Kenwood CD Player KDC 4060RA User Manual

CD-RECEIVER

KDC-4060RG

KDC-4060RA

INSTRUCTION MANUAL

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

2WARNING

2CAUTION

To prevent injury and/ or fire, take the

follow ing precautions:

To prevent dam age to the m achine,

take the follow ing precautions:

• Insert the unit all the way until it is fully

locked in place. Otherwise it may fly out of

place during collisions and other jolts.

• Make sure to ground the unit to a negative

12V DC power supply.

• Do not open the top or bottom covers of the

• When extending the ignition, battery or

ground cables, make sure to use automotive-

grade cables or other cables with an area of

0.75mm²(AWG18) or more to prevent cable

deterioration and damage to the cable

coating.

• To prevent short circuits, never put or leave

any metallic objects (e.g., coins or metal

tools) inside the unit.

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not set the removed faceplate or the

faceplate case in areas exposed to direct

sunlight, excessive heat or humidity. Also

avoid places with too much dust or the

possibility of water splashing.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision equipment.

• Be careful not to drop the unit or subject it to

strong shock.

• To prevent deterioration, do not touch the

terminals of the unit or faceplate with your

fingers.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

The unit may break or crack because it

contains glass parts.

• Do not touch the liquid crystal fluid if the LCD

is damaged or broken due to shock. The

liquid crystal fluid may be dangerous to your

health or even fatal.

• To prevent short circuits when replacing a

If the liquid crystal fluid from the LCD

contacts your body or clothing, wash it off

with soap immediately.

fuse, first disconnect the wiring harness.

• During installation, do not use any screws

except for the ones provided. The use of

improper screws might result in damage to

the main unit.

— 3 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

Cleaning the CD Slot

The m arking of products using lasers

(Except for som e areas)

NOTE

As dust can accumulate in the CD slot, clean

it occasionally. Your CDs can get scratched if

you put them in a dusty CD slot.

• If you experience problems during

installation, consult your Kenwood dealer.

• If the unit does not seem to be working right,

try pressing the reset button first. If that does

not solve the problem, consult your Kenwood

dealer.

CLASS 1

LASER PRODUCT

The label is attached to the chassis/case and

says that the component uses laser beams

that have been classified as Class 1. It means

that the unit is utilizing laser beams that are

of a weaker class. There is no danger of

hazardous radiation outside the unit.

AUD

EJECT

PWR

OFF

35Wx4

DISP

SCN

RDM

REP

NAME SET

LOUD

CLK

VOL

ADJ

ATT

Reset button

Lens Fogging

Right after you turn on the car heater in cold

weather, dew or condensation may form on

the lens in the CD player of the unit. Called

lens fogging, CDs may be impossible to play.

In such a situation, remove the disc and wait

for the condensation to evaporate. If the unit

still does not operate normally after a whilst,

consult your Kenwood dealer.

Cleaning the Unit

If the front panel gets dirty, turn off the

power and wipe the panel with a dry silicon

cloth or soft cloth.

2CAUTION

Do not wipe the panel with a stiff cloth or a

cloth dampened by volatile solvents such as

paint thinner and alcohol. They can scratch

the surface of the panel and/or cause the

indicator letters to peel off.

Cleaning the Faceplate Term inals

If the terminals on the unit or faceplate get

dirty, wipe them with a dry, soft cloth.

— 4 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Handling Com pact discs

accessories that can be loaded into the CD

slot, such as stabilisers, protective sheets, or

CD cleaning discs, since they can cause the

unit to malfunction.

Playing a CD that is dirty, scratched

or w arped can cause the sound to

skip and the unit to operate

incorrectly, resulting in w orsened

sound quality. Take the follow ing

precautions to prevent your CDs from

getting scratched or dam aged.

Cleaning CDs

If a CD has become dirty, wipe it off gently

using a commercially available cleaning cloth

or a soft cotton cloth, starting from the

centre of the disc and moving outward. Do

not clean CDs with conventional record

cleaners, anti- static formulas, or chemicals

such as paint thinner or benzene.

Rem oving the CD

Only remove the CD from the machine in a

horizontal direction. You may damage the

surface of the CD if you try pulling it down as

it ejects.

Handling CDs

• Do not touch the recorded side of the CD

(i.e., the side opposite the label) when

holding it.

Checking New CDs for Burrs

When playing a new CD for the first time,

check that there are not any burrs stuck to

the perimeter of the disc or in the central

hole. CDs with burrs stuck on them may not

load properly or may skip whilst playing.

Remove burrs using a ballpoint pen or a

similar utensil.

2CAUTION

• Do not stick tape on either side of the CD.

Do Not Load 8-cm (3-in.) CDs in

the CD slot

If you try to load an 8-cm CD with its adapter

into the unit, the adapter might separate

from the CD and damage the unit.

Tape

Burrs

Do Not Use Special Shape CDs

Storing CDs

Burrs

• Be sure to use round shape CDs only for this

unit and do not use any special shape CDs.

Use of special shape CDs may cause the

unit to malfunction.

• Do not store CDs in areas exposed to direct

sunlight – such as a car seat or above the

fascia panel (dashboard) – or other hot

places.

• Remove CDs from the unit when not

listening to them for a whilst, and put them

back in their cases. Do not stack CDs that

have been removed from their cases or prop

them against something.

Do Not Load CD Accessories in Slot

Do not use commercially available CD

• Be sure to use CDs with disc mark

only for this unit.

— 5 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Buttons and Display

Ba s ic o p e ra t io n s

Tu n e r fe a t u re s

AUD

EJECT

PWR

OFF

PWR

OFF

35Wx4

DISP

SCN

RDM

REP

DISP

SCN

RDM

REP

LOUD

CLK

VOL

ADJ

VOL

ADJ

ATT

TUN / PWR OFF

LOUD / MENU

ATT

TUN

# 1 ~ 6

Preset Station Number

Band display

LOUD indicator

ATT indicator

ST indicator

Frequency

AUTO indicator

MONO indicator

LO.S indicator

— 6 —

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS fe a t u re s

CD p la ye r fe a t u re s

CD / 38 / EJECT

AUD

EJECT

PWR

OFF

PWR

OFF

35Wx4

DISP

SCN

RDM

REP

DISP

SCN

RDM

REP

LOUD

CLK

VOL

ADJ

VOL

ADJ

ATT

RDM

DISP

TI /

VOL ADJ

# 1 ~ 6

SCN

REP

CLK

3 indicator

EON indicator

TA indicator

8 indicator

NEWS indicator

Track time

Track number

TP indicator

AF indicator

SCN indicator

RDM indicator

REP indicator

REG indicator PTY indicator

CD-IN indicator

TI indicator

— 7 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Buttons and Display

Ot h e r fe a t u re s

AUD

EJECT

PWR

OFF

35Wx4

DISP

SCN

RDM

REP

LOUD

CLK

VOL

ADJ

ATT

CLK MENU

Clock display

— 8 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operations (See page 6)

P o w e r

Lo u d n e s s

Turning on the pow er:

This function am plifies low and high tones w hen the volum e

is turned dow n.

Press either the CD or TUN button.

The LOUD indicator lights up, w hen the loudness function is

on.

NOTE

Turn the power on before completing the following procedures.

Turning Loudness On/ Off:

Turning off the pow er:

Press the LOUD button to switch the loudness on and off.

Hold down the PWR OFF button for one second or more.

Vo lu m e

Increasing Volum e:

Press the u button to turn up the volume.

Decreasing Volum e:

Press the d button to turn down the volume.

At t e n u a t o r

This function allow s you to turn dow n the volum e quickly.

Turning Attenuator On/ Off:

Press the ATT button to switch the attenuator on and off.

When the attenuator is on, the ATT indicator blinks.

When the attenuator is off, the volume returns to the original

level.

NOTE

Turning down the volume all the way turns off the attenuator

function.

— 9 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operations (See page 6)

Me n u S ys t e m

Varieties of settings for

each function (display)

Function

To accom m odate a greater num ber of functions, a m enu

system has been em ployed for m aking settings. Press the

MENU button to enter the m enu m ode and then display the

function to m ake the setting. Details on each setting are

explained separately in the corresponding function page.

↓

Disabled System Indicator

News Bulletin Function

Local seek

DSI ON ↔ DSI OFF

↑↓

NEWS 00M ↔ NEWS OFF

Hold down the MENU button for one second or more.

"MENU" is displayed when the menu mode is entered.

The function that you can adjust is indicated with the current

settings displayed.

↑↓

LO.S ON ↔ LO.S OFF

↑↓

Selecting Tuning Mode

Auto Memory Entry

*AF Function

AUTO1 → AUTO2 → MANUAL

↑↓

Selecting function to set

A-MEMORY (start)

Press the ¢ button to search through the functions until you

see the one you want to adjust in the display.

Press the 4 button to search through the functions

backward.

↑↓

AF ON ↔ AF OFF

↑↓

*Region Restrict Function

*Auto TP Seek

REG ON ↔ REG OFF

Example: If you want to switch the tuning mode from AUTO1

to manual, first search through the functions until

you see "AUTO 1" in the display.

↑↓

ATPS ON ↔ ATPS OFF

↑↓

*Monaural Reception

*Programme Type

MONO ON ↔ MONO OFF

↑↓

PTY (PTY mode entered)

Changing setting for currently displayed function

Press either the AM or FM button.

↑

The setting will change for each function.

NOTE

Example: The tuning mode will switch from AUTO 1 to AUTO

2. Pressing the button again switches the setting to

manual, and "MANUAL" is displayed.

• Make sure to end the menu mode when finished.

If you fail to end the menu mode, several funcions may not

operate properly, including the Traffic information function, the

News Bulletin function with PTY news timeout setting, and the

Alarm function.

• Some tuner functions will not be displayed unless you are

currently listening to the tuner.

• Functions marked with an asterisk (*) cannot be used during

AM reception.

• The News function turns on when the setting is made for the

news interruption interval. The "00M" display indicates the

setting selected for the news interruption timeout interval.

With the programme type function and the auto memory

function, the function will start to activate.

NOTE

To use the auto memory function, hold down either the AM or

FM button for two seconds or more.

Ending the m enu m ode

Press the MENU button.

— 10 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features (See page 6)

S e le c t in g Tu n in g Mo d e

NOTE

If the frequencies stored at the preset numbers receive

stations which were not originally memorized when traveling

long distances, the preset number is not displayed. In such

cases, pressing the 4/¢ button to use preset station

seek will receive channel 1.

You can choose from three tuning m odes: auto seek, preset

station seek, and m anual. The “Auto1” indicator lights up

w hen auto seek tuning is selected, and the “Auto2” indicator

lights w hen preset station seek tuning is selected.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

• Manual Tuning

Press the ¢ button to increase the frequency by one step.

Press the 4 button to decrease the frequency by one step.

Press the ¢ button repeatedly until the tuning function

appears in the display.

NOTE

Press the 4 button to search in the other direction.

The tuning method is displayed as “AUTO1,” “AUTO2,” or

“MANUAL,” referring respectively to auto seek tuning, preset

station seek tuning, and manual tuning.

The ST indicator lights up when stereo broadcasts are being

received.

Sw itching settings

Press either the AM button or FM button to switch the tuning

mode.

The display and setting will change.

Lo c a l S e e k Fu n c t io n

Press the MENU button to end the menu mode.

With the local seek function turned on, auto seek tuning skips

stations w ith relatively poor reception.

Turning Local Seek Function On/ Off:

Tu n in g

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the TUN button to turn the radio on.

Press the ¢ button repeatedly until the local seek function

appears in the display.

Press either the FM or AM button to select the band.

Each time you press the FM button, the band switches

between the FM1, FM2 and FM3.

Press the 4 button to search in the other direction.

The function setting is indicated by "LO.S ON" or "LO.S OFF" in

the display, indicating that the local seek function is on or off,

respectively.

Press the AM button to select the MW and LW bands.

• Auto Seek Tuning

Press the ¢ button to seek increasing frequencies.

Press the 4 button to seek decreasing frequencies.

• Preset station seek tuning

Press the ¢ button to move to the next preset station (i.e.,

the one with the next highest number), and the 4 button to

move to the last preset station (i.e., the one with the next

lowest number).

Sw itching settings

Press either the AM button or FM button.

The display and setting will change.

When local seek function is on, the LO.S indicator is turned on.

Press the MENU button to end the menu mode.

— 11 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features (See page 6)

Mo n a u ra l Re c e p t io n

Au t o Me m o ry En t ry

When poor stereo reception is experienced, this function w ill

reduce noise and im prove listening conditions.

You can autom atically store all the receivable frequencies in

the band currently being listened to, and then recall them w ith

the touch of a button later. This function is especially useful

w hen you are travelling and do not know w hat stations are

available. Up to 6 frequencies can be stored this w ay.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the monaural reception

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "MONO ON" or "MONO

OFF" in the display, indicating that monaural reception is on or

off, respectively.

Select the band for auto memory entry.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until "A-MEMORY" appears in

the display.

Press the 4 button to search in the other direction.

Hold down either the AM button or FM button for two seconds

or more to start auto memory function.

The numbers of the preset station buttons showed in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

Sw itching settings

Press either the AM button or FM button.

The display and setting will change.

When monaural reception is on, the MONO indicator turns on.

Press the MENU button to end the menu mode.

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

S t a t io n P re s e t Me m o ry

Store the frequency of the station currently being listened to.

You can then recall that station w ith a single touch of a

button.

NOTE

• When the AF function is turned on whilst auto memory entry

takes place, only RDS stations (i.e., stations with RDS

capability) are stored. RDS stations that have been preset for

FM1 cannot also be preset in FM2 or FM3.

• When the local seek function is turned whilst auto memory

entry takes place, stations with poor reception are not stored.

• When the Traffic Information function is on , only the local

traffic information station frequency will be stored.

Select the band/ station that you want to have stored.

Hold down the button (#1-6) that you want to use for the

station, for two seconds or more.

The button number blinks once in the display to indicate that

the data has been stored.

Recalling a Preset Station:

Cancelling Auto Mem ory Entry During Its Operation:

Press the MENU button whilst auto memory entry is taking

place to stop the process.

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

NOTE

You can store 6 stations in each of the FM1, FM2, FM3, and AM

(MW and LW) bands.

— 12 —

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS features (See page 7)

RDS (Ra d io Da t a S ys t e m )

AF (Alt e rn a t ive Fre q u e n c y) Fu n c t io n

RDS is a digital inform ation system that lets you receive

signals besides those of regular radio program m es, such as

netw ork inform ation being transm itted from radio stations.

When listening to an RDS station (ie, a station w ith RDS

capability), the program m e service nam e of the station is

displayed along w ith the frequency, advising you quickly

w hich station is being received.

When poor reception is experienced, autom atically sw itch to

another frequency broadcasting the sam e program m e in the

sam e RDS netw ork w ith better reception.

The AF indicator lights up w hen the AF function is turned on.

Turning AF Function On/ Off:

Hold down the MENU button for one second or more.

RDS (Radio Data System ) stations also transm it frequency

data for the sam e station. When you are m aking long trips,

this function autom atically sw itches to the particular

frequency w ith the best reception for the particular netw ork of

stations that you w ant to listen to. The data is autom atically

stored, allow ing you to sw itch quickly to another RDS

stations, broadcasting the sam e program m e, that has better

reception. These include stations stored in the station preset

m em ory that you often listen to.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the AF function appears

in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "AF ON" or "AF OFF" in the

display, indicating that the AF function is on or off,

respectively.

Sw itching settings

Press either the AM button or FM button.

The display and setting will change.

EON (En h a n c e d Ot h e r Ne t w o rk )

Stations that offer EON also transm it inform ation about other

RDS stations that have traffic inform ation. When you are

tuned to a station that is not transm itting traffic inform ation,

but another RDS station starts transm itting a traffic bulletin,

the tuner autom atically sw itches to the other station for the

duration of the bulletin.

Press the MENU button to end the menu mode.

Displaying Frequencies:

Hold down the CLK button for one second or more.

The frequency for the RDS station will be displayed for five

seconds instead of the station name.

The EON indicator lights up w hen the RDS station currently

being listened to starts to broadcast EON frequency data.

NOTE

When no other stations with stronger reception are available for

the same programme in the RDS network, you may hear the

incoming broadcast in bits and snatches. Turn off the AF function

in such a case.

Ala rm

When an em ergency transm ission (announcing disasters, etc.)

is sent, all current functions are interrupted to allow the

w arning to be received.

— 13 —

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS features (See page 7)

Re s t ric t in g RDS Re g io n (Re g io n Re s t ric t Fu n c t io n )

Tra ffic In fo rm a t io n Fu n c t io n

You can choose w hether or not to restrict the RDS channels,

received w ith the AF function for a particular netw ork, to a

specific region. When the Region Restrict Function is on, the

region is restricted and the REG indicator is turned on.

You can listen to traffic inform ation. If you are listening to

tapes or discs, they w ill continue playing until a traffic bulletin

is broadcast.

Turning TI function On/ Off:

Turning Region Restrict Function On/ Off:

Press the TI button to turn the function on and off.

When the function is on, the TI indicator is turned on.

When a traffic information station is being received, the TP

indicator will turn on. When none is being received, the TI

indicator will blink on and off.

When a traffic bulletin begins to be broadcast, the TA indicator

will turn on, and reception will begin at the preset volume.

If you are listening to a tape or disc when a traffic bulletin

begins, they will automatically be turned off. When the

bulletin ends or poor reception is experienced, the tape or disc

will begin playing again.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Region restrict

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "REG ON" or "REG OFF" in

the display, indicating that the function is on or off,

respectively.

Sw itching settings

Press either the AM button or FM button.

The display and setting will change.

NOTE

Pressing the TI button whilst in the MW/LW band automatically

switches reception to the FM band. However, the MW/LW band

is not returned to when the TI button is pressed again.

Press the MENU button to end the menu mode.

NOTE

Sw itching to a Different Traffic Inform ation Station:

Use the 4 / ¢ buttons to make an auto seek of the TI

stations in a certain band.

Sometimes stations in the same network broadcast different

programmes or use different programme service names.

NOTE

• When you are listening to a tape or disc, you cannot change to

another TI station.

• When the auto TP seek function is turned on and reception

starts to weaken, the tuner automatically seeks stations with

better reception.

• If you are tuned to a station that is not a traffic information

station itself but which provides EON services, you can still

have traffic information received. The EON indicator lights up

when EON signals are being received.

— 14 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Au t o TP S e e k Fu n c t io n

P re s e t t in g Vo lu m e fo r Tra ffic In fo rm a t io n /Ne w s

When the TI function is on and poor reception conditions are

experienced w hen listening to a traffic inform ation station,

another traffic inform ation station w ith better reception w ill

be searched for autom atically. This function is on, w hen unit

is first pow ered on.

Preset the volum e level to be used for traffic inform ation and

new s broadcasts.

Tune into the station for which you want to set the volume.

Adjust the volume to the desired level.

Turning Auto TP Seek Function On/ Off:

Hold down the VOL ADJ button for two seconds or more.

The volume level blinks once in the display to indicate that the

data has been stored.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Future traffic information/news broadcasts are heard at the

preset level.

Press the ¢ button repeatedly until the Auto TP Seek

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "ATPS ON" or "ATPS OFF"

in the display, indicating that the function is on or off,

respectively.

NOTE

• The volume cannot be lowered by this function during tuner

reception. The volume is only set when it is louder than the

listening volume of the tuner.

• You can arrange only to listen to traffic information or news

bulletins with at preset volume with the volume set at

minimum.

Sw itching settings

Press either the AM button or FM button.

The display and setting will change.

If the traffic information station you are tuned to experiences

poor reception, this function automatically seeks another TP

station after about 30 seconds.

Press the MENU button to end the menu mode.

— 15 —

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS features (See page 7)

NOTE

Ne w s Bu lle t in Fu n c t io n

w it h P TY Ne w s Tim e o u t S e t t in g

If you choose the "20M" setting, further news bulletins will not be

received for 20 minutes once the first news bulletin is received.

Setting the interval at the "00M" factory default indicates no

News Timeout will be made, meaning that additional news

bulletins will continue to be searched for.

You can arrange to have new s bulletins interrupt your current

listening source, including other radio stations. When the

New s Bulletin function is on, the PTY New s Tim eout setting

allow s you to set the interval during w hich further new s

interruption cannot take place. You can adjust the PTY new s

interruption period from 10 to 90 m inutes on each journey.

Press the MENU button to end the menu mode.

NOTE

Turning New s Bulletin Function On/ Off:

• This function is only available if the desired station sends PTY-

code for news bulletin or belongs to EON-Network sending

PTY-code for news bulletin.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

• If you turn on the news bulletin function in the MW/LW band,

the band is switched automatically to the FM band.

However, the MW/LW band is not returned to when you turn

off the function.

Press the ¢ button repeatedly until the News Bulletin

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "NEWS 00M" or

"NEWS OFF" in the display, indicating that the function is on or

off, respectively.

NOTE

Depending on the interval chosen, the "00M" in the display will

change when the function is turned on.

Changing the Function Setting

Press either the FM or AM button.

Each time you press the FM or AM button until the desired

setting is displayed.

Press the FM button to increase the interval, and the AM

button to decrease it.

OFF ↔ 00M ↔ 10M ↔ 20M ↔ 30M ↔ 40M ↔ 50M ↔ 60M

↔ 70M ↔ 80M ↔ 90M

(M= minutes)

When you select the news interruption timeout interval, the

News function turns on and the NEWS indicator lights up.

When a news bulletin is received, the NEWS indicator will blink

and reception will begin at the preset volume.

— 16 —

Download from Www.Somanuals.com. All Manuals Search And Download.

18.Children’s programmes(CHILDREN) ↔ 19.Social

Affairs(SOCIAL A) ↔ 20.Religion(RELIGION) ↔ 21.Phone

In(PHONE IN) ↔ 22.Travel(TRAVEL) ↔ 23.Leisure(LEISURE)

↔ 24.Jazz Music(JAZZ) ↔ 25.Country Music(COUNTRY) ↔

26.National Music(NATION M) ↔ 27.Oldies Music(OLDIES)

↔ 28.Folk Music(FOLK M) ↔

P ro g ra m m e Typ e (P TY) Fu n c t io n

Conduct auto seek tuning only on those stations w ith selected

kinds of program m es.

Selecting Type of Program m e to be Received:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

29.Documentary(DOCUMENT) ↔ Music(MUSIC) ↔

Speech(SPEECH)↔

Press the ¢ button repeatedly until "PTY" appears in the

display.

(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)

• You can select the type of programme directly by pressing a

preset button. The buttons are factory-set to the following

type of programmes:

Press the 4 button to search in the other direction.

Press either the AM button or FM button.

The PTY indicator will turn on, and the Programme Type

Selection (PTY) Mode entered.

1. Music

4. Other Music

2. Speech

5. Serious Classical

3. News

6. Varied

NOTE

If you make no key input in 30 seconds, the mode will

automatically turn off.

Changing the Preset Button Settings for Programme Type

After selecting the type of programme to be stored in a certain

preset button, hold down that button for two seconds or more.

The previously stored data for that button are erased and the

new programme type is stored.

NOTE

• You cannot use this function whilst the traffic information

function is turned on.

• The time is not displayed until you have turned off the

programme type function.

Seeking the selected program m e type

Press the 4 or ¢ button to make a seek of frequencies

with your selected type of programme.

NOTE

Changing the Display Language to French or German

The display blinks and the seek starts.

In the PTY mode, hold down the CLK button for one second or

more to display the name of the language currently used.

If you want to change the language, press the preset button for

the desired language and then the CLK button.

If your selected type of programme is found, the name of the

station is displayed and the station is tuned into.

The PTY indicator blinks in the display for about 30 seconds.

If you make no key input in 30 seconds, the PTY selection

mode will turn off automatically.

English is #1, French is #2, and German is #3.

Select the type of program m e to be received

• Press either the FM or AM buttons repeatedly to select the

type of programme you want to listen to.

NOTE

If no programme can be found, "NO PTY" is displayed.

If you want to select another type of programme, repeat steps 4

and 5 above.

The selection includes:

Speech(SPEECH) ↔ 1.News(NEWS) ↔ 2.Current

Affairs(AFFAIRS) ↔ 3.Information(INFO) ↔

4.Sports(SPORT) ↔ 5.Education(EDUCATE) ↔

6.Drama(DRAMA) ↔ 7.Culture(CULTURE) ↔

8.Science(SCIENCE) ↔ 9.Varied(VARIED) ↔ 10.Pop

Music(POP M) ↔ 11.Rock Music(ROCK M) ↔ 12.M,O,R

Music(M.O.R. M) ↔ 13.Light Classical(LIGHT M) ↔

14.Serious Classical(CLASSICS) ↔ 15.Other Music(OTHER

M) ↔ 16.Weather(WEATHER) ↔ 17.Finance(FINANCE) ↔

Sw itching to Other Stations w ith the Sam e Type of

Program m e:

When the PTY indicator is blinking in the display, perform auto

seek tuning.

The tuner scans for another station with the same type of

programme.

Cancelling Program m e Type Function During Its Operation:

Press the MENU button.

— 17 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD player features (See page 7)

P la yin g CDs

S w it c h in g Dis p la y fo r CDs

Playing CDs:

Sw itch the display that appears w hilst discs are playing.

If no CDs are inserted, insert one in the slot with the label

facing up. (If a CD is already inserted, press the CD button).

The CD-IN indicator lights up when a CD has been inserted.

The 3 indicator lights up when a CD is being played.

Sw itching Display for CDs:

Each time you press the DISP button, the display during CD

play switches as follows.

Pausing and Restarting CD Play:

▼

Press the 38 button to make the disc pause. The 8 indicator

Track time

▼

lights up.

Total disc playing time

Press the same button again to start play again.

Stopping and Ejecting CDs:

Hold down the EJECT button for one second or more.

The CD stops playing and ejects from the slot.

Tra c k S e a rc h

2CAUTION

Search forw ards or backw ards through the tracks on the disc

until you reach the one that you w ant to listen to.

• Do not attempt to insert a CD into the slot if another one is

already there.

• The unit can only play 12-cm (5-inch) CDs. If you insert an 8-cm

(3-inch) CD, it will get stuck inside and can cause the unit to

malfunction.

Making a Reverse Track Search:

Press the 4 button to display the desired track number.

Press once to search back to the beginning of the current

track, twice to search back to the beginning of the previous

track, and so forth.

NOTE

When you load a CD and eject it right away, the next time you try

to insert the CD may not load. In such a situation, take the CD

out for a moment and then reinsert it.

Play starts at the beginning of the displayed track number.

Making a Forw ard Track Search:

Press the ¢ button to display the desired track number.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

Play starts at the beginning of the displayed track number.

Fa s t Fo rw a rd in g a n d Re ve rs in g Dis c P la y

Fast Forw arding Disc Play:

Hold down on the ¢ button.

Release your finger to play the disc at that point.

Reversing Disc Play:

Hold down on the 4 button.

Release your finger to play the disc at the point.

— 18 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tra c k Re p e a t Fu n c t io n

Ra n d o m P la y Fu n c t io n

Repeat playing the current track.

Play all the tracks on the current disc in random order.

Turning Repeat Play Function On/ Off:

Press the REP button to switch the repeat play function on and

off.

Press the RDM button to switch the random play function on

and off.

The RDM indicator lights up when the random play function is

turned on.

The display of the track number changes continuously as the

next track is being selected.

The REP indicator lights up when the repeat play function is

turned on.

The track number currently being heard blinks in the display.

When the track has been selected, play starts.

The selected track number blinks in the display as it is being

played.

NOTE

The repeat play function is cancelled when you stop playing the

disc.

To change the track being heard, press the ¢ button.

Another track is selected and played.

Tra c k S c a n Fu n c t io n

NOTE

Successively play the beginning of each track on a disc until

you find the track that you w ant to listen to.

The random play function is cancelled when you stop playing a

disc.

Turning Track Scan Function On/ Off:

Press the SCN button to switch the track scan function on and

off.

The SCN indicator lights up when the track scan function is

turned on.

The first 10 seconds of each track are played, and the tracks

are played in order.

The track number currently being heard blinks in the display.

Stopping to Listen to the Track Being Scanned:

Press the CD or SCN button again to stop the scan and keep

on listening to a track normally.

NOTE

• The track scan function is cancelled when you stop playing a

disc.

• The track scan function only scans each track on a disc once.

— 19 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Other features (See page 8)

Au d io Co n t ro l S e t t in g

Clo c k Dis p la y

Adjust various param eters of sound quality.

Display the tim e.

Sw itching to Tim e Display:

Press the AUD button to enter the control mode.

Each time the AUD button is pressed, the adjustment mode

display changes as follows:

Press the CLK button repeatedly until the clock is displayed.

7 Bass 7 Treble 7 Balance 7 Fader 7 Volume

Ad ju s t in g Tim e

If you do not move to step 2 in 5 seconds, the unit will switch

back to the volume adjustment mode (i.e., the normal mode).

When the RDS station tuned into is transm itting a tim e signal,

have the unit’s built-in tim e adjust autom atically to the

correct local tim e.

NOTE

Source tone memory

Each source (CD, FM, and AM) has its own memory in which to

store the bass and treble tone settings.

The settings made for a particular source are then recalled

automatically whenever you use that source (e.g., FM mode uses

the tone settings made for FM, AM for AM, etc.).

Adjusting the Tim e:

Tune into an RDS station for 3 or 4 minutes.

The time adjusts automatically to the correct local time.

NOTE

• The displayed time cannot be set manually, but only through

RDS station time signals.

• The time is not adjusted when the RDS station you are tuned to

is not transmitting a time signal. Choose another RDS station in

such a case.

Press the d/u buttons to adjust the mode shown in the

display.

Use the following table as a guide for adjusting the settings in

each mode.

Adjustment

mode

(Display)

Operation of Audio control button

d button

u button

Bass

(“BAS”)

Bass decreased.

Bass increased.

Treble

(“TRE”)

Treble decreased.

Treble increased.

Balance

(“BAL”)

Left channel

emphasized.

Right channel

emphasized.

Fader

(“FAD”)

Rear channel

increased.

Front channel

increased.

— 20 —

Download from Www.Somanuals.com. All Manuals Search And Download.

DS I (Dis a b le d S ys t e m In d ic a t o r)

Th e ft De t e rre n t Fa c e p la t e

A red indicator blinks on the unit after the faceplate is

rem oved, w arning potential thieves. The factory default for

this function is "ON".

The faceplate of the unit can be detached and taken w ith you,

helping to deter theft.

Turning Disabled System Indicator On/ Off:

Projections

Release button

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Grooves

Press the ¢ button repeatedly until the Disabled System

Indicator function appears in the display.

Press the 4 button to search in the other direction..

The function setting is indicated by "DSI ON" or "DSI OFF" in

the display, indicating that the disable system indicator is on or

off, respectively.

Rem oving Faceplate:

Press the release button.

The faceplate is unlocked, allowing you to detach it.

NOTE

Sw itching settings

Press either the AM button or FM button.

The display and setting will change.

• The faceplate is a precision piece of equipment and can be

damaged by shocks or jolts. For that reason, keep the faceplate

in its special storage case whilst detached.

Press the MENU button to end the menu mode.

• Do not expose the faceplate or its storage case to direct

sunlight or excessive heat or humidity. Also avoid places with

too much dust or the possibility of water splashing.

Reattaching Faceplate:

Align the projections on the unit with the grooves on the

faceplate.

Push the faceplate in until it clicks.

The faceplate is locked in place, allowing you to use the unit.

— 21 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Ac c e s s o rie s

2CAUTION

• If your car is not prepared for this special connection-system,

consult your KENWOOD dealer.

External view

Num ber of item s

• Only use antenna conversion adapters (ISO-JASO) when the

antenna cord has an ISO plug.

• Make sure that all cable connections are securely made by

inserting jacks until they lock completely.

..........................................1

• If your vehicle's ignition does not have an ACC position, or if

the ignition cable is connected to a power source with constant

voltage such as a battery cable, the power will not be linked

with the ignition (i.e., it will not turn on and off along with the

ignition). If you want to link the unit's power with the ignition,

connect the ignition cable to a power source that can be turned

on and off with the ignition key.

• If the fuse blows, first make sure that the cables have not

caused a short circuit, then replace the old fuse with one with

the same rating.

• Do not let unconnected cables or terminals touch metal on the

car or anything else conducting electricity. To prevent short

circuits, also do not remove the caps on the ends of the

unconnected cables or the terminals.

• Connect the speaker cables correctly to the terminals to which

they correspond. The unit may receive damage or fail to work if

you share the - cables and/or ground them to any metal part in

the car.

..........................................2

..........................................1

2CAUTION

The use of any accessories except for those provided might result

in damage to the unit. Make sure only to use the accessories

shipped with the unit, as shown above.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

• Insulate unconnected cables with vinyl tape or other similar

material.

In s t a lla t io n P ro c e d u re

1. To prevent short circuits, remove the key from the ignition and

disconnect the -terminal of the battery.

2. Make the proper input and output cable connections for each unit.

3. Connect the cable on the wiring harness.

4. Take Connector B on the wiring harness and connect it to the

speaker connector in your vehicle.

5. Take Connector A on the wiring harness and connect it to the

external power connector on your vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

8. Reconnect the - terminal of the battery.

9. Press the reset button.

— 22 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Co n n e c t in g Ca b le s t o Te rm in a ls

FM/AM antenna input

Antenna Cord (ISO)

Rear left output (White)

Rear right output (Red)

Antenna Conversion Adaptor (ISO–JASO)

(Accessory4)

Fuse

Wiring harness

(Accessory1)

Connector Function Guide

Pin Num bers for

Cable Colour

Functions

ISO Connectors

Battery cable (Yellow)

Ignition cable (Red)

External Power

Connector

A–4

A–5

A–7

A–8

Yellow

Blue/White

Red

Battery

Power Control

Ignition (ACC)

Earth (Ground)

Connection

Black

A–7 Pin (Red)

Speaker

Connector

A–4 Pin (Yellow)

B–1

B–2

B–3

B–4

B–5

B–6

B–7

B–8

Purple

Purple/Black

Gray

Gray/Black

White

White/Black

Green

Rear Right (+)

Rear Right (–)

Front Right (+)

Front Right (–)

Front Left (+)

Front Left (–)

Rear Left (+)

Rear Left (–)

Power control cable

(Blue/White)

When using the optional power amplifier,

connect to its power control terminal.

P.CONT.OUT

Green/Black

Connector A

If no connections are made, do not

let the cable come out from the tab.

Connector B

— 23 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Co n n e c t in g Ca b le s t o Te rm in a ls

In s t a lla t io n

■

2WARNING

Installation

Connecting the ISO Connector (see p.23)

The pin arrangement for the ISO connectors depends on the type

of vehicle you drive. Make sure to make the proper connections to

prevent damage to the unit.

Firewall or metal support

The default connection for the wiring harness is described in 1

below. If the ISO connector pins are set as described in 2 or 3,

make the connection as illustrated.

Accessory3

1 (Default setting) The A-7 pin (red) of the vehicle's ISO

connector is linked with the ignition, and the A-4 pin (yellow) is

connected to the constant power supply.

Unit

Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Bend the tabs of the

mounting sleeve with

a screwdriver or

similar utensil and

attach it in place.

Battery cable (Yellow)

A–4 Pin (Yellow)

2 The A-7 pin (red) of the vehicle's ISO connector is connected to

the constant power supply, and the A-4 pin (yellow) is linked to

the ignition.

Metal mounting

strap

(commercially

available)

Self-tapping

screw

(commercially

available)

Unit

Vehicle

Ignition cable (Red)

A–7 Pin (Red)

NOTE

Battery cable (Yellow)

A–4 Pin (Yellow)

Make sure that the unit is installed securely in place. If the unit is

unstable, it may malfunction (eg, the sound may skip).

3 The A-4 pin (yellow) of the vehicle's ISO connector is not

connected to anything, while the A-7 pin (red) is connected to

the constant power supply (or both the A-7 (red) and A-4

(yellow) pins are connected to the constant power supply).

Unit

Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

NOTE

When the connection is made as in 3 above, the unit's power will

not be linked to the ignition key. For that reason, always make sure

to turn off the unit's power when the ignition is turned off.

To link the unit's power to the ignition, connect the ignition cable

(ACC...red) to a power source that can be turned on and off with

the ignition key.

— 24 —

Download from Www.Somanuals.com. All Manuals Search And Download.

■

Rem oving the hard rubber fram e

Rem oving the Unit

Refer to the section “Removing the hard rubber frame” and

then remove the hard rubber frame.

Engage the catch pins on the removal tool and remove the two

locks on the lower level.

Lower the frame and pull it forward as shown in the figure.

Remove the Hex-head screw with integral washer (M4×8) on

the back panel.

Insert the two removal tools deeply into the slots on each side,

as shown.

Catch

Lock

Accessory3

Catch facing up

Accessory2

Removal tool

When the lower level is removed, remove the upper two

locations.

Lower the removal tool

toward the bottom, and pull

out the unit halfway whilst

pressing towards the

inside.

2CAUTION

Be careful to avoid injury from the catch pins on the removal tool.

NOTE

Pull the unit all the way out

with your hands, being

careful not to drop it.

The frame can be removed from the top side in the same

manner.

— 25 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tro u b le s h o o t in g Gu id e

What m ight appear to be a m alfunction in your unit m ay just be the result of slight m isoperation or m isw iring. Before

calling service, first check the follow ing table for possible problem s.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not turn on.

The fuse has blown.

After checking for short circuits in the cables, replace the

fuse with one having the same rating.

No ACC position on vehicle ignition.

The Attenuator function is turned on.

Connect the same cable to the ignition as the battery cable.

Turn off the Attenuator function.

No sound can be heard, or the

volume is low.

The fader and/or balance settings are set all the way to

one side.

Reset the fader and/or balance settings.

The input/output cables or wiring harness are connected

incorrectly.

Reconnect the input/output cables and/or the wiring harness

correctly. See the section on "Connecting Cables to

Terminals".

Nothing happens when the

buttons are pressed.

The computer chip in the unit is not functioning normally.

Press the reset button on the unit (see page 4).

The sound quality is poor or

distorted.

A speaker cable may be pinched by a screw in the car.

The speakers are not wired correctly.

Check the speaker wiring.

Reconnect the speaker cables so that each output terminal

is connected to a different speaker.

Radio reception is poor.

The car antenna is not extended.

Pull out the antenna all the way.

The antenna control cable is not connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The memory is erased when

the ignition is turned off.

The battery cable has not been connected to the proper

terminal.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The ignition and battery cable are incorrectly connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

A CD ejects as soon as it is

loaded.

The CD is upside-down.

The CD is quite dirty.

Load the CD with the labelled side up.

Clean the CD, referring to the section on "Cleaning CDs" (see

page 5).

The sound skips on a CD.

The CD is scratched or dirty.

Random play has been selected.

— 26 —

Clean the CD, referring to the section on "Cleaning CDs" (see

page 5).

The specified track does not

play.

Turn off the random play function.

Download from Www.Somanuals.com. All Manuals Search And Download.

S p e c ific a t io n s

Specifications subject to change w ithout notice.

FM tuner section

Audio section

Frequency range (50 kHz Space) ..............87.5 MHz – 108.0 MHz

Usable sensitivity (S/N=26dB) ....................................0.7 µV/75 Ω

Quieting Sensitivity (S/N=46dB)..................................1.6 µV/75 Ω

Frequency response (±3.0 dB) ..............................30 Hz – 15 kHz

Signal to Noise ratio (MONO) ..............................................68 dB

Selectivity (DIN) (400kHz)..................................................≥ 80 dB

Stereo separation (1 kHz) ....................................................35 dB

Maximum output power..................................................35 W × 4

Output power (DIN 45324, +B=14.4V)............................20 W × 4

Tone action

Bass: ............................................................100 Hz ±10 dB

Treble: ..........................................................10 kHz ±10 dB

Preout level / Load ................................................1800 mV/10 kΩ

Preout impedance ............................................................≤ 600 Ω

MW tuner section

General

Frequency range (9kHz Space) ......................531 kHz – 1611 kHz

Usable sensitivity (S/N=20dB) ..............................................30 µV

Operating voltage ..............................14.4 V (11 – 16 V allowable)

Current consumption ................................10.0 A at Rated power

Installation size (W × H × D)..........................182 × 53 × 160 mm

Weight ................................................................................1.4 kg

LW tuner section

Frequency range ..............................................153 kHz – 281 kHz

Usable sensitivity (S/N=20dB) ..............................................45 µV

CD player section

Laser diode ....................................................GaAlAs (λ=780 nm)

Digital filter (D/A) ......................................8 Times Over Sampling

D/A Converter ........................................................................1 Bit

Spindle speed ..............................................500 – 200 rpm (CLV)

Wow & Flutter ........................................Below Measurable Limit

Frequency response (±1 dB)..................................10 Hz – 20 kHz

Total harmonic distortion (1 kHz)........................................0.01 %

Signal to Noise ratio ............................................................93 dB

Dynamic range ....................................................................93 dB

Channel separation ..............................................................85 dB

— 27 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Insignia Portable DVD Player NS P7DVD15 User Manual
Interact TV Baby Toy INS 50400 100409 US User Manual
JVC Security Camera LST0728 001C User Manual
JVC Stereo System CA MXGT91R User Manual
Karcher Pressure Washer G 2000 ET User Manual
Kathrein Satellite TV System cap910 User Manual
Klipsch Speaker CDT ARCHITECTURAL User Manual
Klipsch Speaker IC 400 T User Manual
Kramer Electronics Welding System 482xl User Manual
Krell Industries CD Player KAV 250cd 2 User Manual