S P E C I F I C A T I O N S
D O Z E R
700H
C O N S T R U C T I O N E Q U I P M E N T D I V I S I O N
Engine
700H LT / 700H XLT / 700H LGP
Type...................................................................................................John Deere POWERTECH® 6068T with turbocharger
Rated power ......................................................................................115 SAE net hp (86 kW) / 123 SAE gross hp (92 kW) @ 2,100 rpm
Cylinders, wet sleeve .........................................................................6
Displacement.....................................................................................414 cu. in. (6.8 L)
Fuel consumption, typical...................................................................2.4 to 4.8 gal./hr. (9.1 to 18.2 L/h)
Maximum net torque..........................................................................410 lb.-ft. (525 Nm) @ 1,300 rpm
Lubrication.........................................................................................pressure system with full-flow spin-on filter and oil-to-water cooler
Air cleaner .........................................................................................dual stage dry type with safety element, precleaner, and dash-mounted restriction indicator
Electrical system................................................................................24 volt with 55-amp alternator
Cooling fan.........................................................................................blower-type
Transmission
Dual-path, electronic-controlled, hydrostatic drive; load-sensing feature automatically adjusts ground speed and power to match changing load conditions; each track is
powered by a variable-displacement piston pump and motor combination; decelerator controls speed from 5.5 mph (8.9 km/h) to stop
Travel speeds (infinitely variable)
Forward and reverse....................................................................0 to 5.5 mph (0 to 8.9 km/h)
Reverse speed ratio control .........................................................80, 100, 115, and 130% of forward speed to maximum of 5.5 mph (8.9 km/h)
Final Drives
Heavy-duty triple-reduction final drives attach directly to the mainframe, isolated from the track frame and dozer frame loads
Steering
Single-lever steering, speed, and direction control, and counterrotation; full power turns and infinitely variable track speeds provide unlimited maneuverability and optimum
control; hydrostatic steering eliminates steering clutches and brakes
Brakes
Hydrostatic (dynamic) braking stops the machine whenever the direction-control lever is moved to neutral, whenever the decelerator is depressed to the end of travel, or
whenever the brake pedal is depressed
Automatic Park Brake
Exclusive safety feature engages wet, multiple-disc brakes whenever the engine stops, whenever the operator applies the brake pedal, or whenever the park lock lever is
placed in the start position; machine cannot be driven with brake applied, reducing wear out or need for adjustment
Hydraulic System
System...............................................................................................open center
Pressure, main relief ..........................................................................3,200 psi (22 064 kPa)
Pump .................................................................................................gear-type, fixed-displacement pump
Flow...................................................................................................25 gpm (95 L/min.) @ 2,100 rpm
Filter, return oil...................................................................................10 micron
Control...............................................................................................T-bar three function
Cylinders............................................................................................heat-treated, chrome-plated, polished cylinder rods with hardened steel (replaceable bushings) pivot pins
Capacities (U.S.)
Fuel tank with lockable cap ...............................................................60 gal. (227 L)
Cooling system with coolant recovery tank ........................................5.6 gal. (21 L)
Engine oil including spin-on filter .......................................................20 qt. (19 L)
Transmission reservoir refill including spin-on filter............................17.2 gal. (65 L)
Final drive (each)................................................................................14 qt. (13 L)
Hydraulic reservoir refill including spin-on filter .................................13.5 gal. (51 L)
4000S John Deere Winch, if equipped................................................10 gal. (38 L)
All powertrain and hydraulic systems allow maximum 45-degree off-level operation.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SAE Operating Weights
700H LT
700H XLT
700H LGP
With standard equipment, rollover protective (ROPS)
canopy, full fuel tank, and 175-lb. (79 kg) operator
With 120-in. (3048 mm) blade and 20-in. (510 mm)
track shoes............................................................................25,800 lb. (11 703 kg)
With 120-in. (3048 mm) blade and 22-in. (560 mm)
track shoes ...................................................................................................................................26,790 lb. (12 152 kg)
With 132-in. (3353 mm) blade and 30-in. (760 mm)
track shoes...........................................................................................................................................................................................27,900 lb. (12 653 kg)
Dimensions
700H LT
700H XLT
700H LGP
Rounded to the nearest whole number.
A
B
Overall height with canopy or cab..........................................118 in. (2985 mm)
Overall length with canopy.....................................................178 in. (4509 mm)
Overall length with cab..........................................................180 in. (4580 mm)
Overall length with retrieval hitch ..........................................179 in. (4552 mm)
Overall length with extended drawbar....................................193 in. (4905 mm)
Ground clearance, minimum
118 in. (2985 mm)
185 in. (4693 mm)
188 in. (4765 mm)
186 in. (4736 mm)
200 in. (5089 mm)
118 in. (2985 mm)
185 in. (4693 mm)
188 in. (4765 mm)
186 in. (4736 mm)
200 in. (5089 mm)
C
D
With single-bar grouser (excludes grouser
height).......................................................................15 in. (381 mm)
15 in. (381 mm)
15 in. (381 mm)
With swamp shoes (includes shoe height) ......................................................................................................................................17.6 in. (447 mm)
E
F
G
Blade lift height .....................................................................36 in. (909 mm)
Blade digging depth...............................................................20 in. (500 mm)
Blade cutting edge angle, variable adjustment range..................7 degrees
39 in. (980 mm)
21 in. (541 mm)
7 degrees
39 in. (980 mm)
21 in. (541 mm)
7 degrees
H-Series Blade Specs
700H LT
700H XLT
120 in. (3048 mm)
3.44 cu. yd. (2.63 m3)
39 in. (998 mm)
45 in. (1140 mm)
25 degrees
700H LGP
132 in. (3353 mm)
3.75 cu. yd. (2.87 m3)
39 in. (998 mm)
45 in. (1140 mm)
25 degrees
H
Width.........................................................................................120 in. (3048 mm)
SAE capacity ..............................................................................3.44 cu. yd. (2.63 m3)
Height (at ends)..........................................................................39 in. (998 mm)
Top of spill sheet (center section) ...............................................45 in. (1140 mm)
Blade angle, right and left ..........................................................25 degrees
Angled width ..............................................................................109 in. (2769 mm)
Tilt..............................................................................................17 in. (424 mm)
Cut reach
I
J
K
L
109 in. (2769 mm)
17 in. (424 mm)
121 in. (3073 mm)
18 in. (467 mm)
M
With 20-in. (510 mm) shoes.......................................................2 in. (51 mm)
With 22-in. (560 mm) shoes ..............................................................................................................1 in. (25 mm)
With 30-in. (760 mm) shoes......................................................................................................................................................................– 1 in. (– 25 mm)
N
O
Width over track.........................................................................90 in. (2286 mm)
Cast reach
92 in. (2338 mm)
108 in. (2743 mm)
With 20-in. (510 mm) shoes.......................................................16 in. (401 mm)
With 22-in. (560 mm) shoes ..............................................................................................................15 in. (375 mm)
With 30-in. (760 mm) shoes......................................................................................................................................................................13 in. (330 mm)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
A
D
I
Ground Line
E
L
G
F
H
Concrete Level
B
2.0 in. (51 mm)
single grouser height
C
J
Cut Reach
M
R
N
Width Over Track
K
O
Cast Reach
Q
P
Forestry Application
700H LT
700H XLT
700H LGP
Available limb risers and screens for the rollover protective cab and canopy structures; John Deere-built, self-contained 4000S Winch* for versatile skidding and clearing
200
operations
45
P
Q
Overall length with 4000S Winch .....................208 in. (5283 mm) 215.3 in. (5467 mm) 215.3 in. (5467 mm)
700H
180
160
140
120
100
80
Additional length with 4000S Winch to (B).......30.5 in. (775 mm) 30.5 in. (775 mm)
Additional length with 4000S fairlead to (P).....10 in. (254 mm) 10 in. (254 mm)
30.5 in. (775 mm)
10 in. (254 mm)
122 in. (3099 mm)
40
35
30
25
20
15
10
5
LT, XLT, AND LGP
R
Overall height with limb risers..........................122 in. (3099 mm) 122 in. (3099 mm)
*See 4000S Winch specifications sheet.
Drawbar Pull
Drawbar pull versus ground speed...........................usable pull will depend on traction and weight of tractor
60
40
20
0
0
0
km/h
mph
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
SPEED
19
Download from Www.Somanuals.com. All Manuals Search And Download.
700H Dozer
Key: G Standard equipment L Optional or special equipment
✶See your John Deere dealer for further information.
LT XLT LGP Operator’s Station (continued)
LT XLT LGP
Engine
LT XLT LGP Electrical (24-volt system) (continued)
G G G 115-hp (86 kW) turbocharged, isolation mounted
G G G Oil-to-water engine oil cooler
G G G Vertical spin-on oil filter
G G G Vertical spin-on fuel filters with water separator
G G G Dual-element dry air cleaner with built-in pre-
cleaner and evacuator valve
G G G Above-hood pre-screener/raincap
L L L External primary precleaner✶
G G G Enclosed safety fan guard (conforms to SAE J1308)
G G G Coolant recovery tank
G G G Dual 12-volt low-maintenance batteries, 190-min.
reserve capacity, 950 CCA
G G G 55-amp sealed alternator with cab or canopy
L L L Power port, 12 volt, 20 amps, for phone and radio
Hydraulic System
G G G 25-gpm fixed-displacement hydraulic gear pump
L L L Pump with through-drive for winch or auxiliary
pump
G G G Low-effort T-bar blade control
G G G Independent hydraulic reservoir with sight gauge
G G G Vertical spin-on hydraulic filter
G G G O-ring face seal hydraulic connectors
G G G Three-function hydraulic valve
L L L Four- and five-function valves with levers, with-
out float
Adjustable leg support / Seat belt, 2 in. (51 mm),
retractable with CRS (conforms to SAE J386)
L L L Deluxe comfort control mechanical suspension
seat, vinyl or cloth (conforms to SAE J899): Fore
and aft/weight and height combined adjustment /
Adjustable leg support / Adjustable backrest
angle / Adjustable lumbar support / Adjustable
seatback extension / Seat belt, 3 in. (76 mm),
retractable with CRS (conforms to SAE J386)
L L L Deluxe comfort control air suspension seat,
vinyl or cloth (conforms to SAE J899): Fore and
aft/weight and height combined adjustment /
Adjustable leg support / Adjustable backrest
angle / Adjustable lumbar support / Adjustable
seatback extension / Seat belt, 3 in. (76 mm),
retractable with CRS (conforms to SAE J386)
L L L Seat belt, 3 in. (76 mm), retractable with CRS
(conforms to SAE J386)
G G G Convex interior rearview mirror
L L L Rear attachment mirror (for cab only)
L L L Accessories: Convex wide-angle interior rearview
mirror / Leg cushions (2) / Seat-side lockable
storage box/lunch box/cup holder
L L L Rear window wiper and washer for cab
L L L Radio, AM/FM weatherband with digital clock
and antenna
Overall Vehicle
G G G One-piece unitized construction mainframe
G G G Front tow loop (bolt-on)
G G G Reinforced engine and mid-frame bottom guards
G G G Integral transmission guard
G G G Heavy-duty louvered grille
G G G Perforated engine side shields
G G G Vandal protection lock provisions for: Engine
service access cover / Fuel fill / Hydraulic reser-
voir fill/check / Transmission reservoir fill/check /
Instrument panel
G G G Solid hood (painted gray for reduced glare)
G G G Lockable grease gun/tool storage compartment
in right access door
G G G Blower-type cooling fan
G G G Trash-resistant seven-fin in-line radiator
G G G Under-hood muffler with vertical exhaust stack
G G G Pre-wired for ether start aid
L L L Electric ether start aid
L L L Radiator sand screen (steel)
L L L Rear auxiliary plumbing
L L L Engine coolant heater, 1,000 watts, 110 volts
L L L Engine coolant heater, fuel fired
Undercarriage
70-in. (1778 mm) track gauge, 95-in. (2413 mm)
track on ground
G
Powertrain and Controls
G G G Dual-path hydrostatic transmission
G G G Single-lever steering, speed, and direction control
G G G Decelerator pedal with automatic retardation
G G G Engine-speed selection lever
G G G Automatic tracking control
G G G Dynamic braking (anti-free wheel)
G G G Counterrotation
G G G Transmission neutral lock with safety start switch
G G G Spring-applied, hydraulic-released parking brake
G G G Independent transmission oil reservoir with
sight gauge
G G G Onboard diagnostics with visual code display
G G G Oil-to-air transmission oil cooler
G G G Built-in final drive seal guards
G G G Triple-reduction final drives with wet multi-disc
brakes
G
70-in. (1778 mm) track gauge, 102-in. (2591 mm)
track on ground
G 78-in. (1981 mm) track gauge, 102-in. (2591 mm)
track on ground
G G G Double-flange rollers
G G G Oscillating track frame with pinned front crossbar
G G G Full-length smooth-surface track-frame covers
G G G Chain guides, front and rear (bolt-on)
G G G Fully protected track-tension adjusters (grease
adjustable)
G G G Segmented sprockets
L L L Sprocket rock guards (bolt-on)
L L L Bolt-on full-length track-roller rock guards
G G G Sealed and lubricated track chains
G L L 20-in. (510 mm) extreme-service, single-bar
grousers
G G G Max. forward/reverse speed 5.5 mph (8.9 km/h)
G G G Selectable reverse speed ratio setting of 80, 100,
115, or 130% of forward speed
L G L 22-in. (560 mm) extreme-service, single-bar
grousers
L 24-in. (610 mm) extreme-service, single-bar
grousers
G 30-in. (760 mm) extreme-service, single-bar
grousers
L Swamp shoes, 30-in. (760 mm), self-cleaning
pyramid
L L L Remote diagnostic test ports
C-Frames and Blades
G G G Six-way all-hydraulic heavy-duty C-frame with
infinitely adjustable blade pitch
G G G Remote C-frame pivot grease banks
G G G Cordura-covered hoses with replaceable lengths
G G G Straight end bits
L L L Environmental drains
L L L Chrome exhaust stack
L L L Manuals/trademarks/decals, French or Spanish
L L L Transport lift and tie-down rings✶
Lights (optional)
L L L Grille-mounted high-intensity lights (2), with
rear light (1), halogen, 50 watts each
L L L High-intensity work lights, front (2) and rear (2),
with steel guards, 50 watts each
Operator’s Station
G G G Modular ROPS/FOPS canopy, isolation mounted
(conforms to SAE J1040)
L L L Under-seat canopy heater, 30,000 Btu/hr.
L L L Modular ROPS/FOPS cab, isolation mounted
(conforms to SAE J1040): Fresh air intake cab
heater/defroster/pressurizer, 18,000 Btu/hr. with
air precleaner / Dome light / Deluxe headliner
with molded air ducts for heater, defroster, and
air conditioner / 30,000-Btu/hr. under-seat heater /
Front windshield and doors, wipers and washers /
Tinted safety glass
L L L Air conditioning, 24,000 Btu/hr.
G G G Right and left operator station entry
G G G Slip-resistant front-mounting steps
G G G Ergonomically located handholds
G G G Headliner and floormat
Protection Packages
G G
Blade, 120-in. (3048 mm), with heavy-duty C-frame
G Blade, 132-in. (3353 mm), with heavy-duty C-frame
Blade, 132-in. (3353 mm), with heavy-duty
C-frame✶
L L L Extreme-duty louvered grille and hose protection
L L L Limb risers, arched or point-to-point (bolt-on)
L L L Operator-protective rear screen (canopy or cab)
L L L Operator-protective side screens (canopy or cab)
L L L Operator-protective full-screen package (canopy
or cab)
L L L Heavy-duty engine air-intake guard
L L L Extreme-service rear tank guard
L L L Air-conditioning module guard
L L
Electrical (24-volt system)
G G G Fuse panel with blade-style multi-fused circuit
breakers
G G G Horn, electric (conforms to SAE J994, J1446)
G G G Reverse warning alarm (conforms to SAE J994,
J1446)
G G G Fuel gauge, electric, illuminated
G G G Hourmeter, electric
G G G Transmission oil pressure gauge, illuminated
G G G Master electrical disconnect
G G G Positive battery terminal covers with battery cover
G G G By-pass start safety cover at starter
G G G Electronic monitor with visual and audible
warning: Alternator / Hydraulic filter restric-
tion / Transmission filter restriction / Transmis-
sion oil temperature / Coolant temperature
(audible) / Engine coolant temperature gauge /
Engine oil pressure (audible) / Engine oil pres-
sure gauge / Air cleaner restriction / Fasten seat
belt / Park brake
L L L Lift cylinder guards
Attachments
L L L Counterweight, front, 380 lb. (172 kg)
L L L Counterweight, rear✶
L L L Retrieval hitch with pin
L L L Extended rigid drawbar with pin for pull-type
implements
L L L Drawbar, extended for winch (with or without
Fairlead)
L L L Ripper, parallelogram with five shank pockets
and three teeth
L L L Winch, John Deere 4000S, power in/free spool
out OR power out
L L L Four-roller fairlead for winch
L L L Root-rake blade attachment
L L L Rear-mounted toolbox
G G G Adjustable footrests and full-length armrests
G G G Built-in Operator’s Manual storage
G G G Suspension vinyl seat (conforms to SAE J899): Fore
and aft/weight and height combined adjustment /
G G G Ground-speed selection display
Net engine power is with standard equipment including air cleaner, exhaust
Specifications and design subject to change without notice. Wherever applicable, specifications
system, alternator, and cooling fan, at standard conditions per SAE J1349
and DIN 6270B, using No. 2-D fuel at 35 API gravity. No derating is required
up to 10,000-ft. (3050 m) altitude. Gross power is without cooling fan.
are in accordance with SAE standards. Except where otherwise noted, specifications are based
on units with standard equipment, rollover protective structures, full fuel tanks, and 175-lb.
(79 kg) operators; 700H LT unit with 120-in. (3048 mm) blade and 20-in. (510 mm) track
shoes; 700H XLT unit with 120-in. (3048 mm) blade and 22-in. (560 mm) track shoes; and
700H LGP unit with 132-in. (3353 mm) blade and 30-in. (760 mm) track shoes.
DKA700H Litho in U.S.A. (02-03)
Download from Www.Somanuals.com. All Manuals Search And Download.
|