Owner’s Manual
KF-2060
215-00132
11/06 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
THANK YOU for making this unit a part of your exercise program.
Keys Fitness assures the very best in value, appearance, durability
and biomechanics.
This manual will guide you through the assembly process. If at any
time you are having trouble with the assembly or use of this product, then
please contact us at our Keys Fitness Helpline. We have trained service techni-
cians on site to take care of you, our valued customer.
REGISTRATION CARD
To avoid unnecessary delays in warranty parts and to insure that a permanent
record of your purchase is on file with our company, be sure to send in the war-
of purchase.
KEYS FITNESS SERIES
QUESTIONS?
CALL
1-888-380-0482
Monday-Friday
8:30-5:30 Central Time
When calling please have the following product information available:
Model Name : KF-2060
Serial #:
Manufactured Date :
PO # :
Model Name Decal Location
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
Important Safety Information
Prior to assembly, remove components from the box and verify that all the listed parts were
supplied.
NOTE
:
Hand tighten bolts and nylon nuts until machine is fully assembled.
Read all precautions and instructions in this manual before using this equipment.
WARNING!
Before using this unit or starting any exercise program, consult your
physician. This is especially important for persons over the age of
35 and/or persons with pre-existing health problems. Keys Fitness
Products LP assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit
have read the Owner’s Manual and are familiar with safety informa-
tion and precautions.
SAFETY PRECAUTIONS
• This unit should only be used on a level surface and is intended for
indoor use only. Keys Fitness recommends an equipment mat be
placed under the unit to protect the floor or carpet and for easier
cleaning.
• Wear comfortable, good-quality walking or running shoes and
appropriate clothing. Do not use this unit with bare feet, sandals,
socks or stockings!
• Always examine your unit before using to ensure all parts are in
working order.
• Do not leave children unsupervised near or on the unit.
• Service to your unit should only be performed by an authorized
service representative, unless authorized and/or instructed by a
Keys Fitness technician. Failure to follow these instructions will void
the warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ
Assembly
Box 1
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂ
Assembly
Box 2
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢃ
Assembly
Box 3
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢄ
Assembly
Box 4
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢅ
Assembly
Box 5
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢆ
Assembly
Box 6
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Assembly
Box 8
Box 7
【52】5pcs
pcs
【52】5
Box 9
Box 10
pcs
【53】9
pcs
【53】9
Box 11
Box 12
pcs
【54】5
pcs
【54】5
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Assembly
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Assembly
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Assembly
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Assembly
Step 1
Attach Right Base Frame (4) to Rear Frame (1) using two Nuts (144), four Washers
(143), and two Bolts (137).
Attach Left Base Frame (8) to Rear Frame (1) using two Nuts (144), four Washers
(143), and two Bolts (137).
Insert Guide Rods (47) into Rear Frame (1). Next, slide Weight Stack Bumpers (99)
onto Guide Rods (47).
Attach Rear Upright (3) to Rear Frame (1) using two Nuts (144), four Washers (143),
and two Bolts (136).
Figure 1
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Assembly
Step 2
Slide the weight plates down the Guide Rods (47) in this order - five 15lb Plates (52), nine
10lb Plates (53), five 5lb Plates (54), and the Top Plate (55). Note: Number of weight plates
may vary depending on your specific configuration.
Attach Top Frame (2) to all four Guide Rods (47) and secure to Rear Upright (3) using two
Nuts (144), four Washers (143), and two Bolts (136).
Figure 2
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Assembly
Step 3
Attach Front Upright (19) to Seat Pad Support Receptacle (6) using two Nuts (144), four
Washers (143), and two Bolts (136).
Attach Seat Pad Support Receptacle (6) to Base Frame assembly using two Nuts (144), four
Washers (143), and two Bolts (136).
Figure 3
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Assembly
Step 4
Attach Main Upright (7) to Seat Pad Support Receptacle using two Nuts (126), four Washers
(125), and two Bolts (131).
Attach Right Top Frame (5) to Top Frame assembly using two Nuts (144), four Washers (143),
and two Bolts (137). Next, use two Washers (143), two Spring Washers (119), and two Bolts
(142) to connect Right Top Frame (5) to Main Upright.
Figure 4
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Assembly
Step 5
Slide Press Station Base Frame (11) over Press Arm Support (10). Next, attach both pieces
to Base Frame using two Nuts (144), four Washers (143), and two Bolts (134).
Install Left Top Frame over Press Arm Support (10) and Top Frame assembly. Secure top
section using two Nuts (144), four Washers (143), and two Bolts (137). Next, Secure lower
section using two Nuts (144), four Washers (143), and two Bolts (136). Secure top of Guide
Rods (47) using two Washers (143), two Spring Washers (119), and two Bolts (142).
Figure 5
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Assembly
Step 6
Attach Pec Dec Mount (21) onto Seat Pad Support Receptacle using two Nuts (144), four
Washers (143), and two Bolts (136). Secure in place with one Washer (129), one Spring
Washer (119), and one Bolt (137).
Figure 6
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Assembly
Step 7
Attach Right and Left Leg Hold Leg Frames (29 & 30) using two Nuts (144), four Washers
(143), and two Bolts (135).
Figure 7
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Assembly
Step 8
Slide the Right Pec Dec Arm (22) on to the shaft of the Pec Dec Mount. Secure the arm in
place using one Big Washer (102), one Washer (143), one Spring Washer (119), and one Bolt
(128).
Slide Pec Dec Handle Bar (24) onto the top of the Right Pec Dec Arm (22) and secure using
one Chrome Washer (101), one Washer (143), one Spring Washer (119), and one Bolt (128).
Repeat this step to complete the Left Pec Dec assembly.
Figure 8
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Assembly
Step 9
Attach Leg Extension Lever (20) to Seat Pad Support Receptacle (6) and secure using Shaft
(86), one Washer (117), one Spring Washer (118), and one Allen Bolt (98).
Slide Foam Frame w/ Shaft (26) through the Leg Extension Lever (20) and attach Foam
Frame w/o Shaft (25) to the other side. Insert Slip Tension Pin (85) through the hole where
the two foam frames meet.
Note: You may need to use a rubber mallet to install Slip Tension Pin (85).
Figure 9
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Assembly
Step 10
Align Press Arm (35) and Chest Press Cam (12) while inserting Press Station Shaft (38). Slide
Pillow Block Bearing (75) onto each side of Press Station Shaft (38) and secure the assembly
using two Chrome Washers (101), two Washers (143), two Spring Washers (119), and two Allen
Bolts (128).
Attach the entire assembly to Press Arm Support using four Nuts (126), eight Washers (125),
and four Bolts (130).
Figure 10
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Assembly
Step 11
Attach Bench Rear Frame (15) onto Bench Main Frame (13) and secure using two Nuts (144),
four Washers (143), and two Bolts (133).
Attach Bench Front Stabilizer (14) on to Bench Main Frame (13) using two Nuts (144), four
Washers (143), and two Bolts (136).
Figure 11
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Assembly
Step 12
Attach Bench Seat Pad Support (16) to Bench Main Frame using one Nut (126), two Washer
(125), and one Bolt (132).
Insert Bench Seat Pad Adjustment Bar (64) into Bench Main Frame and secure using one
Washer (125) and one Nut (126). Attach Spring (66) to Bench Main Frame and Bench Seat
Pad Adjustment Bar (64).
Note: Make sure adjustment bar is installed into adjustable slots on Bench Seat Pad
Support.
Figure 12
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Assembly
Step 13
Attach Bench Back Pad Support (17) to Bench Main Frame using one Nut (126), two Washers
(125), and one Bolt (132).
Attach Bench Back Pad Adjustment Frame (39) to Bench Back Pad Support (17) using one
Nut (126), two Washers (125), and one Bolt (132).
Figure 13
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Assembly
Step 14
Attach Bench Seat Pad (48), Bench Lower Back Pad (156) and Bench Back Pad (49) using six
Washers (143) and six Bolts (138).
Insert Foam Shaft (40) into Foam Adjustable Bracket (18). Next, attach Upholstered Roller
Pads (58) using the following hardware: four Plastic Washers (90), two Chrome Washers (101),
two Washers (143), two Spring Washers (119), and two Bolts (128).
Figure 14
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Assembly
Step 15
Attach Left and Right Squat Arms (36 & 37) to the Press Arm Assembly (35) using two Safety
Pins (73).
Next, slide Upholstered Roller Pad (58) onto each Squat Arm (36 & 37) and secure using two
Plastic Washers (90), two Chrome Washers (101), two Washers (143), two Spring Washers
(119), and two Bolts (128).
Figure 15
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Assembly
Step 16
Attach Back Pad (51) to Back Pad Adjustment Bracket (28) using two Washers (143) and two
Bolts (127).
Attach Seat Pad (50) to Seat Pad Support (27) using two Washers (143) and two Allen Bolts
(127).
Slide both assemblies into receptacles as shown in Figure 16.
Figure 16
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Assembly
Step 17
Slide two Upholstered Roller Pads (58) onto Foam Frames and secure using two Big Plugs
(89).
Slide the Long Foam Tube (34) through the hole in Seat Pad Support. Next, slide two Plastic
Washers (90), two Upholstered Roller Pads (58), and two Big Plugs (89) onto each end of Long
Foam Tube (34).
Next, slide two Upholstered Roller Pads (58) onto each side of Leg Hold Frames and secure
using two Big Plugs (89).
Figure 17
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Assembly
Step 18
Note: Stretch all cables out completely and make sure all twisting is removed before
installing.
Install Lat Cable (110) as detailed in Figure 18. Follow dotted lines to identify exact location
Start by threading cable end into Top Plate (55).
You will need the following for installation:
Pulley (57) - Qty. 7
Cable (110) - Qty. 1
Nut (144) - Qty. 7
Long Pulley Spacer (123) - Qty. 4
Longer Pulley Spacer (121) - Qty. 4
Washer (143) - Qty. 14
Bolt (134) - Qty. 2
Bolt (135) - Qty. 1
Bolt (136) - Qty. 1
Bolt (137) - Qty. 1
Bolt (141) - Qty. 2
Figure 18
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Assembly
Step 19
Note: This step is only used if you do not have the Leg Press 3 attachment. If you do have
Leg Press 3 attachment, please follow instructions located in that manual. Use the Cable
Adapter (124) in place of the pulley.
Note: Stretch all cables out completely and make sure all twisting is removed before
installing.
Install Leg Press Cable Substitute (113) as detailed in Figure 19. Follow dotted lines to
identify exact location of pulleys.
You will need the following for installation:
Cable Adapter (124) - Qty. 1
Cable (113) - Qty. 1
Pulley Bracket with Shaft (33) Qty. 1
Bolt (139) - Qty. 1
Washers (143) - Qty. 2
Nut (144) - Qty. 1
Nylon Locknut (143) - Qty. 1
Figure 19
Download from Www.Somanuals.co3m.3All Manuals Search And Download.
Assembly
Step 20
Note: Stretch all cables out completely and make sure all twisting is removed before
installing.
Install Low Row Cable (111) as detailed in Figure 20. Follow dotted lines to identify exact
Start by installing cable under the pulley at Leg Extension location.
You will need the following for installation:
Pulley (57) - Qty. 6
Cable (111) - Qty. 1
Nut (144) - Qty. 6
Long Pulley Spacer (123) - Qty. 4
Longer Pulley Spacer (121) - Qty. 2
Short Pulley Spacer (122) - Qty. 2
Cable Retainer Bracket (46) - Qty. 1
Bolt (134) - Qty. 1
Bolt (136) - Qty. 1
Bolt (137) - Qty 1
Bolt (138) - Qty. 1
Bolt (141) - Qty. 2
Washer (143) - Qty. 12
Figure 20
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Assembly
Step 21
Note: Stretch all cables out completely and make sure all twisting is removed before install-
ing.
Install Pec Dec Cable (112) as detailed in Figure 21. Follow dotted lines to identify exact
location of pulleys.
See Page 43 “Cable View” for more detail.
You will need the following for installation:
Cable (112) - Qty. 1
Pulley (57) - Qty. 3
Bolt (141) - Qty. 3
Washer (143) - Qty. 6
Nut (144) - Qty. 3
Philips Screw (103) - Qty. 2
Figure 21
Download from Www.Somanuals.co3m5. All Manuals Search And Download.
Assembly
Step 22
Note: Stretch all cables out completely and make sure all twisting is removed before
installing.
Install Long Chest Cable (114) as detailed in Figure 22. Follow dotted lines to identify exact
Start by installing cable into the “Press Station” weight stack.
You will need the following for installation:
Pulley (57) - Qty. 2
Cable (114) - Qty. 1
Nut (144) - Qty. 3
Washer (134) - Qty. 4
Bolt (141) - Qty. 3
Figure 22
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 23
Note: Stretch all cables out completely and make sure all twisting is removed before
installing.
Install Short Chest Cable (115) as detailed in Figure 23. Follow dotted lines to identify exact
Start by threading the cable into the floating pulley bracket.
You will need the following for installation:
Pulley (57) - Qty. 1
Cable (115) - Qty. 1
Nut (144) - Qty. 2
Washer (134) - Qty. 2
Bolt (141) - Qty. 2
Figure 23
Floating
Pulley
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Assembly
Step 24
Connect Long Lat Bar (43) to the Lat Cable (110) using two Gear Hooks (87) and Short Chain
(88).
Connect Ab Strap (60) or Lat Strap (61) to Low Row Cable (111) using one Gear Hook (87).
Connect Short Lat Bar (44) or Ankle Strap (62) to Low Row Cable (111) using two Gear
Hooks (87) and Long Chain (116).
Figure 24
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Assembly
Step 25
Install Weight Shrouds (41) to the left and right side of the weight stacks using four Washers
(117) and four Bolts (98).
Install Weight Shroud (42) to the center of both weight stacks and secure using four Washers
(117) and four Bolts (98).
Figure 25
Note: Tighten all hardware securely.
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Assembly
Congratulations!
You have completed the assembly of your new KF-2050.
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Weight Ratios
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Weight Stack Sticker Placement
Your new POWER SYSTEM unit can be purchased with either a 200 LB or 250
LB weight stack. Depending on which weight stack you have purchased will deter-
mine which weight stack sticker numbers will be used.
The weight stack images below show which weight stack sticker numbers are to be
used on your weight stack. Please note that these stickers should not be put on
until the entire unit has been assembled and all bolts and nuts have been tight-
ened.
200 LB Stack
250 LB Stack
10
10
15
20
30
40
20
25
30
50
35
60
45
70
55
80
65
90
75
100
115
130
145
160
175
190
205
220
235
250
85
95
105
115
125
140
155
170
185
200
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Top View
Download from Www.Somanuals.com. All Manuals Search And Download.
44
Exploded View
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Parts List
KF-2060 Parts List Rev A
Ref #
1
Part #
Description
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
2
4
1
1
1
1
2
2
19
10
3
1
2
1
4
1
1
1
1
1
1
1
1
3
2
1
2
2
4
2
4
8
1
1
1
17
Ref #
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
Part #
Description
Qty
1
223-01077 FRAME, REAR KF-2060
206-00056 SHORT HANDLE GRIPS KPS-1800
230-00022 SHAFT FOR LEG EXT. KPS-2050
210-00008 GEAR HOOK, KPS, 210-00008
229-00037 SHORT CHAIN
2
223-01078 FRAME, UP KF-2060
1
3
223-01079 UPRIGHT, REAR KF-2060
7
4
223-01080 FRAME, RIGHT BASE KF-2060
223-01081 FRAME, RIGHT TOP FOR GUIDE RODKF-2060
223-01093 RECEPTACLE, SEAT PAD SUPPORT KF-2060
223-01084 UPRIGHT, MAIN KF-2060
1
5
206-00390 PLUG, ROLLER PAD TUBE CAP, KF SERIES
206-00134 PLASTIC WASHER KPS-2050/1850
206-00489 PLUG 50 KF-2060
6
6
8
7
2
8
223-01085 FRAME, LEFT BASE KF-2060
223-01095 FRAME, LEFT TOP FRAME GUIDE ROD KF-2060
223-01092 SUPPORT, PRESS ARM KF-2060
223-01089 FRAME, PRESS STATION BASE KF-2060
219-00611 CAM, CHEST PRESS KF-2060
223-01086 FRAME, BENCH MAIN KF-2060
223-01087 FRAME, BENCH FRONT KF-2060
223-01088 FRAME, BENCH REAR KF-2060
219-00615 SUPPORT, BENCH SEAP PAD KF-2060
219-00614 SUPPORT, BACK PAD (BENCH) KF-2060
219-00617 BRACKET, ADJUSTABLE FOAM KF-2060
223-00956 UPRIGHT, FRONT KF-1860
223-00244 LEG EXTENSION LEVER KPS-1850
219-00610 MOUNT, PEC DEC KF-2060
223-00955 PEC DEC ARM, LEFT KF-1860
223-00954 PEC DEC ARM, RIGHT KF-1860
219-00272 PEC DEC HANDLE BAR KPS-1850/1550
219-00265 FOAM FRAME W/SHAFT KPS-1850/1550
219-00266 FOAM FRAME W/O SHAFT KPS-1850/1550
219-00612 SUPPORT, SEAT PAD (PEC DEC) KF-2060
219-00613 BRACKET, BACK PAD ADJ (PEC DEC) KF-2060
223-01090 FRAME, RIGHT LEG HOLD LEG KF-2060
223-01091 FRAME, LEFT LEG HOLD LEG KF-2060
219-00274 PULLEY BRACKET BLOCK KPS-1850
219-00275 PULLEY BRACKET KPS-1850
219-00273 PULLEY BRACKET W/SHAFT KPS-1850
230-00008 LONG FOAM TUBE, 219-00070
223-01083 PRESS ARM, KF-2060
206-00490 PLUG, 40X80 KF-2060
2
9
206-00394 PLUG, 50.8X76.2 KF SERIES
206-00391 SQUARE PLUG, 50.8 KF SERIES
206-00491 PLUG, 44.5 KF-2060
7
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
10
4
206-00492 PLUG, 25X50 KF-2060
8
202-00143 SCREW, M8*6
3
202-00727 SCREW, BUTTON HD SOCKET CAP M8X15
206-00026 WEIGHT BUMPER KPS
9
4
100 206-00153 RUBBER MAT KPS-2050
1
101 202-00678 WASHER, CHROME 38X11X2
102 202-00145 BIG WASHER, 56.5*10.5*5
103 202-00122 PHILLIP SCREW, M4*20
9
2
2
104 202-00016 BRONZE ID 25.4
8
105 202-00023 BRONZE BUSHING, ID 12.2
106 206-00131 PLASTIC BUTTON
6
14
3
107 202-00675 CAP, ALUMINUM 32
108 206-00138 ROUND PLUG 25
2
109 206-00136 RUBBER STOPPER
2
110 229-00053 LAT CABLE KPS-2050 P110
111 229-00054 LOW ROW/ABDOMINAL CABLE KPS-2050 P111
112 229-00050 PEC DEC CABLE KPS-2050/1850
113 229-00049 LEG PRESS CABLE SUBSTITUTE KPS-2050/1850
114 229-00056 SHORT CHEST CABLE KPS-2050
115 229-00056 SHORT CHEST CABLE KPS-2050
116 229-00038 LONG CHAIN 12
1
1
1
1
1
1
1
117 202-00137 WASHER, 9*22*2
7
118 202-00134 SPRING WASHER 8
1
119 202-00100 SPRING WASHER, M10
17
2
223-00011 RIGHT SQUAT ARM KPS-2000 #35
223-00010 LEFT SQUAT ARM KPS-2000 #34
230-00021 PRESS STATION SHAFT KPS-2050/2000
219-00034 BENCH BACK PAD ADJ. FRAME KPS-2000
219-00288 FOAM BRACKET KPS-2050
223-00959 WEIGHT SHROUD, BOTTOM KF-1860
223-01094 SHROUD, WEIGHT B KF-2060
223-00092 LAT BAR KPS-GYM, 223-00574
223-00099 SHORT BAR
120 202-00141 BRONZE BUSHING, ID16
121 202-00140 LONG PULLEY SPACER
6
122 202-00025 SHORT PULLEY SPACER - KPS
123 202-00071 LONG PULLEY SPACER - KPS GYMS
124 210-00093 CABLE ADAPTOR
2
8
1
125 202-00127 WASHER, 13*24*1.5
25
13
2
126 202-00092 NYLON NUT, M12
127 202-00664 SCREW, BUTTON HEAD SOCKET CAP M10X50
128 202-00662 SCREW, BUTTON HEAD SOCKET CAP M10X25
129 202-00130 WASHER, BIG 11*38*2
12
8
210-00097 ADJUSTABLE STOPPER, KPS
219-00281 CABLE RETAINER KPS-1850/2050
223-00247 GUIDE ROD KPS-1850
130 202-00685 SCREW, BUTTON HD SOCKET CAP M12X90
131 202-00657 SCREW, BUTTON HEAD SOCKET CAP M12X80
132 202-00639 SCREW, M12X125 BUTTON HEAD SOCKET CAP
133 202-00726 SCREW, BUTTON HD SOCKET CAP M10X105
134 202-00700 SCREW, BUTTON HD SOCKET CAP M10X85
135 202-00634 SCREW, M10X80 BUTTON HEAD SOCKET CAP
136 202-00647 BUTTON HEAD SOCKET CAP SCREW M10X75
137 202-00637 SCREW, M10X70 BUTTON HEAD SOCKET CAP
138 202-00665 SCREW, BUTTON HEAD SOCKET CAP M10X65
139 202-00716 SCREW, BUTTON HD SOCKET CAP M10X60
140 202-00674 SCREW, 10-32X3.2
4
4
228-00248 PAD, SEAT (BENCH) KF-2060
228-00247 PAD, UPPER BACK KF-2060
228-00219 SEAT PAD, KF-1860
4
2
6
228-00218 BACK PAD, KF-1860
7
223-00031 TOP PLATE KPS-GYM
12
11
7
210-00004 WEIGHT PIN
223-00228 BIG PULLEY 4.5"
206-00395 FOAM PADDING, 100X22X180 KF SERIES
210-00029 POP PIN LOCKING
1
6
210-00099 AB STRAP KPS-2050/1850/1550
210-00061 HAND STRAP INRAY GYM
210-00059 ANKLE STRAP INRAY GYM
206-00103 LAT BAR GRIP - KPS
141 202-00658 SCREW, BUTTON HEAD SOCKET CAP M10X45
142 202-00635 SCREW, M10X30 BUTTON HEAD SOCKET CAP
143 202-00128 WASHER, 11*20*2
12
4
128
52
2
144 202-00091 NYLON NUT, M10
219-00616 BAR, BENCH SEAT PAD ADJ KF-2060
206-00467 BALL HEAD, KF-OB
145 223-00957 WEIGHT SHROUD,TOP KF-1860
146 202-00132 HEX KEY 6
1
202-00156 SPRING, 1.5*13*43, KPS-2050
202-00149 SPRING, 1*13*38, KPS-2050
202-00157 PIN SHAFT, KPS-2050
147 202-00133 HEX KEY 4
1
148 210-00094 LUBE
1
150 219-00276 SELECTOR ROD INRAY-GYMS
151 202-00212 SCREW BOLT, M12*35
2
206-00146 PIN KNOB KPS-2050
2
206-00148 NYLON SPACER KPS-2050
206-00052 SMALL GRIPS
152 202-00129 REGULAR HEX NUT 10
1
153 206-00392 FOOT CAP, RIGHT 50.8 KF SERIES
154 202-00636 SCREW, M8X25 BUTTON HEAD SOCKET CAP
155 202-00224 WASHER, 9X16X1.6
4
206-00053 LONG GRIPS KPS-2000
8
210-00001 SAFETY PIN KPS
8
210-00262 POP PIN, PRESS ARM KF-2060
202-00030 PILLOW BLOCK BEARING (BLACK)
206-00143 PEC DEC STOP BUMPER KPS-2050
202-00024 BEARING ID 25
156 228-00246 PAD, LOWER BACK KF-2060
157 223-00958 WEIGHT SHROUD, MIDDLE KF-1860
158 202-00677 SMALL SPACER, KF-1860
159 202-00676 SCREW, BUTTON HD SOC CAP M6X18
160 202-00227 WASHER, 6.6X12X1.6
1
2
16
16
32
1
206-00150 CASTER BLACK KPS-2050
206-00393 FOOT CAP, LEFT 50.8 KF SERIES
206-00061 BASE PAD KPS
161 202-00703 HEX KEY 5
162 202-00696 HEX KEY 8
1
206-00099 END CAP BUMPER - KPS
163 202-00728 HEX KEY 3/32"
1
202-00147 U PIN
#
#
202-00730 BOLT PACK, KF-2060 (1)
202-00731 BOLT PACK, KF-2060 (2)
1
202-00155 SPRING, 1*8*35
1
202-00142 NUT, M6
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Warranty Information
KEYS FITNESS PRODUCTS, L.P.
LIFETIME WARRANTY
This Warranty applies in the United States and Canada to products manufactured or distrib-
uted by Keys Fitness Products, LP (“Keys”) under the KEYS brand name. The warranty is non-
transferable and valid only to the original purchaser.
Keys warrants that the Product you have purchased for non-commercial, personal, family, or
household use from Keys or from an authorized Keys reseller is free from defects in materi-
als or workmanship under normal use during the warranty period. Your sales receipt, showing
the date of purchase of the Product, is your proof of purchase. This warranty only extends
to you, the original purchaser. It is not transferable to anyone who subsequently purchases
or acquires the Product from you. This Warranty becomes VALID ONLY if the product is pur-
chased through a Keys Fitness authorized dealer unless otherwise authorized by Keys Fitness in writing and must be
assembled / installed according to the instructions included with the Product.
In a light institutional setting, Keys will extend a one year limited warranty to the original purchaser.
During the warranty period Keys will repair or replace (at Keys' option) the product if it becomes defective, malfunc-
tions, or otherwise fails to conform with this Warranty under normal use. In repairing the Product, Keys may replace
defective parts with new or, at the option of Keys, serviceable used parts that are equivalent to new parts in per-
formance. All exchanged parts and Products replaced under this warranty will become the property of Keys. Keys
reserves the right to change manufacturers of any part to cover any existing warranty.
This warranty DOES NOT COVER shipping charges, export taxes, custom duties and taxes, or any other charges
associated with transportation of the parts or Product. To obtain warranty service, you must contact a Keys autho-
rized retailer, service technician or Keys Fitness at our phone number located in this manual. Any parts determined
to be defective must be returned to Keys to obtain warranty service. You must prepay any shipping charges, export
taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product. In addi-
tion, you are responsible for insuring any parts or Product shipped or returned. You assume the risk of loss during
shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence
of alteration, erasure or forgery of proof-of-purchase documents will be cause to void this Warranty.
This Warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This
Limited Warranty does not extend to any Product that has been damaged or rendered defective; (a) as a result of
accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Keys; (c) by modification of the
Product : (d) operation on incorrect power supplies; or (e) as a result of service by anyone other than Keys, or an
authorized Keys warranty service provider. Product on which the serial number has been defaced or removed is not
eligible for warranty service. Should any Product submitted for warranty service be found ineligible, an estimate
of repair cost will be furnished and the repair will be made if requested by you upon Keys' receipt of payment or
acceptable arrangements for payment.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER
KEYS NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY
NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that
may vary from state to state. This is the only express warranty applicable to Keys-branded products. Keys neither
assumes nor authorizes anyone to assume for it any other express warranty.
(10) DAYS OF PURCHASE TO REGISTER YOUR UNIT WITH KEYS FITNESS PRODUCTS, LP. MAIL WARRANTY CARD
TO: KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Keys Fitness Products, L.P.
4009 Distribution Drive, Suite 250
Garland, Texas 75041
Customer Service: 1-888-380-0482
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Indesit Refrigerator TA5 TA5S User Manual
Infinity Speaker System QPS1 User Manual
InFocus Saw F C J 65V User Manual
Intel Security Camera NSC2U User Manual
Juniper Networks Network Router MX240 User Manual
JVC TV VCR Combo HR VCD1 User Manual
KitchenAid Clothes Dryer KEYE760W User Manual
KitchenAid Toaster KMTT400BW0 User Manual
Klipsch Speaker RF 10 User Manual
Krell Industries CD Player KPS 25sc User Manual