This .pdf document is bookmarked
Operating Instructions and Parts Manual
14-inch Woodworking Band Saw
Models: JWBS-14OS, JWBS-14CS
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086
Ph.: 800-274-6848
Part No. M-708115
Revision C1 02/2010
Copyright © 2010 Walter Meier (Manufacturing) Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Warranty and Service..........................................................................................................................2
Warning .............................................................................................................................................4
Introduction ........................................................................................................................................6
Specifications .....................................................................................................................................6
Unpacking – JWBS-14OS ...................................................................................................................7
Contents of the Shipping Container ..................................................................................................7
Fasteners .......................................................................................................................................7
Unpacking – JWBS-14CS ...................................................................................................................8
Contents of the Shipping Container ..................................................................................................8
Fasteners .......................................................................................................................................8
Assembly of JWBS-14OS....................................................................................................................9
Assembly of JWBS-14CS..................................................................................................................12
Grounding Instructions ......................................................................................................................14
115 Volt Operation ........................................................................................................................15
230 Volt Conversion ......................................................................................................................15
Extension Cords............................................................................................................................16
Adjustments .....................................................................................................................................16
Tilting the Table.............................................................................................................................16
Adjusting 90° Table Stop................................................................................................................16
Changing Blades...........................................................................................................................17
Adjusting Blade Tension ................................................................................................................17
Adjusting Blade Tracking ...............................................................................................................18
Adjusting Upper Blade Guide Assembly..........................................................................................18
Adjusting Blade Guide and Blade Support Bearing ..........................................................................19
Troubleshooting JWBS-14CS/OS Band Saw ......................................................................................21
Optional Accessories ........................................................................................................................22
Replacement Parts ...........................................................................................................................22
Body Assembly (JWBS-14CS/OS Band Saw)..................................................................................23
Body Assembly (JWBS-14CS/OS Band Saw)..................................................................................24
Body Assembly (JWBS-14CS/OS Band Saw)..................................................................................25
Closed Stand Assembly (JWBS-14CS Band Saw)...........................................................................26
Closed Stand Assembly (JWBS14-CS Band Saw)...........................................................................27
Open Stand Assembly (JWBS-14OS Band Saw).............................................................................28
Open Stand Assembly (JWBS-14OS Band Saw).............................................................................29
Electrical Connections – 115 volt (JWBS-14CS/OS Band Saw)............................................................30
Electrical Connections – 230 volt (JWBS-14CS/OS Band Saw)............................................................31
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
1. Read and understand the entire owner’s manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This band saw is designed and intended for use by properly trained and experienced personnel only.
If you are not familiar with the proper and safe operation of a band saw, do not use until proper
training and knowledge have been obtained.
5. Do not use this band saw for other than its intended use. If used for other purposes, Walter Meier
(Manufacturing) Inc., disclaims any real or implied warranty and holds itself harmless from any injury
that may result from that use.
6. Always wear approved safety glasses/face shields while using this band saw. Everyday eyeglasses
only have impact resistant lenses; they are not safety glasses.
7. Before operating this band saw, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips
are recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
•
•
•
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
16. Make sure the band saw is firmly secured to the stand, or bench, before use.
17. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
18. Provide for adequate space surrounding work area and non-glare, overhead lighting.
19. Keep the floor around the machine clean and free of scrap material, oil and grease.
20. Keep visitors a safe distance from the work area. Keep children away.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
21. Make your workshop child proof with padlocks, master switches or by removing starter keys.
22. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
23. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other
moving parts. Do not overreach or use excessive force to perform any machine operation.
24. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
25. Use recommended accessories; improper accessories may be hazardous.
26. Maintain tools with care. Keep blade sharp and clean for the best and safest performance. Follow
instructions for lubricating and changing accessories.
27. Make sure the work piece is held firmly against the rip fence or miter gauge as it is fed through the
blade.
28. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do
not use your hands.
29. Do not stand on the machine. Serious injury could occur if the machine tips over.
30. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
31. Remove loose items and unnecessary work pieces from the area before starting the machine.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.
- - SAVE THESE INSTRUCTIONS - -
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and
maintenance procedures for a Model JWBS-14OS and JWBS-14CS Band Saw. This manual contains
instructions on installation, safety precautions, general operating procedures, maintenance instructions
and parts breakdown. This machine has been designed and constructed to provide years of trouble free
operation if used in accordance with instructions set forth in this manual. If there are any questions or
comments, please contact either your local supplier or Walter Meier. Walter Meier can also be reached at
Specifications
Model Number:......................................................JWBS-14OS.........................................JWBS-14CS
Stock Number .............................................................. 708113.............................................. 708115K
Cutting Capacity (height/in.) ....................................................6..........................................................6
Cutting Capacity (width/in.).............................................. 13-1/2.................................................. 13-1/2
Minimum Blade Width (in.) ...................................................1/8.......................................................1/8
Maximum Blade Width (in.)...................................................3/4.......................................................3/4
Blade Length (in.) ........................................................... 93-1/2.................................................. 93-1/2
Blade Speed (SFPM) ........................................................ 3000.................................................... 3000
Table Size (in.) ..............................................................15 x 15.................................................15 x 15
Table Slot Size (DxW/in.) .............................................3/8 x 3/4...............................................3/8 x 3/4
Table Height From Floor (in.).................................................44.................................................. 43-1/2
Table Tilt (deg.) ..................................................45 right, 10 left......................................45 right, 10 left
Dust Port Diameter (in.)...........................................................4..........................................................4
Overall Dimensions (HxWxD/in.)............................. 68 x 34 x 20......................................... 68 x 26 x 19
Motor...............................3/4HP, 1Ph, 115/230V (prewired 115).......1HP, 1Ph, 115/230V (prewired 115)
Net Weight (lbs.).................................................................172...................................................... 185
Shipping Weight (lbs.)......................................................... 183...................................................... 197
The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, Walter Meier reserves the right to change specifications at any time and without
prior notice, without incurring obligations.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking – JWBS-14OS
Open shipping container and check for shipping damage. Report any damage immediately to your
distributor and shipping agent. Read the instruction manual thoroughly for assembly, maintenance and
safety instructions.
Contents of the Shipping Container
1
4
2
2
1
1
1
1
Stand top with motor support plate
Stand legs
Cross braces-short
Cross braces-long
Stand support plate
Saw body
1
1
2
1
1
1
1
1
V-belt
Pulley cover
Table lock knobs
Table pin
Trunnion support bracket
Fastener package (see below)
Instruction Manual
Warranty Card
Table
Motor
Fasteners
A. Stand Assembly (partial quantity shown)
40 – M8x16 carriage bolts
40 – M8 flat washers
4 – rubber grommets
4 – M8 lock washers
4 – M8 hex nuts
40 – M8 lock washers
40 – M8 hex nuts
D. Pulley Cover to Stand
3 – M5x12 pan head screws (approx. 1/2”)
6 – M5 flat washers
B. Saw Body to Stand
4 – M8x40 hex cap screws (approx. 1-1/2")
8 – M8 flat washers
3 – M5 hex nuts
E. Trunnion Support Bracket to Saw Body
2 – M8x30 hex cap screws (approx. 1-1/4")
2 – M8 lock washers
4 – M8 lock washers
4 – M8 hex nuts
C. Motor to Stand
1 – M8x80 hex cap screw (for table stop -
approx. 3-1/8” long)
1 – M8 hex nut (for table stop)
4 – M8x35 hex cap screws (approx. 1-3/8”)
8 – M8 flat washers
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking – JWBS-14CS
Open both shipping containers and check for shipping damage. Report any damage immediately to your
distributor and shipping agent. Read the instruction manual thoroughly for assembly, maintenance and
safety instructions.
Contents of the Shipping Container
Container One:
2
1
1
1
1
1
Table lock knobs
Table pin
Trunnion support bracket
Fastener package (see below)
Instruction Manual
Warranty Card
1
1
1
Closed stand with motor
Pulley cover
V-belt
Container Two:
1
1
Saw body
Table
Fasteners
A. Saw Body to Stand
4 – M8x40 hex cap screws
(approx. 1-1/2" long)
8 – M8 flat washers
4 – M8 lock washers
4 – M8 hex nuts
D. Trunnion Support Bracket to Saw Body
2 – M8x30 hex cap screws
(approx. 1-1/4" long)
2 – M8 lock washers
1 – M8x80 hex cap screw (for table stop -
approx. 3-1/8” long)
1 – M8 hex nut (for table stop)
B. Strain Relief Plate to Stand
2 – M5x12 pan head machine screws
C. Pulley Cover to Base
2 – Knobs
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly of JWBS-14OS
NOTE: If any of the assembly procedures need
further clarification, refer to the exploded views
in the back of this manual.
Tools Required for Assembly
Metric combination wrench set and adjustable
wrench
#1 and #2 cross point screwdrivers
1. Place stand top upside down on a level
surface. Fasten four stand legs to stand top
using carriage bolts, washers, lock washers,
and nuts, as shown in item A on page 7.
Note: Stand legs fasten to outside of stand
top (Figure 1). Do not tighten at this time.
Figure 1
2. Fasten two long braces and two short
braces to stand legs using carriage bolts,
washers, lock washers, and nuts, as shown
in item A, page 7. Do not tighten at this time.
See Figure 2.
3. Turn assembly over and stand it on its legs.
Push down slightly on the top to make sure
the stand settles properly and all four legs
sit flat on a level surface. Tighten all nuts.
Figure 2
Saw body is heavy! Use
caution when lifting and stabilize until firmly
attached to the stand! Failure to comply may
cause serious injury!
4. With the aid of a second person, lift the saw
body out of the shipping container and place
onto the stand top. Be sure front of saw
(with JET logo) faces stand front (JET logo).
See photo on cover for orientation.
5. Line up holes in saw body with holes in
stand. Place support plate to the underside
of stand as shown in the parts diagram for
the open stand assembly (item 5, page 30).
Fasten saw body, stand, and support plate
together with four hex cap screws, eight flat
washers, four lock washers, and four hex
nuts, as shown in item B on page 7.
6. To mount the motor, place four rubber
grommets over holes in stand top (Figure 3).
Note: Use of rubber grommets is essential
for eliminating excessive vibration.
Figure 3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Place motor over rubber grommets and
fasten to stand top with four hex cap
screws, eight flat washers, four lock
washers, and four hex nuts, as shown in
item C, page 7. See Figure 4. The
arrangement of these fasteners is shown in
Figure 5. Do not tighten at this time.
Figure 4
8. Align the motor pulley with the large pulley
using a straight edge against the flat sides
of the pulleys, as shown in Figure 6. The
pulleys should lie in a straight plane (Figure
7). Slide the motor as needed to align the
pulleys. If further adjustment is required,
loosen the set screw in one or more of the
pulleys and move the pulley(s) until they line
up. Tighten set screw(s).
Figure 5
IMPORTANT: When moving the pulleys, do
not position them beyond the end of the
shaft. Both pulleys must fully engage the
shaft and the key.
Figure 6
Figure 7
10
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Place v-belt over both pulleys. See Figure 8.
10. Tension v-belt by moving motor away from
the saw body and tighten the motor mount
nuts. (Do not over-tighten motor mount
bolts. Tighten just enough to tension belt.)
Belt is properly tensioned when finger
pressure between the two pulleys (Figure 8)
causes approximately 1/2” deflection.
11. Place pulley cover over both pulleys and
fasten to stand using three pan head
screws, six washers, and three hex nuts, as
shown in item D, page 7. See Figure 9.
Figure 8
12. Attach trunnion support bracket to saw body
with two hex cap screws and two lock
washers as shown in item E, page 7. See
Figure 10.
13. Thread nut onto table stop bolt (Figure 10)
and attach to trunnion support bracket.
14. To mount table, remove table insert and
table pin (see Figure 11). Orient the table so
that the saw blade will pass through the slot
in the table and into the center opening.
Continue holding up the table, and turn the
table so the two screws that are hanging
vertically from below the table will slide into
the holes on the trunnion support bracket.
Lower the table. The screws should now
protrude below the trunnion support bracket
- attach lock knobs to the ends of these
screws. See Figure 11.
Figure 9
15. Re-install table insert and table pin.
16. Join motor plug to switch plug.
17. Transportation and handling may have
caused some fasteners to loosen. Before
operating, check all screws, bolts, and nuts
to make sure they are snug. Operate
machine only after reading the entire
manual including blade tracking, blade
guide adjustments, and safety rules.
Figure 10
18. Exposed metal surfaces, such as the table,
have been given a protective coating. This
should be cleaned with a soft cloth and
solvent, such as kerosene. Do not use
acetone, gasoline, or lacquer thinner. Do not
use an abrasive pad, and do not get
solvents on plastic parts.
Proceed to “Grounding Instructions” on page 14.
Figure 11
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly of JWBS-14CS
Tools Required for Assembly
Metric combination wrench set and
adjustable wrench
#1 and #2 cross point screwdrivers
Exposed metal surfaces, such as the table, have
been given a protective coating. This should be
cleaned with a soft cloth and solvent, such as
kerosene. Do not use an abrasive pad, and do
not get solvents on plastic parts.
Figure 12
1. Remove pulley cover from inside of stand.
2. Place cabinet stand upright on a level
surface. If desired, the stand can be further
stabilized by securing it to the floor with lag
screws through the inside corner holes. If
using a mobile base, lock the casters before
assembling or operating the band saw.
Saw body is heavy! Use
caution when lifting and stabilize until firmly
attached to the stand! Failure to comply may
cause serious injury!
3. With the aid of a second person, lift the saw
body out of the shipping container and place
onto stand top. Be sure front of saw (with
JET logo) faces stand front (JET logo).
4. Line up holes in saw body with holes in top
of stand. Fasten saw body to the stand with
four M8 x 40 hex cap screws, eight M8
washers, four M8 lock washers, and four M8
hex nuts (as shown in item A, page 8).
Figure 13
5. Push motor cord and strain relief plate
through the opening in the side of the stand
(Fig. 12). Fasten the strain relief plate to the
stand with two M5 x 12 pan head machine
screws (shown in item B, page 8).
6. Check the alignment of the pulleys by
placing a straight edge against the flat sides
of the motor and wheel pulleys (Figure 13).
If the pulleys lie in a straight plane (Figure
14) they are aligned. If they do not lie in a
straight plane, loosen the set screw on one
of the pulleys and shift the pulley in or out
until both pulleys lie in a straight plane.
Tighten set screw.
Figure 14
12
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: When moving the pulleys, do
not position them beyond the end of the
shaft. Both pulleys must fully engage the
shaft and the key.
7. Open the lower door, and place the v-belt
around the motor pulley and the wheel
pulley (see Figure 13).
8. Loosen the nuts on the four motor mounting
bolts (Figure 15) and tension the v-belt by
pushing down on the motor. Tighten the four
motor mounting nuts.
Figure 15
9. The v-belt is properly tensioned when finger
pressure between the two pulleys causes
approximately 1/2" deflection (Figure 16).
Figure 16
10. Screw the two small knobs (Figure 17) into
the threaded holes in the saw body. Slide
the pulley cover down over the knobs, and
tighten the knobs.
Figure 17
11. Attach trunnion support bracket to saw body
with two M8 x 30 hex cap screws and two
M8 lock washers, as shown in item D, page
8. See Figure 18.
12. Thread nut onto table stop bolt (Figure 18)
and attach to trunnion support bracket as
shown.
Figure 18
13
Download from Www.Somanuals.com. All Manuals Search And Download.
13. To mount the table, remove pin and insert
from the table (Figure 19).
14. Orient the table so the saw blade will pass
through the slot in the table and into the
center opening. Continue holding up the
table, and rotate the table so the two screws
that are hanging vertically from below the
table will slide into the holes on the trunnion
support bracket. Lower the table. The
screws should now protrude below the
trunnion support bracket - attach lock knobs
to the ends of these screws. (Figure 19).
Figure 19
15. Re-install table insert and table pin.
16. Connect the plugs of the motor cord and
switch cord (Figure 20).
17. Transportation and handling may have
caused some fasteners to loosen. Before
operating, check all screws, bolts, and nuts
to make sure they are snug. Operate
machine only after reading the entire
manual including blade tracking, blade
guide adjustments, and safety rules.
Figure 20
Grounding Instructions
This band saw must be
grounded while in use to protect the
operator from electric shock.
In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric
shock. This tool is equipped with an electric cord
having an equipment-grounding conductor and a
grounding plug that looks similiar to the plug in
Figure 21. The plug must be inserted into a
matching outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Do not modify the plug provided. If it will not fit
the outlet, have the proper outlet installed by a
qualified electrician.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. The conductor, with insulation
having an outer surface that is green with or
without yellow stripes, is the equipment-
grounding conductor. If repair or replacement of
the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a
live terminal.
Figure 21
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Check with a qualified electrician or service
personnel if the grounding instructions are not
completely understood, or if in doubt as to
whether the tool is properly grounded.
Repair or replace a damaged or worn cord
immediately.
115 Volt Operation
As received from the factory, your band saw is
ready to run at 115 volt operation. This band
saw, when wired for 115 volts, is intended for
use on a circuit that has an outlet and a plug
that looks like the one illustrated in Figure 21. A
temporary adapter, like the adapter in Figure 22,
may be used to connect this plug to a two-pole
receptacle, as shown in Figure 22, if a properly
grounded outlet is not available. The temporary
adapter should only be used until a properly
grounded outlet can be installed by a qualified
electrician. This adapter is not applicable in
Canada. The green colored rigid ear, lug, or tab,
extending from the adapter, must be connected
to a permanent ground such as a properly
grounded outlet box, as shown in Figure 22.
Figure 22
230 Volt Conversion
If 230V, single-phase operation is desired, the
following instructions must be followed:
1. Disconnect machine from power source.
2. This band saw is supplied with four motor
leads that are connected for 115V
operation, as shown in Figure 23.
Reconnect these four motor leads for 230V
operation, as shown in Figure 23.
3. The 115V attachment plug supplied with the
band saw must be replaced with a UL/CSA
listed plug suitable for 230V operation, as
shown in Figure 24. Contact your local
authorized Walter Meier service center or
qualified electrician for proper procedures to
install the plug. The band saw must comply
with all local and national codes after the
230 volt plug is installed.
Figure 23
4. The band saw with a 230 volt plug should
only be connected to an outlet having the
same configuration (Figure 24). No adapter
is available or should be used with the 230
volt plug.
Important: In all cases (115 or 230 volts),
make certain the receptacle in question is
properly grounded. If you are not sure, have
a registered electrician check the receptacle.
Figure 24
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum Gauge Extension Cord
Line Total length of Cord gauge
Extension Cords
Amp
Use only three wire extension cords that have
three-prong grounding plugs and three-pole
receptacles that accept the tool’s plug.
rating voltage cord in feet
(AWG)
0 to 25
18
25 to 50
16
0-6
120
120
Make sure the cord is in good condition, and
heavy enough to carry the current your band
saw will draw. An undersized cord will cause a
drop in line voltage, resulting in loss of power
and overheating. Figure 25 shows the correct
size to use depending on cord length and the
ampere rating on your machine’s nameplate. If
in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
50 to 100
over 100
0 to 25
16
14
18
25 to 50
50 to 100
over 100
0 to 25
16
6-10
14
12
16
25 to 50
50 to 100
over 100
0 to 25
16
Repair or replace a damaged or worn cord
immediately.
10-12
12-16
120
120
14
12
14
12
25 to 50
over 50
not recommended
Adjustments
Figure 25
Unplug the machine from the
power source before making any repairs or
adjustments. Failure to comply may cause
serious injury.
Tilting the Table
1.
Loosen two lock knobs (Figure 26).
2.
Tilt table up to 45 degrees to the right or
up to 10 degrees to the left. The angle can
be read on the scale mounted to the
trunnion.
3.
Tighten two lock knobs (Figure 26).
Figure 26
Note: Table stop must be removed to tilt table to
the left.
Adjusting 90° Table Stop
1.
2.
Disconnect machine from power source.
Loosen lock knobs (Figure 26) and tilt
table left until it rests against the table
stop.
3.
4.
Use a square placed on the table and
against the blade (Figure 27) to see if the
table is 90 degrees to the blade.
If an adjustment is necessary, loosen lock
knobs, tilt table to the right, and lock in
place.
Figure 27
16
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Loosen jam nut and turn table stop (Figure
26) left or right to raise or lower the stop.
Tighten jam nut to hold table stop in place.
6.
7.
Unlock table, tilt back onto table rest and
confirm table is 90 degrees with the blade.
If necessary, adjust scale pointer to zero.
Changing Blades
Blade teeth are sharp! Use
care when handling the saw blade. Failure to
comply may cause serious injury.
Figure 28
1.
2.
Disconnect machine from power source.
Loosen blade tension by turning the
tension knob counterclockwise (Figure 28).
3.
4.
5.
Remove the table insert and the table pin.
Open both wheel covers.
Remove the blade from between upper
and lower blade guides. Remove blade
from upper and lower wheels. Turn blade
to direct through slot in table.
6.
Guide new blade through table slot. Place
blade in upper and lower blade guides.
Note: The blade teeth should face the
operator, and they should point down
toward the table.
7.
Place blade in the middle of the upper and
lower wheel.
8.
9.
Re-install table insert and table pin.
Tension and track blade before operating
saw. Find instructions for tensioning and
tracking the blade under "Adjusting Blade
Tension" and "Adjusting Blade Tracking".
Adjusting Blade Tension
1.
2.
Disconnect machine from power source.
Turn blade tension knob (Figure 28)
clockwise to tension blade. A gauge on the
upper wheel slide bracket indicates the
approximate tension according to the width
of the blade. Initially, set the blade tension
to correspond to the blade width as marked
on the gauge.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
As you become more experienced with the
saw, you may find it necessary to change
the blade tension from the initial setting.
Changes in blade width and the type of
material being cut will have an effect on
blade tension.
Keep in mind that too little or too much
blade tension can cause blade breakage.
Adjusting Blade Tracking
Disconnect machine from the
power source. Never adjust blade tracking
with the machine running. Failure to comply
may cause serious injury.
“Tracking” refers to how the blade is situated
upon the wheels while in motion. The blade
should track in the center of both wheels.
1.
The blade must be properly tensioned
before adjusting blade tracking. Make sure
blade guides and blade bearings do not
interfere with the blade.
Figure 29
2.
3.
Open the top wheel cover. Rotate the wheel
forward by hand, and observe the position
of the blade on the wheel - it should be in
the center of the wheel.
If adjustment is necessary, loosen wing nut
(Figure 29), and tighten tracking knob
slightly to move blade toward rear of
machine. Slightly loosening the tracking
knob will cause the blade to track toward the
front of the machine.
4.
After blade is tracking in the center of the
wheel, tighten the wing nut.
Adjusting Upper Blade Guide
Assembly
1.
2.
Disconnect machine from power source.
Loosen lock knob (A, Figure 30) and raise
or lower upper blade guide assembly (B,
Figure 30) to just above the material being
cut.
Figure 29
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
Tighten lock knob. Make sure blade guide
blocks (C, Figure 30) are still flat to the
blade. If adjustment is necessary, loosen
lock knob (A, Figure 30) and rotate
assembly until guide blocks are flat to blade.
If movement of the blade guide assembly
seems “stiff” when being raised or lowered,
it can be adjusted to slide more easily. This
is controlled by an internal spring and ball
which provide varying degrees of resistance
against the guide post. Use the set screw
(D, Figure 30) to adjust the tension of this
spring. To adjust tension on the spring,
loosen knob (A, Figure 30), use a hex
wrench to tighten or loosen set screw (D,
Figure 30) until desired tension is reached,
then re-tighten knob (A, Figure 30).
Adjusting Blade Guide and Blade
Support Bearing
Blade guard has been
removed for picture clarity. Never operate
the band saw without all guards in place and
in working order.
1.
Disconnect machine from power source.
2.
3.
Blade must already be tensioned and
tracking properly.
Loosen thumb screws (E, Figure 31) and
move guide blocks (C, Figure 31) as close
to the blade as possible without pinching it.
Figure 31
4.
5.
Tighten thumb screws (E, Figure 31).
Loosen thumb screw (F, Figure 31) and turn
knurled knob (G, Figure 31) to move the
guide block bracket in or out until the front
edge of the guide blocks are just behind the
"gullets" of the saw teeth.
6.
7.
Tighten thumb screw (F, Figure 31).
The blade support bearing (K, Figure 31)
should be adjusted so that the back edge of
the blade overlaps the front face of the ball
bearing approximately 1/8". To change
position of the bearing, remove screw (L,
Figure 31), and bearing (K, Figure 31).
Loosen thumb screw (H, Figure 31) and
back off knurled knob (J, Figure 31)
completely to remove the bearing shaft.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
Notice the bearing holder on the shaft is
eccentric. Index the bearing shaft to another
position and slide it back in, making sure the
flange on the thumb screw (H, Figure 31)
properly seats into the groove of the bearing
shaft. Re-install the bearing and the screw.
Examine the overlap between the bearing
face and the blade. Change the position of
the bearing shaft until the overlap is
approximately 1/8".
9.
With the thumb screw (H, Figure 31) still
loosened, adjust the distance from bearing
to blade. Turn knurled knob (J, Figure 31) to
move the support bearing (K, Figure 31) in
or out until the bearing is 1/64" behind the
blade. (NOTE: To set this distance quickly,
you can place a dollar bill or piece of paper
between support bearing and back of
blade.)
Figure 31
(repeated)
10. Tighten thumb screw (H, Figure 31).
11. Repeat procedures 1 through 10 for the
Lower Blade Guide Assembly.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting JWBS-14CS/OS Band Saw
Trouble
Probable Cause
Remedy
Saw unplugged.
Check all plug connections.
Saw stops or will not
start.
Fuse blown, or circuit breaker tripped. Replace fuse, or reset circuit breaker.
Cord damaged.
Replace cord.
Check blade with square and adjust
table stop.
Table stop not adjusted correctly.
Does not make
accurate 45 or 90
degree cuts.
Check blade with square and adjust
pointer.
Angle pointer not set accurately.
Miter gauge out of adjustment.
Fence not aligned with blade.
Adjust miter gauge.
Check and adjust fence (see fence
manual).
Warped wood.
Select another piece of wood.
Reduce feed rate.
Excessive feed rate.
Incorrect blade for cut.
Blade wanders during
cut.
Change blade to correct type.
Set blade tension according to blade
size.
Blade tension not set properly.
Guides not set properly.
Dull blade.
Adjust guides.
Replace blade.
Teeth should face operator and point
downward.
Blade mounted wrong.
Gum or pitch on blade.
Saw makes
unsatisfactory cuts.
Remove blade and clean with oven
cleaner or other solvent.
Incorrect blade for cut.
Gum or pitch on table.
Change blade to correct type.
Clean table.
Replace with adequate size and
length cord.
Extension cord too light or too long.
Blade does not come
up to speed.
Low shop voltage.
Base on uneven floor.
Bad v-belt.
Contact your local electric company.
Reposition on flat, level surface.
Replace v-belt.
Saw vibrates
excessively.
Motor mounting is loose.
Loose fasteners.
Tighten motor mount fasteners.
Tighten fasteners.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
708718R JRF-14 Deluxe Rip Fence Assembly with Resaw
Includes guide bars, rip fence assembly, resaw post, fasteners, and mounting instructions with
parts list.
708717 JRB-14 Riser Block Kit
Increases depth of cut from 6" maximum to 12" maximum. Includes 6" cast block, long frame
bolt, front and back blade guards, 105” blade, and mounting instructions with parts list.
708716 JMG-14 Miter Gauge Assembly
For straight and angle cutting. Includes guide bar, pivoting support body, and adjustable
stops.
708719 JBB-14 Blade Block Set
Includes upper and lower replacement blocks made from a non-metallic composite material
with a dry lubricant to reduce friction and heat.
708127 JRBG-14 Roller Bearing Guides
Dual bearing system maximizes contact and minimizes friction against the blade. Includes
upper and lower guide assemblies, mounting studs, adaptor blocks, and mounting hardware.
Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call
1-800-274-6848, Monday through Friday (see our website for business hours, www.waltermeier.com).
Having the Model Number and Serial Number of your machine available when you call will allow us to
serve you quickly and accurately.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Body Assembly (JWBS-14CS/OS Band Saw)
Index No. Part No.
Description
Size
Qty
1.............. 150100AW ..............Upper Arm Frame...............................................................................1
2.............. 150037W ................Table .................................................................................................1
3.............. 100038....................Table Pin............................................................................................1
4.............. 708719....................Guide Block........................................................................................4
5.............. 150005A .................Upper Support Bracket Post................................................................1
6.............. 150006A .................Support Bracket..................................................................................2
7.............. 150007A .................Guide Post .........................................................................................1
8.............. TS-1490021 ............Hex Cap Screw ................................................M8x16........................2
9.............. WF083030 ..............Flat Washer......................................................M8.............................1
10............ 150010A .................Nut ....................................................................................................4
11............ 990708....................Screw ..............................................................M8x40........................2
12............ TS-1482031 ............Hex Cap Screw ................................................M6x16........................1
13............ 150013A .................Thumb Screw ...................................................M6x16........................3
14............ 150014A .................Thumb Screw ..................................................M6x12........................5
15............ 150015A .................Upper Spacing Sleeve ........................................................................2
16............ BB-6200ZZ..............Ball Bearing........................................................................................2
17............ 990908....................Pan Head Screw* .............................................M6x8 .........................2
18............ 100002A .................Upper Wheel Blade Guard ..................................................................1
19............ TS-148201 ..............Hex Cap Screw ................................................M6X10.......................2
20............ TS-1550041 ............Washer ............................................................M6.............................4
21............ 990651....................Lock Knob........................................................M10x30......................1
22............ 199037....................Table Insert ........................................................................................1
23............ 992311....................Spring Pin ..........................................................................................1
25............ TS-1482041 ............Phillips Pan Head Machine Screw......................M6x20........................2
26............ 150024....................Catch Knob ........................................................................................2
27............ TS-1551061 ............Lock Washer*...................................................M8....................... 2(2)*
28............ 150028W ................Inner Wheel Cover..............................................................................1
29............ 155029W ................Outer Wheel Cover .............................................................................1
30............ 100031....................Pin.....................................................................................................4
31............ 990180....................Hex Head Bolt ..................................................M16x55......................1
32............ WF-164030 .............Washer ............................................................M16...........................2
33............ TS-1540101 ............Hex Nut............................................................M16...........................1
34............ 100188....................Base..................................................................................................1
35............ 110045....................Trunnion Support Bracket....................................................................1
36............ 100042....................Trunnion ............................................................................................2
37............ 100051....................Scale .................................................................................................1
38............ 100041....................Trunnion Clamp Shoe .........................................................................2
39............ TS-1491081 ............Hex Cap Screw ................................................M10x50......................2
40............ TS-1482021 ............Hex Cap Screw ................................................M6x12........................6
41............ 110049....................Pointer ...............................................................................................1
42............ 990821....................Pan Head Screw...............................................M5x6 .........................5
43............ TS-1490151 ............Hex Cap Screw*...............................................M8x80........................1
44............ TS-1540061 ............Hex Nut* ..........................................................M8.............................1
45............ TS-1490051 ............Hex Cap Screw*...............................................M8X30.......................2
46............ 990554....................Lock Knob........................................................ .................................2
47............ TS-152303 ..............Set Screw ........................................................M6x10........................1
48............ 100063....................Belt Pulley..........................................................................................1
49............ 992547....................Retaining Ring....................................................................................1
50............ 110065....................Lower Wheel Shaft .............................................................................1
51............ 992009....................Key..................................................................5x5x20.......................2
52............ BB-6204RS .............Ball Bearing......................................................6204RS......................2
53............ 990293....................Hex Head Bolt (Left Thread)..............................M8x25........................1
54............ 150054....................Hex Head Bolt ....................................................................................2
55............ 150055....................Lower Support Bracket Post................................................................1
56............ 150056....................Switch Backing Plate ..........................................................................1
57............ 523028....................Switch Box.........................................................................................1
58............ 994542....................Switch................................................................................................1
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Body Assembly (JWBS-14CS/OS Band Saw)
Index No. Part No.
Description
Size
Qty
59............ 995001....................Power Cord (Switch To Motor).............................................................1
60............ 995002....................Power Cord (Switch To Power Soure) ..................................................1
61............ 990814....................Self Tapping Screw...........................................M3.5x19.....................2
62............ TS-1550021 ............Flat Washer......................................................M4.............................2
63............ TS-1533042 ............Phillips Pan Head Machine Screw......................M5x12........................6
64............ 523024....................Wire Clip ............................................................................................1
65............ TS-1533032 ............Phillips Pan Head Machine Screw......................M5x10........................4
66............ 150066....................Stud...................................................................................................2
67............ 150902....................Lower Hinge.......................................................................................1
68............ WF051210 ..............Washer ............................................................M5.............................2
69............ 150069N .................Lower Wheel Guard............................................................................1
70............ 198672....................Lower Wheel ......................................................................................1
71............ 100025A ................Wheel Protector..................................................................................2
72............ 198242....................Upper Wheel ......................................................................................1
73............ 992522....................Retaining Ring..................................................R35 ...........................2
74............ BB-6202ZZ..............Ball Bearing......................................................6202ZZ ......................2
75............ TS-1540083 ............Hex Nut............................................................M12...........................1
76............ ...............................Saw Blade (Local Purchase)................................................................1
77............ 990804....................Self Tapping Screw...........................................M4x8 .......................16
78............ 150901....................Upper Hinge.......................................................................................1
79............ 150079....................Catch.................................................................................................2
80............ 150080....................Clip....................................................................................................2
81............ 150081....................Bracket ..............................................................................................2
82............ 110070....................Blade Guard.......................................................................................1
83............ 990811....................Self Tapping Screw...........................................M3.5x12.....................2
................ 100016ACP.............Sliding Bracket Assy (includes items 84 thru 93, and 104) .....................1
84............ 100016A .................Sliding Bracket ...................................................................................1
85............ 100019....................Shaft Hinge ........................................................................................1
86............ 150086....................Upper Wheel Shaft .............................................................................1
87............ 100021....................Steel Pin ............................................................................................2
88............ 992314....................Spring Pin ..........................................................................................1
89............ 100015A .................Coil Spring .........................................................................................1
90............ 150090....................Square Nut.........................................................................................1
91............ 990652....................Lock Knob..........................................................................................1
92............ NW080000 ..............Wing Nut..........................................................M8.............................1
93............ 990653....................Blade Adjusting Screw ........................................................................1
95............ TS-1490071 ............Hex Cap Screw*...............................................M8x40........................4
96............ TS-1550061 ............Flat Washer* ....................................................M8.............................4
97............ 150097....................Washer ..............................................................................................2
98............ 994181....................Steel Ball............................................................................................1
99............ 150099....................Spring................................................................................................1
100.......... TS-1525011 ............Socket Set Screw .............................................M10x10......................1
101.......... 150101....................Lower Wheel Blade Guard ..................................................................1
102.......... WE050000 ..............Gear Washer....................................................M5.............................2
103.......... 998654....................Strain Relief .......................................................................................2
104.......... 100018....................Indicator.............................................................................................1
105.......... WI080000................Gear Washer....................................................M8.............................2
................ JWBS14-HK ............Hardware Kit (not shown) ....................................................................1
* .............. included in hardware kit
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Body Assembly (JWBS-14CS/OS Band Saw)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Closed Stand Assembly (JWBS-14CS Band Saw)
Index No. Part No.
Description
Size
Qty
1.............. 150501W ................Stand.................................................................................................1
2.............. 150502W ................Door ..................................................................................................1
3.............. 150503....................Door Latch Assembly..........................................................................1
4.............. WBS14CS-04..........Washer ..............................................................................................2
5.............. WBS14CS-05..........Pan Head Screw...............................................M4x5 .........................2
6.............. PG-M02 ..................JET Plaque ........................................................................................1
7.............. TS-1533031 ............Flat Head Screw...............................................M5x10........................2
8.............. 150508W ................Plate..................................................................................................1
9.............. 998621....................Strain Relief .......................................................................................1
10............ TS-1533042 ............Phillips Pan Head Machine Screw* ....................M5x12........................2
11............ 150511W ................Motor Plate.........................................................................................1
12............ 150512W ................Motor...............................................................1HP, 1Ph, 115/230V ...1
13............ 600013....................Motor Pulley .......................................................................................1
14............ VB-A50 ...................V-BELT..............................................................................................1
15............ TS-1523011 ............Socket Set Screw .............................................M6x6 .........................1
16............ 100254....................Pulley Box..........................................................................................1
17............ 990624....................Knob*.................................................................................................2
20............ TS-1490041 ............Hex Cap Screw ................................................M8x25........................4
21............ 991516....................Square Neck Bolt..............................................M8x16........................4
22............ TS-1550051 ............Flat Washer* ....................................................M8......................16(4)*
23............ TS-155108 ..............Lock Washer*...................................................M8......................12(4)*
24............ TS-1540061 ............Hex Nut* ..........................................................M8......................12(4)*
26............ 995003A .................Motor Cord.........................................................................................1
27............ 150527....................Pad....................................................................................................2
................ WBS14CS-HK .........Hardware Kit (Not Shown)...................................................................1
* .............. included in hardware kit
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Closed Stand Assembly (JWBS14-CS Band Saw)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Open Stand Assembly (JWBS-14OS Band Saw)
Index No. Part No.
Description
Size
Qty
1.............. 150602W ................Top Plate ...........................................................................................1
2.............. 150603W ................Stand Leg ..........................................................................................4
3.............. 150604W ................Support Plate-long..............................................................................2
4.............. 150605W ................Support Plate-short.............................................................................2
5.............. 150606W ................Support Plate-upper............................................................................1
6.............. 150607W ................Pulley Cover.......................................................................................1
7.............. 150608W ................Inner Pulley Cover ..............................................................................1
8.............. 990804....................Self Tapping Screw...........................................M4x8 .........................5
9.............. 150609W ................Motor.................................................................................................1
10............ 600013....................Motor Pulley .......................................................................................1
11............ VB-A39 ...................V-belt.................................................................................................1
12............ TS-1523011 ............Socket Set Screw .............................................M6x6 .........................1
13............ PG-M02 ..................JET Plaque ........................................................................................1
14............ TS-1533031 ............Flat Head Screw...............................................M5X10.......................2
15............ TS-1490061 ............Hex Cap Screw*...............................................M8x35........................4
16............ 991516....................Carriage Bolt*...................................................M8x16......................40
17............ TS-15550051...........Washer*...........................................................M8...........................52
18............ TS-155108 ..............Lock Washer*...................................................M8...........................48
19............ TS-1540061 ............Hex Nut* ..........................................................M8...........................48
20............ TS-1533042 ............Phillips Pan Head Machine Screw* ....................M5x12........................3
21............ TS-1550031 ............Flat Washer* ....................................................M5.............................6
22............ TS-1540041 ............Hex Nut* ..........................................................M5.............................3
23............ 150623....................Rubber Mount* ...................................................................................4
24............ 150624....................Support Plate .....................................................................................1
25............ 995004A .................Motor Cord.........................................................................................1
26............ 150627....................Pad....................................................................................................1
27............ JWBS14OS-208 ......Rubber Foot (set of 4).........................................................................1
................ WBS14OS-HK.........Hardware Kit (not shown) ....................................................................1
* .............. included in hardware kit
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Open Stand Assembly (JWBS-14OS Band Saw)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections – 115 volt (JWBS-14CS/OS Band Saw)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections – 230 volt (JWBS-14CS/OS Band Saw)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086
Phone: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|