Kenwood Stereo Receiver KRF V5300D User Manual
AUDIO VIDEO CONTROL CENTER  
KRF-V5300D  
INSTRUCTION MANUAL  
Declaration of Conformity with regard to the  
EMC Directive 2004/108/EC  
Manufacturer:  
Kenwood Corporation  
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan  
EU Representative's:  
Kenwood Electronics Europe BV  
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands  
© B60-5738-00/00 (EW/XW)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY INSTRUCTIONS  
Caution : Read this page carefully to ensure safe operation.  
Read Instructions – All the safety and operating instructions  
should be read before the product is operated.  
Retain Instructions – The safety and operating instructions should  
be retained for future reference.  
12.Servicing – Do not attempt to service this product yourself  
as opening or removing covers may expose you to dangerous  
voltage or other hazards. Refer all servicing to qualified service  
personnel.  
Heed Warnings – All warnings on the product and in the operating  
instructions should be adhered to.  
Follow Instructions – All operating and use instructions should be  
followed.  
13.Damage Requiring Service – Unplug this product from the  
wall outlet and refer servicing to qualified service personnel  
under the following conditions:  
a) When the power-supply cord or plug is damaged,  
b) If liquid has been spilled, or objects have fallen into the  
product,  
c) If the product has been exposed to rain or water,  
d) If the product does not operate normally by following the  
operating instructions.  
1. Cleaning – Unplug this product from the wall outlet before  
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a  
damp cloth for cleaning.  
2. Attachments – Do not use attachments not recommended by  
the product manufacturer as they may cause hazards.  
e) If the product has been dropped or damaged in any way, and  
f) When the product exhibits a distinct change in performance  
– this indicates a need for service.  
3. Water and Moisture – This product shall not be exposed to  
dripping and splashing – for example, near a bath tub, wash  
bowl, kitchen sink, or laundry tub; in a wet basement; or near a  
swimming pool; and the like. Do not place an object containing  
liquid, such as a flower vase, on the appliance.  
g) If an abnormal smell or smoke is detected.  
14.Replacement Parts – When replacement parts are required, be  
sure the service technician has used replacement parts specified by  
the manufacturer or have the same characteristics as the original  
part. Unauthorized substitutions may result in fire, electric shock, or  
other hazards.  
4. Accessories – Do not place this product on an  
unstable cart, stand, tripod, bracket, or table. The  
product may fall, causing serious injury to a child  
or adult, and serious damage to the product.  
15.Safety Check – Upon completion of any service or repairs to  
this product, ask the service technician to perform safety checks  
to determine that the product is in proper operating condition.  
Use only with a cart, stand, tripod, bracket, or  
table recommended by the manufacturer. Any mounting of  
the product should follow the manufacturer’s instructions,  
and should use a mounting accessory recommended by the  
manufacturer. A product and cart combination should be moved  
with care. Quick stops, excessive force, and uneven surfaces may  
cause the product and cart combination to overturn.  
16.Wall or Ceiling Mounting – This product should be mounted  
to a wall or ceiling only as recommended by the manufacturer.  
17.Heat – This product should be situated away from heat sources  
such as radiators, heat registers, stoves, or other products that  
produce heat. Do not place a flaming object, such as a candle  
or lantern, or near the product.  
5. Ventilation – Slots and openings in the cabinet are provided for  
ventilation and to ensure reliable operation of the product and  
to protect it from overheating, and these openings must not be  
blocked or covered. The openings should never be blocked by  
placing the product on a bed, sofa, rug, or other similar surface.  
This product should not be placed in a built-in installation such  
as a bookcase or rack unless proper ventilation is provided or  
the manufacturer’s instructions have been adhered to.  
18.Power Lines – An outside antenna system should not be  
located in the vicinity of overhead power lines or other electric  
light or power circuits, or where it can fall into such power lines  
or circuits. When installing an outside antenna system, extreme  
care should be taken to keep from touching such power lines or  
circuits as contact with them might be fatal.  
6. Power Sources – This product should be operated only from the  
type of power source indicated on the product. If you are not sure of  
the type of power supply to your home, consult your product dealer  
or local power company.  
19.Outdoor Antenna Grounding – If an outside antenna or cable  
system is connected to the product, be sure the antenna or  
cable system is grounded so as to provide some protection  
against voltage surges and built-up static charges. Article  
810 of the National Electrical Code, ANSI/NFPA 70, provides  
information with regard to proper grounding of the mast  
and supporting structure, grounding of the lead-in wire to an  
antenna discharge unit, size of grounding conductors, location  
of antenna-discharge unit, connection to grounding electrodes,  
and requirements for the grounding electrode.  
CAUTION– Polarization –  
7.  
This product may be equipped  
with a polarized alternating-current line plug (a plug having one  
blade wider than the other). This plug will fit into the power outlet  
only one way. This is a safety feature. If you are unable to insert the  
plug fully into the outlet, try reversing the plug. If the plug should  
still fail to fit, contact your electrician to replace your obsolete  
outlet. Do not defeat the safety purpose of the polarized plug.  
8. Power Cord Protection – Power-supply cords should be routed  
so that they are not likely to be walked on or pinched by items  
placed upon or against them, paying particular attention to  
cords at plugs, convenience receptacles, and the point where  
they exit from the product.  
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD IN WIR  
E
GROUND CLAMPS  
ANTENNA  
9. Lightning – For added protection for this product during a  
lightning storm, or when it is left unattended and unused  
for long periods of time, unplug it from the wall outlet and  
disconnect the antenna or cable system. This will prevent  
damage to the product due to lightning and power-line surges.  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRIC SERVICE  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMP  
EQUIPMENT  
POWER SERVICE GROUNDING  
10.Overloading – Do not overload wall outlets, extension cords,  
or integral convenience receptacles as this can result in a risk of  
fire or electric shock.  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
NEC – NATIONAL ELECTRICAL CODE  
11.Object and Liquid Entry – Never push objects of any kind into  
this product through openings as they may touch dangerous  
voltage points or short-out parts that could result in a fire or  
electric shock. Never spill liquid of any kind on the product.  
Notes:  
1. Item 7 is not required except for grounded or polarized equipment.  
2. Item 19 complies with UL in the U.S.A.  
English  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before applying power  
Further adjustments .......................................... 32  
Contents  
Fine adjustment of the sound ......................................... 32  
To ensure safety, read the items carrying  
this marking carefully.  
Additional functions .......................................... 34  
Convenient functions ......................................................... 34  
Remote control operations for Kenwood DVD  
players ................................................................. 35  
Troubleshooting ................................................. 36  
Specifications...................................................... 38  
Before applying power ................................... 2  
Safety precautions...........................................................2  
Unpacking..................................................................................2  
Notes on instructions.............................................................2  
IMPORTANT SAFETY INSTRUCTIONS ............. 3  
Special features........................................................................4  
Special features  
Names and functions of parts ............................. 5  
Main unit ....................................................................................5  
Remote control unit ...............................................................6  
Preparing the remote control.............................................7  
PURE AUDIO MODE¡  
This is the mode for enjoying audio sources in high-quality stereo.  
It shuts off the power to the video circuitry as well as the display  
to eliminate their influence on the audio circuitry and improve  
the reproduced audio quality.  
Setting up the system .......................................... 8  
Speaker placement.................................................................8  
Digital connections ................................................................9  
Connecting a DVD player (6-channel input) .............. 10  
Connecting audio components...................................... 11  
Connecting video components...................................... 12  
Connecting video components  
True home theater sound£  
This unit incorporates a wide variety of surround modes to bring  
you maximum enjoyment from your video software. Select a  
surround mode according to your equipment or the software you  
are going to play and enjoy!  
(COMPONENT VIDEO) (For Australia) ................... 13  
Connecting the speakers................................................... 14  
Connecting the antennas.................................................. 15  
Connecting to the AV AUX jacks..................................... 15  
• Dolby Digital  
• Dolby Pro Logic II  
Speaker settings ................................................. 16  
Speaker setup (Easy Setup) .............................................. 16  
Speaker setting flow ........................................................... 17  
Getting into the setup mode........................................... 17  
Speaker setup ("SP SETUP").............................................. 18  
Adjusting the speaker level ("TEST TONE") ................. 18  
Distance setting ("DISTANCE")......................................... 19  
Low frequency effects level ("LFE LVL") ........................ 19  
• DTS  
• DSP surround modes  
• DVD 6-channel input  
Normal Playback................................................. 20  
Preparing for playback ....................................................... 20  
Listening to a source component .................................. 21  
Listening to music with PURE AUDIO MODE.............. 21  
Adjusting the sound............................................................ 22  
Ambience effects ................................................ 23  
Surround modes................................................................... 23  
Surround play........................................................................ 25  
DVD 6-channel playback................................................... 26  
Listening to radio broadcasts............................ 27  
Tuning (non-RDS) radio stations .................................... 27  
Using RDS (Radio Data System) ..................................... 27  
RDS Auto Memory ............................................................... 28  
Presetting radio stations manually................................ 28  
Receiving preset stations .................................................. 29  
Receiving preset stations in order (P.CALL)................. 29  
Tuning by Program TYpe (PTY search) ......................... 30  
Using the RDS DISP. (display) key ................................... 30  
Recording ............................................................ 31  
Recording mode setting in digital audio source  
recording (main unit only)....................................... 31  
Recording audio (analog sources) ................................. 31  
Recording video.................................................................... 31  
KRF-V5300D  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Names and functions of parts  
Main unit  
Frequency display,  
Input display,  
AUTO DETECT indicator  
Preset channel display,  
DIGITAL indicator  
Band indicators  
AUTO indicator  
RDS indicator  
PTY indicator  
Surround mode display  
DSP MODE  
indicator  
Speaker indicator  
CLIP indicator  
MUTE  
indicator  
TONE indicator  
6CH INPUT indicator  
DTS indicator  
DOLBY DIGITAL  
indicator  
TUNED indicator  
PRO LOGIC  
indicator  
ST. indicator  
Input channel status indicator  
Display  
VOLUME CONTROL  
DOLBY DIGITAL  
DTS  
ACTIVE EQ  
PURE AUDIO MODE  
SPEAKERS ON/OFF  
MULTI CONTROL  
INPUT SELECTOR  
AV AUX  
VIDEO  
PURE AUDIO MODE  
LISTEN MODE  
SETUP  
BAND  
AUTO/MONO ACTIVE EQ INPUT MODE  
L-AUDIO-R  
PHONES  
8 SETUP key  
&
^ AV AUX key  
1
(power) key  
Use to select the speakers' settings  
Use to select AV AUX source.  
& AV AUX jack  
Standby indicator  
etc.  
Switch the unit ON and standby.  
When the unit is in standby mode, the  
standby indicator is lit.  
9 MULTI CONTROL knob  
Use to connect a device such as a  
camcorder and a game player.  
Use to control a variety of settings.  
0 BAND key  
2 Surround LED indicators  
DOLBY DIGITAL indicator  
Light when this unit is in the Dolby  
Digital mode.  
Standby mode  
Use to select the broadcast band.  
! AUTO/MONO key  
While the standby indicator is lit, a small  
amount of power is supplied to the system  
to back up the memory. This is called  
standby mode. Under the condition, the  
system can be turned ON by the remote  
control unit.  
Use to select the auto tuning or  
manual tuning mode.  
DTS indicator  
Light when in the DTS mode.  
ACTIVE EQ indicator  
Use to select a recording mode. ⁄  
@ ACTIVE EQ key  
™
Use to select ACTIVE EQ setting.  
# INPUT MODE key  
Light when in the ACTIVE EQ mode.  
3 Remote sensor  
)
Use to switch between full auto,  
digital and analog inputs.  
4 VOLUME CONTROL knob  
5 PHONES jack  
$ INPUT SELECTOR knob  
Use for headphone listening.  
6 SPEAKERS ON/OFF key  
Use to turn the speakers ON/OFF.  
Use to select the input sources.  
% PURE AUDIO MODE key  
PURE AUDIO MODE indicator  
Use to select PURE AUDIO MODE.  
When this mode is on, the PURE  
AUDIO MODE indicator is lit.  
¡
7 LISTEN MODE key  
∞
Use to select the listen mode.  
English  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Names and functions of parts  
Remote control unit  
4 PTY key  
º
Use for PTY search.  
SUBTITLE key  
AUTO MEMORY  
ANGLE  
MEMORY  
REPEAT  
DVD  
RECEIVER  
ACTIVE EQ  
Use to operate the Kenwood DVD player.*  
5 Numeric keys  
RDS DISP.  
AUDIO  
PTY  
SUBTITLE  
Use to call up preset stations.  
Use to operate the Kenwood DVD player.*  
DIMMER  
6 LISTEN MODE key  
Use to select a listen mode.  
7 PURE AUDIO MODE key  
Select PURE AUDIO MODE.  
8 5, ∞, 2, 3 keys  
ENTER key  
∞
BASS BOOST  
TONE  
¡
TOP MENU key  
SOUND  
SETUP  
MENU key  
RETURN key  
ON SCREEN key  
EASY SETUP  
Use to operate the Kenwood DVD player.*  
9 8 key  
Use to operate the Kenwood DVD player.*  
BAND key  
PURE AUDIO  
MODE  
Use to select the broadcast band.  
6 key  
LISTEN MODE  
TOP MENU  
MULTI CONTROL  
Use to operate the Kenwood DVD player.*  
AUTO/MONO key  
MENU  
Use to select the auto tuning or manual tuning mode.  
7 key  
Use to operate the Kenwood DVD player.*  
0 P. C A L L 4/¢ keys  
Use to call preset channel.  
ª
ENTER  
Use to operate the Kenwood DVD player.*  
!
RECEIVER key  
Use to turn this unit on and off.  
DVD key  
Use to turn on the Kenwood DVD player on and off.  
RETURN  
ON SCREEN  
@ ACTIVE EQ key  
™
BAND  
Use to select ACTIVE EQ setting.  
MUTE  
# DIMMER key  
›
Use to adjust the brightness of the display and the indicators.  
$ BASS BOOST key  
™
Use to select the maximum adjustment setting for the low  
frequency range.  
% TONE key  
™
MD/TAPE  
DVD/6CH  
AV AUX  
TUNER  
CD/DVD  
VIDEO 2  
Use to switch the status of TONE control.  
^ SOUND key  
¤
VIDEO 1  
Use to adjust the sound quality and ambience effects.  
& SETUP key  
&
Use to select the speakers' settings.  
* EASY SETUP key  
^
Use to select speaker setting.  
( MULTI CONTROL 5/∞ keys  
Select an setup item.  
1 AUTO MEMORY key  
•
) VOLUME %/fi keys  
Use to adjust volume setting.  
¡ MUTE key  
Use for auto memory of RDS and FM radio stations.  
ANGLE key  
Use to operate the Kenwood DVD player.*  
Use to temporarily mute the sound.  
™ TUNING 1/¡ keys  
Use to select the radio station.  
Use to operate the Kenwood DVD player.*  
£ Input source keys  
2 MEMORY key  
•
Use for manual memory of radio stations.  
REPEAT key  
Use to operate the Kenwood DVD player.*  
3 RDS DISP. key  
Use to display RDS information.  
AUDIO key  
º
Use to select the input source.  
Note:  
Use to operate the Kenwood DVD player.*  
•
* For how to be able to use the keys to operate the Kenwood  
DVD player, see <Remote control operations for Kenwood DVD  
players> fi.  
KRF-V5300D  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Opeerraattiioonn  
Preparing the remote control  
When the Standby indicator is lit, the power turns ON when you  
press [ RECEIVER] on the remote control unit. When the power  
comes ON, press the key you want to operate.  
Loading batttteries  
œ Remove the cover.  
Operating range (Approx.)  
Remote sensor  
Standby indicator  
∑ Insert batteries.  
Infrared ray system  
•
Insert two (R03) batteries following the polarity indications.  
é Close the cover.  
•
When pressing more than one remote control key successively,  
press the keys securely by leaving an interval of 1 second or more  
between keys.  
Notes:  
1. The supplied batteries may have shorter lives than ordinary  
batteries due to use during operation checks.  
2. When the remote-controllable distance gets shorter than before,  
replace both batteries with new ones.  
3. Placing the remote sensor in direct sunlight, or in direct light from  
a high frequency fluorescent lamp may cause a malfunction.  
In such a case, change the location of the system installation to  
prevent malfunction.  
English  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up the system  
Make connections as shown in the following pages.  
Speaker placement  
When connecting the related system components, be sure to  
refer to the instruction manuals supplied with the components  
you are connecting.  
Front speaker  
Front speaker  
Do not connect the power cord to a wall outlet until all  
connections are completed.  
Notes:  
1. Be sure to insert all connection cords securely. If their connections  
are imperfect, the sound may not be produced or there will be  
noise interference.  
Center speaker  
Subwoofer  
2. Be sure to remove the power cord from the AC outlet before  
plugging or unplugging any connection cords. Plugging/  
unplugging connection cords without disconnecting the power  
cord can cause malfunctions and may damage the unit.  
Listening  
position  
Surround speaker  
Surround speaker  
Analog connections  
Audio connections are made using RCA pin cords. These cables  
transfer stereo audio signal in an "analog" form. This means the  
audio signal corresponds to the actual audio of two channels.  
These cables usually have 2 plugs at each end, red for the right  
channel and white for the left channel. These cables are usually  
packed together with the source unit, or are available at your  
local electronics retailer.  
Front speakers:  
Place the left and right speakers at each side of your TV. Angle the  
speakers towards the listening area to enhance the stereo effect.  
Center speaker:  
Place the center speaker on the center between the front left and  
right speakers. Tilt the speaker upward or down-ward so that it is  
directly facing the listening area.  
Microcomputer malfunction  
If operation is not possible or an erroneous display appears,  
even though all connections have been made properly, reset the  
microcomputer by referring to <Troubleshooting>. fl  
Surround speakers:  
Place the surround speakers as high as possible, either directly to  
the sides of the listening area or else slightly behind the listening  
area. Adjust the angles so that these speakers are facing directly  
towards the listeners.  
Subwoofer:  
¤ CAUTION  
The power of this equipment will not be completely cut off  
from the wall outlet when the power switch is turned off.  
Install the equipment so that the wall outlet is easily  
accessible and, in case of emergency, immediately unplug the  
power cord from the wall outlet.  
Usually, place the subwoofer in the front center position in  
the listening room, near one of the front speakers. (Since  
the subwoofer has less directivity than other speakers, it can  
be placed almost in any position that can offer the best low  
frequency reproduction according to the room layout.)  
Note:  
•
Although the ideal surround system consists of all the speakers  
listed above, if you don’t have a center speaker or a subwoofer,  
you can divide those signals between the available speakers in  
the speaker settings steps to obtain the best possible surround  
reproduction from the speakers you have available.  
¤ CAUTION  
Be sure to adhere to the following, or proper ventilation  
will be blocked causing damage or fire hazard.  
•
Leave some space around the unit (from the largest outside  
dimension including projection) equal to or greater than,  
shown below.  
Side panel : 10 cm  
Back panel : 10 cm  
•
This unit is using the cooling fan. Do not place the unit  
onto a bed, a sofa, a carpet, or similar. Sucked-in dust can  
cause fire.  
KRF-V5300D  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Digital connections  
The DIGITAL IN jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or  
standard PCM (CD) format digital signals.  
If you have connected any digital components to this unit, be sure to read the <Selecting the input mode> ) carefully.  
To AC wall outlet  
OPTICAL  
VIDEO2  
COAXIAL  
DVD / 6CH  
OPTICAL  
CD/DVD  
DIGITAL IN  
Optical fiber  
cable  
Optical fiber  
cable  
OPTICAL  
DIGITAL OUT  
(AUDIO)  
CD or DVD player  
Component with DTS,  
Dolby Digital, or PCM  
OPTICAL DIGITAL OUT*  
OPTICAL  
DIGITAL OUT  
(AUDIO)  
Note:  
•
* Connect the video signal and analog audio signals to the VIDEO 2 jacks. (<Connecting video components> @)  
English  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up the system  
Connecting a DVD player (6-channel input)  
If you have connected a DVD player to this unit with digital connection, be sure to read the <Selecting the input mode> ) carefully.  
To AC wall outlet  
VIDEO2  
IN  
CENTER  
OUT  
VIDEO1  
IN  
SUB  
WOOFER  
COAXIAL  
DVD/6CH  
OPTICAL  
CD/DVD  
FRONT
SURROUND  
DIGITAL IN  
DVD / 6CH IN  
DVD  
IN  
MONITOR  
OUT  
VIDEO  
FRONT  
SURROUND  
SUBWOOFER  
OUT  
CENTER  
OUT  
OUT L/R OUT L/R  
COAXIAL DIGITAL  
OUT (AUDIO)  
DVD player  
VIDEO OUT  
(Yellow RCA  
pin cord)  
Note:  
For Australia only  
•
If the DVD player has COMPONENT VIDEO OUT, COMPONENT VIDEO connection is possible. (<Connecting video components (COMPONENT  
VIDEO)> #)  
KRF-V5300D  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting audio components  
To AC wall outlet  
L
R
REC OUT PLAY IN REC OUT PLAY IN  
AUX CD/DVD  
MD /TAPE  
VIDEO 1  
AUDIO  
OUT  
IN  
Casette deck or MD player  
OUT  
CD or DVD player  
Other component  
OUT  
English  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up the system  
Connecting video components  
To AC wall outlet  
VIDEO2  
IN  
VIDEO1  
OUT  
L
VIDEO1  
IN  
R
REC OUT PLAY IN REC OUT PLAY IN  
PLAY IN  
VIDEO 2  
AUX CD/DVD  
MD /TAPE  
VIDEO 1  
DVD  
IN  
VIDEO  
MONITOR  
OUT  
AUDIO  
AUDIO  
OUT  
VIDEO  
OUT  
DVD player  
AUDIO  
OUT  
VIDEO OUT  
VIDEO IN  
Video component with  
recording function  
AUDIO IN  
VIDEO  
IN  
Monitor TV  
Note:  
•
A video component with digital audio outputs should be connected to the VIDEO 2 jacks.  
KRF-V5300D  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting video components (COMPONENT VIDEO) (For Australia)  
To AC wall outlet  
L
CR  
R
CB  
REC OUT PLAY IN REC OUT PLAY IN  
PLAY IN  
VIDEO 2  
AUX CD/DVD  
MD /TAPE  
VIDEO 1  
Y
AUDIO  
MONITOR  
OUT  
VIDEO2  
IN  
VIDEO1  
IN  
DVD  
IN  
COMPONENT VIDEO  
VIDEO OUT  
AUDIO OUT*  
VIDEO  
IN  
DVD player  
Video component with  
recording function  
AUDIO OUT  
VIDEO OUT  
Monitor TV  
Video component  
AUDIO OUT  
VIDEO OUT  
Notes:  
•
•
* If the DVD player has 6 channel output, connecting to DVD/6CH IN jacks is possible. (<Connecting a DVD player (6-channel input)> 0)  
If some of the video equipment are connected to the COMPONENT jacks and the rest are connected to the normal (composite) VIDEO jacks,  
make sure to connect the TV to the MONITOR OUT jacks of both COMPONENT VIDEO and VIDEO.  
•
Depending on the type of TV, it may be necessary to switch the input of the TV according to the type of video input (COMPONENT input or  
COMPOSITE input). Refer to the instruction manual of your TV for more information.  
English  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up the system  
Connecting the speakers  
Powered subwoofer  
Conneccttiinngg tthhee tterminals  
œ Strip coating.  
∑ Push the lever.  
é Insert the cord.  
® Return the lever.  
SUB WOOFER  
PRE OUT  
SURROUND SPEAKERS (6-167)  
FRONT SPEAKERS (6-167)  
SURROUND  
CENTER  
GREEN  
RED  
WHITE  
GRAY  
BLUE  
L
R
L
R
Center speaker  
Left  
Right  
Surround speakers  
Left  
Right  
Front speakers  
Notes:  
•
Speaker impedance  
After confirming the speaker impedance indications printed on the rear panel of the receiver, connect speakers with matching impedance  
ratings. Using speakers with a rated impedance other than that indicated on the rear panel of the receiver could result in malfunctions or  
damage to the speakers or the receiver.  
•
•
Never short circuit the + and – speaker cords.  
If the left and right speakers are connected inversely or the speaker cords are connected with reversed polarity, the sound will be unnatural  
with ambiguous acoustic imaging. Be sure to connect the speakers correctly.  
KRF-V5300D  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the antennas  
The broadcast reception cannot be made unless the antennas are  
connected. Connect the antennas correctly as instructed below.  
AM looopp aanntteenna  
Place the supplied loop antenna as far as possible from the  
receiver, TV set, speaker cords and power cord. Adjust the  
direction for best reception.  
AM  
FM 757  
GND  
œ Attach to the stand.  
Attach to  
the stand  
FM indoor antenna  
∑ Push the lever.  
FM outdoor antenna  
(commercially available)  
é Insert the antenna cord.  
AM loop antenna  
Use an antenna  
adapter  
(commercially  
available)  
® Release the lever.  
Connecting to the AV AUX jacks  
† Place the antenna and adjust the direction.  
FM indooorr aannttenna  
The supplied indoor antenna is for temporary use only. For stable  
signal reception we recommend using an outdoor antenna.  
Disconnect the indoor antenna when you connect one outdoors.  
VIDEO  
L-AUDIO-R  
œ Insert the antenna cord.  
∑ Fix the antenna on the wall.  
FM outddooor annttenna  
Lead the 75Ω coaxial cable connected to the FM outdoor antenna  
into the room and connect it to the FM 75Ω terminal.  
AUDIO OUT  
VIDEO OUT  
Camcorder, game player,  
and etc.  
(commercially available)  
English  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker settings  
® Use [MULTI CONTROL 5/∞] to select your listening  
Speaker setup (Easy Setup)  
position.  
The speaker settings can be completed by simply selecting the  
room type and listening position. The audio will be corrected  
automatically according to the characteristics of the speaker  
system in use.  
FRONT  
CENTER  
REAR  
If more detailed speaker settings are required, use the procedure  
in <Speaker setting flow> &.  
EASY SETUP  
MULTI  
CONTROL ꢀ/O  
† Press [EASY SETUP].  
•
The speakers are set up as shown below.  
Subwoofer :  
ON  
Front speaker:  
Center speaker:  
Average size  
Average size  
Surround speaker: Average size  
Subwoofer re-mix* : ON  
*
The function for adding the bass of other channels to the  
subwoofer channel according to the speaker setup.  
œ Press [EASY SETUP] to enter the easy setup mode.  
Note:  
∑ Use [MULTI CONTROL 5/∞] to select your room  
•
Easy setup with may not be appropriate with certain speaker  
type.  
systems or listening environment. In this case, go through  
<Speaker setup ("SP SETUP")> *.  
5m (16'5-3/8")  
4m (13'1-7/8")  
3m (9'10-3/8")  
12m2  
24m2  
35m2  
SMALL  
MEDIUM  
LARGE  
é Press [EASY SETUP].  
KRF-V5300D  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker setting flow  
Getting into the setup mode  
The detailed settings below allow you to enjoy full performance  
of the receiver according to the environment of your listening  
room.  
The setup procedure is identical for all of the setting elements.  
Once you remember the following procedure, you can easily set  
up other setting elements.  
Speaker settings consist of 4 elements.  
Speaker Setup ("SP SETUP") *  
Select whether each speaker channel is used or, if used, its size.  
The Easy Setup function also allows you to make speaker settings  
easier.  
See <Speaker setup (Easy Setup)> ^.  
SETUP  
MULTI CONTROL  
Test Tone ("TEST TONE") *  
Select the output level from each speaker.  
SETUP  
MULTI CONTROL  
ꢀ/O  
Distance ("DISTANCE") (  
Select the distance between each speaker and the listening  
position.  
Low Frequency Effects Level ("LFE LVL") (  
œ Press [SETUP] to enter the setup mode.  
Select the level of bass audio enhancement.  
∑ Use [MULTI CONTROL 5/∞] to select the element to  
Low Frequency Effect channel delivers separate non-directional  
bass signals to the subwoofer for more dynamic deep bass sound  
effects.  
setup.  
Display  
Selection  
"SP SETUP"  
"TEST TONE"  
"DISTANCE"  
"LFE LVL"  
Speaker setup  
Test tone  
Distance  
Low frequency effects level  
Exit the setup mode.  
Speaker settings completed!  
"EXIT"  
é Press [SETUP] to get into the setup mode of the  
selected element.  
To exit the setup mode  
Select "EXIT" in the step ∑ and press [SETUP].  
English  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker settings  
Speaker setup ("SP SETUP")  
Adjusting the speaker level  
("TEST TONE")  
This sets up the speakers according to the speaker system in  
use. Speaker setup is required every time the speaker system is  
changed.  
From your usual listening position, adjust the volume output of  
each speaker. The output level from each speaker should be the  
same.  
œ See <Getting into the setup mode> (&) and  
select "SP SETUP".  
œ See <Getting into the setup mode> (&) and  
∑ Use [MULTI CONTROL 5/∞] to select the subwoofer  
select "TEST TONE".  
setting.  
∑ Use [MULTI CONTROL 5/∞] to select either "AUTO"  
or "MANUAL".  
Speaker  
Display  
Selection  
"SUBW ON"  
"SUBW OFF"  
With Subwoofer  
Without Subwoofer  
Subwoofer  
Display  
Selection  
The test tone is heard from the speakers one after another with  
2 seconds each.  
"AUTO"  
"MANUAL"  
The test tone is heard from the speaker you have selected.  
é Press [SETUP].  
é Press [SETUP].  
® Adjust the output level.  
If you select "AUTO":  
® Repeat steps ∑ – é for the rest of the speaker  
setting.  
When you hear the test tone from the speaker which  
you wish to adjust, use [MULTI CONTROL 5/∞] and  
adjust the volume of the test tone. When you finish  
adjusting, press [SETUP].  
Speaker  
Display  
Selection  
"FRNT LRG"  
"FRNT NML"  
"CNTR NML"  
"CNTR LRG"  
"CNTR OFF"  
"SURR NML"  
Large size front speaker  
Front speaker  
Average size front speaker  
Average size center speaker  
Large size center speaker  
No center speaker is connected.  
Average size surround speaker  
Large size surround speaker  
No surround speaker is connected.  
Subwoofer re-mix is on.  
If you select "MANUAL":  
Center speaker  
Use [MULTI CONTROL 5/∞] to adjust the volume of  
the test tone and press [SETUP]. You will hear the  
test tone from the next speaker.  
Surround speaker "SURR LRG"  
"SURR OFF"  
"RMX ON"  
Subwoofer re-mix*  
"RMX OFF"  
Subwoofer re-mix is off.  
† Go to the next setting, "DISTANCE".  
•
If you wish to exit the setup mode, see <To exit the setup mode>  
&.  
*
The function for adding the bass of other channels to the  
subwoofer channel according to the speaker setup.  
† Go to the next setting, "TEST TONE".  
•
If you wish to exit the setup mode, see <To exit the setup mode>  
&.  
Notes:  
•
When "SUBW OFF" is selected, the front speakers are  
automatically set to "FRNT LRG".  
•
For "FRNT LRG" selection, no sound will be heard from subwoofer  
even it is set to ON. However, if you select "RMX ON", you will be  
able to hear sound from the subwoofer.  
•
•
•
When in STEREO mode, the sound goes directly to front speakers.  
If "FRNT NML" is selected, "CNTR LRG" cannot be selected.  
If "CNTR NML" or "CNTR OFF" is selected, "SURR LRG" cannot be  
selected.  
KRF-V5300D  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Distance setting ("DISTANCE")  
Low frequency effects level  
("LFE LVL")  
This sets the distance from each speaker to the listening position.  
œ Measure the distance from the listening position to  
Low frequency effect signal is used exclusively for giving the field  
effect of bass tone in the Dolby Digital and DTS signal.  
each speaker and jot down in the table below.  
œ See <Getting into the setup mode> (&) and  
Distance from the listening  
position  
Speaker  
Indicator  
select "LFE LVL".  
Front speaker (left)  
Center speaker  
Front speaker (right)  
Surround speaker (right)  
Surround speaker (left)  
Subwoofer  
"L"  
"C"  
"R"  
"RS"  
"LS"  
"SW"  
feet (meters)  
feet (meters)  
feet (meters)  
feet (meters)  
feet (meters)  
feet (meters)  
∑ Use [MULTI CONTROL 5/∞] to adjust the low  
frequency effect level.  
•
The level is adjusted from 0dB to -10dB in 1dB step decrements.  
∑ See <Getting into the setup mode> (&) and  
é Press [SETUP].  
select "DISTANCE".  
é Use [MULTI CONTROL 5/∞] to select the distance  
to the front speaker.  
Adjustment will start from front left speaker.  
•
The setup is complete when the "EXIT" indication appears.  
•
® Press [SETUP] to exit the setup mode.  
Indicator  
® Press [SETUP].  
† Repeat steps é – ® to input the distance for the  
rest of the speaker.  
¥ Go to the next setting, "LFE LVL".  
•
If you wish to exit the setup mode, see <To exit the setup mode>  
&.  
English  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Normal Playback  
Seleccttiinngg the input mmoode (maiinn uunnit onlyy))  
If you have selected a component connected to the DIGITAL IN  
jacks (CD/DVD, VIDEO2 and DVD/6CH INPUT), make sure that the  
input mode setting is correct for the type of audio signal to be  
used.  
Preparing for playback  
Some preparatory steps are needed before starting playback.  
INPUT SELECTOR  
œ Use [INPUT SELECTOR] to select "CD/DVD",  
"VIDEO2", or "DVD/6CH".  
∑ Press [INPUT MODE].  
Each press switches the setting as follows:  
INPUT MODE  
LISTEN MODE  
Display  
"F-AUTO"*1  
"D-MANUAL"  
"6CH INPT"*2*3 6ch input  
"ANALOG"*3  
Setting  
Input signal  
SPEAKERS  
RECEIVER  
ON/OFF  
Full Auto  
Digital Manual  
Digital input or Analog input  
Digital input  
DVD/6CH input  
Analog input  
Analog input  
LISTEN MODE  
1
*
Factory setting.  
2
*
"6CH INPT" setting can be switched only when the input selector  
is set to "DVD/6CH".  
3
*
This cannot be selected when in DTS play mode.  
Full Auto ("F-AUTO"):  
The unit detects the digital or analog input signal  
automatically. The unit selects the input mode and  
listen mode automatically during playback to match the  
type of input signal (Dolby Digital, DTS or PCM) and the  
speaker setting. Normally use Full Auto.  
Input source keys  
In this mode, "AUTO DETECT" indicator lights up.  
"DIGITAL" indicator also lights up when digital input  
Turniinngg oonn tthhee ppoowweerr  
œ Turn on the power to the related components.  
signal comes in.  
"AUTO DETECT" and "DIGITAL" indicators  
∑ Press [ RECEIVER] to turn on the receiver unit.  
Setting the sppeeaaker sttaatus (maiinn uunnit onlyy))  
Digital Manual ("D-MANUAL"):  
Some discs produce sound skipping even when "F-  
AUTO" is set. Select "D-MANUAL" with such a disc. Digital  
Manual accelerates the input signal processing by fixing  
the listen mode and therefore minimizes sound skipping  
during disc playback.  
Press [SPEAKERS ON/OFF] to switch the speaker on  
or off.  
The speaker indicator lights up when set to on.  
If audio reproduction stops in the middle due to change  
in the input signal, press [LISTEN MODE].  
6ch input ("6CH INPT"):  
Select this setting to play the DVD player connected to  
DVD/6CH IN jacks.  
Note:  
•
Set Speakers to OFF for stereo playback. When Speakers is set to  
ON again, the listen mode remains in stereo if the input signal is  
digital.  
Analog input ("ANALOG"):  
Select this setting to play analog signals from a cassette  
deck, VCR, or record player.  
Note:  
•
If [INPUT MODE] is pressed too quickly, sound may not be  
produced. Press [INPUT MODE] again.  
KRF-V5300D  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to a source component  
Listening to music with PURE  
AUDIO MODE  
VOLUME CONTROL  
The PURE AUDIO MODE allows you to enjoy music sources in  
high-quality stereo.  
INPUT SELECTOR AV AUX  
PURE AUDIO MODE  
PURE AUDIO MODE  
VOLUME ꢁ/o  
Input source keys  
œ Select the music source you want to listen to.  
∑ Start playback from the selected source.  
é Press [PURE AUDIO MODE].  
œ Select the source you want to listen to.  
When using the remote control unit:  
Use the Input source keys to select a source.  
The following input source keys are prepared on the  
remote control unit:  
•
While in PURE AUDIO MODE, the listen mode is set to stereo.  
The display will be turned off and PURE AUDIO MODE indicator  
lights up.  
•
•
•
•
•
•
•
•
•
Tuner (FM/AM broadcast reception)  
PURE AUDIO MODE indicator  
"CD/DVD"  
"MD/TAPE"  
"VIDEO1"  
"VIDEO2"  
"DVD/6CH"  
"AUX"  
PURE AUDIO MODE  
PURE AUDIO MODE  
"AV AUX"  
When using the main unit:  
Use [INPUT SELECTOR] to select a source.  
The input sources change as shown below with [INPUT  
SELECTOR]:  
1Tuner (FM/AM broadcast reception)  
2"CD/DVD"  
To cancel  
3"MD/TAPE"  
Press [PURE AUDIO MODE] again.  
4"VIDEO1"  
•
PURE AUDIO MODE is also cancelled when listen mode is  
changed. See <Surround play>. ∞  
5"VIDEO2"  
6"DVD/6CH"  
7"AUX"  
Notes:  
•
"AV AUX" can be selected with [AV AUX].  
•
When the input mode is "6CH INPT", the listen mode does not  
change. (<Selecting the input mode> ))  
∑ Start playback from the selected source.  
é Use [VOLUME %/fi] to adjust the volume.  
•
•
During PURE AUDIO MODE, no video signal is output.  
When the PURE AUDIO MODE is canceled, the listen mode  
remains in stereo if the input signal is digital.  
English  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Normal Playback  
Onnee--ttouch loww ffrreequenncy emphaassis (Bass  
Boooosstt)) ((rreemmootte contrrooll oonnlly)  
Adjusting the sound  
You can adjust the sound quality when this unit is in the PCM  
stereo and analog stereo modes.  
Press [BASS BOOST].  
•
Press the key once to select the maximum (+10) low frequency  
emphasis setting.  
MULTI CONTROL ACTIVE EQ  
•
•
TONE will automatically be turned ON.  
This key does not function when this unit is in the sound quality  
or ambience effects adjustment mode.  
When the ACTIVE EQ mode is set to ON, set it to OFF and then  
control the BASS BOOST setting.  
ACTIVE EQ  
BASS BOOST  
TONE  
•
To cancel  
Press [BASS BOOST] again.  
MULTI CONTROL  
ꢀ/O  
Muting the souund (remootee ccoonnttrrooll oonnlly)  
Press [MUTE] to mute the sound of the speakers.  
"MUTE" indicator blinks.  
MUTE  
Adjustinng the Tone (remotee ccoonnttrrooll oonnlly)  
You can adjust the sound quality when this unit is in the PCM  
stereo and analog stereo mode.  
To cancel  
Press [MUTE] again so that the "MUTE" indicator goes  
off.  
œ Press [TONE] to select the Tone mode.  
•
MUTE can also be deactivated by adjusting volume.  
∑ Use [MULTI CONTROL 5/∞] to select "TONE ON" or  
"TONE OFF".  
ACTIVE EQ mmoode  
You can enjoy a more impressive sound effect when ACTIVE EQ is  
turned ON during Dolby Digital and DTS playback and, when in  
PCM and analog stereo mode.  
Press [ACTIVE EQ] for the following selections;  
é When in "TONE ON" selection, press [TONE] for the  
following displays.  
Display  
Setting  
"ACTIVE EQ MUSIC"  
"ACTIVE EQ CINEMA"  
"ACTIVE EQ GAME"  
"ACTIVE EQ OFF"  
Effective when listening to music.  
Effective when watching a movie.  
Effective when playing a game.  
Active EQ function is off.  
Display  
Setting  
Range  
"BASS"  
"TREB"  
Adjusts low frequency range.  
Adjusts high frequency range.  
-10 – +10 (in 2 step)  
-10 – +10 (in 2 step)  
•
ACTIVE EQ function will not be available when REC MODE, AUTO  
TUNING or PRESET MEMORY is ON and during 96kHz LPCM  
® Use [MULTI CONTROL 5/∞] to adjust the sound  
quality.  
playback.  
ACTIVE EQ indicator lights up.  
•
When the ACTIVE EQ mode is set to ON, set it to OFF and then  
control the TONE setting.  
ACTIVE EQ  
† Press [TONE].  
KRF-V5300D  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ambience effects  
Dolby Digital  
Surround modes  
Dolby Digital is a highly sophisticated and versatile audio  
encoding/decoding technology. Dolby Digital technology can  
transmit mono, stereo (two-channel), or up to 5.1-channel  
surround sound (discrete* multichannel audio).  
In 5.1-channel surround sound, the three front channels  
(Left/Center/Right) deliver crisp, clean dialogue and accurate  
placement of on-screen sounds, while twin surround channels  
(Left Surround/Right Surround) wrap around the audience and  
immerse them in the action. The LFE (Low-Frequency Effects)  
channel delivers real impact for explosions and other effects that  
can, literally, be felt as well as heard.  
This unit is equipped with listen modes that allow you to enjoy an  
enhanced sonic ambience with a variety of video sources.  
In order to obtain the optimum effect from the surround modes,  
make sure to input the proper speaker settings beforehand.  
See <Speaker settings> ^.  
The below speaker placements are for 5.1 channel  
surround sound system which are;  
•
•
•
•
•
Dolby Digital  
Dolby Pro Logic II  
DTS  
The superior coding efficiency of Dolby Digital-and its ability  
to deliver high-quality discrete multichannel audio without  
compromising video quality has made it the designated audio  
standard for DVD worldwide.  
DSP mode  
DVD 6-channel  
* The sound information contained in each of the six available  
channels is distinct and independent. These six channels  
are described as a "5.1-channel" system, because there are  
five full-bandwidth channels with 3 Hz to 20 kHz frequency  
range for Front Left and Right, Center, and Surround, plus one  
"Low Frequency Effects" (LFE) subwoofer channel devoted to  
frequencies from 3 to 120 Hz.  
TV / SCREEN  
SW  
C
Dolby Pro Logic II  
Dolby® Pro Logic® II technology processes any high quality stereo  
(two-channel) movie and music audio into five playback channels  
of full-bandwidth surround sound. A matrix surround decoding  
technology, Dolby Pro Logic II detects the directional cues that  
occur naturally in stereo content and uses these elements to  
create a five-channel surround sound playback experience.  
Dolby Pro Logic II is fully compatible with all Dolby Pro Logic  
technologies. It provides optimal audio for playback in a 5.1-  
channel home theater system for the thousands of videocassettes  
and TV programs encoded in four-channel Dolby Surround (the  
encoding counterpart to Dolby Pro Logic's decoding technology).  
(Dolby Pro Logic II surround Movie mode)  
SL  
SR  
Dolby Pro Logic II also enables video game consoles to encode  
five-channel surround sound information into a stereo signal  
with virtually no impact on the console's CPU, which means all  
this extra audio won't slow your game down. (Dolby Pro Logic II  
surround Game mode)  
Dolby Pro Logic II can bring new life to your CD collection. Play  
your music through your home theater system, and you'll hear  
seamless, natural sound with new depth and detail. It's almost  
like hearing a newly remastered CD. (Dolby Pro Logic II surround  
Music mode)  
L :  
Front Left speaker  
SW : Subwoofer  
C :  
R :  
LS : Surround Left speaker  
RS : Surround Right speaker  
Center speaker  
Front Right speaker  
Manufactured under license from Dolby Laboratories. Dolby,  
Pro Logic, and the double-D symbol are trademarks of Dolby  
Laboratories.  
Manufactured under license under U.S. Patent #’s: 5,451,942;  
5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and  
worldwide patents issued & pending. DTS and DTS Digital  
Surround are registered trademarks and the DTS logos and  
Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All  
Rights Reserved.  
English  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ambience effects  
DTS  
DTS Digital Surround is the standard for providing 5.1 channels  
of discrete digital audio in consumer electronics products and  
software content.  
Abboouutt iinnddiiccaattoorrss for surroundd mmoode  
DTS can contain a larger volume of data than Dolby Digital, and  
can reproduce high quality surround sound. They are the same  
as the Dolby Digital 5.1 channels, but it is a format that lowered  
the audio compression rate when recording digitally. Because of  
that, rich sound with high S/N can be reproduced. Moreover, an  
exact, magnificent surround sound with wide dynamic range and  
excelling in separation is a feature of DTS.  
Input channel status indicators  
Surround mode indicators  
Input channel status indicator  
It shows the channels contained in the input signal. Note that the  
input channel indicator does not show the channel of the listen  
mode.  
DTS has a ".1" or LFE channel.  
The indication "LFE" appears in the display when a signal is being  
input for this channel.  
The "LFE" indicator lights when the low frequency effects level is  
adjusted. See <Low frequency effects level ("LFE LVL")> (().  
The "S" indicator lights when the surround component consists of  
a single channel.  
DSP mode  
The DSP mode lets you add the atmosphere of a live concert  
or hall to almost any type of program source. These modes are  
particularly effective when used with stereo program sources, like  
CD, television, and FM radio. You might enjoy trying the ARENA,  
JAZZ CLUB, THEATER, STADIUM or DISCO mode the next time you  
watch a concert or sporting event!  
Surround mode indicator  
The indicator for the selected listen mode lights up. "DIGITAL" also  
lights when the input signal is digital.  
What's DSP?  
DSP stands for Digital Signal Processor.  
The way a sound is heard in an actual environment depends  
on a variety of different factors. One of the most important is  
reverberation (the act of decaying elements of sound echoing in  
various places).  
The DSP modes produce the feeling of presence by using the DSP  
to create reverberation, without spoiling the sound quality of the  
original signal.  
DVD 6-channel mode  
Using a DVD player or the like equipped with six (5.1) output  
channels and this unit, you can enjoy multi-channel encoded  
DVD source material in all its splendor. Since the source signals  
are digital and each channel is input independently, the resulting  
sound quality, sense of spaciousness, and dynamic range are  
superb.  
The indication "6CH INPUT" appears in the display during DVD  
6-channel mode selection.  
Note:  
•
LFE = Low Frequency Effects.  
This channel delivers separate non-directional bass signals to the  
subwoofer for more dynamic deep bass sound effects.  
KRF-V5300D  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When "Dolby Digital" is selected:  
Surround play  
Select the listen mode according to the source being played back.  
"DOLBY DIGITAL" will scroll from right to left.  
When the DTS signal is input:  
Display  
Listen mode  
Indicator  
"DTS"  
"STEREO"  
DTS 5.1 channel surround mode  
Stereo mode  
"DTS"  
"DTS"  
LISTEN MODE  
VOLUME CONTROL  
When "DTS" is selected:  
When the analog signal or digital signal (except for  
Dolby Digital or DTS signal) is input:  
LISTEN MODE  
VOLUME ꢁ/o  
Display  
Listen mode  
Indicator  
"PL II MOVIE"  
"PL II MUSIC"  
"PL II GAME"  
"PRO LOGIC"  
"ARENA"  
"JAZZ CLUB"  
"THEATER"  
"STADIUM"  
"DISCO"  
Pro Logic II surround Movie mode  
Pro Logic II surround Music mode  
Pro Logic II surround Game mode  
Pro Logic mode  
DSP surround ARENA mode  
DSP surround JAZZ CLUB mode  
DSP surround THEATER mode  
DSP surround STADIUM mode  
DSP surround DISCO mode  
Stereo mode  
"PRO LOGIC"  
"PRO LOGIC"  
"PRO LOGIC"  
"PRO LOGIC"  
"DSP MODE"  
"DSP MODE"  
"DSP MODE"  
"DSP MODE"  
"DSP MODE"  
––  
Preparations  
•
•
•
Turn on the related components.  
Complete <Speaker settings>. ^  
Select the source you wish to play back with  
surround sound.  
Select the input mode (analog or digital) for  
the source you wish to playback. (Noise may be  
produced when a DTS source is played by selecting  
the analog input.) )  
•
"STEREO"  
é Adjust the volume.  
œ Start playing the video software.  
Notes:  
∑ Press [LISTEN MODE] to select the listen mode.  
•
•
•
Depending on the type of the signal or speaker setting, some  
listen modes cannot be selected.  
When playback is started, the sound may be cut or interrupted  
before the input source is confirmed as Dolby Digital.  
To enjoy Dolby Digital surround (as well as all the other listen  
modes) from a single component, be sure to use a Dolby Digital  
compatible source component.  
The listen mode settings are stored separately for  
each input. If the input mode is set to full auto ("AUTO  
DETECT" lights), the unit selects the optimal listen mode  
automatically based on the type of input signal and the  
speaker settings.  
•
Dolby Digital or DTS signal having more channels than the  
maximum number of playback channels available using this unit’s  
current settings is input, downmixing is performed to match the  
number of available channels.  
Each press of [LISTEN MODE] switches the setting as  
listed.  
When the Dolby Digital signal is input:  
Display  
Listen mode  
Indicator  
"DOLBY DIGITAL" Dolby Digital surround mode  
"DOLBY DIGITAL"  
"DOLBY DIGITAL"  
and "PRO LOGIC"  
"DOLBY DIGITAL"  
and "PRO LOGIC"  
"DOLBY DIGITAL"  
and "PRO LOGIC"  
"PL II MOVIE"*  
"PL II MUSIC"*  
"PL II GAME"*  
Pro Logic II surround Movie mode  
Pro Logic II surround Music mode  
Pro Logic II surround Game mode  
"DOLBY DIGITAL"  
and "PRO LOGIC"  
"DOLBY DIGITAL"  
"PRO LOGIC"*  
"STEREO"  
Pro Logic mode  
Stereo mode  
*
Available when the input signal has only 2 channels.  
English  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ambience effects  
96kHzz LLPPCCMM ppllaayybbaack  
This unit is compatible with the 96kHz LPCM playback. To play a  
96kHz DVD, set the listen mode to "STEREO".  
DVD 6-channel playback  
Using a DVD player or the like equipped with six (5.1) output  
channels and this unit, you can enjoy surround sound playback.  
Connecting a DVD player which can decode the surround signal  
itself is also acceptable.  
•
•
In "F-AUTO" input mode, the listen mode will automatically be  
STEREO.  
When in "D-MANUAL" input mode (listen mode is not STEREO),  
"FS 96kHz" will appear in the display and no sound can be heard  
from the speakers.  
INPUT SELECTOR  
Press [LISTEN MODE] (the listen mode changes to the "STEREO"  
mode) to output sound from the speakers.  
INPUT MODE VOLUME CONTROL  
VOLUME ꢁ/o  
DVD/6CH  
Preparations  
•
Connect your DVD player to the DVD/6CH INPUT  
jacks of this unit.  
•
•
Turn on all other components that will be used.  
Complete <Speaker settings>.  
œ Select "DVD/6CH" as the input source.  
∑ Press [INPUT MODE] to select "6CH INPT".  
é Start playback of a DVD disc.  
® Adjust the volume.  
Notes:  
•
It is not possible to adjust the speaker level or sound effect  
([SETUP], [SOUND], [LISTEN MODE], [ACTIVE EQ] and [TONE] will  
not be functional) of the channels separately when this unit is in  
the 6CH INPUT mode. Adjust the speaker level with the controls  
of the DVD player. Refer to the Instruction manual of the DVD  
players for the detailed operating instructions.  
•
For the powered subwoofer, you can adjust the volume of the  
subwoofer using the subwoofer’s own volume control.  
KRF-V5300D  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to radio broadcasts  
This unit can store up to 40 stations in the memory and recall  
Using RDS (Radio Data System)  
them by one-touch operation.  
Radio stations can be classified into RDS (Radio Data System)  
stations and other stations. To listen to or store RDS stations in  
the preset memory see <Using RDS (Radio Data System)>.  
RDS is a system that transmits useful information (in the form of  
digital data) for FM broadcasts along with the broadcast signal.  
Tuners and receivers designed for RDS reception can extract  
the information from the broadcast signal for use with various  
functions, such as automatic display of the station name.  
Tuning (non-RDS) radio stations  
Before using a function utilizing the RDS, be sure to  
perform the RDS Auto Memory operation by referring to  
the description in <RDS Auto Memory>.(•)  
BAND  
AUTO/MONO  
RDS functions:  
RDS AUTO MEMORY function  
Automatically selects and stores up to 40 RDS stations in  
the preset memory.  
If fewer than 40 RDS stations have been stored in the  
preset memory, regular FM stations will be stored in the  
remaining places.  
MULTI CONTROL  
INPUT SELECTOR  
PS (Program Service) Name Display  
Automatically displays the station name transmitted by  
the RDS station.  
PTY (Program TYpe) identification Search  
MULTI CONTROL  
ꢀ/O  
Automatically tunes to a station that is currently  
broadcasting the specified program type (genre).  
RT (Radio Text) function  
BAND  
AUTO/MONO  
Displays the radio text data transmitted by some RDS  
stations when you press [RDS DISP.]. There is "NO RT" or  
"RT ----" display if no text data is transmitted.  
The "RDS" indicator lights up when an RDS broadcast  
(signal) is received.  
TUNER  
œ Use [TUNER] to select the tuner.  
∑ Use [BAND] to select the desired broadcast band.  
Each press switches the band as follows:  
1FM  
2AM  
Note:  
•
Some functions and function names may differ for certain  
countries and areas.  
é Use [AUTO/MONO] to select the desired tuning  
method.  
Each press switches the tuning method as follows:  
Selection  
Operation  
Indicator  
Auto tuning  
Manual tuning  
The next station is tuned automatically.  
Select a station manually.  
"AUTO" lit  
"AUTO" not lit  
•
Normally, set to "AUTO" (auto tuning). If the radio waves are weak  
and there is a lot of interference, switch to manual tuning. (With  
manual tuning, stereo broadcasts will be received in monaural.)  
® Use [MULTI CONTROL 5/∞] or [TUNING 1/¡] to  
select the station.  
"ST." lights when a broadcast is being received in stereo.  
English  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to radio broadcasts  
RDS Auto Memory  
Presetting radio stations  
manually  
This function automatically stores up to 40 RDS stations in the  
preset memory. In order to use the PTY function, the RDS stations  
must be stored in the preset memory using the RDS AUTO  
MEMORY function.  
The RDS auto memory function assigns preset numbers to RDS  
stations starting from preset number "1". Therefore, be sure  
to execute the RDS auto memory function before using the  
following operations to manually store AM stations and other FM  
stations, and RDS stations.  
AUTO MEMORY  
See <RDS Auto Memory>.  
MEMORY  
MULTI CONTROL  
ꢀ/O  
BAND  
TUNER  
œ Use [TUNER] to select the tuner.  
∑ Use [BAND] to set the broadcast band to "FM".  
é Press [AUTO MEMORY].  
œ Tune to the station you want to store.  
∑ Press [MEMORY] while receiving the station.  
Proceed to step é within 20 seconds.  
(If more than 20 seconds elapse, press [MEMORY] again.)  
•
•
After a few minutes, up to 40 RDS stations are preset in order from  
channel "01".  
Stations already stored in the preset memory may be replaced by  
RDS stations. (i.e., If the RDS AUTO MEMORY function detects 15  
RDS stations, the stations currently preset at numbers 01–15 will  
be replaced by the RDS stations.)  
é Use [MULTI CONTROL 5/∞] to select one of the  
station presets (1 – 40).  
® Press [MEMORY] again to confirm the setting.  
Repeat steps œ, ∑, é, and ® to store as many stations as  
necessary.  
If you store a station at a previously used preset, the previous  
station will be replaced by the new one.  
•
•
KRF-V5300D  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Receiving preset stations  
Receiving preset stations in order  
(P.CALL)  
Numeric  
keys  
P.CALL  
ꢂ/D  
TUNER  
TUNER  
œ Press [TUNER] to select tuner as the source.  
œ Press [TUNER] to select tuner as the source.  
∑ Enter the number of the preset station you want to  
receive (up to "40" preset numbers).  
∑ Use [P.CALL 4/¢] to select the desired station.  
Press the Numeric keys in the following order:  
For "15" : press [+10], [5]  
For "20" : press [+10], [+10], [0]  
Each time you press the key, another preset station is  
received in order.  
•
Holding down the [P.CALL ¢/4], lets you skip through the  
•
If you make a mistake entering a two digit number, press [+10]  
repeatedly to return to the original display and start again.  
presets, receiving each preset station at 0.5 second intervals.  
Preset number  
English  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to radio broadcasts  
é Press [PTY] to start searching.  
Tuning by Program TYpe  
(PTY search)  
Example: Searching for a Rock Music broadcast.  
Display while searching.  
Blinks  
This function lets you set the tuner to automatically search for  
stations which are currently broadcasting the type of program  
(genre) you want to listen to.  
Program type name display  
Under certain receiving conditions, it may take more than 1  
minute to complete the search.  
Display when a station is received.  
Goes out  
PTY  
Station name display  
•
•
No sound is heard while "PTY" is blinking.  
If the desired program type cannot be found, "NO PROG" is  
displayed, then after several seconds the display returns to the  
original display.  
MULTI CONTROL  
ꢀ/O  
To select another program type  
Repeat steps œ, ∑ and é.  
TUNING  
ꢃ/Y  
Using the RDS DISP. (display) key  
Preparations  
RDS DISP.  
•
•
•
Execute the RDS auto memory procedure.  
Set the broadcast band to FM.  
Tune to an RDS station.  
œ Press [PTY] to activate the PTY search mode.  
Pressing [RDS DISP.] changes the contents of the  
display.  
Each press switches the display mode as follows:  
1PS (Program Service) name display  
2RT (Radio Text) display  
When an RDS broadcast is received, the program type is  
shown on the display. If no PTY data is available, or if the  
station is not an RDS station, "NONE" is displayed.  
3Frequency display  
∑ While the "PTY" indicator is lit, use [MULTI  
CONTROL 5/∞] or [TUNING 1/¡] to select the  
program type of your choice.  
1 PS (Program Service) name display:  
The station name is displayed automatically when an RDS  
broadcast is received.  
If no PS data was sent, "NO PS" is displayed.  
Program type  
Pop Music  
Rock Music  
Easy Music  
Light Classical Music  
Serious Classical Music "CLASSICS"  
Other Music  
News  
Display  
Program type  
Weather  
Finance  
Children's Program  
Social Affairs  
Religion  
Display  
"POP M"  
"ROCK M"  
"EASY M"  
"LIGHT M"  
"WEATHER"  
"FINANCE"  
"CHILDREN"  
"SOCIAL"  
"RELIGION"  
"PHONE IN"  
"TRAVEL"  
2 RT (Radio Text) display:  
Text data accompanying the RDS broadcast scrolls across the  
"OTHER M"  
"NEWS"  
Phone In  
Travel  
display. "NO RT" or "RT  
----" is displayed if the current RDS  
station does not provide RT data.  
Current Affairs  
Information  
Sport  
Education  
Drama  
Culture  
Science  
Varied Speech  
"AFFAIRS"  
"INFO"  
"SPORT"  
"EDUCATE"  
"DRAMA"  
"CULTURE"  
"SCIENCE"  
"VARIED"  
Leisure  
"LEISURE"  
"JAZZ"  
"COUNTRY"  
"NATION M"  
"OLDIES"  
Jazz Music  
Country Music  
National Music  
Oldies Music  
Folk Music  
Documentary  
3 Frequency display:  
Displays the frequency of the current station.  
"FOLK M"  
"DOCUMENT"  
KRF-V5300D  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording  
® Start playback, then start recording.  
Recording mode setting in digital  
audio source recording  
(main unit only)  
•
If the audio reproduction stops in the middle due to change in  
the input signals, etc., press [AUTO/MONO].  
Recording audio (analog sources)  
When recording a multi-channel digital audio source, it is  
recommended to set up the recording mode properly to convert  
the digital input into the 2-channel analog output. Usually use  
the "A-REC" (Auto record) mode.  
However, some discs often produce sound skipping. The "M-REC"  
(Manual record) mode should be used with such a disc.  
INPUT SELECTOR  
œ Use [INPUT SELECTOR] to select the source (other  
than "MD/TAPE") you want to record.  
AUTO/MONO INPUT SELECTOR  
∑ Set the MD or TAPE recorder to record.  
é Start playback, then start recording.  
œ Use [INPUT SELECTOR] to select the source (CD/  
DVD, DVD/6CH or VIDEO2) you want to record.  
∑ Set the MD or TAPE recorder to record.  
Recording video  
é Press and hold [AUTO/MONO] for more than 2  
seconds to select a recording mode during digital  
input.  
Recording mode  
Display  
Operation  
Recording mode off  
---  
The digital input record mode is switched off.  
The digital input signals (DTS, Dolby Digital  
or PCM) are identified automatically and  
converted into stereo signals that are ready  
for recording.  
The input signal type at the moment this  
mode is selected is held throughout this  
mode.  
INPUT SELECTOR  
Auto record mode  
"A-REC"  
"M-REC"  
œ Use [INPUT SELECTOR] to select the video source  
(other than "VIDEO1") you want to record.  
Manual record mode  
∑ Set the video deck connected to VIDEO 1 to record.  
Select the REC MODE to record a digital input source. See  
<Recording mode setting in digital audio source recording>.  
•
When the "M-REC" mode is selected, the digital input signal is  
converted to stereo signals (down-mix). But once the digital  
signal is changed to other signal, no signal is output.  
•
•
•
When the "A-REC" mode is selected, the digital input signal is  
converted to stereo signals even if the digital signal is changed.  
When the digital mode changes during recording in the "A-REC"  
mode, the audio input source may be interrupted momentarily.  
é Start playback, then start recording.  
•
Recording may not be normal for some video software. This is  
due to the copy guard condition.  
For "A-REC" mode:  
For "M-REC" mode:  
English  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Further adjustments  
Sppeeaakkeerr lleevveell aaddjjuustment  
Fine adjustment of the sound  
The output level from the desired speaker channels can be fine  
adjusted according to the properties of each disc.  
The adjustment is only temporary for the current input selection.  
The value will return automatically to the original setup value  
when the power is turned on/off or when the input selection is  
changed.  
You can make further adjustments to the sound while listening to  
playback in the surround mode.  
SPEAKERS ON/OFF  
œ Press [SOUND] repeatedly until the speaker to be  
adjusted appears on the display. ("C", "RS", "LS", or  
"SW")  
MULTI CONTROL  
∑ Use the [MULTI CONTROL 5/∞] to adjust the level.  
Input levveell aaddjjuussttmmeenntt ((aanalloogg sources  
only)  
If the input level of an analog source signal is too high, the CLIP  
indicator will blink to indicate. Adjust the input level.  
SOUND  
MULTI CONTROL  
ꢀ/O  
œ Press [SOUND] repeatedly until "INPUT" appears  
on the display.  
∑ Use the [MULTI CONTROL 5/∞] to adjust the level.  
œ Press [SOUND] until the desired item appears on  
the display.  
Each time you press the key, the menu changes as  
follows. Note that some items are not displayed  
depending on speaker settings and listen mode.  
Midnightt mmoode (Dolbby Diiggiittal anndd DDTTSS  
modde only)  
Display  
Adjustment  
Range  
"C"  
"RS"  
"LS"  
Center speaker level *1  
Surround right speaker level *1  
Surround left speaker level *1  
Subwoofer level *1  
-10 – +10dB  
-10 – +10dB  
-10 – +10dB  
-10 – +10dB  
-6, -3, 0  
When watching movies at night, you might not be able to raise  
the volume as loud as normal. Midnight mode compresses the  
dynamic range of previously specified heavy sound passage of  
the Dolby Digital and DTS mode sound track (like scenes with  
sudden increases in volume) to minimize the difference in volume  
between the scenes with heavy sound passage and scenes with  
normal sound passage. This makes it easy to hear all of the sound  
track, even when listening at low volumes.  
"SW"  
"INPUT"  
"NIGHT"  
"PANORAMA"  
"DIMENSION"  
Input level *2  
Midnight mode *3  
Panorama mode *4  
Dimension *4  
"ON", "OFF"  
"ON", "OFF"  
œ Press [SOUND] repeatedly until "NIGHT" appears  
"CENTER WIDTH" Center width *4  
on the display.  
Input source name Exit the adjustment mode.  
This can be selected only if "CD/DVD", "DVD/6CH" or  
"VIDEO2" is selected as the source and the listen mode  
is set to "DOLBY DIGITAL" or "DTS".  
1
*
The adjustment is only temporary for the current input selection.  
The value will return automatically to the original setup value  
when the power is turned on/off or when the input selection is  
changed.  
∑ Use [MULTI CONTROL 5/∞] to select the "ON" or  
"OFF" setting.  
2
3
4
*
*
*
Analog mode only  
Dolby Digital and DTS mode only  
Pro Logic II Music mode only  
∑ Use the [MULTI CONTROL 5/∞] to adjust the  
setting as desired.  
•
Some Dolby Digital or DTS software may not be compatible with  
the Midnight mode.  
KRF-V5300D  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Panorammaa mmooddee ((PPrroo LLooggiicc IIII Muusic moddee  
only)  
When listening to music, you will be able to enjoy the  
"wraparound" sound effect when you adjust the panorama mode.  
Centeerr WWiiddtthh mmoode (Prroo LLooggiicc IIII MMuussiicc  
modde only)  
Center Width adjustment allows you to enjoy an enhanced  
sound when listening to music through center image from only  
center speaker, or left and right speakers or various combinations  
adjustments.  
œ Press [SOUND] repeatedly until "PANORAMA"  
appears on the display.  
œ Press [SOUND] repeatedly until "CENTER WIDTH"  
•
The "PANORAMA" setting indication scrolls across the display.  
appears on the display.  
•
The "CENTER WIDTH" indication scrolls across the display.  
∑ Use [MULTI CONTROL 5/∞] to adjust the left-  
"PANORAMA" will be scrolled from right to left.  
center-right output.  
Center image will be heard from Center speaker only.  
∑ Use [MULTI CONTROL 5/∞] to select the "ON" or  
"OFF" setting.  
1"ON" : PANORAMA mode is ON.  
2"OFF" : PANORAMA mode is OFF.  
Center image will be heard from Left and Right  
speakers only.  
Diimmeensioon moddee ((PPro Logic II Musiicc mmoode  
only)  
When listening to music with certain recordings, you will also  
be able to achieve a suitable balance from all the speakers by  
adjusting the dimension mode.  
•
•
When in other positions, center image from Center speaker, Left  
and Right speakers can be heard simultaneously with various  
combinations.  
When the center speaker is switched OFF, this mode will not be  
effective.  
œ Press [SOUND] repeatedly until "DIMENSION"  
appears on the display.  
•
The "DIMENSION" indication scrolls across the display.  
∑ Use [MULTI CONTROL 5/∞] to adjust the  
soundfield towards the rear or the front.  
Soundfield is adjusted towards the front.  
Soundfield is in neutral position.  
Soundfield is adjusted towards the rear.  
English  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional functions  
Listeenniinngg wwiitthh hheeaaddpphhoonneess ((mmaain unit  
only)  
Convenient functions  
œ Press [SPEAKERS ON/OFF] so that the speaker  
indicator goes off.  
Make sure the "SP" indicator is turned off.  
VOLUME CONTROL  
SPEAKERS ON/OFF  
•
If you turn off all of the speakers when in surround mode, the  
surround mode will be canceled as well, resulting in stereo  
playback.  
DIMMER  
∑ Connect headphones to the PHONES jack.  
VOLUME  
ꢁ/o  
PHONES  
Diissppllaayy ddiimmmeer adjuusstment  
The dimmer function lets you select the brightness of the display  
and indicators of this unit. You might find this useful if you darken  
your room to watch movies or listen to music.  
Press [DIMMER].  
é Use [VOLUME %/fi] to adjust the volume.  
The brightness of the display changes among the three  
available settings. Select the brightness level you find  
most pleasing.  
•
The brightness of the LED indicators changes in 2 levels.  
KRF-V5300D  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control operations for Kenwood DVD players  
The remote control of this unit can control Kenwood DVD players directly without using the remote control supplied with the DVD player.  
DV-4900, DV-4070B, DV-2070, DV-203, DVF-9010, DVF-K7010, DVF-5010, DVF-R9030, DVF-R7030, DVF-3530, DV-402, DV-5900, DV-5700,  
DVF-R9050, DVF-J6050, DV-505, DV-503, DV-502, DVF-3550, DVF-3050, DVF-R4050, DVF-605, DV-6050, DVF-R5060,  
DVF-3060, DVF-3060K, DV-705, DVF-R5070, DVF-3070, DVF-3080, DVF-N7080, DVF-8100, DVF-3200, DVF-3250, DVF-3300, DVF-3400,  
DVF-5400, DVF-3500 and DVF-5500.  
How to operate the DVD player with the remote control  
œ Press [ DVD] to turn the DVD player on.  
∑ Press [CD/DVD] or [DVD/6CH] to operate the functions of the DVD player.  
é Press each key for DVD player operation. Refer to the operation manual of the DVD players for the detailed  
operating instructions.  
(To return to the receiver operation mode, press other Input source key.)  
DVD player operation keys  
You can perform these basic operations using the keys described below when connected to Kenwood DVD player.  
REPEAT  
ANGLE  
DVD  
AUTO MEMORY MEMORY  
ANGLE  
REPEAT  
DVD  
RECEIVER  
ACTIVE EQ  
RDS DISP.  
AUDIO  
PTY  
SUBTITLE  
DIMMER  
AUDIO  
SUBTITLE  
BASS BOOST  
TONE  
Numeric keys  
SOUND  
SETUP  
EASY SETUP  
PURE AUDIO  
MODE  
LISTEN MODE  
TOP MENU  
MULTI CONTROL  
TOP MENU  
ENTER  
MENU  
MENU  
ꢁ(Cursor ^)  
o(Cursor ])  
ꢈ(Cursor ,)  
ꢉ(Cursor ?)  
ENTER  
ON SCREEN  
RETURN  
ON SCREEN  
RETURN  
BAND  
ꢇ (Pause)  
ꢅ (ꢆ Play)  
ꢄ (Stop)  
MUTE  
ꢃ (Search)  
Y (Search)  
ꢂ (Skip)  
D (Skip)  
MD/TAPE  
DVD/6CH  
AV AUX  
TUNER  
CD/DVD  
VIDEO 2  
VIDEO 1  
English  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Troubles are not always due to malfunction or failure of the system. In case of a trouble, check the following tables before calling for  
service.  
Amplifier  
Symptom  
Cause  
Remedy  
No sound from the speakers.  
The speaker cords are disconnected.  
Connect it properly referring to <Connecting the  
speakers>.  
$
VOLUME is set to the minimum position.  
MUTE is ON.  
Adjust the volume to a proper level.  
Turn OFF the MUTE.  
™
)
The SPEAKERS switches are set to OFF.  
Speaker cords are short-circuited.  
Set the SPEAKERS switch to ON.  
The standby indicator blinks and sound is not output.  
Sound is not output from one of the speakers.  
Turn the power off, eliminate the short-circuiting, then  
turn on the power again.  
There may be an internal defect.  
If the standby indicator still blinks after eliminating the  
short-circuiting, there may be an internal defect. Switch it  
off, unplug the power cord and call for service.  
The speaker cord is disconnected.  
The speaker is not set up correctly.  
Connect it properly referring to <Connecting the  
speakers>.  
$
Set it up properly referring to <Speaker settings>.  
^
Sound is not output from the surround  
speakers and/or the center speaker, or their sound is  
very soft.  
The surround speaker cords and/or the center speaker  
cord is disconnected.  
Connect it properly referring to <Connecting the  
speakers>.  
$
The speaker is not set up correctly.  
Set it up properly referring to <Speaker settings>.  
^
A surround mode has not been activated.  
Select a surround mode.  
∞
*
The surround and/or center volume controls are set to the  
minimum level.  
Adjust the speaker levels using the test tone.  
When playing a Dolby Digital source signal using a DVD There are many possible causes for this problem,  
player, the sound is cut off soon after it starts. depending on the type of DVD player used.  
Set the input mode to digital manual before starting  
playback of the Dolby Digital source.  
)
No sound is produced during playback from a DVD player. The input mode is set to digital manual.  
Press the [INPUT MODE] key to select to full auto mode.  
)
A video source cannot be recorded normally.  
No video output.  
The software is copy-guarded.  
PURE AUDIO MODE is on.  
PURE AUDIO MODE is on.  
Copy-guarded video software cannot be recorded.  
Turn off the PURE AUDIO MODE.  
¡
Display is turned off.  
While the PURE AUDIO MODE is on, the display is turned  
off.  
¡
Tuner  
Symptom  
Cause  
Remedy  
Radio stations cannot be received.  
No antenna is connected.  
Connect an antenna.  
%
The broadcast band is not set properly.  
The frequency of the desired station is not tuned.  
Noise due to ignition of an automobile.  
Noise due to interference from an electric appliance.  
Noise due to a nearby TV set.  
Set the broadcast band properly.  
Tune the frequency of the desired station.  
Interference  
Install the outdoor antenna away from the road.  
Turn off the power to the appliance.  
Install the unit farther away from the TV.  
A station which was preset cannot be received by pressing The preset station belongs to a frequency that cannot be  
Preset a station with a receivable frequency.  
•
the corresponding numeric key.  
received.  
The preset memory was cleared because the power cord  
had been unplugged for a long period of time.  
Preset the station again.  
•
KRF-V5300D  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control unit  
Symptom  
Cause  
Remedy  
Remote control operation is not possible.  
The remote control is set to the DVD player operation  
mode.  
Press any of the Input Source keys to select the  
appropriate operation mode.  
Batteries are exhausted.  
Replace with new batteries.  
The remote control unit is too far away from the main  
system, controlling angle is too large, or there is an  
obstacle between this unit and the remote.  
Operate the remote control unit within the controllable  
range.  
7
The remote control has not been changed to the operation Press the [CD/DVD] or [DVD/6CH] key to activate the  
mode for the Kenwood DVD player you wish to control.  
operation mode for the component you want to control  
before operation.  
In regaard too ccoonnttaacctt cclleeaaner  
Resetting the Microoccoommppuutter  
Do not use contact cleaners because it could cause a malfunction.  
Be specially careful not to use contact cleaners containing oil, for  
they may deform the plastic component.  
The microcomputer may malfunction (unit cannot be operated,  
or shows an erroneous display) if the power cord is unplugged  
while the power is ON, or due to some other external factor.  
If this happens, execute the following procedure to reset the  
microcomputer and return the unit to its normal operating  
condition.  
Maiinnttenannccee ooff tthhee unit  
When the front panel or case becomes dirty, wipe with a soft, dry  
cloth. Do not use thinner, benzine, alcohol, etc. for these agents  
may cause discoloration.  
While holding down [ ] key on the unit, unplug the  
power cord and plug it back in.  
•
Please note that resetting the microcomputer will clear the  
contents of the memory and return the unit to the state it was in  
when it left the factory.  
Memory backk up function  
Please note that the following items will be deleted from the  
unit's memory if the power cord is disconnected from the AC  
outlet for approximately 1 day.  
• Input selector settings  
• Volume level  
• BASS, TREBLE, INPUT level  
• TONE ON/OFF  
• ACTIVE EQ mode  
• Dimmer level  
• Speaker settings  
• Sound Adjustment (Input level, Midnight  
mode, Panorama mode, Dimension mode,  
Center Width mode)  
• Listen mode setting  
• Tuner setting  
English  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
AUDIO section  
Rated output power during STEREO operation  
(63 Hz – 12.5 kHz, 0.7% T.H.D., at 6 Ω).............100 W + 100 W  
Effective output power during STEREO operation  
RMS (1 kHz, 10% T.H.D., at 6 Ω) ......................... 120 W + 120 W  
Effective power output during SURROUND operation  
FRONT  
(1 kHz, 0.7 % T.H.D. at 6 Ω one channel driven)100 W + 100 W  
(1 kHz, 10 % T.H.D. at 6 Ω one channel driven) 120 W + 120 W  
CENTER  
(1 kHz, 0.7 % T.H.D. at 6 Ω one channel driven) ..............100 W  
(1 kHz, 10 % T.H.D. at 6 Ω one channel driven) ...............120 W  
SURROUND  
(1 kHz, 0.7 % T.H.D. at 6 Ω one channel driven)100 W + 100 W  
(1 kHz, 10 % T.H.D. at 6 Ω one channel driven) 120 W + 120 W  
Total harmonic distortion .............................0.05 % (1 kHz, 50 W, 6 Ω)  
Frequency response (IHF’66)  
CD/DVD.....................................20 Hz – 70 kHz, +0 dB – –3.0 dB  
Signal to noise ratio (IHF’66)  
CD/DVD..............................................................................100 dB  
Input sensitivity / impedance  
VIDEO section  
VIDEO inputs / impedance  
VIDEO (composite) ..............................................1 Vp-p / 75 Ω  
VIDEO outputs / impedance  
VIDEO (composite) ..............................................1 Vp-p / 75 Ω  
COMPONENT VIDEO inputs/ impedance (For Australia)  
COMPONENT VIDEO (Y-signal) ...........................1 Vp-p / 75 Ω  
COMPONENT VIDEO (CB/ CR-signal) ...............0.7 Vp-p / 75 Ω  
COMPONENT VIDEO outputs/ impedance (For Australia)  
COMPONENT VIDEO (Y-signal) ...........................1 Vp-p / 75 Ω  
COMPONENT VIDEO (CB/ CR-signal) ...............0.7 Vp-p / 75 Ω  
FM tuner section  
Tuning frequency range.......................... 87.5 MHz – 108.0 MHz  
Usable sensitivity (DIN at 75 Ω)  
MONO .................. 1.3 μV / 13.2 dBf (40 kHz DEV., S/N 26 dB)  
STEREO ................. 45 μV / 42.1 dBf (46 kHz DEV., S/N 46 dB)  
Total harmonic distortion (DIN at 1 kHz)  
MONO .................................................... 0.2% (71.2 dBf input)  
STEREO .................................................. 0.8% (71.2 dBf input)  
Signal to noise ratio (DIN weighted at 1 kHz)  
MONO ............................ 65 dB (40 kHz DEV., 71.2 dBf input)  
STEREO ........................... 60 dB (46 kHz DEV., 71.2 dBf input)  
Stereo separation (DIN 1 kHz) ............................................36 dB  
Selectivity (DIN 300 kHz) .................................................64 dB  
Frequency response (30 Hz – 15 kHz) .............. +0.5 dB, –3.0 dB  
CD/DVD, AUX, MD/TAPE, VIDEO 1, VIDEO 2 .... 550 mV / 40 kΩ  
AV AUX ................................................................ 550 mV / 50 kΩ  
DVD/6CH INPUT ................................................. 550 mV / 27 kΩ  
Output level / impedance  
REC OUT (MD/TAPE, VIDEO 1)........................... 550 mV / 470 Ω  
PRE OUT (SUBWOOFER) ........................................ 1.5 V / 1.5 kΩ  
Tone control  
BASS ............................................................... 10 dB (at 100 Hz)  
TREBLE ........................................................... 10 dB (at 10 kHz)  
AM tuner section  
Tuning frequency range............................. 531 kHz – 1,602 kHz  
Usable sensitivity (30% mod., S/N 20 dB).... 16 μV / (600 μV/m)  
Signal to noise ratio (30% mod.)  
DIGITAL AUDIO section  
Sampling frequency .................32 kHz, 44.1 kHz, 48 kHz, 96 kHz  
Input level / wave length  
...................................................... 50 dB (60 dBμV EMF input)  
General  
Optical ......................... –15 dBm – –21 dBm / 660 nm 30 nm  
Input level / impedance  
Power consumption ........................................................... 250 W  
Standby power consumption ............................. less than 0.6 W  
Dimensions ...............................................W: 440 mm (17-5/16")  
....................................................................H: 159 mm (6-1/4")  
............................................................... D: 338 mm (13-5/16")  
Weight (net) ......................................................... 8.1 kg (17.9 lb)  
Coaxial...............................................................0.5 Vp-p / 75 Ω  
Notes:  
1. Kenwood follows a policy of continuous advancements in  
development. For this reason specifications may be changed  
without notice.  
2. The full performance may not be exhibited in an extremely cold  
location (under a water-freezing temperature).  
KRF-V5300D  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For your records  
Record the serial number, found on the back of the unit, in the spaces  
designated on the warranty card, and in the space provided below.  
Refer to the model and serial numbers whenever you call upon your  
dealer for information or service on this product.  
Model  
Serial Number  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Oven K6C32 G User Manual
Indesit Washer IWE 81681 User Manual
JBL Speaker JRX212 User Manual
JVC Flat Panel Television LT Z32FX60 User Manual
JVC VCR 0203 AH CR LG User Manual
Kenmore Microwave Oven 87133 User Manual
Kenmore Vacuum Cleaner 3462718579 User Manual
Kenwood Stereo System HM 383MD User Manual
Kodak Printer 1C9753 User Manual
Kompernass TV Antenna KH2329 11 07 V2 User Manual