD / 30”
RA3836SQD / 36”
COLOR
# 430 Commercial Grade Stainless Steel
VOLTAGE
120V 60Hz
NUMBER OF MOTORS
DESIGN
2
18-Gauge Seamless
FAN TYPE
EXHAUST
CONTROL
Twin Turbine Impeller
Ductless with Charcoal Filter Set
Electronic Control (4 Buttons) –
10-Second Standby Startup
30-Second Delay Shutoff
HALOGEN LIGHT
12V 20W x 2
HOOD DIMENSION
(W x D x H)
(RA3830SQD) 29-3/4” x 20-1/2” x 5-1/8”
(RA3836SQD) 35-1/4” x 20-1/2” x 5-1/8”
OPTIONAL ACCESSORIES
(W x D x H)
1) Two-Piece Adjustable Duct Cover
(RA1020DC) 10-5/8” x 9-1/8” x (22-7/8” ~ 39-5/8”)
2) 30” Stainless Steel Back Panel
(SSP30) 30” x 1/10” x 32”
3) 36” Stainless Steel Back Panel
(SSP36) 36” x 1/10” x 32”
Net
36.3
39.6
Gross
40.7
44.0
WEIGHT (lbs)
RA3830SQD
RA3836SQD
SPEED
Air Capacity (cfm)*
Sone
Low
200
2.8
Medium
330
4.0
High
400
4.6
QuietMode
150
2.0
*In House Test Static Pressure “0”.
**Specifications subject to change without notice.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
***All inch measurements are converted from millimeter. Inch measurements are estimated.
***All measurements in ( ) are millimeters.
- FOR UNDER THE CABINET -
30” = Knockout Holes “A”
36” = Knockout Holes “A” & “B”
- FOR STAND ALONE (WITH OPTIONAL DUCT COVER) -
***Hood-Mounting Bracket
***Duct Cover-Mounting Bracket
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL NO.: RA3830SQD
RA3836SQD
NO.
1
DESCRIPTION
Hood Casing
MODEL /SIZE
RA3830SQD
RA3836SQD
PART NO.
10-03300-F
10-03360-F
2
A
B
C
Air Chamber
Air Chamber (Top)
Air Chamber (Side)
Air Chamber (Opening)
Motor (Right)
Motor (Left)
Impeller (Right)
Impeller (Left)
Impeller Plastic Cover
Oil Tunnel
C1-0102-0770F
C1-0101-0770F
C1-0241-0770FA
C1-0301-0120-08A
C1-0301-0120-07A
C1-0251-0092-02
C1-0251-0092-01
C1-0251-0001
3
4
5
6
7
8
C1-0502-0201
9
10
Flat Head Screws (3/16” x 5/8”)
Bottom Casing
C1-0704-0001
RA3830SQD
RA3836SQD
B101-0330-09F
B101-0336-09F
C1-0403-0101
C1-0401-0120-01A
C1-0402-A120-04
C1-0402-0120-40
C1-0501-0102
C1-0404-0401-B
C1-0708-0003
C1-0501-0101
11
12
13
14
15
16
17
18
19
20
A
Halogen Light (12V 20W Max.)
Capacitor
Transformer (Motor)
Transformer (Halogen Light)
Processor Board Box
Processor Board
Round Head Screw (TS 1/8” x 3/8”)
Control Unit
Control Board
C1-0404-0401-A
Charcoal Filter Set
Charcoal Filter
Mesh Filter
RH-CF01
MF-0201
C1-0603-0302
C1-0604-0201
C1-0602-0202
C1-0503-0201
C1-0705-0001
C1-0507-0201
B
C
D
E
Safety Screen
Oil Container (Round)
Safety Screen Screw
Plastic Plate
21
(Optional Duct Cover)
NO.
22
23
24
25
DESCRIPTION
MODEL /SIZE
PART NO.
Hood-Mounting Bracket
Round Head Screw (TS 4 x 8 mm)
Duct Cover
C1-0221-0330
C1-0708-0006
12-02000-430
C1-0203-0002
RA1020DC
Duct Cover-Mounting Bracket
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL NO.: RA3830SQD
RA3836SQD
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL NO.: RA3830SQD
RA3836SQD
17
Download from Www.Somanuals.com. All Manuals Search And Download.
1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING
DELIVERY. NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS
RECEIPT. REQUEST NAME AND SIGNATURE OF THE CARRIER’S AGENT AND
KEEP COPY TO SUPPORT YOUR CLAIM.
Upon acceptance of items, owner assumes responsibility for its safe arrival. Damages
should be reported to carrier and a claim filed. Failure to do this could result in the
carrier refusing to honor your claim. The carrier will furnish you with necessary forms
for filing a claim.
DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR
WARRANTY.
2. PLEASE INSPECT CONTENTS OF PACKAGE (S) CAREFULLY UPON RECEIVING!
We must be notified in writing of any damages and/or missing parts within the allocated
days upon receipt of package(s). Contact your local KOBE dealer or distributor or call
KOBE for the time limit.
CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS.
NOTE: ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR
FACTORY.
3. Products must be returned in good working condition with ALL original parts and
documentation packed in ALL original cartons, fillers and shipping cartons. A restocking
fee of 25% will be charged for all approved return(s).
EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS
MISSING.
4. MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE
INSTALLATION. Appearance flaws of the hood found after installation and not
affecting hood performance is not covered under our warranty for returns or exchanges.
Service visits not covered under warranty will carry a service charge.
A) Before Installation: Return for exchange or refund (please see above for
acceptable returns).
B) After Installation: NO exchange or refund.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CERTIFICATE
KOBE Range Hoods, Inc. warrants all products manufactured or supplied by it to be free from
defects in workmanship and materials. Its obligations pursuant to this warranty are limited to a
period of two years from the date of purchase and to the repair or replacement at its option and
subject to the terms and conditions stated below, of any component part, which its examination
shall disclose to be so defective.
TWO-YEAR WARRANTY SERVICE PERIOD
Any covered failure occurring within two years of original purchase arising from defective
workmanship or material in manufacture will be repaired (or at our option the unit will be
replaced) free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods
as applicable. Keep proof of purchase (or original invoice) handy for inspection.
If the range hood is sold by the original purchaser during the warranty period the new owner is
protected until expiration of the original purchaser’s warranty.
CONDITIONS
The following conditions apply only in relation to the warranty expressly given in this certificate.
1) This warranty applies only:
a) within U.S.A. and Canada.
b) to range hoods used for PRIVATE SINGLE FAMILY USE (if used for COMMERCIAL or
MULTIPLE FAMILY USE or other purposes, warranty will be voided).
2) Repair of any fault to be provided under this warranty shall not be provided:
a) if the identification number attached to the range hood has been altered, rendered
illegible or removed;
b) if notice of the defect has not been given within the period applicable;
c) for failure of light bulbs;
d) for physical damage;
e) for surfaces damaged by use of improper chemical cleaning agents;
f) if the appliance has been:
i) subject to misuse, abuse, negligence, accident, incorrect installation or failure to
follow the operating instructions;
ii) connected to improper, inadequate or faulty electricity service or exhaust ducts or
flues or operated using incorrect or contaminated lubricants;
iii) installed, maintained or operated otherwise than in accordance with the instructions
furnished by KOBE Range Hoods including the improper use of detergents,
bleaches, or cleaners.
g) for damage to range hood during transit, delivery, installation or removal;
h) for damage by or resulting from attempted repairs conducted by anyone other than our
Authorized Service Agent.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3) The purchaser shall be responsible for any expenses involved in making the range hood
readily accessible for servicing and where the range hood is installed outside the main
sales territory of the retailer or service territory of the nearest approved KOBE Range
Hoods Agent as applicable, for any traveling expenses and any costs of transporting the
range hood or parts thereof to and from the dealer or Service Agent
4) The purchaser must produce proof of purchase together with this warranty certificate when
making the claim.
5) Damages caused during shipment are not covered under our warranty.
CONSEQUENTIAL DAMAGE
The warrantor is not responsible for any consequential damage. SOME STATES DO NOT
ALLOW THE EXCLUSION OF CONSEQUENTIAL DAMAGE SO THE ABOVE EXCLUSION
MAY NOT APPLY TO YOU.
IMPLIED WARRANTIES/STATE LAW
Any implied warranties, including the implied warranty of merchantability and fitness for
purpose, imposed on the sale by the laws of the state of sale are limited to two year from the
date of original purchase. Some states do not allow limitations on the duration of implied
warranties. This warranty gives you specific legal rights, and may also have rights, which vary
from state to state.
SERVICE
For service contact:
KOBE Range Hoods, Inc.
4934 Walnut Grove Avenue
Suite 202
San Gabriel, CA 91776
U.S.A
Tel: (626) 309-1356 Fax: (626) 309-1366
Email: [email protected]
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Register Your Product!
Any covered failure occurring within two years of original purchase arising from defective
workmanship or material in manufacture will be repaired or at our option the unit will be
replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range
Hoods as applicable. Keep proof of purchase (original invoice) handy for inspection.
If the range hood is sold by the original purchaser during the warranty period the new
owner is protected until expiration of the original purchaser’s warranty. See warranty
section for complete warranty coverage information.
This appliance has been manufactured, tested, and inspected to the standards required by
KOBE Range Hoods.
PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF
PURCHASE TO:
KOBE Range Hoods, Inc.
4934 Walnut Grove Avenue
Suite 202
San Gabriel, CA 91776
RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD:
Model No. ________________________
Serial No. ________________________
Purchased Date
Purchased From:
_____/_____/_____
______________________________
______________________________
______________________________
IMPORTANT: PLEASE KEEP A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY
WHEN REQUESTING FOR SERVICE.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
|