JLTDC10
Condenser dryer with heat pump
Instruction manual
Download from Www.Somanuals.com. All Manuals Search And Download.
• Risk of fire: items that have been spotted • If the machine is situated on a carpeted
or soaked with vegetable or cooking oil
constitute a fire hazard and should not be
placed in the tumble dryer.
floor, please adjust the feet in order to
allow air to circulate freely.
• After having installed the appliance, check
that it is not pressing or standing on its
electrical supply cable.
• If the tumble dryer is placed on top of a
washing machine, it is compulsory to use
the stacking kit (optional accessory).
• If you have washed your laundry with stain
remover you must execute an extra rinse
cycle before loading your tumble dryer.
• Please make sure that no gas lighters or
matches have accidentally been left in
pockets of garments to be loaded into
appliance
Use
• This appliance is designed for domestic use.
It must not be used for purposes other than
those for which it was designed.
Warning! Never stop a tumble
dry before the end of the drying
cycle unless all items are quickly
removed and spread out so that
the heat is dissipated. Risk of fire!
• Only dry fabrics which are designed to be
machine dried. Follow the instructions on
each garment label.
• Do not dry unwashed items in the tumble
dryer.
• Risk of electric shock! Do not spray
down the appliance with jets of water.
• Do not overload the appliance. See the
relevant section in the user manual.
• Clothes which are dripping wet should not
be placed in the dryer.
• Garments which have been in contact with
volatile petroleum products should not be
machine dried. If volatile cleaning fluids are
used, care should be taken to ensure that
the fluid is removed from the garment
before placing in the machine.
• Never pull the power supply cable to
remove the plug from the socket; always
take hold of the plug itself.
• Never use the tumble dryer if the power
supply cable, the control panel, the working
surface or the base are damaged so that the
inside of the tumble dryer is accessible.
• Fabric softeners, or similar products should
be used as specified by the fabric softener
instructions.
Installation
• This appliance is heavy. Care should be
taken when moving it.
• When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
• All packing must be removed before use.
Serious damage can occur to the product
and to property if this is not adhered to. See
relevant section in the user manual.
• The final part of a tumble dryer cycle occurs
without heat ( cool down cycle ) to ensure
that the items are left at a temperature that
ensures that items will not be damaged.
• Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
• Care must be taken to ensure that the
appliance does not stand on the electrical
supply cable.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
• Caution - hot surface : Do not touch the
Energy consumption depends on
spinning speed set in washing machine.
Higher spinning speed - lower energy
consumption.
door light cover surface when the light is
switched on.1)
Child safety
• This machine is not intended for use by
young children or infirm persons without
supervision.
Environmental
information
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the
packaging materials in the appropriate
container at the community waste disposal
facilities.
• This appliance is designed to be operated
by adults.
• Children should be supervised to ensure
that they do not play with the appliance.
• The packaging components (e.g. plastic
film, polystyrene) can be dangerous to
children - danger of suffocation! Keep them
out of children’s reach.
• Keep all detergents in a safe place out of
children’s reach.
Important! The heat pump of your dryer
contains a closed refrigerant circuit filled with
a refrigerant which is free from fluoro-chloro-
hydrocarbons. The refrigerant circuit in the
heat pump must not be damaged.
• Make sure that children or pets do not
climb into the drum.
Warning! When a unit is no longer
being used:
• Pull the plug out of the socket.
• Cut off the cable and plug and
dispose of them.
• Dispose of the door catch. This
prevents children from trapping
themselves inside and endangering
their lives.
Environmental tips
• In the dryer, laundry becomes fluffy and
soft. Fabric softeners are not therefore
needed when washing.
• Your dryer will function most economically
if you:
– Always keep the ventilation slots on the
base of the dryer unobstructed;
– Use the loading volumes specified in the
programme overview;
– Ensure you have good ventilation in the
installation room;
– Clean the micro-fine filter and fine
strainer after each drying cycle;
The symbol on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
– Spin the laundry well before drying.
1) Only dryers equipped with internal drum light.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
For the user
For the installer
Important safety information
Description of the appliance
Control panel
2
7
8
8
9
Technical specifications
24
Installation
25
25
25
26
26
27
Transporting the appliance
Appliance positioning
Removing transport safety packaging
Electrical connection
Door reversal
Before first use
Programme chart
Sorting and preparing laundry 11
Repairs - after sales service
28
Daily use
11
11
11
12
12
12
13
13
13
14
14
14
14
Switching machine on
Door opening and laundry loading
Selecting the programme
Extra delicate
Intensive
Long anti-crease
Alarm
Time
Delay start
Setting child lock
Starting the programme
Changing programme
Putting in extra items or taking items out
before end of programme
15
Guide to use the
Drying cycle complete / removing laundry 15
instruction manual
The following symbols will be found in the text
to guide you throughout the instructions:
Maintenance and cleaning
Cleaning fluff filter
Cleaning the door seal
Emptying the water reservoir
Cleaning heat exchanger filter
Cleaning the drum
16
16
17
17
18
20
20
Safety instructions
Hints and tips
Clean operating screen and housing
What to do if ...
Machine settings
21
23
Environmental information
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the appliance
1
2
3
4
5
7
6
8
9
11
12
10
1 Control panel
2 Water reservoir
3 Drum light
7 Rating plate
8 Course fluff filter
9 Heat exchanger cover
4 Fine fluff filter
5 Fluff filter
10 Push button for base door opening
11 Ventilation grille
6 Loading door (reversible)
12 Adjustable feet
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel
1
2
3
4
5
6 7 8
9 10
1 Programme selector and Off switch
2 Extra delicate button
3 Intensive button
7 Display (Dry time)
8 Start/Pause button
9 Warning lights: Condenser, Filter,
Full tank
10 Delay start button
4 Long anti-crease button
5 Alarm button
6 Time button
Before first use
In order to remove any residues which may
have been produced during production, wipe
the dryer drum with a damp cloth or carry out
a brief drying cycle (30 MIN) with damp cloths
in the machine.
Warning! If the appliance was not
transported in an upright position,
leave it to stand for 12 hours before
connecting it to the electricity supply
and using it for the first time, so that
the oil can flow back to the
compressor. Otherwise the
compressor could be damaged.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Additional
functions/options
Programmes
Application/properties
Thorough drying of thick or multi- layered fabrics,
e.g. terry towelling items, bathrobes, cottons.
Cottons Extra dry 7 kg
-
-
•
•
•
•
•
•
-
-
•
•
Cottons Store
Thorough drying of thick fabrics, e.g. terry
towelling items, towels, cottons.
7 kg
dry
Thorough drying of fabrics of even thicknesses,
e.g. terry towelling items, knitwear, towels, cotton
shirts.
Cottons
Cupboard dry
7 kg
-
•
•
•
-
•
1)
Cottons Damp
dry
For thin textiles which are still to be ironed, e.g.
knitted item, cotton shirts.
7 kg
-
-
•
•
•
•
•
•
•
•
•
-
-
-
•
•
•
Cottons Iron
For normal thickness cotton or linen laundry, e.g.
bedding, table linen.
7 kg
1)
dry
Synthetics Extra
dry
Thorough drying of thick or multi-layered fabrics,
e.g. pullovers, bedding, table linen.
3 kg
•
For thin fabrics which are not ironed, e.g. easy care
shirts, table linen, socks, lingerie with bones or
wires.
Synthetics
Cupboard dry
3 kg
•
•
•
•
-
•
1)
Synthetics Iron
dry
For thin fabrics which are also to be ironed, e.g.
knitwear, cotton shirts.
3 kg
•
-
•
-
•
•
•
•
-
•
•
Time
7 kg
7 kg
•
For drying of individual items of laundry.
For leisure clothing, such as jeans, sweat-shirts,
etc., of different material thicknesses (e.g. at the
neck, cuffs and seams).
Heavy cotton
-
•
•
•
-
-
•
Special program with anti-crease mechanism for
easy care fabrics such shirts and blouses; for
minimum ironing effort. The results depends on
the type of fabric and its finish. Place fabrics in the
dryer straight after spinning; once dried,
immediately remove fabrics and place on a clothes
hanger.
1 kg
(or 5
shirts)
Easy iron
-
•
•
•
•
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
functions/options
Programmes
Application/properties
For refreshing or airing clothing that has been in
storage.
Refresh
Wool
Silk
1 kg
1 kg
1 kg
-
-
-
-
•
•
•
-
•
•
•
-
-
-
•
•
•
For drying woollen fabrics after they have been
washed, using warm air at minimum mechanical
load (Follow section “Sorting and preparing
washing”). Recommendation: Remove fabrics
immediately after drying, as no anti-crease
programme follows.
For drying silk using warm air and gentle
movement.
•
1) In accordance with EN61121
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Sorting and preparing laundry
Sorting laundry
• Do not dry cotton jersey and knitwear with
the Extra programme. Items may shrink!
• Sort by fabric type:
• Wool and wool-like textiles can be dried
using the Wool programme. Before the
drying cycle spin the woollen textiles as well
as possible (max. 1200 rpm). Only dry
woollen textiles together of similar or the
same material, colour and weight. Please
dry heavy laundry items made of wool
separately.
– Cotton/linen for programmes in
Cottons programme group.
– Mixtures and synthetics for programmes
in Synthetics programme group.
• Sort by care label: The care labels mean:
Drying in the tumble dryer possible in
principle
Preparing laundry
Drying at normal temperature
• To avoid laundry becoming tangled: close
zips, button up duvet covers and tie loose
ties or ribbons (e.g. of aprons).
Drying at reduced temperature
Drying in the tumble dryer not possible
• Empty pockets. Remove metal items
(paper clips, safety pins, etc).
• Turn items with double-layered fabrics
inside out (e.g. with cotton-lined anoraks,
the cotton layer should be outermost).
These fabrics will then dry better.
Important! Do not place in the appliance
any wet laundry which is not specified on the
care label as being suitable for tumble-drying.
This appliance can be used for all wet laundry
items which are labelled as suitable for
tumble-drying.
• Do not dry new, coloured textiles together
with light-coloured laundry items. Textile
colours may bleed.
Daily use
Switching machine on
Door opening and laundry
loading
Turn the programme selector to any
programme. The machine switches on. When
the loading door is open, the internal lamp
illuminates the drum.
1. Open loading door:
Push against the loading door (push point)
Download from Www.Somanuals.c1om1. All Manuals Search And Download.
During the cycle time elapses by steps of one
minute; less than 1 hour the leading zero is not
shown (e.g. “59”, “5”, “0”).
Extra delicate
Extra delicate cycle is a programme specially
designed for drying sensitive fabrics with the
care label and for temperature-sensitive
textiles (e.g. acrylic, viscose). The programme
is executed with reduced heat. To activate it:
1. Choose the drying programme.
2. Load your laundry (do not force it in).
Caution! Do not jam laundry in
between the loading door and rubber
seal.
2. Press the Extra delicate button - the LED
above is on.
To deselect the function press the Extra
delicate button again. LED above is off.
3. Close loading door securely. Lock must
audibly lock.
Intensive
If the laundry is still damp after a standard
drying programme, you can increase the
drying result by using the Intensive function.
Selecting the programme
1. Choose the drying programme.
Use the programme selector to set the
programme you require. The estimated time
to end of the programme appears in the LCD
in h:mm format (hours:minutes).
2. Press the Intensive button - the LED above
is on.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
To deselect the function press the Intensive
– When the anti-crease phase starts or ends
button again. The LED above is off.
– When the cycle is interrupted
To activate it:
Long anti-crease
1. Choose the drying programme.
This function prolongs the anti-crease phase 2. Press the Alarm button - the LED above is
to 90 mins in total. The drum rotates in
intervals during this phase. The laundry
therefore remains relaxed and free of creases.
To activate it:
on.
1. Choose the drying programme.
2. Press the Long anti-crease button - the LED
above is on.
To deselect the function press the Alarm
button again. The LED above is off.
Time
Use the Time button to select the programme
duration after setting the Time programme.
You can select a programme duration from 10
mins to 2 hrs in 10-minute steps.
1. Turn the programme selector to the
Time programme. The flashing 10' above
the Time button is on.
If this additional function is selected, the anti-
crease phase at the end of the drying cycle is
lengthened by 60 minutes. The laundry can be
removed at any time during the anti-crease
phase.
To deselect the function press the Long anti-
crease button again. The LED above is off.
Press the Long anti-crease button. A 90 minute
anti-crease phase is set. The display now
shows the Long anti-crease icon. If this
additional function is selected, the anti-crease
phase at the end of the drying cycle is
lengthened by 60 minutes. The laundry can be
removed at any time during the anti-crease
phase.
2. Press the Time button repeatedly until the
desired programme duration is shown in
the display, e.g. 20 for a programme of 20
minutes.
If the programme duration is not selected, the
duration is automatically set to 10 mins.
Alarm
The appliance is supplied with the Alarm
function deactivated.
When activated, the buzzer sounds:
– At the end of the cycle
Download from Www.Somanuals.c1om3. All Manuals Search And Download.
– Before programme is started:
Appliance cannot be used
Delay start
– After programme is started:
Programme in operation cannot be
changed
The icon appears in the display to indicate
that the child safety device is activated.
With the Delay start button, you can
delay the start of a programme by
between 30 minutes (30') and a
maximum of 20 hours (20h).
1. Select the programme and additional
functions.
2. Press the Delay start button as many times
as necessary until the required Delay
The child safety device is not deactivated once
the programme comes to an end.
If you want to set a new programme, you must
first deactivate the child safety device.
start appears on the display, e.g. 12h if the
programme is to be started in 12 hours.
Starting the programme
If the display is showing 20h and you
press the button again, the time delay
will be cancelled. The display will show
0'and then the duration of the selected
programme.
Press the Start/Pause button. The
programme starts.
The programme progress is shown by
elapsing Dry time on LCD.
3. To activate the delay timer, press the
Start/Pause button. The amount of time
remaining until the programme is set to
start is continuously displayed (e.g. 15h,
14h, 13h, … 30' etc).
Setting child lock
The child lock can be set to prevent a
programme being accidentally started or a
programme in operation being accidentally
changed. The child lock function locks all
buttons and the programme selector. The
child lock can be activated or deactivated by
holding down the Extra delicate and Intensive
buttons simultaneously for 5 seconds.
Changing programme
To change a programme which has been
selected by mistake once the programme has
started, first turn the programme selector to
Off and then reset the programme.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
signal sounds intermittently for about one
minute.
The programme can no longer be
changed directly once the programme
has started. If nevertheless there is an
attempt to change the programme on
the programme knob, the programme
progress display and the maintenance
indicators flash. If an option button
(excluding the Alarm button) is
pressed, Err appears in the
multidisplay.
The drying cycles (except from the
Wool programme) are automatically
followed by an anti-crease phase
which lasts around 30 minutes. The
drum rotates at intervals during this
phase. This keeps the laundry loose
and free of creases. The laundry can be
removed at any time during the anti-
crease phase. (The laundry should be
taken out towards the end of the anti-
crease phase at the latest to prevent
creases from forming.) If Long anti-
crease function has been selected, the
anti-crease phase is lengthened by 60
minutes.
The drying programme is not however
affected by this (laundry protection).
Putting in extra items or
taking items out before
end of programme
1. Open loading door.
1. Open door.
Warning! Laundry and drum can
become hot. Risk of burns!
2. Before removing the laundry, remove fluff
from the micro-fine filter. It is best to use
a damp hand for this purpose. (See
“Maintenance and cleaning” chapter.)
3. Remove laundry.
2. Load or remove laundry items.
3. Close loading securely. Lock must audibly
lock.
4. Turn the programme selector to Off.
4. Press the Start/Pause button to continue
the drying cycle.
Important! After each drying cycle:
Drying cycle complete /
removing laundry
Once the drying cycle is complete, the display
shows the anti-crease icon and flashing "0" as
well as warning lamps: Filter and Full tank. If the
Alarm button has been pressed, an acoustic
- Clean the micro-fine filter and fine filter
- Drain the condensed water container
(See chapter “Maintenance and
cleaning ”.)
5. Close the door.
Download from Www.Somanuals.c1om5. All Manuals Search And Download.
Maintenance and cleaning
Cleaning fluff filter
The filters collect all the fluff which
accumulates during drying. To ensure that the
dryer works perfectly, the fluff filters (micro-
fine filter and fine strainer) must be cleaned
after every drying cycle.
The warning lamp Filter lights to remind you
of this operation at the end of each cycle.
Caution! Never operate the dryer
without fluff filters or with damaged or
blocked fluff filters.
4. Push down the unlock button on the large
mesh filter.
1. Open loading door
The large mesh filter pops up.
2. Use a damp hand to clean the micro- fine
filter, which is built into the lower part of
the loading aperture.
5. Take out fine filter.
3. After a period of time, a patina due to
detergent residue on laundry forms on
the filters. When this occurs, clean the
filters with warm water using a brush.
Remove the filter from the door pulling it
out. (It can be positioned with the
locating spur facing to the left or to the
right).
After cleaning do not forget to put it back.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Pressboth journalsof thelarge mesh filter
into the brackets on the loading door
until they snap into place.
10. Re-insert fine filter.
11. Press against the large mesh filter until it
locks into the interlock.
6. Remove the fluff from fine filter. It is best
to use a damp hand for this purpose.
Clean the entire filter area
The filter area does not have to be
cleaned after every drying cycle, but
should be checked regularly and cleaned
of fluff if necessary.
If the fine filter is not fitted, the large
mesh filter will not snap into place and
the loading door cannot be closed.
7. To do this, grip the top of the large mesh
filter and pull it forwards until it comes
loose from the two brackets.
Cleaning the door seal
Wipe the door seal with a damp cloth
immediately after the drying cycle has finished.
Emptying the water
reservoir
Empty the water reservoir after every drying
cycle.
If the water reservoir is full, an active
programme will break off automatically and
the warning lamp Full tank lights. In order to
continue the programme, the water reservoir
must first be emptied.
8. Remove fluff from the entire filter area. It
is best to use a vacuum cleaner for this
purpose.
Warning! The condensed water is
not suitable for drinking or for
preparing foodstuffs.
Download from Www.Somanuals.c1om7. All Manuals Search And Download.
1. Take out drawer containing water
reservoir completely 1 and pull up the
water reservoir's drainage pipe as far as it
will go 2.
The condensed water can be used as
distilled water, e.g. for steam ironing.
However it must first be filtered (e.g.
with a coffee filter) to remove any
residue and small pieces of fluff.
2.
Cleaning heat exchanger
filter
If the warning lamp Condenser lights, the heat
exchanger filter in the base of the appliance
must be cleaned.
1.
To protect the heat pump from dirt,
the dryer is fitted with a fluff filter,
which is located in the filter housing.
Here, too large amounts of fluff build
up over time, which affect the function
of the appliance.
2. Pour the condensed water out into a basin
or similar receptacle.
Important!
• Operating when the fluff filter is clogged
with fluff can damage the dryer. This also
increases energy consumption.
• Never operate the dryer without the fluff
filters.
1. Open door in plinth: To do this, press the
release button on the right and open the
door in the plinth to the left.
3. Slide the outlet connections in and refit
the water reservoir.
If the programme has been interrupted as
a result of the water reservoir being full:
Press the Start/Pause button to continue
the drying cycle.
The water reservoir has a volume of
approx. 4 litres. This is sufficient for
around 7 kg of laundry which has
previously been spun at 1000
revolutions / minute.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Pull the filter housing out of the base by
the handle.
1
2
1
3. Clean the inside of the door, the fluff filter
chamber and the rubber seals of fluff.
4. Remove fluff from the fluff filter on the
floor of the base with a damp hand.
6. Remove fluff from the fluff filter with a
damp hand. If necessary, clean the filter
under running water using a brush.
5. To clean the fluff filter: Remove the filter
from the filter housing. To do this, press
the pressure points on the sides and pull
the filter frame up and out of the housing.
7. Insert the fluff filter into the filter housing.
8. As necessary, approx. once every 6
months, remove the fluff from the heat
exchanger using the sponge supplied.
When doing this, please use rubber
gloves.
Download from Www.Somanuals.c1om9. All Manuals Search And Download.
Lime in the water or cleaning agents
may form a barely visible lining on the
inside of the drum. The degree to
which the laundry has been dried is
then no longer detected reliably. The
laundry is damper than expected when
removed from the dryer.
Use a standard domestic cleaner (e.g.
vinegar-based cleaner) to wipe down
the inside of the drum and drum ribs.
Clean operating screen
and housing
The fluff can be removed more easily
if it is first dampened e. g. with a
laundry dampener. It is best to use a
vacuum cleaner for this purpose.
Do not use any sharp objects in
this area.
Caution! Do not use furniture
cleaners or aggressive cleaning agents
to clean the machine.
Use a damp cloth to wipe down the
operating screen and housing.
9. Re-insert filter housing along with filter in
appliance base.
If the fluff filter is not inserted in the filter
housing, the filter housing cannot be slid
into the appliance base.
10. Close door in plinth.
Cleaning the drum
Caution! Do not use abrasives or
steel wool to clean the drum.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
What to do if ...
If, during operation, the error code E... plus the error is still displayed, please inform your
number or letter) appears on the LCD: Switch local Service Force Centre and quote the
the machine off and on again to reset the
error code.
programme. Press the Start/Pause button If
Problem
Possible cause
Remedy
Plug in at mains socket. Check
fuse in fuse box (domestic
installation).
Mains plug is not plugged in or
fuse is not working correctly.
Dryer does not work.
Loading door is open.
Close loading door.
Have you pressed the Start/
Pause button?
Press the Start/Pause button
again.
Select a different programme the
next time you dry (see
Wrong programme selected.
“Programme chart” chapter).
Lint filters clogged.
Fluff filter clogged.
Clean lint filters.
Clean fluff filter.
Observe recommended loading
volumes.
Overloading of laundry.
Drying results unsatisfactory.
Ventilation slots in base area
covered up.
Uncover ventilation slots in base
area.
Clean inside surface of drum and
drum ribs.
Residue on inside surface of
drum or drum ribs.
Make an adjustment using the
DRYNESS function (see
chapter ”Daily use”)
Fine strainer not in place and/or Install fine strainer and/or snap
mesh filter not locked in place. large mesh filter into place.
Loading door does not close.
Washing protection. After the
Turn the programme knob to
start of the programme, the
Off. Set the programme again.
option can no longer be set.
When a button is pressed, Err
appears on the LCD.
Programme selector in Off
position.
Turn programme selector to
LIGHT or to any programme.
Drum light does not work.
Replace light bulb (see next
section).
Defective light bulb.
Download from Www.Somanuals.c2om1. All Manuals Search And Download.
Programme time is corrected
Displayed programme time
changes erratically or stays
unchanged for a long time.
automatically depending on type Automatic process; this is not a
and volume of laundry and level machine fault.
of dampness.
Programme inactive, empty
water tank warning lamp Full
tank lights.
Empty the water reservoir, then
start programme with Start/
Pause button.
The water reservoir is full.
Select time programme or higher
drying level (e.g. INTENSIVE
DRY instead of STORAGE
DRY).
Drying cycle ends shortly after
programme starts. END display washing loaded is too dry for
illuminated.
Not enough washing loaded or
selected programme.
Lint filter clogged.
Fluff filter clogged.
Load volume too big.
Clean lint filter.
Clean fluff filter.
Drying cycle lasts an unusually
long time. Note: After around 5
hours the drying cycle ends
automatically (see „Drying cycle
complete ”).
Reduce load volume.
Laundry must be adequately
spun.
Laundry insufficiently spun.
Particularly high room
temperature. Temporary
Automatic process, there is no
fault with the appliance. If
switching off of the compressor possible, lower the room
to avoid overload.
temperature.
1. Unscrew the cover above the bulb (this
can be found directly behind the loading
aperture, at the top; refer to “Description
of machine” section.)
2. Replace the defective bulb.
3. Screw cover back down.
Replacing the drum light
Only use a special bulb which is designed
specially for dryers. The special bulb can be
obtained from your local Service Force
Centre.
Check the correct positioning of o-ring gasket
before screwing back the door light cover. Do
not operate the dryer when missing o-ring
gasket on door light cover.
Important! When the appliance is switched
on, the interior lighting switches itself off after
4 minutes when the door is open.
Warning! Do not use standard bulbs!
These develop too much heat and may
damage the machine!
Warning! For safety reasons, the
cover must be screwed down tightly.
If this is not done, the dryer must not
be operated.
Warning! Before replacing the bulb,
disconnect the mains plug; with a
permanent connection: fully unscrew
or deactivate the fuse.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Machine settings
ALARM permanent on/off
The alarm is by default always off. To set
permanent alarm on (off):
1. Turn the programme selector to any
programme.
2. Press simultaneously the Intensive and
Long anti-crease buttons and hold
down for approx. 5 seconds.
Adjusting the level of conductivity
3. Press the Start/Pause button until you
Water contains, a variable quantity of
limestone and mineral salts of which
quantities vary according to geographical
locations thus varying its conductivity
values.
Relevant variations of the conductivity of
the water compared to those prefixed by
the factory could slightly influence the
residual humidity of the laundry at the
end of the cycle. Your dryer allows you to
regulate the sensitivity of the drying
sensor based on conductivityvalues of the
water.
set desired level:
low conductivity
<300 µS/cm
medium conductivity
300-600 µS/cm
high conductivity
>600 µS/cm
4. To memorize setting press simultaneously
the Long anti-crease and Start/
Pause buttons or turn knob to Off
position
1. Turn the programme selector to any
programme.
2. Press simultaneously the Long anti-
crease and Start/Pause buttons and
hold down for approx. 5 seconds.
Download from Www.Somanuals.c2om3. All Manuals Search And Download.
Technical specifications
This appliance conforms with the following EU Directives:
– 2006/95/EC dated 12.12.2006 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive
92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Height x width x depth
Drum volume
85 x 60 x 58 cm
108 l
Depth with loading door open
Height can be adjusted by
Weight when empty
109 cm
1.5 cm
approx. 60 kg
max. 7 kg
230-240 V
13 A
1)
Loading volume (depends on programme)
Voltage
Required fuse
Total power
1350 W
A
Energy efficiency class
Energy consumption (7 kg of cotton, pre-
drained at 1000 rpm)
2,4 kWh
2)
Use
Domestic
Permissible ambient temperature
+ 5°C to + 35°C
Consumption values
The consumption values have been established under standard conditions. They may deviate when
the machine is operated in domestic circumstances.
Programme
Energy consumption in kWh
2) 3)
2.4
COTTON CUPBOARD DRY
2) 3)
1.8
COTTON IRON DRY
2) 4)
0.75
SYNTHETICS CUPBOARD DRY
1) Different loading volume data may be needed in some countries as a result of different measuring methods.
2) in accordance with IEC 61121
3) 7 kg load pre-drained at 1000 rpm
4) 3 kg load pre-drained at 1200 rpm
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
• Air must be able to circulate freely all round
the appliance. Do not obstruct the front
ventilation grille or the air intake grilles at
the back of the machine.
• To keep vibration and noise to a minimum
when the dryer is in use, it should be placed
on a firm, level surface.
Transporting the
appliance
Important! Only tip the appliance on its left
side to transport (see illustration), if it cannot
be transported in an upright position.
• Once in its permanent operating position,
check that the dryer is absolutely level with
the aid of a spirit level. If it is not, raise or
lower the feet until it is.
• The feet must never be removed. Do not
restrict the floor clearance through
deeppile carpets, strips of wood or similar.
This might cause heat built-up which would
interfere with the operation of the
appliance.
Important! The hot air emitted by the
tumble dryer can reach temperatures of up to
60°C. The appliance must therefore not be
installed on floors which are not resistant to
high temperatures.
When operating the tumble dryer, the room
temperature must not be lower than +5°C
and higher than +35°C, as it may affect the
performance of the appliance.
Warning! Should the appliance be
moved, it must be transported
vertically.
Appliance positioning
• It is recommended that, for your
convenience, the machine is positioned
close to your washing machine.
Warning! The appliance must not be
installed behind the lockable door, a
sliding door a door with a hinge on the
opposite side to that of the appliance.
• The tumble dryer must be installed in a
clean place, where dirt does not build up.
Download from Www.Somanuals.c2om5. All Manuals Search And Download.
Removing transport
safety packaging
Electrical connection
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Caution! Before use all parts of the
transport packaging must be removed.
Warning! THIS APPLIANCE
MUST BE EARTHED.
1. Open loading door
Should the appliance power
supply cable need to be replaced,
this must be carried out by a
Service Force agent (see
chapter: Repairs - after sales
service).
2. Pull off adhesive strips from inside
machine on top of drum.
The manufacturer declines any
liability should this safety
measure not be observed.
Before switching on, make sure the electricity
supply voltage is the same as that indicated on
the appliance’s rating plate. (See picture on
page 6).
The appliance is supplied with a 13amp plug
fitted. In the event of having to change the fuse
in the plug supplied, a 13amp ASTA approved
BS 1363/A fuse must be used.
3. Remove foil hose and polystyrenepadding
from the machine.
Should the plug need to be replaced for any
reason, proceed as described below. The
wires in the mains lead are coloured in
accordance with the following code:
• Green and Yellow - Earth
• Blue - Neutral
• Brown - Live
Warning! If the appliance was not
transported in an upright position,
leave it to stand for 12 hours before
connecting it to the electricity supply
and using it for the first time, so that
the oil can flow back to the
compressor. Otherwise the
compressor could be damaged.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning! The plug must still be
accessible after the appliance
has been installed.
GREEN &YELLOW
Warning! The appliance should
not be connected to the
electrical supply by means of an
extension cable.
Warning! The manufacturer
declines any responsibility for
damage or injury through failure
to comply with the above safety
precautions.
BROWN
BLUE
CORD CLAMP
Should the appliance power
supply cable need to be replaced,
this must be carried out by our
Service Centre.
If you fit your own plug, the colours of the
wires in the mains lead of your appliance may
not correspond with the markings identifying
the terminals in your plug.
Proceed as follows:
Warning! The power supply
cable must be accessible after
installing the machine.
1. Connect the Green and Yellow (earth)
wire to the terminal in the plug which is
marked with the letter "E" or the earth
symbol
or coloured green and yellow.
Permanent connection
2. Connect the Blue (neutral) wire to the
terminal in the plug which is marked with
the letter "N" or coloured black.
3. Connect the Brown (live) wire to the
terminal in the plug which is marked with
the letter "L" or coloured red.
4. Upon completion there must be no cut,
or stray strands of wire present and the
cord clamp must be secure over the outer
sheath.
In the case of permanent connection it is
necessary that you install a double pole switch
between the appliance and the electricity
supply (mains), with a minimum gap of 3mm
between the switch contacts and of a type
suitable for the required load in compliance
with the current electrical regulations.
The switch must not break the yellow and
green earth cable at any point.
Door reversal
To make it easier to load or unload the
laundry, the door can be reversed.
Warning! A cut off plug inserted
into a 13 amp socket is a serious
safety (shock) hazard.
Ensure that the cut off plug is
disposed of safely.
Warning! The door must only be
reversed by an authorised service
engineer.
Download from Www.Somanuals.c2om7. All Manuals Search And Download.
Please contact your nearest John Lewis
branch who will give you details of your local
Service Force Centre. The engineer will carry
out the door reversal at your cost.
Repairs - after sales service
Ifthe unlikelyevent ofyourappliancerequiring So that you always have these numbers at
service, or if you wish to purchase spare parts, hand, we recommend that you make a note
please contact our extended warranty
of them here:
administrators by telephoning: 0870 010
Mod.: ...............................................................
7887 They will give you details of your local PNC: ................................................................
Service Force Centre.
S.No.: ...............................................................
Before calling out an engineer, please ensure Your dryer is covered by a 3 year parts and
you have read the details under the heading
labour guarantee (see separate details given at
“What to do if…” . When you contact your point of sale). Please retain your purchase
local repair agent you will need to give the
following details:
receipt safely for the service engineer to verify
the purchase details.
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of fault.
4. The purchase date (found on your
receipt).
Spare parts
An authorised service engineer should service
this product and only genuine spare parts
should be used.
Under no circumstances should you attempt
torepair the machine yourself. Repairscarried
out by inexperienced persons may cause
injury or serious malfunctioning. Contact your
local repair agent by telephoning:
0870 010 7887
5. The model and serial number of the
appliance (found on the rating plate - see
picture).
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.c2om9. All Manuals Search And Download.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.c3om1. All Manuals Search And Download.
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
136904440-02-07042008
Download from Www.Somanuals.com. All Manuals Search And Download.
|