INSTALLATION MANUAL
RESIDENTIAL GAS FURNACE MODELS
EFFICIENCY
RATING
CERTIFIED
TG9S*MP, GG9S*MP
ISO 9001
Certified Quality
Management System
(95.5% AFUE Single Stage Multi-position)
LIST OF SECTIONS
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DUCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
GAS PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ELECTRICAL POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TWINNING AND STAGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CONDENSATE PIPING AND FURNACE
COMBUSTION AIR and VENT SYSTEM . . . . . . . . . . . . . . . . . . . .24
START-UP AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . .31
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
REPLACEMENT PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
REPLACEMENT PART CONTACT INFORMATION . . . . . . . . . . . .39
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
VENTING CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LIST OF FIGURES
Duct Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Vertical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Coil Flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Horizontal Right Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Horizontal Left Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PC Series Upflow Coil Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Horizontal Left or Right application (Right Shown) . . . . . . . . . . . . . . 6
Combustible Floor Base Accessory . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Horizontal Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Attic Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Suspended Furnace / Crawl Space Installation . . . . . . . . . . . 7
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Side Return Cutout Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Gas Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Upflow/Downflow Gas Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Horizontal Gas Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Thermostat Chart - Single Stage AC with
Single Stage Twinning Wiring Diagram . . . . . . . . . . . . . . . . . . . . . .15
Two-Stage Twinning Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . .15
Upflow Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Downflow Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Horizontal Left Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Horizontal Right Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Home Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Termination Configuration - 1 Pipe . . . . . . . . . . . . . . . . . . . . . . . . . .24
Termination Configuration - 2 Pipe . . . . . . . . . . . . . . . . . . . . . . . . . .24
Termination Configuration - 2 Pipe Basement . . . . . . . . . . . . . . . . .24
Double Horizontal Combustion Air Intake and Vent Termination . . .24
Double Vertical Combustion Air Intake and Vent Termination . . . . .24
Direct Vent Air Intake Connection and Vent Connection . . . . . . . . .25
Combustion Airflow Path Through The Furnace Casing . . . . . . . . .25
Outside and Ambient Combustion Air . . . . . . . . . . . . . . . . . . . . . . . .26
Attic and Crawl Space Combustion Air Termination . . . . . . . . . . . . .27
Gas Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Reading Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Furnace Control Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Furnace Control Event Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Single Stage PSC Furnaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Thermostat Chart - Single Stage HP with
Single Stage PSC Furnaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Typical Twinned Furnace Application . . . . . . . . . . . . . . . . . . . . . . . 14
LIST OF TABLES
Unit Clearances to Combustibles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Coil Projection Dimensions - PC Series Coils . . . . . . . . . . . . . . . . . . 6
Cabinet and Duct Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Recommended Filter Sizes (High Velocity 600 FPM) . . . . . . . . . . . . 8
Nominal Manifold Pressure - High Fire . . . . . . . . . . . . . . . . . . . . . . 10
Ratings & Physical / Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . 11
Maximum Equivalent Pipe Length . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Elbow Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Equivalent Length of Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Combustion Air Intake and Vent Connection Size at Furnace (All Mod-
els) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Estimated Free Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Unconfined Space Minimum Area in Square Inch . . . . . . . . . . . . . .26
Free Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Gas Rate (CU FT/HR) at Full Input . . . . . . . . . . . . . . . . . . . . . . . . . .29
Inlet Gas Pressure Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Nominal Manifold Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
These high efficiency, compact units employ induced combustion, reli-
able hot surface ignition and high heat transfer aluminized tubular heat
exchangers. The units are factory shipped for installation in upflow or
horizontal applications and may be converted for downflow applica-
tions.
DANGER indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation, which, if not
avoided may result in minor or moderate injury. It is also used to
alert against unsafe practices and hazards involving only property dam-
age.
These furnaces are designed for residential installation in a basement,
closet, alcove, attic, recreation room or garage and are also ideal for
commercial applications. All units are factory assembled, wired and
tested to assure safe dependable and economical installation and oper-
ation.
These units are Category IV listed and may not be common vented with
another gas appliance as allowed by the National Fuel Gas Code.
Improper installation may create a condition where the operation of
the product could cause personal injury or property damage.
Improper installation, adjustment, alteration, service or mainte-
nance can cause injury or property damage. Failure to carefully
read and follow all instructions in this manual can result in fur-
nace malfunction, death, personal injury and/or property dam-
age. Only a qualified contractor, installer or service agency should
install this product.
SECTION I: SAFETY
This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.
Understand and pay particular attention to the signal words DANGER,
WARNING, or CAUTION.
364861-UIM-B-0708
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
These instructions cover minimum requirements and conform to exist-
ing national standards and safety codes. In some instances these
instructions exceed certain local codes and ordinances, especially
those who have not kept up with changing residential and non-HUD
modular home construction practices. These instructions are required
as a minimum for a safe installation.
The furnace area must not be used as a broom closet or for any
other storage purposes, as a fire hazard may be created. Never
store items such as the following on, near or in contact with the fur-
nace.
1. Spray or aerosol cans, rags, brooms, dust mops, vacuum
cleaners or other cleaning tools.
FOR FURNACES INSTALLED IN THE COMMON-
WEALTH OF MASSACHUSETTS ONLY
2. Soap powders, bleaches, waxes or other cleaning com-
pounds; plastic items or containers; gasoline, kerosene, ciga-
rette lighter fluid, dry cleaning fluids or other volatile fluid.
3. Paint thinners and other painting compounds.
For all side wall horizontally vented gas fueled equipment installed in
every dwelling, building or structure used in whole or in part for resi-
dential purposes, including those owned or operated by the Com-
monwealth and where the side wall exhaust vent termination is less
than seven (7) feet above finished grade in the area of the venting,
including but not limited to decks and porches, the following require-
ments shall be satisfied:
4. Paper bags, boxes or other paper products
Never operate the furnace with the blower door removed. To
do so could result in serious personal injury and/or equipment
damage.
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At
the time of installation of the side wall horizontal vented gas
fueled equipment, the installing plumber or gasfitter shall
observe that a hard wired carbon monoxide detector with an
alarm and battery back-up is installed on the floor level where
the gas equipment is to be installed. In addition, the installing
plumber or gasfitter shall observe that a battery operated or
hard wired carbon monoxide detector with an alarm is installed
on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment.
It shall be the responsibility of the property owner to secure the
services of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors
CODES AND STANDARDS
Follow all national, local codes and standards in addition to this installa-
tion manual. The installation must comply with regulations of the serv-
ing gas supplier, local building, heating, plumbing, and other codes. In
absence of local codes, the installation must comply with the national
codes listed below and all authorities having jurisdiction.
In the United States and Canada, follow all codes and standards for the
following, using the latest edition available:
STEP 1 -Safety
•
US: National Fuel Gas Code (NFGC) NFPA 54/ANSI Z223.1 and
the Installation Standards, Warm Air Heating and Air Conditioning
Systems ANSI/NFPA 90B
a. In the event that the side wall horizontally vented gas
fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent floor
level.
•
CANADA: CAN/CGA-B149.1 National Standard of Canada. Natu-
ral Gas and Propane Installation Codes (NSCNGPIC)
STEP 2 -General Installation
•
US: Current edition of the NFGC and NFPA 90B. For copies, con-
tact the
b. In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply with
the above requirements; provided, however, that during
said thirty (30) day period, a battery operated carbon mon-
oxide detector with an alarm shall be installed.
National Fire Protection Association Inc.
Batterymarch Park
Quincy, MA 02269
or for only the NFGC, contact the
American Gas Association,
400 N. Capital, N.W.
2. APPROVED CARBON MONOXIDE DETECTORS. Each car-
bon monoxide detector as required in accordance with the
above provisions shall comply with NFPA 720 and be ANSI/UL
2034 listed and IAS certified.
Washington DC 20001
3. SIGNAGE. A metal or plastic identification plate shall be perma-
nently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled
heating appliance or equipment. The sign shall read, in print
size no less than one-half (1/2) inch in size, "GAS VENT
DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUC-
TIONS".
•
CANADA: NSCNGPIC. For a copy contact:
Standard Sales, CSA International
178 Rexdale Boulevard
Etobicoke, (Toronto) Ontario Canada M9W 1RS
STEP 3 -Combustion and Ventilation Air
•
•
US: Section 5.3 of the NFGC, air for Combustion and Ventilation
CANADA: Part 7 of NSCNGPIC, Venting Systems and Air Supply
for Appliances
4. INSPECTION. The state or local gas inspector of the side wall
horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes car-
bon monoxide detectors and signage installed in accordance
with the provisions of 248 CMR 5.08(2)(a)1 through 4.
STEP 4 -Duct Systems
US and CANADA: Air Conditioning Contractors Association
•
(ACCA) Manual D, Sheet Metal and Air Conditioning Contractors
Association National Association (SMACNA), or American Soci-
ety of Heating, Refrigeration, and Air Conditioning Engineers
(ASHRAE) 1997 Fundamentals Handbook Chapter 32.
INSPECTION
STEP 5 -Acoustical Lining and Fibrous Glass Duct
As soon as a unit is received, it should be inspected for possible dam-
age during transit. If damage is evident, the extent of the damage
should be noted on the carrier’s freight bill. A separate request for
inspection by the carrier’s agent should be made in writing. Also, before
installation, the unit should be checked for screws or bolts which may
have loosened in transit. There are no shipping or spacer brackets
which need to be removed from the interior of this unit.
•
US and CANADA: Current edition of SMACNA and NFPA 90B as
tested by UL Standard 181 for Class I Rigid Air Ducts
STEP 6 -Gas Piping and Gas Pipe Pressure Testing
•
•
US: NFGC; chapters 2, 3, 4, & 9 and National Plumbing Codes
CANADA: NSCNGPIC Part 5
STEP 7 -Electrical Connections
•
•
US: National Electrical Code (NEC) ANSI/NFPA 70
CANADA: Canadian Electrical Code CSA C22.1
Johnson Controls Unitary Products
3
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
FURNACE LOCATION AND CLEARANCES
Table 1: Unit Clearances to Combustibles
The furnace shall be located using the following guidelines:
Upflow
Downflow
Horizontal
Application
Top
1. Where a minimum amount of air intake/vent piping and elbows will
be required.
1"
0"
0"
0"
0"
0"
0"
Vent
0"
0"
2. As centralized with the air distribution as possible.
3. Where adequate combustion air will be available (particularly
when the appliance is not using outdoor combustion air).
4. Where it will not interfere with proper air circulation in the confined
space.
5. Where the outdoor vent terminal will not be blocked or restricted.
Refer to “VENT CLEARANCES” located in SECTION VII of these
instructions. These minimum clearances must be maintained in
the installation.
Rear
0"
0"
Side
0"
1"
0"
Front*
Floor
0"
Combustible
Yes
Combustible1
Combustible
Yes
Closet
Line Contact
Yes
No
No
Yes
1. For combustible floors only when used with special sub-base.
* - 24" clearance in front and 18" on side recommended for service access.
All furnaces approved for alcove and attic installation.
6. Where the unit will be installed in a level position with no more than
1/4” (6.4 mm) slope side-to-side and front-to-back to provide
proper condensate drainage.
SECTION II: DUCTWORK
DUCTWORK GENERAL INFORMATION
Installation in freezing temperatures:
1. Furnace shall be installed in an area where ventilation facilities
provide for safe limits of ambient temperature under normal oper-
ating conditions. Ambient temperatures must not fall below 32°F
(0°C) unless the condensate system is protected from freezing.
The duct system’s design and installation must:
1. Handle an air volume appropriate for the served space and within
the operating parameters of the furnace specifications.
2. Be installed in accordance of National Fire Protection Association
as outlined in NFPA standard 90B (latest editions) or applicable
national, provincial, state, and local fire and safety codes.
3. Create a closed duct system. For residential and Non-HUD Modu-
lar Home installations, when a furnace is installed so that the sup-
ply ducts carry air circulated by the furnace to areas outside the
space containing the furnace, the return air shall also be handled
by a duct(s) sealed to the furnace casing and terminating outside
the space containing the furnace.
Improper installation in an ambient below 32ºF (0.0° C) could create
a hazard, resulting in damage, injury or death.
2. Do not allow return air temperature to be below 55º F (13° C) for
extended periods. To do so may cause condensation to occur in
the main heat exchanger, leading to premature heat exchanger
failure.
3. If this furnace is installed in an unconditioned space and an
extended power failure occurs, there will be potential damage to
the internal components. Following a power failure situation, do
not operate the unit until inspection and repairs are performed.
4. Complete a path for heated or cooled air to circulate through the
air conditioning and heating equipment and to and from the condi-
tioned space.
4. Special precautions MUST be made if installing furnace in an area
which may drop below freezing. This can cause improper opera-
tion or damage to the equipment. If the furnace is installed in an
area that has the potential of freezing, the drain line must be pro-
tected. Use a 3 to 6 watt per foot at 115 vac, 40º F (4.4° C) self-
regulating, shielded and waterproof heat tape. Wrap the drain line
outside of the furnace with the heat tape and secure with ties. Fol-
low the heat tape manufacturer's recommendations.
The cooling coil must be installed in the supply air duct, down-
stream of the furnace. Cooled air may not be passed over the heat
exchanger.
When the furnace is used with a cooling coil, the coil must be installed
parallel with, or in the supply air side of the furnace to avoid condensa-
tion in the primary heat exchanger. When a parallel flow arrangement is
used, dampers or other means used to control airflow must be ade-
quate to prevent chilled air from entering the furnace. If manually oper-
ated, the damper must be equipped with means to prevent the furnace
or the air conditioner from operating unless the damper is in full heat or
cool position.
Use only Propylene Glycol (RV anti-freeze) to winterize the furnace.
Refer to the manufacturer’s specification to ensure that it is compat-
ible with plastics and other components of the furnace. DO NOT
use Ethylene Glycol anti-freeze in the furnace.
When replacing an existing furnace, if the existing plenum is not the
same size as the new furnace then the existing plenum must be
removed and a new plenum installed that is the proper size for the new
furnace. If the plenum is shorter than 12” (30.5 cm) the turbulent air flow
may cause the limit controls not to operate as designed, or the limit con-
trols may not operate at all.
Clearances for access/service:
Ample clearances should be provided to permit easy access to the unit.
The following minimum clearances are recommended:
1. Twenty-four (24) inches (61 cm) between the front of the furnace
and an adjacent wall or another appliance, when access is
required for servicing and cleaning.
The duct system is a very important part of the installation. If the duct
system is improperly sized the furnace will not operate properly.
The ducts attached to the furnace plenum, should be of sufficient size
so that the furnace operates at the specified external static pressure
and within the air temperature rise specified on the nameplate.
2. Eighteen (18) inches (46 cm) at the side where access is required
for passage to the front when servicing or for inspection or replace-
ment of flue/vent connections.
In all cases, accessibility clearances shall take precedence over clear-
ances for combustible materials where accessibility clearances are
greater.
The minimum plenum height is 12” (30.5 cm). The furnace will not
operate properly on a shorter plenum height. The minimum recom-
mended rectangular duct height is 4 inches (10 cm) attached to the
plenum.
Installation in a residential garage:
A gas-fired furnace for installation in a residential garage must be
installed so the burner(s) and the ignition source are located not less
than 18 inches (46 cm) above the floor, and the furnace must be located
or protected to avoid physical damage by vehicles.
If a matching cooling coil is used, it may be placed directly on the fur-
nace outlet and sealed to prevent leakage. If thermoplastic evaporator
‘A’ coil drain pans are to be installed in the upflow/horizontal configura-
tion, then extra 2” minimum spacing may be needed to ensure against
drain pan distortion.
4
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
On all installations without a coil, a removable access panel is recom-
mended in the outlet duct such that smoke or reflected light would be
observable inside the casing to indicate the presence of leaks in the
heat exchanger. This access cover shall be attached in such a manner
as to prevent leaks.
FLOOR BASE AND DUCTWORK INSTALLATION -
DOWNFLOW
Installations on combustible material or directly on any
floors must use a combustible floor base shown in Figure 8,
"Combustible Floor Base Accessory". Follow the instruc-
tions supplied with the combustible floor base accessory.
This combustible floor base can be replaced with a match-
ing cooling coil, properly sealed to prevent leaks. Follow the
instructions supplied with the cooling coil cabinet for install-
ing the cabinet to the duct connector. Plug intake and vent
pipe holes in bottom panel and move grommet to desired
vent side exit.
The duct system must be properly sized to obtain the correct airflow
for the furnace size that is being installed.
Refer to Table 6, "Ratings & Physical / Electrical Data" or the fur-
nace rating plate for the correct rise range and static pressures.
If the ducts are undersized, the result will be high duct static pres-
sures and/or high temperature rises which can result in a heat
exchanger OVERHEATING CONDITION. This condition can result
in premature heat exchanger failure, which can result in personal
injury, property damage, or death.
Downflow Air Conditioning Coil Cabinet
The furnace should be installed with coil cabinet part number specifi-
cally intended for downflow application. If a matching cooling coil is
used, it may be placed directly on the furnace outlet and sealed to pre-
vent leakage. For details of the coil cabinet dimensions and installation
requirements, refer to the installation instructions supplied with the coil
cabinet.
DUCT FLANGES
Four flanges are provided to attach ductwork to the furnace. These
flanges are rotated down for shipment. In order to use the flanges,
remove the screw holding an individual flange, rotate the flange so it is
in the upward position and reinstall the screw then repeat this for all 4
flanges.
Attach the air conditioning coil cabinet to the duct connector, and then
position the furnace on top of the coil cabinet. The connection to the fur-
nace, air conditioning coil cabinet, duct connector, and supply air duct
must be sealed to prevent air leakage.
If the flanges are not used, they must remain in the rotated down posi-
tion as shipped.
COIL INSTALLATION
Factory
installed
For duct attachment,
if needed.
On all installations without a coil, a removable access panel is rec-
ommended in the outlet duct such that smoke or reflected light
would be observable inside the casing to indicate the presence of
leaks in the heat exchanger. This access cover shall be attached in
such a manner as to prevent leaks.
COIL/FURNACE ASSEMBLY - MC/FC/PC SERIES
COILS
FIGURE 1: Duct Attachment
DUCTWORK INSTALLATION AND SUPPLY PLENUM
CONNECTION - UPFLOW/HORIZONTAL
Attach the supply plenum to the furnace outlet. The use of
an approved flexible duct connector is recommended on all
installations. This connection should be sealed to prevent
air leakage. The sheet metal should be crosshatched to
eliminate any popping of the sheet metal when the indoor
fan is energized.
UPFLOW
DOWNFLOW
FIGURE 2: Vertical Applications
FURNACE ASSEMBLY - MC & FC SERIES COILS
These coils are factory shipped for installation in either upflow or down-
flow applications with no conversion.
Position the coil casing over or under the furnace opening as shown in
Figure 2, "Vertical Applications" after configuring coil flanges as
required see “Coil Flange” section below.
Johnson Controls Unitary Products
5
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
COIL FLANGE INSTALLATION
The coils include removable flanges to allow proper fit up with furnaces
having various inlet and outlet flange configurations. The two flanges
are attached to the top of the coil in the factory during production. For
proper configuration of flanges refer to Figure 3, "Coil Flange".
Do not drill any holes or drive any screws into the front duct
flange on the coil in order to prevent damaging coil tubing. See
Figure 6, "PC Series Upflow Coil Installation"
C
(Min)
D
Flexible
Duct Collar
FACTORY
FLANGE
LOCATION
(Used for upflow
or horizontal
Field
Fabricated
Ductwork
Do not drill
or Screw
this flange
right installations)
ALTERNATE
FLANGE LOCATION
Upflow
Coil
(Used for downflow or
horizontal left installations)
Upflow
Furnace
FIGURE 3: Coil Flange
Alternate
Drain Location
Primary
Drain
Secondary
Drain
FURNACE ASSEMBLY - MC SERIES COILS ONLY
MC coils are supplied ready to be installed in a horizontal position. A
horizontal pan is factory installed. MC coils should be installed in all hor-
izontal applications with the horizontal drain pan side down.
FIGURE 6: PC Series Upflow Coil Installation
Table 2: Coil Projection Dimensions - PC Series Coils
Mounting Plate
COIL SIZE
DIMENSION “C” INCH
PC18
PC24
3-1/2
4-1/2
4-1/2
5-1/2
6-1/2
9
PC30, PC32, PC35
PC42, PC43, PC36, PC37
PC48
Furnace
PC60
NOTE: Dimension “C” should be at least 2/3 of dimension “D”. See Fig-
FIGURE 4: Horizontal Right Application
ure 6, "PC Series Upflow Coil Installation"
For horizontal left hand applications no conversion is required to an MC
coil when used with a downflow/horizontal furnace. A mounting plate,
supplied with every coil should always be installed on the side desig-
nated as top side. See Figures 4 & 5.
CRITICAL COIL PROJECTION
The coil assembly must be located in the duct such that a minimum dis-
tance is maintained between the top of the coil and the top of the duct.
Refer to Table 6.
Mounting Plate
COIL / FURNACE ASSEMBLY - HC SERIES COILS
These coils are supplied ready to be installed in a right hand position or
a left hand position. When used in conjunction with a horizontal furnace
(blow through) application, the coil should be oriented with the opening
of the “A” coil closest to the furnace. See Figure 6.
Furnace
NOTE: Each coil is shipped with an external tie plate that should be
used to secure the coil to the furnace. It should be installed on the back
side of the coil using the dimpled pilot holes. See Figure 6.
FIGURE 5: Horizontal Left Application
FURNACE ASSEMBLY - PC SERIES COILS
These upflow coils are designed for installation on top of upflow fur-
Use tie plate
supplied with coil
naces only.
If the coil is used with a furnace of a different size, use a 45° transition
to allow proper air distribution through the coil.
1. Position the coil casing over the furnace opening as shown in Fig-
ure 6, "PC Series Upflow Coil Installation".
2. Place the ductwork over the coil casing flange and secure.
Gas Furnace
3. Check for air leakage between the furnace and coil casing and
seal appropriately.
FIGURE 7: Horizontal Left or Right application (Right Shown)
6
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
DOWNFLOW DUCT CONNECTORS
ATTIC INSTALLATION
All downflow installations must use a suitable duct connector approved
by the furnace manufacturer for use with this furnace. The duct connec-
tors are designed to be connected to the rectangular duct under the
floor and sealed. Refer to the instructions supplied with the duct con-
nector for proper installation. Refer to the separate accessory parts list
at the end of these instructions for the approved accessory duct con-
nectors.
Line contact only permissible
between lines formed by the
intersection of furnace top
and two sides and building
joists, studs or framing
Supply
Air
Vent (Maintain
required
clearances to
combustibles)
Filter rack
must be a minimum
distance
Sheet metal in
front of furnace
combustion air
Openings is
Gas Piping
of 18” (45.7 cm)
from the
furnace
12”
Recommended
12”
FURNACE
30” MIN.
Work Area
Return
Air
WARM AIR PLENUM
WITH 1” FLANGES
Sediment
Trap
FIGURE 10: Typical Attic Installation
FIBERGLASS
INSULATION
This appliance is certified for line contact when the furnace is installed
in the horizontal left or right position. The line contact is only permissible
between lines that are formed by the intersection of the top and two
sides of the furnace and the building joists, studs or framing. This line
may be in contact with combustible material. Refer to Figure 10, "Typi-
cal Attic Installation".
FIBERGLASS TAPE
UNDER FLANGE
COMBUSTIBLE FLOOR
BASE ACCESSORY
When a furnace is installed in an attic or other insulated space,
keep all insulating materials at least 12 inches (30.5 cm) away from
furnace and burner combustion air openings.
SUSPENDED FURNACE / CRAWL SPACE
INSTALLATION
FIGURE 8: Combustible Floor Base Accessory
The furnace can be hung from floor joists or installed on suitable blocks
or pad. Blocks or pad installations shall provide adequate height to
ensure the unit will not be subject to water damage. Units may also be
suspended from rafters or floor joists using rods, pipe angle supports or
straps. Angle supports should be placed at the supply air end and near
the blower deck. Do not support at return air end of unit. All four sus-
pension points must be level to ensure quite furnace operation. When
suspending the furnace use a secure platform constructed of plywood
or other building material secured to the floor joists. Refer to for typical
crawl space installation.
RESIDENTIAL AND MODULAR HOME UPFLOW
RETURN PLENUM CONNECTION
Return air may enter the furnace through the side(s) or bottom depend-
ing on the type of application. Return air may not be connected into the
rear panel of the unit.
BOTTOM RETURN AND ATTIC INSTALLATIONS
Bottom return applications normally pull return air through a base plat-
form or return air plenum. Be sure the return platform structure or return
air plenum is suitable to support the weight of the furnace.
The internal bottom panel must be removed for this application.
Attic installations must meet all minimum clearances to combustibles
and have floor support with required service accessibility.
HORIZONTAL APPLICATION
Support
Angle Iron
Bracket
Bracket
6” Min. Between
Rod & Front of Furnace
Rod & Back of Furnace
1” Max. Between
FIGURE 9: Horizontal Application
FIGURE 11: Typical Suspended Furnace / Crawl Space Installation
This furnace may be installed in a horizontal position on either side
as shown above. It must not be installed on its back.
Johnson Controls Unitary Products
7
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
RIGHT SIDE
Combustion Air Inlet
LEFT SIDE
Combustion Air Inlet
FRONT
Condensate Drain
(Downflow)
Gas Pipe
Entry
Gas Pipe
Entry
Condensate Drain
(Downflow)
Vent Outlet
Electrical
Entry
Electrical
Entry
Vent Outlet
23”
Condensate
Drain
33
Condensate
Drain
Thermostat
Wiring
Thermostat
Wiring
Optional Return Air
Cutout (Either side)
14”
1”
28.5”
29.5”
(For Cladded door add appoximately an additional .75”)
A
1.5”
.56”
23.8”
3”
Vent
Outlet
Combustion
Air Inlet
B
B
C
.56”
24.25”
.56”
20”
RETURN END
SUPPLY END
FIGURE 12: Dimensions
Table 3: Cabinet and Duct Dimensions
Approximate
Operating Weights
Cabinet Dimensions (Inches)
Nominal
CFM (m3/min)
BTUH (kW)
Input
Cabinet
Size
A
A (cm)
36.8
36.8
44.4
44.4
53.3
53.3
53.3
53.3
62.2
62.2
62.2
B
B (cm)
34.0
34.0
41.6
41.6
50.5
50.5
50.5
50.5
59.4
59.4
59.4
C
C (cm)
29.8
Lbs
113
118
122
126
136
139
142
145
153
156
160
40 (11.7)
60 (17.6)
60 (17.6)
80 (23.4)
80 (23.4)
80 (23.4)
100 (29.3)
100 (29.3)
120 (35.1)
120 (35.1)
130 (38.1)
800 (22.7)
1000 (28.3)
1200 (34.0)
1200 (34.0)
1600 (45.3)
2200 (62.3)
1600 (45.3)
2000 (56.6)
1600 (45.3)
2000 (56.6)
2000 (56.6)
A
A
B
B
C
C
C
C
D
D
D
14 1/2
14 1/2
17 1/2
17 1/2
21
13 3/8
13 3/8
16 3/8
16 3/8
19 7/8
19 7/8
19 7/8
19 7/8
23 3/8
23 3/8
23 3/8
11 3/4
11 3/4
13 1/4
14 3/4
16 1/2
16 1/2
18 1/4
18 1/4
21 3/4
21 3/4
No Hole
29.8
33.7
37.5
41.9
21
41.9
21
46.4
21
46.4
24 1/2
24 1/2
24 1/2
55.2
55.2
No Hole
SECTION III: FILTERS
Table 4: Recommended Filter Sizes (High Velocity 600 FPM)
FILTER INSTALLATION
All applications require the use of a field installed filter. All filters and
mounting provision must be field supplied.
CFM
(m³/min)
Cabinet
Size
A
Side
(in)
Bottom
(in)
800 (22.7)
1000 (28.3)
1200 (34.0)
1200 (34.0)
1600 (45.3)
1600 (45.3)
2000 (56.6)
2200 (62.3)
2000 (56.6)
16 x 25
16 x 25
16 x 25
16 x 25
16 x 25
16 x 25
(2) 16 x 25
(2) 16 x 25
(2) 16 x 25
14 x 25
14 x 25
14 x 25
16 x 25
16 x 25
20 x 25
20 x 25
20 x 25
22 x 25
A
Filters must be installed external to the furnace cabinet. DO NOT
attempt to install filters inside the furnace.
A
B
NOTE: Single side return above 1800 CFM is approved as long as the
filter velocity does not exceed filter manufacturer’s recommendation
and a transition is used to allow use on a 20x25 filter.
B
C
C
C
D
NOTES:
1. Air velocity through throwaway type filters may not exceed 300 feet per
minute (91.4 m/min). All velocities over this require the use of high velocity
filters.
2. Do not exceed 1800 CFM using a single side return and a 16x25 filter. For
CFM greater than 1800, you may use two side returns or one side and the
bottom or one side return with a transition to allow use of a 20x25 filter.
8
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
SIDE RETURN
Locate the “L” shaped corner locators. These indicate the size of the cut-
out to be made in the furnace side panel. Refer to Figure 13, "Side
Return Cutout Markings".
Outlet
Pressure
Port
Vent Port
Outlet
Inlet
Wrench
Boss
Front of
Furnace
Inlet
Pressure
Port
Main Regulator
Adjustment
On/Off Switch
(Shown in ON position)
Side of
Furnace
FIGURE 14: Gas Valve
Corner
Markings
FIGURE 13: Side Return Cutout Markings
Plan your gas supply before determining the correct gas pipe entry.
Use 90-degree service elbow(s), or short nipples and conventional
90-degree elbow(s) to enter through the cabinet access holes.
Install the side filter rack following the instructions provided with that
accessory. If a filter(s) is provided at another location in the return air
system, the ductwork may be directly attached to the furnace side
panel.
GAS PIPING INSTALLATION
Properly sized wrought iron, approved flexible or steel pipe must be
used when making gas connections to the unit. If local codes allow the
use of a flexible gas appliance connection, always use a new listed con-
nector. Do not use a connector that has previously serviced another gas
appliance.
Some accessories such as electronic air cleaners and pleated
media may require a larger side opening. Follow the instructions
supplied with that accessory for side opening requirements. Do not
cut the opening larger than the dimensions shown in Figure 12,
"Dimensions".
Some utility companies or local codes require pipe sizes larger than the
minimum sizes listed in these instructions and in the codes. The furnace
rating plate and the instructions in this section specify the type of gas
approved for this furnace - only use those approved gases. The instal-
lation of a drip leg and ground union is required. Refer to Figure 15,
"Upflow/Downflow Gas Piping".
HORIZONTAL APPLICATION
Horizontal Filters
External Manual
Shutoff Valve
All filters and mounting provision must be field supplied. All installa-
tions must have a filter installed.
To Gas
Supply
To Gas
Supply
Any branch duct (rectangular or round duct) attached to the plenum
must attach to the vertical plenum before the filter. The use of straps
and / or supports is required to support the weight of the external filter
box.
Downflow Filters
Grounded Joint Union
may be Installed
Inside or Outside Unit.
Drip Leg
Downflow furnaces typically are installed with the filters located above
the furnace, extending into the return air plenum or duct. Any branch
duct (rectangular or round duct) attached to the plenum must attach to
the vertical plenum above the filter height.
FIGURE 15: Upflow/Downflow Gas Piping
Filter(s) may be located in the duct system external to the furnace using
an external duct filter box attached to the furnace plenum or at the end
of the duct in a return filter grille(s). The use of straps and/or supports is
required to support the weight of the external filter box.
Manual
Shut-off
Valve
Drip
Leg
Gas
Pipe
SECTION IV: GAS PIPING
Gas Burners
Gas Valve
GAS SAFETY
Gas
Pipe
An overpressure protection device, such as a pressure regulator,
must be installed in the gas piping system upstream of the furnace
and must act to limit the downstream pressure to the gas valve so it
does not exceed 0.5 PSI (14" w.c. (3.48 kPa). Pressures exceeding
0.5 PSI (14” w.c. (3.48 kPa) at the gas valve will cause damage to
the gas valve, resulting in a fire or explosion or cause damage to
the furnace or some of its components that will result in property
damage and loss of life.
Drip
Leg
Manual
Shut-off Valve
FIGURE 16: Horizontal Gas Piping
An accessible manual shutoff valve must be installed upstream of
the furnace gas controls and within 6 feet (1.8 m) of the furnace.
Johnson Controls Unitary Products
9
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
The furnace must be isolated from the gas supply piping system by
closing its individual external manual shutoff valve during any pressure
testing of the gas supply piping system at pressures equal to or less
than 1/2 psig (3.5 kPa).
GAS ORIFICE CONVERSION FOR PROPANE (LP)
This furnace is constructed at the factory for natural gas-fired operation,
but may be converted to operate on propane (LP) gas by using a fac-
tory-supplied LP conversion kit. Follow the instructions supplied with
the LP kit.
HIGH ALTITUDE GAS ORIFICE CONVERSION
This furnace is constructed at the factory for natural gas-fired operation
at 0 –5,000 feet (0-m – 1,524 m) above sea level.
The gas valve body is a very thin casting that cannot take any
external pressure. Never apply a pipe wrench to the body of the gas
valve when installing piping. A wrench must be placed on the octa-
gon hub located on the gas inlet side of the valve. Placing a wrench
to the body of the gas valve will damage the valve causing improper
operation and/or the valve to leak.
The manifold pressure must be changed in order to maintain proper
and safe operation when the furnace is installed in a location where the
altitude is greater than 5,000 feet (1,524 m) above sea level. Refer to
Table 5, "Nominal Manifold Pressure - High Fire" for proper manifold
pressure settings.
Gas piping may be connected from either side of the furnace using any
of the gas pipe entry knockouts on both sides of the furnace. Refer to
Figure 12, "Dimensions".
HIGH ALTITUDE PRESSURE SWITCH CONVERSION
For installation where the altitude is less than 5,000 feet (1,524m), it is
not required that the pressure switch be changed unless you are in an
area subject to low pressure inversions.
Table 5: Nominal Manifold Pressure - High Fire
Manifold Pressures (in wc)
Manifold Pressures (kpa)
Altitude (feet)
Altitude (m)
0-7999
3.5
8000-8999
3.5
9000-9999
3.5
0-2437
0.87
0.87
0.87
0.87
0.87
0.87
0.80
2.44
2438-2742
0.87
2743-3048
0.87
800
850
29.8
31.7
3.5
3.5
3.5
0.87
0.87
900
3.5
3.5
3.5
33.5
0.87
0.87
950
3.5
3.5
3.3
35.4
0.87
0.81
1000
1050
1100
3.5
3.2
2.9
37.3
0.80
0.73
3.5
2.9
2.7
39.1
0.73
0.67
3.2
2.7
2.4
41.0
0.66
0.61
2500 (LP)
9.8
8.2
7.5
93.2 (LP)
2.03
1.86
PROPANE AND HIGH ALTITUDE CONVERSION KITS
It is very important to choose the correct kit and/or gas orifices for the altitude and the type of gas for which the furnace is being installed.
Only use natural gas in furnaces designed for natural gas. Only use propane (LP) gas for furnaces that have been properly converted to use pro-
pane (LP) gas. Do not use this furnace with butane gas.
Incorrect gas orifices or a furnace that has been improperly converted will create an extremely dangerous condition resulting in premature heat
exchanger failure, excessive sooting, high levels of carbon monoxide, personal injury, property damage, a fire hazard and/or death.
High altitude and propane (LP) conversions are required in order for the appliance to satisfactory meet the application.
An authorized distributor or dealer must make all gas conversions.
In Canada, a certified conversion station or other qualified agency, using factory specified and/or approved parts, must perform the conversion.
The installer must take every precaution to insure that the furnace has been converted to the proper gas orifice size when the furnace is installed.
Do not attempt to drill out any orifices to obtain the proper orifice size. Drilling out a gas orifice will cause misalignment of the burner flames,
causing premature heat exchanger burnout, high levels of carbon monoxide, excessive sooting, a fire hazard, personal injury, property damage
and/or death.
SECTION V: ELECTRICAL POWER
ELECTRICAL POWER CONNECTIONS
Use copper conductors only.
Field wiring to the unit must be grounded. Electric wires that are field
installed shall conform to the temperature limitation for 63°F (35°C) rise
wire when installed in accordance with instructions. Refer to Table 6,
"Ratings & Physical / Electrical Data" in these instructions for specific
furnace electrical data.
10
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
Table 6: Ratings & Physical / Electrical Data
Nominal
Airflow
Max. Outlet
Air Temp
Max
Min. wire Size
Input
MBH
Output
Air Temp. Rise
Total Unit AFUE
Over-Current (awg) @ 75 ft
Amps
%
m3/min
Protect
one way
kW
MBH
kW
CFM
800
°F
°C
°F
°C
40
60
11.7
17.6
17.6
23.4
23.4
23.4
29.3
29.3
35.1
35.1
38.1
38
57
11.1
16.7
16.7
22.3
22.3
22.3
27.8
27.8
33.4
33.4
36.2
22.7
28.3
34.0
34.0
45.3
62.3
45.3
56.6
45.3
56.6
56.6
8.0
95.5
95.5
95.5
95.5
95.5
95.5
95.5
95.5
95.5
95.5
95.5
30-60
30-60
30-60
35-65
35-65
35-65
35-65
35-65
40-70
35-65
45-75
17-33
19-36
19-36
19-36
19-36
19-36
19-36
19-36
22-39
19-36
28-44
15
15
15
15
15
20
15
20
15
20
20
14
14
14
14
14
12
14
12
14
12
12
155
155
160
165
155
155
165
155
170
160
165
68.3
68.3
71.1
73.9
68.3
68.3
73.9
68.3
76.7
71.1
73.9
1000
1200
1200
1600
2200
1600
2000
1600
2000
2000
10.0
10.0
10.0
11.5
17.0
11.5
17.0
11.5
17.0
17.0
60
57
80
76
80
76
80
76
100
100
120
120
130
95
95
114
114
123.5
Annual Fuel Utilization Efficiency (AFUE) numbers are determined in accordance with DOE Test procedures.
Wire size and over current protection must comply with the National Electrical Code (NFPA-70-latest edition) and all local codes.
The furnace shall be installed so that the electrical components are protected from water.
SUPPLY VOLTAGE CONNECTIONS
The power connection leads and wiring box may be relocated to the
left side of the furnace. Remove the screws and cut wire tie holding
excess wiring. Reposition on the left side of the furnace and fasten
using holes provided.
Junction
Box
LOW VOLTAGE CONTROL WIRING CONNECTIONS
Connect ground
lead to screw
Install the field-supplied thermostat by following the instructions that
come with the thermostat. With the thermostat set in the OFF position
and the main electrical source disconnected, connect the thermostat
wiring from the wiring connections on the thermostat to the terminal
board on the ignition module, as shown in Figure 18, "Thermostat Chart
- Single Stage AC with Single Stage PSC Furnaces". Electronic thermo-
stats may require the common wire to be connected. Apply strain relief
to thermostat wires passing through cabinet. If air conditioning equip-
ment is installed, use thermostat wiring to connect the Y and C termi-
nals on the furnace control board to the proper wires on the condensing
unit (unit outside).
Electrical Entry
BLK
L1-Hot
Neutral
WHT
FIGURE 17: Electrical Wiring
1. Provide a power supply separate from all other circuits. Install
overcurrent protection and disconnect switch per local/national
electrical codes. The switch should be close to the unit for conve-
nience in servicing. With the disconnect or fused switch in the OFF
position, check all wiring against the unit wiring label. Refer to the
wiring diagram in this instruction.
Set the heat anticipator in the room thermostat to 0.4 amps. Setting
it lower will cause short cycles. Setting it higher will cause the room
temperature to exceed the set points.
2. Remove the screws retaining the wiring box cover. Route the
power wiring through the opening in the unit into the junction box
with a conduit connector or other proper connection. In the junc-
tion box there will be 3 wires, a Black Wire, a White Wire. Connect
the power supply as shown on the unit-wiring label on the inside of
the blower compartment door or the wiring schematic in this sec-
tion. The black furnace lead must be connected to the L1 (hot)
wire from the power supply. The white furnace screw must be con-
nected to neutral. Connect the power supply ground to the green
screw (equipment ground) An alternate wiring method is to use a
field provided 2” (5.1 cm) x 4” (10.2 cm) box and cover on the out-
side of the furnace. Route the furnace leads into the box using a
protective bushing where the wires pass through the furnace
panel. After making the wiring connections replace the wiring box
cover and screws. Refer to Figure 17, "Electrical Wiring".
Some electronic thermostats do not have adjustable heat anticipa-
tors. They should be set to six cycles per hour. Follow the thermo-
stat manufacturer's instructions.
The 24-volt, 40 VA transformer is sized for the furnace components
only, and should not be connected to power auxiliary devices such as
humidifiers, air cleaners, etc. The transformer may provide power for an
air conditioning unit contactor.
3. The furnace's control system requires correct polarity of the power
supply and a proper ground connection. Refer to Figure 17, "Elec-
trical Wiring"
Johnson Controls Unitary Products
11
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
the Product Catalog Section.
AC 5D
Single Stage Air Conditioner – Single Stage PSC Furnace
ID MODELS
G*(8/9)S
GF(8/9)
G*9F
LF8
L(Y/M)8S
G8C
(G,T)G(8/9)S
(G/T)GLS
THERMOSTAT
SINGLE STAGE
SINGLE STAGE
AIR
*PP11C70224
PSC
FURNACE
CONDITIONER
SINGLE STAGE PSC
FURNACE
SINGLE STAGE
AIR CONDITIONER
1
C
C
24 – Volt Common
24 – Volt Common
Y
Y/Y2
Y
Full Stage Compressor
Full Stage Compressor
CompressorContactor
RH
R
24 – Volt Hot
(Heat XFMR)
24 – Volt Hot
G
G
Fan
Fan
W
Full Stage Heat
RC
24 – Volt Hot
(Cool XFMR)
W
Full Stage Heat
24VAC Humidifier
(Optional)
HM1
Humidistat
Clipping Jumper W914 for
electric heat on thermostat
is not necessary
Other Part Numbers:
1
SAP
=
Legacy
265901 = 031-09166
FIGURE 18: Thermostat Chart - Single Stage AC with Single Stage PSC Furnaces
12
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
HP 2C
Single Stage Heat Pump – Single Stage PSC Furnace
ID MODELS
OD MODELS
G*(8/9)S
GF(8/9)
E*R*
*RHS
G*9F
LF8
E*ZD
E*B*
HP*
L(Y/M)8S
G8C
(G,T)G(8/9)S
(G/T)GLS
*HGD
THERMOSTAT
THERMOSTAT
THERMOSTAT
*BP21H50124
*BN21H00124
*DP21H40124
*DN21H00124
SINGLE STAGE
PSC
FURNACE
SINGLE STAGE
HEAT PUMP
*DN22U00124
*DP32H70124
SINGLE STAGE PSC
FURNACE
2
DEMAND DEFROST
CONTROL
1
C
C
C
24 – Volt Common
24 – Volt Common
24 – Volt Common
Y1
Y/Y2
Y
First Stage Compressor
Full Stage Compressor
Compressor
R
R
R
24 – Volt Hot
24 – Volt Hot
24 – Volt Hot
G
G
Fan
Fan
E
W
W1/66(out)
Heat
Emergency Heat
Full Stage Heat
W2
N/A
N/A
Third Stage Heat
O
O
Reversing Valve
Energized in Cool
Reversing Valve
Energized in Cool
L
X/L
Malfunction Light
Malfunction Light
Y2
Second Stage Compressor
W1
W
Second Stage Aux. Heat
Auxiliary Heat
3
External Humidistat
(Optional)
Open on Humidity Rise
24VAC Humidifier
(Optional)
Step 1 of Thermostat
Installer / Configuration
Menu must be set to
Heat Pump 1
Step 9 of Thermostat
Installer / Configuration
Menu must be set to
Pump OFF
Other Part Numbers:
Part Numbers:
3
1
Part Number:
S1-2HU16700124
2
SAP
=
Legacy
SAP
=
Legacy
265901 = 031-09166
67297 = 031-01975
FIGURE 19: Thermostat Chart - Single Stage HP with Single Stage PSC Furnaces
Johnson Controls Unitary Products
13
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
ACCESSORY CONNECTIONS
Vent Pipe
The furnace control will allow power-switching control of various acces-
sories.
ELECTRONIC AIR CLEANER CONNECTION
Two 1/4” (0.64 cm) spade terminals (EAC and NEUTRAL) for electronic
air cleaner connections are located on the control board. The terminals
provide 115 VAC (1.0 amp maximum) during circulating blower opera-
tion.
Gas Supply
(Both sides)
Electrical
Supply
HUMIDIFIER CONNECTION
Two 1/4” (0.64 cm) spade terminals (HUM and NEUTRAL) for humidi-
fier connections are located on the control board. The terminals provide
115 VAC (1.0 amp maximum) during heating system operation.
1 Coil for
Each Furnace
Supply
Air
A mounting hole is provided on the control panel next to the furnace
control board for mounting a humidifier transformer if required.
FIGURE 20: Typical Twinned Furnace Application
SECTION VI: TWINNING AND STAGING
In applications where more heating capacity or more airflow capacity is
needed than what one furnace can deliver, twinning can be used to
make two furnaces operate in tandem. When two furnaces are installed
using the same duct system, it is very important that the two furnace cir-
culating air blowers operate in unison. If one blower starts before the
second blower, the duct system will become pressurized and the blower
on the second furnace will turn backwards causing the second furnace
to overheat, resulting in damage to the furnace. Twinning is used to
make two furnaces operate in tandem, using one duct system, one
room thermostat and causing both furnaces to turn on and off simulta-
neously.
When two furnaces are twinned, typical system total airflow will be
approximately 85% of additive individual furnaces, i.e., two 2000
CFM units will yield a total 3400 CFM.
If a return duct is connected to only one furnace (with a connection
between the two furnaces) an imbalance in the airflow will occur
and the furnace furthest from the return plenum will overheat.
GAS PIPING
Before installing the relay and wiring, disconnect electrical power to
both furnaces. Failure to cut power could result in electrical shock
or equipment damage.
Furnace gas supplies must be provided as specified with these instruc-
tions. Since the furnaces are side by side, with no space between, gas
supplies must enter on the right and left respectively. All gas piping
must be in accordance with the national fuel gas code, ANSI Z223.1,
latest edition, and/or all local code or utility requirements.
TWINNING
The relay must not be installed in any location where it could be
exposed to water. If the relay has been exposed to water in any
way, it must not be used.
In applications where more heating capacity or more airflow capacity is
needed than what one furnace can deliver, twinning can be used to
make two furnaces operate in tandem, using one duct system and one
room thermostat. When one duct system is used for two furnaces, it is
necessary that the two blowers operate in unison. The twinning function
of the board in this furnace ensures that both blowers turn on and off
simultaneously, and operate on the same blower speed.
TWINNING DUCT SYSTEM
Twinned furnaces must only be applied on a common duct system. A
single air supply plenum must be used for both furnaces and coil(s).
Separate plenums and supply ducts systems cannot be utilized. A sin-
gle return air plenum, common to both furnaces must be used. It is sug-
gested that a return platform be utilized, with bottom air entrance into
each furnace. If a side entrance returns system is used, the common
return duct must be divided equally so as to supply each furnace with
an equal amount of return air.
Single-Wire Twinning
The control in the furnace has the single-wire twinning feature. With this
feature, a single wire is connected between the TWIN terminal on one
furnace board to the TWIN terminal on the second furnace board. The
board then communicates the blower status from one furnace to the
other along this wire. This communication makes the second furnace
blower come on at the same time, and on the same speed, as the first
furnace blower.
Both furnaces must be identical models in both heating capacity and
CFM capacity. Both furnaces must be operated on the same motor
speed tap. See typical application, Figure 20, "Typical Twinned Furnace
Application".
Single-Wire Twinning Instructions
If furnace staging is desired with two single stage furnaces on a com-
mon duct, where the gas burner on the first furnace operates on W1
and the gas burner on the second furnace operates on W2, then the
use of an air-mixing device in the plenum to mix the air from both fur-
naces is strongly recommended. The mixing device must be installed
before any ducts that supply air to occupied spaces. Twinning causes
both indoor fans to operate simultaneously. If a mixing device is not
used, any ducts that are connected down stream from the furnace that
operates on W2, will be supplying cold air in the Heating mode to the
occupied spaces unless W2 is energized.
Connect the control wiring as shown in Figure 21, "Single Stage Twin-
ning Wiring Diagram".
1. Connect the low voltage wiring from the wall thermostat to the ter-
minal strip on the control board of Furnace #1.
2. Connect a wire from the TWIN terminal of Furnace #1 to the TWIN
terminal of Furnace #2.
3. Install a separate 24V relay as shown in the diagram below. Use of
this relay is required, as it ensures that the transformers of the two
furnaces are isolated, thus preventing the possibility of any safety
devices being bypassed.
14
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
Single-Wire Twinning Operation
Single-Wire Staging Instructions
Heating - On a call for heat (W signal) from the wall thermostat, both
furnaces will start the ignition sequence and the burners on both fur-
naces will light. About thirty seconds after the burners light, the blowers
on both furnaces will come on in heating speed. When the thermostat is
satisfied, the burners will all shut off and, after the selected blower off
delay time, both blowers will shut off at the same time. The twinning
control ensures that both blowers come on and shut off at the same
time.
Connect the control wiring as shown in Figure 22, "Two-Stage Twinning
Wiring Diagram".
1. Connect the low voltage wiring from the wall thermostat to the ter-
minal strip on the control board of Furnace #1. For staging applica-
tions, the wire from thermostat W1 is connected to the W
connection on the board on Furnace #1. The wire from thermostat
W2 is connected to Furnace #2 through a separate relay, as
described below.
Cooling - On a call for cooling (Y signal) from the wall thermostat, both
furnace blowers will come on at the same time in cooling speed. When
the thermostat is satisfied, both blowers will stay on for 60 seconds,
then will shut off at the same time.
Continuous Fan - On a thermostat call for continuous fan (G signal),
both furnace blowers will come on at the same time in cooling speed
and will stay on until the G signal is removed.
2. Connect a wire from the TWIN terminal of Furnace #1 to the TWIN
terminal of Furnace #2.
3. Install a separate 24V relay as shown in the diagram below. Use of
this relay is required, as it ensures that the transformers of the two
furnaces are isolated, thus preventing the possibility of any safety
devices being bypassed.
Single-Wire Staging Operation
FURNACE 2
CONTROL BOARD
FURNACE 1
CONTROL BOARD
Heating - On a call for first-stage heat (W1 signal) from the wall thermo-
stat, Furnace #1 will start the ignition sequence and the burners will
light. About thirty seconds after the burners light, the blowers on both
furnaces will come on in heating speed. When the thermostat is satis-
fied, the burners will shut off and, after the selected blower off delay
time, both blowers will shut off at the same time. On a call for second
stage of heat, the burners of Furnace #2 will also light and both blowers
will run. The twinning control ensures that both blowers come on and
shut off at the same time.
W
G
C
W
G
C
R
Y
TWIN
R
Y
TWIN
ISOLATION
RELAY
Cooling - On a call for cooling (Y signal) from the wall thermostat, both
furnace blowers will come on at the same time. When the thermostat is
satisfied, both blowers will stay on for 60 seconds, then will shut off at
the same time.
TO A/C
W
G
R
Y
Continuous Fan - On a thermostat call for continuous fan (G signal),
both furnace blowers will come on at the same time in cooling speed
and will stay on until the G signal is removed.
WALL THERMOSTAT
FIGURE 21: Single Stage Twinning Wiring Diagram
STAGING
FURNACE 2
CONTROL BOARD
FURNACE 1
CONTROL BOARD
This control can also be used along with a two-stage wall thermostat to
stage two twinned furnaces, making them operate like a single two-
stage furnace. This allows only one furnace to supply heat during times
when the heat output from one furnace is sufficient to satisfy the
demand. When one duct system is used for two furnaces, it is neces-
sary that the two blowers operate in unison. The twinning function of
this board ensures that both blowers turn on and off simultaneously,
and operate on the same blower speed. Even when only one furnace is
supplying heat, both furnace blowers must run.
W
G
C
W
G
C
R
Y
TWIN
R
Y
TWIN
ISOLATION
RELAY
Single-Wire Staging
The single-wire twinning feature of this board can also be used for stag-
ing of two furnaces. With this feature, a single wire is connected
between the TWIN terminal on one furnace board to the TWIN terminal
on the second furnace board. The board then communicates the blower
status from one furnace to the other along this wire. This communica-
tion makes the second furnace blower come on at the same time, and
on the same speed, as the first furnace blower.
TO A/C
W1
G
Y
W2
R
WALL THERMOSTAT
FIGURE 22: Two-Stage Twinning Wiring Diagram
Johnson Controls Unitary Products
15
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
SECTION VII: CONDENSATE PIPING AND
FURNACE VENTING CONFIGURATION
CONDENSATE DRAIN LOCATION
Condensate must be disposed of properly. Follow local plumbing or
wastewater codes. The drain line must maintain a 1/4" per foot
(0.635 cm per meter) downward slope to the drain.
As shipped from the factory:
•
For all 040, 060, & 080K input furnaces the main drain is plumbed
through the casing right-side opening when viewed from the front
of the furnace.
CONDENSATE DRAIN TERMINATION
A condensate sump pump MUST be used if required by local codes, or
if no indoor floor drain is available. The condensate sump pump must
be approved for use with acidic condensate.
•
For all 100, 120, & 130K input furnaces the main drain is plumbed
through the casing left-side opening when viewed from the front
of the furnace.
NOTE: On 130K BTU models, there is no provision for the vent to
exit the top of the cabinet, the vent must always exit one of the
sides.
DO NOT terminate condensate drain in a chimney, or where the
drain line may freeze. The line must terminate at an inside drain to
prevent freezing of the condensate and possible property damage.
DO NOT trap the drain line at any other location than at the conden-
sate drain trap supplied with the furnace.
NOTE: The Figures 23 - 26 show the condensate drain arrange-
ment for the various possible furnace and vent blower positions.
The condensate hoses must slope downwards at all points.
The condensate water will flow to the drain better id a tee with a short,
open end, length of pipe is installed in the drain line. The top of the pipe
should terminate at least to the middle of the condensate pan which is
located inside the furnace.
CONDENSATE DRAIN TRAP AND DRAIN FREEZE
PROTECTION
Special precautions MUST be made if installing furnace in an area
which may drop below freezing. This can cause improper operation or
damage to the equipment. If the furnace is installed in an area that has
the potential of freezing, the drain line must be protected. Use a 3 to 6
watt per foot at 115 vac, 40º F (4.4° C) self-regulating, shielded and
waterproof heat tape. Wrap the drain line outside of the furnace with the
heat tape and secure with ties. Follow the heat tape manufacturer's rec-
ommendations.
The furnace condensate pan is self priming and con-
tains an internal trap to prevent flue gas leaking. Do
not install an external condensate trap.
When drain hose routing changes are required (shown in Figures 23-
26), be sure to cap all un-used openings.
If rerouting hoses - excess length should be cut off so that no sagging
loops will collect and hold condensate - which will cause the furnace to
not operate.
No hose clamps are needed for connecting to the condensate pan.
Use only Propylene Glycol (RV anti-freeze) to winterize the furnace.
Refer to the manufacturer’s specification to ensure that it is compat-
ible with plastics and other components of the furnace. DO NOT
use Ethylene Glycol anti-freeze in the furnace.
The condensate drain from the furnace may be connected in com-
mon with the drain from an air conditioning coil if allowed by local
code.
16
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
For 040, 060 & 080K input furnaces, the condensate
drain is plumbed toward the right casing outlet from the factory.
.
f a c t o t h r y e f r o m o u t l e t c a t s i l n e g f t h e t o w a r d p l u i s m b e d d r a i n
c o n d t h e e n s a t e f u r n a c i n e p s u , t 1 3 & 0 K 1 2 0 1 0 0 , F o r
FIGURE 23: Upflow Configuration
Johnson Controls Unitary Products
17
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
FIGURE 24: Downflow Configuration
18
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
FIGURE 25: Horizontal Left Configuration
Johnson Controls Unitary Products
19
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
FIGURE 26: Horizontal Right Configuration
20
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
4. All combustion air and vent pipe must conform to American
National Standards Institute (ANSI) and American Society for Test-
ing and Materials (ASTM) standards D1785 (Schedule 40 PVC),
D2665 (PVC-DWV), F891 (PVC-DWV Cellular Core), D2261
(ABS-DWV) or F628 (Schedule 40 ABS). Pipe cement and primer
must conform to ASTM Standard D2546 (PVC) or D2235 (ABS). If
ABS pipe is to be used, any joint where ABS pipe is joined to PVC
pipe must be glued with cement that is approved for use with
BOTH materials. Metallic materials must not be used for venting or
air intake.
SECTION VIII: COMBUSTION AIR AND
VENT SYSTEM
COMBUSTION AIR AND VENT SAFETY
This Category IV, dual certified direct vent furnace is designed for resi-
dential application. It may be installed without modification to the con-
densate system in a basement, garage, equipment room, alcove, attic
or any other indoor location where all required clearance to combusti-
bles and other restrictions are met. The combustion air and the venting
system must be installed in accordance with Section 5.3, Air for Com-
bustion and Ventilation, of the National Fuel Gas Code Z223.1/NFPA 54
(latest edition), or Sections 7.2, 7.3 or 7.4 of CSA B149.1, National Gas
and Propane Codes (latest edition) or applicable provisions of the local
building code and these instructions.
5. If a flexible connector is used in the vent system, it must be made
of a material that is resistant to acidic exposure and to at least
225° F temperature. Flexible connectors are also allowed in the
combustion air pipe.
6. All models are supplied with 2" vent connections. When the pipe
must be increased to 3" diameter, the transition from 2" to 3" must
be done as close to the furnace as possible. For upflow models,
the transition from 2" to 3" should be done immediately above the
furnace. For downflow or horizontal models, the transition from 2"
to 3" pipe should be done immediately after exiting the furnace.
The “VENT SYSTEM” must be installed as specified in these
instructions for Residential and Non HUD Modular Homes. The
direct vent system is the only configuration that can be installed in a
Non HUD Modular Home.
7. In Canada, vents shall be certified to ULC S636, Standard for Type
BH Gas Venting Systems. IPEX System 636 PVC is certified to
this standard.
8. In Canada, the first three feet (900 mm) of the vent must be readily
accessible for inspection.
This furnace may not be common vented with any other appliance,
since it requires separate, properly sized air intake and vent lines.
The furnace shall not be connected to any type of B, BW or L vent
or vent connector, and not connected to any portion of a factory-
built or masonry chimney
9. For single pipe systems it is recommended to install the combus-
tion air coupling provided and install approximately 18” of PVC
pipe on the furnace.
10. Minimum vent length for all models is 5 feet.
The furnace shall not be connected to a chimney flue serving a sep-
arate appliance designed to burn solid fuel.
TABLE 7: Maximum Equivalent Pipe Length
Maximum
Equivalent
length feet (m)
Model Input
BTUH (kW)
Pipe Size
Inches (cm)
When combustion air pipe is installed above a suspended ceiling or
when it passes through a warm and humid space, the pipe must be
insulated with 1/2” Armaflex or other heat resistant type insulation if
two feet or more of pipe is exposed.
Vent piping must be insulated if it will be subjected to freezing tem-
peratures such as routing through unheated areas or through an
unused chimney.
40,000 (11.7)
40,000 (11.7)
60,000 (17.6)
60,000 (17.6)
80,000 (23.4)
80,000 (23.4)
100,000 (29.3)
100,000 (29.3)
120,000 (35.1)
120,000 (35.1)
130,000 (38.1)
2 (5.1)
3 (7.6)
2 (5.1)
3 (7.6)
2 (5.1)
3 (7.6)
2 (5.1)
3 (7.6)
2 (5.1)
3 (7.6)
3 (7.6)
65 (19.8)
90 (27.4)
65 (19.8)
90 (27.4)
65 (19.8)
90 (27.4)
30 (9.2)
COMBUSTION AIR/VENT PIPE SIZING
The size of pipe required will be determined by the furnace model, the
total length of pipe required and the number of elbows required.
90 (27.4)
30 (9.2)
90 (27.4)
85 (25.9)
Table 7, "Maximum Equivalent Pipe Length" lists the maximum equiva-
lent length of pipe allowed for each model of furnace. The equivalent
length of elbows is shown in Table 9, "Equivalent Length of Fittings".
The equivalent length of the vent system is the total length of straight
pipe PLUS the equivalent length of all of the elbows.
A
A
The following rules must also be followed:
1. Long radius (sweep) elbows are recommended. Standard elbows
may be used, but since they have a longer equivalent length, they
will reduce the total length of pipe that will be allowed. Short radius
(plumbing vent) elbows are not allowed. The standard dimensions
of the acceptable elbows are shown below.
2. The maximum equivalent length listed in Table 7, "Maximum
Equivalent Pipe Length" is for the vent piping and the air intake
piping separately. For example, if the table allows 65 equivalent
feet for a particular model, then the vent can have 65 equivalent
feet of pipe, AND the combustion air intake can have another 65
equivalent feet of pipe.
STANDARD ELBOW
FIGURE 27: Dimensions
TABLE 8: Elbow Dimensions
LONG (SWEEP) ELBOW
3. Three vent terminal elbows (two for the vent and one for the com-
bustion air intake) are already accounted for and need not be
included in the equivalent length calculation.
Elbow
"A" Dimension
2" Standard
3" Standard
2" Sweep
3" Sweep
2-5/16"
3-1/16"
3-1/4"
4-1/16"
Dimensions are those required in Standard ASTM D-3311.
Johnson Controls Unitary Products
21
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
TABLE 9: Equivalent Length of Fittings
Fitting
Equivalent Length
5 feet of 2" pipe
2-1/2 feet of 2" pipe
10 feet of 2" pipe
5 feet of 2" pipe
5 feet of 3" pipe
2-1/2 feet of 3" pipe
10 feet of 3" pipe
5 feet of 3" pipe
10 feet of 2" pipe
10 feet of 3" pipe
Accessory concentric vent / intake termination kits 1CT0302 and
1CT0303 are available and approved for use with these furnaces.
Horizontal sidewall vent terminations kits 1HT0901 & 1HT0902 are
also approved for use with these furnaces.
2" 90º sweep elbow
2" 45º sweep elbow
2" 90º standard elbow
2" 45º standard elbow
3" 90º sweep elbow
3" 45º sweep elbow
3" 90º standard elbow
3" 45º standard elbow
2" corrugated connector
3" corrugated connector
Furnace vent pipe connections are sized for 2” (5.1 cm). pipe. Any
pipe size change must be made outside the furnace casing in a ver-
tical pipe section to allow proper drainage of condensate. An offset
using two 45º (degree) elbows will be required for plenum clear-
ance when the vent is increased to 3” (7.6 cm).
COMBUSTION AIR AND VENT PIPING ASSEMBLY
Example:
The final assembly procedure for the combustion air and vent piping is
as follows:
An 80,000 BTUH furnace requires 32 feet of pipe and four 90º elbows.
Using 2" pipe and standard elbows, the total equivalent length will be:
1. Cut piping to the proper length beginning at the furnace.
2. Deburr the piping inside and outside.
32 feet of 2" pipe =
4 - 90º standard 2" elbows = (4x10) =
Total =
32 equivalent feet
40 equivalent feet
72 equivalent feet of 2" pipe
3. Chamfer (bevel) the outer edges of the piping.
4. Dry-fit the vent piping assembly from the furnace to the outside ter-
mination checking for proper fit support and slope.
This exceeds the 65 foot maximum equivalent length of 2" pipe allowed
for that model and is thus not acceptable.
5. Dry-fit the combustion air piping assembly checking for proper fit,
support and slope on the following systems:
By using sweep elbows, the total equivalent length will be:
a. Sealed combustion air systems from the furnace to the out-
side termination.
32 feet of 2" pipe =
4 - 90º standard 2" elbows = (4x5) =
Total =
32 equivalent feet
20 equivalent feet
52 equivalent feet of 2" pipe
b. Ventilated combustion air systems from the furnace to the
attic or crawl space termination.
This is less than the 65 foot maximum equivalent length of 2" pipe
allowed for that model and is thus acceptable.
Alternatively, using 3" pipe and standard elbows, the total equivalent
length will be:
Solvent cements are flammable and must be used in well-ventilated
areas only. Keep them away from heat, sparks and open flames.
Do not breathe vapors and avoid contact with skin and eyes.
32 feet of 3" pipe =
4 - 90º standard 2" elbows = (4x5) =
Total =
32 equivalent feet
40 equivalent feet
72 equivalent feet of 3" pipe
6. Disassemble the combustion air and vent piping, apply cement
primer and the cement per the manufactures instructions. Primer
and cement must conform to ASTM D2564 for PVC, or ASTM
D2235 for ABS piping.
This is less than the 90 foot maximum equivalent length of 3" pipe
allowed for that model and is thus acceptable.
TABLE 10: Combustion Air Intake and Vent Connection Size at Furnace
7. All joints must provide a permanent airtight and watertight seal.
(All Models)
8. Support the combustion air and vent piping such that it is angled a
minimum of 1/4” per foot (21 mm/m) so that condensate will flow
back towards the furnace. Piping should be supported with pipe
hangers to prevent sagging.
FURNACE VENT CONNECTION SIZES
40 - 100 MBH
120 - 130 MBH
(35.2 - 39.6 kW)
Furnace Input
(17.5 - 29.3 kW)
9. Seal around the openings where the combustion air and / or vent
piping pass through the roof or sidewalls.
Intake Pipe Size
Vent Pipe Size
2” (5.1 cm)
2” (5.1 cm)
3” (7.6 cm)
2” (5.1 cm)
COMBUSTION AIR / VENTING
*. Vent pipe size must be increased to 3” diameter after connection to furnace
on this model.
The vent must be installed with the minimum required clearances,
and must comply with local codes and requirements.
22
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
VENT CLEARANCES
G
V
A
V
VENT TERMINAL
AIR SUPPLY
H
D
FIXED
CLOSED
X
E
B
V
B
B
I
AREA WHERE TERMINAL IS NOT PERMITTED
X
B
M
V
V
V
L
C
V
K
V
X
V
J
FIXED
CLOSED
V
F
B
B
OPERABLE
FIGURE 28: Home Layout
Canadian Installations1,3
US Installation2,3
Direct Vent Terminal Clearances
A. Clearance above grade, veranda, porch, deck, or
balcony
12 inches (30 cm)
12 inches (30 cm)
Two-pipe (direct vent) applications: 9 inches (23 cm)
12 inches (30 cm) for models ≤100,000 BTUH (30 kW), for models ≤50,000 BTUH (15 kW), 12 inches (30 cm)
36 inches (91 cm) for models >100,000 BTUH (30 kW) for models >50,000 BTUH (15 kW). ††
Single-pipe applications: 4 feet
B. Clearance to window or door that may be opened
C. Clearance to permanently closed window
12 inches (30 cm)
12 inches (30 cm)
D. Vertical clearance to ventilated soffit located
above the terminal within a horizontal distance
12 inches (30 cm) or in accordance with local
installation codes and the requirements of the gas
12 inches (30 cm) or in accordance with local
installation codes and the requirements of the gas sup-
plier
of 2 feet (61 cm) from the center line of the terminal supplier.
12 inches (30 cm) or in accordance with local
installation codes and the requirements of the gas
supplier
12 inches (30 cm) or in accordance with local
installation codes and the requirements of the gas
supplier
E. Clearance to unventilated soffit
12 inches (30 cm) or in accordance with local
installation codes and the requirements of the gas
supplier
12 inches (30 cm) or in accordance with local
installation codes and the requirements of the gas
supplier
F. Clearance to outside corner
G. Clearance to inside corner
3 feet (91 cm)
3 feet (91 cm)
Above a meter/regulator assembly within 3 feet (91 cm) Above a meter/regulator assembly within 3 feet (91
H. Clearance to each side of center line
extended above meter/regulator assembly
horizontally of the vertical center-line of the regulator
vent outlet to a maximum vertical distance of 15 feet
(4.5 cm) above the meter/regulator assembly.
cm) horizontally of the vertical center-line of the regula-
tor vent outlet to a maximum vertical distance of 15
feet (4.5 cm) above the meter/regulator assembly.
3 feet (91 cm) or in accordance with local installation
codes and the requirements of the gas supplier.
I. Clearance to service regulator vent outlet
3 feet (91 cm)
Two-pipe (direct vent) applications: 9 inches (23 cm)
J. Clearance to nonmechanical air supply inlet to
building or the combustion air inlet to any other
appliance
12 inches (30 cm) for models ≤100,000 BTUH (30 kW), for models ≤50,000 BTUH (15 kW), 12 inches (30 cm)
36 inches (91 cm) for models >100,000 BTUH (30 kW) for models >50,000 BTUH (15 kW).
Single-pipe applications: 4 feet
3 feet (91 cm) above if within 10 feet (3 cm)
K. Clearance to a mechanical supply inlet
6 feet (1.83 m)
horizontally
L. Clearance above paved sidewalk or paved
driveway located on public property
7 feet (2.13 m) or in accordance with local installation
codes and the requirements of the gas supplier.
7 feet (2.13 m)†
12 inches (30 cm) or in accordance with local installa-
M. Clearance under veranda, porch, deck, or balcony 12 inches (30 cm)‡
tion codes and the requirements of the gas supplier.
1. In accordance with the current CSA B149.1-00, Natural Gas and Propane Installation Code.
2. In accordance with the current ANSI Z223.1 / NFPA 54, National Gas Code.
3. In accordance with the current ANSI Z21.47 * CSA 2.3 American National Standard.
†
A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings.
†† 12 inches (30 cm) up from the bottom edge of the structure for Two-pipe (direct vent) applications per ANSI Z223.1 / NFPA 54, National Gas Code.
Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor and the distance between the top of the vent termina-
‡
tion and the underside of the veranda, porch, or deck is greater than 1 foot (30 cm) as specified in CSA B149.1-00.
A vent shall not terminate less than 1 foot (30 cm) above a grade level.
Any fresh air or make up inlet for dryer or furnace area is considered to be forced air inlet.
Avoid areas where condensate drippage may cause problems such as above planters, patios, or adjacent to windows where steam may cause fogging.
A terminus of a vent shall be fitted with a cap in accordance with the vent manufacturer’s installation instructions, or in accordance with the installation instructions for a
special venting system.
Responsibility for the provision of proper adequate venting and air supply for application shall rest with the installer.
Vent shall extend high enough above building, or a neighboring obstruction, so that wind from any direction will not create a positive pressure in the vicinity of the vent.
Consideration must be given for degradation of building materials by flue gases. Sidewall termination may require sealing or shielding of building surfaces with a corro-
sion resistant material to protect against combustion product corrosion. Consideration must be given to wind direction in order to prevent flue products and/or conden-
sate from being blown against the building surfaces. If a metal shield is used it must be a stainless steel material at a minimum dimension of 20 inches. It is
recommended that a retaining type collar be used that is attached to the building surface to prevent movement of the vent pipe.
Johnson Controls Unitary Products
23
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
VENT SYSTEM
This furnace is certified to be installed with one of two possible vent
configurations.
12” MIN.
1. Horizontal vent system. This vent system can be installed com-
pletely horizontal or combinations of horizontal, vertical, or offset
using elbows.
12” Minimum
below overhang
12” MIN.
12” Minimum
separation between
bottom of
combustion air
intake and
bottom of vent
2. Vertical vent system. This vent system can be installed completely
vertical or a combination of horizontal, vertical, or offset using
elbows.
VENT APPLICATIONS AND TERMINATION
When selecting the location for a combustion air / vent termination, the
following should be considered:
Maintain 12”
minimumclearance
above highest
1. Observe all clearances listed in vent clearances in these instruc-
tions.
anticipated snow
level or grade,
whichever is higher
2. Termination should be positioned where vent vapors will not dam-
age plants or shrubs or air conditioning equipment.
FIGURE 31: Termination Configuration - 2 Pipe Basement
3. Termination should be located where it will not be affected by wind
gusts, light snow, airborne leaves or allow recirculation of flue
gases.
VENTING MULTIPLE UNITS
Multiple units can be installed in a space or structure as either a single
4. Termination should be located where it will not be damaged or
exposed to flying stones, balls, etc.
pipe configuration or a two-pipe configuration.
The combustion air side of the single pipe configuration shown in Figure
29 is referred to in these instructions as ambient combustion air supply.
Follow the instructions for ambient combustion air installations, paying
particular attention to the section on air source from inside the building.
The vent for a single pipe system must be installed as specified in the
venting section of these instructions with the vent terminating as shown
in Figure 29. Each furnace must have a separate vent pipe. Under NO
circumstances can the two vent pipes be tied together.
5. Termination should be positioned where vent vapors are not objec-
tionable.
6. Horizontal portions of the vent system must slope upwards and be
supported to prevent sagging.
7. Direct vent systems must be installed so the vent and the combus-
tion air pipes terminate in the same atmospheric zone. Refer to
Figures 13 or 14.
Maintain 12” minimum clearance
above highest anticipated snow level.
Maximum 24” above roof.
The combustion air side of the two-pipe configuration shown in Figure
30 can be installed so the combustion air pipe terminates as described
in outdoor combustion air or ventilated combustion air sections in these
instructions. Follow the instructions for outdoor combustion air or venti-
lated combustion air and the instructions for installing the vent system
with the vent terminating as shown in Figures 32 or 33. The two-pipe
system must have a separate combustion air pipe and a separate vent
pipe for each furnace. Under NO circumstances can the two combus-
tion air or vent pipes be tied together. The combustion air and vent
pipes must terminate in the same atmospheric zone.
12” Min.
12” Min.
VENT
FIGURE 29: Termination Configuration - 1 Pipe
12” vertical separation
between combustion air
intake and vent.
COMBUSTION AIR
Maintain 12” minimum
clearance above
highest anticipated
snow level.
12” minimum
below overhang
2”
MIN.
12” minimum
separation between
bottom of
combustion air pipe
and bottom of vent.
FIGURE 32: Double Horizontal Combustion Air Intake and Vent
Termination
Maintain 12”
minimum clearance
above highest
anticipated snow
level or grade,
whichever is higher.
MIN.
6”
FIGURE 30: Termination Configuration - 2 Pipe
FIGURE 33: Double Vertical Combustion Air Intake and Vent
Termination
24
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
COMBUSTION AIR SUPPLY
Vent pipe cements
into socket just
above top panel
All installations must comply with Section 5.3, Air for Combustion and
Ventilation of the National Fuel Gas Code, ANSI Z223.1 or Sections
7.2, 7.3 or 7.4 of CAN/CGA B149.1 or .2 Installation Code - latest edi-
tions.
COMBUSTION AIR
This furnace is certified to be installed with one of three possible com-
bustion air intake configurations.
Or vent pipe may be
clamped into outlet
of drain coupling
1. OUTDOOR COMBUSTION AIR: This is a direct vent configuration
where the combustion air is supplied through a PVC or ABS pipe
that is connected to the PVC coupling attached to the furnace and
is terminated in the same atmospheric zone as the vent. This type
of installation is approved on all models. Refer to Figure 36.
2. AMBIENT COMBUSTION AIR: Combustion air is supplied from
the area surrounding the furnace through openings in the furnace
casing. The combustion air and the vent pipes are not terminated
in the same atmospheric zone. Refer to Figure 21 for vent termina-
tions. Refer to "Ambient Combustion Air Supply" for proper instal-
lation. Refer to Figure 36.
FIGURE 35: Combustion Airflow Path Through The Furnace Casing
3. VENTILATED COMBUSTION AIR: Combustion air is supplied
through a PVC or ABS pipe that is connected to the PVC coupling
attached to the burner box and is terminated in a ventilated attic or
crawl space. The combustion air and the vent pipes are not termi-
nated in the same atmospheric zone. Refer to Figure 37 for attic
and crawl space termination. Only the combustion air intake may
terminate in the attic. The vent must terminate outside.
This type of installation requires that the supply air to the appli-
ance(s) be of a sufficient amount to support all of the appliance(s)
in the area. Operation of a mechanical exhaust, such as an exhaust
fan, kitchen ventilation system, clothes dryer or fireplace may cre-
ate conditions requiring special attention to avoid unsatisfactory
operation of gas appliances. A venting problem or a lack of supply
air will result in a hazardous condition, which can cause the appli-
ance to soot and generate dangerous levels of CARBON MONOX-
IDE, which can lead to serious injury, property damage and / or
death.
Outdoor Combustion Air
Combustion Air Intake/Vent Connections
This installation requires combustion air to be brought in from outdoors.
This requires a properly sized pipe (Shown in Figure 30) that will bring
air in from the outdoors to the furnace combustion air intake collar on
the burner box. The second pipe (Shown in Figure 30) is the furnace
vent pipe.
An unconfined space is not less than 50 cu.ft (1.42 m3) per 1,000 Btu/
hr (0.2928 kW) input rating for all of the appliances installed in that
area.
Connects to
collar on top
of burner box
Rooms communicating directly with the space containing the appli-
ances are considered part of the unconfined space, if doors are fur-
nished with openings or louvers.
Vent pipe cements
into socket just
above top panel
A confined space is an area with less than 50 cu.ft (1.42 m3) per 1,000
Btu/hr (0.2928 kW) input rating for all of the appliances installed in that
area. The following must be considered to obtain proper air for combus-
tion and ventilation in confined spaces.
Or vent pipe may be
clamped into outlet
of drain coupling
Combustion Air Source From Outdoors
The blocking effects of louvers, grilles and screens must be given con-
sideration in calculating free area. If the free area of a specific louver or
grille is not known, refer to Table 11, to estimate free area.
Table 11: Estimated Free Area
Wood or Metal
Louvers or Grilles
Wood 20-25%*
Metal 60-70% *
FIGURE 34: Direct Vent Air Intake Connection and Vent Connection
1/4” (0.635 cm)
mesh or larger 100%
Screens+
The combustion air intake pipe should be located either through the
wall (horizontal or side vent) or through the roof (vertical vent). Care
should be taken to locate side vented systems where trees or shrubs
will not block or restrict supply air from entering the terminal.
* Do not use less than 1/4”(0.635 cm) mesh
+ Free area of louvers and grille varies widely; the installer should follow
louver or grille manufacturer’s instructions.
Also, the terminal assembly should be located as far as possible from a
swimming pool or a location where swimming pool chemicals might be
stored. Be sure the terminal assembly follows the outdoor clearances
listed in Section #1 “Outdoor Air Contaminants.”
Dampers, Louvers and Grilles (Canada Only)
1. The free area of a supply air opening shall be calculated by sub-
tracting the blockage area of all fixed louvers grilles or screens
from the gross area of the opening.
Ambient Combustion Air Supply
2. Apertures in a fixed louver, a grille, or screen shall have no dimen-
sion smaller than 0.25” (0.64 cm).
This type installation will draw the air required for combustion from
within the space surrounding the appliance and from areas or rooms
adjacent to the space surrounding the appliance. This may be from
within the space in a non-confined location or it may be brought into the
furnace area from outdoors through permanent openings or ducts. It is
not piped directly into the furnace. A single, properly sized pipe from the
furnace vent connector to the outdoors must be provided. It is recom-
mended that the supplied intake coupling & 18” of pipe be attached to
the furnace to prevent accidental blockage of the combustion air intake.
3. A manually operated damper or manually adjustable louvers are
not permitted for use.
4. A automatically operated damper or automatically adjustable lou-
vers shall be interlocked so that the main burner cannot operate
unless either the damper or the louver is in the fully open position.
Johnson Controls Unitary Products
25
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
Table 13: Free Area
Minimum Free Area Required for Each Opening
When a Category I furnace is removed or replaced, the original
venting system may no longer be correctly sized to properly vent
the attached appliances.
BTUH Input
Rating
Vertical Duct or
Opening to Outside
(4,000 BTUH)
Horizontal Duct
(2,000 BTUH)
Round Duct
(4,000 BTUH)
An improperly sized vent system can cause CARBON MONOXIDE
to spill into the living space causing personal injury, and or death.
20 in2 (129 cm2)
30 in2 (193 cm2)
40 in2 (258 cm2)
50 in2 (322 cm2)
60 in2 (387 cm2)
65 in2 (419 cm2)
10 in2 (64 cm2)
15 in2 (97 cm2)
20 in2 (129 cm2)
25 in2 (161 cm2)
30 in2 (193 cm2)
33 in2 (213 cm2)
40,000
60,000
4” (10 cm)
5” (13 cm)
5” (13 cm)
6” (15 cm)
7” (18 cm)
7” (18 cm)
Table 12: Unconfined Space Minimum Area in Square Inch
80,000
Minimum Free Area in Square Feet
BTUH Input Rating
100,000
120,000
130,000
Required for Each Opening
40 (258 cm2)
40,000
60 (387 cm2)
60,000
EXAMPLE: Determining Free Area.
Appliance 1 Appliance
80 (516 cm2)
80,000
2 Total Input
100,000 + 30,000 = (130,000 ÷ 4,000) = 32.5 Sq. In. Vertical
Appliance 1 Appliance 2 Total Input
100,000 + 30,000 = (130,000 ÷ 2,000) = 65 Sq. In. Horizontal
100 (645 cm2)
100,000
120 (742 cm2)
120,000
130 (838 cm2)
130,000
Gas
Vent
Gas
Vent
Gas
Vent
Gable
Vent
Gable
Vent
Ventilated
Attic
Ventilated
Attic
Optional
Inlet (a)
Top Above
Insulation
Top Above
Insulation
Outlet
Air (a)
Soffit
Vent
Soffit
Vent
Outlet
Air (b)
Outlet
Air (a)
Gas
Water
Heater
Gas
Water
Heater
Gas
Water
Heater
Inlet
Air (b)
Inlet
Air (b)
Inlet
Air (a)
Inlet
Air (a)
Ventilated
Crawl Space
FIGURE 36: Outside and Ambient Combustion Air
7. An air supply inlet opening from the outdoors shall be located not
less than 12” (30.5 cm) above the outside grade level.
Air Supply Openings and Ducts
1. An opening may be used in lieu of a duct to provide to provide the
outside air supply to an appliance unless otherwise permitted by
the authority having jurisdiction. The opening shall be located
within 12” (30.5 cm) horizontally from, the burner level of the appli-
ance. Refer to “AIR SOURCE FROM OUTDOORS AND VENT
AND SUPPLY AIR SAFETY CHECK” in these instructions for
additional information and safety check procedure.
Combustion Air Source from Outdoors
1. Two permanent openings, one within 12 in (30.5 mm) of the top
and one within 12 in (30.5 mm) of bottom of the confined space,
Two permanent openings, shall communicate directly or by means
of ducts with the outdoors, crawl spaces or attic spaces.
2. One permanent openings, commencing within 12 in (30.5 mm) of
the top of the enclosure shall be permitted where the equipment
has clearances of at least 1 in (2.54 cm) from the sides and back
and 6 in (15.24 cm) from the front of the appliance. The opening
shall communicate directly with the outdoors and shall have a min-
imum free area of:
2. The duct shall be either metal, or a material meeting the class 1
requirements of CAN4-S110 Standard for Air Ducts.
3. The duct shall be least the same cross-sectional area as the free
area of the air supply inlet opening to which it connects.
4. The duct shall terminate within 12 in (30.5 cm) above, and within
24 in (61 cm) horizontally from, the burner level of the appliance
having the largest input.
a. 1 square in per 3000 Btu per hour (6.45 cm3 per 0.879 kW) of
the total input rating of all equipment located in the enclosure.
5. A square or rectangular shaped duct shall only be used when the
b. Not less than the sum of all vent connectors in the confined
space.
required free area of the supply opening is 9 in2 (58.06 cm2) or
larger. When a square or rectangular duct is used, its small dimen-
sion shall not be less than 3 in (7.6 cm).
3. The duct shall be least the same cross-sectional area as the free
area of the air supply inlet opening to which it connects.
6. An air inlet supply from outdoors shall be equipped with a means
to prevent the direct entry of rain and wind. Such means shall not
reduce the required free area of the air supply opening.
4. The blocking effects of louvers, grilles and screens must be given
consideration in calculating free area. If the free area of a specific
louver or grille is not known. Refer to Table 11, "Estimated Free
Area".
26
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
Ventilated Combustion Air
Ventilated Combustion Air Termination
The ventilated attic space or a crawl space from which the combustion
air is taken must comply with the requirements specified in “AIR
SOURCE FROM OUTDOORS” in this instruction or in Section 5.3, Air
for Combustion and Ventilation of the National Fuel Gas Code, ANSI
Z223.1 (latest edition). This type installation requires two properly sized
pipes. One brings combustion air from a properly ventilated attic space
or crawl space and a second pipe that extends from the furnace vent
connection (top right of unit) to the exterior of the building. Refer to
Table 7, "Maximum Equivalent Pipe Length" for intake pipe sizing,
allowable length and elbow usage. Follow all notes, procedures and
required materials in the "COMBUSTION AIR/VENT PIPE SIZING" sec-
tion in these instructions when installing the combustion air pipe from
the unit and into a ventilated attic space or crawl space. DO NOT termi-
nate vent pipe in an Attic or Crawl Space.
Refer to Figure 37, "Attic and Crawl Space Combustion Air Termination"
for required attic termination for the combustion air intake pipe. For attic
termination, use two 90 elbows with the open end in a downward posi-
tion. Be sure to maintain 12” (30 cm) clearance above any insulation,
flooring or other material.
A crawl space combustion air installation consists of a straight pipe from
the PVC coupling on the burner box that extends into the crawl space
and terminates with a 1/4” (6.35 mm) mesh screen and no elbows.
CARBON MONOXIDE POISONING HAZARD
Failure to follow the steps outlined below for each appliance connected to the venting system being placed into operation could result in carbon-
monxide poisoning or death.
The following steps shall be followed for each appliance connected to the venting system being placed into operation, while all other appliances
connected to the venting system are not in operation:
1. Inspect the venting system for proper size and horizontal pitch. Determine that there is no blockage, restriction, leakage, corrosion or other
deficiencies, which could cause an unsafe condition
2. Close all building doors and windows and all doors.
3. Turn on clothes dryers and TURN ON any exhaust fans, such as range hoods and bathroom exhausts, so they shall operate at maximum
speed. Open the fireplace dampers. Do not operate a summer exhaust fan.
4. Follow the lighting instructions. Place the appliance being inspected in operation. Adjust thermostat so the appliance shall operate contin-
uously.
5. Test each appliance (such as a water heater) equipped with a draft hood for spillage (down-draft or no draft) at the draft hood relief opening
after 5 minutes of main burner operation. Appliances that do not have draft hoods need to be checked at the vent pipe as close to the
appliance as possible. Use a combustion analyzer to check the CO2 and CO levels of each appliance. Use a draft gauge to check for a
downdraft or inadequate draft condition.
6. After it has been determined that each appliance properly vents when tested as outlined above, return doors, windows, exhaust fans, fire-
place dampers and any other gas burning appliance to their normal condition.
7. If improper venting is observed during any of the above tests, a problem exists with either the venting system or the appliance does not
have enough combustion air (Supply Air from outside) to complete combustion. This condition must be corrected before the appliance can
function safely.
NOTE: An unsafe condition exists when the CO reading exceeds 40 ppm and the draft reading is not in excess of - 0.1 in. W.C. (-25 kPa) with
all of the appliance(s) operating at the same time.
8. Any corrections to the venting system and / or to the supply (outside) air system must be in accordance with the National Fuel Gas Code
Z223.1 or CAN/CGA B149.1 Natural Gas and Propane Installation Code (latest editions). If the vent system must be resized, follow the
appropriate tables in Appendix G of the above codes or for this appliance.
Specially Engineered Installations
The above requirements shall be permitted to be waived where special
engineering, approved by the authority having jurisdiction, provides an
12” minimum
between bottom
adequate supply of air for combustion and ventilation.
of air intake and
any material below.
12” Min.
Be sure to instruct the owner not to block this intake pipe.
VENT BLOWER ROTATION
For ease of venting, the vent blower may be rotated 90° in either direc-
tion. For upflow installations the vent may exit through the top or either
side of the cabinet. For downflow installations, the vent blower must be
rotated so that the vent exits through either side of the cabinet. See Fig-
ures 23-26 for details.
FIGURE 37: Attic and Crawl Space Combustion Air Termination
Johnson Controls Unitary Products
27
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
IGNITION SYSTEM SEQUENCE
SECTION IX: START-UP AND
ADJUSTMENTS
1. Turn the gas supply ON at external valve and main gas valve.
2. Set the thermostat above room temperature to call for heat.
3. System start-up will occur as follows:
The initial start-up of the furnace requires the following additional
procedures:
a. The induced draft blower motor will start and come up to
speed. Shortly after inducer start-up, the hot surface igniter
will glow for about 17 seconds.
All electrical connections made in the field and in the factory should
be checked for proper tightness.
b. After this warm up, the ignition module will energize (open)
the main gas valve.
c. After flame is established, the supply air blower will start in
about 30 seconds.
When the gas supply is initially connected to the furnace, the gas piping
may be full of air. In order to purge this air, it is recommended that the
ground union be loosened until the odor of gas is detected. When gas is
detected, immediately retighten the union and check for leaks. Allow
five minutes for any gas to dissipate before continuing with the start-up
procedure. Be sure proper ventilation is available to dilute and carry
away any vented gas.
CALCULATING THE FURNACE INPUT
(NATURAL GAS)
Burner orifices are sized to provide proper input rate using natural gas
with a heating value of 1030 BTU/Ft3 (38.4 MJ/m3). If the heating value
of your gas is significantly different, it may be necessary to replace the
orifices.
GAS PIPING LEAK CHECK
NOTE: DO NOT set manifold pressure less than 3.2 in wc or more than
3.8 in wc for natural gas at sea level. If manifold pressure is outside this
range, change main burner orifices.
NOTE: If orifice hole appears damaged or it is suspected to have been
redrilled, check orifice hole with a numbered drill bit of correct size.
Never redrill an orifice. A burr-free and squarely aligned orifice hole is
essential for proper flame characteristics.
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warnings exactly could result in serious
injury, death or property damage.
Never test for gas leaks with an open flame. Use a commercially
available soap solution made specifically for the detection of leaks
to check all connections. A fire or explosion may result causing
property damage, personal injury or loss of life.
DO NOT bottom out gas valve regulator adjusting screw. This can
result in unregulated manifold pressure and result in excess over-
fire and heat exchanger failures.
Burner ignition may not be satisfactory on first startup due to resid-
ual air in the gas line or until gas manifold pressure is adjusted. The
ignition control will make three attempts to light before locking out.
Verify natural gas input rate by clocking meter.
1. Turn off all other gas appliances and pilots.
2. Run furnace for a minimum of 3 minutes in heating operation.
It is recommended that when the gas supply is first connected to the
furnace, the ground union be loosened until the odor of gas is detected.
When gas is detected, immediately tighten the union and check for gas
leaks. Allow five minutes for any gas to dissipate before continuing with
the startup procedure. Be sure that proper ventilation is available to
dilute and carry away any vented gas.
3. Measure time (in sec) for gas meter to complete 1 revolution and
note reading. The 2 cubic feet dial provides a more accurate mea-
surement of gas flow.
4. Refer to Table 9 for cubic feet of gas per hour.
5. Multiply cubic feet per hour by heating valve (BTU/cu ft) to obtain
input.
With furnace in operation, check all of the pipe joints, gas valve connec-
tions and manual valve connections for leakage using an approved gas
detector, a non-corrosive leak detection fluid or other leak detection
methods. Take appropriate action to stop any leak. If a leak persists,
replace the faulty component.
If clocked rate does not match the input rate from the unit nameplate.
follow steps in next section to adjust the manifold pressure. Repeat
steps 2 - 5 until correct input is achieved.
The furnace and its equipment shutoff valve must be disconnected from
the gas supply during any pressure testing of that system at test pres-
sures in excess of 1/2 PSI (3.45 kPa).
Be sure to relight any gas appliances that were turned off at the
start of this input check.
The furnace must be isolated from the gas supply piping system by
closing the equipment shutoff valve during any pressure testing of the
gas supply system.
28
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
Table 14: Gas Rate (CU FT/HR) at Full Input
Size of Test Dial
Size of Test Dial
Seconds For
1 Revolution
Seconds For
1 Revolution
1 Cu Ft
360
327
300
277
257
240
225
212
200
189
180
171
164
157
150
144
138
133
129
124
120
116
113
109
106
103
100
97
2 Cu Ft
720
655
600
555
514
480
450
424
400
379
360
343
327
313
300
288
277
267
257
248
240
232
225
218
212
206
200
195
189
185
180
176
172
167
164
160
157
153
150
147
144
141
138
136
133
5 Cu Ft
1800
1636
1500
1385
1286
1200
1125
1059
1000
947
900
857
818
783
750
720
692
667
643
621
600
581
563
545
529
514
500
486
474
462
450
439
429
419
409
400
391
383
375
367
360
355
346
340
333
1 Cu Ft
65
64
63
62
61
60
58
56
54
53
51
50
48
47
46
45
44
43
42
41
40
39
38
38
37
36
35
35
34
33
33
32
31
30
29
28
27
26
25
24
23
22
21
20
2 Cu Ft
131
129
126
124
122
120
116
112
109
106
103
100
97
5 Cu Ft
327
321
316
310
305
300
290
281
273
265
257
250
243
237
231
225
220
214
209
205
200
196
192
188
184
180
178
173
170
167
164
161
155
150
145
141
135
130
125
120
115
110
105
100
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
62
64
66
68
70
72
74
76
95
78
92
80
90
82
88
84
86
86
84
88
82
90
80
92
78
94
76
96
75
98
74
100
102
104
106
108
110
112
116
120
124
128
133
138
144
150
157
164
171
180
72
71
69
95
68
92
67
90
65
88
64
86
62
84
60
82
58
80
56
78
54
76
52
75
50
73
48
72
46
71
44
69
42
68
40
67
Johnson Controls Unitary Products
29
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
NOTE: The regulated outlet pressure has been calibrated at the factory.
Additional pressure adjustment should not be necessary. If adjustment
is necessary, set to the following specifications. After adjustment, check
for gas leakage.
ADJUSTMENT OF MANIFOLD GAS PRESSURE &
INPUT RATE
Inlet and manifold gas pressure may be measured by connecting the
“U” tube manometer to the gas valve with a piece of tubing. Follow the
appropriate section in the instructions below. Refer to Figure 38, "Gas
Valve" for a drawing of the locations of the pressure ports on the gas
valve.
1. Refer to Figure 38, "Gas Valve" for location of pressure regulator
adjustment cap and adjustment screws on main gas valve.
2. Turn gas and electrical supplies on and follow the operating
instructions to place the unit back in operation.
Turn gas off at the ball valve or gas cock on gas supply line
before the gas valve. Find the pressure ports on the gas
valve marked Out P and In P.
3. Adjust manifold pressure by adjusting gas valve regulator screw
for the appropriate gas per the following:
Table 16: Nominal Manifold Pressure
1. The manifold pressure must be taken at the port marked OUT P.
2. The gas line pressure must be taken at the port marked IN P.
NOMINAL MANIFOLD PRESSURE
Natural Gas
3.5" w.c. (0.87 kPa)
3. Using a 3/32” (2.4 mm) Allen wrench, loosen the set screw by turn-
ing it 1 turn counter clockwise. DO NOT REMOVE THE SET
SCREW FROM THE PRESSURE PORT.
Propane (LP) Gas
10.0" w.c. (2.488 kPa)
Read the inlet gas pressure
OUTLET
PRESSURE
PORT
VENT PORT
Connect the positive side of the manometer to the IN P Tap on the gas
valve. Do not connect any tubing to the negative side of the manometer,
as it will reference atmospheric pressure. Refer to Figure 39, "Reading
Gas Pressure" for connection details.
INLET
OUTLET
1. Turn gas and electrical supplies on and follow the operating
instructions to place the unit back in operation.
WRENCH
BOSS
INLET
PRESSURE
PORT
MAIN REGULATOR
ADJUSTMENT
Table 15: Inlet Gas Pressure Range
ON/OFF SWITCH
(Shown in ON position)
INLET GAS PRESSURE RANGE
Natural Gas
Propane (LP)
FIGURE 38: Gas Valve
Minimum
Maximum
4.5” W.C. (1.12 kPa)
10.5” W.C. (2.61 kPa)
8.0” W.C. (1.99 kPa)
13.0” (3.24 kPa) W.C.
If gas valve regulator is turned in (clockwise), manifold pressure is
increased. If screw is turned out (counterclockwise), manifold pres-
sure will decrease.
The inlet gas pressure operating range table specifies what the
minimum and maximum gas line pressures must be for the furnace
to operate safely. The gas line pressure MUST BE a minimum of:
4. After the manifold pressure has been adjusted, re-calculate the
furnace input to make sure you have not exceeded the specified
input on the rating plate. Refer to “CALCULATING THE FURNACE
INPUT (NATURAL GAS)”.
•
•
7” W.C. (1.74 kPA) for Natural Gas
11” W.C. (2.74 kPA) for Propane (LP) Gas
in order to obtain the BTU input specified on the rating plate and/or
the nominal manifold pressure specified in these instructions and
on the rating plate.
5. Once the correct BTU (kW) input has been established, turn the
gas valve to OFF and turn the electrical supply switch to OFF; then
remove the flexible tubing from the gas valve pressure tap and
tighten the pressure tap plug using the 3/32” (2.4 mm) Allen
wrench.
2. Once the correct gas inlet pressure has been established, see
Table 15, "Inlet Gas Pressure Range", turn the gas valve to OFF
and turn the electrical supply switch to OFF; then remove the flexi-
ble tubing from the gas valve pressure tap and tighten the pres-
sure tap plug using the 3/32” (2.4 mm) allen wrench.
6. Turn the electrical and gas supplies back on, and with the burners
in operation, check for gas leakage around the gas valve pressure
port for leakage using an approved non-corrosive gas leak detec-
tion fluid, or other non-flammable leak detection methods.
3. Turn the electrical and gas supplies back on, and with the burners
in operation, check for gas leakage around the gas valve pressure
port for leakage using an approved non-corrosive gas leak detec-
tion fluid, or other non-flammable leak detection methods.
MANIFOLD PRESSURE “U” TUBE CONNECTION
OUTLET
PRESSURE TAP
Read the manifold gas pressure
GAS VALVE
1/4” TUBING
Connect the positive side of the manometer to the adapter previously
installed in the OUT P Tap on the gas valve. Do not connect any tubing
to the negative side of the manometer, as it will reference atmospheric
pressure. Refer to Figure 39, "Reading Gas Pressure" for connection
details.
MAINIFOLD
PIPE
FLAME
SENSOR
3.5 IN
WATER
The cap for the pressure regulator must be removed entirely to gain
access to the adjustment screw. Loosening or tightening the cap
does not adjust the flow of gas.
COLUMN
GAS
PRESSURE
SHOWN
GAS
BURNERS
U-TUBE
MANOMETER
FIGURE 39: Reading Gas Pressure
30
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
All direct-drive blowers have multi-speed motors. The blower motor
speed taps are located on the furnace control board in the blower com-
partment. Refer to Figure 40, "Furnace Control Board", and the unit-wir-
ing label to change the blower speed. To use the same speed tap for
heating and cooling, the heat terminal and cool terminal must be con-
nected using a jumper wire and connected to the desired motor lead.
Place all unused motor leads on Park terminals. Two park terminals are
provided.
ADJUSTMENT OF TEMPERATURE RISE
The temperature rise, or temperature difference between the return
air and the supply (heated) air from the furnace, must be within the
range shown on the furnace rating plate and within the application
limitations shown in Table 6, "Ratings & Physical / Electrical Data".
The supply air temperature cannot exceed the “Maximum Supply
Air Temperature” specified in these instructions and on the fur-
nace rating plate. Under NO circumstances can the furnace be
allowed to operate above the Maximum Supply Air Temperature.
Operating the furnace above the Maximum Supply Air Temperature
will cause premature heat exchanger failure, high levels of Carbon
Monoxide, a fire hazard, personal injury, property damage, and/or
death.
Do not energize more than one motor speed at a time or damage to
the motor will result.
ADJUSTMENT OF FAN CONTROL SETTINGS
This furnace is equipped with a time-on/time-off heating fan control. The
fan on delay is fixed at 30 seconds. The fan off delay has 4 settings (60,
90, 120 and 180 seconds). The fan off delay is factory set to 120 sec-
onds. The fan-off setting must be long enough to adequately cool the
furnace, but not so long that cold air is blown into the heated space. The
fan-off timing may be adjusted by positioning the jumper on two of the
four pins as shown in Figure 40, "Furnace Control Board".
After about 5 minutes of operation, determine the furnace temperature
rise. Take readings of both the return air and the heated air in the ducts,
about six feet (1.83 m) from the furnace where they will not be affected
by radiant heat. Increase the blower speed to decrease the temperature
rise; decrease the blower speed to increase the rise.
TWIN
PARK PARK
Blower Off Delay Timer
Adjustment Jumper
(in seconds)
HI COOL
HEAT
EAC-H
L1
XFMR
HUM
FIGURE 40: Furnace Control Board
ROLLOUT SWITCH CONTROLS
SECTION X: SAFETY CONTROLS
These controls are mounted on the burner assembly. If the temperature
in the area surrounding burner exceeds its set point, the gas valve is
de-energized. The operation of this control indicates a malfunction in
the combustion air blower, heat exchanger or a blocked vent pipe con-
nection. Corrective action is required. These are manual reset controls
that must be reset before operation can continue.
CONTROL CIRCUIT FUSE
A 3-amp fuse is provided on the control circuit board to protect the 24-
volt transformer from overload caused by control circuit wiring errors.
This is an ATO 3, automotive type fuse and is located on the control
board.
BLOWER DOOR SAFETY SWITCH
PRESSURE SWITCHES
This furnace is supplied with two pressure switches, which monitor the
flow through the combustion air/vent piping and condensate drain sys-
tem. These switches de-energize the gas valve if any of the following
conditions are present. Refer to "CONDENSATE PIPING AND FUR-
NACE VENTING CONFIGURATION" for tubing connections.
Main power to the unit must still be interrupted at the main power
disconnect switch before any service or repair work is to be done to
the unit. Do not rely upon the interlock switch as a main power dis-
connect.
1. Blockage of vent piping or terminal.
2. Failure of combustion air blower motor.
3. Blockage of combustion air piping or terminals.
4. Blockage of condensate drain piping.
Blower and burner must never be operated without the blower
panel in place.
This unit is equipped with an electrical interlock switch mounted in the
burner compartment. This switch interrupts all power at the unit when
the panel covering the blower compartment is removed.
Electrical supply to this unit is dependent upon the panel that covers the
blower compartment being in place and properly positioned.
Johnson Controls Unitary Products
31
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
During burner operation, a momentary loss of power for 50 milliseconds
or longer will de-energize the gas valve. When the power is restored,
the gas valve will remain de-energized and the ignition sequence will
immediately restart.
LIMIT CONTROLS
There is a high temperature limit control located on the furnace vesti-
bule panel near the gas valve. This is an automatic reset control that
provides over temperature protection due to reduced airflow. This may
be caused by:
Hot Surface Ignition System
1. A dirty filter.
2. If the indoor fan motor should fail.
3. Too many supply or return registers closed or blocked off.
HOT SURFACE IGNITION SYSTEM
The control module will lockout if the limit trips 5 consecutive times. If
this occurs, control will reset & try ignition again after 1 hour.
Do not attempt to light this furnace by hand (with a
match or any other means). There may be a potential
shock hazard from the components of the hot surface
ignition system. The furnace can only be lit automatically
by its hot surface ignition system.
SEQUENCE OF OPERATION
The following describes the sequence of operation of the furnace. Refer
to Owners Manual for component location.
Continuous Blower
TROUBLESHOOTING
The following visual checks should be made before troubleshooting:
Cooling/heating thermostats have a fan switch that has an ON and
AUTO position. In the ON position the thermostat circuit is completed
between terminals R and G. The motor will operate continuously on the
speed tap wire that is connected to the “HI COOL” cooling terminal on
the control board. To obtain a constant air circulation at lower flow rate,
change the high-speed wire to either the medium speed wire or the low
speed wire.
1. Check to see that the power to the furnace and the ignition control
module is ON.
2. The manual shut-off valves in the gas line to the furnace must be
open.
3. Make sure all wiring connections are secure.
4. Review the sequence of operation. Start the system by setting the
thermostat above the room temperature. Observe the system’s
response. Then use the troubleshooting section in this manual to
check the system’s operation.
Intermittent Blower - Cooling
Cooling/heating thermostats have a fan switch that has an ON and
AUTO position. In the AUTO position the thermostat circuit is completed
between terminals R and G when there is a call for cooling. The motor
will operate on the speed tap wire that is connected to the “HI COOL”
cooling terminal on the control board. The fan off setting is fixed at 60
seconds to improve cooling efficiency.
Never bypass any safety control to allow furnace opera-
tion. To do so will allow furnace to operate under poten-
tially hazardous conditions.
Heating Cycle
When the thermostat switch is set on HEAT and the fan is set on AUTO,
and there is a call for heat, a circuit is completed between terminals R
and W of the thermostat. When the proper amount of combustion air is
being provided, the pressure switch will close, the ignition control pro-
vides a 17-second ignitor warm-up period, the gas valve then opens,
the gas starts to flow, ignition occurs and the flame sensor begins its
sensing function. The blower motor will energize 30 seconds after the
gas valve opens, if a flame is detected. Normal furnace operation will
continue until the thermostat circuit between R and W is opened, which
causes the ignition system and gas valve to de-energize and the burner
flames to be extinguished. The vent motor will operate for 15 seconds
and the blower motor will operate for the amount of time set by the fan-
off delay jumper located on the control board. See Figure 36. The heat-
ing cycle is now complete, and ready for the start of the next heating
cycle.
Do not try to repair controls. Replace defective controls
with UPG Source 1 Parts.
Never adjust pressure switch to allow furnace operation.
FURNACE CONTROL DIAGNOSTICS
The furnace has built-in, self-diagnostic capability. If a system problem
occurs, a blinking LED can flash red, green or amber to indicate various
conditions.
The control continuously monitors its own operation and the operation
of the system. If a failure occurs, the LED will indicate the failure code. If
the failure is internal to the control, the light will stay on continuously. In
this case, the entire control should be replaced, as the control is not
field repairable.
Flash sequence codes 1 through 11 are as follows: LED will turn “on”
for 1/4 second and “off” for 1/4 second. This pattern will be repeated the
number of times equal to the code. For example, six “on” flashes equals
a number 6 fault code. All flash code sequences are broken by a 2 sec-
ond “off” period.
If the flame is not detected within 7 seconds of the gas valve opening,
the gas valve is shut off and a retry operation begins. Also, if the flame
is lost for 2 seconds during the 10-second stabilization period, the gas
valve is shut off and a retry operation begins. During a retry operation,
the vent motor starts a 15 second inter-purge and the ignitor warm-up
time is extended to 27 seconds. If the flame is established for more than
10 seconds after ignition during a retry, the control will clear the ignition
attempt (retry) counter. If three retries occur during a call for heat, the
furnace will shut down for one hour. If at the end of the one hour shut
down there is a call for heat, the furnace will initiate a normal start cycle.
If the problem has not been corrected the furnace will again lockout
after three retries.
SLOW GREEN FLASH: Normal operation.
SLOW AMBER FLASH: Normal operation with call for heat.
RAPID RED FLASH: Twinning error, incorrect 24V phasing. Check
twinning wiring.
RAPID AMBER FLASH: Flame sense current is below 1.5 microamps.
Check and clean flame sensor. Check for proper gas flow. Verify that
current is greater than 1.5 microamps at flame current test pad.
4 AMBER FLASHES: The control is receiving a “Y” signal from the
thermostat without a “G” signal, indicating improper thermostat wiring.
A momentary loss of gas supply, flame blowout, or a faulty flame probe
circuit will result in a disruption in the flame and be sensed within 1.0
seconds. The gas valve will de-energize and the control will begin a
recycle operation. A normal ignition sequence will begin after a 15 sec-
ond inter-purge. If during the five recycles the gas supply does not
return, or the fault condition is not corrected the ignition control will lock-
out for 60 minutes.
1 RED FLASH: This indicates that flame was sensed when there was
not a call for heat. The control will turn on both the inducer motor and
supply air blower. A gas valve that leaks or is slow closing would typi-
cally cause this fault.
2 RED FLASHES: This indicates that the normally open pressure
switch contacts are stuck in the closed position. The control confirms
these contacts are open at the beginning of each heat cycle. This would
indicate a faulty pressure switch or miswiring.
32
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
3 RED FLASHES: This indicates the normally open pressure switch
contact did not close after the inducer was energized. This could be
caused by a number of problems: faulty inducer, blocked vent pipe, bro-
ken pressure switch hose or faulty pressure switch.
STEADY ON RED: Control failure. Replace control board.
60-MINUTE AUTOMATIC RESET FROM LOCKOUT: This control
includes a “watchdog” type circuit that will reset from a lockout condition
after 60 minutes. Operational faults 6,7,8 will be reset. This provides
protection to an unoccupied structure if a temporary condition exists
causing a furnace malfunction. An example would be a low incoming
gas supply pressure preventing unit operation. When the gas pressure
is restored, at some point the “watchdog” would restart the unit and pro-
vide heat for the house.
4 RED FLASHES: This indicates that the main limit switch has opened
its normally closed contacts. The control will operate the supply air
blower and inducer. This condition may be caused by: dirty filter,
improperly sized duct system, incorrect blower speed setting, incorrect
firing rate or faulty blower motor. Also, this fault code could be caused
by a blown fuse located on the control board.
NOTE: If a flame is detected the control flashes the LED for 1/8 of a
second and then enters a flame stabilization period.
5 RED FLASHES: This fault is indicated if the normally closed contacts
in the rollout switch opens. The rollout control is manually reset. If it has
opened, check for proper combustion air, proper inducer operation, and
primary heat exchanger failure or burner problem. Be sure to reset the
switch and cycle power (24 VAC) to the control after correcting the fail-
ure condition. Also, this fault code could be caused by a blown fuse
located on the control board.
IGNITION CONTROL FLAME SENSE LEVELS
Normal flame sense current is approximately
3.7 microamps DC (µa)
Low flame signal warning starts at 1.5 microamps.
Low flame signal control lockout point is
0.1 microamps DC (µa)
6 RED FLASHES: This indicates that after the unit was operating, the
pressure switch opened 4 times during the call for heat. If the main
blower is in a “Delay on” mode, it will complete it, and any subsequent
delay off period. The furnace will lock out for one hour and then restart.
DIAGNOSTIC FAULT CODE STORAGE AND
RETRIEVAL
The control in this furnace is equipped with memory that will store up to
five error codes to allow a service technician to diagnose problems
more easily. This memory will be retained even if power to the furnace
is lost. This feature should only be used by a qualified service tech-
nician.
7 RED FLASHES: This fault code indicates that the flame could not be
established. This no-light condition occurred 3 times (2 retries) during
the call for heat before locking out. Low gas pressure, faulty gas valve,
dirty or faulty flame sensor, faulty hot surface ignitor or burner problem
may cause this. The furnace will lock out for one hour and then restart.
If more than five error codes have occurred since the last reset, only the
five most recent will be retained. The furnace control board has a but-
ton, labeled "LAST ERROR" that is used to retrieve error codes. This
function will only work if there are no active thermostat signals. So any
call for heating, cooling or continuous fan must be terminated before
attempting to retrieve error codes.
8 RED FLASHES: This fault is indicated if the flame is lost 5 times (4
recycles) during the heating cycle. This could be caused by low gas
pressure, dirty or faulty flame sensor or faulty gas valve. The furnace
will lock out for one hour and then restart.
9 RED FLASHES: Indicates reversed line voltage polarity or grounding
problem. Both heating and cooling operations will be affected. Check
polarity at furnace and branch. Check furnace grounding. Check that
flame probe is not shorted to chassis.
To retrieve the error codes, push the LAST ERROR button. The LED on
the control will then flash the error codes that are in memory, starting
with the most recent. There will be a two-second pause between each
flash code. After the error codes have all been displayed, the LED will
resume the normal slow green flash after a five second pause. To
repeat the series of error codes, push the button again.
10 RED FLASHES: Flame sensed with no call for heat. Check gas
valve and gas valve wiring.
11 RED FLASHES: This indicates that a primary or auxiliary limit switch
has opened its normally-closed contacts and has remained open for
more than five minutes. This condition is usually caused by a failed
blower motor or blower wheel. Cycle power (24 VAC) to the control to
reset the hard lockout condition after correcting the failure condition.
If there are no error codes in memory, the LED will flash two green
flashes. To clear the memory, push the LAST ERROR button and hold it
for more than five seconds. The LED will flash three green flashes when
the memory has been cleared, then will resume the normal slow green
flash after a five-second pause.
12 RED FLASHES: This code indicates an open igniter circuit, which
could be a disconnected or loose wire or a cracked or broken igniter.
Thermostat Calling for Heat
22
52
Thermostat Satisfied
(Seconds)
0 2
17
0
Fan on Delay
30 Seconds
ON
ON
ON
THERMOSTAT
INDUCER
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
15
OFF
OFF
Sec.
Post
Purge
IGNITOR
OFF
ON
MAIN VALVE
OFF
ON
HUMIDIFIER
OFF
OFF
OFF
OFF
ELECTRONIC
AIR CLEANER
ON
ON
OFF
OFF
CIRCULATING
BLOWER
60, 90, 120, 180 SEC.
Selectable Fan Off Delay
FIGURE 41: Furnace Control Event Schedule
Johnson Controls Unitary Products
33
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
SECTION XI: REPLACEMENT PARTS LIST
DESCRIPTION
FABRICATED PARTS Continued
MANIFOLD, GAS
DESCRIPTION
MOTOR
MOTOR, DIRECT DRIVE BLOWER
BLOWER, COMBUSTION
ELECTRICAL
PAN, BOTTOM
PANEL, TOP
PANEL, DOOR (2 Req’d)
PANEL, BLOCKOFF
MISCELLANEOUS
CAPACITOR, RUN
SWITCH, LIMIT
CONTROL, FURNACE
IGNITER
ORIFICE, BURNER (Natural #45)
SIGHT GLASS, OVAL (2 Req’d)
GASKET, FOAM (Door) (1.5 ft req’d)
PAN, CONDENSATE
BRACKET, DOOR
SENSOR, FLAME
SWITCHES, PRESSURE
SWITCH, DOOR
TRANSFORMER
HARNESS, WIRING
FERRULE (3 Req’d)
VALVE, GAS
CONTROL, TEMPERATURE
AIR MOVING
GROMMET (3 Req’d)
MOTOR MOUNT
HOUSING, BLOWER
WHEEL, BLOWER
TUBING, SILICON
HOSE, RAIN GUTTER
HOSE, CONDENSATE
PLUG, SEAL, 7/8”
FABRICATED PARTS
RESTRICTOR, COMBUSTION BLOWER
BURNER, MAIN GAS
BRACKET, IGNITER
SHELF, BLOWER
PLUG, SEAL, 2-3/8”
PLUG, VENT PIPE
BAG, PARTS
RAIL, BLOWER (2 Req’d)
BRACKET, BLOWER TRACK (2 Req’d)
HEAT EXCHANGER ASS’Y
KNOB, QUARTER TURN (4 Req’d)
DIAGRAM, WIRING
REPLACEMENT PART CONTACT INFORMATION
This is a generic parts list. To request a complete parts list, refer to the contact information below:
1. Search for a part or browse the catalog.
2. Find a dealer or distributor.
3. Customer Service contact information.
a. Click on the “Brand Links” button
b. Click on the “Customer Service” button
• You can contact us by mail. Just send a written request to:
Johnson Controls Unitary Products
Consumer Relations
5005 York Drive
Norman, OK 73069
34
Johnson Controls Unitary Products
Download from Www.Somanuals.com. All Manuals Search And Download.
364861-UIM-B-0708
SECTION XII: WIRING DIAGRAM
FIGURE 42: Wiring Diagram
Johnson Controls Unitary Products
35
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Subject to change without notice. Printed in U.S.A.
364861-UIM-B-0708
Copyright © 2008 by Johnson Controls, Inc. All rights reserved.
Supersedes: 364861-UIM-A-0608
Johnson Controls Unitary Products
5005 York Drive
Norman, OK 73069
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK REFERENCE GUIDE
95.5% SINGLE STAGE MULTI-POSITION
RESIDENTAL GAS FURNACES (33” TALL)
NOTES:
This document does not replace the installation instructions, which must be referred to for
detailed information.
1. Refer to the condensate management and drain hose
plumbing for different configurations in this document. No
hose clamps are needed for the condensate pan hook up.
2. Drip leg in the gas line must be installed.
3. The furnace controls require correct polarity on the power
supply and a proper ground.
4. Y & G must be connected to the control board for cooling
operation.
5. To measure total static pressure add supply duct pressure to
the return duct pressure, add pressure drop across the ‘A’
coil, and add pressure drop across the filter. Ignore negative
signs on the readings.
6. Inlet gas pressure for natural gas should be 7” and that for
propane should be 11” w.c. Nominal manifold gas pressure
is 3.5” for natural gas and 10” w.c. for propane.
7. If thermoplastic evaporator ‘A’ coil drain pans are to be
installed in the up-flow/horizontal configuration, then extra 2”
minimum spacing may be needed to ensure against drain
pan distortion.
8. External filters required on all configurations.
9. Electrical entry is available on both sides of the casing.
10. All 33”, 95% furnaces are approved for single-pipe and 2-
pipe systems. For single pipe systems it is recommended to
install the combustion air coupling provided and install
approximately 18” of PVC pipe on the furnace.
11. Do not install an external condensate trap on these fur-
naces, as it will prevent the unit from operating correctly.
SUPPLY END
23.8”
RETURN END
2” Diameter
Vent Connection
Outlet
.56”
3”
DURING INSTALLATION,
DOORS MUST REMAIN ON
FURNACE WHEN MOVING
OR LIFING.
B
Combustion
Air Inlet
B
Clips can be flipped
into the up position
for coil cabinet or
plenum attachment
.56”
.56”
24.25”
20”
Combustion Air Inlet
Combustion Air Inlet
Airflow CFM (Bottom Return without Filters)
0.5" ESP (Nominal)
Med-Lo Med-Hi
653 818
Condensate Drain
(Downflow)
Minimum Wire
Size awg @ 75'
One-Way
Maximum
Over Current
Protection
Gas Pipe
Entry
Total Unit
Amps
Condensate Drain
(Downflow)
Models
A-COIL
Low
581
High
950
Vent Connection
Outlet
Electrical
Entry
(T,G)G9S040A08MP11
(T,G)G9S060A10MP11
(T,G)G9S060B12MP11
(T,G)G9S080B12MP11
(T,G)G9S080C16MP11
(T,G)G9S080C22MP11
(T,G)G9S100C16MP11
(T,G)G9S100C20MP11
(T,G)G9S120D16MP11
(T,G)G9S120D20MP11
(T,G)G9S130D20MP11
14
14
14
14
14
12
14
12
14
12
12
8.0
15
15
15
15
15
20
15
20
15
20
20
Vent Connection
Outlet
769
917
872
1038
1082
1179
1465
1937
1477
1712
1495
1739
1786
1103
1243
1370
1671
2162
1706
1934
1805
1977
2047
10.0
10.0
10.0
11.5
17.0
11.5
17.0
11.5
17.0
17.0
Condensate
Drain
713
23”
854
1008
1250
1586
1224
1430
1254
1430
1459
Thermostat
Wiring
838
Optional Return Air
Cutout (Either side)
1285
819
14”
1183
876
1”
33”
1190
1198
28.5”
29.5”
1.5”
RIGHT SIDE
LEFT SIDE
3
Maximum
Vent Equivalent
Time For 1 ft Natural Gas
Factory Heating
Temperature
Rise Range
1
3
Models
Follow all national, local codes and standards in addition to this document. The installation
must comply with regulations of the serving gas supplier, local building, heating, plumbing,
and other codes. In absence of local codes, the installation must comply with the national
codes and all authorities having jurisdiction.
(1030 Btu/Ft )
Seconds On (Rate)
2
Speed Setting
2"
65’
65’
65’
65’
65’
65’
30’
30’
30’
30’
N/A
3"
(T,G)G9S040A08MP11
(T,G)G9S060A10MP11
(T,G)G9S060B12MP11
(T,G)G9S080B12MP11
(T,G)G9S080C16MP11
(T,G)G9S080C22MP11
(T,G)G9S100C16MP11
(T,G)G9S100C20MP11
(T,G)G9S120D16MP11
(T,G)G9S120D20MP11
(T,G)G9S130D20MP11
90’
90’
90’
90’
90’
90’
90’
90’
90’
90’
85’
Med-Hi
High
30°F-60°F
30°F-60°F
30°F-60°F
35°F-65°F
35°F-65°F
35°F-65°F
35°F-65°F
35°F-65°F
40°F-70°F
35°F-65°F
45°F-75°F
93
62
62
46
46
46
37
37
30
30
28
A
FRONT
Med-Hi
High
CLEARANCES
DIMENSIONS
High
Application
Top
Upflow
Downflow
Horizontal
Cabinet Size
A (in)
14-1/2"
17-1/2"
21"
B (in)
Med-Hi
High
1"
0"
0"
0"
0"
0"
0"
0"
0"
0"
0"
All 'A' Cabinet Furnaces
All 'B' Cabinet Furnaces
All 'C' Cabinet Furnaces
All 'D' Cabinet Furnaces
13-3/8"
16-3/8"
19-7/8"
23-3/8"
Vent
0"
Med-Hi
High
Rear
0"
Side
1"
0"
24-1/2"
Med-Hi
High
Front*
LED INDICATOR
1
Floor
Closet
Combustible
Combustible
Yes
Combustible
1. For venting purposes, one 90° sweep elbow is equal to 5 Ft. of venting length, one 90° standard elbow is equal to 10 equiva-
lent feet of vent length. Vent termination elbows are not included in these calculations, minimum required vent length is 15 ft.
Slow Green Flash
Yes
No
Yes
No
• Normal operation
Slow Amber Flash
2. Must be changed if not in rise range.
Line Contact
Yes
• Normal operation with call for heat
Any Red Flash = Fault condition
Any Rapid 4 Flash = Potential fault codes / conditions
1. For combustible floors only when used with special
sub-base.
Subject to change without notice. Printed in U.S.A.
Copyright © 2008 by Johnson Controls, Inc. All rights reserved.
401260-URG-C-0808
Supersedes: 401260-URG-B-0708
*401260*
* 24" clearance in front and 18" on side recommended for
service access.
Johnson Controls Unitary Products
All furnaces approved for alcove and attic installation.
5005 York Drive
Norman, OK 73069
Download from Www.Somanuals.com. All Manuals Search And Download.
MOST COMMON INSTALLATION CONFIGURATIONS (MORE OPTIONS AVAILABLE WITH INDUCER ROTATION, WHICH IS COVERED IN THE INSTALLATION MANUAL)
MULTI-POSITION CONFIGURATION INFORMATION:
Ensure that all PVC venting has at least 1/4” per foot slope towards the furnace.
Furnace is multi-position and may be installed in any of the configurations shown.
1
Move rain gutter hose
to this position
AIRFLOW
The furnace condensate pan is self priming and contains an internal trap.
Do not install an external condensate trap.
When drain hose routing changes are required (shown in red), be sure to cap
all unused openings.
If rerouting hoses - excess length should be cut off so that no sagging loops will
collect and hold condensate, which will cause the furnace to not operate.
2
AIRFLOW
Move pressure switch
hose to this position.
NOTE: May require the
longer hose that is
provided with wider cabinets
1
3
Change condensate drain
connection to the 90° fitting provided
Move rain gutter hose
to this position
Rain
Gutter
Hose
HORIZONTAL LEFT
Move condensate drain hose
to this position
4
5
2
Move pressure switch
hose to this position.
NOTE: May require the
longer hose that is
provided with wider
cabinets.
Pressure
Switch
Hose
Move rain gutter hose to this position
NOTE: May require hose extension that
is provided with wider cabinets
Condensate
Drain Hose
1
Move pressure switch
hose to this position
AIRFLOW
3
Move condensate drain
hose to this position
2
DOWNFLOW
UPFLOW
Change condensate drain
connection to the 90° fitting provided
Inducer must be rotated
90° in either direction for
this installation
3
Move rain gutter hose
to this position
AIRFLOW
NOTE: Only side venting on 130K unit.
Move rain gutter
hose to this position
4
HORIZONTAL RIGHT
4
Move condensate drain hose
to this position
In upflow and downflow installation - Condensate drain hose may go out either side.
Download from Www.Somanuals.com. All Manuals Search And Download.
|